USER MANUAL 1080p, STARVIS4 1/2.8" 2.1Mega Pixel Sony STARVIS PS CMOS High definition 12-bit digital...

USER MANUAL

1080p, STARVIS

True WDR, Super Low Light

High Definition Fixed Camera

2

The lightning flash with an arrowhead symbol, within an equilateral

triangle is intended to alert the user to the presence of uninsulated

dangerous voltage within the product's enclosure that may be of

sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert

the user to the presence of important operating and maintenance

(servicing) instructions in the literature accompanying the appliance.

INFORMATION - This equipment has been tested and found to comply with limits for a

Class A digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in

which case the user will be required to correct the interference at his own expense.

WARNING - Changes or modifications not expressly approved by the

manufacturer could void the user’s authority to operate the equipment.

CAUTION : To prevent electric shock and risk of fire hazards:

Do NOT use power sources other than that specified.

Do NOT expose this appliance to rain or moisture.

This installation should be made by a qualified service person and should conform

to all local codes

3

1.Features --------------------------------- 4

2. Menu Construction

---------------------------------

5

3. Troubleshooting --------------------------------- 11

4. Dimensions & OSD board configurations

---------------------------------

12

5. Specifications

---------------------------------

16

Contents

4

■ 1/2.8" 2.1Mega Pixel Sony STARVIS PS CMOS

High definition 12-bit digital image signals offering 2M are obtained with high speed of 30

fps and with low power consumption.

■ High Resolution 1080p

This camera has realized high resolution of 1100TVL using the top-notch full digital image

processing, 12 Bit A/D serial signal processing and special algorithm technologies.

■ DNR (Digital Noise Reduction, 2D+3D)

The DNR technology eliminates noise thus generating a distinct and clear image.

This camera DNR function utilizes both an adaptive 2D filter reducing noise in the

brightness of the image and an adaptive 3D filter reducing caused by movement.

■ DAY&NIGHT with ICR

This camera has the Day&Night function which outputs the filter changing signal with

detecting the illumination condition.

■ True WDR

Brightness of IR and saturation phenomenon are automatically adjusted.

Multiple exposure real WDR(Wide Dynamic range) with 30fps

■ OSD (On Screen Display)

This camera supports the OSD function which is used with multi language. And so, the

camera can be controlled bye selecting text displayed on the monitor screen.

■ Privacy Mask Function (24 points(Box:14ea, Polygon:8ea))

Privacy masking allows for the 'blanking' of specific areas of a scene, where the

viewing or recording of images is prohibited or undesired.

The technology of this camera allows for the user defined setting of a four point

polygonal mask, which is overlaid onto the video signal output.

Features

☞ How to change mode from HD-SDI to EX-SDI.

Press “Up” button for 3 seconds and then press “Set” button.

If you want to change HD-SDI mode again, press “Down” button for 3seconds and

then press “Set” button.

5

All functions would be set by OSD menu.

The menu consists of the main menu and sub menu.

Sub menu is displayed when user press set key on each

menu, at which you see arrow.

Please hold the “SET” key for a while to enter OSD

menu.

1. LENS

Select lens type.

▶DC/MANUAL

2. EXPOSURE

This function can adjust the intensity of radiation

incoming to the camera.

Use the "▲" "▼""◀" "▶" "ⓔ" switch or Joystick to select

a menu item.

1) BRIGHTNESS (0~20)

Set the screen brightness

2) SHUTTER

Select shutter mode.

▶AUTO/INDOOR/FLICKER

- AUTO

The shutter speed will be operated automatically.

▶INDOOR/OUTDOOR/DEBLUR

INDOOR: Iris

OUTDOOR: Iris + Shutter

DEBLUR: SHUTTER: 1/240+AGC

- MANUAL

Select shutter speed you want

▶1/30(NT:1/30,PAL:1/25),1/60(NT:1/60,PAL:1/50),1/240,

1/500,1/1000,1//2000,1/4000,1/8000,1/16000,1/30000

Menu construction

6

-FLICKER

This will prevent possible screen distortion to a mismatch between the vertical sync

frequency and the blinking frequency of the lighting.

3) TCS INFO

This function can capture clear image when the object move

fast.

▶Off/Mode1~20

- SPEED: Show the Shutter speed value (1/120 ~ 1/1600)

- DAY/NIGHT: Show the DAY/NIGHT mode (AUTO~EXTERN)

- SMART IR: Show the SMART IR level value

- HLC: Show the HLC on,or off state

4)SENS--UP

Select “Digital Slow Shutter” level (OFF/ 2x, 4x, 8x, 16x, 32x)

5) AGC

Set “Auto gain control” value (1~20)

3. BACKLIGHT

The function is used to set the Back Light Compensation (BLC), High Light Compensation

(HLC) and Wide Dynamic Range (WDR).

