Uttarakhand Technical University Dehradun Evaluation...
25
Uttarakhand Technical University Dehradun Evaluation Scheme and Syllabus For B. Tech. First Year Common to All Branches (Effective from Session-2016-17)
Transcript of Uttarakhand Technical University Dehradun Evaluation...
Uttarakhand Technical University
Dehradun
Evaluation Scheme and Syllabus
For
B. Tech. First Year
Common to All Branches
(Effective from Session-2016-17)
Uttarakahand Technical University, Dehradun
Common to All Branches
Program: B. Tech Year: 1st Semester: I
SCHEME & EVALUATION PATTERN
S.
No.
Subject/
Lab
Code
Subject/
Lab Name Credit
PERIOD EVALUATION
Grand
Total L T P CT A&Q ATT Total
External
Theory /
Lab
Marks
1 TMA
101
Engg.
Mathematics-I 4 3 1 0 30 10 10 50 100 150
2
TPH 101
/
TCY 101
Engg.
Physics/Engg.
Chemistry
4 3 1 0 30 10 10 50 100 150
3
TEE 101
/
TME 101
Basic Electrical
Engg./Basic
Mechanical Engg.
4 3 1 0 30 10 10 50 100 150
4 THM
101
Basic Technical
Communication 3 3 0 0 30 10 10 50 100 150
5
TCS 101/
TEC 101
Fundamentals of
Computer &
Programming/
Fundamental of
Electronics Engg.
4 3 1 0 30 10 10 50 100 150
6 TES 201 Environmental
Studies - 2 - - - - - - - -
7
PPH 101
/
PCY 101
Engg. Physics
Lab/ Engg.
Chemistry Lab
2 0 0 2 - 15 10 25 25 50
8
PEE 101
/
PME 101
Basic Electrical
Engg Lab/ Basic
Mechanical Engg
Lab
2 0 0 2 - 15 10 25 25 50
9 PEC 101/
PCS 101
Fundamental of
Electronics Engg.
Lab / Computer
Progm. Lab
2 0 0 2 - 15 10 25 25 50
10
PWS
101/PED
101
Workshop
Practice/ Engg.
Drawing
2 0 0 2 - 15 10 25 25 50
11 Language Lab 2 0 0 2 - 30 20 50 50
28 1000
L- No. of Lecture hours per week CT- Class Test
T- No. of Tutorial hours per week A&Q - Assignment & Quiz
P- No. of Practical hours per week ATT - Attendance
Uttarakahand Technical University, Dehradun
Common to All Branches
Program: B. Tech Year: 1st Semester: I
SCHEME & EVALUATION PATTERN
S.N Subject/
Lab Code
Subject/
Lab Name Credit
PERIOD EVALUATION
Grand
Total L T P CT A&Q ATT TOTAL
External
Theory /
Lab
Marks
1 TMA 201 Engg.
Mathematics-II 4 3 1 0 30 10 10 50 100 150
2 TCY 201
/TPH 201
Engg. Chemistry
/Engg. Physics 4 3 1 0 30 10 10 50 100 150
3 TME 201
/TEE 201
Basic Mechanical
Engg. /Basic
Electrical Engg.
4 3 1 0 30 10 10 50 100 150
4 THM 201
Advanced
Technical
Communication
3 3 0 0 30 10 10 50 100 150
5
TCS 201
/TEC 201
Fundamentals of
Computer &
Programming
/Fundamental of
Electronics Engg.
4 3 1 0 30 10 10 50 100 150
6 TES 201 Environmental
Studies - 2 - - - - - - - -
7 PCY 201
/PPH 201
Engg. Chemistry
Lab/ Engg.
Physics Lab
2 0 0 2 - 15 10 25 25 50
8 PME 201
/PEE 201
Basic Mechanical
Engg Lab/ Basic
Electrical Engg
Lab
2 0 0 2 - 15 10 25 25 50
9 PCS 201/
PEC 201
Computer Progm.
Lab /Fundamental
of Electronics
Engg. Lab
2 0 0 2 - 15 10 25 25 50
10
PED201/
PWS201
Engg. Drawing
/Workshop
Practice
2 0 0 2 - 15 10 25 25 50
11
Discipline/
General
proficiency
50 50
28 1000
L- No. of f Lecture hours per week CT- Class Test
T- No. of Tutorial hours per week A&Q - Assignment & Quiz
P- No. of Practical hours per week ATT - Attendance
Syllabus of Course
Name of the Department: Applied Science
1. Subject Code: TMA-101
2. Subject Title: ENGINEERING MATHEMATICS-I
3. Credits: 4
4. Contact Hours:
5. Examination Duration (Hrs) :
6. Details:
Unit Course Contents
No of
Contact
Hours
Unit -I
Matrices
Types of Matrices, Inverse of a matrix by elementary transformations, Rank of a matrix
(Echelon & Normal form), Linear dependence, Consistency of linear system of equations and
their solution, Characteristic equation, Eigen values and Eigen vectors, Cayley-Hamilton
Theorem, Diagonalization, Complex and Unitary Matrices and its properties
8
Unit-II
Differential Calculus-I
Successive Differentiation, Leibnitz’s theorem, Limit , Continuity and Differentiability of
functions of several variables, Partial derivatives, Euler’s theorem for homogeneous
functions, Total derivatives, Change of variables
8
Unit-III
Differential Calculus-II
Taylor’s and Maclaurin’s Theorem, Expansion of function of several variables, Jacobian,
Approximation of errors, Extrema of functions of several variables, Lagrange’s method of
multipliers (Simple applications).
8
Unit-IV
Multiple Integrals
Double and triple integrals, Change of order of integration, Change of variables, Application
of integration to lengths, Surface areas and Volumes – Cartesian and Polar coordinates. Beta
and Gamma functions, Dirichlet’s integral and its applications.
8
Unit-V
Vector Calculus
Point function, Gradient, Divergence and Curl of a vector and their physical interpretations,
Vector identities, Tangent and Normal, Directional derivatives. Line, Surface and Volume
integrals, Applications of Green’s, Stoke’s and Gauss divergence theorems (without proof).
