Using StarWind with MS Cluster on Windows Server 2008
-
Upload
constantin-videnski -
Category
Documents
-
view
129 -
download
1
description
Transcript of Using StarWind with MS Cluster on Windows Server 2008
![Page 1: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/1.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
StarWind iSCSI SAN Software: Using StarWindwith MS Cluster on Windows Server 2008
www.starwindsoftware.com
![Page 2: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/2.jpg)
StarWind SoftwareTechnical Reference Series
COPYRIGHT
Copyright © StarWind Software 2008-2009. All rights reserved. No part of thispublication may be reproduced, stored in a retrieval system, or transmitted in anyform or by any means, electronic, mechanical, photocopying, recording or otherwise,without the prior written consent of StarWind Software.
TRADEMARKS
“StarWind”, “StarWind Software” and the StarWind and the StarWind Software logosare trademarks of StarWind Software which may be registered in some jurisdictions.All other trademarks are owned by their respective owners.
CHANGES
The material in this document is for information only and is subject to change withoutnotice. While reasonable efforts have been made in the preparation of this documentto assure its accuracy, StarWind Software assumes no liability resulting from errors oromissions in this document, or from the use of the information contained herein.StarWind Software reserves the right to make changes in the product design withoutreservation and without notification to its users.
TECHNICAL SUPPORT AND SERVICES
If you have questions about installing or using this software, check this and otherdocuments first - you will find answers to most of your questions here or there. If youneed further assistance, please contact us.
![Page 3: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/3.jpg)
StarWind SoftwareTechnical Reference Series
3
Copyright © StarWind Software 2008-2009. All rights reserved.
Table of Contents
....................................................................................................... 4Introduction
....................................................................................................... 6Configuring Domain Controller................................................................................................................ 6Network Adapter ................................................................................................................ 7Active Directory
................................................................................................................ 19DNS
................................................................................................................ 32User Accounts ....................................................................................................... 42Configuring StarWind Server
................................................................................................................ 42Network Adapter
................................................................................................................ 43Preparing Quorum Volume
................................................................................................................ 51Preparing Generic Volume ....................................................................................................... 59Preparing Cluster Nodes
................................................................................................................ 59Node 1
................................................................................................................ 96Node 2 ....................................................................................................... 122Configuring Microsoft Cluster Service
................................................................................................................ 122Validate a Configuration
................................................................................................................ 129Create a Cluster ....................................................................................................... 136Adding New Shared Disk Resource
................................................................................................................ 136StarWind Target
................................................................................................................ 143Node 1
................................................................................................................ 155Node 2 ....................................................................................................... 165Conclusion
![Page 4: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/4.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
4
Guide
Introduction
Software clustering technology enables you to make several servers to workas a unit. Various cluster configurations can be implemented. One of the mostfrequently used configurations is the failover cluster. This configurationassumes that if one of the cluster nodes fails, the reserved node automaticallybrings online, serving the applications. With that the workflow remainsuninterrupted and secured.
Failover cluster configuration includes two (or more) server nodes that sharean external storage. Based on the iSCSI technology, StarWind Softwafe Inc.StarWind enables to create an external storage in Windows environmentwithout implementation of expensive FC or external SCSI solutions. WithStarWind you can create a shared disk array on a host running MicrosoftWindows.
![Page 5: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/5.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
5
This document gives you detailed step-by-step instructions on StarWindconfiguring for failover clusters.
Figure 1. StarWind provides shared-disk resources to clusters
![Page 6: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/6.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
6
Configuring Domain Controller
Network Adapter
The network adapter must be assigned a static IP address. Select the Use thefollowing IP address option and type in the IP address you wish to use. TheSubnet mask must also be provided. Both values must be correctly chosengiven the networking configuration of the Corporate LAN. As AD requiresDNS, an address must be provided – in this case we can specify 127.0.0.1(loopback interface address). DNS will be installed later with the other ADcomponents.
Press the OK button.
![Page 7: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/7.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
7
Active Directory
Select Start->Run and type in dcpromo.
Press the OK button to continue.
![Page 8: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/8.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
8
The Active Directory Domain Services Installation Wizard appears.
Press the Next button to continue.
![Page 9: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/9.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
9
In the wizard that appears please read the introducing instructions.
Press the Next button to continue.
