User Manual Camara Vivotek ST7501

IP Survei l lance

ST7501 Free-standard

rev. 1.52

VIVOTEK - A Leading Provider of Multimedia Communication Solutions

i - User's Manual

Getting Started ........................................................................................................................................1

Introducing ST7501 ............................................................................................................................1Special Features .........................................................................................................................1

ST7501 Server and Client Components .............................................................................................2Usage Scenario ..................................................................................................................................2ST7501 Server Functionality ..............................................................................................................3ST7501 LiveClient Functionality .........................................................................................................4ST7501 Playback Functionality ..........................................................................................................5Minimum System Requirements ........................................................................................................6

ST7501 Installation ..................................................................................................................................7

Installing the ST7501 Software ..........................................................................................................7

ST7501 Server ......................................................................................................................................10

Activating the ST7501 Server ...........................................................................................................10How to Configure the Server ............................................................................................................10How to Stop/Reboot the Server ........................................................................................................10

ST7501 LiveClient Configuration ...........................................................................................................12

Activating the ST7501 LiveClient and Logging in to a ST7501 Server .............................................12ST7501 LiveClient User Interface ....................................................................................................13

Menu Bar ...................................................................................................................................13Status Panel ..............................................................................................................................13Quick Access Bar ......................................................................................................................14Live Video Monitoring Window ..................................................................................................14Device tree ................................................................................................................................15Camera Control Panel ...............................................................................................................16

Pan/Tilt/Zoom (PTZ) Control Panel ....................................................................................16Two Way Audio Control Panel ............................................................................................17Language Selection ...........................................................................................................17

Event Window ...........................................................................................................................18Instant Playback ........................................................................................................................19Audio Control ............................................................................................................................19

How to Manage Devices ..................................................................................................................20Insert Devices ...........................................................................................................................20Insert a Video Server .................................................................................................................24Update Devices .........................................................................................................................26Delete Devices from the ST7501 Server ...................................................................................27Batch Insert Devices .................................................................................................................28View Live Videos .......................................................................................................................32

Dual / Multiple Streams ......................................................................................................32Refresh ...............................................................................................................................32

Table of Contents


User's Manual - ii

Streaming Server ...............................................................................................................32Camera Settings ................................................................................................................33

Remove Live Video from the Video Monitoring Window ...........................................................33How to Change the ST7501 LiveClient Layout ................................................................................34

Changing the Layout of the Live Video Monitoring Window ......................................................34Switch Video Channels ......................................................................................................34Configure Layout Mode ......................................................................................................34Rotating Video Pages ........................................................................................................35Edit Layout .........................................................................................................................35

Maximize/Minimize the Live Video Monitoring Window .............................................................37View Live Video on Dual Monitor ..............................................................................................38

View up to 32 channels simultaneously .............................................................................39Using different layouts on each monitor .............................................................................39

View Live Video with Multiple Monitors .....................................................................................40How to Manage User Accounts ........................................................................................................41

The Default User Roles and Permissions of User Accounts .....................................................41Manage a User Account ............................................................................................................42

Add a New User Account ...................................................................................................42Permission of the User Account ................................................................................................44Delete the User Account ...........................................................................................................45

How to Set up Association Management ..........................................................................................46Association Management ..........................................................................................................46

How to Set up Event Management ...................................................................................................48Event Management ...................................................................................................................48

How to Configure the Station General Settings ................................................................................54Server Settings ..........................................................................................................................54Log Settings ..............................................................................................................................54

How to Configure Station Network Settings .....................................................................................55Port Settings ..............................................................................................................................55UPnP Settings ...........................................................................................................................55Proxy Settings ...........................................................................................................................55

How to Edit Recording Groups .........................................................................................................56Recording Storage Settings ......................................................................................................56

Defult Storage Group Settings ...........................................................................................57Add New Recording Group(s) ............................................................................................59

How to Edit Recording Schedules ....................................................................................................60Edit Schedule List .....................................................................................................................61

Add Schedules ...................................................................................................................61Rename Schedules ............................................................................................................61Delete Schedules ...............................................................................................................61


iii - User's Manual

Load/Save Schedule Templates .........................................................................................62Edit Camera List ........................................................................................................................63Edit Time Frame List .................................................................................................................64

Add New Time Frames .......................................................................................................65Recording Settings .............................................................................................................66

The Concept of Repeat Frequency ...........................................................................................67Repeat Frequency: Daily Setting .......................................................................................68Repeat Frequency: Weekly Setting (Day-based) ...............................................................71Repeat Frequency: Monthly Setting (Day-based) ..............................................................74Repeat Frequency: Yearly Setting (Day-based) .................................................................76

How to Manually Begin /Stop Recording ..........................................................................................78How to Edit Scheduled Backup Settings ..........................................................................................79

Select Backup Source ...............................................................................................................79Setup Backup Schedule ............................................................................................................80Select Backup Target ................................................................................................................80Other Options ............................................................................................................................80

How to Configure Station Server Settings ........................................................................................81DDNS Settings ..........................................................................................................................81Network Storage Settings .........................................................................................................82SMTP Settings ..........................................................................................................................83Relay Settings ...........................................................................................................................84

How to Use the Talk Panel ...............................................................................................................85Add a Camera to the Talk Panel ................................................................................................85Remove a Camera from the Talk Panel ....................................................................................87

How to Configure E-map Settings ....................................................................................................88Upload an E-map ......................................................................................................................88User Interface of E-map Settings Page (View Mode) ................................................................89

Quick Access Bar ...............................................................................................................90Status Panel .......................................................................................................................90

User Interface of E-map Settings Page (Edit Mode) .................................................................91Device Management .................................................................................................................92Live View Dialog Settings ..........................................................................................................93

Open Live View Dialog .......................................................................................................93Send to Single View ...........................................................................................................93

E-map Link ................................................................................................................................94How to Configure Client Settings .....................................................................................................97

Snapshot Settings .....................................................................................................................97Take a Snapshot ................................................................................................................98

Recording Settings ....................................................................................................................99Type 1: Record to EXE ......................................................................................................99


User's Manual - iv

Type 2: Record to 3GP .......................................................................................................99Type 3: Record to AVI ......................................................................................................100Built-in Media Player--EXE ...............................................................................................103

View Settings ...........................................................................................................................105Display Location ...............................................................................................................105Date and Time Format .....................................................................................................106Video Display Mode .........................................................................................................106Font Settings ....................................................................................................................106

General Settings .....................................................................................................................107Event Settings ..................................................................................................................107Rotation Settings ..............................................................................................................107Display Settings ...............................................................................................................107System Settings ...............................................................................................................107

Joystick Settings .....................................................................................................................108Enable Joystick ................................................................................................................108

Proxy Settings .........................................................................................................................112How to Search for a Device on the Device Tree ............................................................................ 113How to Print a Video Image ............................................................................................................ 114How to Lock ST7501 LiveClient for Security Concerns .................................................................. 114How to Log out from the ST7501 Server ........................................................................................ 115How to Exit ST7501 LiveClient ....................................................................................................... 115

ST7501 Playback Configuration ..........................................................................................................116

Activating ST7501 Playback and Logging in to a Server ............................................................... 116ST7501 Playback User Interface .................................................................................................... 117

Menu Bar .................................................................................................................................117Status Panel ............................................................................................................................117Quick Access Bar ....................................................................................................................118Recorded Video Playback Window ......................................................................................... 118Language Selection ................................................................................................................119Query Panel-- Browsing Page .................................................................................................119Query Panel--Time Search Page ............................................................................................120Query Panel--Event Search Page ...........................................................................................121Query Panel--Log Viewer Page ...............................................................................................122Video Clips List Window ..........................................................................................................123Playback Control Panel ...........................................................................................................124

How to Playback Recorded Video ..................................................................................................125Select a Recorded Video Clip .................................................................................................125Remove Recorded Video Clips from Video Cells ....................................................................127Timeline Slider Bar and Histogram ..........................................................................................127Zoom in / out of the Histogram ................................................................................................128


v - User's Manual

Audio Control ..........................................................................................................................129How to Change the Playback Layout .............................................................................................130

Changing the Layout of the Recorded Video Playback Window .............................................130Switch Video Channels ....................................................................................................130Configure Layout Mode ....................................................................................................130

Maximize/Minimize the Recorded Video Playback Window ....................................................131View Recorded Video with Multiple Monitors ..........................................................................132

How to Backup Recorded Video ....................................................................................................133How to Search for a Video Clip in a Specific Period of time ...........................................................137How to Search for Events ...............................................................................................................138

Select Event Category ............................................................................................................139Event Category- All Events ..............................................................................................139Event Category- All Motion Events...................................................................................139Event Category- All IVA events ........................................................................................140Event Category- All DI Events ..........................................................................................140Event Category- Named DI Events ..................................................................................141

Start Event Search ..................................................................................................................142Backup the Event Videos ........................................................................................................143

How to Search Logs .......................................................................................................................144Select Log Category/Log Type/Log Level ...............................................................................145

Search All Local Logs.......................................................................................................146Search Login History ........................................................................................................146Search Login Activities .....................................................................................................147

How to Configure Client Settings ...................................................................................................149Snapshot Settings ...................................................................................................................149Export Settings ........................................................................................................................149View Settings ...........................................................................................................................151Proxy Settings .........................................................................................................................151General Settings .....................................................................................................................151

System Settings ...............................................................................................................151Display Settings ...............................................................................................................151

How to Search for a Device on the Device Tree ............................................................................151How to Print a Video Image ............................................................................................................151How to Lock ST7501 Playback for Security Concerns ...................................................................152How to Log out from the ST7501 Server ........................................................................................152How to Exit ST7501 Playback ........................................................................................................152

Import and Export Utility ......................................................................................................................153

Export Utility ...................................................................................................................................153Import Utility ...................................................................................................................................153

ST7501 Service Control Tool ...............................................................................................................154


User's Manual - vi

Revision History

Rev. 1.52:1. Supports Video Server VS8801 to be attached to ST configuration.2. Supports automated saving of current layout settings.3. Added Playback as one of the user’s previleges. 4. Reflected the changes to the access to an individual camera management session from a mocked browser to the use of IE browser.


User's Manual - 1

Getting StartedIntroducing ST7501

VIVOTEK ST7501 is the new generation recording software, featuring reliable recording and easy system management for diverse IP surveillance applications. ST7501 has three major components including: ST7501 Server for recording, ST7501 LiveClient for viewing live media data and system management, and ST7501 Playback for browsing the database and retrieving the recorded media data. You can install and run the three components on a single computer, or install them on three separate computers.ST7501 Server is able to record network video streams up to 32 channels, and ST7501 LiveCli-ent allows for real-time remote monitoring. For video playback, you can use ST7501 Playback to retrieve the database with multiple advanced functions such as searching, browsing, and ex-porting. With ST7501 LiveClient and ST7501 Playback installed on other computers in different locations, you can have live viewing and database access for more efficient video management. Working seamlessly with VIVOTEK network cameras and video servers, ST7501 recording soft-ware provides you with a reliable and seamless video surveillance system.

Special Features

Convenient Remote Access via Client/Server Architecture Effective & Reliable Event Trigger Management Real-time 32-channel Live Viewing and Simultaneous 16-channel Playback Multiple Simultaneous Streams for Different Media Platforms Activity Adaptive Streaming for Dramatically Reducing Bandwidth and Storage Space Extremely Versatile Settings for Recording Storage and Recording Schedule Management Role-based User Management to Enhance Security Operations Efficient Data Backup, Search, and Export Intelligent PTZ/ E-PTZ Remote Camera Control Overall Device Management through Intuitive E-map Feature Instantly Playback Event Recording Built-in Instant Player for Playback Accessible through NAT Using the Public IP Supports Two Way Audio

* The ability to extend devices is also subject to the network bandwidth and computer performance.


2 - User's Manual

ST7501 Server and Client Components

ST7501 has three components: one server component--ST7501 Server, and two client components--ST7501 LiveClient and ST7501 Playback.

ST7501 Server provides a centralized management site for video recording. ST7501 LiveClient is a client program for the user to login to the target server over the network to modify the server's configuration, edit the server's recording storage, schedules and many other functions on the server; ST7501 Playback is another client program for the user to login and browse the recorded video database and video clips related to specific events on the server.

Usage ScenarioThe three components can be installed separately or combined together on the same host. Youcan just install the components you need on your local host. For example, you can only install ST7501 LiveClient on your local computer to monitor the live video from a remote ST7501 Server; or you can only install ST7501 Playback on another local computer to login a remote server to review recorded videos.

For user that only manages a few cameras, we recommend installing the client and server components on the same computer. A host with all of the three components installed is recognized as a stand-alone site. All the functions can be simultaneously performed on one single site.

Below we illustrate the usage scenario of ST7501 Server and client components.

Router

ST7501 LiveClient

ST7501 Server

Network Cameras

ST7501 Playback

Router

ST7501 LiveClient ST7501 Server

Network Cameras

ST7501 Playback

Stand-alone site

Remote Server Structure

Local Server Structure


User's Manual - 3

ST7501 Server Functionality

Serves as a remote video management site for all the logged in clients 32-channel video recording Store recorded data onto multiple hard/network disks Live video for the local/remote LiveClient users Recorded video for the local/remote Playback users Zero latency database recovery

To configure the server, you should use ST7501 LiveClient to log in. The convenient and intuitive user interface in ST7501 LiveClient will enable you to edit the settings of the target server.


4 - User's Manual

ST7501 LiveClient Functionality

Server function control User account management Recording storage management Recording schedule management Recorded data backup Event trigger management Flexible video live view layout Dual screens for maximum 32 channels simultaneous monitoring 1x1, 2x2, 1+5, 3x3, 1+12, 4x4, 5x5, 1+31 monitoring layouts Multiple video viewing pages Convenient evidence and data export E-map for overall management Network storage for recording Convenient switching among multiple monitors PTZ / E-PTZ operation panel for camera control Support two way audio Instant playback for event recording Support joystick control Remote configuration for network cameras


User's Manual - 5

ST7501 Playback Functionality

Browse the database of recorded video from the server Flexible video playback layout Maximum 16 channels simultaneous playback 1x1, 2x2, 1+5, 3x3, 1+12, 4x4 playback layouts Support powerful playback functions 1/8x, 1/4x, 1/2x slow-down playback 2x, 4x, 8x, 16x, 32x, 64x video playback speed Support convenient evidence and data exporting Export media files of recorded video Support Snapshot Support Print out Support convenient switching among multiple monitors Search engine Time search Event search Log search Playback while recording


6 - User's Manual

Minimum System RequirementsBefore installing the ST7501 software, please make sure your system meets the following recommended minimum system requirements.If you would like to install ST7501 Server only, please follow the requirements as below:

If you would like to install both the server and client programs, please follow the requirements as below:

Only users with Administrator privileges can install or use ST7501 on a Windows Vista system. The required hard disk space will depend on the amount of network cameras and recording group settings.