8
Total Lectures 40
Text Books:
1. E. Kreyszig, Advanced Engineering Mathematics, John-Wiley & Sons
2. B. V. Ramana, Higher Engineering Mathematics, Tata Mc Graw- Hill Publishing Company Ltd.
3. R. K. Jain & S.R.K. Iyenger, Advance Engineering Mathematics, Narosa Publishing House.
Reference Books:
1. B.S. Grewal, Higher Engineering Mathematics, Khanna Publishers.
2. Peter V. O’ Neil, Advanced Engineering Mathematics, Thomas ( Cengage) Learning.
3. Thomas & Finley, Calculus, Narosa Publishing House
4. Rukmangadachari, Engineering Mathematics – I, Pearson Education.
5. A. C. Srivastava & P. K. Srivastava, Engineering Mathematics, Vol - I, PHI Learning Pvt. Limited, New Delhi
L 3 T 1 P 0
Theory 03 Practical 00 Sessional 02
SYLLABUS OF COURSE
NAME OF THE DEPARTMENT: Applied Science
1. Subject Code: TPH-101/201
2. Subject Title: ENGINEERING PHYSICS
3. Credits: 4
4. Contact Hours:
5. Examination Duration (Hrs) :
6. Details:
Unit Course Contents
No of
Contact
Hours
Unit -I
RELATIVISTICS MECHANICS –
Inertial and Non-Inertial frames, Postulates of Special theory of Relativity, Galilean and
Lorenty Transformation, Length Contraction, Time Dilation, Addition of Velocities,
Variation of Mass With Velocity, Concept of Rest Mass of Photon.
RADIATION –
Concept of Black Body, Energy Spectrum of Black Body Radiation, Compton Effect.
8
Unit-II
INTERFERENCE –
Coherent Sources, Condition of Interference, Displacement of Fringes, Interference in Thin
Films Wedge Shaped Film, Newton’s Rings.
DIFFRACTION –
Single and N-Slit Diffraction, Diffraction Grating, Raleigh’s Criterion of Resolution,
Resolving Power of Grating.
8
Unit-III
Polarization: Phenomenon of Double Refraction, Ordinary and Extra-Ordinary Rays, Nicol Prism,
Production and Analysis of Plane, Circularly and Elliptically Polarized Light, Optical
Activity, Retardation Plate, Hall Effect.
LASER –
Principle of Laser Action, Spontaneous and Stimulated Emission of Radiation, Population
Inversion, Einstein’s Coefficients, Construction and Working of He-Ne and Ruby Laser.
8
Unit-IV
ELECTROMAGNETIC –
Ampere’s Law and Displacement Current, Maxwell’s Equations in Integral and Differential
Forms, Electromagnetic Wave Propagation in Free Space and Conducting Media, Pointing
Theorem.
MAGNETIC PROPERTIES OF MATERIALS –
Basic Concept of Para- Dia and Ferro – Magnetism, Phenomenon of Hysteresis and its
Applications.
8
Unit-V
SUPERCONDUCTIVITY:
Essential Properties of Superconductors (Zero Resistivity), London Equations, Meissner
Effect, Critical Field, Critical Current Isotope Effect, Heat Capacity, Type I and Type II
Superconductors, Characteristics of Superconductors in Superconducting State, Applications
of Superconductors.
WAVE MECHANICS:
Wave Particle Duality, De Broglie Concept of Matter Waves, Heisenberg Uncertainty
Principle, Schrödinger’s Wave Equation (Time Dependent And Time Independent) – Particle
in One Dimensional Potential Box.
8
Total Lectures 40
REFERENCE BOOKS:
1. Robert Resnick, Introduction To Special Theory of Relativity, Wiley
2. Wehr Richards & Adia, Physics of Atoms,
3. Halliday, Fundamentals of Physics, Wiley India
4. William Hayt, Engineering Electromagnetics, 7th Ed., TMH
5. Ashutosh Asthana, Engg. Physics, BS Publication, Hyderabad
L 3 T 1 P 2
Theory 03 Practical 03 Sessional 02
Syllabus of Course NAME OF THE DEPARTMENT: Applied Science
1. Subject Code: TCY-101/201
2. Subject Title: ENGINEERING CHEMISTRY
3. Credits: 4
4. Contact Hours:
5. Examination Duration (Hrs) :
6. Details:
Unit Course Contents
No of
Contact
Hours
Unit -I
GENERAL & ORGANIC CHEMISTRY
Valence bond theory, Molecular orbital theory and its application, liquid crystals & its
application, Reaction intermediates, Attacking reagents, inductive effect, electromeric,
mesomeric (resonance) effect, Hyper conjugation, reaction intermediates, Types of organic
reaction (substitution, addition, elimination reaction & organic rearrangements), Optical
isomerism, E-Z nomenclature, R-S configuration, Band Theory of solids, Saytzeff’s Rule,
Fullerenes & There application. Bragg’s Law.
8
Unit-II
PHYSICAL & WATER CHEMISTRY
Rate of reaction, order & molecularity of reaction, Zero order, First Order, Second order
reaction, Steady state approximation, concept of activation energy, cell potential, liquid
junction potential, conductance & its variation with dilution, Nernst distribution law and its
application, Corrosion and its type, Mechanism & control, Hardness of water, Disadvantage
of hard water, Water softening methods (Lime-Soda process, Ion exchange process, Zeolite
process, Reverse osmosis, Calgon Process), Treatment of boiler feed water. Concepts of
nano-materials and its applications
8
Unit-III
CHEMISTRY OF ENGINEERING MATERIALS
Introduction & classification of polymers, Types of Polymerization, Rubber, vulcanization,
Resins (Phenol Formaldehyde), Conducting and Biodegradable polymers, Pyroceramics,
Toughened glass, Strengthening of glass, Refractories, Nano Composites, Fe, Al, Cu, Pb &
Zn alloys, Setting and hardening of cement, applications of cement. Plaster of Paris.
8
Unit-IV
FUELS & COMBUSTION
Classification of Fuels, calorific value of fuel, gross & net calorific value, determination of
calorific value using Bomb calorimeter, Coal, Biomass and Biogas, Bio Fuel, Introduction of
Lubricants, Mechanism of Lubrication, Classification of Lubricant, Bio Lubricant, Flash and
Fire Point, Pour Point, Cloud Point, Aniline point, Viscosity index.
8
Unit-V
ANALYTICAL METHODS AND APPLICATIONS
Titrimetric analysis with reference to acid-base, redox, precipitation and complexometric
titrations. Elementary ideas and simple applications of UV, visible, mass and NMR spectral
techniques, Differential Thermal Analysis (DTA), Differential scanning Calorimetry (DSC)
and Thermo gravimetry (TGA).
8
Total Lectures 40
REFERENCE BOOKS 1. Sivasankar, Engineering Chemistry, TMH, New Delhi.
