User ManualEnOcean

V 0.1

&

2

®®

Last update: July 2012All software-related descriptions refer to the software V1279. We recommend to update older versions of the system. Small deviations in the description because of software changes are possible.All listed brands and logos are registered trademarks of their respective owners.

Copyright

All rights reserved. Without the the prior written permission of the publisher, no part of this document for any pur-pose, be reproduced or transmitted, and regardless of any form or by any means, electronic or mechanical, this is happening.

If this publication is made available on media by Ekon GmbH, GmbH Ekon grant permission, copies of the information contained in this file is only for private use and not to download or print for redistribution. No part of this publication may be changed, modified or used for commercial purposes. Ekon is not liable for damages resulting from the use of an illegal modified or altered publication.

The devices comply with the relevant guidelines and standards of the EU.

3

3

Table of Content

1. Electrical outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2. Software activation on the myGEKKO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

4

1. Electrical outlet

The EnOcean gateway is a serial interface for integrating wireless radio transmitters. EnOcean devices can be connected to the myGEKKO by means of this interface.EnOcean radio modules are based on miniaturised energy converters, extremely power-saving elec-tronics and reliable radio technology.

Technical dataInput voltage range 12 - 30VDC or 12 – 24VAC

Current consumption max. 40 mA

Radio module TCM120

Wireless protocol EnOcean standard (PTM/STM/CTM)

Antenna integrated

Connection 8-pin plug terminals for T-wire cable 1x4x0.8mm2

Housing Plastic ABS

Dimensions 80 x 80 x 25 mm

Weight 80g

Protection class IP 20

Operating temperature -5°C ... +40°C, rel. humidity (non-condensing) 5 ... 90%

EnOcean Gateway

The EnOcean gateway (Art. nr. ACC-ENO01) is con-nected to an RS232 interface on the myGEKKO. The gateway can be connected to either a free interface directly on the myGEKKO Touch or the interface distributor USB/quadruple RS232 (Art. nr. ACC-RS201). A maximum of 5 interfaces are avail-able on a myGEKKO Touch with distributor.To connect the gateway to an RS232 interface a RS232/RS485 converter (Art. nr. ACC-RS401) is required

Connection to the myGEKKO Touch

Connection via Interface

RS485

COM 1with RS232 / RS485 converter

COM 2with RS232 / RS485 converter

USB-COM 1-4vit USB interface distributor and

RS232 / RS485 converter

5

Connection details

Baud rate The baud rate is to be set to 57600 on the EnOcean gateway, i.e. jumpers J1 and J2 are not set.

Jumper J3 is for setting the terminating resistor. This is set at the last gateway in the line.

PWR+

Terminal 1

Terminal 2

Terminal 3

Terminal 4

Terminal 5

PWR-

RX-

RX+

TRX-

TRX+

+24VDC

GND

Optional powersupply: 7-12VDC

1

2

A

B

Jumper SW1 (485-2W) must be in position ON!

Interface converter RS232/RS485 Art. ACC-RS401

PWR+

PWR-

RX-

RX+

TRX-

TRX+

+24VDC +24VDC +24VDC +24VDCGND GND GND GND

6

2. Software activation on the myGEKKOGateway configurationLog in as configurator.

In the main settings change to IO configuration .1. The EnOcean gateway can be configured to the IO stations 5-8. For this, set the station to En-2. Ocean. Select the respective port and set the baud rate to 57600.Under ‘Configuration >>’ tap a free gateway and set the desired address. (each address must be 3. used only once – avoid duplicate addresses)Now press the S4 button on the EnOcean gateway for more than 1 second to read-in the current 4. ID nr. of the gateway. You can read it out from the ‘LRN-MESSAGE-ID’ field.

If the current address of the gateway is known you can change it via Change ID. (NEW ID is the new address)

Caution! For security reasons, the addresses of the EnOcean gateways cannot be changed more than 10 times.

To test the configuration you can use the buttons LED 5 ON/OFF to switch the Led5 on and off. The connection works properly, if the LED on the gateway switches on/off. Additionally, myGEKKO re-sponds with an ‘OK’ message.

7

Read-in of radio transmittersEach radio transmitter has a unique ID. This ID has to be taught-in by the gateway or entered manu-ally in the list of participants.

Entering participants manually:Usually, an 8-digit ID can be found on the backside of the radio transmitter. This ID can be entered in the list of participants of the myGEKKO. Therefore, go to the ‘TLNR’ menu of the gateway, press ‘Edit’ and set the participant number via ‘SET’. Press EDIT again to exit the edit mode.Now the gateway can communicate with the wireless transmitter.

Teach-in of participants:Press the S3 button for more than 1 second to start the read-in mode. Now, LED3 on the gateway is red and the LRN field on the myGEKKO orange. Confirm the programming/learn button on the wire-less transmitter (press push-button at push-button) and it will be taught-in automatically on the gate-way. Now you can control the newly taught-in ID of the wireless transmitter in the participants list of the myGEKKO.

After the teach-in the programming/learning mode needs to be deactivated. For this, press the S3 button on the gateway again for 1 second.

Caution! Only one radio transmitter must send when the gateway is in programming/learning mode.If multiple transmitters send simultaneously, all of them will be read in

8

www.my-gekko.com

A first class product of Europe!The result of a close collaboration between Italy, Switzerland and Germany