Please add more hard disks if you want to extend the system. * 32-CH, VGA, about 1 week recording: 750 GB 32-CH, 2-megapixel, about 1 week recording: 2TB x 2

ServerOperating System Windows Server 2000, 2003, 2008 / Windows XP Professional (32 and 64 bit),

Windows Vista Business (32 and 64 bit), Windows 7 (32 and 64 bit)Channels Below 32 channels

CPU Intel Core 2 Duo E64002.13GHz or above

RAM 2 GB or aboveNetwork Interface Card Ethernet, 1 Gbit recommendedGraphics Adapter AGP or PCI-Express, minimum 1024×768, 16 bit colorsHard Disk Type ATA-100, SATA, SCSI, SAS (7200 rpm or faster) in NTFS formatHard Disk Space 750 GB free *

Server, LiveClient, and Playback

Operating System Windows Server 2000, 2003, 2008 / Windows XP Professional (32 and 64 bit), Windows Vista Business (32 and 64 bit), Windows 7 (32 and 64 bit)

Channels Below 16 channels 16 ~ 32 channels

CPU Core 2 Duo E64002.13GHz or above

Core 2 Duo E86003.33GHz or above

RAM 2 GB or aboveNetwork Interface Card Ethernet, 1Gbit recommended

Graphics Adapter AGP or PCI-Express, minimum 1024×768, 16 bit colorsMinimum 128MB Video RAM, 512MB recommended

Hard Disk Type ATA-100, SATA, SCSI, SAS (7200 rpm or faster) in NTFS formatHard Disk Space 750 GB free *


User's Manual - 7

ST7501 InstallationInstalling the ST7501 Software

1. Run ST7501_Setup.exe on your computer. Click I Agree the License Agreement and specify a location to install the program.

2. Select the items you want to install, then click Next to continue. If you want to install both ST7501 Server component and Client components, please follow the steps

below to install the database.

3. Assign a username and password for the ST7501 Server and click Next to continue.

Please record the username and password for login later.

Server componentClient components


8 - User's Manual

4. Install a database on your server. There are two options--PostgreSQL (8.2 version or above) or SQL server (2005 express version or above). In order to avoid conflicts among different databases, we suggest you remove the original database from your host. Then follow the instruction below to install PostgreSQL or SQL server.

PostgreSQLPlease note that PostgreSQL may interrupt an antivirus program. Follow the steps below to install PostgreSQL Server:a. Select PostgreSQL from the drop-down list and assign a password. ST7501 server will by default store

the recorded media file under c:\Recording. Click Browse to change the path if you plan to store the data under another path. Then click Next to continue.

b. If you do not have PostgreSQL, select the first option to begin the installation. If you already have PostgreSQL installed on your host, select the second option to enter the related information.

c. Wait for the installation process to complete, then click Close to exit the installation program.


User's Manual - 9

SQL Server

Follow the steps below to install SQL Server:a. Select SQL Server from the drop-down list and assign a password. ST7501 server will by default store

the recorded media file under c:\Recording. Click Browse to change the path if you plan to store the data under another path. Then click Next to continue.

b. If you do not have SQL server, select the first option to begin the installation. If you already have SQL server installed on your host, select Windows authentification or SQL Server authentification. (Username and Password may be necessary according to the settings when you install the SQL server.) Click Install to begin the installation.

c. Wait for the installation process to complete, then click Close to exit the installation program.

Once you have created a user account for a ST7501 station, you can login to ST7501 Server from any computer over the network through LiveClient and Playback.


10 - User's Manual

ST7501 ServerActivating the ST7501 Server

ST7501 Server is a service program that will run automatically when the computer starts up.

How to Configure the Server

Please follow the steps below to configure the ST7501 Server:1. Find a local/remote computer that has installed ST7501 LiveClient.2. Activate ST7501 LiveClient and login to the target ST7501 Server.3. Configure the server using the ST7501 LiveClient user interface.

How to Stop/Reboot the Server

Please follow the steps below to stop/reboot the server:1. Under Microsoft Windows, choose "Start > Settings > Control Panel > Adminstrative Tools >

Services."2. The Service window will pop up. Search for "ST7501 Uranus Watch Dog" from the list.


User's Manual - 11

3. Right-click ST7501 Uranus Watch Dog and click Stop to stop the services of ST7501 Server.

4. Click Restart to reset ST7501 Server.

ST7501 Uranus Watch Dog


12 - User's Manual

ST7501 LiveClient ConfigurationActivating the ST7501 LiveClient and Logging in to a ST7501 Server

ST7501 LiveClient allows you to monitor live video from cameras managed by the ST7501 Server; it is also the main user interface to control many of the server functions.

After installing the ST7501 LiveClient program, please follow the steps below to activate ST7501 LiveClient:1. Run the ST7501 LiveClient program.2. A Login window will pop up. Enter the information as shown below: If you want to login to a remote ST7501 Server, enter the IP Address, User Name, Password and

the Communication Port of the target server correctly. Click Login to log in to the target server. If you want to login to a local host that is running ST7501 Server, check the Login local station

checkbox, then the local IP Address will be displayed automatically. Enter the User Name, Pass-word, and Communication Port of the local server for login. Click Login to login to the target serv-er.

3. The ST7501 LiveClient monitoring window will be displayed.

If your network environment need to set up proxy, click More >> to extend the login window, then click Proxy Settings to open the dialog. Then enter related information to link to your proxy server.

Available functions of the ST7501 LiveClient program will be enabled according to the role of your login account. For more details about the privileges of the user account, please refer to How to Manage User Accounts on page 41.


User's Manual - 13

ST7501 LiveClient User Interface

Menu Bar

Status Panel

F

CB

E

A

D

User NameStation Name Login Time (yyyy-mm-dd hh:mm:ss)Current Time (yyyy-mm-dd hh:mm:ss)

Menu Item Drop-down Options

System Lock / Enable Click On Image (Disable Click On Image) / Language / Second View / E-map / Launch Playback / Logout / Exit

Edit Manually Begin Recording (Manually Stop Recording) / Snapshot / Print / Record to EXE (3GP, AVI) / Find

View PTZ Panel / Two Way Audio Panel / Instant Playback Panel / Event Window / Full Screen / Minimize

Configuration

Camera Management (Insert Camera / Update Camera / Delete Cameras / Batch Insert Cameras) / User Management / Association Management / Event Management / Station Settings (General Settings / Network Settings / Recording Storage Settings / Recording Schedule Settings / Scheduled Backup Settings / Server Settings / Relay Settings) / Client Settings (Snapshot Settings / Recording Settings / View Settings / General Settings / Joystick Settings / Proxy Settings)

Layout Start Rotating (Stop Rotating) / Edit / ChooseHelp About

A. Menu bar B. Quick access bar C. Device tree D. Camera control panel (PTZ / Two way audio / Instant Playback control panel)E. Status panel F. Live video monitoring window G. Event window

G


14 - User's Manual

Quick Access Bar

Some buttons will be disabled if the selected devices do not support those functions.

Live Video Monitoring WindowThe "VIVOTEK" logo is displayed where no camera has been assigned to a video cell.

Icon Function Description

Exit Exit the system

Logout Log out from the current station

Lock Click to Lock the system for security concerns ( Unlock the system)

Volume Adjust the audio volume of the current video ( Mute)

Snapshot Capture pictures from the focus live video cell

Print Print out the pictures of focus live view window or all live video cells

Record to Media Record media in EXE/3GP/AVI format ( Recording Media)

Alert Sound Play sound when an event triggers

Switch Screen Switch the current window to another screen

Remove All Connections Remove all live videos from the live view window

Layout Change the layout of the live view window

Full Screen Maximize the live video cell

Page Up Switch to the previous live view page

Page Down Switch to the next live view page

Start / Stop Rotating Start or stop live view layout rotating

The red frame ( ) represents the current video cell.

Video Cell


User's Manual - 15

Device tree

Root Station Name (IP address)

Connected devices listed under the root stationCamera name (IP Address)

Connected devices that have been assigned to the default recording storage

Layout list

Icon Description

A station (The host that’s installed with ST7501 Server)

/ VIVOTEK fixed network cameraRed dot signifies that the camera is recording.

/ VIVOTEK PTZ network cameraRed dot signifies that the camera is recording.

/ VIVOTEK dome network cameraRed dot signifies that the camera is recording.

/ VIVOTEK video serverRed dot signifies that the video server is recording.

/ Digital input on / off

/ Digital output on / off

A layout of the live monitoring window

A station that’s not able to be connected currently.

A device that’s not able to be connected currently.


16 - User's Manual

Camera Control Panel

Pan/Tilt/Zoom (PTZ) Control Panel

There are two types of PTZ control: Digital (E-PTZ for megapixel cameras) and Mechanical (PTZ cameras or fixed cameras with camera control via RS-485). If your linked network cameras support PTZ/E-PTZ function, the option(s) will appear on the drop-down list. For detailed camera control settings, please refer to the user's manual of VIVOTEK network camera .

Click System > Enable Click On Image to use the mouse for the control of the PTZ and e-PTZ functions in the video cells for linked cameras. An icon will appear in the video cell as shown below.

You can control the PTZ function through joystick as well. For more information regarding to the joystick configuration, please refer to instruction on page 108.

Top left

Left

Bottom left

Focus nearClose

Start to auto pan

Zoom out

Up

Return to home position

Bottom right

Right

Top right

Down

Focus farZoom in

Open

Start to auto patrolStop auto panning/patrolling

Drop-down list of preset positions

Auto focus

Auto iris


User's Manual - 17

Two Way Audio Control Panel

The two way audio function allows the user to remotely communicate with people nearby the network camera.

For detailed information about How to Use the Talk Panel, please refer to page 85. Only cameras with the two way audio function can be added to the Talk Panel.

Language Selection

ST7501 currently supports multi-lingual user interfaces including: English, Deutsch, Español, Fran-çais, Italiano, 日本語, Português, 簡体中文, 繁體中文. If you want to select another language for the interface, please click System > Language on the menu bar to select the desired language. Please note that if you want to change the language option, a message will pop up to remind you to restart the system.

Remove all cameras from the Talk Panel

Click to play sound from the cameraClick to talk

Click to adjust volume

Selected device that can use the two way audio function

Click to play the selected sound on the client's side

If you want to use "User Defined" language, please prepare images and language strings, and upload the files to the following folders:

...\ST7501\Client\LiveClient\language\zz_UD (language string)

...\ST7501\Client\LiveClient\image (images)

Select sound from the file list


18 - User's Manual

Event Window

Click View > Event Window to open a window showing the real-time information for event triggers. If you want to hide this window, uncheck this option on the menu bar.

The Type field in the event window shows the event category and another field Description displays the percentage of motion in the detection window. You can go to the Configuration setting page of the connected device to set the percentage.

For more information about DI/DO settings, please refer to Association Management on page 46.

Video(TCP-AV) 2010/08/03 16:00:20

The default event window is fixed on the bottom of the LiveClient. If you want to change the event window as a popup page, please click Configuration > Client Settings > General Settings to switch the modes.

Event Window


User's Manual - 19

Instant Playback

Check View > Instant Playback to open the window on the panel.

The event trigger with recorded data will be attached an icon .

You can double-click an event on the list to playback the recorded video. Each event contains about 20-seconds recorded video clip. (The default event recording data is 20 seconds. For more information about event recording, please refer to page 58.)

Audio Control

The audio function will be enabled if the device is equipped with an internal or external microphone. For detailed audio control settings, please refer to page 129.

Instant Playback Window with slider bar, play, pause, and stop function

Uncheck this item if you want to hide this window.


20 - User's Manual

How to Manage Devices

Please follow the steps below to open the Camera Management window:a. Click Configuration > Camera Management on the menu bar (or right-click the station, then select

Camera Management).b. Then you can choose to insert, update, delete, or batch insert cameras.

Insert Devices

Please follow the steps below to add devices to a station:a. Click Configuration > Camera Management > Insert Camera on the menu bar (or right-click the

device/station, then select Camera Management > Insert Camera).b. The Camera Management - Insert window will pop up. The device tree managed by the station will

be displayed in the left Camera List window.c. Enter the Camera Name, address (or you can enter an IP address or a host name by Domain server,

and check Auto to get a camera name automatically) and configure the Connection Settings. If the camera is on the LAN, you can click Search Camera to detect all VIVOTEK network

cameras on the LAN. A Camera List window will pop up and show a list of detected cameras on the LAN. On the top of Camera List window, you can select "List the cameras which are not inserted" or "List all cameras". The items listed below will then change accordingly. You can click Mac, Address, Model, HTTP port to sort the items. Then select a camera from the list to insert to the station.

The streaming protocol determines how the live video stream is sent from the camera to the local computer. Please refer to the note on the next page for a detailed description of each transmission protocol. Specify the recommended live monitoring stream for the device. If you want to change the live viewing stream, please refer to page 21 to update the camera settings. Or you can right-click the desired cell, then select a desired stream. Please refer to Dual / Multiple Streams on page 32 for a detailed illustration.

Click Detect Model to detect the device. The Model Name and MAC Address of the device will automatically be displayed in the respective fields if the connection is successful.

d. If you want to make sure you are connected to the target device, click Connection Test to preview the live video from the device.

ba

ba


User's Manual - 21

If you want to use "HTTPS Port", please enable the HTTPs settings on the configuration page of the Network Camera first.

The characteristics of each protocol are shown in the following table:Protocol Description

UDP

UDP uses a simple transmission model without implicit hand-shaking dialogues for guaranteeing reliability, ordering, or data integrity. Thus, UDP provides an unreliable service and data grams may arrive out of order, appear duplicated, or go missing without notice. This protocol allows for almost real-time audio and video streams. However, network packets may be lost due to network burst traffic and images may be obscured. Activate UDP connection when occasions require time-sensitive responses and video quality is less important.

TCP

TCP provides the service of exchanging data reliably directly between two network hosts, whereas IP handles addressing and routing message across one or more networks. In particular, TCP provides reliable, ordered delivery of a stream of bytes from a program on one computer to another program on another computer. This protocol guarantees the delivery of streaming data and thus provides better video quality. The downside with this protocol is that the real-time effect is worse than that with UDP for a narrower bandwidth.

HTTPHTTP is a networking protocol for distributed, collaborative, hypermedia information systems. It’s the foundation of data communication for the World Wide Web. This protocol allows for the same quality as TCP and the users need not open a specific port for streaming under some network environment. Users inside a firewall can utilize this protocol to allow streaming data through.

HTTPS This protocol enables authentication and encrypted communication over SSL (Secure Socket Layer), which protects streaming data transmission over the Internet on higer security level.

c

d

c

c


22 - User's Manual

e. Configure Recording Settings: Recording Stream: By default, the stream source of the recording stream is stream 1, if you want to

change it later on, please refer to page 20 to update the camera settings. Pre-event time: Enter a number to decide how much time to record before an event is triggered. Post-event time: Enter a number to decide the duration of recording after an event is triggered.

For example: If both the Pre-event time and Postevent time are set to 10 seconds, a total of 20 seconds video will be recorded if an event triggers. This function is supported by the buffer area of ST7501 server (time shift cache stream).

Minimum pre-event time: Due to the limited cache memory of each network camera, the pre-event time of time shift cache stream on camera may be very short. Then you can choose to set pre-event recording on the ST7501 server. For example: To set up minimum 5 seconds. If the cache memory of the selected Network Camera can only support up to 3 seconds, the ST7501 Server will switch to enable pre-event recording for 5 seconds by itself, rather than request the time shift cache stream from the network camera server.