2. Morrisson & Boyd, Organic Chemistry, Pearson Publication.
3. Loudon, Organic Chemistry, Oxford University Press.
4. Engineering Chemistry – Wiley India
5. C Parameswara Murthy, C V Agrawal and etal., Engineering Chemistry, BS Publication, Hyderabad
L 3 T 1 P 2
Theory 03 Practical 03 Sessional 02
Syllabus of Course NAME OF THE DEPARTMENT: Electrical Engineering
1. Subject Code: TEE-101/201
2. Subject Title: BASIC ELECTRICAL ENGINEERING
3. Credits: 4
4. Contact Hours:
5. Examination Duration (Hrs) :
6. Details:
Unit Course Contents
No of
Contact
Hours
Unit -I
D.C. Network Theory :
Circuit theory concepts-Mesh and node analysis. Network Theorems-Super-position
theorem. Thevenin’s theorem, Norton’s theorem, Maximum, Power Transfer theorem, Star
Delta transformation.
Energy Conservation basics.
Steady State Analysis of A.C. Circuits : Sinusoidal and phasor representation of voltage and current: single phase A.C. circuit
behavior of resistance, inductance and capacitance and their combination in series &
parallel and power factor, series parallel resonance-band width and quality factor :
magnetic circuit.
8
Unit-II
Measuring Instruments:
Construction and principle of operation of voltage and current measuring instruments;
introduction to power and energy meters, Construction and working principles of PMMC
and moving iron type voltmeters & ammeters, Single phase dynamometer wattmeter, Use
of shunts and multipliers (Simple numerical problems on shunts and multipliers), Basics
of digital energy meter.
8
Unit-III Transformer:
Principle of operation, types of construction, phasor diagram, equivalent circuit, efficiency
and voltage regulation of single phase transformer, O.C. and S.C. tests.
8
Unit-IV
D.C. Machines
Principle of electromechanical energy conversion, types of DC. machines, E.M.F.
equation, Magnetization and load characteristics, losses and efficiency, Starter and speed
control of D.C. motors, their applications.
Synchronous Machines: Principle of Operation of Alternator and synchronous motor 2
8
Unit-V
Three phase induction Motor
Principle of operation, types and methods of starting, slip-torque characteristics,
applications.
Single phase Motors: Principle of operation and methods of starting of induction motor.
8
Total Lectures 40
REFERENCE BOOKS 1. V. Del Toro., Principles of electrical Engineering, Prentice hall International.
2. W.H. Hayt & J.E. Kemmerly, Engineering Circuit Analysis, Mc Graw Hill.
3. I.J. Nagrath, Basic Electrical Engineering, Tata Mc. Graw Hill.
4. A.E. Fitgerald, D.E., Higginbotham and A Grabel, “Basic Electrical Engineering, McGraw Hill.
5. H. Cotton, Advanced Electrical Technology, Wheeler Publishing
L 3 T 1 P 2
Theory 03 Practical 03 Sessional 02
Syllabus of Course NAME OF THE DEPARTMENT: Mechanical Engineering
1. Subject Code: TME-101/201
2. Subject Title: BASIC MECHANICAL ENGINEERING
3. Credits: 4
4. Contact Hours:
5. Examination Duration (Hrs) :
6. Details:
Unit Course Contents
No of
Contact
Hours
Unit -I
Fundamental Concepts and Definitions:
Definition of thermodynamics, System, Surrounding and universe, Phase, Concept of
continuum, Macroscopic & microscopic point of view. Density, Specific volume, Pressure,
temperature. Thermodynamic equilibrium, Property, State, Path, Process, Cyclic and non
cyclic processes, Reversible and irreversible processes, Quasi static process, Energy and its
forms, Enthalpy. Zeroth law: Zeroth law, Different temperature scales and temperature
measurement.
First law: First law of thermodynamics. Processes - flow and non-flow, Control volume,
Flow work and non-flow work, Steady flow energy equation.
8
Unit-II
Second law:
Limitations of first law of thermodynamics, Essence of second law, Thermal reservoir, Heat
engines. COP of heat pump and refrigerator. Statements of second law and their equivalence,
Carnot cycle, Carnot theorem, Concept of entropy, Application of Thermodynamics and
Thermodynamic temperature scale, Clausius inequality.
8
Unit-III
Internal Combustion Engines:
Classification of I.C. Engines and their parts, working principle and comparison between 2
stroke and 4 stroke engine, difference between SI and CI engines. Pv and T-s diagrams of
Otto and Diesel cycles, comparison of efficiency, Comparison of Auto & Diesel Engine.
Properties of Pure Substance: P-v, T-s and h-s diagram, dryness fraction and steam tables.
Rankine Cycle.
8
Unit-IV
Force system and Analysis
Basic concept: Review of laws of motion, transfer of force to parallel position, resultant of
planer force system, Free Body Diagrams, Equilibrium. Concept of Centre of Gravity,
Centroid Area and Moment of Inertia- Perpendicular axis theorem and Parallel axis
theorem Friction: Introduction, Laws of Coulomb friction, Equilibrium of bodies involving
dry fiction, Ladder Friction.
Structure Analysis
Beams: Types of beams, Statically Determinate Beams, Shear force and bending moment in
beams, Relationships between loads, Theory of shear and bending moment. Trusses:
Introduction, Simple Trusses, Determination of forces in simple truss members, Method of
joints
8
Unit-V
Stress and Strain Analysis
Simple stress and strain: Introduction, Normal shear stresses, Stress-strain diagrams for
ductile and brittle materials, Elastic constants, One dimensional loading of members of
varying cross section, Strain energy, Thermal stresses. Pure Bending of Beams: Introduction,
Simple bending theory, Stress in beams of different cross sections.
8
Total Lectures 40
REFERENCE BOOKS:
1. Agarwal, Basic Mechanical Engineering, Wiley India
2. J.P. Holman, Thermodynamics, Mc Graw Hill
3. Onkar Singh, S.S. Bhavikatti, Suresh Chandra, Introduction to Mechanical Engineering: Thermodynamics,
Mechanics and Strength of Materials, New Age International Publishers
4. R. Yadav, Thermodynamics and Heat Engines, Vol I & II (SI Edition) Central Publishing House
L 3 T 1 P 2
Theory 03 Practical 03 Sessional 02
Syllabus of Course NAME OF THE DEPARTMENT: Humanities
1. Subject Code: THM-101
2. Subject Title: Basic Technical Communication
3. Credits: 3
4. Contact Hours:
5. Examination Duration (Hrs) :
6. Pre-requisite (if any): Relevance of Technical Communication for Technocrats:
English Communication is an integral part of today’s life. The advent of new technologies has lead to the
rapid development of a global village. A budding technocrat must be equipped with English language
proficiency so that he / she can make a mark in this global village. Engineering students come from different
backgrounds with different mother tongues. It is Imperative for them to overcome their native accentual
patterns and gain proficiency in speaking Standard English. They also need to acquire optimum writing skills.