![Page 10: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/10.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
10
As we are creating a new domain, select Create a new domain in a new forest.
Press the Next button to continue.
![Page 11: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/11.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
11
Specify the full DNS name of the domain to create.
Press the Next button to continue.
![Page 12: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/12.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
12
Select the forest functional level. In this example, we are going to use onlyWindows Server 2008 machines so select Windows Server 2008 functionallevel.
Press the Next button to continue.
![Page 13: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/13.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
13
Select additional options.
Press the Next button to continue.
![Page 14: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/14.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
14
A DNS warning dialog appears.
Press the Yes button to continue.
![Page 15: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/15.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
15
Customize the directories where the AD database, log files and SYSVOL datawill be stored or leave the values at their defaults.
Press the Next button to continue.
![Page 16: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/16.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
16
Type in the Directory Services Restore Mode Administrator Password.
Press the Next button to continue.
![Page 17: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/17.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
17
Check that all of the parameters are correct. Press the Back button should anychange be required.
Press the Next button to continue.
![Page 18: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/18.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
18
If successful, the wizard should look like the example image provided below.
Press the Finish button to close the wizard.
Press the Restart Now button to restart the computer.
![Page 19: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/19.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
19
DNS
Log on to the Domain controller using an account with administrativeprivileges. Launch the DNS Manager and configure the Reverse Lookup Zone.
Press the right mouse button over the Reverse Lookup Zone node and selectNew Zone... popup menu item.
![Page 20: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/20.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
20
New Zone Wizard appears.
Press the Next button to continue.
![Page 21: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/21.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
21
On the Zone Type page, select Primary Zone option and check the Store thezone in the Active Directory checkbox.
Press the Next button to continue.
![Page 22: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/22.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
22
Specify the replication scope or accept the default option.
Press the Next button to continue.
![Page 23: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/23.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
23
Choose IPv4 Reverse Lookup Zone
Press the Next button to continue.
![Page 24: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/24.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
24
Type in the Network ID to identify the reverse lookup zone.
Press the Next button to continue.
![Page 25: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/25.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
25
Specify dynamic update options.
Press the Next button to continue.
![Page 26: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/26.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
26
Check that all of the parameters are correct. Press the Back button should anychange be required.
Press the Finish button.
![Page 27: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/27.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
27
Press the right mouse button over rds.local forward lookup zone and selectNew Host (A or AAAA)... pop-up menu item.
![Page 28: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/28.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
28
New Host dialog appears. Type in the hostname of the Cluster Node 1 Serverand its IP address. Also please check the Create associated pointer (PTR)record checkbox.
Press the Add Host button to add node1 DNS record.
![Page 29: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/29.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
29
Type in the hostname of the Cluster Node 2 Server and its IP address. Alsoplease check the Create associated pointer (PTR) record checkbox.
Press the Add Host button to add node2 DNS record.
![Page 30: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/30.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
30
If successful, the DNS Manager console should look like the example imagesprovided below.
![Page 31: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/31.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
31
![Page 32: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/32.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
32
User Accounts
Administrator accounts must now be created to manage first and the secondcluster node servers. Launch the Active Directory Users and Computersmanagement console.
Press the right mouse button over the Users node. Select New->User.
![Page 33: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/33.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
33
In the dialog that appears, enter the required fields as shown in the exampleimage.
Press the Next button to continue.
![Page 34: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/34.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
34
Enter the password and optionally set the additional options.
Press the Next button to continue.
![Page 35: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/35.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
35
Check that all of the parameters are correct. Press the Back button should anychange be required.
Press the Finish button to create new user.
![Page 36: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/36.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
36
Once again press the right mouse button over the Users node.
Select New->User.
![Page 37: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/37.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
37
In the dialog that appears, enter the required fields as shown in the exampleimage.
Press the Next button to continue.
![Page 38: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/38.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
38
Enter the password and optionally set the additional options.
Press the Next button to continue.
![Page 39: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/39.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
39
Check that all of the parameters are correct. Press the Back button should anychange be required.
Press the Finish button to create new user.
![Page 40: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/40.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
40
The two users, node1adm and node2adm, must be made members of boththe Administrators and Domain Admins groups. Select both of the accountsand press the right mouse button over the selection as shown in the exampleimage.
Select Add to a group option.