▶OFF, WDR, HLC, BLC

1) BLC

BLC Area shows up on the screen

H- POS(0~20):Set the position of BLC area.

V- POS(0~20):Set the position of BLC area.

H- SIZE(0~20):Set the size of BLC area.

V- SIZE0~20): Set the size of BLC area.

OPTION DESCRIPTION

OFF

MODE1~5

MODE6~10

MODE11~15

MODE16~20

NOT USED

Shutter 1/120~6000 + DN EXT + Smart IR 14

Shutter 1/120~1600+ User DN + User Smart IR

Shutter 1/120~1600 + DN EXT + Smart IR 14 + HLC

Shutter 1/120~1600 + User DN + User Smart IR+ HLC

7

2) HLC

High Light Compensation

▶ON(0~20), OFF

LEVEL: Select HLC level.

MODE: Select mode

▶ALL DAY, NIGHT ONLY

3) WDR

Single scan Wide Dynamic Range that will be displayed

Half frame(PAL:12frame/NTSC:15grame)

WEIGHT:LOW/MIDDL/HIGH

4. DAY/NIGHT

The function is used to set the Day/Night function which switches day/Night mode

automatically based on the level of illumination.

1) AUTO

THRESHOLD(0~20): Set the threshold for identifying

the Night status from the Day status.

MARGIN(0~20): Set the margin for identifying the Night

status from the Day status.

DELAY: Sets the Night/Day identification transfer time.

SMART IR (0~20):

Brightness of IR and saturation phenomenon are automatically adjusted.

2) EXTERN

- EXTERN SW

Select the active level.

- DELAY (1~20)

Set the Night/Day identification transfer time

- SMART IR (1~20)

Brightness of IR and saturation phenomenon are

automatically adjusted.

3) COLOR: Only Color

4) B&W: Only B/W

5. WHITE BAL

This function is used to set the White Balance operation which adjusts the color scheme.

1) AUTO: Auto tracking white balance.

2) MANUAL

8

White balance value can be changed by “R-GAIN”,“B-GAIN” and “ KELVIN value in

manual mode

3) AUTO ext: TDN lens Auto trace white balance.

It can be changed in AWC mode only.

4) Preset: when the set color temperature doesn’t meet with user’s environment.

6. DNR

Set up 3D-DNR (Digital Noise Reduction) level.

▶OFF, LOW, MIDDLE, HIGH

7. IMAGE

1) SHARPNESS (1~10)

Select the resolution of the camera.

2) GAMMA (0.45, 0.5,0,55,0,6,0.65)

Select the GAMMA

3) COLOR GAIN (1~20)

Adjust COLOR GAIN

4) MIRROR (ON/OFF)

Set up the screen mirror

5) FLIP (ON/OFF)

Set up the screen flip

6) D-ZOOM (1X~16X)

Enlarge the screen with DIGITAL ZOOM.

7) ACE (OFF/LOW/MIDDLE/HIGH)

Select Digital ACE(Advanced Enhance) level

8) DEFOG (OFF/MANUAL/AUTO)

This function does a process of clearing blurred image

caused by fog and snow by analyzing the brightness of

input image and compensating the color of the image.

Select defog level.

9) SHARDING

Set the lens shading.

When you maximize zoom ratio and lens angle of view is saturated on screen, set to ON to make the lens edge invisible. It might happen only if fluorescent light is shined fully on screen.

10) PRIVACY

The function is used to configure up to 24 privacy masks, where the scene is prohibited or

undesired to be viewed.

9

ZONE NO (box 16ea+polygon 8ea): Select area using left

or right button.

ZONE DISP (ON/OFF): Show up PRIVACY AREA

function on the screen.

H-POS (0~60): H position.

V-POS (0~40): V position.

H-SIZE (0~40): H size.

V-SIZE (0~40): V size.

Y LEVEL(0~20): Adjust the Y LEVEL of the Privacy zone

area

CR LEVEL(0~20): Adjust the B GAIN of the Privacy zone area

CB LEVEL(0~20): Adjust the R GAIN of the Privacy zone area

8. MOTION

The function is used to configure the Motion Detection

operation and Alarm function which sense the

movement of the scene.

SENSITIVITY (0~10): Set the motion detection

sensitivity.

WINDOW TONE: Set window tone

WINDOW USE (0~3): Select motion areas you desire to set.