Hence proper training in English speaking and writing is necessary. This goes hand in hand with the
development of reading and listening skills. The course of Basic Technical Communication will help in the
development and improvement of the communication skills and linguistic competence of engineering
students.
7. Objectives of the Course:
a) To help students perform better in all academic subjects through greater command over the English
language.
b) To promote efficiency in English language with the development of the four skills of communication i.e.,
LSRW (Listening, Speaking, Reading and Writing).
c) To prepare students face the challenges of their professional lives in an increasingly globalized world.
8. Details:
Unit Course Contents No of
Contact
Hours
Unit -I
COMMUNICATION
1) Communication – Definition. Process of communication,
2) Types of communication—Verbal and Non-Verbal communication; Formal and
Informal communication (grapevine) and their significance.
3) Barriers to Communication—Semantic barriers, Physical barriers, Psychological
barriers, Interpersonal barriers and Organizational barriers. Language as a tool of
communication.
4) Importance of communication with reference to students, professionals business etc.
5) Style of Technical Communication. Features of Technical Writing.
Note: Classroom teaching should be activity based. The teachers should ask the
students to communicate in English and various activities can be given in the classroom.
The students can be asked to speak on any given topic and peer evaluation should be
done.
8
Unit-II
READING SKILLS
1. Importance of Reading Skills, Types of Reading Skills, Methods of Improving
Reading Skills, Objectives of Improving Reading Skills
2. Vocabulary Building: Antonyms, Synonyms, Homophones, Word formation (Prefixes
and Suffixes). One Word substitution,
3. Jargon/Technical Terminology – Use of Jargon and examples of Jargon.
4. Paragraph: Definition. Requirements of a paragraph -- Understanding, Unity,
Coherence and Emphasis in a paragraph. Identifying the Topic Sentence. Development
of a Paragraph using Deductive order, Inductive order, Chronological Order (Time
Order), Spatial Order (Space Order), Expository Order, Question and Answer Order,
Comparison and Contrast Order. Devices used to impart Coherence and Emphasis in a
Paragraph.
5. Analysis of a given Paragraph in terms of Unity, Coherence and Emphasis.
8
L 3 T 0 P 0
Theory 03 Practical 00 Sessional 02
6. Developing Reading Skills and Reading Comprehension through the study of thematic
and value based critical reading of the following essays –
A. Wings of Fire by Dr. A.P.J. Abdul Kalam
B. The Language of Literature and Science by A. Huxley
C. Man and Nature by J. Bronowski
D. Science and Survival by Barry Commoner
E. The Mother of the Sciences by A.J. Bahm.
Note: the students should be given various topics to develop paragraphs so that their
writing skills are developed
Unit-III
WRITING SKILLS.
1) Importance of Writing Skills, Types of Writing Skills, Methods for Improving
Writing Skills, Objectives of Improving Writing Skills
2) Functional Grammar- Parts of Speech, Tenses, Verb, Conditional Sentences
3) Common Grammatical Errors: Errors of Syntax, Concord etc.
4) Précis Writing
5) Letter writing: Formal and Informal Letters.
6) Developing Writing Skills through the study of thematic and value based critical
reading of the following short stories–
A. After Twenty Years by O. Henry
B. The Open Window by Saki (H.H. Munro)
Note: Emphasis should be on activities in the classroom..
8
Unit-IV
LISTENING SKILLS
1) Importance of Listening Skills, Process of listening, listening and hearing, Active and
Passive Listening. Types of Listening: Academic listening, Appreciative listening,
Attentive Listening, Critical Listening, and Discriminative listening etc.
2) Methods for Improving Listening Skills, Objectives of Improving Listening Skills.
3) Barriers to listening: Semantic barriers, Physical barriers, and Psychological barriers.
4) Listening Comprehension: Identifying general content, Identifying specific
information.
5) Listening for Note taking and drawing inferences.
6) Developing listening skills and listening comprehension through the study of
thematic and value based critical reading of the following one-act play.
A. The Refund by Fritz Karinthy
B. Poems by Ravindra Nath Tagore from Geetanjali
(i) Mind Without Fear
(ii) Leave This
(iii) Lamp of Love
7) Practice of Listening Skills through Language Laboratory
1. Listening to a recording of a telephone conversation for identifying specific
information as well as details.
2. Listening to a recording of a railway / airport announcement for selective listening
and identifying specific information.
3. Listening to a recording of a radio / television news bulletin for identifying specific
as well as over-all information
4. Listening to a recording of the description of a place, event or incident for note-
taking, identifying details, descriptions and overall idea.
5. Listening to a recording of a lecture / talk on for note taking and identifying facts and
drawing conclusions.
6. Listening to a recording of a television panel discussion on any topic for identifying
facts, analyzing those drawing inferences and explaining the conclusion of the
discussion in a logical manner.
7. Listening to passages that are read out for practicing note taking and identifying
general and detailed content.
8. Listening to dialogues that are read out for identifying specific, general and detailed
content.
8
Unit-V
SPEAKING SKILLS.
1. Importance of Speaking Skills, Types of Speaking, Methods for Improving Speaking
Skills, Objectives of Improving Speaking Skills
2. Organs of Speech, Mechanism of Speech.
3. Phonetics: Classification of English Sounds, Vowel (short vowels and long vowels),
Consonants, Diphthongs, Phonemes, Allophones, Phonetic transcription.
4. Syllable: Definition, Types of Syllable. Monosyllabic, Polysyllabic words etc.
5. Stress, Rhythm, Intonation: Rising Tone, Falling Tone and Rising-Falling Tone.
6. Everyday Conversation: Tips and characteristics of a good conversation. Common
manners and etiquette.