![Page 41: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/41.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
41
Select Groups dialog appears. Enter the names of the groups.
Press the OK button.
![Page 42: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/42.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
42
Configuring StarWind Server
Network Adapter
The network adapter must be assigned a static IP address. Select the Use thefollowing IP address option and type in the IP address you wish to use. TheSubnet mask must also be provided. Both values must be correctly chosengiven the networking configuration of the dedicate iSCSI network that thecluster will be a part of. This interface is used for iSCSI target storagecommunications and a default gateway need not be specified.
Press the OK button.
![Page 43: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/43.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
43
Preparing Quorum Volume
Launch the StarWind Management Console selecting Start -> All Programs ->StarWind Software -> StarWind -> StarWind. After the console is launched itsicon appears in the system tray. Double click the icon with the left mousebutton or single click it with the right and select Start Management pop-upmenu item.From the StarWind Servers tree please select the computer you wish toconnect to. Press the right mouse button over the desired host (computer)and select the Connect menu item. You will be prompted to enter the login andpassword. Default ones are: root, starwind. You can always change them later. After you have successfully connected to the StarWind Service, please clickthe right mouse button over the desired host (computer) and select AddTarget pop-up menu item.In the wizard that appears, select a target name. The name must be a uniquename by which the device will be declared to the iSCSI initiators connecting toStarWind over an IP network.
![Page 44: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/44.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
44
Press the Next button to continue.
![Page 45: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/45.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
45
Select Image File device.
Press the Next button to continue.
![Page 46: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/46.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
46
Select Create new virtual disk to create a new virtual hard disk or Mountexisting virtual disk to mount an existing virtual disk that you’ve preparedbefore.
Press the Next button to continue.
![Page 47: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/47.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
47
If you have decided to create a new virtual disk please specify the location andthe name of the virtual disk you wish to be created. Also you have to providethe virtual disk size in megabytes. Check any additional parameters of thevirtual disk you wish to create. Please refer to the online help for detailsregarding those additional parameters (Compressed and Encrypted).
Press the Next button to continue.
![Page 48: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/48.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
48
Image File device has some extra parameters. Check Allow multipleconcurrent iSCSI connections (clustering) checkbox. Please refer to the onlinehelp for details regarding those additional parameters (Asynchronous mode,Allow multiple connections (clustering), Read-only mode and Specifyadvanced options).
Press the Next button to continue.
![Page 49: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/49.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
49
Check the device parameters are correct. Press the Back button should anychanges be required.
Press the Next button to continue.
![Page 50: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/50.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
50
A summary of the created device is displayed on the last wizard page (seeimage below).
Press the Finish button to close the wizard.
![Page 51: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/51.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
51
Preparing Generic Volume
Click the right mouse button over the host and select Add Target pop-up menuitem.In the wizard that appears, select a target name. The name must be a uniquename by which the device will be declared to the iSCSI initiators connecting toStarWind over an IP network.
Press the Next button to continue.
![Page 52: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/52.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
52
Select Image File device.
Press the Next button to continue.
![Page 53: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/53.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
53
Select Create new virtual disk to create a new virtual hard disk or Mountexisting virtual disk to mount an existing virtual disk that you’ve preparedbefore.
Press the Next button to continue.
![Page 54: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/54.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
54
If you have decided to create a new virtual disk please specify the location andthe name of the virtual disk you wish to be created. Also you have to providethe virtual disk size in megabytes. Check any additional parameters of thevirtual disk you wish to create. Please refer to the online help for detailsregarding those additional parameters (Compressed and Encrypted).
Press the Next button to continue.
![Page 55: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/55.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
55
Image File device has some extra parameters. Check Allow multipleconcurrent iSCSI connections (clustering) checkbox. Please refer to the onlinehelp for details regarding those additional parameters (Asynchronous mode,Allow multiple connections (clustering), Read-only mode and Specifyadvanced options).
Press the Next button to continue.
![Page 56: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/56.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
56
Check the device parameters are correct. Press the Back button should anychanges be required.
Press the Next button to continue.
![Page 57: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/57.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
57
A summary of the created device is displayed on the last wizard page (seeimage below).
Press the Finish button to close the wizard.
![Page 58: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/58.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
58
If successful, the StarWind Console should look like the sample imageprovided below.