Please note that if you want to enable activity adaptive stream, we suggest you right-click the camera on the heirarchical management tree > Camera Settings > Audio and Video to activate "Time Shift Cache Stream" on the camera and select a stream source. This will help record complete pre-event recording.

Activity Adaptive Stream (active if possible): Check this item to enable activity adaptive stream recording and time shift recording. For cameras combined with time-shift cache stream and multiple streams features, user can make use of activity adaptive streaming for dynamic frame control.If you check Activate Activity Adaptive Stream and enable time-shift cache stream on the camera, only when an event is triggered on the camera will ST7501 Server record the full frame rate streaming data; otherwise, it will only request the I frame data during normal monitoring, thus effectively save lots of bandwidths and storage. Time

Bandwidth

Bandwidth

Activity Adaptive Streaming for Dynamic Frame Rate Control

I frame ---> Full frame rate ---> I frame

Continuous recording

post-10 sec.

pre-10 sec.

Trigger Activation

Pre-event time Post-event timee


User's Manual - 23

f. The device will automatically be assigned to the default recording group. Uncheck the item if you want to cancel this setting.

g. When all settings are completed, click Insert to add the device to the station. The device will be displayed under the left Camera List.

h. To insert additional devices to the station, repeat the above steps. i. When completed, click Close to exit the camera management window.j. Back to the main window, you will find the newly-inserted devices displayed under the station and the

live video in the video cell.

fg i

g


24 - User's Manual

Insert a Video Server

1. Left-click on your ST station, and then right-click to display the Camera Management command. Let your cursor stay on the command for a second and then move to the Insert Camera command. Click on the command to open its configuration window.


User's Manual - 25

2. See below for the steps to insert a Video Server along with its subordinate cameras.

2-1. You can uncheck the Auto checkbox to enter a name for the Video Server. If set to Auto and your video server already has a name, that name will be displayed in your device list.

2-2. Enter the Address of the video server - or - use the Search button to open a Search window. 2-3. If you enter its address and it is found after you click on the Detect Model button, its Model

Name and MAC Address will be listed. 2-4. Before you click the Detect button, you should enter the User Name and Password for access

to the video server. You should also confirm the Configuration Protocol, Configuration Port, Streaming Protocol, and the rest of the networking parameters.

2-5. You may select or deselect the checkbox in front of the recording storage option - or - use the pull-down menu to select the default group or a pre-configured storage group.

You might use the Connection Test button to verify if the stream comes from the device you prefer. 2-6. Click Insert to include the video server to your configuration.

The Video Server should now be listed on the Camera List. You can also use the Search button to poll the local area network for VIVOTEK's devices. You can

select to list all cameras or list those that have not been included in your current configuration. Click on a device, and its detailed information will immediately appear in the Camera Management

window on the left. For recording settings, please refer to revious pages.

12

3

4

5

6

12


26 - User's Manual

Update Devices

Please follow the steps below to update a via Camera Management window:a. Click Configuration > Camera Management > Update Camera on the menu bar (or right-click the

device/station, then select Camera Management > Update Camera).b. The Camera Management - Update window will pop up. The device tree managed by the station will

be displayed in the left Camera List window.c. Select a device from the list you want to update. Its related information will automatically be displayed

in the corresponding fields in the Camera Management window. Then you can modify Connection Settings and Recording Settings of the device.

d. After modifying the settings, you can click Connection Test to preview the live video from the device.e. When all settings are completed, click Update to enable the settings.

b

c

e

d

a


User's Manual - 27

Delete Devices from the ST7501 Server

Delete a device:Right-click the device on the device tree, then select Delete. A dialog box will pop up. Click Yes to delete the device along with the recorded data; click No to delete the device but retain the recorded data; click Cancel to cancel the delete action.

Delete more than one device at a time:a. Click Configuration > Camera Management > Delete Cameras on the menu bar (or right-click the

device/station, then select Camera Management > Delete Cameras). b. The Delete Cameras window will pop up. c. Select the devices you want to delete from the list, then click Delete.d. A dialog box will pop up. Click Yes to delete the device along with the recorded data; click No to delete

the device but retain the recorded data; click Cancel to cancel the delete action.e. When completed, click Close to exit the Delete Cameras window and return to the main window. The

deleted device will disappear from the station.

b

a

c

d

e


28 - User's Manual

Batch Insert Devices

Batch insert is a very useful function that allows user to search, filter, and import a row of devices to the station on the LAN at a time. The basic settings can also be applied to those inserted devices simultaneously.

Please follow the steps below to batch insert devices to a station:a. Click Configuration > Camera Management > Batch Insert Cameras on the menu bar (or right-

click the station, then select Camera Management > Batch Insert Camera).b. The Batch Insert Cameras window will pop up. Then click Search to open the Search Camera

window.c. On top of the Camera List window, you can select "List the cameras which are not inserted" or "List all

cameras". The items listed below will then change accordingly.d. Use the 4 Filters to narrow down the range of the wanted cameras from the list. IP Range: Type in a range of IP address to narrow down the list; the filter automatically filters after

you fill in a correct IP range.

b

c

d


User's Manual - 29

IP with prefix: Type in the prefix of the IP address to narrow down the list.

Model with prefix: The user can type in the prefix of the model name or the complete model name of the cameras to narrow down the list.

MAC with prefix: You can type in the prefix of the MAC address of the cameras to narrow down the list.


30 - User's Manual

e. When the list is filtered, you can select the cameras one by one or check Select All to add them to the batch insert list. Then click OK to finish searching.

f. The selected cameras will be shown on the batch insert camera list with the camera information and the connection status. When you click on a camera, a live view will show up on the right side for you to identify the cameras on the list. If you want to remove a camera from the list, click the trash can icon to delete it.

g

fh

j

i


User's Manual - 31

g. On the bottom of the window, there is a field for you to alter the camera settings including Connection Settings and Recording Settings. You can apply the new settings to each camera on the list, or click Apply to All to apply the same configurations to all the cameras. For more information about Connection Settings and Recording Settings, please refer to Insert Device on page 20 for detailed information.

When you modify the camera settings, once the connection information (User Name, Password, Configuration Protocol, Configuration Port, and Streaming Protocol) is not matched to the network environment, the camera will be disconnected and the status of the camera will become “Camera cannot be found” as shown below.

h. Specify host: If you want to add a camera to the list, click Specify Host to directly add a wanted camera. Click Add after filling in the correct information. The camera will be added to the list of the Batch Insert Camera window.

i. By default, all inserted devices will be applied to the default recording group. Uncheck Add to if you do not want to assign the selected devices to the default recording group.

j. Click Insert when all the settings are done. The settings will be applied.


32 - User's Manual

View Live Videos

The server will automatically add a newly-inserted device to the video cell for live viewing. You also can double-click the target device or drag-and-drop the target device from the device tree window to the video cell in the live video monitoring window.

Dual / Multiple Streams

For dual-stream devices, you can right-click on the focused cell to select stream 1 or stream 2. For multiple-stream devices, you can select from stream 1 ~ stream 4.

Refresh

Right-click the device, then click Refresh, the camera information will be refreshed from the server.

Streaming Server

Right-click the station or the device and click Output Streaming URL. A .txt file with streaming URL will pop up. Then you can use this URL to link to the live streaming through QuickTime Player.


User's Manual - 33

Camera Settings

Right-click the device, then click Camera Settings to open a web browser's session to the camera.

Remove Live Video from the Video Monitoring Window

There are two ways to remove a live video from the video cell: Method 1. Right-click the video cell and select Remove.

Method 2. Drag-and-drop the live view from the video cell to the device tree window.

If you want to remove all live videos from the video cells, please click on the menu bar.

You must have an IE browser rev. 6.0 or above for the management session.


34 - User's Manual

How to Change the ST7501 LiveClient Layout

Changing the Layout of the Live Video Monitoring Window

VIVOTEK ST7501 LiveClient supports up to 32-CH simultaneous video viewing on a single monitor and allows you to change the layout of the live video monitoring window based on the number of inserted devices.

Switch Video Channels

To move a video channel to another empty video cell, drag-and-drop the view to the target video cell.

To switch two different channels, drag-and-drop one view to the other, then the two different channels will be switched to the opposite

Configure Layout Mode

Click the Layout button on the quick access bar. Select a desired layout mode, and the layout window will be changed accordingly. Below we illustrate 8 types of layout modes and the corresponding page numbers:

Some layout modes (1 x 1, 2 x 2, 1 + 5, 3 x 3, 1 + 12, 4 x 4) will divide all video channels into several pages.

Layout mode Description Video page

1 x 1 32

2 x 2 8

1 + 5 4

3 x 3 3

1 + 12 2

4 x 4 2

5 x 5 1

1 + 31 1

More than 1 video page; rotation function is enabled

Only 1 video page; rotation function is disabled


User's Manual - 35

For example, under 3 x 3 layout mode, you can switch among the pages by clicking and on the quick access bar. To arrange the content of each page, manually drag-and-drop cameras from the device tree to the video cells on each page.

Rotating Video Pages

For layout modes that contain more than one page, ST7501 LiveClient offers the rotating function for displaying all video pages in turn. To enable this function, click on the Quick Access Bar, which will become Stop Rotating, and

the video pages will start to rotate so that the user does not have to click to move to the next page. To disable this function, click Stop Rotating, which will become on the Quick Access Bar.

You can also click Layout > Start to Rotate/Stop Rotating to enable/disable this function.

The default rotating time interval is 6 seconds. If you want to edit rotation settings, please refer to Rotation Settings on page 107.

Edit Layout

Please follow the steps below to save a layout:a. Arrange a layout mode and drag devices to their desired video cells.b. Click Layout > Edit > Save to > New on the menu bar. A Layout Name dialog box will pop up.

c. Enter a name for the the layout, then click OK to enable the setting.

1 2 3

164 5 67 8 9

10 11 1213 14 15

Page 1 Page 2 Page 3

17 18

1922

212023 24

25 26 27


36 - User's Manual

d. Back to the monitoring window, the new layout will be displayed under the device tree as shown below. You can save up to 10 layouts.

e. To change to another layout, double-click the layout items on the device tree, or click Layout > Choose on the menu bar to select a desired layout.

If you want to edit an existing layout, arrange a layout mode and drag devices to the desired video cells, then click Layout > Edit > Save to > New to save as a new layout or an existing layout to replace with the new one.

If you want to delete an existing layout, right-click the layout item on the device tree or click Layout > Edit > Delete on the menu bar to delete it.

Whenever you close the LiveClient or Playback programs and changes in screen layout have been made, you will be prompted to save your current configuration.


User's Manual - 37

Maximize/Minimize the Live Video Monitoring Window

Single View: to maxmize a video cell to the entire live video window

Double-click the video cell, or right-click the video cell and select Single View. The focused video will occupy the entire playback window as shown below.

To restore to the original layout, double-click the video cell or right-click the video cell and uncheck Single View.


38 - User's Manual

Full Screen: Maximize the live video monitoring window to the entire screen

Click Full Screen on the quick access bar or right-click the video cell and select Full Screen. In addition, you can also click View > Full Screen on the menu bar to maximize the live video monitoring window.

To restore to the original layout, you can right-click a video cell and uncheck Full Screen or click the Esc button on the keyboard to exit full screen mode.

Minimize: If you click View > Minimize on the menu bar, LiveClient will minimize to the Windows tool bar.

View Live Video on Dual Monitor

ST7501 also supports live video viewing on dual monitors, allowing you to manage maximum 32 channels on two screens concurrently. Moreover, the layout of the video monitoring window on different monitors can be set up individually.

Please follow the steps below to set up dual-screen mode:a. Set up dual monitors for your local computer.b. Launch ST7501 LiveClient on monitor 1.c. Click System > Second View on monitor 1, then the live video monitoring window will be displayed in

monitor 2 as shown below.

d. There are two ways to view live videos. One is to drag-and-drop the target device from the device tree window to the video cells. The other is to click any video cell on monitor 1 or monitor 2, then double-click the target device; the live video will be displayed in monitor 1 or 2 in accordance with your selection.

e. If you click Switch Screen on the quick access bar, the live monitoring window on monitor 1 and monitor 2 will swap.

Monitor 1 Monitor 2

ce


User's Manual - 39

View up to 32 channels simultaneously

If you select 4x4 layout on dual screens, you can view a maximum of 32 channels live video simultaneously. In this case, each layout contains 32 channels on 1 video page.

Using different layouts on each monitor

You also can select different layout for two monitors, simply click the Layout button on the quick access bar. Below is an example of the 2x2 layout with 4 video pages on monitor 1 and the 4x4 layout with 1 video page on monitor 2. You can click and to switch among the video pages.

Monitor 2 - page 1Monitor 1 - page 1

Monitor 1 - page 2Click

1 2

3 4

5 6

7 8

18 19 2021 22 23 24

25 26 27 28

29 30 31 32

17

Monitor 1 - page 4

Monitor 1 - 16 channel Monitor 2 - 16 channel


40 - User's Manual

View Live Video with Multiple Monitors

If you have multiple screens in your monitoring center, you can switch the ST7501 LiveClient Window among these screens.

If you have two monitors, click Switch Screen on the menu bar; the LiveClient window on monitor 1 will switch to monitor 2.

If you have three or more monitors, a drop-down list will be displayed when you click Switch Screen on the menu bar. The number of items on this list depends on the number of your screens. Select a

desired screen on the drop-down list and the LiveClient Window will switch to the specified screen.

Monitor 1 Monitor 2

Monitor 1Monitor 2Monitor 3 ......


User's Manual - 41

How to Manage User Accounts

ST7501 allows users to apply multiple user accounts to a station with five levels of user roles: Administrator > Power User > User > Operator > Guest. Each role has different permissions listed as shown below. Moreover, Administrators have the highest privileges, while Power Users can only add/edit users as Power Users, Users, Operators, and Guests.

The Default User Roles and Permissions of User AccountsFunctions \ User Roles Administrator Power User User Operator Guest DescriptionUser Management Manage user accounts

Camera Management Insert and configure the camera settings

Association Management

Access and modify the association settings

Access Event Management Access event management

Modify Event Management Modify event management

General Station Settings

Modify general station settings

Station Network Settings Modify network settings

Access Recording Storage/Recording Schedule Settings

Access the recording group and recording schedule

Modify Recording Storage/Recording Schedule Settings

Configure the recording group and recording schedule

Manually Record Enable the recording function manually

Scheduled Backup Settings Configure backup schedule

Access Server Settings Access server settingsModify Server Settings Modify server settings

Relay Management Allow user to manage station relaying settings

Client SettingsConfigure the client settings: snapshot, AVI, etc.


42 - User's Manual

Manage a User Account

Add a New User Accounta. Click Configuration > User Management on the menu bar (or right-click the station, then select

User Management).