7. Debate, Making a speech, Role play,
8. Extempore, JAM Session (just a minute session).
8
Total Lectures 40
SUGGESTED REFERENCES BOOKS:
1. Tyagi & Misra: Basic Technical Communication, PHI, New Delhi.
2. Rizvi, Effective Technical Communication, TMH, New Delhi
3. Arora & Chandra, Improve your Writing, OUP, New Delhi.
4. A.S Hornby, Guide to Patterns & Usage in English, OUP, New Delhi.
5. Suresh Kumar & Sreehari, A Handbook for English Language, Cambridge
6. Norman Lewis, Word Power Made Easy, W.R Goyal Pub. & Distributors.
7. A Ruther Ford, Basic Communication Skills, Person Education, N. Delhi
8. Michael Swan, Practical English Usage, OUP, New Delhi.
9. Joans Daniel, English Pronouncing Dictionary, Cambridge
10. John Seely, The Oxford Guide to Writing and Speaking, OUP, Delhi
11. Mohammad Aslam, Introduction of English Phonetics and Phonology, Cambridge
Syllabus of Course NAME OF THE DEPARTMENT: Electronics Engineering
1. Subject Code: TEC-101/201
2. Subject Title: FUNDAMENTALS OF ELECTRONICS ENGINEERING
3. Credits: 4
4. Contact Hours:
5. Examination Duration (Hrs) :
6. Details:
Unit Course Contents
No of
Contact
Hours
Unit -I
SEMICONDUCTOR MATERIALS AND PROPERTIES: Group-IV materials, Covalent
bond, Electron-hole concepts Basic concepts of energy bands in materials, Concepts of
forbidden gap, Intrinsic and Extrinsic semiconductors, Donors and Acceptors impurities
P-N JUNCTION DIODE:P-N junction, depletion layer, V- I characteristics, Diode
resistance, Capacitance diode ratings (average current, repetitive peak current, non-repetitive
current, peak-inverse voltage).
8
Unit-II
DIODE APPLICATIONS: Rectifiers (half wave and full wave), calculation of transformer
utilization factor and diode ratings, Filter (C – filter), Calculation of ripple factor and Load
regulation, Clipping circuits, Clamping circuits, Voltage multipliers. BREAKDOWN
DIODES:
Breakdown mechanisms (Zener and Avalanche), Breakdown characteristics, Zener
resistance, Zener diode ratings, Zener diode application as shunt regulator
8
Unit-III
BIPOLAR JUNCTION TRANSISTOR: Basic construction, Transistor action, CB, CE and
CC configurations, Input/output Characteristics, Concept of Biasing of transistors- fixed bias,
Emitter bias, Potential divider bias.
TRANSISTOR AMPLIFIER: Graphical analysis of CE amplifier, Concept of voltage gain,
Current gain, re model (low frequency), Computation of Ai, Av, Ri, RO of single transistor
CE and CC amplifier configurations.
8
Unit-IV
FIELD EFFECT TRANSISTOR: JFET: Basic construction, Transistor action, Concept of
pinch off, Maximum drain saturation current, Input and Transfer characteristics,
Characteristics equation CG, CS and CD configurations, Introduction to self and fixed
biasing Computation of Av, Ri, Ro, of single FET amplifiers using CS configuration.
MOSFFT: Depletion and Enhancement type MOSFET Construction, operation and
Characteristics.
8
Unit-V
SWITCHING THEORY AND LOGIC DESIGN: Number systems, Conversions of bases,
Boolean algebra, Logic gates, Concept of universal gate, Concept of K- Map (upto four
variable).
Operational Amplifiers Introduction and Block diagram of Op-Amp, Concept of Ideal Operational Amplifier, Ideal
Op-Amp parameters, Ideal and practical characteristics of Op-Amp, Practical Op-Amp
Circuits (Inverting Amplifier, Non-Inverting Amplifier, Unity Gain Amplifiers, Summing
amplifier. Integrator, Differentiator)
8
Total Lectures 40
SUGGESTED REFERENCES BOOKS:
1. Tyagi & Misra: Basic Technical Communication, PHI, New Delhi.
2. Rizvi, Effective Technical Communication, TMH, New Delhi
3. Arora & Chandra, Improve your Writing, OUP, New Delhi.
4. A.S Hornby, Guide to Patterns & Usage in English, OUP, New Delhi.
5. Suresh Kumar & Sreehari, A Handbook for English Language, Cambridge
6. Norman Lewis, Word Power Made Easy, W.R Goyal Pub. & Distributors.
7. A Ruther Ford, Basic Communication Skills, Person Education, N. Delhi
8. Michael Swan, Practical English Usage, OUP, New Delhi.
9. Joans Daniel, English Pronouncing Dictionary, Cambridge
10. John Seely, The Oxford Guide to Writing and Speaking, OUP, Delhi 11. Mohammad Aslam, Introduction of English Phonetics and Phonology, Cambridge
Syllabus of Course
L 3 T 1 P 2
Theory 03 Practical 03 Sessional 02
NAME OF THE DEPARTMENT: Electronics Engineering
1. Subject Code: TEC-101/201
2. Subject Title: FUNDAMENTALS OF ELECTRONICS ENGINEERING
3. Credits: 4
4. Contact Hours:
5. Examination Duration (Hrs) :
6. Details:
Unit Course Contents
No of
Contact
Hours
Unit
I
Introduction to Computer & Basics of Programming:
Introduction to Computer: CPU organization, ALU, registers & memory. Number systems,
binary, octal & hexadecimal codes and their inter conversions. Data representation,
representation of signed & unsigned numbers in memory, IEEE representation of float numbers.
Introduction to Programming: Introduction to algorithm, flow chart & program. Programming
languages, High level, middle level & low level language. Introduction to the program editing
tools such as vi or MS-VC editors. Compilers & interpreters, The idea of program execution at
micro level. Introduction to operating systems such as DOS, Windows, UNIX etc. Generations
of Computer.
8
Unit
II
C Programming (Data Types, Variables, Operators, Control Statements):
Data types, Identifiers, Storage class, Constant, Operators, Binary arithmetic, Expression,
Statements, Console I/O statements, Decision control statements: if-else, switch-case,
Loop/Iteration control statements: while, do-while & for. Jump control statements: return, go to,
break, continue and comments.
8
Unit
III
Pointers: Memory addresses, Byte addressable memory, pointer variables, pointer operator,
pointer expression, pointer arithmetic, multiple indirection of pointers, Application of pointer.
Function: Importance of function in program/software development, function prototype,
function calls, call by value & call by reference/addresses, recursion, Dynamic memory
allocation/de-allocation functions (malloc, realloc, calloc and free), pointers to functions,
preprocessor directives.
8
Unit
IV
Array: Importance of array in programming, single dimensional arrays, two dimensional arrays,
multidimensional arrays & variable length arrays. Array of pointers & pointer to an array,
passing array to the function as an argument.
