30 Watt Motion Activated Security LightWIFI-CON

User ManualPart Number:

Important: Read all instructions prior to installation. MASL-NW30-TBR

Installation

Adjusting Sensor

Manual Override

Features

Required Tools

Specifications

1 - Phillips Screwdriver1 - Flathead Screw Driver1 - Tube Silicone Caulk

• Three 10 Watt Light Heads• Motion and Light Sensor• High heat conduction aluminum alloy shell with optimal heat

dissipation• Anti-corrosion and a weatherproof design

4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com

Operating Voltage 90~135 VACRated Wattage 30 Watts

Intensity 2400 lumenColor Temperature 4000 K

Beam Angle 100 degree / light headCRI 84

LED Type COBLED Count and Watts 3 LEDs x 10 Watts

IP Rating Weatherproof IP65Operating Temperature Range -40~122° F (-40~50° C)

Warranty 5 Years

1. Begin by turning off power to the circuit from the electrical panel.

2. Remove existing fixture if retrofitting.3. Install Crossbar to J-Box using screws provided with J-Box

and tighten.4. Insert wiring from light through center hole in Foam Gasket.5. Connect the yellow/green (ground) wire from light to

grounding screw inside J-Box. Connect the white (neutral) wire from the supply cable to the white wire of light and secure with a wire nut. Connect the black (line) wire from the supply cable to the black wire of light and secure with a wire nut.

6. Insert wiring into J-Box in a manner that allows a clear path for the Mounting Screw to pass unobstructed to Crossbar.

7. Align Foam Gasket and Light to J-Box and Crossbar, removing the appropriate knockouts on Foam Gasket. Be sure to mount the Light so the Motion Sensor is at the bottom.

8. Apply light coat of silicone caulk to outer edge of Foam Gasket sealing the Light to J-Box. Leave a slight gap in the silicone at the bottom of the mounting flange.

9. While keeping the Foam Gasket and Light aligned to J-Box, insert and tighten Mounting Screw.

10. Install Mounting Screw Cover by pressing onto head of Mounting Screw.

11. Restore power to the circuit from the electrical panel.12. Loosen adjustment knobs and aim Light Heads to desired

position then tighten adjustment knobs. Glare shields may also be rotated for blocking undesired light output.

1. Set ON-TIME switch to TEST position.2. Rotate RANGE knob clockwise to the MAX(maximum) position.3. Aim the Motion Sensor at least 10 degrees downward and across the

desired detection area.4. Test Motion Sensor by walking around desired detection area. Light will

turn on for approximately 40 seconds and then turn off if no additional motion is detected within 8 seconds. Red LED on Motion Sensor will turn on then off when motion is detected.

5. Aim sensor and adjust RANGE until desired detection area is covered.6. Change ON-TIME switch to the desired setting (1/5/10 minutes)

Turn the wall switch off and back on within 3 seconds to disable the Motion Sensor and allow the light to run continuously all night. Light will automatically turn off at dawn and reset to motion detection for the next dusk cycle.

PLEASE READ THESE INSTRUCTIONS CAREFULLY

AND SAVE THEM, YOU MAY NEED THEM AT A LATER

NSTALLING YOUR MOTION ACTIVATED

LIGHT, YOU ARE READY TO SET/AIM THE MOTION

SENSOR. MAKE SURE THE WALL SWITHCH IS IN THE

Switch the TIMES/TEST switch in the TEST position to

disable the photocell and allow light to come on during daylight

Rotate the RANGE knob fully clockwise to maximum

Setting the Motion Sensor

Photocell

Detection Range Adjustment Knob

On-Time Adjustment Switch

CrossbarScrews

White Wire Supply

Rubber Washer

MountingScrewCover

Green or Bare Ground Wire

Black Wire Supply

Junction BoxMount Base

Center Screw Hole

Wire Nut

GasketCrossbar

Mounting Screw