VALVOLE VK20-VK32-VK40-VK50 - hytekintl.com - Valvole_VK20_VK32_VK40... · valvole...
Transcript of VALVOLE VK20-VK32-VK40-VK50 - hytekintl.com - Valvole_VK20_VK32_VK40... · valvole...
VALVOLE VK20-VK32-VK40-VK50
5a
VK20-VK32-VK40-VK50 VALVES
VK20 - 1”
VK20- Materiale del corpo valvola: _______________________ Noryl ® - Entrata / Uscita: ____________________________________ 1 “ BSPPortata Valvola sola- In continuo (Dp = 1,0 bar): _______________________ 4,1 m3/h- Valore massimo (Dp = 2,0 bar): __________________ 5,5 m3/h- Contolav. max: _________________________________ 1,2 m3/hMicroprocessore- Visualizzazione: ______________ Display digitale retro illuminato- Alimentazione elettrica:Con trasformatore: ______________________ 230 V / 5V – 1A – DC * Pile alcaline: _____2 pile “professionali” di qualità LR20 (1.5V) - Parametri impostabili: Ora del giorno, ora di rigenerazione, tempi dei cicli, capacità ciclica, forzatura a tempo, riserva. - Lettura: Volume restante, defalco del tempo, posizione del ciclo in corso.- Rigenerazione: a giorni fissi, a giorni selezionabili, volumetrica ritardata o immediata, manuale.- Modalità Rigenerazione: Up Flow, Down Flow, Filtro, Salamoia variabileCaratteristiche:- Rigenerazione DF & UF senza costi aggiuntivi (stesso pistone)- Regolazione dei Cicli- Riempimento vasca sale con acqua addolcita (solo UF)- Salamoia variabile- Manutenzione semplificata (iniettori, regolatori scarico etc)- Rapida connessione alla linea di scarico- Facile disassemblaggio del corpo dall’ adattatore - Contatore integrato- Miscelatore della durezza integrato Dimensioni- Tubo distributore: _________________________________ 27 mm - Altezza tubo distributore dalla bombola: __+13 mm (+/- 3 mm)- Conduttura allo scarico: _____________________ 1/2” (13 mm) - Conduttura alla salamoia: ____________________________ 3/8” - Filettatura bombola: ________________________ 2 ½” - 8 NPSM - Altezza: __________________________________________ 119 mm- Larghezza: ________________________________________ 206 mm- Profondità con attacco in/out:____________________ 200 mm- Peso con attacco in/out:: ____________________________ 1.6 kgBombole utilizzabili- Addolcitore: ____________________________________Ø 6”- 14”- Filtri:_____________________________________________Ø 6” - 12” - Volume resina: _____________________________ da 4,5 lt a 102 ltPressione- Idrostatica: ________________________________________ 14 bar- Servizio: _________________________________________ 2 a 8 bar- Temperatura: ____________________________________1 a 45°C- Test pressione: __ 1-14 bar (250.00 cicli) Opzioni- * Valvola con pile alcaline LR20 (1.5V) opzionale- Acqua Calda - Valvola filtro- SBV di sicurezza- Produttore di cloro incorporato- 2 Micro switch ausiliari con cavo (VK0040-1)Certificati- Conformità Regolamento CE bassa tensione- CE - RoHS- ACS : 13 ACC LY 804
HYK-VALVES
VK20- Valve material: ____________________________________ Noryl ®- Inlet / outlet:_______________________________________ 1 “ BSPFlow rate valve alone- Continuous (1,0 bar drop): ________________________ 4,1 m3/h - Peak (2,0 bar drop): ______________________________ 5,5 m3/h- Max backwash: __________________________________ 1,2 m3/hMicroprocessor- Display: ____________________________ Large backlight display - Power supply:*With transformer: _________________________ 230 V / 5V – 1A – DC * Alkaline battery:_2 “professional” quality Alkaline battery LR20 (1.5V)- Adjustable parameters: time of day, time of regeneration, cycles time, cyclical capacity, time forcing, reserve.- Reading: volume remaining, remaining time, cycle in pro-gress.- Regeneration: Hours, Timeclock, Meter delayed or immedi-ate, manual.- Regeneration Mode: Downflow / Upflow, Filter, Variable brin-ingGeneral Features:- DF & UF rigeneration without additional costs (same piston)- Adjustable cicles- Brine fill with softened water (only UF)- Variable Brining- Easier maintenance (injectors, flow regulators, etc)- Quick connexion to the drain line - Easy disassembly of the body from the adaptor- Integrated meter- Integrated mixing deviceDimensions:- Distributor pilot: ____________________________________ 27 mm- Length distributor tube from the tank: __+13 mm (+/- 3 mm)- Drain line: ____________________________________1/2” (13 mm) - Brine line: ____________________________________________ 3/8” - Mounting base: _____________________________ 2 ½” - 8 NPSM - Height: ___________________________________________ 119 mm- Width: ____________________________________________ 206 mm - Depth with in/out yoke: ___________________________ 200 mm- Weight with in/out yoke: ____________________________ 1.6 kgTanks Size application (recommended) - Water softener: __________________________________Ø 6”- 14”- Filter: ____________________________________________ Ø 6” - 12” - Resin volume: _________________________ from 4,5 lt up to 102 ltPressure- Hydrostatic:_______________________________________ 14 bar- Working:________________________________________ 2 to 8 bar- Temperature:____________________________________1 to 45°C- Pressure Test:_1-14 bar (250.00 cycles) Options- * Valve with alkaline battery LR20 (1.5V) optional- Hot Water- Filter valve- SBV Safety brine Valve- Chlorine producer on board- 2 Auxiliary microswitches with cable (VK0040-1)Certificates- Compliant to CE low voltage regulations - CE - RoHS- ACS : 13 ACC LY 804
7– DIMENSIONS & CARACTERISTIQUES
Section nominale : Ø 19 mm (¾'') minimum Raccordements hydrauliques entrée / sortie : ¾'' BSP cylindrique Raccordement à l'égout : tube Ø 13 mm Raccordement au bac à sel : tube PE Ø 9,52 mm (3/8'') Vanne conforme aux directives européennes N° 89/339/EEC, Compatibilité électromagnétique N° 73/23/EEC, Basse tension N° 2002/95/CE, RoHs Attestation de conformité sanitaire : ACS N° 13 ACC LY 804 Pression minimale en service : 2 bars Pression maximale en service : 8 bars Pression d'épreuve : 14 bars Température minimale de fonctionnement : 1°C Température maximale de fonctionnement : 45°C Alimentation électrique : 2 piles LR 20 (1,5 volts) alcaline qualité « Professionnel » Alimentation optionnelle: transformateur 230 V / 5V – 1 A – DC
14
HYK-VALVESVK20 - 1”
DIMENSIONI VK20 UP-FLOW/ UP-FLOW VK20 DIMENSIONS
SCHEMI DI FLUSSO VK20 UP-FLOW/ UP-FLOW VK20 FLOW DIAGRAMS
Outlet port Drain port Inlet port
Raw waterTreated waterRegen waterBrine
CAPPERS SCA 19
Outlet port Drain port Inlet port
Raw waterTreated waterRegen waterBrine
CAPPERS SCA 19 Outlet port Drain port Inlet port
Brine port
Raw waterTreated waterRegen waterBrine
CAPPERS SCA 19
Outlet port Drain port Inlet port
Raw waterTreated waterRegen waterBrine
CAPPERS SCA 19Outlet port Drain port Inlet port
Brine port
Raw waterTreated waterRegen waterBrine
CAPPERS SCA 19
ScaricoDrain
UscitaOutlet
IngressoInlet
H2O grezza /Raw H2OH2O trattata /Treated H2OH2O di rigen. /Regen H2OSalamoia /Brine
ScaricoDrain
UscitaOutlet
IngressoInlet
H2O grezza /Raw H2OH2O trattata /Treated H2OH2O di rigen. /Regen H2OSalamoia /Brine
H2O grezza /Raw H2OH2O trattata /Treated H2OH2O di rigen. /Regen H2OSalamoia /Brine
H2O grezza /Raw H2OH2O trattata /Treated H2OH2O di rigen. /Regen H2OSalamoia /Brine
H2O grezza /Raw H2OH2O trattata /Treated H2OH2O di rigen. /Regen H2OSalamoia /Brine
ScaricoDrain
UscitaOutlet
IngressoInlet
ScaricoDrain
UscitaOutlet
IngressoInlet
Linea NaCLBrine line
ScaricoDrain
UscitaOutlet
IngressoInlet
Linea NaCLBrine line
Servizio Up-Flow Up-Flow Service
Controlavaggio Backwash
Aspirazione salamoiaBrine Suction
Risciacquo rapidoRapid rinse
RiempimentoBrine refill
SCHEMI DI FLUSSO VK20 DOWN-FLOW/ DOWN-FLOW VK20 FLOW DIAGRAMSScaricoDrain
UscitaOutlet
IngressoInlet
H2O grezza /Raw H2OH2O trattata /Treated H2OH2O di rigen. /Regen H2OSalamoia /Brine
ScaricoDrain
UscitaOutlet
IngressoInlet
H2O grezza /Raw H2OH2O trattata /Treated H2OH2O di rigen. /Regen H2OSalamoia /Brine
H2O grezza /Raw H2OH2O trattata /Treated H2OH2O di rigen. /Regen H2OSalamoia /Brine
H2O grezza /Raw H2OH2O trattata /Treated H2OH2O di rigen. /Regen H2OSalamoia /Brine
H2O grezza /Raw H2OH2O trattata /Treated H2OH2O di rigen. /Regen H2OSalamoia /Brine
ScaricoDrain
UscitaOutlet
IngressoInlet
ScaricoDrain
UscitaOutlet
IngressoInlet
Linea NaCLBrine line
ScaricoDrain
UscitaOutlet
IngressoInlet
Linea NaCLBrine line
Servizio Up-Flow Up-Flow Service
Controlavaggio Backwash
Aspirazione salamoiaBrine Suction
Risciacquo rapidoRapid rinse
RiempimentoBrine refill
7– DIMENSIONS & CARACTERISTIQUES
Section nominale : Ø 19 mm (¾'') minimum Raccordements hydrauliques entrée / sortie : ¾'' BSP cylindrique Raccordement à l'égout : tube Ø 13 mm Raccordement au bac à sel : tube PE Ø 9,52 mm (3/8'') Vanne conforme aux directives européennes N° 89/339/EEC, Compatibilité électromagnétique N° 73/23/EEC, Basse tension N° 2002/95/CE, RoHs Attestation de conformité sanitaire : ACS N° 13 ACC LY 804 Pression minimale en service : 2 bars Pression maximale en service : 8 bars Pression d'épreuve : 14 bars Température minimale de fonctionnement : 1°C Température maximale de fonctionnement : 45°C Alimentation électrique : 2 piles LR 20 (1,5 volts) alcaline qualité « Professionnel » Alimentation optionnelle: transformateur 230 V / 5V – 1 A – DC
14
DIMENSIONI VK20 DOWN-FLOW/ DOWN-FLOWVK20 DIMENSIONS
VK20 - 1”HYK-VALVES
RICAMBI VK20/ VK20 SPARE PARTS
VK20 - 1” HYK-VALVES
DC
-C-0
18-R
05
Down-flow standard settings for 120 grams of salt per resin liter
Tank Breech Cycle 1 Cycle 2 Cycle 3 Cycle 4
Dimmensions
Volume BackwashBrining(draw)
Slowrince
Rapidrince
Tank refill
Tank Resin Brine Salt Time Flow Time Flow Time Time Volume Time
(L) (L) (L) (Kg) (mn) (L/mn) (mn) (L/mn) (mn) (mn) (L) (mn)
6 x18 6,8 4,5 1,68 0,54 1 4 0,5 3,9 0,84 12 3 1,50 1,5
6 x 35 14 9,5 3,56 1,14 1 4 0,5 7,6 0,84 23 4 3,17 3,2
7 x 35 20 13 4,88 1,56 3 5 0,75 7 1,29 21 4 4,33 4,3
8 x 35 25 17 6,19 1,98 3 6 0,75 8,8 1,29 26 4 5,50 5,5
9 x 35 31 21 7,77 2,49 5 6 1 8,3 1,89 25 5 6,91 6,9
10 x 35 39 25 9,55 3,06 5 7 1 10,1 1,89 30 5 8,49 8,5
10 x 44 50 33 12,25 3,92 7 7 1,2 10,7 2,37 32 5 10,89 10,9
12 x 48 78 51 19,31 6,18 7 8 1,2 16,6 2,37 50 5 17,16 17,2
Tank Breech Cycle 1 Cycle 2 Cycle 3 Cycle 4
Dimmensions
VolumeBrining(draw)
Slowrince
BackwashRapidrince
Tank refill
Tank Resin Brine Salt Flow Time Flow Temps Time Time Volume Time
(L) (L) (L) (Kg) (L/mn) (mn) (L/mn) (mn) (mn) (mn) (L) (mn)
7 x 35 20 13 4,88 1,56 1 0,5 10,3 0,84 31 6 5 4,33 4,3
8 x 35 25 17 6,19 1,98 1 0,5 12,9 0,84 39 8 5 5,50 5,5
9 x 35 31 21 7,77 2,49 3 0,75 10,9 1,29 33 9 5 6,91 6,9
10 x 35 39 25 9,55 3,06 3 0,75 13,2 1,29 40 10 5 8,49 8,5
10 x 44 50 33 12,25 3,92 5 1 12,8 1,89 38 10 6 10,89 10,9
12 x 48 78 51 19,31 6,18 5 1 19,8 1,89 59 10 6 17,16 17,2
13 x 54 104 69 25,74 8,24 7 1,2 22,0 2,37 66 10 8 22,88 22,9
14 x 65 154 102 38,12 12,2 7 1,2 32,3 2,37 97 14 8 33,88 33,9
Up-flow standard settings for 120 grams of salt per resin liter
Nota: these values are only setting indications to apply to softeners with SCA-19 valve. They are determined for standard resin use and for an average temperature of 15°C. They must be adapted in accordance with the specifical installation location data. In any case, they involve Cappers’ responsability.