String: Definition of string, gets & puts function for string, string handling using library
functions (strlen, strcpy, strcmp, strcat, strupr, strlwr, etc), Array of strings, String with pointers.
8
Unit
V
Structure: Importance of structure, Declaration, assignment & accessing members of structure,
structure within structure, array of structures, pointer to structure, passing structure to the
function as an argument.
Union: Comparison of union with structure, role of union in programming, Limitation with
union.
Enumeration: Importance of enumeration in programming.
File Handling: Importance of file handling in software development, Streams and files, File
system basics, Representation of file in memory, Programs to read, write and update files using
library functions like fgetc, fputc, fread, fwrite, fseek, fprintf, fscanf, etc.
8
Total Lectures 40
List of References /Text Books
1. Dennis M. Ritchie, The C Programming Language
2. V. Rajaraman,[Computer Basics and C Programming, PHI
3. Yashwant Kanetkar, Let Us C, BPB
4. K.R. Venugopal, S.R. Prasad, Mastering C, TMH
5. A Behrouz, Forouzan & Richard F. Gilberg, Computer Science- A Structured Programming Approach Using
C, Thomson, [India Edition]
6. MK Sharma & MP Thapliyal, Fundamental of Computers & Concepts in C Programming, Firewall Media,
Delhi
PHYSICS PRACTICALS
(PPH-101/201)
L 3 T 1 P 2
Theory 03 Practical 03 Sessional 02
List of Experiments
2. To determine the wavelength of monochromatic light by Newton’s ring.
3. To determine the wavelength of monochromatic light with the help of Fresnel’s biprism.
4. To determine the focal length of two lenses by nodal slide and locate the position of cardinal
points.
5. To determine the wavelength of spectral lines using plane transmission grating.
6. To determine the specific resistance of the material of given wire using Carey Foster’s
bridge.
7. To determine the variation of magnetic field along the axis of a current carrying coil and then
to estimate the radius of the coil.
8. To calibrate the given ammeter and voltmeter.
9. To study the Hall effect and determine Hall coefficient, carnier density and mobility of a
given semiconductor material using Hall-effect set up.
10. To determine energy bank gap of a given semiconductor material.
11. To determine E.C.E. of copper using Tangent or Helmholtz galvanometer.
12. To draw hysteresis curve of a given sample of ferromagnetic material and from this to
determine magnetic susceptibility and permeability of the given specimen.
13. To determine the ballistic constant of a ballistic galvanometer.
14. To determine the viscosity of a liquid.
Note : Additional experiments may be added based on contents of syllabus.
CHEMISTRY PRACTICALS
(PCY-101/201)
List of Experiments
1. Determination of alkalinity in the given water sample.
2. Determination of temporary and permanent hardness in water sample using EDTA as standard
solution.
3. Determination of available chlorine in bleaching powder.
4. Determination of chloride content in the given water sample by Mohr’s method.
5. Determination of iron content in the given ore by using external indictor
6. Viscosity of an addition polymer like polyster by Viscometer.
7. Determination of iron concentration in sample of water by colorimetric method. The method
involves the use of KCNS as colour developing agent and the measurements are carried out at l max
480 nm. Note : The general procedure of estimation is given on pp653-8 of the textbook of
Quantitative Chemical Analysis by A.I. Vogel 6th Edition, Publisher : Pearson education Ltd. 2000)
8. Determination of heat of neutralization of Hydrochloric acid and Sodium hydroxide
9. Determination of amount of dissolved oxygen in water
10. Separation of metal ions by paper chromatography
11. Preparation of iodoform from acetone
12. Preparation of Sodium Cobaltinitrile salt.
13. Preparation of Resins
14. Element detection & functional group identification in organic compounds
Note : Additional experiments may be added based on contents of syllabus.
FUNDAMENTALS OF ELECTRICAL ENGINEERING PRACTICALS
(PEE-101/201)
List of Experiments
1. Verification of Network Theorems.
2. Study of diode characteristics. Study of phenomenon of resonance in RLC series and parallel circuit.
3. Measurement of power in a three phase circuit by two wattmeter method.
4. Measurement of efficiency of a single phase transformer by load test.
5. Determination of parameters and losses in a single phase transformer by OC and SC test.
6. Study of characteristic of DC shunt Motor.
7. Study of characteristic of AC Motor.
8. DC generator characteristics.
9. Speed control of dc shunt motor.
10. Study running and reversing of a three phase induction motor.
11. Study of a single phase energy meter.
Note: Additional experiments may be added based on contents of syllabus.
Wherever necessary use Breadboard.
MECHANICAL ENGINEERING PRACTICALS
(PME-101/201)
List of Experiments
1. Study of Steam engine and steam turbine models.
2. Study of 2-stroke and 4-stroke I.C.E. models.
3. Study of Fiat engine and/ or Diesel engine prototype.
4. Study of a vapour compression Refrigeration unit tutor/refrigerator.
5. Study of a window type air conditioner.
6. To conduct the tensile test on a UTM and determine ultimate Tensile strength, percentage elongation for
a steel specimen.
7. To conduct the compression test and determine the ultimate compressive strength for a specimen.
8. To conduct the Impact test (Izod / charpy) on the Impact testing machine and to find the impact strength.
9. To determine the value of acceleration due to gravity by Atwood’s Machine apparatus.
10. To verify the principle of moment by Bell Crank Lever Apparatus
11. To determine the moment of inertia of a flywheel apparatus about its axis of rotation
12. To verify Newton’s second law of motion by Fletcher’s Trolley apparatus
13. To find out coefficient of friction by combined inclined plane & friction slide apparatus
14. To determine the velocity ratio, mechanical advantage & efficiency of a single purchase crab apparatus
& draw graph between load vs effort, mechanical advantage and efficiency.
15. To determine the velocity ratio, mechanical advantage & efficiency of a double purchase crab apparatus.
FUNDAMENTALS OF ELECTRONICS ENGINEERING PRACTICALS
(PEC-101/201)
List of Experiments
1. Study of diode characteristics.
2. To study a half wave and full wave rectifier circuit.
3. Determination of ripple factor of capacitive and non capacitive filter for HW and FW diode rectifier
circuit.