Privileges \ User Roles Administrator Power User User Operator Guest Description

Modify Directories Add, remove and rename directories

Delete Camera Delete camera from the station

PTZ ControlPTZ control for PTZ cameras and speed domes in LiveClient

Device ControlControl the digital output or white light/IR illuminators of the cameras

Talk Control Two way audio function for the cameras

Access Camera Configuration Access the camera settings

Modify E-map Allow user to modify the E-map

Event Search Use built-in search engine to search specific events

Log Viewer Use built-in search engine to search the log

Backup Back up database manually

Record/Export MediaRecord live stream or export playback stream to local files

Playback Authority Allow user to access Playback


User's Manual - 43

b. The User Management window will pop up. The user accounts under the station will be displayed under the left User List tree.

c. Enter the User Name, Password, and specify the User Role of this user.d. Click Add to add the user account to the station. It will be displayed under the User List.

bc

d

d


44 - User's Manual

Permission of the User AccountAdministrator is granted with all access privileges, while other user roles' permission is limited. If you want to modify the permission, please login as the Administrator to configure the settings.e. Select a User account from the User List tree.f. If you want to set the limit of the permission of the user, click Permission tab to check or uncheck the

items.

g. If you want to limit the devices accessible by the user, click Accessible Cameras tab to select the desired devices.

g

e

f

hi


User's Manual - 45

If you want to remove access permission mentioned above from the account, the user will not able to operate some functions listed in the following warning dialog.

h. When completed, click Update to enable the new settings.

Delete the User Accounti. Click Delete, a delete user dialog will pop up. Click OK to delete the user account.

If the Administrator modifies or deletes the User Account, that modified user might be kicked off from the station.


46 - User's Manual

How to Set up Association ManagementST7501 LiveClient supports association management which allows the user to configure relative event trigger notifications of connected network devices. (Eg. DI/DO status on the device tree, motion detection windows appear in the video cell, the event list in the event window)

Association Management

Please follow the steps below to configure assocation settings:a. Click Configuration > Association Management on the menu bar (or right-click the station and

select Association Management).

c. The Association Management window will pop up. Check or uncheck the items and click Save to enable the settings. The items you've selected will also be displayed under the device tree.

For example:

d. If you want to rename the DI device, select the DI item and click the Rename button. It will be very convenient for you to recognize the target DI device.



ab

d


User's Manual - 47

To manually enable DI/DO settings, please right-click the video cell and select Set DO to enable (Trigger) or disable (Normal) the digital output of the linked device.

Before you configure the DI/DO Settings for ST7501, please enable DI/DO settings on your network device and set up the camera correctly on the configuration page. You can right-click the device and click Camera Settings to open the configuration page.


48 - User's Manual

How to Set up Event ManagementST7501 LiveClient supports event management which allows the server to respond to particular situations (events).

Event Management

Please follow the steps below to configure event management:a. Click Configuration > Event Management on the menu bar (or right-click the station and select

Event Management).

b. The Event Management window will pop up. Click New to set up a new event. When you finish the general settings, click Next to set up trigger source settings.

c. Click Add to select the trigger source by Device or Trigger Type.

Detect next event after 5 secs


User's Manual - 49

d. The Device List window will pop up. Select one or more devices and set the Notification Type. Depending on the trigger source, the Notification Type will be different. Then click OK to close the window.

e. The trigger source(s) will be listed on the window as shown below. If you want to add more Trigger sources, click Add and repeat d.~e. Then click Next to assign action(s) to the trigger source(s).

f. Click Add to open the Action Settings window.

There are several types of Action Settings. Email: The sever will send a notification via e-mail when a trigger is activated.

g. To enable this function, please set up the SMTP server first. Click SMTP Setting to open the window and refer to page 83 for detailed information.

h. Enter the related informtaion. You can modify the mail content in the blank. If you want to modify the content, click Insert Macro to select the parameter. When completed, click OK on the bottom to enable the setting.

e

f

gh


50 - User's Manual

Start to record on: The sever will start to record video from selected camera(s) when an event is triggered. i. Click Add Camera to select the target camera(s).j. The selected camera(s) will be listed on the left window below. When completed, click OK on the

bottom to enable the setting.

Move to preset location: The target camera(s) will move the shooting area to the preset location(s) when an event is triggered. k. To enable this function, please set preset locations on the camera configuration page first. l. Click Add Location to select preset location(s). m. The selected preset location(s) will be listed on the left window below. When completed, click OK

on the bottom to enable the setting.

Set DO: Select this option to turn on external digital output device(s) when an event is triggered. For more information about how to set DI/DO settings on the target camera, please refer to page 46. n. Click Add DO to select DO decive(s) and select a DO status (Normal or Trigger). o. The selected DO device(s) will be listed on the left window below. When completed, click OK to

enable the setting.

i

ij

lm

m

n

no

j

o


User's Manual - 51

GSM Short Message: The sever will send a short message to a GSM cell phone when an event is triggered. p. Please enter the Phone Number and open GSM Settings window to set related information if

necessary. When completed, click OK to enable the setting.

HTTP: This function allows user to send a CGI command to the linked network camera, such as pan/tilt/zoom function or enable DO devices. q. You can click Insert Macro to select the parameter. Please enter authentification information

i f necessary. For example: http://192.168.3.66/cgi-bin/admin/setparam.cgi?system_hostname=$(EventTime) $(CameraName)If you want to use special characters such as $-_.+!*'(),#%+$,@:;/?=&, please refer to the following table to transfer the Code (Hex). For example: http://192.168.3.66/cgi-bin/admin/setparam.cgi?system_hostname=123&456 --> http://192.168.3.66/cgi-bin/admin/setparam.cgi?system_hostname=123%26456

Please enter the country code if you use overseas call.

Character Code (Hex)! 21# 23$ 24% 25& 26' 27( 28) 29* 2A+ 2B

Character Code (Hex), 2C- 2D. 2E/ 2F: 3A; 3B= 3D? 3F@ 40_ 5F~ 7E


52 - User's Manual

r. The action(s) will be listed in the window as shown below. Then click Next to set up schedule(s) to the action(s). For more information about Schedule Settings, please refer to Recording Schedule Settings on page

60. You can assign more than one time frame to one action.


User's Manual - 53

s. When you finish schedule settings, click Next to review the detailed information of the new event settings.

t. Following is the detailed information of the new event setting. You can click Back to modify the event setting or click Finish to close the window.

u. Following is an example of an enabled event. You can click New to set up more events or click Close to exit the window.

Click to disable or modify the selected event

Click to remove the event


54 - User's Manual

How to Configure the Station General Settings

Select the target station from the device tree, then click Configuration > Station Settings > General Settings on the menu bar (or right-click the station on the device tree and select Station Settings > General Settings). The Station General Settings window will pop up.

Server SettingsIn this section, you can modify the Station Name.

Log SettingsIn this section, you can set up Log Settings for the station.

The ST7501 server allows user to search for the recorded log through ST7501 Playback. For more information, please refer to How to Search Logs on page 144. Log level: Select High (only record high-level logs), Normal (record high-level and normal-level logs),

Low (record all logs). For detailed information about log levels, please refer to page 145. Reserve Time: Enter the time interval that you want to reserve the log record. The maximum value is

365 days.


User's Manual - 55

How to Configure Station Network Settings

Select the target station from the device tree, then click Configuration > Station Settings > Network Settings on the menu bar (or right-click the station on the device tree and select Station Settings > Network Settings). The Network Settings window will pop up.

Port Settings Server port: The default server port is set to 3454. If you

change the server port, please enter the new value while logging the LiveClient next time.

RTSP port: The RTSP (Real-Time Streaming Protocol) controls the delivery of streaming media. By default, the port number is set to 554.

UPnP Settings Enable UPnP port forwarding: For client to access the

ST7501 Server from the Internet, select this option to allow the server to open ports on the router automatically so that video streams can be sent out from a LAN. To utilize of this feature, make sure that your router supports UPnPTM and it is activated.

Enable UPnP presentation: If you select this option, shortcuts to ST7501 server will be listed in My Network Places.

Proxy SettingsIn this section, you can enable, modify, or cancel Proxy Settings for ST7501 Server if your network devices are set up under a proxy.


56 - User's Manual

How to Edit Recording Groups

By default, all devices are assigned to the default recording group. You can manually remove a device from the default recording group. However, only those devices which belong to a recording group can produce recorded media files.

Another purpose of setting recording group is that you can divide all the managed devices into several recording groups, and for each recording group, you can assign several hard-disks (with recording paths) to store media data. The live media data will be stored in the first assigned hard-disk initially, and when the available space of the first hard disk reaches the preset reserved space limit, the media data will be stored in the second disk and so on. If the available space of the last disk approaches the reserved space, the recorded files in the first disk will be erased and overwritten with new media data. This procedure is called "Cyclic Recording".

Recording Storage Settings

Please follow the steps below to set up recording groups for a station:a. Click Configuration > Station Settings > Recording Storage Settings on the menu bar (or right-

click the station on the device tree and select Station Settings > Recording Storage Settings). You can also right-click DefaultGroup under the station and click Recording Storage Settings since all devices are assigned to the Default Recording Group by default settings.

b. The Recording Storage Settings window will pop up.


User's Manual - 57

Defult Storage Group SettingsThe following example shows the default storage group settings. You can click Rename to modify the group name or click Delete to remove the default settings.

c. The default recording path is C:\Recording. The total space and free space of the disk is shown on the right for reference.

d. Add Local Path: Click to add another recording path on your local computer. A Select Path dialog will pop up as shown below. When all settings are complete, click OK to enable the settings, or click Cancel to discard the settings.

e. Add Network Path: Click to add a network storage for recorded data. Please refer to page 82 for detailed information about how to add a new network storage server. Then double-click the Path to assign a specific folder as a new recording path.

c

d

Click those buttons to modify the file folder under D:\

e


58 - User's Manual

f. To modify the settings of a path, select the path from the list, then click Change settings to modify.g. To delete a path, select the path from the list and click Delete path. A warning dialog box will pop

up as shown below.

h. By default, all devices are assigned to the Default Recording Group in the window on the right. You can select device(s) from the list and click << to delete device(s) (or right-click the device under DefaultGroup tree to delete it). Note that a Delete Camera dialog box will pop up. Click Yes to delete the device along with the recorded data; click No to delete the device but retain the recorded data; click Cancel to cancel the delete action. Please note that only those designated devices can record videos.

i. Click >> to add devices to the DefaultGroup.

j. Delete recorded data older than the duration: If you only want to retain recorded data for a duration, check this item and enter a number of day(s). In addition, since ST7501 Server will do "cyclic recording" automatically, the oldest file will be overwritten by the latest one when the maximum capacity is reached.

k. When completed, click Apply to confirm and save your settings. If you want to cancel all of your editing, click Restore to return to the previous settings or click close to discard the settings.

h

h i

h

j

k


User's Manual - 59

Add New Recording Group(s)If you want to add a new recording group, click Add to give a name to the new recording group, which will be displayed on the drop-down list.The following is an example of recording group list.

Please refer to the following limits when you set up recording group(s): The maximum number of devices in a recording group is 32-CH. One recording group can be assigned with several recording paths and do cylic recording; while one recording

path should only be assigned to one recording group.


60 - User's Manual

How to Edit Recording SchedulesAfter editing recording storage settings, you can begin to edit recording schedules for the devices in a recording group. By default, all devices are assigned to the default recording schedule (Please refer to the default time frame settings on page 64). Therefore, once you insert a device to the station, the ST7501 Server will begin to record live video according to the default recording schedule. You can also manually remove a device from the default recording schedule. Please note that you cannot assign recording schedules to those devices which have been deleted from a recording group.

The following is an illustration of a set of recording schedules, which are composed of several time frames. Each time frame has its own time segments, period of time, repeat interval, and recording mode. You can create different recording schedules with simple or complex time frames based on your needs.

In addition, you can arrange the priority of each time frame according to its importance. The recording schedule with the highest priority will be applied first. This capability is very useful because you can specify a new time frame with the highest priority temporarily without modifying the other time frames.

Features of the recording schedules: Each device can be assigned to only one recording schedule. Each recording schedule may contain many time frames. Each time frame has its own repeat frequency and recording mode.

To save time editing recording schedules and time-frames, we also provide a useful template function to save your time on schedules/time-frames settings. That is, you can save a specified schedule and download it as a template for future use or upload a well-arranged schedule template designed by others.

Please note that after you save the recording settings in the server, the recording schedule will begin automatically according to your settings.

Router

Time Frame a

Recording Schedule 1

Time Frame b

Time Frame n

Time Frame y

Recording Schedule N

Time Frame z

Devices in Recording Group


User's Manual - 61

Edit Schedule List

Please follow the steps below to set up the recording schedules:a. Click Configuration > Station Settings > Recording Schedule Settings on the menu bar (or right-

click the station and select Station Settings > Recording Schedule Settings).

b. The Recording Schedule Settings window will pop up. By default, all cameras under the station are assigned to Default Schedule, Default Time Frame, and Default Camera List.

Add Schedulesc. To add a new recording schedule, click Add to enter a name in the Schedule Name dialog box for the

new schedule. Click OK to confirm the settings or Cancel to discard the settings. The new recording schedule will be displayed on the schedule drop-down list.

Rename Schedulesd. To rename an existing schedule, select the schedule from the schedule drop-down list and click

Rename. A Schedule Name dialog will pop up for you to fill in a name for the new schedule. Click OK to confirm the settings or Cancel to discard the settings. The new recording schedule will be displayed on the schedule drop-down list.

Delete Schedulese. To delete an existing schedule, select the schedule from the schedule drop-down list and click Delete.

A Remove Schedule dialog box will pop up. Click OK to confirm or Cancel to discard the settings.

d ec

dc e

b


62 - User's Manual

Load/Save Schedule Templatesf. If you have a schedule template with time frame settings, you can upload it to simplify the editing of the

schedule. Click Load Template, and a Load File dialog box will pop up. Select the template file and click Open to load.

g. If you want to save a schedule as a template for future use, select the schedule from the schedule drop-down list and click Save as Template. A Save File dialog box will pop up for you to save the template file.

f

g

gf


User's Manual - 63

Edit Camera List

Please follow the steps below to assign a device to a recording schedule:a. Select a recording schedule on the schedule drop-down list.b. By default, all devices under the station are assigned to the Default Schedule.c. Click << to remove devices from the Default Schedule. Click >> to add devices to the Default

Schedule. d. Click Apply to confirm or Close to discard the settings.

If you add a Network Device that does not belong to any Recording Group, a warning dialog will pop up as shown below. For more information about how to set up Recording Group(s), please refer to Recording Group Settings on page 56.

b

c

d

a


64 - User's Manual

Edit Time Frame List

Default Time Frame: Weekly (Day-based), Mon.~Sun., 24-hour, continuous recording

Click Edit to open the Default Time Frame settings page as shown below.


User's Manual - 65

Add New Time Frames

Please follow the steps below to add new time frames to a schedule:a. Select a recording schedule from the drop-down list.b. Click Add to open the Time Frame Settings window.

c. Enter a name for the new time frame.d. If you have a time-frame template, you can upload it to simplify the editing of the schedule. Click Load

Template and the Load File dialog box will pop up. Select the template file to load. e. To edit the new time frame, select a Repeat Frequency from the drop-down list and edit the time

segments, applicable days, applicable period of time, and repeat time interval. For the detailed settings of each repeat frequency, please refer to The Concept of Repeat Frequency on page 67.

f. When completed, click Save to enable the settings.g. If you want to save this time frame as a template for future use, click Save as Template. A Save file

dialog will pop up for you to save the template.

a

b

cd fg

e


66 - User's Manual

h. If you want to add additional time frames to the schedule, repeat the steps above. i. Close the window when you finish the time frame settings.j. Back to the Recording Schedule Settings window, the new time frame will be displayed on the Time

Frame List.k. If you want to edit an existing time frame, select if from the Time Frame List and click Edit to set up.l. If you want to delete an existing time frame, select if from the Time Frame List and click Delete.m. If you want to change the priority of a time frame, select it from the Time Frame List and click Up or

Down to shift its position. The time frame on the top of the list has the highest priority.