SCA-19 ModelStandard settings
Breech n°1 Breech n°3 Breech n°5 Breech n°7
Soft
en
er
Co
ntr
ol
Ad
van
ce
Cappers S.A.SZ.I. de Feletrue Edouard Michelin63300 Thiers - FranceTel : +33(0)4 73 94 84 87
Kj-34-E0-520 Kj-34-E0-521
Brine seals kitKj-34-E0-517
Tank seal O-ring tube seal Ø 25 mm (x5)
Bypass kit Kb-40-D0-540
Inlet outlet seal kit (x5) Interface seal kit (x5)
New Main seals & spacers kit
Price list 2016-2Apply your discount to obtain your net prices
Kj-34-E0-518 Kj-34-E0-519
Breech seals kitKj-34-E0-515 Ke-40-D0-635
Page 14 de 40
VK2111-1 VK2111-3 VK2111-5 VK2111-7
VK2253
6 – PIECES DE RECHANGE
Joints de culasse (1 kit) Kj-34-E0-515 (VK2253)
culasse n°1 : Co – 33 – T1 – 05 blanc (VK2111-1)
culasse n°3 : Co – 33 – T1 – 07 orange (VK2111-3) culasse n°5 : Co – 33 – T1 – 09 vert (VK2111-5)
culasse n°7 : Co – 33 – T1 – 11 violet (VK2111-7)
couvre culasse Ca – 33 – T1 - 03 (VK2254)
Kit piston et tiges (VK2194) Kp-40-D0 -634
Joints principaux (1 kit) Kj - 34 - E0 - 516 (VK2066)
raccord de saumurage Kr – 40 - D0 - 525 (VK2265)
Mitigeur
Km – 40 - D0 - 526 (VK2257)Plaque piston
Ka – 40 - D0 - 524 VK2258
Joints de saumurage
Kj - 34 - E0 - 517 (VK2113) Kit joints et entretoises nouveau
Ke-40-D0-635 (VK2114)
11
VK2194
6 – PIECES DE RECHANGE
Joints de culasse (1 kit) Kj-34-E0-515 (VK2253)
culasse n°1 : Co – 33 – T1 – 05 blanc (VK2111-1)
culasse n°3 : Co – 33 – T1 – 07 orange (VK2111-3) culasse n°5 : Co – 33 – T1 – 09 vert (VK2111-5)
culasse n°7 : Co – 33 – T1 – 11 violet (VK2111-7)
couvre culasse Ca – 33 – T1 - 03 (VK2254)
Kit piston et tiges (VK2194) Kp-40-D0 -634
Joints principaux (1 kit) Kj - 34 - E0 - 516 (VK2066)
raccord de saumurage Kr – 40 - D0 - 525 (VK2265)
Mitigeur
Km – 40 - D0 - 526 (VK2257)Plaque piston
Ka – 40 - D0 - 524 VK2258
Joints de saumurage
Kj - 34 - E0 - 517 (VK2113) Kit joints et entretoises nouveau
Ke-40-D0-635 (VK2114)
11
VK2254
6 – PIECES DE RECHANGE
Joints de culasse (1 kit) Kj-34-E0-515 (VK2253)
culasse n°1 : Co – 33 – T1 – 05 blanc (VK2111-1)
culasse n°3 : Co – 33 – T1 – 07 orange (VK2111-3) culasse n°5 : Co – 33 – T1 – 09 vert (VK2111-5)
culasse n°7 : Co – 33 – T1 – 11 violet (VK2111-7)
couvre culasse Ca – 33 – T1 - 03 (VK2254)
Kit piston et tiges (VK2194) Kp-40-D0 -634
Joints principaux (1 kit) Kj - 34 - E0 - 516 (VK2066)
raccord de saumurage Kr – 40 - D0 - 525 (VK2265)
Mitigeur
Km – 40 - D0 - 526 (VK2257)Plaque piston
Ka – 40 - D0 - 524 VK2258
Joints de saumurage
Kj - 34 - E0 - 517 (VK2113) Kit joints et entretoises nouveau
Ke-40-D0-635 (VK2114)
11
VK2265
6 – PIECES DE RECHANGE
Joints de culasse (1 kit) Kj-34-E0-515 (VK2253)
culasse n°1 : Co – 33 – T1 – 05 blanc (VK2111-1)
culasse n°3 : Co – 33 – T1 – 07 orange (VK2111-3) culasse n°5 : Co – 33 – T1 – 09 vert (VK2111-5)
culasse n°7 : Co – 33 – T1 – 11 violet (VK2111-7)
couvre culasse Ca – 33 – T1 - 03 (VK2254)
Kit piston et tiges (VK2194) Kp-40-D0 -634
Joints principaux (1 kit) Kj - 34 - E0 - 516 (VK2066)
raccord de saumurage Kr – 40 - D0 - 525 (VK2265)
Mitigeur
Km – 40 - D0 - 526 (VK2257)Plaque piston
Ka – 40 - D0 - 524 VK2258
Joints de saumurage
Kj - 34 - E0 - 517 (VK2113) Kit joints et entretoises nouveau
Ke-40-D0-635 (VK2114)
11
VK2066
Op-40-D0-543 Adaptation for 27 mm (1,05") distributor 1 10,18 €
Op-32-T1-546 Needle screw mixing device 1 4,20 €
El-38-D0-295 3,5 m cable for mains power supply 1 2,10 €
Op-40-D0-582 2 auxiliary microswitches with cable 1 28,48 €
Op-37-D0-466 Lithium battery 1 23,96 €
Cost is increased of 20% for quantities smaller than standard box quantity
Price list 2017Apply your discount to obtain your net prices
SCA-19 & Ino 20 Valves Options
Options
Code DescriptionQty per
boxUnit price Net price
Op-40-D0-582 2 auxiliary microswitches with cableNeedle screw mixing device
Op-32-T1-546
Page 10 de 44
VK0041
6 – PIECES DE RECHANGE
Joints de culasse (1 kit) Kj-34-E0-515 (VK2253)
culasse n°1 : Co – 33 – T1 – 05 blanc (VK2111-1)
culasse n°3 : Co – 33 – T1 – 07 orange (VK2111-3) culasse n°5 : Co – 33 – T1 – 09 vert (VK2111-5)
culasse n°7 : Co – 33 – T1 – 11 violet (VK2111-7)
couvre culasse Ca – 33 – T1 - 03 (VK2254)
Kit piston et tiges (VK2194) Kp-40-D0 -634
Joints principaux (1 kit) Kj - 34 - E0 - 516 (VK2066)
raccord de saumurage Kr – 40 - D0 - 525 (VK2265)
Mitigeur
Km – 40 - D0 - 526 (VK2257)Plaque piston
Ka – 40 - D0 - 524 VK2258
Joints de saumurage
Kj - 34 - E0 - 517 (VK2113) Kit joints et entretoises nouveau
Ke-40-D0-635 (VK2114)
11
VK2058
Kj-34-E0-520 Kj-34-E0-521
Brine seals kitKj-34-E0-517
Tank seal O-ring tube seal Ø 25 mm (x5)
Bypass kit Kb-40-D0-540
Inlet outlet seal kit (x5) Interface seal kit (x5)
New Main seals & spacers kit
Price list 2016-2Apply your discount to obtain your net prices
Kj-34-E0-518 Kj-34-E0-519
Breech seals kitKj-34-E0-515 Ke-40-D0-635
Page 14 de 40
VK2113
Kj-34-E0-520 Kj-34-E0-521
Brine seals kitKj-34-E0-517
Tank seal O-ring tube seal Ø 25 mm (x5)
Bypass kit Kb-40-D0-540
Inlet outlet seal kit (x5) Interface seal kit (x5)
New Main seals & spacers kit
Price list 2016-2Apply your discount to obtain your net prices
Kj-34-E0-518 Kj-34-E0-519
Breech seals kitKj-34-E0-515 Ke-40-D0-635
Page 14 de 40
VK2114
Kj-34-E0-520 Kj-34-E0-521
Brine seals kitKj-34-E0-517
Tank seal O-ring tube seal Ø 25 mm (x5)
Bypass kit Kb-40-D0-540
Inlet outlet seal kit (x5) Interface seal kit (x5)
New Main seals & spacers kit
Price list 2016-2Apply your discount to obtain your net prices
Kj-34-E0-518 Kj-34-E0-519
Breech seals kitKj-34-E0-515 Ke-40-D0-635
Page 14 de 40
VK2116
Kj-34-E0-520 Kj-34-E0-521
Brine seals kitKj-34-E0-517
Tank seal O-ring tube seal Ø 25 mm (x5)
Bypass kit Kb-40-D0-540
Inlet outlet seal kit (x5) Interface seal kit (x5)
New Main seals & spacers kit
Price list 2016-2Apply your discount to obtain your net prices
Kj-34-E0-518 Kj-34-E0-519
Breech seals kitKj-34-E0-515 Ke-40-D0-635
Page 14 de 40
VK2117 Kj-34-E0-520 Kj-34-E0-521
Brine seals kitKj-34-E0-517
Tank seal O-ring tube seal Ø 25 mm (x5)
Bypass kit Kb-40-D0-540
Inlet outlet seal kit (x5) Interface seal kit (x5)
New Main seals & spacers kit
Price list 2016-2Apply your discount to obtain your net prices
Kj-34-E0-518 Kj-34-E0-519
Breech seals kitKj-34-E0-515 Ke-40-D0-635
Page 14 de 40
VK2118
Op-40-D0-512 ¾’’ Standard BSP connector 1 8,67 € Op-40-D0-556 ¾’’ Female brass connector 1 27,83 € Op-40-D0-513 ¾’’ Analysis taps connector 1 17,39 € Op-40-D0-572 1’’ Standard BSP connector 1 11,74 € Op-40-D0-593 1" Elbow multi position BSP connector 1 14,97 €
Kb-40-D0-514 Bypass 1 19,91 € Cost is increased of 20% for quantities smaller than standard box quantity
Price list 2016-2Apply your discount to obtain your net prices
SCA-19 & Ino 20 Valves Connectors
Connectors (assembled on the valve)
Bypass (assembled on the valve)
Code Description Qty per box Unit price Net price
Page 9 de 40
VK0042-1 VK0042-2 VK0044
VK0043 VK0043-1 VK0045
Op-40-D0-512 ¾’’ Standard BSP connector 1 8,67 € Op-40-D0-556 ¾’’ Female brass connector 1 27,83 € Op-40-D0-513 ¾’’ Analysis taps connector 1 17,39 € Op-40-D0-572 1’’ Standard BSP connector 1 11,74 € Op-40-D0-593 1" Elbow multi position BSP connector 1 14,97 €
Kb-40-D0-514 Bypass 1 19,91 € Cost is increased of 20% for quantities smaller than standard box quantity
Price list 2016-2Apply your discount to obtain your net prices
SCA-19 & Ino 20 Valves Connectors
Connectors (assembled on the valve)
Bypass (assembled on the valve)
Code Description Qty per box Unit price Net price
Page 9 de 40
ATTACCHI IN-OUT VK20/ VK20 IN-OUT CONNECTORS
VK20 - 1”HYK-VALVES
TABELLE EIETTORI / INJECTOS TABLES
DC
-C-0
18-R
05
Down-flow standard settings for 120 grams of salt per resin liter
Tank Breech Cycle 1 Cycle 2 Cycle 3 Cycle 4
Dimmensions
Volume BackwashBrining(draw)
Slowrince
Rapidrince
Tank refill
Tank Resin Brine Salt Time Flow Time Flow Time Time Volume Time
(L) (L) (L) (Kg) (mn) (L/mn) (mn) (L/mn) (mn) (mn) (L) (mn)
6 x18 6,8 4,5 1,68 0,54 1 4 0,5 3,9 0,84 12 3 1,50 1,5
6 x 35 14 9,5 3,56 1,14 1 4 0,5 7,6 0,84 23 4 3,17 3,2
7 x 35 20 13 4,88 1,56 3 5 0,75 7 1,29 21 4 4,33 4,3
8 x 35 25 17 6,19 1,98 3 6 0,75 8,8 1,29 26 4 5,50 5,5
9 x 35 31 21 7,77 2,49 5 6 1 8,3 1,89 25 5 6,91 6,9
10 x 35 39 25 9,55 3,06 5 7 1 10,1 1,89 30 5 8,49 8,5
10 x 44 50 33 12,25 3,92 7 7 1,2 10,7 2,37 32 5 10,89 10,9
12 x 48 78 51 19,31 6,18 7 8 1,2 16,6 2,37 50 5 17,16 17,2
Tank Breech Cycle 1 Cycle 2 Cycle 3 Cycle 4
Dimmensions
VolumeBrining(draw)
Slowrince
BackwashRapidrince
Tank refill
Tank Resin Brine Salt Flow Time Flow Temps Time Time Volume Time
(L) (L) (L) (Kg) (L/mn) (mn) (L/mn) (mn) (mn) (mn) (L) (mn)
7 x 35 20 13 4,88 1,56 1 0,5 10,3 0,84 31 6 5 4,33 4,3
8 x 35 25 17 6,19 1,98 1 0,5 12,9 0,84 39 8 5 5,50 5,5
9 x 35 31 21 7,77 2,49 3 0,75 10,9 1,29 33 9 5 6,91 6,9
10 x 35 39 25 9,55 3,06 3 0,75 13,2 1,29 40 10 5 8,49 8,5
10 x 44 50 33 12,25 3,92 5 1 12,8 1,89 38 10 6 10,89 10,9
12 x 48 78 51 19,31 6,18 5 1 19,8 1,89 59 10 6 17,16 17,2
13 x 54 104 69 25,74 8,24 7 1,2 22,0 2,37 66 10 8 22,88 22,9
14 x 65 154 102 38,12 12,2 7 1,2 32,3 2,37 97 14 8 33,88 33,9
Up-flow standard settings for 120 grams of salt per resin liter
Nota: these values are only setting indications to apply to softeners with SCA-19 valve. They are determined for standard resin use and for an average temperature of 15°C. They must be adapted in accordance with the specifical installation location data. In any case, they involve Cappers’ responsability.
SCA-19 ModelStandard settings
Breech n°1 Breech n°3 Breech n°5 Breech n°7
Soft
en
er
Co
ntr
ol
Ad
van
ce
Cappers S.A.SZ.I. de Feletrue Edouard Michelin63300 Thiers - FranceTel : +33(0)4 73 94 84 87
VK2111-1VK2111-3
VK2111-5
VK2111-7
Iniettore 1/ Injector 1 Iniettore 3/ Injector 3 Iniettore 5/ Injector 5 Iniettore 7/ Injector 7
Impostazioni DOWN-FLOW basate su 120 g di sale per litro di resina DOWN-FLOW standard settings for 120 g of salt per litre of resin.
DC
-C-0
18-R
05
Down-flow standard settings for 120 grams of salt per resin liter
Tank Breech Cycle 1 Cycle 2 Cycle 3 Cycle 4
Dimmensions
Volume BackwashBrining(draw)
Slowrince
Rapidrince
Tank refill
Tank Resin Brine Salt Time Flow Time Flow Time Time Volume Time
(L) (L) (L) (Kg) (mn) (L/mn) (mn) (L/mn) (mn) (mn) (L) (mn)
6 x18 6,8 4,5 1,68 0,54 1 4 0,5 3,9 0,84 12 3 1,50 1,5
6 x 35 14 9,5 3,56 1,14 1 4 0,5 7,6 0,84 23 4 3,17 3,2
7 x 35 20 13 4,88 1,56 3 5 0,75 7 1,29 21 4 4,33 4,3
8 x 35 25 17 6,19 1,98 3 6 0,75 8,8 1,29 26 4 5,50 5,5
9 x 35 31 21 7,77 2,49 5 6 1 8,3 1,89 25 5 6,91 6,9
10 x 35 39 25 9,55 3,06 5 7 1 10,1 1,89 30 5 8,49 8,5
10 x 44 50 33 12,25 3,92 7 7 1,2 10,7 2,37 32 5 10,89 10,9
12 x 48 78 51 19,31 6,18 7 8 1,2 16,6 2,37 50 5 17,16 17,2
Tank Breech Cycle 1 Cycle 2 Cycle 3 Cycle 4
Dimmensions
VolumeBrining(draw)
Slowrince
BackwashRapidrince
Tank refill
Tank Resin Brine Salt Flow Time Flow Temps Time Time Volume Time
(L) (L) (L) (Kg) (L/mn) (mn) (L/mn) (mn) (mn) (mn) (L) (mn)
7 x 35 20 13 4,88 1,56 1 0,5 10,3 0,84 31 6 5 4,33 4,3
8 x 35 25 17 6,19 1,98 1 0,5 12,9 0,84 39 8 5 5,50 5,5
9 x 35 31 21 7,77 2,49 3 0,75 10,9 1,29 33 9 5 6,91 6,9
10 x 35 39 25 9,55 3,06 3 0,75 13,2 1,29 40 10 5 8,49 8,5
10 x 44 50 33 12,25 3,92 5 1 12,8 1,89 38 10 6 10,89 10,9
12 x 48 78 51 19,31 6,18 5 1 19,8 1,89 59 10 6 17,16 17,2
13 x 54 104 69 25,74 8,24 7 1,2 22,0 2,37 66 10 8 22,88 22,9
14 x 65 154 102 38,12 12,2 7 1,2 32,3 2,37 97 14 8 33,88 33,9
Up-flow standard settings for 120 grams of salt per resin liter
Nota: these values are only setting indications to apply to softeners with SCA-19 valve. They are determined for standard resin use and for an average temperature of 15°C. They must be adapted in accordance with the specifical installation location data. In any case, they involve Cappers’ responsability.
SCA-19 ModelStandard settings
Breech n°1 Breech n°3 Breech n°5 Breech n°7
Soft
en
er
Co
ntr
ol
Ad
van
ce
Cappers S.A.SZ.I. de Feletrue Edouard Michelin63300 Thiers - FranceTel : +33(0)4 73 94 84 87
Nota: i valori sopra indicati sono riferiti esclusivamente ad addolcitori con valvole VK20 e sono riferiti a test eseguiti su resina standard ad una tem-peratura media di 15 ° C. I dati possono variare in riferimento alle caratteristiche specifiche dell’ impianto dove vengono montate le valvole VK20. In ogni caso la tabella sopra è indicativa ed esonera Hytek da ogni responsabilità.Note: These values are only setting indications applicable to softeners with VK20 valves. They are determined for standard resin use and for an av-erage temperature of 15°C. They must be adapted in accordance with the specific location of every installation. In any case they do not involve Hytek’s responsability.
Impostazioni UP-FLOW basate su 120 g di sale per litro di resina UP-FLOW standard settings for 120 g of salt per litre of resin.