WINDOW ZONE: Select On or Off

DET H-POS(0~60): H position

DET V-POS(0~40): V position

DET H-SIZE(0~60): H size

DET V-SIZE(0~40): V size

9. OPTION

1) COM

Set camera ID and BAUDRATE for remote control.

This camera supports D-max and Pelco protocol.

In case of box camera can be used this function only.

10

2) IMAGE RANGE (Full, Comp, User)

Digital output data scale

3) OUTPUT MODE: Select output mode

4) FRAME RATE (2M: 1080-30p, 720-30p)

Set the frame rate

5) COLOR BAR

Select color bar to on or off

6) CVBS

Select input frequency to 50Hz OR 60Hz

7) CVBS

Select on or off

8) LANGUAGE

The function is used to select preferred one from the supported languages.

(English/Japanese/Chinese/Korea)

9) CAMTITLE

Camera TITLE display ON/OFF

Set Camera TITLE.(up to 8 characters)

A,B,C,D,E,F,G,H,I,J,K,L,M,N,O,P,Q,R,S,T,U,V,W,X,Y,Z,

0,1,2,3,4,5,6,7,8,9

10) VERSION

Camera VERSION display

10. Exit

SAVE: All the settings of the internal OSD menu are saved.

RESET: All the internal OSD menu settings are reset

11

If there are problems in operation, please refer to the items below. If the problem persists,

please contact the agent you purchased this product from.

Problems Troubleshooting

Nothing appears on the

screen.

• Please check the power connection.

• Please check the video signal line connection.

• Please check and make sure that the auto lens switch is

set to DC (VIDEO) when using a VIDEO(DC) lens.

The video image is not clear.

• Please check if the lens is clean.

Please clean the lens with a clean cloth or brush.

• Please adjust the contrast feature of the monitor.

• Please readjust the back focus of the camera.

The screen is dark.

• Please adjust the contrast feature of the monitor.

• If you have an intermediate device, set the 75 / Hi-z

properly, and check the terminals.

• Please check if an auto iris lens is being used and adjust

the brightness level.

There is a problem with the

camera operation.

• Please check if an appropriate power source to the

camera complies with the manufacturer's

standard requirement, or if the voltage keeps changing.

The MOTION DETECTION

function is not working.

• Please check if 'MOTION DETECTION' mode is turned

on.

• Please check if the MD LEVEL is too low.

• Please check the setting of the MD AREA.

Colors are not quite right. • Please check the 'WHITE BAL' setting

The screen is flickering.

• Please check if the camera is facing directly into sunlight

or fluorescent light.

• Please check if an auto iris lens is being used.

• Please check the connection of the lens connector cable.

COLOR mode is not working. • Please check if the AGC menu is set to the OFF

position.

SENS-UP function is not

working.

• Please check if the AGC menu is set to the OFF

position.

• Please check if the SHUTTER menu is set to

MANUAL mode.

4. TROUBLESHOOTING

12

1-1 BOX CAMERA(HD-SDI)

Dimensions & OSD Board Configuration

13

1.2 BOX CAMERA(AHD+TVI)

☞ Mounting bracket screw hole

Please use the screw hole when fixing the

camera onto the mounting bracket. Please use

the clamp screw as specified picture.

The mounting bracket can be separated and attached to the

top of the camera.

In this instance please do not tighten the screw to a depth of

more than 5mm,

otherwise serious damage can occur to the inside of the camera.

☞ DC Auto Iris Pin Configuration

Pin No. LENS

DC

No.1 Pin Damping-

No.2 Pin Damping+

No.3 Pin Drive+

No.4 Pin Drive-

14

2~3. DOME CAMERA

Dimensions OSD Board

4. VANDAL DOME CAMERA


15

5~6. IR DOME CAMERA (24IR)


7. IR VANDAL DOME CAMERA (30IR)


16

8. IR BULLET CAMERA (36IR)




,

17

10. IR HOUSING CAMERA (84IR)


18

1. BOX CAMERA

MODEL HD-SDI TVI AHD

Video

Image Sensor 1/2.8” 2Mega PS-Sony STARVIS CMOS

Scan mode Progressive Scan

Total number of pixels 1945(H) × 1109(V)

Number of active pixels 1945(H) x 1097 (V)

Resolution 1080P

Minimum illumination Color 0.03Lux / Min. 0.0001Lux with Sense-up(32x)

Video Output HD-SDI/Analog TVI/Analog AHD/Analog

S/N Ratio More than 50dB (AGC Off)

Lens

Mount CS Mount

Iris DC Iris

Function

Day & Night Auto / Color / BW / EXT

White Balance AUTO, AUTOext, PRESET,MANUAL

AGC Off/0 -20

DNR Off / Low / Middle / High

Mirror / Flip Off / On

Privacy Zone / Motion 24 Zones / 1 Zones

Brightness Level (1~20)