Recording Settingsn. Select one of the following Recording Modes for the time frame: None: No recording action. Continuous: 24-hours continuous recording. If you want to enable Activity Adaptive Streaming,

please refer to page 22 for detailed illustration. Event: The server will start to record only when an event is triggered. The recording time length

depends on the settings in Recording Group Settings. The default time length is 20 seconds (10s pre-event time plus 10s post-event time). Please refer to page 58 for more information. For more information about event catagories, please refer to page 139 for detailed illustration.

o. Select Trigger Source(s): Motion Detection, IVA (Intelligent Video Analysis), PIR, and Tamper Detectionp. Select the status of Digital Input(s): Trigger State or Normal Stateq. Click Apply to confirm the settings. Then close the window when you finish the recording schedule

settings.

jn

m

q

k l

o

p


User's Manual - 67

The following diagrams show the frame rate variation of two recording modes:1. Continuous recording + Activity adaptive recording (help save bandwidth and storage)

2. Event recording

The Concept of Repeat Frequency

ST7501 offers the following types of repeat frequency. The definition of each type is listed in the following table:Repeat Frequency Discription

Daily Setting Specify arbitrary time segments within a day, Repeat the segments every N days in the specified period of time

Weekly Setting (Day-based)(Default Time Frame)

Specify arbitrary time segments within a day, Apply only on selected days of a week, Repeat the segments every N weeks during the specified period of time.

Weekly Setting (Periods in a week) Specify arbitrary time segments within a week, Repeat the segments every N weeks during the specified period of time.

Monthly Setting (Day-based)

Specify arbitrary time segments within a day, Apply only on selected days of a month, Repeat the segments every N months during the specified period of time.

Yearly Setting (Day-based) Specify arbitrary time segments within a day, Apply only on selected days of a year, Repeat the segments every N years during the specified period of time.

Time

Bandwidth

Continuous Recording I frame ---> Full frame rate ---> I frame

Event Recording

Time

Bandwidth

No recording data ---> Full frame rate ---> No recording data


68 - User's Manual

Repeat Frequency: Daily Setting

To set up daily repeat frequency, please configure the following items: Daily time segments, applicable period of time, and repeat time interval.

Set up daily time segments

You can specify several time segments within a day. The numbers 0~23 on the hourly timeline control bar (the purple rectangles) represent the 24 hours in a day.

There are two ways to define time segments: one is to use the computer mouse to manipulate the timeline control bars; the other is to fill in the precise start and end time values in the corresponding fields.

Add time segments: Choose either step 1 or step 2 to set up1. Use the mouse to drag the timeline bars:

a. Left-click the daily timeline control bar (the purple rectangles) and drag the mouse. b. The corresponding time segment will also appear in the Start Time and End Time fields. Click Add,

then the red timeline bars representing new time segments will appear as shown below. You can drag multiple time segments within a day. In the following illustration, the yellow arrows show the dragging direction of the mouse. You can drag from left to right or the opposite.

Daily time segments *You can drag the daily timeline bar for more than one time segment per day.

Applicable period of time

Repeat time interval

Daily timeline control bar


User's Manual - 69

2. Fill in the precise Start Time and End Time: a. Directly enter the value in the Start Time and End Time fields, then click Add.b. The corresponding red timeline bar will automatically appear as shown below.

Delete time segments: Choose either step 1 or step 2 to set up1. Use the mouse to erase the timeline bar: Right-click on an existing red timeline bar and drag the

mouse. A green timeline bar representing the deleted part of the time segment will erase the red bar as shown below.

In the following illustration, the green arrows show the dragging direction of the mouse. You can drag it from left to right or the opposite.

2. Use the delete button to remove the entire timeline bar: a. Click an existing red timeline bar or left-click the daily timeline control bar (the purple rectangles)

and drag the mouse.b. The corresponding time segment will appear in the Start Time and End Time fields.c. Click Delete, and the selected timeline bar will disappear.

a b

ac

b


70 - User's Manual

Set up applicable period of time

For repeat frequencies, you can set up the applicable date and period of time for the time frame. a. Specify the start date and time in the Start field. A calendar date selector will appear when you click

on the drop-down list of date. Click or to select the month, then pick a desired day in the calendar.

b. Specify the end date and time in the End field if you have an end time for applying this time frame. If you do not have a terminating time for this time frame, select Never Stop.

Set up repeat time interval

The repeat time intervals is "every N day(s)" as shown below. Repeat every 1 day means the time frame would apply for every day within the period of time.

Click to select a yearClick to select a month from the drop-down list

ba

Click here to move the focus to the current date


User's Manual - 71

Repeat Frequency: Weekly Setting (Day-based)

To set up Weekly (Day-based) repeat frequency, please configure the following items: Daily time segments, applicable days within a week, applicable period of time, and repeat time interval.


Please refer to page 68 for detailed instructions.

Set up applicable days within a week

For repeat frequency--"Weekly (day based)", you can apply the time segments only on selected days of the week.




The repeat time intervals is "every N week(s)" as shown below. Repeat every 1 week means the time frame would apply for every week within the period of time.

Daily Time segments *You can drag more than one time segment per day.

Applicable days within a week



Daily timeline control bar (24h)


72 - User's Manual

Repeat Frequency: Weekly Setting (Periods in a week)

To set up Weekly (Periods in a week) repeat frequency, please configure the following items: Time segments within a week, applicable period of time, and repeat time interval.

Set up time segments within a week

You can specify several time segments within a week. The weekly timeline contol bar represents the 7 days of a week, and the daily timeline contol bar represents the 24 hours in a day. The daily timeline control bar is only valid when one of the days on the weekly timeline control bar has been selected.

There are two ways to set up time segments: one is to use the computer mouse to draw the timeline control bars; the other is to fill in the precise start and end time value in the corresponding fields.

Add time segments: Choose either step 1 or step 2 to set up1. Use the mouse to drag the timeline bars:

a. Click on a day on the weekly timeline control bar. The selected bar will turn green.b. Left-click the daily timeline control bar and drag the mouse. c. The corresponding time segment will also appear in the Start Time and End Time fields. Click Add,

then the red timeline bars representing new time segments will appear as shown below. You can drag multiple time segments within a day and a week. In the following illustration, the yellow arrows show the dragging direction of the mouse. You can drag from left to right or the opposite.

Time segments within a week *You can drag more than one time segment per week.



Weekly timeline control bar

Daily timeline control bar (24hr)

ab

c


User's Manual - 73

2. Fill in a precise Start Time and End Time: a. Directly select a day and enter the value in the Start Time and End Time fields, then click Add.b. The corresponding red timeline bars will automatically appear as shown below. The following is an example of an extended time segment from Mon. 8:00 to Fri. 19:00.

Delete time segments: Please refer to page 69 for detailed instructions.





a

b


74 - User's Manual

Repeat Frequency: Monthly Setting (Day-based)

To set up Monthly (Day-based) repeat frequency, please configure the following items: Daily time segments, applicable date(s) of a month/ day(s) of a week, applicable period of time, and repeat time interval.



Set up applicable date(s) of a month/ day(s) of a week

For repeat frequency--"monthly (day-based)", you can apply the time segments only on selected days of a month. There are two types of repeat frequencies: Date(s) of a month and Day(s) of a week.

Daily time segments *You can drag more than one time segment per day.

Timeline control bar (24hr)

Applicable date(s) of a month/ day(s) of a week




User's Manual - 75

Repeat by date(s) of a month: Select date(s) from the calendar, and it will be displayed on the right blank as shown below.The following example refers to the 1st ~ 5th day of a month.

Repeat by day(s) of a week: Select day(s) from the calendar, and it will be displayed on the right blank as shown below.The following example refers to the 1st ~ 5th Friday of a month.




The repeat time intervals is "every N month(s)" as shown below. Repeat every 1 month means the time frame would apply for every month within the period of time.


76 - User's Manual

Repeat Frequency: Yearly Setting (Day-based)

To set up Yearly (Day-based) repeat frequency, please configure the following items: Daily time segments, applicable date(s) of a year/ day(s) of a week, applicable period of time, and repeat time interval.



Set up applicable date(s) of a month/ day(s) of a week

For repeat frequency--"yearly (day-based)", you can apply the time segments only on selected days of a year. There are two types of repeat frequencies: Date(s) of a year and Day(s) of a week.

Daily time segments *You can drag more than one time segment per day.

Timeline control bar (24hr)

Applicable date(s) of a year/ day(s) of a week




User's Manual - 77

Repeat by date(s) of a year: Select date(s) from the calendar, and it will be displayed on the right blank as shown below.The following example refers to the 1st ~ 5th day of a year.

Repeat by day(s) of a week: Select day(s) from the calendar, and it will be displayed on the right blank as shown below.The following example refers to the January 1st ~ 5th Friday of a year.




The repeat time intervals is "every N year(s)" as shown below. Repeat every 1 year means the time frame would apply for every year within the period of time.


78 - User's Manual

How to Manually Begin /Stop RecordingBy default, all devices are assigned to the default recording storage and default recording schedule. Therefore, once you insert a device onto the station, the ST7501 Server will begin to record live video according to the default recording schedule. Please refer to How to Edit Recording Schedules on page 60.

However, if you have changed the default schedule, you can manually click Manually Begin Recording to enable a device without setting up a recording schedule. Please follow the instructions below to manually begin recording.

Select the device from the device tree under Default Group, then click Edit > Manually Begin Recording on the menu bar (or right-click the device and select Manually Begin Recording). The string on the menu bar will turn into Manually Stop Recording as shown below and the ST7501 Server will start to record video from the target camera. Please note that its priority will be higher than the recording schedule, so it will continue unless you click Manually Stop Recording. After you click Manually Stop Recording, the device will then follow the preset recording schedule.


User's Manual - 79

How to Edit Scheduled Backup SettingsST7501 LiveClient supports scheduled backup which allows the user to back up the recorded data in another disk.Please follow the steps below to enable scheduled backup settings:a. Click Configuration > Station Settings > Scheduled Backup Settings on the menu bar (or right-

click the station and select Station Settings > Scheduled Backup Settings).

b. The Scheduled backup settings window will pop up.

Select Backup Sourcec. Check Enable schedule backup.d. Select the data source you want to backup. If you check Selected cameras, you can click >> or << to

choose the data source that you want to backup.

cd


80 - User's Manual

Setup Backup Schedulef. Fill in a desired time and click >> to add the backup time. Please note that the backup time interval

must not less than 1 hour. For example, 23:40 and 00:15 are not allowed to exist simultaneously. In the following example, the server will backup the recorded data at 12:00 PM and 23:00 PM everyday

once you save the settings.

The following diagram shows the backup schedule and backup data:

Select Backup Targetg. Click Browse... to select a path (local path or network storage) to store the backup data. Please

note that the disk for backup data should be different from the original recording path, or a warning message will pop up as shown below. For more information about how to set up recording path, please refer to page 57.

h. Select a maximum size for backup folder. The server will divide backup data into the following size: VCD (650M), DVD (4.7G), Customize, or Unlimited size according to your choice.

i. Check Delete old backups if space is insufficient if you want to do cylic backup due to the limited size of the hard disk.

Other Optionsj. If you only want to backup the recorded data of events, select Backup only events and fill in the pre-

and post-event time.

ghi

Server start 12:00

2010/01/2423:00

2010/01/2412:00

2010/01/2523:00

2010/01/25

2nd backup data

1st backup data

3rd backup data

4nd backup data

f

j


User's Manual - 81

How to Configure Station Server SettingsST7501 LiveClient supports Server Settings including DDNS Settings, Network Storage Settings, and SMTP Settings.Select the station from the device tree and click Configuration > Station Settings > Server Settings to open the page (or right-click the station and select Station Settings > Server Settings).

DDNS Settings

Since the public IP of ST7501 Server may be a dynamic IP address, DDNS service will give it a fixed domain name. Select a DDNS provider from the provider drop-down list. VIVOTEK offers 2bthere.net (Safe100.net), a free dynamic domain name service, to VIVOTEK customers. Please refer to the user's manual of VIVOTEK's network camera for detailed DDNS settings.


82 - User's Manual

Network Storage Settings

The ST7501 Server allows user to set up network storage path(s) for recorded files. Please follow the steps below to add a new network storage path.a. Click Add to open the Network Host Window.b. Fill in the related information for the network host. Then click OK to save the new settings.

c. If you want to add more network host(s), please repeat step a. b.

a

b


User's Manual - 83

SMTP Settings

ST7501 Server allows user to set up SMTP Server to send mail alert when event triggers. For more information about how to set up event management, please refer to page 48.Please follow the steps below to configure the SMTP Server:a. Click Add to open the SMTP Settings page.b. Enter the related information of your mail server. If your SMTP server requires a secure connection

(SSL), check Use SSL.c. Click OK to enable the settings.d. Then the new information will appear on the SMTP Settings window as shown below.

b

a

c

dIf you have more than one SMTP server, you can click to arrange the priority.


84 - User's Manual

Relay Settings

The ST7501 server can be set as a sub-station of VAST, the VIVOTEK professional central management software, so as to construct a hierarchical management architecture. Following is an illustration for two-level hierarchical architecture:

For VAST to set ST7501 as a sub-station, please follow the instruction below to enable the Relay Settings first.a. Click Configuration > Station Settings > Relay Settings on the menu bar (or right-click the station

on the hierarchical management tree and select Station Settings > Relay Settings). b. The Relay Settings window will pop up. Check Allow Relay Connection and enter a Password.

Then click OK to enable the settings.


User's Manual - 85

How to Use the Talk PanelST7501 LiveClient supports the two way audio function which allows the user to communicate with people around the network camera. Please enable the two way audio function on the camera side.The following is an illustration of the two way audio function:

Add a Camera to the Talk Panel

There are several ways to add a Network Camera to the Talk Panel:Drag-and-drop a camera from the video cell or from the device tree to the talk panel as shown below. You can also right-click the target camera or the video cell, then click Send to Talk Panel on the popup menu.

Audio transmitted from operators

Audio transmitted from network camera

Network Camera with internal or external microphone


86 - User's Manual

An icon with the camera name will be displayed in the Talk Panel.

Please note that you cannot Talk and Play Sound at the same time. When you are talking or playing sound, you cannot add other cameras to the Talk Panel. If you want to add more

cameras to the Talk Panel, please Stop Talking and Stop Playing first.

Click to stop talking Click to stop playing

Remove all cameras from the Talk Panel

Click to play sound from the camera

Click to talk

Click to adjust volume

Click to play the selected sound on the client side

Select sound from the file list


User's Manual - 87

Remove a Camera from the Talk Panel

Remove a camera Drag a camera from the Talk Panel and drop to the hierarchical management tree window as shown

below. The camera icon will disappear.

Remove all cameras Click , all cameras in the Talk Panel will be removed.


88 - User's Manual

How to Configure E-map SettingsST7501 LiveClient supports intuitive E-map function which allows users to upload E-maps for overall devices management.Click System > E-map to open E-map Settings Page:

Upload an E-map

Click to search for E-map(s) to upload.