DC
-C-0
18-R
05
Down-flow standard settings for 120 grams of salt per resin liter
Tank Breech Cycle 1 Cycle 2 Cycle 3 Cycle 4
Dimmensions
Volume BackwashBrining(draw)
Slowrince
Rapidrince
Tank refill
Tank Resin Brine Salt Time Flow Time Flow Time Time Volume Time
(L) (L) (L) (Kg) (mn) (L/mn) (mn) (L/mn) (mn) (mn) (L) (mn)
6 x18 6,8 4,5 1,68 0,54 1 4 0,5 3,9 0,84 12 3 1,50 1,5
6 x 35 14 9,5 3,56 1,14 1 4 0,5 7,6 0,84 23 4 3,17 3,2
7 x 35 20 13 4,88 1,56 3 5 0,75 7 1,29 21 4 4,33 4,3
8 x 35 25 17 6,19 1,98 3 6 0,75 8,8 1,29 26 4 5,50 5,5
9 x 35 31 21 7,77 2,49 5 6 1 8,3 1,89 25 5 6,91 6,9
10 x 35 39 25 9,55 3,06 5 7 1 10,1 1,89 30 5 8,49 8,5
10 x 44 50 33 12,25 3,92 7 7 1,2 10,7 2,37 32 5 10,89 10,9
12 x 48 78 51 19,31 6,18 7 8 1,2 16,6 2,37 50 5 17,16 17,2
Tank Breech Cycle 1 Cycle 2 Cycle 3 Cycle 4
Dimmensions
VolumeBrining(draw)
Slowrince
BackwashRapidrince
Tank refill
Tank Resin Brine Salt Flow Time Flow Temps Time Time Volume Time
(L) (L) (L) (Kg) (L/mn) (mn) (L/mn) (mn) (mn) (mn) (L) (mn)
7 x 35 20 13 4,88 1,56 1 0,5 10,3 0,84 31 6 5 4,33 4,3
8 x 35 25 17 6,19 1,98 1 0,5 12,9 0,84 39 8 5 5,50 5,5
9 x 35 31 21 7,77 2,49 3 0,75 10,9 1,29 33 9 5 6,91 6,9
10 x 35 39 25 9,55 3,06 3 0,75 13,2 1,29 40 10 5 8,49 8,5
10 x 44 50 33 12,25 3,92 5 1 12,8 1,89 38 10 6 10,89 10,9
12 x 48 78 51 19,31 6,18 5 1 19,8 1,89 59 10 6 17,16 17,2
13 x 54 104 69 25,74 8,24 7 1,2 22,0 2,37 66 10 8 22,88 22,9
14 x 65 154 102 38,12 12,2 7 1,2 32,3 2,37 97 14 8 33,88 33,9
Up-flow standard settings for 120 grams of salt per resin liter
Nota: these values are only setting indications to apply to softeners with SCA-19 valve. They are determined for standard resin use and for an average temperature of 15°C. They must be adapted in accordance with the specifical installation location data. In any case, they involve Cappers’ responsability.
SCA-19 ModelStandard settings
Breech n°1 Breech n°3 Breech n°5 Breech n°7
Soft
en
er
Co
ntr
ol
Ad
van
ce
Cappers S.A.SZ.I. de Feletrue Edouard Michelin63300 Thiers - FranceTel : +33(0)4 73 94 84 87
Nota: i valori sopra indicati sono riferiti esclusivamente ad addolcitori con valvole VK20 e sono riferiti a test eseguiti su resina standard ad una tem-peratura media di 15 ° C. I dati possono variare in riferimento alle caratteristiche specifiche dell’ impianto dove vengono montate le valvole VK20. In ogni caso la tabella sopra è indicativa ed esonera Hytek da ogni responsabilità.Note: These values are only setting indications applicable to softeners with VK20 valves. They are determined for standard resin use and for an av-erage temperature of 15°C. They must be adapted in accordance with the specific location of every installation. In any case they do not involve Hytek’s responsability.
VK20 - 1” HYK-VALVES
DIAGRAMMI DI FLUSSO VK20 / VK20 FLOW DIAGRAMS
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
bars
bars
bars
bars
bars
bars
bars
bars
bars
bars
bars
bars
l/mn
l/mn
l/mn
l/mn
l/mn
l/mn
l/mn
l/mn
l/mn
l/mn
l/mn
l/mn
0,25
0,25
0,25
0,25
1
1
1
1
0,50
0,50
0,50
0,50
2
2
2
2
0,75
0,75
0,75
0,75
3
3
3
3
1,00
1,00
1,00
1,00
4
4
4
4
1,25
1,25
1,25
1,25
5
5
5
5
1,50
1,50
1,50
1,50
6
6
6
6
1,75
1,75
1,75
1,75
7
7
7
7
0,50
0,50
0,50
0,50
0,75
0,75
0,75
0,75
1,00
1,00
1,00
1,00
1,25
1,25
1,25
1,25
1,50
1,50
1,50
1,50
1,75
1,75
1,75
1,75
2,00
2,00
2,00
2,00
2,25
2,25
2,25
2,25
2,50
2,50
2,50
2,50
Aspiration de saumure
Aspiration de saumure
Aspiration de saumure
Aspiration de saumure
Rinçage lent
Rinçage lent
Rinçage lent
Rinçage lent
Détassage/rinçage rapide
Détassage/rinçage rapide
Détassage/rinçage rapide
Détassage/rinçage rapide
Culasse n°1
Culasse n°3
Culasse n°5
Culasse n°7
SCA19 - Courbes de débitsIniettore 1/ Injector 1
Iniettore 3/ Injector 3
Iniettore 5/ Injector 5
Iniettore 7/ Injector 7
Aspirazione salamoia/ Brine suction Lavaggio lento/ Slow rinse Control.- R.Rapido/Backwash - R.Rinse
Aspirazione salamoia/ Brine suction Lavaggio lento/ Slow rinse Control.- R.Rapido/Backwash - R.Rinse
Aspirazione salamoia/ Brine suction Lavaggio lento/ Slow rinse Control.- R.Rapido/Backwash - R.Rinse
Aspirazione salamoia/ Brine suction Lavaggio lento/ Slow rinse Control.- R.Rapido/Backwash - R.Rinse
VK32 - 1”1/4
VK32- Materiale del corpo valvola: _______________________ Noryl ® - Entrata / Uscita: _________________________________ 1 ¼ “ BSPPortata Valvola sola- In continuo (Dp = 1,0 bar): ________________________ 9,04 m3/h - Valore massimo (Dp = 1,7 bar): __________________ 11,8 m3/h- Contolav. (Dp = 1,0 bar): ________________________ 9,04 m3/h- Contolav. max (Dp = 1,7 bar): ___________________ 11,8 m3/hMicroprocessore- Visualizzazione: ____ display digitale retro illuminato, 4, 5 cifre- Salvaguardia parametri: ___ Back-up tramite condensatore- Relè Esterno: ___________________________ Opzionale (VK0200)- Alimentazione elettrica:* VK32-1: _______________________________ 230 V / 5V – 1A – DC * VK32-2 & * VK32-3: __________________ 230 V / 7,5V – 2 A – DC - Parametri impostabili: Ora del giorno, ora di rigenerazione, tempi dei cicli, capacità ciclica, forzatura a tempo, riserva. - Lettura: Volume restante, defalco del tempo, posizione del ciclo in corso.- Rigenerazione: a giorni fissi, a giorni selezionabili, volumetrica ritardata o immediata, manuale- Modalità Rigenerazione: Up Flow, Down Flow, Filtro, Salamoia variabileCaratteristiche:- Rigenerazione DF & UF senza costi aggiuntivi- Regolazione dei Cicli- Riempimento vasca sale con acqua addolcita (solo UF)- Salamoia variabile- Movimentazione pistone con sensore ottico e micro AUX- Manutenzione semplificata (iniettori, regolatori scarico etc)- Rapida connessione alla linea di scarico- Facile disassemblaggio del corpo dall’ adattatore - Contatore integrato- Miscelatore della durezza integrato - Versione Duplex & Multiplex tramite intefaccia WiFi con ges-tione di 2,3,4 o 5 valvole- Programma statistico fino alle ultime 4 rigenerazioni- Possibilità di funzionamento tramite contatore esternoDimensioni- Tubo distributore: _________________________________ 32 mm - Altezza tubo distributore sopra la bombola: _______ +/- 5 mm- Conduttura allo scarico: ___________________ 1/2” o 3/4” o 1” - Conduttura alla salamoia: _____________________ 3/8” o 1/2”- Filettatura bombola: _____ 4” - 8 NPSM (opzione 2 ½” - 8 NPSM)- Altezza: __________________________________________ 269 mm- Larghezza: _______________________________________ 325 mm- Profondità: _______________________________________ 221 mm- Peso: ______________________________________________ 3.25 kgBombole utilizzabili- Addolcitore: ____________________________________Ø 12”- 21”- Filtri:_____________________________________________Ø 12” - 21” - Volume resina: _____________________________ da 50 lt a 225 ltPressione- Idrostatica: ________________________________________ 24 bar- Servizio: _________________________________________ 2 a 8 bar- Temperatura: ____________________________________1 a 45°C- Test pressione: __ 1-14 bar (250.00 cicli), 1-24 bar (70.000 cicli) Opzioni- Relè Esterno (VK0200)- Acqua Calda - Valvola filtro- SBV di sicurezza- Attacco Side MountCertificati- Conformità Regolamento CE bassa tensione- CE - RoHS- ACS : 13 ACC LY 805
HYK-VALVESSCARICO
Drain
MISCELATOREMixing
ACCESSO EIETTOREAccess Injector
CAVO METERMeter Cable
LINEA SALAMOIABrine Line
VITI DI FISSAGGIO BASEBase Retaining Screws
INGRESSOInlet
USCITAOutlet
VK32- Valve material: ____________________________________ Noryl ®- Inlet / outlet:_____________________________________ 1 ¼ “ BSPFlow rate valve alone- Continuous (1,0 bar drop): _______________________ 9,04 m3/h - Peak (1,7 bar drop): _____________________________ 11,8 m3/h- Backwash (1,0 bar drop): ________________________ 9,04 m3/h- Max backwash (1,7 bar drop): ___________________ 11,8 m3/hMicroprocessor- Display: _________________ Large backlight display - 4, 5 digits- Parameter backup: ____________________ Back-up Capacitor - External relay : ___________________________ Optional (VK0200)- Power supply:* VK32-1: _______________________________ 230 V / 5V – 1A – DC * VK32-2 & * VK32-3: __________________ 230 V / 7,5V – 2 A – DC - Adjustable parameters: time of day, time of regeneration, cycles time, cyclical capacity, time forcing, reserve.- Reading: volume remaining, remaining time, cycle in pro-gress.- Regeneration: Hours, Timeclock, Meter delayed or immedi-ate, manual.- Regeneration Mode: Downflow / Upflow, Filter, Variable brin-ingGeneral Features:- DF & UF rigeneration without additional costs- Adjustable cicles- Brine fill with softened water (only UF)- Variable Brining- Piston movement with optical sensor and micro AUX- Easier maintenance (injectors, flow regulators, etc)- Quick connexion to the drain line - Easy disassembly of the body from the adaptor- Integrated meter- Integrated mixing device- Duplex & Multiplex version by Wireless connexion of 2, 3, 4 or 5 control valves- Diagnostic programm up to the last 4 rigenerations- Possibility to working with external flow meterDimensions:- Distributor pilot: ____________________________________ 32 mm- Length above the tank: __________________________ +/- 5 mm- Drain line: __________________________________1/2” o 3/4” o 1” - Brine line: ______________________________________ 3/8” o 1/2”- Mounting base: ___________ 4” - 8 NPSM (option 2 ½” - 8 NPSM)- Height: ___________________________________________ 269 mm- Width: ____________________________________________ 325 mm - Depth: ____________________________________________ 221 mm- Weight: _____________________________________________ 3.25 kgTanks Size application (recommended) - Water softener: __________________________________Ø 12” - 21”- Filter: ____________________________________________Ø 12” - 21” - Resin volume: _________________________ from 50 lt up to 225 ltPressure- Hydrostatic:_______________________________________ 24 bar- Working:________________________________________ 2 to 8 bar- Temperature:____________________________________1 to 45°C- Pressure Test:_1-14 bar (250.00 cycles), 1-24 bar (70.000 cycles) Options- External Relay (VK0200) - Hot Water- Filter valve- SBV Safety brine Valve- Side Mount adapterCertificates- Compliant to CE low voltage regulations - CE - RoHS- ACS : 13 ACC LY 805
DIMENSIONI VK32-1/ VK32-1 DIMENSIONS
HYK-VALVESVK32 - 1”1/4
105
217
118,4
100
102,7
59
245
Dessus de bouteille
canule pour tube Ø 13 mm
326
51,50
103
148
filetage 1¼'' BSPcylindrique
91
107
filetage 2½'' NPSM
Raccord rapideØ 3/8'' (9,52 mm)
Tube distributeur: Ø 32 mmlongueur tube: raz de bouteille ± 3 mm
SCHEMI DI FLUSSO VK32-1/ VK32-1 FLOW DIAGRAMS
IN OUT
ValvolaBackpressure
A
S
Aspirazione/Suction
Servizio Down Flow / Down Flow Service
Eiettore / Injector
Scarico/DrainS
A Aspirazione/Suction
Ingreso/Inlet
Uscita/ Outlet
Salamoia/ Brine
Check Ball
OUT
ValvolaBackpressure
A
S
IN
Scarico/DrainS
A Aspirazione/Suction
Aspirazione/Suction
1 - Controlavaggio / Backwash
Eiettore / Injector
Ingreso/Inlet
Uscita/ Outlet
Salamoia/ Brine
Check Ball
S
A
IN OUT
ValvolaBackpressure
Scarico/DrainS
A Aspirazione/Suction
2 - Aspirazione salamoia / Brine SuctionIngreso/Inlet
Uscita/ Outlet
Salamoia/ Brine
Aspirazione/Suction
Eiettore / Injector
Check Ball
IN OUT
ValvolaBackpressure
A
SScarico/DrainS
A Aspirazione/Suction
3 - Risciacquo Rapido / Rapid RinseIngreso/Inlet