4. Study of characteristics of Zener Diode as constant voltage.
5. Verification of Application of Zener Diode as shunt regulator.
6. Study of Clipper and Clamper Circuit with different waveforms.
7. Determination of characteristics of BJT in CB and CE configuration.
8. Determination of characteristics of FET in CS and CD configuration.
9. Study of BJT as single stage amplifier and determination of Ai, Vi, Ri and Ro.
10. Study of AND, NAND, OR, NOR and EXOR gates.
11. Verification of Universal gates.
Note: These practicals are to be implemented with bread board
FUNDAMENTALS OF COMPUTER & PROGRAMMING PRACTICALS
(PCS-101/PCS-201)
List of Experiments
SN PRACTICAL
TOPIC PROGRAM BASED ON
1 DOS Commands Practice of internal DOS commands
Unit-1 Practice of external DOS commands
2
Simple Arithmetic
operations using
various data types
Write a program (WAP) in C to convert a temperature (entered
from the keyboard) from Fahrenheit to Celsius and vice versa.
Unit-2
WAP in C to swap any two numbers entered from the keyboard
(with and without using third variable)
3 Operator WAP in C using conditional operator to determine whether an
entered year is leap year or not.
4 Decision Control
Statement
WAP in C to enter the marks of any five subjects of a student and
print the division secured by the students using if-else statement.
WAP in C to print corresponding days of a week using switch
case statement.
5 Loop Control
Statement
WAP in C to convert a decimal number to binary number and
vice versa using while loop.
WAP in C to print the factorial of a number entered from the
keyboard using do-while loop.
WAP in C to find out whether an entered number is prime or not
using for loop.
6 Pointer WAP in C to swap any two numbers using pointers.
Unit-3 7 Function WAP in C to print Fibonacci series using function.
8 Recursion WAP in C to print factorial of a number using recursion.
9 Array (1-D)
WAP in C to find greatest & smallest number from an array of
five integers.
Unit-4
WAP in C to print the sum of elements available in an array of
five floats.
WAP in C to copy all the elements from one array to another in
reverse order.
10 Array (2-D) WAP in C to print the addition & subtraction of the elements of
any two matrices.
11 String
WAP in C to use string functions like strlen, strcpy, strcat, etc.
WAP in C to check whether an entered string is palindrome or
not using string functions.
12 Structure WAP in C to enter the title, page and price of any three books
using array of structures then print the details of the books.
Unit-5
13 Enumeration WAP in C to print corresponding month of an entered year using
enumeration.
14 File Handling
WAP in C to print total number of characters, number of spaces,
number of tabs and number of new lines written in a text file
“A.TXT”
WAP in C to copy the contents a file “A.TXT” to another file
“B.TXT”
WAP in C to modify a particular word written at nth
Position in a file using fseek function.
WORKSHOP PRACTICE PRACTICALS
(PWS-101/201)
1. Carpentry Shop:
a) Study of tools and operation and carpentry joints.
b) Simple exercise using jack plain.
c) To prepare half- lap corner joint, mortise and tennon joints.
d) Simple exercise on woodworking lathe.
2. Fitting Bench Working Shop :
a) Study of tools and operations
b) Simple exercises involving filling work.
c) Making perfect male-female joint
d) Simple exercise involving drilling/tapping/dieing.
3. Black Smithy Shop :
a) Study of tools and operations
b) Simple exercises based on black smithy operations such as upsetting, drawing down, punching,
bending, fullering & swaging.
4. Welding Shop:
a) Study of tools and operations.
b) Simple butt joint.
c) Lap joint.
d) Oxy acetylene welding.
5. Sheet metal shop :
a) Study of tools and operations.
b) Making funnel complete with soldering.
c) Fabrication of tool box, tray, electrical panel box etc
6. Machine Shop:
a) Study of tools and operations.
b) Plane turning.
c) Step turning.
d) Taper turning
e) Threading.
f) Single point cutting tool grinding.
REFERENCES:
1. Hajra, Bose, Roy: Workshop Technology Vol 1 & 2, Media Promotors
2. Raghuvanshi B.S.: Workshop Technology, Vol 1 & 2, Dhanpatrai
ENGINEERING DRAWING PRACTICALS
(PED-101/201)
1. Introduction Graphics as a tool to communicate ideas, Lettering and’ dimensioning, Construction
of geometrical figures like pentagon and hexagon.
2. Orthographic Projection Principles of orthographic projections, Principal and auxiliary planes, First and
Third angle projections. Projection of points. Pictorial view. Projection of lines parallel to both the
planes. Parallel to one and inclined to other, Inclined to both the planes. Application to practical
problems. Projection of solid in simple position, Axis or slant edge inclined to one and parallel to other
plane, Solids lying on a face or generator on a plane. Sectioning of solids lying I various positions, True
shape of the section. Development of lateral surfaces, sheet metal
drawing.
3. Isometric Projection Principles of isometric projection, Isometric projection using box and offset
methods.
References:
1. Bhatt. N.D.: Elementary Engineering Drawing, Charothar Publishing.
2. Laxmi Narayan V & Vaish W. : A Text Book of Practical Geometry on Geometrical drawing
LANGUAGE LAB
PRACTICALS
1. Practicing the following modules through self- learning software:
a) Grammar with special emphasis on Tenses
b) Pronunciation: of consonants, vowels, syllables and individual words
c) Word Stress: based on accentual patterns
d) Rhythm in speech based on content words and strong words
e) Intonation: rising, falling and rising- falling tone
f) Pause groups
g) Speech making / public speaking
2. Introducing self and others keeping in mind kinesics.
3. Common conversation practice (making small talk etc.).
4. Asking for permission.
5. Making requests.
6. Describing events / people / places
7. Extempore.
8. JAM Session (Just a Minute Session).
9. Role play
10. Holding informal discussions.
11. Logical presentation of one’s views on a given topic.
12. Delivering a speech using Stress, Rhythm and Intonation.
13. Practicing the following modules through self- learning software:
a) Pronunciation: of consonants, vowels, syllables and individual words
b) Word Stress: based on accentual patterns
c) Rhythm in speech based on content words and strong words
d) Intonation: rising, falling and rising- falling tone
e) Pause groups
f) Presentation skills
14. Participating in Mock Interviews
15. Participating in Group Discussions
16. Giving Presentations keeping in mind Kinesics, Para language, and Proxemics
17. Participating in Role Play for enhancing interpersonal and corporate communication skills
Syllabus of Course NAME OF THE DEPARTMENT: Humanities
1. Subject Code: THM-201
2. Subject Title: ADVANCE TECHNICAL COMMUNICATION
3. Credits: 3
4. Contact Hours:
5. Examination Duration (Hrs) :
6. Pre-requisite (if any): Relevance of Technical Communication for Technocrats
English Communication is an integral part of today’s life. The advent of new technologies has lead to the
rapid development of a global village. A budding technocrat must be equipped with English language
proficiency so that he / she can make a mark in this global village.