![Page 59: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/59.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
59
Preparing Cluster Nodes
Node 1
Configuring network interfaces
Each adapter will be assigned a static IP address. Select the Use the followingIP address option and type in the IP address you wish to use. The Subnet maskand DNS server address must also be provided. All the values must becorrectly chosen given the networking configuration of the Corporate LAN thatthe cluster will be a part of. As this interface is for the public network, a defaultgateway will need to be assigned.
Press the OK button.
![Page 60: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/60.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
60
Just as was done for the first network adapter, assign appropriate values tothe TCP/IP configuration of the second network adapter using the followingexample image as guidance. This interface is used for iSCSI target storagecommunications and a default gateway need not be specified.
Press the OK button.
![Page 61: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/61.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
61
Joining the domain
Launch System Properties tool selecting Control Panel -> System.
Click the Change settings item.
![Page 62: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/62.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
62
Select Computer Name tab.
Press the Change… button.
![Page 63: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/63.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
63
In the Computer Name Changes dialog enter domain to join.
Press the OK button.
![Page 64: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/64.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
64
Enter the name and password of an account with permission to join to thedomain (node1adm).
Press the OK button to join.
![Page 65: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/65.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
65
If successful, the notification dialog like the one on the image shown belowshould appear.
Press the OK button.
![Page 66: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/66.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
66
You must restart the computer for the changes to take effect.
Restart the server. Log in as node1adm and install MS iSCSI Initator.
![Page 67: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/67.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
67
Configuring iSCSI initiator
Launch the Microsoft iSCSI Software Initiator application Administrative Tools-> iSCSI Initiator
Select the Discovery Tab.
![Page 68: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/68.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
68
In the Target Portals group, click the Add Portal... button.
Press the Add Portal... button.
![Page 69: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/69.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
69
In the Add Target Portal dialog enter IP address or DNS name of the StarWindtarget server.
Press the OK button to continue.
![Page 70: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/70.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
70
Click on the Targets tab. Select the IQN of the target just added.
Press the Log On… button.
![Page 71: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/71.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
71
The Log On to Target dialog now appears. In this dialog click on the checkboxAutomatically restore this connection when the system boots to make thisconnection persistent.
Press the OK button to continue.
Press the OK button to continue.
![Page 72: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/72.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
72
If successful, the initiator is now logged on to StarWind.
![Page 73: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/73.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
73
Initializing, formatting and creating partitions
When the StarWind Disks are connected, they show up on the initiatormachine as new disk devices. Before these devices can be used as clusterdisks, they have to be initialized and formatted. Launch the ComputerManagement console.
Select Disk Management.
![Page 74: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/74.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
74
Bring disks online. Press the right mouse button over the disk and selectOnline.
![Page 75: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/75.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
75
![Page 76: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/76.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
76
Initialize the Disks. Press the right mouse button over the Disk and selectInitialize Disk. Follow the wizard to initialize the new disks.
![Page 77: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/77.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
77
Press the OK button to continue.
![Page 78: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/78.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
78
Both disks have now been initialized.
![Page 79: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/79.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
79
Right-click over the unallocated space and select New Simple Volume. Followthe instructions in the wizard to create an NTFS partition for use as thequorum disk.
![Page 80: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/80.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
80
New Simple Volume Wizard appears.
Press the Next button to continue.
![Page 81: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/81.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
81
Specify new volume size in megabytes.
Press the Next button to continue.
![Page 82: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/82.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
82
Choose the Drive Letter to assign.
Press the Next button to continue.
![Page 83: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/83.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
83
Specify format options. Provide the Volume Label.
Press the Next button to continue.
![Page 84: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/84.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
84
Check the settings are correct. Press the Back button should any changes berequired.
Press the Finish button to close the wizard.
![Page 85: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/85.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
85
If successful, a new volume will be created as shown in the example imagebelow. Repeat the same steps to create the second volume.
Right-click over the unallocated space and select New Simple Volume. Followthe instructions in the wizard to create an NTFS partition for use as the genericdisk.
![Page 86: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/86.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
86
New Partition Wizard appears.
Press the Next button to continue.
![Page 87: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/87.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
87
Specify new volume size in megabytes.
Press the Next button to continue.
![Page 88: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/88.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
88
Choose the Drive Letter to assign.
Press the Next button to continue.