Uscita/ Outlet
Salamoia/ BrineEiettore / Injector
Aspirazione/Suction
Check Ball
IN
ValvolaBackpressure
A
S
OUT
Scarico/DrainS
A Aspirazione/Suction
4 - Riempimento / Brine RefillIngreso/Inlet
Uscita/ Outlet
Salamoia/ BrineEiettore / Injector
Aspirazione/Suction
Check BallCheck Ball
Check Ball
HYK-VALVES VK32 - 1”1/4
POS. COD. DESCRIZIONE/DESCRIPTION
1 VK2255 Actuator kit - main piston
2 VK2180 Piston plate kit 125 (1 set) - VK32
3 VK2155 Main piston 125 - VK32
4 VK2085 Main seals and spacers kit (1 set) - 125
5 VK2231 Valve body
6 VK2311 2 ½" Threaded tank adaptor
7 VK2234 VAS Plate -125 - VK32-1
8 VK2235 Assembled brine valve body 3/8"
9 VK2195 Electronic and housing assembly (7,5 Volts 2A)
10 VK2245 Assembled brine valve elbow
11 VK2240 Brine valve cover
12 VK2313 Drain Retainer
13
- VK2296 0,8 m3/h DFR 13 mm outlet
- VK2297 1,1 m3/h DFR 13 mm outlet
- VK2298 1.6 m3/h DFR 13 mm outlet
- VK2299 0,8 m3/h DFR 19 mm outlet
- VK2300 1,1 m3/h DFR 19 mm outlet
- VK2301 1.6 m3/h DFR 19 mm outlet
- VK2302 0,8 m3/h DFR 3/4'' BSP outlet
- VK2303 1,1 m3/h DFR 3/4'' BSP outlet
- VK2304 1,6 m3/h DFR 3/4'' BSP outlet
- VK2305 2,3 m3/h DFR 1'' BSP outlet
- VK2306 3,3 m3/h DFR 1'' BSP outlet
- VK2307 5,2 m3/h DFR 1'' BSP outlet
- VK2308 7,0 m3/h DFR 1'' ¼ BSP outlet
14 VK2232 Cylinder head with plug on injector (all models)
15
- VK2309 1 ¼" connector kit for chrono valves
- VK2310 1 ¼" connector kit with turbine meter
VK 32-1
Drain line Flow control available:
In-Outlet connectors 1¼''
RICAMBI VK32-1/ VK32-1 SPARE PARTS
CHEMI DI FLUSSO VK32-2/ VK32-2 FLOW DIAGRAMS
HYK-VALVESVK32 - 1”1/4
DIMENSIONI VK32-2/ VK32-2 DIMENSIONS
78,36
filetage 2½'' NPSM
Raccord rapideØ 1/2'' (12,7 mm)
Tube distributeur: Ø 32 mmlongueur tube: raz de bouteille ± 3 mm
245
118 103
106
217
suivant versions3/4'' BSP1'' BSP1¼'' BSP
103
51,5
270
filetage 1¼'' BSPcylindrique
Dessus de bouteille
ValvolaBackpressure
Scarico/DrainS
A Aspirazione/Suction
IN OUT
S
A
Aspirazione/Suction
Servizio Down Flow / Down Flow Service
Eiettore / Injector
Ingreso/Inlet
Uscita/ Outlet
Salamoia/ Brine
Check Ball
ValvolaBackpressure
IN
A
Aspirazione/Suction
S
Scarico/DrainS
A Aspirazione/Suction
Controlavaggio / Backwash
Salamoia/ Brine
Ingreso/Inlet
Uscita/ Outlet
Eiettore / Injector
Check Ball
ValvolaBackpressure
AAspirazione
S
OUTIN
Scarico/DrainS
A Aspirazione/Suction
Aspirazione / Brine Suction
Salamoia/ Brine
Ingreso/Inlet
Uscita/ Outlet
Check Ball
ValvolaBackpressure
IN
S
A
Scarico/DrainS
A Aspirazione/Suction
Risciacquo Rapido / Rapid Rinse
Salamoia/ Brine
Ingreso/Inlet
Uscita/ OutletAspirazione/
Suction
Eiettore / Injector
Check Ball
A
Aspirazione/Suction
S
OUTIN
Scarico/DrainS
A Aspirazione/Suction
4 - Riempimento / Brine Refill
Salamoia/ Brine
Ingreso/Inlet
Uscita/ Outlet
ValvolaContropressione/
Backpressure Valve
Eiettore / Injector
Check Ball
POS. COD. DESCRIZIONE/DESCRIPTION
1 VK2255 Actuator kit - main piston
2 VK2180 Piston plate kit 125 (1 set) - VK32
3 VK2155 Main piston 125 - VK32
4 VK2085 Main seals and spacers kit (1 set) - 125
5 VK2231 Valve body
6 VK2311 2 ½" Threaded tank adaptor
7 VK2233 Blind Plate - 125
8 VK2195 Electronic and housing assembly (7,5 Volts 2A)
9 VK2232 Cylinder head with plug on injector (all models)
10 VK2252 Motorized Brine valve 1/2"
11 VK2313 Drain Retainer
12
- VK2296 0,8 m3/h DFR 13 mm outlet
- VK2297 1,1 m3/h DFR 13 mm outlet
- VK2298 1.6 m3/h DFR 13 mm outlet
- VK2299 0,8 m3/h DFR 19 mm outlet
- VK2300 1,1 m3/h DFR 19 mm outlet
- VK2301 1.6 m3/h DFR 19 mm outlet
- VK2302 0,8 m3/h DFR 3/4'' BSP outlet
- VK2303 1,1 m3/h DFR 3/4'' BSP outlet
- VK2304 1,6 m3/h DFR 3/4'' BSP outlet
- VK2305 2,3 m3/h DFR 1'' BSP outlet
- VK2306 3,3 m3/h DFR 1'' BSP outlet
- VK2307 5,2 m3/h DFR 1'' BSP outlet
- VK2308 7,0 m3/h DFR 1'' ¼ BSP outlet
13
- VK2309 1 ¼" connector kit for chrono valves
- VK2310 1 ¼" connector kit with turbine meter
VK 32-2
Drain line Flow control available:
In-Outlet connectors 1¼''
RICAMBI VK32-2/ VK32-2 SPARE PARTS
HYK-VALVES VK32 - 1”1/4
TABELLE EIETTORI / INJECTOS TABLES
Down-flow standard settings for 120 g of salt per litre of resin
Valve Tank
Inje
ctor
Salt
Cycle
1
Cycle
2
Cycle
3
Cycle
4
Wat
er u
se
Ba
ckw
ash
Brin
ing
(dra
w)
Slow
rins
e
Rapi
d rin
se
Tank
refil
l
VK32
-1
VK32
-2
VK40
-1
VK40
-2
VK50
-2
Dim
ensio
ns
Volu
me
(L)
Open
ing
Resin
(L)
Inje
ctor
n°
Salt
volu
me
(kg)
Brin
e vo
lum
e
Tim
e
Flow
Tim
e
Flow
Tim
e dr
aw +
slow
rins
e
Tim
e
Volu
me
Tim
e
Flow
DFR
m³/
h
12 X 48 79 2½'' 55 1 6,6 20,6 5 1,9 10,9 1,8 33 5 18,3 4,6 0,8 210 14 X 52 115 2½'' 75 2 9 28,1 5 2,4 11,7 3,3 35 5 25,0 6,3 1,1 324 14 X 65 148 2½'' or 4'' 100 2 12 37,5 5 2,4 15,6 3,3 47 5 33,3 8 1,1 371
16 X 65 194 2½'' or 4'' 125 3 15 46,9 5 4,0 11,7 4,5 35 5 41,7 10 1,6 466
16 X 65 194 2½'' or 4'' 125 3 15 46,9 5 4,0 11,7 4,5 35 5 41,7 4 1,6 466 18 X 65 257 4'' 170 3 20 63,8 8 4,0 15,9 4,5 48 6 56,7 6 1,6 645 21 X 62 330 4'' 220 4 35 110,0 5 5 97,8 10 2,3
24 X 72 473 4'' 310 5 50 155,0 5 5 137,8 14 3,3
30 X 72 697 4'' 460 6 74 230,0 5 5 204,4 20 5,2
36 X 72 1011 4'' 700 7 112 350,0 5 5 311,1 31 7,0
Note: These values are only setting indications applicable to softeners with VK valves. They are determined for standard resin use and for an
average temperature of 15°C. They must be adapted in accordance with the specific location of every installation. In any case they do not involve Hytek’s responsibility.
Injector
Drain flow regulator (DFR) Range
Cappers | Tel : +33 (0) 473 94 84 87 | www.cappers.fr
Down- litre of resin
Valve Tank
Inje
ctor
Salt
Cycle
1
Cycle
2
Cycle
3
Cycle
4
Wat
er u
se
Back
was
h
Brin
ing
(dra
w)
Slow
rins
e
Rapi
d rin
se
Tank
refil
l
VK32
-1
VK32
-2
VK40
-1
VK40
-2
VK50
-2
Dim
ensio
ns
Volu
me
(L)
Open
ing
Resin
(L)
Inje
ctor
n°
Salt
volu
me
(kg)
Brin
e vo
lum
e
Tim
e
Flow
Tim
e
Flow
Tim
e dr
aw +
slow
rins
e
Tim
e
Volu
me
Tim
e
Flow
DFR
m³/
h
12 X 48 79 2½'' 55 1 8,8 27,5 5 1,9 14,5 1,8 43 5 24,4 6,1 0,8 236 14 X 52 115 2½'' 75 2 12 37,5 5 2,4 15,6 3,3 47 5 33,3 8,3 1,1 371 14 X 65 148 2½'' or 4'' 100 2 16 50,0 5 2,4 20,8 3,3 63 5 44,4 11 1,1 434
16 X 65 194 2½'' or 4'' 125 3 20 62,5 5 4,0 15,6 4,5 47 5 55,6 14 1,6 533
16 X 65 194 2½'' or 4'' 125 3 20 62,5 5 4,0 15,6 4,5 47 5 55,6 6 1,6 533 18 X 65 257 4'' 170 3 27 85,0 8 4,0 21,3 4,5 64 6 75,6 8 1,6 736 21 X 62 330 4'' 220 4 35 110,0 5 5 97,8 10 2,3
24 X 72 473 4'' 310 5 50 155,0 5 5 137,8 14 3,3
30 X 72 697 4'' 460 6 74 230,0 5 5 204,4 20 5,2
36 X 72 1011 4'' 700 7 112 350,0 5 5 311,1 31 7,0
Note: These values are only setting indications applicable to softeners with Cappers valves. They are determined for standard resin use and for an average temperature of 15°C. They must be adapted in accordance with the specific location of every installation. In any case they do not involve Cappers’ responsibility.
Drain flow regulator (DFR) Range
Injector
Down-flow standard settings for 120 g of salt per litre of resin
Valve Tank
Inje
ctor
Salt
Cycle
1
Cycle
2
Cycle
3
Cycle
4
Wat
er u
se
Back
was
h
Brin
ing
(dra
w)
Slow
rins
e
Rapi
d rin
se
Tank
refil
l
VK32
-1
VK32
-2
VK40
-1
VK40
-2
VK50
-2
Dim
ensio
ns
Volu
me
(L)
Open
ing
Resin
(L)
Inje
ctor
n°
Salt
volu
me
(kg)
Brin
e vo
lum
e
Tim
e
Flow
Tim
e
Flow
Tim
e dr
aw +
slow
rins
e
Tim
e
Volu
me
Tim
e
Flow
DFR
m³/
h
12 X 48 79 2½'' 55 1 6,6 20,6 5 1,9 10,9 1,8 33 5 18,3 4,6 0,8 210 14 X 52 115 2½'' 75 2 9 28,1 5 2,4 11,7 3,3 35 5 25,0 6,3 1,1 324 14 X 65 148 2½'' or 4'' 100 2 12 37,5 5 2,4 15,6 3,3 47 5 33,3 8 1,1 371
16 X 65 194 2½'' or 4'' 125 3 15 46,9 5 4,0 11,7 4,5 35 5 41,7 10 1,6 466
16 X 65 194 2½'' or 4'' 125 3 15 46,9 5 4,0 11,7 4,5 35 5 41,7 4 1,6 466 18 X 65 257 4'' 170 3 20 63,8 8 4,0 15,9 4,5 48 6 56,7 6 1,6 645 21 X 62 330 4'' 220 4 35 110,0 5 5 97,8 10 2,3
24 X 72 473 4'' 310 5 50 155,0 5 5 137,8 14 3,3
30 X 72 697 4'' 460 6 74 230,0 5 5 204,4 20 5,2
36 X 72 1011 4'' 700 7 112 350,0 5 5 311,1 31 7,0
Note: These values are only setting indications applicable to softeners with VK valves. They are determined for standard resin use and for an
average temperature of 15°C. They must be adapted in accordance with the specific location of every installation. In any case they do not involve Hytek’s responsibility.
Injector
Drain flow regulator (DFR) Range
Nota: i valori sopra indicati sono riferiti esclusivamente ad addolcitori con valvole VK e sono riferiti a test eseguiti su resina standard ad una temperatura media di 15 ° C. I dati possono variare in riferimento alle caratteristiche specifiche dell’ impianto dove ven-gono montate le valvole VK. In ogni caso la tabella sopra è indicativa ed esonera Hytek da ogni responsabilità.Note: These values are only setting indications applicable to softeners with VK valves. They are determined for standard resin use and for an average temperature of 15°C. They must be adapted in accordance with the specific location of every installation. In any case they do not involve Hytek’s responsability.
Impostazioni Down-Flow basate su 120 g di sale per litro di resina Down-Flow standard settings for 120 g of salt per litre of resin.
Iniettore/Injector
Impostazioni Down-Flow basate su 160 g di sale per litro di resina Down-Flow standard settings for 160 g of salt per litre of resin.
Nota: i valori sopra indicati sono riferiti esclusivamente ad addolcitori con valvole VK e sono riferiti a test eseguiti su resina standard ad una temperatura media di 15 ° C. I dati possono variare in riferimento alle caratteristiche specifiche dell’ impianto dove ven-gono montate le valvole VK. In ogni caso la tabella sopra è indicativa ed esonera Hytek da ogni responsabilità.Note: These values are only setting indications applicable to softeners with VK valves. They are determined for standard resin use and for an average temperature of 15°C. They must be adapted in accordance with the specific location of every installation. In any case they do not involve Hytek’s responsability.
Tipi di regolatori di scarico (DFR)/Drain flow regulator (DFR)
Down-flow standard settings for 120 g of salt per litre of resin
Valve Tank
Inje
ctor
Salt
Cycle
1
Cycle
2
Cycle
3
Cycle
4
Wat
er u
se
Back
was
h
Brin
ing
(dra
w)
Slow
rins
e
Rapi
d rin
se
Tank
refil
l
VK32
-1
VK32
-2
VK40
-1
VK40
-2
VK50
-2
Dim
ensio
ns
Volu
me
(L)
Open
ing
Resin
(L)
Inje
ctor
n°
Salt
volu
me
(kg)
Brin
e vo
lum
e
Tim
e
Flow
Tim
e
Flow
Tim
e dr
aw +
slow
rins
e
Tim
e
Volu
me
Tim
e
Flow
DFR
m³/
h
12 X 48 79 2½'' 55 1 6,6 20,6 5 1,9 10,9 1,8 33 5 18,3 4,6 0,8 210 14 X 52 115 2½'' 75 2 9 28,1 5 2,4 11,7 3,3 35 5 25,0 6,3 1,1 324 14 X 65 148 2½'' or 4'' 100 2 12 37,5 5 2,4 15,6 3,3 47 5 33,3 8 1,1 371
16 X 65 194 2½'' or 4'' 125 3 15 46,9 5 4,0 11,7 4,5 35 5 41,7 10 1,6 466
16 X 65 194 2½'' or 4'' 125 3 15 46,9 5 4,0 11,7 4,5 35 5 41,7 4 1,6 466 18 X 65 257 4'' 170 3 20 63,8 8 4,0 15,9 4,5 48 6 56,7 6 1,6 645 21 X 62 330 4'' 220 4 35 110,0 5 5 97,8 10 2,3
24 X 72 473 4'' 310 5 50 155,0 5 5 137,8 14 3,3
30 X 72 697 4'' 460 6 74 230,0 5 5 204,4 20 5,2
36 X 72 1011 4'' 700 7 112 350,0 5 5 311,1 31 7,0
Note: These values are only setting indications applicable to softeners with VK valves. They are determined for standard resin use and for an
average temperature of 15°C. They must be adapted in accordance with the specific location of every installation. In any case they do not involve Hytek’s responsibility.