Engineering students come from different backgrounds with different mother tongues. It is imperative for
them to overcome their native accentual patterns and gain proficiency in speaking Standard English. They also
need to acquire optimum writing skills. Hence proper training in English speaking and writing is necessary.
This goes hand in hand with the development of reading and listening skills. The course of Basic Technical
Communication will help in the development and improvement of the communication skills and linguistic
competence of engineering students.
7. Objectives of the Course:
a) To help students perform better in all academic subjects through greater command over the English
language.
b) To promote efficiency in English language with the development of the four skills of communication i.e.,
LSRW (Listening, Speaking, Reading and Writing).
c) To prepare students face the challenges of their professional lives in an increasingly globalised world.
8. Details:
Unit Course Contents
No of
Contact
Hours
Unit -I
TECHNICAL COMMUNICATION
1. Introduction to technical communication, types of technical communication, history of the
development of technical communication.
2. Difference between general and technical communication, importance of technical
communication.
3. Characteristic features of technical communication. Elements of style in technical
communication.
4. Technical communication: Definition, Oral and Written technical communication.
Difference between general writing and technical writing.
5. Computer-aided Technical Communication.
6. Style in Technical Communication. Features of technical writing.
7. Importance of Technical Communication
8. Process of preparing a technical document.
9. Elements, features and objectives of scientific articles, research papers, dissertation and
thesis.
Note: Emphasis should be on the practical use of Computer like MS Word, Office, Blog and
8
Unit-II
BUSINESS COMMUNICATION
1. Importance and Features of Business Communication
2. Business Correspondence – Principles, Features, Types, Format and layout of Business
letter.
3. Types of Business Correspondence – letters of Enquiry, Quotation, Order, Instructions,
Sales, Credit, Complaint, Collection etc.
4. Some more types of Business Correspondence -- Notice, Agenda, Minutes,
Memorandum.
5. Job Application letters -- Covering letter, Resume, Bio-data and C.V.
Note: Practical Exercises should be given to the students in the classroom.
8
L 3 T 0 P 0
Theory 03 Practical 00 Sessional 02
Unit-III
TECHNICAL PROPOSAL and TECHNICAL REPORT
1. Technical Proposal – Introduction, purpose, features, types, format, importance, process
of preparation. Writing technical proposals.
2. Technical Report -- Features, Types, Style, Format, Relevance. Writing Technical
Reports..
8
Unit-IV
LITERATURE
1. Critical reading and thematic, value-based study of the Novella, ‘Animal Farm’ by
George Orwell.
2. Critical review, study of theme, plot, symbolism, characterization, style of writing etc
8
Unit-V
SOFT SKILLS
This unit should be covered in classroom teaching as well as judicious use of language lab,
(There should be optimum use of software’s related to accent, presentation skills etc.)
1. Kinesics, Para language, Proxemics, Haptics, Chronomics
2. Presentation skills - Features, Types, Structure, Aids and Importance.
3. Interpersonal communication skills – Role of Personality and its various attributes like
EQ, attitude, motivation, stress management and accepting criticism in determining
efficacy of interpersonal communication.
4. Corporate communication skills – Role of business etiquette, conducting meetings,
managing conflict, negotiation, team spirit, decision-making, time management and
problem solving skills.
5. Group Discussion skills - Features and Importance
6. Facing Interviews - Interview Tips.
8
Total Lectures 40
Reference Books:
1. Gupta, Advanced Technical Communication, Cambridge University Press, N. Delhi
2. Sharma & Mishra, Communication Skills for Engineers and Scientists, PHI Learning, N. Delhi.
3. George Orwell, Animal Farm, Penguin Publishing Company, N. Delhi
4. Sharma & Mohan, Business Correspondence and Report Writing, TMH, N Delhi.
5. Rubens, Science & Technical Writing, Foundation books, Cambridge, N. Delhi
6. Daniel Riordan, Technical Communication, Cengage Learning, N. Delhi
7. Raman & Sharma, Technical Communication, OUP, N. Delhi
8. Wallace, Masters Personality Development, Cengage Learning, N. Delhi
9. Robert Barrass, Students Must Write, Foundation books, Cambridge,
Syllabus of Course NAME OF THE DEPARTMENT: Applied Science
1. Subject Code: TMA-201
2. Subject Title: ENGINEERING MATHEMATICS-II
3. Credits: 4
4. Contact Hours:
5. Examination Duration (Hrs) :
6. Details:
Unit Course Contents
No of
Contact
Hours
Unit -I
Ordinary Differential Equation Introduction of differential equation, Order and degree, Ordinary differential equation,
Exact differential equation, Linear differential equation of first order, Linear differential
equation of nth order with constant coefficient’s, Simultaneous linear differential equation,
Homogenous linear differential equation, Method of variation of parameters.
8
Unit-II
Laplace Transform and its Applications Laplace transform and its properties, Existence theorem, Laplace transform of derivatives
and integral, Inverse Laplace transform, Laplace transform of periodic function and unit
step function, Convolution theorem, Application of Laplace transform to solve linear and
simultaneous differential equation.
8
Unit-III
Fourier series Introduction of Fourier series, Periodic function and Trigonometric function with their
Fourier series expansion, Euler’s formula, Even and odd functions, Function with arbitrary
time periods, Change of interval, half range sine and cosine series.
8
Unit-IV
Partial differential equation Introduction of partial differential equation, Order and degree, Formulation of partial
differential equation, Lagrange’s method of multipliers, Linear partial differential equation
of nth order with constant coefficients, Classification of second order partial differential
equation.
8
Unit-V
Application of Partial differential equations Method of Separations of variables for solving partial differential equation. One and two
dimensional wave equation, One dimensional and two dimensional heat flow equation,
Laplace equation with suitable examples.
8
Total Lectures 40
References:
1. A Text book of Engineering Mathematics (Vol.2) by Peter V. O’ Neil, Cengage Learning.
2. B. S. Grewal: Higher Engineering Mathematics, Khanna Publications.
3. C. Prasad, Advanced Mathematics for Engineers, Prasad Mudralaya.
4. E. Kreyszij: Advanced Engineering Mathematics, Wiley Eastern.
5. M.D. Raisinghania: Ordinary & Partial Differential Equations, S. Chand Publication.
L 3 T 1 P 0
Theory 03 Practical 00 Sessional 02
