User Manual for Sekure Standard Application
18
User Manual for Sekure Standard Application Steps to run the Application: 1. Double Click the SekureStdApp.exe. 2. The Application Shows the Initializing Window as shown in Figure 1 and it shows the Sekure is initializing on which COM Port. You can change the COM port by manually from the SekureCom.txt file in the root directory of the application or from the application. Figure: 1 This COM port can be Configure from the Application by pressing the Tricubes icon in the title bar as shown in Figure 2.
Transcript of User Manual for Sekure Standard Application
User Manual for Sekure Standard Application
Steps to run the Application:
1. Double Click the SekureStdApp.exe.
2. The Application Shows the Initializing Window as shown in Figure 1 and it
shows the Sekure is initializing on which COM Port. You can change the COM
port by manually from the SekureCom.txt file in the root directory of the
application or from the application.
Figure: 1
This COM port can be Configure from the Application by pressing the Tricubes icon
in the title bar as shown in Figure 2.
Figure: 2
If you click the Sekure App Settings menu it will results in Figure 3. From that we
can choose the Sekure initialization port number and the Sekure Version.
Once you selected the port number and the Sekure version press the OK button in the
dialog. If you want it to be the same press Cancel button. To apply the changes you
need to close the application and run it again.
Figure: 3
3. After the device initialized then the Application automatically switches to Insert
Card Window as in Figure 4.
Figure: 4
4. After you insert the card in to the device the Application will check whether it is a
valid card or not. If it is valid then it starts reading the Card or it will show a
message corrupted or invalid card as shown in Figure 5.
Figure: 5
5. While the Application reading the identity info it shows a message “Reading
Identity card Info” as shown in Figure 6.
Figure: 6
6. Once the Application finish reading Identity Info, it will automatically switch to
Identity Card Tab and display the data and continue reading the photo and shows
message “Reading photo”. It also shows how many percent it finish reading the
card. By the time the application shows Figure 7.
Figure: 7
After it finish reading the photo it displays the photo and continues reading the
data of the next tab one after another as shown in Figure 8.
Figure: 8
7. After it displays the photo it continues reading data of driving license information
from the card and it shows a message “Reading Driving Info”. If the application
finish reading driving license info it continues reading Passport info and show the
message “Reading Passport” as in Figure 9. At that time you can switch to
Driving License tab but not to the Passport tab. When you press the driving
license tab button the application will show the Figure 10
Specimen
Figure: 9
Specimen
Figure: 10
8. After the application finishes reading the Passport information we can switch to
Passport tab. If you press the Passport tab button the application switch to
passport tab and show a window as shown in Figure 11.
Figure: 11
9. After the application finishes reading the Meps information we can switch to
Meps tab. If you press the Meps tab button the application switch to Meps tab and
show a window as shown in Figure 12.
Figure: 12
10. After the application finishes reading the Biometrics information we can switch to
Biometrics tab. If you press the Biometrics tab button the application switch to
Biometrics tab and show a window as shown in Figure 13.
Figure: 13
11. Once the application finishes reading all the data from the card, the animation
controls and the progress bar will disappear.
12. Now you can verify the card holder’s finger. For that you have to press the verify
finger button depends on which finger the card holder placed on the Sensor. Once
you pressed the verify finger button application will show the status. If no finger
on the sensor it will show the status as shown in figure 14.
Figure: 14
13. Once the card holder place the finger on the sensor it will shows the finger print
image as shown in figure 15.
Figure: 15
14. If the biometric verification success the application will show information in the
result as “PASS” or else it will show “FAIL”.
15. After you verify both fingers and the result is “PASS” then you can switch to
Print tab. If you press the print tab button then it will switch to print tab and show
a window as in Figure 16.
Specimen
Figure: 16
16. If you press the preview button, it will results in a different window as shown in
figure 17.
Figure: 17
17. After you finish printing you can remove the card from the device. If you remove
the card while the application finishes reading the data from the card or while it is
reading the application switches back to Insert Card window as shown in figure 4
and you cannot switch to other tabs.
18. You also can change the company logo as shown in the following figure by
changing the image in the logo. Jpg in the root directory of the application.
Specimen
Specimen