Injector
Drain flow regulator (DFR) Range
Tipi di regolatori di scarico (DFR)/Drain flow regulator (DFR)
HYK-VALVESVK32 - 1”1/4
HYK-VALVES
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
bars
bars
bars
bars
bars
bars
bars
bars
l/mn
l/mn
l/mn
l/mn
l/mn
l/mn
l/mn
l/mn
l/mn
l/mn
2,0
2,0
2,0
2,0
3,0
3,0
3,0
3,0
4,0
4,0
4,0
4,0
5,0
5,0
5,0
5,0
6,0
6,0
6,0
6,0
7,0
7,0
7,0
7,0
8,0
8,0
8,0
8,0
2,0
2,0
2,0
2,0
3,0
3,0
3,0
3,0
4,0
4,0
4,0
4,0
5,0
5,0
5,0
5,0
6,0
6,0
6,0
6,0
7,0
7,0
7,0
7,0
8,0
8,0
8,0
8,0
8,0
8,0
8,0
8,0
9,0
9,0
9,0
9,0
Brine draw Slow rinse
Injector n°1
Injector n°2
Injector n°3
Injector n°4
SCA industrial - Flow diagrams
Slow rinseBrine draw
Slow rinse
Slow rinse
Brine draw
Brine draw
DIAGRAMMI DI FLUSSO / FLOW DIAGRAMS
VK32 - 1”1/4
VK40 - 1”1/2
VK40- Materiale del corpo valvola: _______________________ Noryl ® - Entrata / Uscita: _________________________________ 1“1/2 BSPPortata Valvola sola- In continuo (Dp = 1,0 bar): _____________________ 11,6 m3/h - Valore massimo (Dp = 1,7 bar): __________________ 15,0 m3/h- Contolav. (Dp = 1,0 bar): ________________________ 11,6 m3/h- Contolav. max (Dp = 1,7 bar): ___________________ 15,0 m3/hMicroprocessore- Visualizzazione: ____ display digitale retro illuminato, 4, 5 cifre- Salvaguardia parametri: ___ Back-up tramite condensatore- Relè Esterno: ___________________________ Opzionale (VK0200)- Alimentazione elettrica:* VK40-1: _______________________________ 230 V / 5V – 1A – DC * VK40-2 & * VK40-3: __________________ 230 V / 7,5V – 2 A – DC - Parametri impostabili: Ora del giorno, ora di rigenerazione, tempi dei cicli, capacità ciclica, forzatura a tempo, riserva. - Lettura: Volume restante, defalco del tempo, posizione del ciclo in corso.- Rigenerazione: a giorni fissi, a giorni selezionabili, volumetrica ritardata o immediata, manuale- Modalità Rigenerazione: Up Flow, Down Flow, Filtro, Salamoia variabileCaratteristiche:- Rigenerazione DF & UF senza costi aggiuntivi- Regolazione dei Cicli- Riempimento vasca sale con acqua addolcita (solo UF)- Salamoia variabile- Movimentazione pistone con sensore ottico e micro AUX- Manutenzione semplificata (iniettori, regolatori scarico etc)- Rapida connessione alla linea di scarico- Facile disassemblaggio del corpo dall’ adattatore - Contatore integrato- Miscelatore della durezza integrato - Versione Duplex & Multiplex tramite intefaccia WiFi con ges-tione di 2,3,4 o 5 valvole- Programma statistico fino alle ultime 4 rigenerazioni- Possibilità di funzionamento tramite contatore esternoDimensioni- Tubo distributore: _________________________________ 50 mm - Altezza tubo distributore sopra la bombola: _______ +/- 5 mm- Conduttura allo scarico: ____________ 1/2” o 3/4” o 1” o 1 ¼ “- Conduttura alla salamoia: _____________________ 3/8” o 1/2”- Filettatura bombola: ____ 4” - 8 NPSM (opzione 2 ½” - 8 NPSM)- Altezza: __________________________________________ 269 mm- Larghezza: _______________________________________ 325 mm- Profondità: _______________________________________ 221 mm- Peso: ________________________________________________ 3.5 kgBombole utilizzabili- Addolcitore: ____________________________________ Ø 14”- 24”- Filtri:_____________________________________________ Ø 14” - 24” - Volume resina: ___________________________ da 100 lt a 325 ltPressione- Idrostatica: ________________________________________ 24 bar- Servizio: _________________________________________ 2 a 8 bar- Temperatura: ____________________________________1 a 45°C- Test pressione: __ 1-14 bar (250.00 cicli), 1-24 bar (70.000 cicli) Opzioni- Relè Esterno (VK0200)- Acqua Calda - Valvola filtro- SBV di sicurezza- Attacco Side Mount- Pistone NBP (No By-Pass) solo per valvole multiplexCertificati- Conformità Regolamento CE bassa tensione- CE - RoHS- ACS : 13 ACC LY 805
HYK-VALVESSCARICO
Drain
MISCELATOREMixing
ACCESSO EIETTOREAccess Injector
CAVO METERMeter Cable
LINEA SALAMOIABrine Line
VITI DI FISSAGGIO BASEBase Retaining Screws
INGRESSOInlet
USCITAOutlet
VK40- Valve material: ____________________________________ Noryl ®- Inlet / outlet:_____________________________________ 1“1/2 BSPFlow rate valve alone- Continuous (1,0 bar drop): _______________________ 11,6 m3/h - Peak (1,7 bar drop): _____________________________ 15,0 m3/h- Backwash (1,0 bar drop): ________________________ 11,6 m3/h- Max backwash (1,7 bar drop): ___________________ 15,0 m3/hMicroprocessor- Display: _________________ Large backlight display - 4, 5 digits- Parameter backup: ____________________ Back-up Capacitor - External relay : ___________________________ Optional (VK0200)- Power supply:* VK40-1: _______________________________ 230 V / 5V – 1A – DC * VK40-2 & * VK40-3: __________________ 230 V / 7,5V – 2 A – DC - Adjustable parameters: time of day, time of regeneration, cycles time, cyclical capacity, time forcing, reserve.- Reading: volume remaining, remaining time, cycle in pro-gress.- Regeneration: Hours, Timeclock, Meter delayed or immedi-ate, manual.- Regeneration Mode: Downflow / Upflow, Filter, Variable brin-ingGeneral Features:- DF & UF rigeneration without additional costs- Adjustable cicles- Brine fill with softened water (only UF)- Variable Brining- Piston movement with optical sensor and micro AUX- Easier maintenance ((injectors, flow regulators, etc)- Quick connexion to the drain line - Easy disassembly of the body from the adaptor- Integrated meter- Integrated mixing device- Duplex & Multiplex version by Wireless connexion of 2, 3, 4 or 5 control valves- Diagnostic programm up to the last 4 rigenerations- Possibility to working with external flow meterDimensions:- Distributor pilot: ____________________________________ 50 mm- Length above the tank: __________________________ +/- 5 mm- Drain line: ___________________________1/2” o 3/4” o 1” o 1 ¼ “- Brine line: ______________________________________ 3/8” o 1/2”- Mounting base: ________ 4’’- 8 NPSM (option 2 ½” - 8 NPSM)- Height: ___________________________________________ 269 mm- Width: ____________________________________________ 325 mm - Depth: ___________________________________________ 221 mm- Weight: ______________________________________________ 3.5 kgTanks Size application (recommended) - Water softener: __________________________________ Ø 14” - 24”- Filter: ____________________________________________Ø 14” - 24” - Resin volume: _______________________ from 100 lt up to 325 ltPressure- Hydrostatic:_______________________________________ 24 bar- Working:________________________________________ 2 to 8 bar- Temperature:____________________________________1 to 45°C- Pressure Test:_1-14 bar (250.00 cycles), 1-24 bar (70.000 cycles) Options- External Relay (VK0200) - Hot Water- Filter valve- SBV Safety brine Valve- Side Mount adapter- NBP Piston (No By-Pass) only for multiplex valvesCertificates- Compliant to CE low voltage regulations - CE - RoHS- ACS : 13 ACC LY 805
HYK-VALVES VK40 - 1”1/2
DIMENSIONI VK40-1/ VK40-1 DIMENSIONS 100
102,7 172
121
,6
228
70,
7
256
Dessus de bouteille
canule pour tube Ø 13 mm
326
51,50
103
148
filetage 1½'' BSPcylindrique
107
102
75,
6
filetage 4'' UN 2A
Raccord rapideØ 3/8'' (9,52 mm)
Tube distributeur: Ø 50 mmlongueur tube: minimum +3 mm au dessus de la bouteille maximum +8 mm au dessus de la bouteille
SCHEMI DI FLUSSO VK40-1/ VK40-1 FLOW DIAGRAMS
IN OUT
ValvolaBackpressure
A
S
Aspirazione/Suction
Servizio Down Flow / Down Flow Service
Eiettore / Injector
Scarico/DrainS
A Aspirazione/Suction
Ingreso/Inlet
Uscita/ Outlet
Salamoia/ Brine
Check Ball
OUT
ValvolaBackpressure
A
S
IN
Scarico/DrainS
A Aspirazione/Suction
Aspirazione/Suction
1 - Controlavaggio / Backwash
Eiettore / Injector
Ingreso/Inlet
Uscita/ Outlet
Salamoia/ Brine
Check Ball
S
A
IN OUT
ValvolaBackpressure
Scarico/DrainS
A Aspirazione/Suction
2 - Aspirazione salamoia / Brine SuctionIngreso/Inlet
Uscita/ Outlet
Salamoia/ Brine
Aspirazione/Suction
Eiettore / Injector
Check Ball
IN OUT
ValvolaBackpressure
A
SScarico/DrainS
A Aspirazione/Suction
3 - Risciacquo Rapido / Rapid RinseIngreso/Inlet
Uscita/ Outlet
Salamoia/ BrineEiettore / Injector
Aspirazione/Suction
Check Ball
IN
ValvolaBackpressure
A
S
OUT
Scarico/DrainS
A Aspirazione/Suction
4 - Riempimento / Brine RefillIngreso/Inlet
Uscita/ Outlet
Salamoia/ BrineEiettore / Injector
Aspirazione/Suction
Check BallCheck Ball
Check Ball
ESPLOSO PARTI DI RICAMBIO VK40-1/ VK40-1 SPARE PARTS DRAWING
14
13
1211
10
9
8
7
6
5
43
21
15
POS. COD. DESCRIZIONE/DESCRIPTION
1 VK2255 Actuator kit - main piston
2 VK2185 Piston plate kit 150 (1 set) - VK40
3 VK2160 Main piston 150 -VK40
4 VK2086 Main seals and spacers kit (1 set) - 150
5 VK2231 Valve body
6 VK2312 4" Threaded tank adaptor
7 VK2234-2 VAS Plate -150 - VK40-1
8 VK2235 Assembled brine valve body 3/8"
9 VK2195 Electronic and housing assembly (7,5 Volts 2A)
10 VK2245 Assembled brine valve elbow
11 VK2240 Brine valve cover
12 VK2313 Drain Retainer
13
- VK2296 0,8 m3/h DFR 13 mm outlet
- VK2297 1,1 m3/h DFR 13 mm outlet
- VK2298 1.6 m3/h DFR 13 mm outlet
- VK2299 0,8 m3/h DFR 19 mm outlet
- VK2300 1,1 m3/h DFR 19 mm outlet
- VK2301 1.6 m3/h DFR 19 mm outlet
- VK2302 0,8 m3/h DFR 3/4'' BSP outlet
- VK2303 1,1 m3/h DFR 3/4'' BSP outlet
- VK2304 1,6 m3/h DFR 3/4'' BSP outlet
- VK2305 2,3 m3/h DFR 1'' BSP outlet
- VK2306 3,3 m3/h DFR 1'' BSP outlet
- VK2307 5,2 m3/h DFR 1'' BSP outlet
- VK2308 7,0 m3/h DFR 1'' ¼ BSP outlet
14 VK2232 Cylinder head with plug on injector (all models)
15
- VK2314 1 ½" connector kit chrono valves
- VK2315 1 ½" connector kit with turbine meter
VK 40-1
Drain line Flow control available:
In-Outlet connectors 1½"
VK40 - 1”1/2 HYK-VALVES
HYK-VALVES VK40 - 1”1/2
DIMENSIONI VK40-2/ VK40-2 DIMENSIONS
102,7
228
70,
7
86,6
256
121
,6
172,2
Dessus de bouteille
suivant versions3/4'' BSP1'' BSP1¼'' BSP
51,50
103
269,7
filetage 1½'' BSPcylindrique
75,
6
78,4
223
filetage 4'' UN 2A
Raccord rapideØ 1/2'' (12,7 mm)
Tube distributeur: Ø 50 mmlongueur tube: minimum +3 mm au dessus de la bouteille maximum +8 mm au dessus de la bouteille
CHEMI DI FLUSSO VK 40-2/ VK40-2 FLOW DIAGRAMS
ValvolaBackpressure
Scarico/DrainS
A Aspirazione/Suction
IN OUT
S
A
Aspirazione/Suction
Servizio Down Flow / Down Flow Service
Eiettore / Injector
Ingreso/Inlet
Uscita/ Outlet
Salamoia/ Brine
Check Ball
ValvolaBackpressure
IN
A
Aspirazione/Suction
S
Scarico/DrainS
A Aspirazione/Suction
Controlavaggio / Backwash
Salamoia/ Brine
Ingreso/Inlet
Uscita/ Outlet
Eiettore / Injector
Check Ball
ValvolaBackpressure
AAspirazione
S
OUTIN
Scarico/DrainS
A Aspirazione/Suction
Aspirazione / Brine Suction
Salamoia/ Brine
Ingreso/Inlet
Uscita/ Outlet
Check Ball
ValvolaBackpressure
IN
S
A
Scarico/DrainS
A Aspirazione/Suction
Risciacquo Rapido / Rapid Rinse
Salamoia/ Brine
Ingreso/Inlet
Uscita/ OutletAspirazione/
Suction
Eiettore / Injector
Check Ball
A
Aspirazione/Suction
S
OUTIN
Scarico/DrainS
A Aspirazione/Suction
4 - Riempimento / Brine Refill
Salamoia/ Brine
Ingreso/Inlet
Uscita/ Outlet
ValvolaContropressione/
Backpressure Valve
Eiettore / Injector
Check Ball
ESPLOSO PARTI DI RICAMBIO VK40-2/ VK40-2 SPARE PARTS DRAWING
1
2
3
45
6
8
7
9
11
1213
14
10
15
HYK-VALVESVK40 - 1”1/2
POS. COD. DESCRIZIONE/DESCRIPTION
1 VK2255 Actuator kit - main piston
2 VK2185 Piston plate kit 150 (1 set) - VK40
3 VK2160 Main piston 150 -VK40
4 VK2086 Main seals and spacers kit (1 set) - 150
5 VK2231 Valve body
6 VK2312 4" Threaded tank adaptor
7 VK2234-1 Blind Plate - 150
8 VK2195 Electronic and housing assembly (7,5 Volts 2A)
9 VK2232 Cylinder head with plug on injector (all models)
10 VK2252 Motorized Brine valve 1/2"
11 VK2313 Drain Retainer
12
- VK2296 0,8 m3/h DFR 13 mm outlet
- VK2297 1,1 m3/h DFR 13 mm outlet
- VK2298 1.6 m3/h DFR 13 mm outlet
- VK2299 0,8 m3/h DFR 19 mm outlet
- VK2300 1,1 m3/h DFR 19 mm outlet
- VK2301 1.6 m3/h DFR 19 mm outlet
- VK2302 0,8 m3/h DFR 3/4'' BSP outlet
- VK2303 1,1 m3/h DFR 3/4'' BSP outlet
- VK2304 1,6 m3/h DFR 3/4'' BSP outlet
- VK2305 2,3 m3/h DFR 1'' BSP outlet
- VK2306 3,3 m3/h DFR 1'' BSP outlet
- VK2307 5,2 m3/h DFR 1'' BSP outlet
- VK2308 7,0 m3/h DFR 1'' ¼ BSP outlet
13
- VK2314 1 ½" connector kit chrono valves
- VK2315 1 ½" connector kit with turbine meter
VK 40-2
Drain line Flow control available:
In-Outlet connectors 1½"
DIMENSIONI VK40-3/ VK40-3 DIMENSIONS
102,7
228
70,
7
86,6
256
121
,6
172,2
Dessus de bouteille
suivant versions3/4'' BSP1'' BSP1¼'' BSP
355,6
51,50
103
177,7
filetage 1½'' BSPcylindrique
75,
6
78,4
223
filetage 4'' UN 2A
Raccord rapideØ 1/2'' (12,7 mm)
Tube distributeur: Ø 50 mmlongueur tube: minimum +3 mm au dessus de la bouteille maximum +8 mm au dessus de la bouteille
CHEMI DI FLUSSO VK 40-3 (MPX)/ VK40-2 (MPX) FLOW DIAGRAMS
ValvolaBackpressure
IN OUT
S
A
Aspirazione/Suction
Eiettore / Injector
Servizio Down Flow / Down Flow Service
Scarico/DrainS
A Aspirazione/Suction
Ingreso/Inlet
Alto colonna/ Top Tank
Salamoia/ Brine
Check Ball
ValvolaBackpressure
IN
S
A
Aspirazione/Suction
Eiettore / InjectorScarico/DrainS
A Aspirazione/Suction
Attesa / Stand By (MPX)Ingreso/Inlet
Alto colonna/ Top Tank
Salamoia/ Brine
OUT
Check Ball
Aspirazione / Brine Suction
OUT
S
IN
ValvolaBackpressure
A
Aspirazione/Suction
Eiettore / InjectorScarico/DrainS
A Aspirazione/Suction
Ingreso/Inlet
Alto colonna/ Top Tank
Salamoia/ Brine
Check Ball
OUT
S
ValvolaBackpressure
A
Aspirazione/Suction
Eiettore / InjectorScarico/DrainS
A Aspirazione/Suction
Ingreso/Inlet
Alto colonna/ Top Tank
Salamoia/ Brine
Risciacquo Rapido / Rapid Rinse
IN
Check Ball
4 - Riempimento / Brine Refill
OUT
S
ValvolaBackpressure
A
Aspirazione/Suction
Eiettore / InjectorScarico/DrainS
A Aspirazione/Suction
Ingreso/Inlet
Alto colonna/ Top Tank
Salamoia/ Brine
IN
Check Ball
S
IN OUT
ValvolaBackpressure
Aspirazione/Suction
A
Eiettore / Injector
Controlavaggio / Backwash
Scarico/DrainS
A Aspirazione/Suction
Ingreso/Inlet
Alto colonna/ Top Tank
Salamoia/ Brine
Check Ball
HYK-VALVES VK40 - 1”1/2
ESPLOSO PARTI DI RICAMBIO VK40-3/ VK40-3 SPARE PARTS DRAWING
1
2
3
45
6
8
79
11
12
1314
10
15
16
POS. COD. DESCRIZIONE/DESCRIPTION
1 VK2255 Actuator kit - main piston
2 VK2185 Piston plate CO150 (NBP)
3 VK2160 Main piston 150 -VK40
4 VK2086 Main seals and spacers kit (1 set) - 150
5 VK2231 Valve body
6 VK2312 4" Threaded tank adaptor
7 VK2161 NBP Piston - 150
8 VK2195 Electronic and housing assembly (7,5 Volts 2A)
9 VK2185 Piston plate CO150 (NBP)
10 VK2265 Actuator kit - CO piston (closing outlet)
11 VK2232 Cylinder head with plug on injector (all models)
12 Ka-40-D0-3081 Motorized Brine valve 1/2"
13 VK2313 Drain Retainer
14
- VK2296 0,8 m3/h DFR 13 mm outlet
- VK2297 1,1 m3/h DFR 13 mm outlet
- VK2298 1.6 m3/h DFR 13 mm outlet
- VK2299 0,8 m3/h DFR 19 mm outlet
- VK2300 1,1 m3/h DFR 19 mm outlet
- VK2301 1.6 m3/h DFR 19 mm outlet
- VK2302 0,8 m3/h DFR 3/4'' BSP outlet
- VK2303 1,1 m3/h DFR 3/4'' BSP outlet
- VK2304 1,6 m3/h DFR 3/4'' BSP outlet
- VK2305 2,3 m3/h DFR 1'' BSP outlet
- VK2306 3,3 m3/h DFR 1'' BSP outlet
- VK2307 5,2 m3/h DFR 1'' BSP outlet
- VK2308 7,0 m3/h DFR 1'' ¼ BSP outlet
15
- VK2314 1 ½" connector kit chrono valves
- VK2315 1 ½" connector kit with turbine meter
VK 40-3
Drain line Flow control available:
In-Outlet connectors 1½"
HYK-VALVESVK40 - 1”1/2
HYK-VALVES
TABELLE EIETTORI / INJECTOS TABLES
VK40 - 1”1/2
Down-flow standard settings for 120 g of salt per litre of resin
Valve Tank In
ject
or
Salt
Cycle
1
Cycle
2
Cycle
3
Cycle
4
Wat
er u
se
Back
was
h
Brin
ing
(dra
w)
Slow
rins
e
Rapi
d rin
se
Tank
refil
l
VK32
-1
VK32
-2
VK40
-1
VK40
-2
VK50
-2
Dim
ensio
ns
Volu
me
(L)
Open
ing
Resin
(L)
Inje
ctor
n°
Salt
volu
me
(kg)
Brin
e vo
lum
e
Tim
e
Flow
Tim
e
Flow
Tim
e dr
aw +
slow
rins
e
Tim
e
Volu
me
Tim
e
Flow
DFR
m³/
h
12 X 48 79 2½'' 55 1 6,6 20,6 5 1,9 10,9 1,8 33 5 18,3 4,6 0,8 210 14 X 52 115 2½'' 75 2 9 28,1 5 2,4 11,7 3,3 35 5 25,0 6,3 1,1 324 14 X 65 148 2½'' or 4'' 100 2 12 37,5 5 2,4 15,6 3,3 47 5 33,3 8 1,1 371
16 X 65 194 2½'' or 4'' 125 3 15 46,9 5 4,0 11,7 4,5 35 5 41,7 10 1,6 466
16 X 65 194 2½'' or 4'' 125 3 15 46,9 5 4,0 11,7 4,5 35 5 41,7 4 1,6 466 18 X 65 257 4'' 170 3 20 63,8 8 4,0 15,9 4,5 48 6 56,7 6 1,6 645 21 X 62 330 4'' 220 4 35 110,0 5 5 97,8 10 2,3
24 X 72 473 4'' 310 5 50 155,0 5 5 137,8 14 3,3
30 X 72 697 4'' 460 6 74 230,0 5 5 204,4 20 5,2
36 X 72 1011 4'' 700 7 112 350,0 5 5 311,1 31 7,0
Note: These values are only setting indications applicable to softeners with VK valves. They are determined for standard resin use and for an
average temperature of 15°C. They must be adapted in accordance with the specific location of every installation. In any case they do not involve Hytek’s responsibility.