The uploaded E-maps will be listed under the E-map list tree.

If the uploading procedure fails, please compress the image size of your map (< 5MB) and try again.


User's Manual - 89

User Interface of E-map Settings Page (View Mode)

Double-click an E-map on the tree, it will be displayed on the E-map window as shown below. There are two operation modes of E-map settings page: "View Mode" and "Edit Mode". The following is the "View Mode" illustration.

A. Menu bar B. Quick access bar C. E-map list tree D. E-map window E. Status panel

Right-click the E-map, then you can edit, rename, or delete the E-map.

B

A

C

ED


90 - User's Manual

Right-click an E-map on the tree and click Edit or click on the Quick Access Bar, it will switch to edit mode.

Quick Access Bar

Status Panel


Zoom in Zoom in the E-map

Zoom out Zoom out the E-map

Default size Adjust the E-map to default size

Upload Upload E-map to the login station

View Mode Click to switch to view mode

Full Screen Extend the E-map settings page to full screen

Save Save E-map settings



User's Manual - 91

User Interface of E-map Settings Page (Edit Mode)

A. Menu bar B. Quick access bar C. E-map list tree D. Device tree E. Map preview F. E-map window G. Status panel

Right-click the E-map, you can download, rename, or delete the E-map.

B

A

C

D

E

GF

Download the E-map to E-map window


92 - User's Manual

Device Management

Please follow the steps below to edit an uploaded E-map.a. Double-click the E-map you want to edit, it will be displayed on the E-map window. b. Use Quick Access Bar to adjust the size of the E-map. In edit mode, you can also use your mouse to

drag the position of the E-map and zoom in or zoom out the E-map.c. Drag-and-drop the connected devices to the E-map according to your deployment.

d. Right-click the device icon on E-map, you can rotate the direction or delete the device. The device can be rotated in 8 derections as shown below.

e. You can also drag the DI/DO device under the linked device onto the E-map. If you want to change the status of the DO device, double click the DO icon on E-map.

f. Click on the Quick Access Bar to save the new settings.

b

c



The red frame twinkling around the device means there is event trigger(s) going on.Meanwhile, a live view dialog will pop up beside the model.

For more information about DI/DO settings, please refer to Association Management on page 46.


User's Manual - 93

Live View Dialog Settings

Click Configuration > E-map Settings to open the E-map Settings dialog, then you can choose to Open Live View Dialog or to Send to Single View when you double-click the device deployed on the E-map.

Open Live View Dialog

Select Open Live View Dialog: When you double-click the device icon on the E-map or when an event triggers, a live view dialog will pop up beside it. It is the default setting in E-map Settings window.

Send to Single View

Select Send to Single View: When you double-click the device icon on the E-map, it will open a single view on the ST7501 LiveClient.

If you have set up dual monitor, it will be automatically sent a single view to the second monitor.Monitor 1 Monitor 2


94 - User's Manual

E-map Link

After completing device deployment on your E-map, you can link an E-map to another E-map.Please follow the steps below to configure E-map link:a. Select a map you want to edit and enter Edit Mode.

b. Drag-and-drop another E-map onto current E-map. A blue frame will appear as shown below. For example: Link Map1 to Map2 by dargging Map2 onto Map1

c. Use to move the position of the blue frame.

The live view dialog also supports click on image, PTZ, and e-PTZ as long as the linked device supports and enables those functions. To enable those function on E-map, please check the item "Enable click on image" on the menu bar of LiveClient as shown below. Then an icon will appear in the live view dialog for you to control the cameras.


User's Manual - 95

d. Right-click the blue frame to Resize or Delete it.

Click Resize, some nodes will appear around the blue frame. Then You can drag the nodes to move the position, rotate the direction, adjust the size, and change the shape.

e. Click on the Quick Access Bar to save the new settings.

f. If you want to set additional map links, please repeat steps a. ~ e. For example: Link Map2 to Map3 by dargging Map3 onto Map2

g. Click on the Quick Access Bar to save the new settings.

resize change the shaperotate the direction

move the position


96 - User's Manual

h. Test the web links. Click on the Quick Access Bar to switch to view mode. Double-click the blue frame on Map1, it will automatically switch to map2. Then double-click the blue

frame on Map2, it will automatically switch to map3.

Map 1

Map 2

Map 3


User's Manual - 97

How to Configure Client SettingsIn Client Settings, you can configure Snapshot Settings, Recording Settings, View Settings, General Settings, Joystick Settings, and Proxy Settings.

Snapshot Settings

Please follow the steps below to configure snapshot settings:a. Click Configuration > Client Settings > Snapshot Settings on the menu bar to open the Snapshot

Settings window. b. Select a picture format for snapshots (BMP or JPEG). If you select JPEG format, you can adjust the

recompression quality (from 1 to 100). Note that a higher value would generate higher picture quality but lower compression rate.

c. Enter a filename prefix for the snapshots.d. The default storage path for snapshots is C:\Program Files\VIVOTEK Inc\ST7501\Client\LiveClient\

Snapshot. If you want to change the storage path, click Browse to select another folder.

e. If you check Generate a file name automatically, ST7501 will directly save snapshots with the following filename format to the storage folder.

bc

d

Snapshot_20100125_173015_01.jpg

File name prefix Date and time (YYYYMMDD_hhmmss)

Serial number of snapshots

Picture format

eThe recompression quality is only enabled in MPEG-4 streaming. If your stream source is MJPEG, the system will directly save the JPEG image without recompression.


98 - User's Manual

If you uncheck Generate a file name automatically, the Save file dialog box will pop up when you take a snapshot. The file name prefix will automatically be displayed in the Save File dialog box.

Take a Snapshot

Please follow the steps below to take a snapshot of the live video stream:a. Select the video cell of which you want to take a snapshot.b. Click Snapshot on the quick access bar, or right-click the video cell and select Others >

Snapshot from the popup menu. You also can click Edit > Snapshot to take a snapshot.

c. The snapshots will be found in the preset storage folder on your local computer.


User's Manual - 99

Recording Settings

The ST7501 Server allows you to record the live video in EXE, 3GP, or AVI format to your storage folder.

Type 1: Record to EXE Record video as an EXE file. The EXE is not only a media file but also a built-in media player. When user execute the EXE, the media file will be played automatically. There is no need to install any other program. For more information about how to use the EXE player, please refer to page 103.

Please follow the steps below to configure EXE record settings:a. Click Configuration > Client Settings > Recording Settings on the menu bar to open the Recording

Settings window.b. Select EXE as the Record Type.c. The default storage path is C:\Program Files\VIVOTEK Inc\ST7501\Client\LiveClient\Record. If you

want to change the storage path, click Browse to select another folder.d. Select the Length of each file-- Maximum Size (10~2000MB) or Maximum Time Interval (1~150

min).

e. Click OK to enable the settings.

Type 2: Record to 3GPRecord video as a 3GP file. 3GP file is a standard MP4 format compatible with players such as VLC, QuickTime, or Real players. Choose this type if you has already installed one of these players.

Please follow the steps below to configure 3GP record settings:a. Click Configuration > Client Settings > Recording Settings on the menu bar to open the Recording

Settings window.b. Select 3GP as the Record Type.c. The default storage path is C:\Program Files\VIVOTEK Inc\ST7501\Client\LiveClient\Record. If you

want to change the storage path, click Browse to select another folder.d. Select the Length of each file-- Maximum Size (1~2000MB) or Maximum Time Interval (1~150 min).

b

cd


100 - User's Manual

e. If you check "Record with only standard codec", the video from old models (VIVOTEK 6000-series products) using G7221/G729A/H.263 codec will not be recorded.

f. Click OK to enable the settings.

Type 3: Record to AVIRecord video as an AVI file, which uses the popular codecs pre-installed in the Windows OS. Please note that the speed may be slower due to the need of decoding the video/audio and re-encoding both into a compatible codec.

Please follow the steps below to configure AVI record settings:a. Click Configuration > Client Settings > Recording Settings on the menu bar to open the Recording

Settings window.b. Select AVI as the Record Type.c. The default storage path is C:\Program Files\VIVOTEK Inc\ST7501\Client\LiveClient\Record. If you

want to change the storage path, click Browse to select another folder.d. Select the Length of each file-- Maximum Size (1~2000MB) or Maximum Time Interval (1~150 min).

b

cd

e

b

cd

ef g

Due to the AVI file has a limitation on the maximum file size of 2G bytes, if the setting “time length” generates data larger than 2G bytes, several files will be created.


User's Manual - 101

e. Select the frame rate/ per second. f. To modify the video compression settings, click Video Compression Setting to open the AVI Video

Compression Setting window. Select the desired video compression algorithm, compression quality, key frame intervals, and data rate in the corresponding fields.

To modify the settings of the compression algorithm: Click Configure, then a dialog box will pop up for you to modify the settings. The dialog box will be different according to the compressor you select.

To read the information of a compression algorithm (its version for instance): Click About, and a dialog box will pop up showing the related information. The dialog box will be different according to the compressor you select.

g. To modify the audio compression settings, click Audio Compression Setting to open the AVI Audio Compression Setting window. Select the desired audio quality, format, and attributes in the corresponding fields.

If you do not choose to compress the video, the generated AVI file will be very large.


102 - User's Manual

Record an EXE/3GP/AVI File

Please follow the steps below to record an EXE/3GP/AVI file of a live video stream:a. Select a video cell or a device from the heirarchical management tree which you want to record to

media file.b. Click Record to EXE/3GP/AVI on the quick access bar, or right-click the video cell and click

Record to EXE/3GP/AVI. You can also click Edit > Record to EXE/3GP/AVI on the menu bar. (The UI string will change according to your Recording Settings.)

c. For recording a high-resolution video (1600 x 1200) in AVI type, a dialog box will pop up as shown below to remind you that the CPU loading will increase. Click OK to continue the process.

d. The icon will then change to Recording EXE/3GP/AVI , and a red text string (EXE/3GP/AVI) will appear at the bottom right of the video cell. Note that only one video channel can be recorded at a time.

e. When you want to terminate the AVI Recording, click the icon on the Quick Access Bar. The export process will then terminate and the button will change from to . The recorded media files will be found in the preset storage folder on your local computer as shown below.

Below is the file name format for AVI files:

AVI

20100125_173015.avi

Date and time (YYYYMMDD_hhmmss)

Video format


User's Manual - 103

Built-in Media Player--EXE

The following is the icon of EXE. Double-click it, the recorded video will be played automatically as shown below.


Pause Pause playback of the focused video clip

Play Start playback of the focused video clip

Stop Stop playback of the focused video clip

Next Frame Go to the next video frame of the focused video clip

Slow Down Slow down the playback rate

Speed Up Speed up the playback rate

Control Buttons

Timeline Slider

Status Panel

Current time of the video clip

Total length of the histogram

The playing rate can be 1/8, 1/4, 1/2, 1X, 2X, 4X, 8X, 16X, 32X, and 64X.

Video Title


104 - User's Manual

The function menu of the built-in media player are displayed as shown below:

The built-in player is able to playback 3GP and EXE files. The built-in player is able to save 3GP files as EXE files. The built-in player is able to save EXE files as 3GP files. The built-in player is able to convert EXE and 3GP files into AVI files. The built-in player also supports snapshot and print functions.


User's Manual - 105

View Settings

This section allows you to set the display mode of a video cell, including Display Location, Date and time Format, Video Display Mode, and Font Settings. When you change the settings, the sample window will change accordingly for you to preview the settings.

Display Location

As the illustration shows, there are 4 display areas for you to input information about the live video. Each drop-down list includes 6 options for you to select: No display, Camera Name, Video Title, Camera Date, Camera Time, and Camera DateTime.

Display Area 1 Display Area 2

Display Area 3 Display Area 4


106 - User's Manual

Date and Time Format

Same as local computer: Select this option and then the date and time format will synchronize with the local computer.

Specify: Select a desired format for the date and time from the drop-down list. Date format: Select YYYY/MM/DD or MM/DD/YY. Time format: Select the default time format (synchronize with the local computer), 12h AM/PM, or 24h.

Video Display Mode

Show motion window when triggered: If you select this option, the red frame of the motion detection window will appear in the video window when motion is triggered. This function is enabled as default.

For detailed information about how to set up the layout of the live view window, please refer to How to Change Video Viewing Mode on page 34.

Font Settings

This function allows you to change the font on the video cell.

Font: Automatically lists all fonts installed on your operating system. Select the desired type.

Color: Select a desired font color (white, red, green, blue).

Size: Select a desired font size (8, 10, 12, 14).

Keep the aspect ratio: In the default settings, the size of the video window will change according to the layout of the live view window you choose. However, the frame size may be distorted. If you select Keep the aspect ratio, the video window will be adjusted to the same frame size as the preview window. This function is disabled as default.


User's Manual - 107

General Settings

This section allows you to configure the System Settings and Rotation Settings.

Event Settings

Enable live event notification: Select this option to activate real-time event notification. For example: the event notification of DI/O status on the hierarchical management tree, the event list in the event window, motion detection windows in video window, or the event notification on E-map settings page, etc. This function is enabled as default.

Enable alert sound(s): If you enable this option, you will hear alert sound on the client side when the event is triggered..

Event window mode: Select Fixed or Popup mode for the event window. For more information about event window, please refer to page 18.

Rotation Settings

Enable rotation after login: If you check this option, the video cells will start to rotate after you login to the ST7501 LiveClient. The default setting of this function is disabled.

Rotate the page every second(s): Fill in a desire interval time for video page rotation. The maximum value is 99 seconds. The default value is set at 6 seconds.

For detailed information about how to set up the layout of the monitoring window and rotation functions, please refer to How to Change Video Viewing Mode on page 34.

Display Settings

Enable de-interlace function: Select this option if your connected device does not support de-interlace function. For example: VS7100.

System Settings

Auto login after logging in to operating system: If you check this option, ST7501 LiveClient will automatically login after you login to Windows without entering the user name and password. The default setting of this function is disabled.

Automatically display in full screen after login: If you check this option, the video cells will be displayed in full screen without showing the menu bar or the control panels.

Auto add newly-inserted camera to video cell: If you check this option, ST7501 LiveClient will automatically add the newly-inserted device to a video cell. This function is enabled as default.

Retrieve RTSP streaming on specific port: The default port for RTSP streaming is 554. If you want to change this port, please check this item and fill in a desired port.


108 - User's Manual

Joystick Settings

This section explains how to remote control connected network devices with a USB joystick. It’s easy to install and configure via the USB interface.

Enable JoystickConnect the USB plug of the joystick to a USB port on your computer. Supported by the plug-in in the main page (Microsoft’s DirectX), once the plug-in in the main page is loaded, it will automatically detect if there is any joystick on the computer. The joystick should work properly without installing any other driver or software.

Then you can begin to configure the joystick settings of linked devices. Please follow the instruction below to enable joystick settings.a. Click Configuration > Client Settings > Joystick Settings on the menu bar to open the Joystick

Settings window. If your joystick is working properly, it will be displayed on the drop-down list. b. Select the joystick you want to configure. Check Enable Joystick, then click Configure Buttons to

open Buttons configuration window.

a

b


User's Manual - 109

Buttons ConfigurationIn Buttons Configuration window, the left column shows the actions you can assign, and the right column shows the functional buttons and assigned actions. The number of buttons may differ from different joysticks. Please follow the steps below to configure your joystick buttons:a. Choosing one of the actions and click Assign will pop up a dialog. Then you can assign this action to

a button by pressing the joystick button or select it from the drop-down list. For example: Assign Home (move to home position) to Button 1.

b. Click OK to confirm the configuration.