![Page 89: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/89.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
89
Specify format options. Provide the Volume Label.
Press the Next button to continue.
![Page 90: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/90.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
90
Check the settings are correct. Press the Back button should any changes berequired.
Press the Finish button to close the wizard.
![Page 91: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/91.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
91
If successful, both of the disks are now formatted as shown in the exampleimage below.
![Page 92: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/92.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
92
Installing Failover Clustering Feature
Launch the Computer Management console. Select Features node from thelist.
Click the Add Features to continue.
![Page 93: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/93.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
93
Add Features Wizard appears. Check the Failover Clustering feature.
Press the Next button to continue.
![Page 94: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/94.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
94
Check that the parameters are correct. Press the Previous button should anychanges be required.
Complete the installation of the Failover Clustering Feature by pressing theInstall button.
![Page 95: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/95.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
95
If the feature is successfully installed, the wizard should look similar to theexample image below.
Press the Close button.
Shut down the server.
![Page 96: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/96.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
96
Node 2
Configuring network interfaces
Each adapter will be assigned a static IP address. Select the Use the followingIP address option and type in the IP address you wish to use. The Subnet maskand DNS server address must also be provided. All the values must becorrectly chosen given the networking configuration of the Corporate LAN thatthe cluster will be a part of. As this interface is for the public network, a defaultgateway will need to be assigned.
Press the OK button.
![Page 97: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/97.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
97
Just as was done for the first network adapter, assign appropriate values tothe TCP/IP configuration of the second network adapter using the followingexample image as guidance. This interface is used for iSCSI target storagecommunications and a default gateway need not be specified.
Press the OK button.
![Page 98: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/98.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
98
Joining the domain
Launch System Properties tool selecting Control Panel -> System.
Click the Change settings item.
![Page 99: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/99.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
99
Select Computer Name tab.
Press the Change… button.
![Page 100: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/100.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
100
In the Computer Name Changes dialog enter domain to join.
Press the OK button.
![Page 101: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/101.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
101
Enter the name and password of an account with permission to join to thedomain (node2adm).
Press the OK button to join.
![Page 102: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/102.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
102
If successful, the notification dialog like the one on the image shown belowshould appear.
Press the OK button.
![Page 103: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/103.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
103
You must restart the computer for the changes to take effect.
Restart the server. Log in as node2adm and install MS iSCSI Initator.
![Page 104: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/104.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
104
Configuring iSCSI initiator
Launch the Microsoft iSCSI Software Initiator application Administrative Tools-> iSCSI Initiator
Select the Discovery Tab.
![Page 105: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/105.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
105
In the Target Portals group, click the Add Portal... button.
Press the Add Portal... button.
![Page 106: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/106.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
106
In the Add Target Portal dialog enter IP address or DNS name of the StarWindtarget server.
Press the OK button to continue.
![Page 107: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/107.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
107
Click on the Targets tab. Select the IQN of the target just added.
Press the Log On… button.
![Page 108: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/108.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
108
The Log On to Target dialog now appears. In this dialog click on the checkboxAutomatically restore this connection when the system boots to make thisconnection persistent.
Press the OK button to continue.
Press the OK button to continue.
![Page 109: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/109.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
109
If successful, the initiator is now logged on to StarWind.
![Page 110: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/110.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
110
Assigning drive letters
When the StarWind Disks are connected, they show up on the initiatormachine as new disk devices. Before these devices can be used as clusterdisks, they have to be mounted. Launch the Computer Management console.
Select Disk Management.
![Page 111: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/111.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
111
Bring disks online. Press the right mouse button over the disk and selectOnline.
![Page 112: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/112.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
112
![Page 113: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/113.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
113
The picture below shows that Windows has automatically assigned DriveLetters to the mounted volumes. As these are local drive letters they may notbe the same as we have assigned to these volumes on the first node. However,as all volumes of a cluster must be assigned the same drive letters, anydifferences must be manually changed. Press the right mouse button over theQuorum volume.
Select Change Drive Letter and Paths...
![Page 114: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/114.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
114
Change the Drive Latter for the Quorum to Q.
![Page 115: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/115.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
115
Press the right mouse button over the Generic volume.
Select Change Drive Letter and Paths...
![Page 116: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/116.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
116
Change the Drive Latter for the Generic to R.