Injector
Drain flow regulator (DFR) Range
Cappers | Tel : +33 (0) 473 94 84 87 | www.cappers.fr
Down- litre of resin
Valve Tank
Inje
ctor
Salt
Cycle
1
Cycle
2
Cycle
3
Cycle
4
Wat
er u
se
Back
was
h
Brin
ing
(dra
w)
Slow
rins
e
Rapi
d rin
se
Tank
refil
l
VK32
-1
VK32
-2
VK40
-1
VK40
-2
VK50
-2
Dim
ensio
ns
Volu
me
(L)
Open
ing
Resin
(L)
Inje
ctor
n°
Salt
volu
me
(kg)
Brin
e vo
lum
e
Tim
e
Flow
Tim
e
Flow
Tim
e dr
aw +
slow
rins
e
Tim
e
Volu
me
Tim
e
Flow
DFR
m³/
h
12 X 48 79 2½'' 55 1 8,8 27,5 5 1,9 14,5 1,8 43 5 24,4 6,1 0,8 236 14 X 52 115 2½'' 75 2 12 37,5 5 2,4 15,6 3,3 47 5 33,3 8,3 1,1 371 14 X 65 148 2½'' or 4'' 100 2 16 50,0 5 2,4 20,8 3,3 63 5 44,4 11 1,1 434
16 X 65 194 2½'' or 4'' 125 3 20 62,5 5 4,0 15,6 4,5 47 5 55,6 14 1,6 533
16 X 65 194 2½'' or 4'' 125 3 20 62,5 5 4,0 15,6 4,5 47 5 55,6 6 1,6 533 18 X 65 257 4'' 170 3 27 85,0 8 4,0 21,3 4,5 64 6 75,6 8 1,6 736 21 X 62 330 4'' 220 4 35 110,0 5 5 97,8 10 2,3
24 X 72 473 4'' 310 5 50 155,0 5 5 137,8 14 3,3
30 X 72 697 4'' 460 6 74 230,0 5 5 204,4 20 5,2
36 X 72 1011 4'' 700 7 112 350,0 5 5 311,1 31 7,0
Note: These values are only setting indications applicable to softeners with Cappers valves. They are determined for standard resin use and for an average temperature of 15°C. They must be adapted in accordance with the specific location of every installation. In any case they do not involve Cappers’ responsibility.
Drain flow regulator (DFR) Range
Injector
Down-flow standard settings for 120 g of salt per litre of resin
Valve Tank
Inje
ctor
Salt
Cycle
1
Cycle
2
Cycle
3
Cycle
4
Wat
er u
se
Back
was
h
Brin
ing
(dra
w)
Slow
rins
e
Rapi
d rin
se
Tank
refil
l
VK32
-1
VK32
-2
VK40
-1
VK40
-2
VK50
-2
Dim
ensio
ns
Volu
me
(L)
Open
ing
Resin
(L)
Inje
ctor
n°
Salt
volu
me
(kg)
Brin
e vo
lum
e
Tim
e
Flow
Tim
e
Flow
Tim
e dr
aw +
slow
rins
e
Tim
e
Volu
me
Tim
e
Flow
DFR
m³/
h
12 X 48 79 2½'' 55 1 6,6 20,6 5 1,9 10,9 1,8 33 5 18,3 4,6 0,8 210 14 X 52 115 2½'' 75 2 9 28,1 5 2,4 11,7 3,3 35 5 25,0 6,3 1,1 324 14 X 65 148 2½'' or 4'' 100 2 12 37,5 5 2,4 15,6 3,3 47 5 33,3 8 1,1 371
16 X 65 194 2½'' or 4'' 125 3 15 46,9 5 4,0 11,7 4,5 35 5 41,7 10 1,6 466
16 X 65 194 2½'' or 4'' 125 3 15 46,9 5 4,0 11,7 4,5 35 5 41,7 4 1,6 466 18 X 65 257 4'' 170 3 20 63,8 8 4,0 15,9 4,5 48 6 56,7 6 1,6 645 21 X 62 330 4'' 220 4 35 110,0 5 5 97,8 10 2,3
24 X 72 473 4'' 310 5 50 155,0 5 5 137,8 14 3,3
30 X 72 697 4'' 460 6 74 230,0 5 5 204,4 20 5,2
36 X 72 1011 4'' 700 7 112 350,0 5 5 311,1 31 7,0
Note: These values are only setting indications applicable to softeners with VK valves. They are determined for standard resin use and for an
average temperature of 15°C. They must be adapted in accordance with the specific location of every installation. In any case they do not involve Hytek’s responsibility.
Injector
Drain flow regulator (DFR) Range
Nota: i valori sopra indicati sono riferiti esclusivamente ad addolcitori con valvole VK e sono riferiti a test eseguiti su resina standard ad una temperatura media di 15 ° C. I dati possono variare in riferimento alle caratteristiche specifiche dell’ impianto dove ven-gono montate le valvole VK. In ogni caso la tabella sopra è indicativa ed esonera Hytek da ogni responsabilità.Note: These values are only setting indications applicable to softeners with VK valves. They are determined for standard resin use and for an average temperature of 15°C. They must be adapted in accordance with the specific location of every installation. In any case they do not involve Hytek’s responsability.
Impostazioni Down-Flow basate su 120 g di sale per litro di resina Down-Flow standard settings for 120 g of salt per litre of resin.
Iniettore/Injector
Impostazioni Down-Flow basate su 160 g di sale per litro di resina Down-Flow standard settings for 160 g of salt per litre of resin.
Nota: i valori sopra indicati sono riferiti esclusivamente ad addolcitori con valvole VK e sono riferiti a test eseguiti su resina standard ad una temperatura media di 15 ° C. I dati possono variare in riferimento alle caratteristiche specifiche dell’ impianto dove ven-gono montate le valvole VK. In ogni caso la tabella sopra è indicativa ed esonera Hytek da ogni responsabilità.Note: These values are only setting indications applicable to softeners with VK valves. They are determined for standard resin use and for an average temperature of 15°C. They must be adapted in accordance with the specific location of every installation. In any case they do not involve Hytek’s responsability.
Tipi di regolatori di scarico (DFR)/Drain flow regulator (DFR)
Down-flow standard settings for 120 g of salt per litre of resin
Valve Tank
Inje
ctor
Salt
Cycle
1
Cycle
2
Cycle
3
Cycle
4
Wat
er u
se
Back
was
h
Brin
ing
(dra
w)
Slow
rins
e
Rapi
d rin
se
Tank
refil
l
VK32
-1
VK32
-2
VK40
-1
VK40
-2
VK50
-2
Dim
ensio
ns
Volu
me
(L)
Open
ing
Resin
(L)
Inje
ctor
n°
Salt
volu
me
(kg)
Brin
e vo
lum
e
Tim
e
Flow
Tim
e
Flow
Tim
e dr
aw +
slow
rins
e
Tim
e
Volu
me
Tim
e
Flow
DFR
m³/
h
12 X 48 79 2½'' 55 1 6,6 20,6 5 1,9 10,9 1,8 33 5 18,3 4,6 0,8 210 14 X 52 115 2½'' 75 2 9 28,1 5 2,4 11,7 3,3 35 5 25,0 6,3 1,1 324 14 X 65 148 2½'' or 4'' 100 2 12 37,5 5 2,4 15,6 3,3 47 5 33,3 8 1,1 371
16 X 65 194 2½'' or 4'' 125 3 15 46,9 5 4,0 11,7 4,5 35 5 41,7 10 1,6 466
16 X 65 194 2½'' or 4'' 125 3 15 46,9 5 4,0 11,7 4,5 35 5 41,7 4 1,6 466 18 X 65 257 4'' 170 3 20 63,8 8 4,0 15,9 4,5 48 6 56,7 6 1,6 645 21 X 62 330 4'' 220 4 35 110,0 5 5 97,8 10 2,3
24 X 72 473 4'' 310 5 50 155,0 5 5 137,8 14 3,3
30 X 72 697 4'' 460 6 74 230,0 5 5 204,4 20 5,2
36 X 72 1011 4'' 700 7 112 350,0 5 5 311,1 31 7,0
Note: These values are only setting indications applicable to softeners with VK valves. They are determined for standard resin use and for an
average temperature of 15°C. They must be adapted in accordance with the specific location of every installation. In any case they do not involve Hytek’s responsibility.
Injector
Drain flow regulator (DFR) Range
Tipi di regolatori di scarico (DFR)/Drain flow regulator (DFR)
HYK-VALVES
DIAGRAMMI DI FLUSSO / FLOW DIAGRAMS
VK40 - 1”1/2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
bars
bars
bars
bars
bars
bars
bars
bars
l/mn
l/mn
l/mn
l/mn
l/mn
l/mn
l/mn
l/mn
l/mn
l/mn
2,0
2,0
2,0
2,0
3,0
3,0
3,0
3,0
4,0
4,0
4,0
4,0
5,0
5,0
5,0
5,0
6,0
6,0
6,0
6,0
7,0
7,0
7,0
7,0
8,0
8,0
8,0
8,0
2,0
2,0
2,0
2,0
3,0
3,0
3,0
3,0
4,0
4,0
4,0
4,0
5,0
5,0
5,0
5,0
6,0
6,0
6,0
6,0
7,0
7,0
7,0
7,0
8,0
8,0
8,0
8,0
8,0
8,0
8,0
8,0
9,0
9,0
9,0
9,0
Brine draw Slow rinse
Injector n°1
Injector n°2
Injector n°3
Injector n°4
SCA industrial - Flow diagrams
Slow rinseBrine draw
Slow rinse
Slow rinse
Brine draw
Brine draw
2
2
2
2
2
2
3
3
3
3
3
3
4
4
4
4
4
4
5
5
5
5
5
5
6
6
6
6
6
6
7
7
7
7
7
7
8
8
8
8
8
8
bars
bars
bars
bars
bars
bars
l/mn
l/mn
l/mnl/mn
l/mn
l/mn
l/mn
8,0
8,0
8,0
10,0
10,0
10,0
12,0
12,0
12,0
14,0
14,0
14,0
16,0
16,0
16,0
18,0
18,0
18,0
20,0
20,0
20,0
6,0
6,0
6,0
8,0
8,0
8,0
10,0
10,0
10,0
12,0
12,0
12,0
14,0
14,0
14,0
16,0
16,0
16,0
18,0
18,0
18,0
20,0
20,0
20,0
Brine draw Slow rinse
Injector n°5
Injector n°6
Injector n°7
SCA industrial - Flow diagrams
Slow rinseBrine draw
Slow rinseBrine draw
4,0
4,0
4,0
VK50 - 2”
VK50- Materiale del corpo valvola: _______________________ Noryl ® - Entrata / Uscita: ____________________________________ 2” BSPPortata Valvola sola- In continuo (Dp = 1,0 bar): _____________________ 21,7 m3/h - Valore massimo (Dp = 1,7 bar): __________________ 28,2 m3/h- Contolav. (Dp = 1,0 bar): ________________________ 21,7 m3/h- Contolav. max (Dp = 1,7 bar): ___________________ 28,2 m3/hMicroprocessore- Visualizzazione: ____ display digitale retro illuminato, 4, 5 cifre- Salvaguardia parametri: ___ Back-up tramite condensatore- Relè Esterno: ___________________________ Opzionale (VK0200)- Alimentazione elettrica:* VK50-1: _______________________________ 230 V / 5V – 1A – DC * VK50-2 & * VK50-3: __________________ 230 V / 7,5V – 2 A – DC - Parametri impostabili: Ora del giorno, ora di rigenerazione, tempi dei cicli, capacità ciclica, forzatura a tempo, riserva. - Lettura: Volume restante, defalco del tempo, posizione del ciclo in corso.- Rigenerazione: a giorni fissi, a giorni selezionabili, volumetrica ritardata o immediata, manuale- Modalità Rigenerazione: Up Flow, Down Flow, Filtro, Salamoia variabileCaratteristiche:- Rigenerazione DF & UF senza costi aggiuntivi- Regolazione dei Cicli- Riempimento vasca sale con acqua addolcita (solo UF)- Salamoia variabile- Movimentazione pistone con sensore ottico e micro AUX- Manutenzione semplificata (iniettori, regolatori scarico etc)- Rapida connessione alla linea di scarico- Facile disassemblaggio del corpo dall’ adattatore - Contatore integrato- Miscelatore della durezza integrato - Versione Duplex & Multiplex tramite intefaccia WiFi con ges-tione di 2,3,4 o 5 valvole- Programma statistico fino alle ultime 4 rigenerazioni- Possibilità di funzionamento tramite contatore esternoDimensioni- Tubo distributore: _________________________________ 50 mm - Altezza tubo distributore sopra la bombola: _______ +/- 5 mm- Conduttura allo scarico: _____________ 1/2” o 3/4” o 1” o 1 ¼ “- Conduttura alla salamoia: _____________________ 3/ 8” o 1/2”- Filettatura bombola: ___________________________ 4” - 8 NPSM- Altezza: __________________________________________ 269 mm- Larghezza: _______________________________________ 325 mm- Profondità: _______________________________________ 221 mm- Peso: ________________________________________________ 4 kgBombole utilizzabili- Addolcitore: ____________________________________ Ø 24”- 36”- Filtri:_____________________________________________Ø 21” - 36” - Volume resina: ___________________________ da 200 lt a 700 ltPressione- Idrostatica: ________________________________________ 24 bar- Servizio: _________________________________________ 2 a 8 bar- Temperatura: ____________________________________1 a 45°C- Test pressione: __ 1-14 bar (250.00 cicli), 1-24 bar (70.000 cicli) Opzioni- Relè Esterno (VK0200)- Acqua Calda - Valvola filtro- SBV di sicurezza- Attacco Side Mount- Pistone NBP (No By-Pass) solo per valvole multiplexCertificati- Conformità Regolamento CE bassa tensione- CE - RoHS- ACS : 13 ACC LY 805