110 - User's Manual

c. The Assigned Action will appear beside Button 1 in the right column as shown in the following diagram. Note that a button can only be assigned with an action. If you want to modify the settings, select the action on the list and click Clear Selected.

d. If you want to assign additional actions, repeat step a.~c. When all settings are complete, click OK to save the settings or click Cancel to discard the settings.


User's Manual - 111

e. Click OK to save the settings or click Cancel to discard the settings.

If you want to assign Preset actions to your joystick, the preset locations should be set up in advance.

If your joystick is not working properly, it may need to be calibrated. Click Calibrate to open the Game Controllers window located in the MS Windows control panel and follow the instructions for trouble shooting. For more information, please refer to the MS Windows help files for details.

The joystick will appear in the Game Controllers list in the Windows Control Panel on your computer. If you want to check out your device, go to the following page: Open Start > Control Panel > Game Controllers.


112 - User's Manual

PTZ/ E-PTZ FunctionIn addition to using the PTZ control panel, you may also control the rotation handle of the joystick to remote control a PTZ/ E-PTZ network camera with ease.

Pan/Tilt: Move the rotation handle of the joystick; you can pan the camera to the desire position. There will be blue line displaying the moving direction in the center of the video image as the diagram 1 below.

Zoom in/Zoom out: Shift the rotation handle clockwise to zoom in the camera on an image or go counterclockwise to zoom out the camera on an image. There will be a circle and four vectors in the center of the video image as the diagram 2, 3 below.

Proxy SettingsIn this section, you can enable, modify, or cancel Proxy Settings for client if your ST7501 Server is under a proxy. If you change the proxy settings, please please fill in the new value next time you login the LiveClient next time.

Zoom in(Turn the rotating handle clockwise)

Zoom out(Turn the rotating handle counter-clockwise)

Pan/Tilt(Move the rotating handle back and forth)


User's Manual - 113

How to Search for a Device on the Device Tree

This function allows you to conveniently search for an inserted device, which is useful when many devices have been inserted.Please follow the steps below to find a device on the camera list:a. Click the station on the device tree.b. Click Edit > Find on the menu bar (or right-click the station and click Find).

c. The Find window will pop up for you to set your search criteria. Find what: Enter a string in the blank. The string can be the full or partial name of the device you

want to search for. String Options: Match case represents that the search results should be identical to the string in

lower-case or upper-case letters, the string can be part of a word. Match whole word means that the search results should be identical to the string for every character, and that the string should be a complete word or phrase. If you select both options, the search results should conform to all criteria listed above.

Direction: Select search up or search down.

d. Click Find Next, the seaching result will be marked as shown below.

e. If there is nothing found in the camera list, a message will pop up as shown below:

Search upSearch down

b

c

Search resultsd

b

a


114 - User's Manual

How to Print a Video Image

There are two ways to print out an image of live video:1. Select a video cell, then click Print on the quick access bar, or right-click the video cell and select

Print from the popup menu. A Print window will pop up for you to choose the printer.

2. You can also click Edit > Print to print out an image from a video. Focus Cell: Print out an image of the target video. All Cells: Print out an image with all video cells in the monitoring window.

How to Lock ST7501 LiveClient for Security Concerns

If you are away from your computer, for security reasons, we suggest you lock the program. When LiveClient is locked, the user must fill in the correct password to unlock and access the program again. To lock LiveClient, click Unlock on the quick access bar or click System > Lock on the system

menu. The Unlock icon will then turn into Lock . To unlock LiveClient, fill in the correct password in the popup window.


User's Manual - 115

How to Log out from the ST7501 Server

To logout from the current server, click Logout on the quick access bar or click System > Logout on the menu bar. A confirmation window will pop up. Click OK to confirm or Cancel to return to the ST7501 LiveClient window.

How to Exit ST7501 LiveClient

To exit ST7501 LiveClient, click Exit on the quick access bar or click System > Exit on the menu bar. A confirmation window will pop up. Click OK to confirm or Cancel to return to the ST7501 LiveClient window. When you exit the program, your user account will be automatically logged out from the current server.


116 - User's Manual

ST7501 Playback ConfigurationActivating ST7501 Playback and Logging in to a Server

ST7501 Playback allows you to search and playback recorded media data from ST7501 Server. Once you insert a device into the device tree of ST7501 LiveClient, it will automatically be displayed on the device tree of ST7501 Playback. You can then begin to use ST7501 Playback to view recorded or backup video clips.After installing the ST7501 Playback program, please follow the steps below to activate ST7501 Playback:1. Run the ST7501 Playback program. If you have already run ST7501 LiveClient, you can also click

System > Launch Playback to activate ST7501 Playback.2. A Login window will pop up. Fill in the information as shown below: If you want to login to a remote ST7501 Server, enter the IP address, user name, password and

communication port of the server. Click Log in to login the target server or Cancel to exit the system.

If you want to login to your local host which is running ST7501 Server, check the Login local station checkbox, and the local IP Address will be displayed automatically. Enter the User Name, Password, and Communication Port of the local server to log in. Click Login to log in to the target server or Cancel to exit the system.

3. The ST7501 Playback main window will be displayed.

If your network environment need to set up proxy, click More >> to extend the login window, then click Proxy Setting to open the dialog. Then enter related information to link to your proxy server.

Available functions of the ST7501 Playback program will be enabled according to the role of your login account. For more details about the privileges of the user account, please refer to How to Manage User Accounts on page 41.


User's Manual - 117

ST7501 Playback User Interface

A. Menu bar B. Quick access bar C. Query panel (Browsing / Time search / Event search / Log viewer) D. Status panel E. Recorded video playback window F. Playback control panel G. Video clips list

Menu Bar

Status Panel

Menu Item Drop-down Options

System Lock / Language / Launch LiveClient / Logout / Exit

Edit Snapshot / Print / Find

View Backup Status /Exporting Status / Time Search / Event Search / Log Viewer / Full Screen / Minimize

Configuration Client Settings (Snapshot Settings / Export Settings / View Settings / Proxy Settings / General Settings)

Layout Change Layout

Help About


G

D

A

E

B

C

F


118 - User's Manual

Quick Access Bar

Some buttons will be disabled if the selected device does not support those functions.

Recorded Video Playback Window

The "VIVOTEK" logo indicates that no camera has been assigned to the video cell.


Exit Exit the system

Logout Logout from the current station

Lock Click to Lock the system for security concerns ( Unclock the system)

Volume Adjust the audio volume of the target video ( Mute)

Snapshot Capture the picture of the target video

Print Print out the picture of the target video

Remove All Connections Remove all live videos from the live video monitoring window

Layout Change the layout of video monitoring window

Full Screen Maximize the live video monitoring window

Switch Screen Switch to another screen

The red frame ( ) represents the focused cell.

Video Cell


User's Manual - 119

Language Selection

ST7501 current supports user interfaces in multiple languages; and language options are availabe in: English, Deutsch, Español, Français, Italiano, 日本語, Português, 簡体中文, and 繁體中文. If you want to select another language for the interface, please click System > Language on the menu bar to select a desired language. Please note that if you want to change the language option, a message will remind you to restart the system.

Query Panel-- Browsing Page

Dates with recorded video clips

Devices listed under the root station

If you want to use "User Defined" language, please prepare images and language strings, and upload the files to the following folders:

...\ST7501\Client\Playback\language\zz_UD (language string)

...\ST7501\Client\Playback\image (images)

Root Station Name (IP address)

Icon Description

Station list including server and local database

A station (a computer that has installed ST7501 Server)

The camera that exists on the device tree of LiveClient.

The camera that has been removed from the device tree of LiveClient (off-line). However, its recorded video (if any) is still accessible from the server.

Dates with recorded video clips.

Local database for backup data. For more information about how to upload backup data to the list, please refer to page 135.


120 - User's Manual

Query Panel--Time Search Page

The Time Zone is the same as your local computer.

Select station/ device(s) that you want to search for recorded files

Specify search period of time

Click to start to search, the results will be shown on the video clips list


User's Manual - 121

Query Panel--Event Search Page

Select an Event Category


Click to start to search, the results will be shown on the video clips list

Click to add search criteria

Click to remove search criteria

Select station/ device(s) that you want to search for recorded files


122 - User's Manual

Query Panel--Log Viewer Page

Select a Log Category

Select a User Account

Select a Result Type

Select a Log Type

Select a Log Level


Click to start to search, the results will be listed on the video clips list

Select station(s) that you want to search for recorded logs


User's Manual - 123

Video Clips List Window

If you select a option “date”, the video clips will be displayed in the video clips list window. A option “date” may contain more than one video clip.


124 - User's Manual

Playback Control Panel

When you double-click a video clip to play, the playback control panel will be enabled for you to use.


Histogram Zoom In Zoom in on the displayed period of time of the histogram

Histogram Zoom Out Zoom out of the displayed period of time of the histogram

Marker IIf you want to export part of the recorded video clip, click to set marker I on the histogram, which will be the start time of the exported media

Marker IIIf you want to export part of the recorded video clip, click to set marker II on the histogram, which will be the end time of the exported media

Export Media Click to export the marked video clip

Last Time Interval Go to the previous video clip on the video clips list

Pause Pause playback the selected video clip

Play Start to playback the selected video clip

Stop Stop to playback the selected video clip

Next Frame Go to the next video frame of the selected video clip

Next Time Interval Go to the next video clip on the video clips list

Repeat Mode Playback the selected video clip repeatly

Slow Down Slow down the playback rate

Speed Up Speed up the playback rate

Playback Timeline Slider

Playback Status PanelPlayback Control Buttons

Playback Histogram(Displays the period of time of the video clip being played back)

Current time of the video clipTotal length of the histogram

The playback status (Stop/Playing)

The playing rate can be 1/8, 1/4, 1/2, 1X, 2X, 4X, 8X, 16X, 32X, and 64X.


User's Manual - 125

How to Playback Recorded Video

Select a Recorded Video Clip

Please follow the steps below to select a video clip:1. On the Bowsing page, click the plus sign (+) to expand the device tree.

2. Right-click a station, device, or option “date” on the device tree and click Refresh to display the recorded video clips.

3. There are two ways to view the video clips of a date. View all video clips of a date:

a. Select a option “date” from the device tree.b. Double-click the option “date” or right-click the option “date” and click play, and it will start to

play in an available video cell. (You can also directly drag-and-drop the option “date” to a desired video cell in the recorded video playback window. The video clip will start to play.)

a bb


126 - User's Manual

View only one of the video clips of a date:a. Click a option “date” on the device tree. The corresponding recorded video clips will be listed in

the video clip list window.b. Select a video clip from the video clip list window.c. Double-click the video clip, then it will start to play in an available video cell. (You can also directly

drag-and-drop the video clip to a desired video cell in the recorded video playback window. The video clip will start to play.)

4. Then you can make use of the playback control panel to playback the selected video clip. Please refer to Playback Control Panel on page 124.

a

b

c


User's Manual - 127

Remove Recorded Video Clips from Video Cells

There are two ways to remove a recorded video clip from the video cell: 1. Right-click the video cell and select Remove.

2. Drag-and-drop the live view from the video cell to the device tree window.

If you want to remove all live videos from the video cells, please click on the menu bar.

Timeline Slider Bar and Histogram

The red part of the histogram shows the period of time of a video clip. The timeline slider bar will move forward as the video is on playback. You can manually move forward/backward the Timeline Slider Bar to the desired position as shown below.

The current time of the video clip will be displayed on the status panel. It will change according to the current position of the timeline slider bar.

Start time of the histogram End time of the histogram


128 - User's Manual

Zoom in / out of the Histogram

As the second picture shows, by clicking Histogram Zoom In, the total time of the histogram will shorten to half of the original period of time, while the red part of the histogram that shows the period of time of the video clip will extend to twice the original time span.

In addition to clicking and to zoom in/ out of the histogram, you can use the mouse directly to drag the histogram to zoom in part of the focused video clip.For example:a. Drag a section of the histogram. You can drag it to either direction.

b. The section will be extended as shown below.

For more functions of the playback control buttons, please refer to page 124 for detailed description.

Histogram zoom in

Histogram zoom out

Total time length


User's Manual - 129

Audio Control

The audio function will be enabled if the device is equipped with an internal or external microphone. Please follow the steps below to adjust the volume or turn on/off the audio of the focused video: To turn off the audio (Mute Mode)

a. Click Audio On on the quick access bar and check Mute. Or you can right-click on the video cell to open the popup menu, then click Others > Mute. The mute option in the popup menu will then be selected.

b. If you want to turn off the audio of all live video, select Apply all. c. The Audio icon will then change from to .

To adjust the audio volumea. Click Audio On on the quick access bar.b. Drag-and-drop the slider bar. Slide to a higher position for louder volume.

To turn on the audioa. Click Mute on the quick access bar and uncheck Mute. Or you can right-click on the video cell

to open the popup menu, then click Others > Mute. The mute option in the popup menu will then be unchecked.

b. If you want to turn on the audio of all live video, select Apply all. c. The Audio icon will then change from to .

a b

ab


130 - User's Manual

How to Change the Playback Layout

Changing the Layout of the Recorded Video Playback Window

VIVOTEK ST7501 Playback supports up to 16-CH simultaneous recorded video playback on a single monitor and allows you to change the layout of the recorded live video playback window based on the number of inserted devices.

Switch Video Channels

Drag-and-drop a video channel to another empty video window.

To switch two channels, drag-and-drop one view to the other, then the two channels will switch positions.

Configure Layout Mode

Click the Layout button on the quick access bar or click Layout > Change Layout on the menu bar. Select a desired layout mode and the layout window will change accordingly. Below we illustrate 6 types of layout modes:

Layout mode Description

1 x 1

2 x 2

1 + 53 x 3

1 + 124 x 4


User's Manual - 131

Maximize/Minimize the Recorded Video Playback Window

Single View: to maxmize a video cell to the entire video playback window

Double-click the video cell, or right-click the video cell and selec Single View. The focused video will occupy the entire Playback window as shown below.

To restore to the original layout, double-click the video cell or right-click the video cell and uncheck Single View.


132 - User's Manual

Full Screen: to maxmize the video playback window to the entire screen

Click Full Screen on the quick access bar or right-click the video cell and select Full Screen. In addition, you can also click View > Full Screen on the menu bar to maximize the recorded video playback window.

To restore to the original layout, right-click the video cell and uncheck Full Screen. You also can press the Esc button on the keyboard to leave the full screen mode.

Minimize: If you click View > Minimize on the menu bar, the Playback window will minimize to the Windows tool bar.

View Recorded Video with Multiple Monitors

If you have multiple screens in your control center, you can switch the ST7501 Playback Window among these screens.

If you have two monitors, click Switch Screen on the menu bar, the Playback window of monitor 1 will switch to monitor 2.

If you have three or more monitors, a drop-down list will be displayed when you click Switch Screen on the menu bar. The number of items on this list depends on the number of your screens. Select

a desired screen from the drop-down list and the Playback Window will then switch to the specified screen.