Shutter Auto/Manual(1/30~1/30000)

Back light HLC/WDR/BLC

Environment

Operating Humidity 30 % ~ 90 % RH

Operating Temp. - 10°C to 50°

Electrical

Power Consumption Max 3W

Power Supply DC12V±10,

Dual Type: AC24/DC12V(Optional)

TDN(Optional)

Mechanical

Construction Aluminum body

Dimension(LxWxH) 119.8X 67.9X64.7mm

7.9(W)X64.7(H)mm

104.7X 61X55mm

Weight About 0.42kg

Specifications

19

2. DOME CAMERA (Fixed Lens)


Video





Resolution 1080P




Lens

Lens 3.6mm Fixed Mega Pixel Lens

Iris Electric Iris

Function



AGC Off/0 -20







Environment



Electrical

Power Consumption Max 2.5W


Dual Type: AC24/DC12V(Optional) Mechanical

Construction Plastic body , PC bubble

Dimension 87mm(H) X 81Ø

Weight About 0.35kg

20

3. DOME CAMERA (Vari-focal Lens)


Video





Resolution 1080P




Lens

Lens 2.8~12mm Varifocal DC Mega Pixel Lens

Iris DC Iris

Function



AGC Off/0 -20







Environment



Electrical




Construction Plastic body , PC bubble


Weight About 0.35kg

21

4. VANDAL DOME CAMERA


Video





Resolution 1080P




Lens

Lens 2.8~12mm Varifocal Mega Pixel Lens

Iris DC Iris

Function



AGC Off/0 -20







Environment


Operating Temp. -30°C~60°C(-22°F~140°F)

Electrical




Construction Aluminum body , PC bubble

Dimension 145(W) x 118.5(H) mm

Weight About 1kg

22

5. IR DOME CAMERA (Fixed Lens)


Video





Resolution 1080P

Minimum illumination Color 0.03Lux / Min. 0.0001Lux with Sense-up(32x) /LED On:0Lux



Lens

Lens 3.6mm Varifocal Mega Pixel Lens

Iris Electric Iris

Function



AGC Off/0 -20







IR LED

LEDs 24 LEDs (850nm)

Visible Distance 15m

Environment



Electrical




Construction Plastic body ,PC bubble


Weight About 0.35Kg

23

6. IR VARIFOCAL DOME CAMERA (Vari-focal Lens)


Video





Resolution 1080P




Lens

Lens 2.8~12mm Varifocal DC Mega Pixel Lens

Iris DC Auto Iris

Function



AGC Off/0 -20







IR LED



Environment



Electrical




Construction Plastic body ,PC bubble


Weight About 0.35Kg

24

7. IR VANDAL DOME CAMERA (30IR)


Video





Resolution 1080P




Lens

Lens 2.8 ~ 12mm MP DC Auto Iris Lens

Iris DC Auto Iris

Function



AGC Off/0 -20







IR LED



Environment



Electrical




Construction Aluminum body ,PC bubble

Dimension 96(Bubble) x 118.5(H) mm

Weight About 1.1Kg

25



Video





Resolution 1080P




Lens


Iris DC Auto Iris

Function



AGC Off/0 -20







IR LED



Environment



Electrical




Construction Aluminum Body, Acrylic Window

Dimension 243.7mm(L) X 83.0mm(H) X 70.8 Ø

Weight About 0.9Kg

26



Video





Resolution 1080P




Lens


(Optional: 5~50mm DC Auto Lens) Iris DC Auto Iris

Function



AGC Off/0 -20







IR LED

LEDs 54LEDs (850nm)


Environment



Electrical




Construction Aluminum body, Acrylic Window

Dimension 100mm(H) X 117mm(W)

Weight About 1.5Kg

27



Video





Resolution 1080P




Lens


(Optional: 5~50mm DC Auto Lens) Iris DC Auto Iris

Function



AGC Off/0 -20







IR LED

LEDs 84LEDs (850nm)


Environment



Electrical




Construction Aluminum body, Acrylic Window

Dimension 138mm(W) X 106mm(H) X 311(L)mm

Weight About 1.5Kg

28

DISTRIBUTED BY

USER MANUAL 1080p, STARVIS4 1/2.8" 2.1Mega Pixel Sony STARVIS PS CMOS High definition 12-bit digital...

Documents

Transcript of USER MANUAL 1080p, STARVIS4 1/2.8" 2.1Mega Pixel Sony STARVIS PS CMOS High definition 12-bit digital...