VK50- Valve material: ____________________________________ Noryl ®- Inlet / outlet:________________________________________ 2” BSPFlow rate valve alone- Continuous (1,0 bar drop): _______________________ 21,7 m3/h - Peak (1,7 bar drop): _____________________________ 28,2 m3/h- Backwash (1,0 bar drop): ________________________ 21,7 m3/h- Max backwash (1,7 bar drop): ___________________ 28,2 m3/hMicroprocessor- Display: _________________ Large backlight display - 4, 5 digits- Parameter backup: ____________________ Back-up Capacitor - External relay : ___________________________ Optional (VK0200)- Power supply:* VK50-1: _______________________________ 230 V / 5V – 1A – DC * VK50-2 & * VK50-3: __________________ 230 V / 7,5V – 2 A – DC - Adjustable parameters: time of day, time of regeneration, cycles time, cyclical capacity, time forcing, reserve.- Reading: volume remaining, remaining time, cycle in pro-gress.- Regeneration: Hours, Timeclock, Meter delayed or immedi-ate, manual.- Regeneration Mode: Downflow / Upflow, Filter, Variable Brin-ingGeneral Features:- DF & UF rigeneration without additional costs- Adjustable cicles- Brine fill with softened water (only UF)- Variable Brining- Piston movement with optical sensor and micro AUX- Easier maintenance ((injectors, flow regulators, etc)- Quick connexion to the drain line - Easy disassembly of the body from the adaptor- Integrated meter- Integrated mixing device- Duplex & Multiplex version by Wireless connexion of 2, 3, 4 or 5 control valves- Diagnostic programm up to the last 4 rigenerations- Possibility to working with external flow meterDimensions:- Distributor pilot: ____________________________________ 50 mm- Length above the tank: __________________________ +/- 5 mm- Drain line: ___________________________1/2” o 3/4” o 1” o 1 ¼ “- Brine line: ______________________________________ 3/8” o 1/2”- Mounting base: ________________________________ 4’’- 8 NPSM- Height: ___________________________________________ 269 mm- Width: ____________________________________________ 325 mm - Depth: ___________________________________________ 221 mm- Weight: ______________________________________________ 4 kgTanks Size application (recommended) - Water softener: __________________________________ Ø 24” - 36”- Filter: ____________________________________________Ø 21” - 36” - Resin volume: _______________________ from 200 lt up to 700 ltPressure- Hydrostatic:_______________________________________ 24 bar- Working:________________________________________ 2 to 8 bar- Temperature:____________________________________1 to 45°C- Pressure Test:_1-14 bar (250.00 cycles), 1-24 bar (70.000 cycles) Options- External Relay (VK0200)- Hot Water- Filter valve- SBV Safety brine Valve- Side Mount adapter- NBP Piston (No By-Pass) only for multiplex valvesCertificates- Compliant to CE low voltage regulations - CE - RoHS- ACS : 13 ACC LY 805
HYK-VALVESSCARICO
Drain
MISCELATOREMixing
ACCESSO EIETTOREAccess Injector
CAVO METERMeter Cable
LINEA SALAMOIABrine Line
VITI DI FISSAGGIO BASEBase Retaining Screws
INGRESSOInlet
USCITAOutlet
VK50 - 2” HYK-VALVES
DIMENSIONI VK50-1/ VK50-1 DIMENSIONS 100
102,7
228
70,
7
256
171,2
116
,5
Dessus de bouteille
canule pour tube Ø 13 mm
326
51,50
103
148
filetage 2'' BSPcylindrique
107
102
75,
6
filetage 4'' UN 2A
Raccord rapideØ 3/8'' (9,52 mm)
Tube distributeur: Ø 50 mmlongueur tube: minimum +3 mm au dessus de la bouteille maximum +8 mm au dessus de la bouteille
SCHEMI DI FLUSSO VK50-1/ VK50-1 FLOW DIAGRAMS
IN OUT
ValvolaBackpressure
A
S
Aspirazione/Suction
Servizio Down Flow / Down Flow Service
Eiettore / Injector
Scarico/DrainS
A Aspirazione/Suction
Ingreso/Inlet
Uscita/ Outlet
Salamoia/ Brine
Check Ball
OUT
ValvolaBackpressure
A
S
IN
Scarico/DrainS
A Aspirazione/Suction
Aspirazione/Suction
1 - Controlavaggio / Backwash
Eiettore / Injector
Ingreso/Inlet
Uscita/ Outlet
Salamoia/ Brine
Check Ball
S
A
IN OUT
ValvolaBackpressure
Scarico/DrainS
A Aspirazione/Suction
2 - Aspirazione salamoia / Brine SuctionIngreso/Inlet
Uscita/ Outlet
Salamoia/ Brine
Aspirazione/Suction
Eiettore / Injector
Check Ball
IN OUT
ValvolaBackpressure
A
SScarico/DrainS
A Aspirazione/Suction
3 - Risciacquo Rapido / Rapid RinseIngreso/Inlet
Uscita/ Outlet
Salamoia/ BrineEiettore / Injector
Aspirazione/Suction
Check Ball
IN
ValvolaBackpressure
A
S
OUT
Scarico/DrainS
A Aspirazione/Suction
4 - Riempimento / Brine RefillIngreso/Inlet
Uscita/ Outlet
Salamoia/ BrineEiettore / Injector
Aspirazione/Suction
Check BallCheck Ball
Check Ball
VK50 - 2”HYK-VALVES
ESPLOSO PARTI DI RICAMBIO VK50-1/ VK50-1 SPARE PARTS DRAWING
14
13
1211
10
9
8
7
6
5
43
21
15
POS. COD. DESCRIZIONE/DESCRIPTION
1 VK2255 Actuator kit - main piston
2 VK2190 Piston plate kit 200 (1 set) - VK50
3 VK2165 Main piston 200 - VK50
4 VK2087 Main seals and spacers kit (1 set) - 200
5 VK2231 Valve body
6 VK2312 4" Threaded tank adaptor
7 VK2234-4 VAS Plate - 200 - VK50-1
8 VK2235 Assembled brine valve body 3/8"
9 VK2195 Electronic and housing assembly (7,5 Volts 2A)
10 VK2245 Assembled brine valve elbow
11 VK2240 Brine valve cover
12 VK2313 Drain Retainer
13
- VK2296 0,8 m3/h DFR 13 mm outlet
- VK2297 1,1 m3/h DFR 13 mm outlet
- VK2298 1.6 m3/h DFR 13 mm outlet
- VK2299 0,8 m3/h DFR 19 mm outlet
- VK2300 1,1 m3/h DFR 19 mm outlet
- VK2301 1.6 m3/h DFR 19 mm outlet
- VK2302 0,8 m3/h DFR 3/4'' BSP outlet
- VK2303 1,1 m3/h DFR 3/4'' BSP outlet
- VK2304 1,6 m3/h DFR 3/4'' BSP outlet
- VK2305 2,3 m3/h DFR 1'' BSP outlet
- VK2306 3,3 m3/h DFR 1'' BSP outlet
- VK2307 5,2 m3/h DFR 1'' BSP outlet
- VK2308 7,0 m3/h DFR 1'' ¼ BSP outlet
14 VK2232 Cylinder head with plug on injector (all models)
15
- VK2316 2" connector kit chrono valves
- VK2317 2" connector kit with turbine meter
VK 50-1
Drain line Flow control available:
In-Outlet connectors 2''
VK50 - 2” HYK-VALVES
DIMENSIONI VK50-2/ VK50-2 DIMENSIONS
102,7
228
70,
7
171,2
116
,5
86,6
256
Dessus de bouteille
suivant versions3/4'' BSP1'' BSP1¼'' BSP
51,50
103
269,7
filetage 2'' BSPcylindrique
75,
6
78,4
223
filetage 4'' UN 2A
Raccord rapideØ 1/2'' (12,7 mm)
Tube distributeur: Ø 50 mmlongueur tube: minimum +3 mm au dessus de la bouteille maximum +8 mm au dessus de la bouteille
CHEMI DI FLUSSO VK 50-2/ VK50-2 FLOW DIAGRAMS
ValvolaBackpressure
Scarico/DrainS
A Aspirazione/Suction
IN OUT
S
A
Aspirazione/Suction
Servizio Down Flow / Down Flow Service
Eiettore / Injector
Ingreso/Inlet
Uscita/ Outlet
Salamoia/ Brine
Check Ball
ValvolaBackpressure
IN
A
Aspirazione/Suction
S
Scarico/DrainS
A Aspirazione/Suction
Controlavaggio / Backwash
Salamoia/ Brine
Ingreso/Inlet
Uscita/ Outlet
Eiettore / Injector
Check Ball
ValvolaBackpressure
AAspirazione
S
OUTIN
Scarico/DrainS
A Aspirazione/Suction
Aspirazione / Brine Suction
Salamoia/ Brine
Ingreso/Inlet
Uscita/ Outlet
Check Ball
ValvolaBackpressure
IN
S
A
Scarico/DrainS
A Aspirazione/Suction
Risciacquo Rapido / Rapid Rinse
Salamoia/ Brine
Ingreso/Inlet
Uscita/ OutletAspirazione/
Suction
Eiettore / Injector
Check Ball
A
Aspirazione/Suction
S
OUTIN
Scarico/DrainS
A Aspirazione/Suction
4 - Riempimento / Brine Refill
Salamoia/ Brine
Ingreso/Inlet
Uscita/ Outlet
ValvolaContropressione/
Backpressure Valve
Eiettore / Injector
Check Ball
ESPLOSO PARTI DI RICAMBIO VK50-2/ VK50-2 SPARE PARTS DRAWING
1
2
3
45
6
8
7
9
11
1213
14
10
15
POS. COD. DESCRIZIONE/DESCRIPTION
1 VK2255 Actuator kit - main piston
2 VK2190 Piston plate kit 200 (1 set) - VK50
3 VK2165 Main piston 200 - VK50
4 VK2087 Main seals and spacers kit (1 set) - 200
5 VK2231 Valve body
6 VK2312 4" Threaded tank adaptor
7 VK2234-3 Blind Plate - 200
8 VK2195 Electronic and housing assembly (7,5 Volts 2A)
9 VK2232 Cylinder head with plug on injector (all models)
10 VK2252 Motorized Brine valve 1/2"
11 VK2313 Drain Retainer
12
- VK2296 0,8 m3/h DFR 13 mm outlet
- VK2297 1,1 m3/h DFR 13 mm outlet
- VK2298 1.6 m3/h DFR 13 mm outlet
- VK2299 0,8 m3/h DFR 19 mm outlet
- VK2300 1,1 m3/h DFR 19 mm outlet
- VK2301 1.6 m3/h DFR 19 mm outlet
- VK2302 0,8 m3/h DFR 3/4'' BSP outlet
- VK2303 1,1 m3/h DFR 3/4'' BSP outlet
- VK2304 1,6 m3/h DFR 3/4'' BSP outlet
- VK2305 2,3 m3/h DFR 1'' BSP outlet
- VK2306 3,3 m3/h DFR 1'' BSP outlet
- VK2307 5,2 m3/h DFR 1'' BSP outlet
- VK2308 7,0 m3/h DFR 1'' ¼ BSP outlet
13
- VK2316 2" connector kit chrono valves
- VK2317 2" connector kit with turbine meter
VK 50-2
Drain line Flow control available:
In-Outlet connectors 2''
VK50 - 2”HYK-VALVES
DIMENSIONI VK50-3/ VK50-3 DIMENSIONS
102,7
228
70,
7
86,6
256
116
,5
171,2
Dessus de bouteille
suivant versions3/4'' BSP1'' BSP1¼'' BSP
355,6
51,50
103
177,7
filetage 2'' BSPcylindrique
75,
6
78,4
223
filetage 4'' UN 2A
Raccord rapideØ 1/2'' (12,7 mm)
Tube distributeur: Ø 50 mmlongueur tube: minimum +3 mm au dessus de la bouteille maximum +8 mm au dessus de la bouteille
CHEMI DI FLUSSO VK 50-3 (MPX)/ VK50-2 (MPX) FLOW DIAGRAMS
ValvolaBackpressure
IN OUT
S
A
Aspirazione/Suction
Eiettore / Injector
Servizio Down Flow / Down Flow Service
Scarico/DrainS
A Aspirazione/Suction
Ingreso/Inlet
Alto colonna/ Top Tank
Salamoia/ Brine
Check Ball
ValvolaBackpressure
IN
S
A
Aspirazione/Suction
Eiettore / InjectorScarico/DrainS
A Aspirazione/Suction
Attesa / Stand By (MPX)Ingreso/Inlet
Alto colonna/ Top Tank
Salamoia/ Brine
OUT
Check Ball
Aspirazione / Brine Suction
OUT
S
IN
ValvolaBackpressure
A
Aspirazione/Suction
Eiettore / InjectorScarico/DrainS
A Aspirazione/Suction
Ingreso/Inlet
Alto colonna/ Top Tank
Salamoia/ Brine
Check Ball
OUT
S
ValvolaBackpressure
A
Aspirazione/Suction
Eiettore / InjectorScarico/DrainS
A Aspirazione/Suction
Ingreso/Inlet
Alto colonna/ Top Tank
Salamoia/ Brine
Risciacquo Rapido / Rapid Rinse
IN
Check Ball
4 - Riempimento / Brine Refill
OUT
S
ValvolaBackpressure
A
Aspirazione/Suction
Eiettore / InjectorScarico/DrainS
A Aspirazione/Suction
Ingreso/Inlet
Alto colonna/ Top Tank
Salamoia/ Brine
IN
Check Ball
S
IN OUT
ValvolaBackpressure
Aspirazione/Suction
A
Eiettore / Injector
Controlavaggio / Backwash
Scarico/DrainS
A Aspirazione/Suction
Ingreso/Inlet
Alto colonna/ Top Tank
Salamoia/ Brine
Check Ball
VK50 - 2” HYK-VALVES
ESPLOSO PARTI DI RICAMBIO VK50-3/ VK50-3 SPARE PARTS DRAWING
1
2
3
45
6
8
79
11
12
1314
10
15
16
POS. COD. DESCRIZIONE/DESCRIPTION
1 VK2255 Actuator kit - main piston
2 VK2193 Piston plate CO200 (NBP)
3 VK2165 Main piston 200 - VK50
4 VK2087 Main seals and spacers kit (1 set) - 200
5 VK2231 Valve body
6 VK2312 4" Threaded tank adaptor
7 VK2166 NBP Piston - 200
8 VK2195 Electronic and housing assembly (7,5 Volts 2A)
9 VK2193 Piston plate CO200 (NBP)
10 VK2265 Actuator kit - CO piston (closing outlet)
11 VK2232 Cylinder head with plug on injector (all models)
12 Ka-40-D0-3081 Motorized Brine valve 1/2"
13 VK2313 Drain Retainer
14
- VK2296 0,8 m3/h DFR 13 mm outlet
- VK2297 1,1 m3/h DFR 13 mm outlet
- VK2298 1.6 m3/h DFR 13 mm outlet
- VK2299 0,8 m3/h DFR 19 mm outlet
- VK2300 1,1 m3/h DFR 19 mm outlet
- VK2301 1.6 m3/h DFR 19 mm outlet
- VK2302 0,8 m3/h DFR 3/4'' BSP outlet
- VK2303 1,1 m3/h DFR 3/4'' BSP outlet
- VK2304 1,6 m3/h DFR 3/4'' BSP outlet
- VK2305 2,3 m3/h DFR 1'' BSP outlet
- VK2306 3,3 m3/h DFR 1'' BSP outlet
- VK2307 5,2 m3/h DFR 1'' BSP outlet
- VK2308 7,0 m3/h DFR 1'' ¼ BSP outlet
15
- VK2316 2" connector kit chrono valves
- VK2317 2" connector kit with turbine meter
VK 50-3
Drain line Flow control available:
In-Outlet connectors 2''
VK50 - 2”HYK-VALVES
VK50 - 2” HYK-VALVES
TABELLE EIETTORI / INJECTOS TABLES
Down-flow standard settings for 120 g of salt per litre of resin
Valve Tank
Inje
ctor
Salt
Cycle
1
Cycle
2
Cycle
3
Cycle
4
Wat
er u
se
Ba
ckw
ash
Brin
ing
(dra
w)
Slow
rins
e
Rapi
d rin
se
Tank
refil
l
VK32
-1
VK32
-2
VK40
-1
VK40
-2
VK50
-2
Dim
ensio
ns
Volu
me
(L)
Open
ing
Resin
(L)
Inje
ctor
n°
Salt
volu
me
(kg)
Brin
e vo
lum
e
Tim
e
Flow
Tim
e
Flow
Tim
e dr
aw +
slow
rins
e
Tim
e
Volu
me
Tim
e
Flow
DFR
m³/
h
12 X 48 79 2½'' 55 1 6,6 20,6 5 1,9 10,9 1,8 33 5 18,3 4,6 0,8 210 14 X 52 115 2½'' 75 2 9 28,1 5 2,4 11,7 3,3 35 5 25,0 6,3 1,1 324 14 X 65 148 2½'' or 4'' 100 2 12 37,5 5 2,4 15,6 3,3 47 5 33,3 8 1,1 371
16 X 65 194 2½'' or 4'' 125 3 15 46,9 5 4,0 11,7 4,5 35 5 41,7 10 1,6 466
16 X 65 194 2½'' or 4'' 125 3 15 46,9 5 4,0 11,7 4,5 35 5 41,7 4 1,6 466 18 X 65 257 4'' 170 3 20 63,8 8 4,0 15,9 4,5 48 6 56,7 6 1,6 645 21 X 62 330 4'' 220 4 35 110,0 5 5 97,8 10 2,3
24 X 72 473 4'' 310 5 50 155,0 5 5 137,8 14 3,3
30 X 72 697 4'' 460 6 74 230,0 5 5 204,4 20 5,2
36 X 72 1011 4'' 700 7 112 350,0 5 5 311,1 31 7,0
Note: These values are only setting indications applicable to softeners with VK valves. They are determined for standard resin use and for an
average temperature of 15°C. They must be adapted in accordance with the specific location of every installation. In any case they do not involve Hytek’s responsibility.