![Page 117: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/117.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
117
If successful, the Computer Management console should look like the sampleimage provided below.
![Page 118: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/118.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
118
Installing Failover Clustering Feature
Launch the Computer Management console. Select Features node from thelist.
Click the Add Features to continue.
![Page 119: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/119.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
119
Add Features Wizard appears. Check the Failover Clustering feature.
Press the Next button to continue.
![Page 120: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/120.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
120
Check that the parameters are correct. Press the Previous button should anychanges be required.
Complete the installation of the Failover Clustering Feature by pressing theInstall button.
![Page 121: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/121.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
121
If the feature is successfully installed, the wizard should look similar to theexample image below.
Press the Close button.
Shut down the server.
![Page 122: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/122.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
122
Configuring Microsoft Cluster Service
Validate a Configuration
Start both Cluster Node 1 Server and Cluster Node 2 Server. Launch theFailover Cluster Management console selecting Administrative Tools->Failover Cluster Management.
After the management console is launched please click Validate aConfiguration... item to ensure that the configuration is suitable for failoverclustering.
![Page 123: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/123.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
123
Validate a Configuration Wizard appears.
Press the Next button to continue.
![Page 124: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/124.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
124
Add the names of servers you wish to use as cluster nodes.
Press the Next button to continue.
![Page 125: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/125.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
125
Select Run all tests (recommended) for testing the complete configuration.
Press the Next button to continue.
![Page 126: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/126.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
126
Check the parameters are correct. Press the Previous button should anychanges be required.
Press the Next button to continue.
![Page 127: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/127.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
127
If all of the tests are successful, the wizard should look similar to the exampleimage below.
![Page 128: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/128.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
128
If successful, the wizard should look like the example picture provided below.
Press the Finish button.
![Page 129: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/129.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
129
Create a Cluster
It is now time to create the cluster. Click Create a Cluster item from theActions panel shown on the right.
![Page 130: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/130.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
130
Create a Cluster Wizard appears.
Press the Next button to continue.
![Page 131: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/131.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
131
Add the names of servers you wish to use as cluster nodes.
Press the Next button to continue.
![Page 132: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/132.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
132
Specify Cluster Name and Cluster IP address.
Press the Next button to continue.
![Page 133: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/133.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
133
Check the parameters are correct. Press the Previous button should anychanges be required.
Press the Next button to continue.
![Page 134: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/134.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
134
If successful, the wizard should look like the example picture provided below.
Press the Finish button.
![Page 135: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/135.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
135
Now that the creation of the cluster is complete it will be shown in the panel onthe left.Expand the cluster by clicking on the ‘+’ symbol next to the cluster, then clickon Storage. The Failover Cluster Management console should look like theexample picture provided below. Both cluster disk resources will be shown asonline.
![Page 136: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/136.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
136
Adding New Shared Disk Resource
StarWind Target
Click the right mouse button over the host and select Add Target pop-up menuitem.In the wizard that appears, select a target name. The name must be a uniquename by which the device will be declared to the iSCSI initiators connecting toStarWind over an IP network.
Press the Next button to continue.
![Page 137: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/137.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
137
Select Image File device.
Press the Next button to continue.
![Page 138: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/138.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
138
Select Create new virtual disk to create a new virtual hard disk or Mountexisting virtual disk to mount an existing virtual disk that you’ve preparedbefore.
Press the Next button to continue.
![Page 139: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/139.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
139
If you have decided to create a new virtual disk please specify the location andthe name of the virtual disk you wish to be created. Also you have to providethe virtual disk size in megabytes. Check any additional parameters of thevirtual dsik you wish to create. Please refer to the online help for detailsregarding those additional parameters (Compressed and Encrypted).
Press the Next button to continue.
![Page 140: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/140.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
140
Image File device has some extra parameters. Check Allow multipleconcurrent iSCSI connections (clustering) checkbox. Please refer to the onlinehelp for details regarding those additional parameters (Asynchronous mode,Allow multiple connections (clustering), Read-only mode and Specifyadvanced options).
Press the Next button to continue.
![Page 141: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/141.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
141
Check the device parameters are correct. Press the Back button should anychanges be required.
Press the Next button to continue.
![Page 142: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/142.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
142
A summary of the created device is displayed on the last wizard page (seeimage below).