Monitor 1 Monitor 2

Monitor 1Monitor 2Monitor 3 ......


User's Manual - 133

How to Backup Recorded Video

In addition to the Schedule Backup function of ST7501 LiveClient introduced on page 61, the ST7501 Playback also features to backup recorded video clips from the local database. Please open the Browsing page and follow the steps below to backup recorded video:a. Select the target files. To backup all recorded video of a selected device: Right-click the device and click Backup.

To backup all recorded video of the day: Right-click the option “date” and click Backup (or select the date and click the Backup button below).


134 - User's Manual

To backup part of the recorded video of the day: Select the date and choose the video clip(s) from video clip window. Then right-click the selected option(s) and click Backup. Note: Press Shift on your keyboard, then you can select more than one video clips.

b. A Backup Settings window will pop up. Specify the time span and select a storage path, then click Backup. The system will start to backup and popup a window showing the backup status.

If you close the status window, you can also open it again by clicking View > Backup Status.

d. When the backup is complete, you will see an information dialog. The recorded data will be restored in the specific folder.


User's Manual - 135

How to View Backup Files

The ST7501 Playback also allows users to playback backup files, including Schedule Backup by ST7501 LiveClient and Recorded Data Backup by ST7501 Playback.

Please follow the steps below to view backup files:a. Right-click Local DB and click Add.b. A Load Backup File window will pop up as shown below. Select the *.dif file to upload.

c. The following is an example of uploaded file, and you can double-click it or drag-and-drop it to a video cell to playback.

ab


136 - User's Manual

If you want to playback the backup files from the local database, you can also click Working Offline in the Login Window without the account information. The ST7501 Playback will launch as shown below.

You can upload backup files

No user account information required


User's Manual - 137

How to Search for a Video Clip in a Specific Period of time

Please follow the steps below to use Time Search function:a. Open the Time Search page.

b. Select the target station(s)/device(s) that you want to search for video clips.c. Specify the time span. You can choose to set up the start time only, the end time only, or both the

start time and end time. The search results will only include the video clips within the time span. If you uncheck both the start time and end time, the search results will include all video clips recorded by the selected device(s).

d. Click Search to start time search.e. View the retrieved video clips.

a

c ed

b

Click here to move the focus to the current date

Click to select a yearClick to select a month from the drop-down list

You can manually enter a specific time.


138 - User's Manual

How to Search for Events

The ST7501 Playback program offers users an intuitive event search engine for retrieving video clips from the database of recorded videos based on different search criteria such as motion, IVA, or DI events. Please follow the steps below to search for recorded events:a. Open the Event Search page.

b. Select the target station(s)/device(s) that you want to search for events.c. Specify the Event Category. For detailed information, please refer to Select Event Category on the

next page.d. Specify the time span for event search. You can choose to set up the start time only, the end time

only, or both the start time and end time. The search results will only include the events within the time span. If you uncheck both the start time and end time, the search results will include all events from the selected device(s). Please refer to step c. on the last page for detailed information.

e. Start event search. Please refer to page 142 for detailed information.f. View the retrieved video clips. Double-click it or drag-and-drop it to the video cell. It will playback in

repeat mode. Note: The length of each video clip will depend on your settings of pre-event time & post-event time for

the recording storage. The default setting is 20 seconds. For more infromation, please refer to page 58 for detailed illustration.

b

c

d

e

f

a

repeat mode


User's Manual - 139

Select Event Category

The following introduces the event search categories: All Events, All Motion Events, All IVA events, All DI Events, Named DI Events, PIR, Tampering, and Tamperature. You can also add or remove customized events from the list.

Event Category- All Events

If you select the All Events category, all of the events including motion detection, digital input, and intelligent video analysis, PIR, tamper detection, and tamperature alarm will be listed in the search results. You can click Add or Remove to change the search criteria options.

Event Category- All Motion Events

If you select the All Motion Events category, all detected motion events will be included in the search. You can click Add or Remove to change the search criteria options.

The parameters of the motion detection windows, such as motion percentage and the time of occurrence are also recorded in the database of the server. If you want to change the parameters of the motion detection windows such as the position, size, detection sensibility, and motion percentage, please link to the camera's Configuration page to modify the values.

Video(TCP-AV) 2010/08/03 16:00:20


140 - User's Manual

Event Category- All IVA events

If you select the All IVA events category, all detected IVA events will be included in the search. Cameras with embedded intelligent video content analysis are capable of detecting IVA events such as moving objects, loitering, and tamper detection. The embedded video content analysis, superior to the conventional motion detection function, is capable of distinguishing between creature’s motions and still backgrounds or natural movements such swaying trees, waves or sunsets so as to prevent false alarms from environmental noise. With camera tamper detection, it can detect incidents such as camera redirection, blocking or defocusing of cameras, or even spray-paint. Additionally, a suspicious object in the predefined detection region will trigger alarms once the dwell time of the object is longer than the given time. You can click Add or Remove to change the search criteria items.

If you want to change the parameters of IVA, such as the detection region, loitering duration, etc, please link to the camera's Configuration page to modify the values.

Event Category- All DI Events

If you select All DI Events category, all triggered DI signals will be included in the search. The DI events signify that there is a Digital-Input signal detected by the camera; its corresponding information such as DI-Trigger or DI-Normal signal and the time of occurrence are also transmitted and recorded in the database of the server. You can click Add or Remove to change the search criteria options.

For more information about DI/DO settings on the connected devices, please refer to page 46 for detailed illustration.


User's Manual - 141

Event Category- Named DI Events

This category allows you to select only Named DI Events--the DI device which you have renamed in the LiveClient. Please refer to Association Management on page 46 for more information about how to rename DI device.Click OK and fill in the name you want to search on the left window.

The new search criteria will be displayed in the search categories column as shown below.You can click Add or Remove to change the search criteria options.


142 - User's Manual

Start Event Search

After you specify all of the search criteria mentioned above, check/uncheck Display in new result list and click Search to begin event search. If Display in new result list is unchecked, all search results will be displayed on the original event list

window as shown below.

In the above picture, The Type field in the search result page shows the event category, and the Description field displays the motion percentage of the detection window. Please refer to page 139 for more inforamtion about Motion Events.

If you select Display in new result list and click Search, the search results will be displayed on a new page as shown below. This allows you to place the search results of each search category on an individual page. You can set up to 5 pages in the event list window.

Unchecked Only one page

Checked You can set up to 5 pages.


User's Manual - 143

Backup the Event Videos

Please follow the steps below to backup the evnet videos on the results list:a. Select the video clips you want to backup. You can select more than one video clips.b. Right-click the selected video clips and click Backup.

c. A Backup Settings window will pop up. For more information about how to set up the Backup Settings, please refer to page 133. For more information about how to view backup files, please refer to page 135 for detailed illustration.

a

b


144 - User's Manual

How to Search Logs

The ST7501 Playback program offers a convenient log engine for searching all local logs based on different search criteria such as log category, log type, and log level. The search results will be displayed in the log viewer window along with the detailed log history.

Please follow the steps below to search logs:a. Open the Log Viewer page.b. Select the target station where you want to search logs.c. Specify the Log Category. For detailed information, please refer to Select Log Category on page 145.d. Specify the User Account. If you have added other user accounts to the station, you can select one to

search its login history. For detailed information about user account, please refer to How to Manage User Accounts on page 41.

e. Specify the Search Result. Select All to display all search results; select Success to display successful log activities only; select Fail to display failed log activities only.

f. Specify the Log Type. For detailed information, please refer to Select Log Type on page 145.g. Specify the Log Level. For detailed information, please refer to Select Log Level on page 145.h. Specify the search time span. You can check the start time only, the end time only, or both the start

time and end time. The search will only include the events within the time span. If you uncheck both the start time and end time, the search will include all events saved by the server. Please refer to page 137 for detailed information.

i. Start the log search and the results will be displayed on the log list window.

a

b

c

h

ed

i

i

f g


User's Manual - 145

Select Log Category/Log Type/Log Level

The following table shows the breakdown of log category, level, and type. The search results will be different according to your selections.Log Categories Log Levels Log Types

Operation Log

Normal

Login / LogoutInsert UserUpdate User NameUpdate User PasswordUpdate User PrivilegeDelete UserInsert CameraUpdate Camera InformationDelete CameraSet Recording GroupInsert Recording Schedule / Update Recording Schedule / Delete Recording ScheduleInsert Event Management / Update Event Management / Delete Event ManagementInsert Recording Group / Update Recording Group / Delete Recording GroupInsert Recording Path / Update Recording Path / Delete Recording PathInsert Camera to the Recording GroupUpdate Camera information in the Recording GroupDelete Camera from the Recording GroupMove Recording PathMove Camera to another Recording GroupInsert Layout / Update Layout / Delete LayoutSet Digital OutputUpdate Scheduled Backup Update Server Port Set Proxy ServerSet UPNPSet DDNS ServerCreate Directory / Rename Directory / Delete Directory Insert SMTP Server / Update SMTP Server / Delete SMTP ServerInsert Network Storage Device / Update Network Storage Device / Delete Network Storage DeviceSet GSM ModemSet DI/DO RenameSet Relay Settings

High Manually Begin RecordingManually Stop Recording

LowCamera PTZ, Iris, Focus, Pan, Patrol ControlClick on ImageSelect Preset Location

System Log HighServer Start / Server StopVirtual Memory LowNetwork Lost

Event Log High

Camera Disconnected from the Server / Camera Connected to the ServerParent Station Connection Lost / Parent Station Connection RestoreCamera Recording Start / Camera Recording Stop Start Scheduled Backup / Stop Scheduled BackupEvent Trigger


146 - User's Manual

Search All Local Logs

Search Login History

Select Login History from the log category field and click the Search button below, the search results, including all login logs, will be displayed on the Login History page.

Log LevelLog Category

Log Type

Click to remove all search results from the listClick to export all search results from the list


User's Manual - 147

Search Login Activities

This function allows you to search the operations the user performed during the login period of time. You can search for login activities on the Local Logs or Login History page.

Search Login Activities on the Local Logs page:a. Click on the Local Logs page.b. Select a login/logout option from the list.c. Click Trace Login Activities (or you can right-click the selected login/logout option on the list, then

click Trace Login Activities).

d. The search results of the login activities will be displayed on the Login Activities page as shown below.

Search Login Activities on the Login History page:a. Click on the Login History page.b. Select a login/logout option from the list.c. Click Trace Login Activities (or you can right-click the selected login/logout item on the list and

click Trace Login Activities).

a

b

c

c

a

b

c

c


148 - User's Manual

d. The search results of the login activities will be displayed on the Login Activities page as shown below.

When you select All in the Log Level field, the search results will include all log levels. If you select Low in the Log Level field and select Including above level as shown in the picture on the left below, the search results will include all levels of logs. But if you select Normal in the Log Level field and select Including above level as shown in the picture on the right below, the search results will only include Normal-level and High-level logs.


User's Manual - 149

How to Configure Client SettingsOn Client Settings, you can configure Snapshot Settings, Export Settings, View Settings, Proxy Settings, and General Settings. It allows you to save snapshots and media files on the local computer.

Snapshot Settings

When you play a recorded video, ST7501 Playback also allows you to take snapshots. For detailed information about Snapshot Settings, please refer to page 97.

Export Settings

When you playback a recorded video, the ST7501 server allows you to export part of the recorded video in EXE, 3GP, or AVI format to your local computer. Before exporting a media file, please set up Export Settings first. For detailed information about how to set up EXE, 3GP, and AVI Export Settings, please refer to Record Settings on page 99.


150 - User's Manual

Export an EXE/3GP/AVI File

Please follow the steps below to convert part of an EXE/3GP/AVI file of recorded video:a. Playback a video clip from which you want to export a media file.b. Set a period of time. Move the timeline slider bar to the desired start time and click Marker I . Move

the timeline slider bar to the desired end time and click Marker II .

c. Click Export EXE/3GP/AVI , the server will start to export the data and popup a window showing the exporting status. If you close the status window, you can also open it again by clicking View > Exporting Status.

d. When the backup is complete, you will see an information dialog. The exported data will be restored in the preset storage folder on your local computer (C:\Program Files\VIVOTEK Inc\ST7501\Client\Playback\Export).

a

b

c

d

c c


User's Manual - 151

View Settings

This section allows you to set up the display mode of video cell. For detailed information about View Settings, please refer to page 105.

Proxy Settings

Please refer to page 112 for detailed illustration.

General Settings

System Settings Retrieve RTSP streaming on specific port: The default port for RTSP streaming is 554. If you want to

change this port, please check this item and enter a desired port.

Display Settings Enable de-interlace function: Select this option if your connected device does not support de-interlace

function. For example: VS7100.

How to Search for a Device on the Device Tree

The Playback also allows allows you to conveniently search for an inserted device. Please refer to page 113 for detailed information.

How to Print a Video Image

The Playback also allows you print out an image of live video. Please refer to page 114 for detailed information.


152 - User's Manual

How to Lock ST7501 Playback for Security Concerns

If you happen to be away from your computer, for security reasons, we suggest you lock the program. When ST7501 Playback is locked, the user must enter the correct password to unlock and access the program again. To lock Playback, click Unlock on the quick access bar or click System > Lock on the system

menu. The Unlock icon will then turn into Lock . To unlock Playback, click and enter the correct password in the popup window.

How to Log out from the ST7501 Server

To log out from the current server, click the station and click Logout on the quick access bar or click System > Logout on the menu bar. You can also right-click the station and click Logout. A confirmation window will pop up. Click OK to confirm or Cancel to return to the ST7501 Playback window.

How to Exit ST7501 Playback

To exit ST7501 Playback, click Exit on the quick access bar or click System > Exit on the menu bar. A confirmation window will pop up. Click OK to confirm or Cancel to return to the ST7501 Playback window. When you exit the program, your user account will be automatically logged out from the current server.


User's Manual - 153

Import and Export Utility

ST7501 supports import and export utility for user to keep record of all server settings. You can use the export file to copy the configuration on another host.

Export UtilityPlease follow the steps below to export the server settings:a. Under Microsoft Windows, choose "Start > All Programs > VIVOTEK Inc > ST7501 > Tools >

Import-export Utility."

b. The Import/Export Utility window will pop up. Click Export and select a target folder. The system will start to export a .bin file.

Import Utility

Please follow the steps below to import the server settings:a. Under Microsoft Windows, choose "Start > All Programs > VIVOTEK Inc > ST7501 > Tools >

Import-export Utility."b. The Import/Export Utility window will pop up. Click Import and select the export file. The system will

start to import the file.


154 - User's Manual

ST7501 Service Control Tool

ST7501 service control tool is a tool for server control and for user to be aware of the ST7501 Server status. It starts up as Windows OS startup.Under Microsoft Windows, choose "Start > All Programs > VIVOTEK Inc > ST7501 > Tools > VNSServiceControl."

You may also find it in the system tray icon of the tool bar, which indicates that the service is running: It shows a disconnection icon when the service is stopped:

A menu for the service control tool will pop up when you right-click on the icon:

Here you can manually start, stop and restart the service.

User Manual Camara Vivotek ST7501

Documents

Transcript of User Manual Camara Vivotek ST7501