Injector
Drain flow regulator (DFR) Range
Cappers | Tel : +33 (0) 473 94 84 87 | www.cappers.fr
Down- litre of resin
Valve Tank
Inje
ctor
Salt
Cycle
1
Cycle
2
Cycle
3
Cycle
4
Wat
er u
se
Back
was
h
Brin
ing
(dra
w)
Slow
rins
e
Rapi
d rin
se
Tank
refil
l
VK32
-1
VK32
-2
VK40
-1
VK40
-2
VK50
-2
Dim
ensio
ns
Volu
me
(L)
Open
ing
Resin
(L)
Inje
ctor
n°
Salt
volu
me
(kg)
Brin
e vo
lum
e
Tim
e
Flow
Tim
e
Flow
Tim
e dr
aw +
slow
rins
e
Tim
e
Volu
me
Tim
e
Flow
DFR
m³/
h
12 X 48 79 2½'' 55 1 8,8 27,5 5 1,9 14,5 1,8 43 5 24,4 6,1 0,8 236 14 X 52 115 2½'' 75 2 12 37,5 5 2,4 15,6 3,3 47 5 33,3 8,3 1,1 371 14 X 65 148 2½'' or 4'' 100 2 16 50,0 5 2,4 20,8 3,3 63 5 44,4 11 1,1 434
16 X 65 194 2½'' or 4'' 125 3 20 62,5 5 4,0 15,6 4,5 47 5 55,6 14 1,6 533
16 X 65 194 2½'' or 4'' 125 3 20 62,5 5 4,0 15,6 4,5 47 5 55,6 6 1,6 533 18 X 65 257 4'' 170 3 27 85,0 8 4,0 21,3 4,5 64 6 75,6 8 1,6 736 21 X 62 330 4'' 220 4 35 110,0 5 5 97,8 10 2,3
24 X 72 473 4'' 310 5 50 155,0 5 5 137,8 14 3,3
30 X 72 697 4'' 460 6 74 230,0 5 5 204,4 20 5,2
36 X 72 1011 4'' 700 7 112 350,0 5 5 311,1 31 7,0
Note: These values are only setting indications applicable to softeners with Cappers valves. They are determined for standard resin use and for an average temperature of 15°C. They must be adapted in accordance with the specific location of every installation. In any case they do not involve Cappers’ responsibility.
Drain flow regulator (DFR) Range
Injector
Down-flow standard settings for 120 g of salt per litre of resin
Valve Tank
Inje
ctor
Salt
Cycle
1
Cycle
2
Cycle
3
Cycle
4
Wat
er u
se
Back
was
h
Brin
ing
(dra
w)
Slow
rins
e
Rapi
d rin
se
Tank
refil
l
VK32
-1
VK32
-2
VK40
-1
VK40
-2
VK50
-2
Dim
ensio
ns
Volu
me
(L)
Open
ing
Resin
(L)
Inje
ctor
n°
Salt
volu
me
(kg)
Brin
e vo
lum
e
Tim
e
Flow
Tim
e
Flow
Tim
e dr
aw +
slow
rins
e
Tim
e
Volu
me
Tim
e
Flow
DFR
m³/
h
12 X 48 79 2½'' 55 1 6,6 20,6 5 1,9 10,9 1,8 33 5 18,3 4,6 0,8 210 14 X 52 115 2½'' 75 2 9 28,1 5 2,4 11,7 3,3 35 5 25,0 6,3 1,1 324 14 X 65 148 2½'' or 4'' 100 2 12 37,5 5 2,4 15,6 3,3 47 5 33,3 8 1,1 371
16 X 65 194 2½'' or 4'' 125 3 15 46,9 5 4,0 11,7 4,5 35 5 41,7 10 1,6 466
16 X 65 194 2½'' or 4'' 125 3 15 46,9 5 4,0 11,7 4,5 35 5 41,7 4 1,6 466 18 X 65 257 4'' 170 3 20 63,8 8 4,0 15,9 4,5 48 6 56,7 6 1,6 645 21 X 62 330 4'' 220 4 35 110,0 5 5 97,8 10 2,3
24 X 72 473 4'' 310 5 50 155,0 5 5 137,8 14 3,3
30 X 72 697 4'' 460 6 74 230,0 5 5 204,4 20 5,2
36 X 72 1011 4'' 700 7 112 350,0 5 5 311,1 31 7,0
Note: These values are only setting indications applicable to softeners with VK valves. They are determined for standard resin use and for an
average temperature of 15°C. They must be adapted in accordance with the specific location of every installation. In any case they do not involve Hytek’s responsibility.
Injector
Drain flow regulator (DFR) Range
Nota: i valori sopra indicati sono riferiti esclusivamente ad addolcitori con valvole VK e sono riferiti a test eseguiti su resina standard ad una temperatura media di 15 ° C. I dati possono variare in riferimento alle caratteristiche specifiche dell’ impianto dove ven-gono montate le valvole VK. In ogni caso la tabella sopra è indicativa ed esonera Hytek da ogni responsabilità.Note: These values are only setting indications applicable to softeners with VK valves. They are determined for standard resin use and for an average temperature of 15°C. They must be adapted in accordance with the specific location of every installation. In any case they do not involve Hytek’s responsability.
Impostazioni Down-Flow basate su 120 g di sale per litro di resina Down-Flow standard settings for 120 g of salt per litre of resin.
Iniettore/Injector
Impostazioni Down-Flow basate su 160 g di sale per litro di resina Down-Flow standard settings for 160 g of salt per litre of resin.
Nota: i valori sopra indicati sono riferiti esclusivamente ad addolcitori con valvole VK e sono riferiti a test eseguiti su resina standard ad una temperatura media di 15 ° C. I dati possono variare in riferimento alle caratteristiche specifiche dell’ impianto dove ven-gono montate le valvole VK. In ogni caso la tabella sopra è indicativa ed esonera Hytek da ogni responsabilità.Note: These values are only setting indications applicable to softeners with VK valves. They are determined for standard resin use and for an average temperature of 15°C. They must be adapted in accordance with the specific location of every installation. In any case they do not involve Hytek’s responsability.
Tipi di regolatori di scarico (DFR)/Drain flow regulator (DFR)
Down-flow standard settings for 120 g of salt per litre of resin
Valve Tank
Inje
ctor
Salt
Cycle
1
Cycle
2
Cycle
3
Cycle
4
Wat
er u
se
Back
was
h
Brin
ing
(dra
w)
Slow
rins
e
Rapi
d rin
se
Tank
refil
l
VK32
-1
VK32
-2
VK40
-1
VK40
-2
VK50
-2
Dim
ensio
ns
Volu
me
(L)
Open
ing
Resin
(L)
Inje
ctor
n°
Salt
volu
me
(kg)
Brin
e vo
lum
e
Tim
e
Flow
Tim
e
Flow
Tim
e dr
aw +
slow
rins
e
Tim
e
Volu
me
Tim
e
Flow
DFR
m³/
h
12 X 48 79 2½'' 55 1 6,6 20,6 5 1,9 10,9 1,8 33 5 18,3 4,6 0,8 210 14 X 52 115 2½'' 75 2 9 28,1 5 2,4 11,7 3,3 35 5 25,0 6,3 1,1 324 14 X 65 148 2½'' or 4'' 100 2 12 37,5 5 2,4 15,6 3,3 47 5 33,3 8 1,1 371
16 X 65 194 2½'' or 4'' 125 3 15 46,9 5 4,0 11,7 4,5 35 5 41,7 10 1,6 466
16 X 65 194 2½'' or 4'' 125 3 15 46,9 5 4,0 11,7 4,5 35 5 41,7 4 1,6 466 18 X 65 257 4'' 170 3 20 63,8 8 4,0 15,9 4,5 48 6 56,7 6 1,6 645 21 X 62 330 4'' 220 4 35 110,0 5 5 97,8 10 2,3
24 X 72 473 4'' 310 5 50 155,0 5 5 137,8 14 3,3
30 X 72 697 4'' 460 6 74 230,0 5 5 204,4 20 5,2
36 X 72 1011 4'' 700 7 112 350,0 5 5 311,1 31 7,0
Note: These values are only setting indications applicable to softeners with VK valves. They are determined for standard resin use and for an
average temperature of 15°C. They must be adapted in accordance with the specific location of every installation. In any case they do not involve Hytek’s responsibility.
Injector
Drain flow regulator (DFR) Range
Tipi di regolatori di scarico (DFR)/Drain flow regulator (DFR)
VK50 - 2”HYK-VALVES
DIAGRAMMI DI FLUSSO / FLOW DIAGRAMS
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
bars
bars
bars
bars
bars
bars
bars
bars
l/mn
l/mn
l/mn
l/mn
l/mn
l/mn
l/mn
l/mn
l/mn
l/mn
2,0
2,0
2,0
2,0
3,0
3,0
3,0
3,0
4,0
4,0
4,0
4,0
5,0
5,0
5,0
5,0
6,0
6,0
6,0
6,0
7,0
7,0
7,0
7,0
8,0
8,0
8,0
8,0
2,0
2,0
2,0
2,0
3,0
3,0
3,0
3,0
4,0
4,0
4,0
4,0
5,0
5,0
5,0
5,0
6,0
6,0
6,0
6,0
7,0
7,0
7,0
7,0
8,0
8,0
8,0
8,0
8,0
8,0
8,0
8,0
9,0
9,0
9,0
9,0
Brine draw Slow rinse
Injector n°1
Injector n°2
Injector n°3
Injector n°4
SCA industrial - Flow diagrams
Slow rinseBrine draw
Slow rinse
Slow rinse
Brine draw
Brine draw
2
2
2
2
2
2
3
3
3
3
3
3
4
4
4
4
4
4
5
5
5
5
5
5
6
6
6
6
6
6
7
7
7
7
7
7
8
8
8
8
8
8
bars
bars
bars
bars
bars
bars
l/mn
l/mn
l/mnl/mn
l/mn
l/mn
l/mn
8,0
8,0
8,0
10,0
10,0
10,0
12,0
12,0
12,0
14,0
14,0
14,0
16,0
16,0
16,0
18,0
18,0
18,0
20,0
20,0
20,0
6,0
6,0
6,0
8,0
8,0
8,0
10,0
10,0
10,0
12,0
12,0
12,0
14,0
14,0
14,0
16,0
16,0
16,0
18,0
18,0
18,0
20,0
20,0
20,0
Brine draw Slow rinse
Injector n°5
Injector n°6
Injector n°7
SCA industrial - Flow diagrams
Slow rinseBrine draw
Slow rinseBrine draw
4,0
4,0
4,0
MPX HYK-VALVES
SISTEMI MULTIPLEX WIRELESS VK40 & VK50 MPX/ VK40 & VK50 MPX WIRELESS MULTIPLEX SYSTEMS
SISTEMI MULTIPLEX VK40-3 & VK50-3Le valvole della serie VK40 & VK50, permettono la realizzazione di impianti multiplex fino ad un massimo di 5 valvole collegate insieme. Un sistema di comunicazione Wireless che lavora ad una frequenza di 868 MHz unito al protocollo RS485, fanno dei sistemi multiplex VK40 & VK50 i leader nel loro campo.Il sistema Wireless semplifica l’ interconnessione fra le val-vole (nessun utilizzo di cavi aggiunti) e il Network permette di lavorare sia in modalità in serie che in parallelo.Specifiche valvole- Materiale del corpo valvola: _______________________ Noryl ® - Entrata / Uscita: __________________________1 ¼ “- 1“1/2- 2” BSPCaratteristiche- Network: _________________________________ Wireless 868 MHz - Protocollo industriale di sicurezza: ____________________ RS485- Sistemi: ____ fino a 3 sistemi da 2 - 5 valvole senza interferenze- Programmazione: ___________________ semplificata e intuitiva- Modalità di funzionamento: ___________ alternato o parallelo- Rigenerazione: _______________ DF o UF (con lo stesso pistone)- Trasformatore di sicurezza: __________ permette di ultimare la rigenerazione anche in assenza di corrente elettrica (autono-mia 12 ore circa)- Opzione relè ausiliari: __2 relè aux in 1 unica scheda(VK0200)- Possibilità filtro: __________________________________________ Sì- Aspirazione e lavaggio lento: _________ con acqua addolcitaMicroprocessore- Visualizzazione: ____ display digitale retro illuminato, 4, 5 cifre- Salvaguardia parametri: ___ Back-up tramite condensatore- Alimentazione elettrica: ______________ 230 V / 7,5V – 2 A – DC - Parametri impostabili: Ora del giorno, ora di rigenerazione, tempi dei cicli, capacità ciclica, forzatura a tempo, riserva. - Lettura: Volume restante, defalco del tempo, posizione del ciclo in corso.- Rigenerazione: a giorni fissi, a giorni selezionabili, volumetrica ritardata o immediata, manuale- Modalità Rigenerazione: Up Flow, Down Flow, Filtro, Salamoia variabilePressione- Idrostatica: ________________________________________ 24 bar- Servizio: _________________________________________ 2 a 8 bar- Temperatura: ____________________________________1 a 45°C- Test pressione: __ 1-14 bar (250.00 cicli), 1-24 bar (70.000 cicli) Opzioni- Relè Esterno (VK0200)- Acqua Calda - Valvola filtro- SBV di sicurezza- Attacco Side MountCertificati- Conformità Regolamento CE bassa tensione- CE - RoHS- ACS : 13 ACC LY 805 * Per sistemi con vasca di accumulo contattare l’ ufficio tecnico Hytek
MULTIPLEX SYSTEMS VK40-3 & VK50-3VK40 & VK50 series valves, allow to realize multiplex plants up to a maximum of 5 valves connected togheter. A Wireless comunication system that woks in 868 MHz frequency and a RS485 protocol, make multiplex systems VK40 & VK50 the lead-ers in their field. Wireless system semplify the interconnection between the valves (no wire add) and the Network allow to work in series or in parallel mode.Specifiche valvole- Valve material:_____________ _______________________ Noryl ® - Inlet / outlet:__ __________________________1 ¼ “- 1“1/2- 2” BSPGeneral Features:- Network: _________________________________ Wireless 868 MHz - Industrial afe communication protocol: _______________ RS485- Systems: ____ up to 3 systems, 2 - 5 valves without interference- Programmation: _________________________ easy and intuitive- Operation mode: _____________________ Alternate or parallel- Rigeneration: _______________ DF or UF (with the same piston)- Secured power supply: ______ it allows to finish the rigenera-tion in case of power failure (about 12 hours autonomy)- Relay Aux option: __2 relays aux in unique electronic (VK0200)- Filter option: __________________________________________ Yes- Brine and slow rinse: _______________ with with softened waterMicroprocessor- Display: _________________ Large backlight display - 4, 5 digits- Parameter backup: ____________________ Back-up Capacitor - Power supply: _______________________ 230 V / 7,5V – 2 A – DC - Adjustable parameters: time of day, time of regeneration, cycles time, cyclical capacity, time forcing, reserve.- Reading: volume remaining, remaining time, cycle in pro-gress.- Regeneration: Hours, Timeclock, Meter delayed or immedi-ate, manual.- Regeneration Mode: Downflow / Upflow, Filter, Variable Brin-ingPressure- Hydrostatic:_______________________________________ 24 bar- Working:________________________________________ 2 to 8 bar- Temperature:____________________________________1 to 45°C- Pressure Test:_1-14 bar (250.00 cycles), 1-24 bar (70.000 cycles) Options- External Relay (VK0200)- Filter valve- SBV Safety brine Valve- Side Mount adapterCertificates- Compliant to CE low voltage regulations - CE - RoHS- ACS : 13 ACC LY 805 * For systems with storage tank pls. contact Hytek technical department