Press the Finish button to close the wizard.
![Page 143: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/143.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
143
Node 1
Launch the Microsoft iSCSI Software Initiator application Administrative Tools-> iSCSI Initiator. Click on the Targets tab. Select the IQN of the target justadded.
Press the Log On… button.
![Page 144: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/144.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
144
The Log On to Target dialog now appears. In this dialog click on the checkboxAutomatically restore this connection when the system boots to make thisconnection persistent.
Press the OK button to continue.
![Page 145: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/145.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
145
When the StarWind Disks are connected, they show up on the initiatormachine as new disk devices. Before these devices can be used as clusterdisks, they have to be initialized and formatted. Launch the ComputerManagement console. Select Disk Management.
Bring disk online. Press the right mouse button over the disk and select Online.
![Page 146: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/146.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
146
Initialize the Disk. Press the right mouse button over the Disk and selectInitialize Disk. Follow the wizard to initialize the new disk.
![Page 147: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/147.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
147
Press the OK button to continue.
![Page 148: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/148.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
148
The disk has now been initialized. Right-click over the unallocated space andselect New Simple Volume. Follow the instructions in the wizard to create anNTFS partition for use as the spool disk.
![Page 149: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/149.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
149
New Simple Volume Wizard appears.
Press the Next button to continue.
![Page 150: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/150.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
150
Specify new volume size in megabytes.
Press the Next button to continue.
![Page 151: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/151.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
151
Choose the Drive Letter to assign.
Press the Next button to continue.
![Page 152: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/152.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
152
Specify format options. Provide the Volume Label.
Press the Next button to continue.
![Page 153: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/153.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
153
Check the settings are correct. Press the Back button should any changes berequired.
Press the Finish button to close the wizard.
![Page 154: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/154.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
154
If successful, the disk is now formatted as shown in the example image below.
Shut down the node.
![Page 155: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/155.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
155
Node 2
Launch the Microsoft iSCSI Software Initiator application Administrative Tools-> iSCSI Initiator. Click on the Targets tab. Select the IQN of the target justadded.
Press the Log On… button.
![Page 156: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/156.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
156
The Log On to Target dialog now appears. In this dialog click on the checkboxAutomatically restore this connection when the system boots to make thisconnection persistent.
Press the OK button to continue.
![Page 157: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/157.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
157
When the StarWind Disks are connected, they show up on the initiatormachine as new disk devices. Before these devices can be used as clusterdisks, they have to be mounted. Launch the Computer Management console.Select Disk Management.
Bring disks online. Press the right mouse button over the disk and selectOnline.
![Page 158: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/158.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
158
The picture below shows that Windows has automatically assigned DriveLetters to the mounted volumes. As these are local drive letters they may notbe the same as we have assigned to these volumes on the first node. However,as all volumes of a cluster must be assigned the same drive letters, anydifferences must be manually changed. Press the right mouse button over theSpool volume.
Select Change Drive Letter and Paths...
![Page 159: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/159.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
159
Change the Drive Latter for the Spool to S.
![Page 160: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/160.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
160
If successful, the Computer Management console should look like the sampleimage provided below.
![Page 161: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/161.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
161
Launch the Failover Cluster Management console. Click on Storage node.
Click Add a Disk item from the Actions panel shown on the right.
![Page 162: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/162.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
162
Add Disks to a Cluster dialog appears. Select the disk to add.
Press the OK button to continue.
![Page 163: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/163.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
163
When completed, the disk is now a cluster disk.
![Page 164: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/164.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
164
Start the other servers in the cluster.
![Page 165: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/165.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
165
Conclusion
![Page 166: Using StarWind with MS Cluster on Windows Server 2008](https://reader031.fdocuments.net/reader031/viewer/2022013121/546a4ac9b4af9f373c8b4867/html5/thumbnails/166.jpg)
StarWind SoftwareTechnical Reference Series
Copyright © StarWind Software 2008-2009. All rights reserved.
Contacts
StarWind Software Inc.
40 Mall Rd., Burlington
MA 01803, USA
www.starwindsoftware.com
Support:
Support Forum:
Sales E-mail:
US Headquarters
Phone:
www.starwindsoftware.com/support
www.starwindsoftware.com/forums
617-449-7717
Fax: 617-505-5845
EMEA: 1-888-532-2203