USB BATTERY PACK USER GUIDE...Pack does not power the device 1.The device is drawing too much power....
1
PACKAGE CONTENTS • USB Battery Pack (CPBC5200AC Series) • User Guide SPECIFICATIONS Battery Capacity: 5200mA Rated Input: AC 100~240V, 50/60Hz 0.4A Rated Output: DC 5V 2.1A (Max.) PC Charging time: ~6 Hours Dimension: 4.26x2.2x0.96 inch Weight: 5.93 oz Environment: Storage: 14 to 122°F (-10 to 50°C) Operation: 32 to 104˚F (0 to 40˚C) SUGGESTED - PRIOR TO FIRST USE: It is recommended that you charge your CPBC5200AC Series battery pack for 10 hours to insure a full charge. CHARGING THE BATTERY PACK Charge the USB Battery Pack by putting the plug into an AC socket. When charging the battery pack, the LED indicator will light up automatically. Press the button to turn it off and press it again to switch the LED indicator on. Recharge the CPBC5200AC Series every 3 months when not in use to maintain peak battery performance. The battery capacity may decline after 300 charging cycles. SAFETY PRECAUTION Before using the USB Battery Pack, please read the following warnings carefully. Use the product according to the procedures described in this manual. Failure to follow these safety precautions may result in fire, explosion, electrical shock or other dangers 1. Store between 14 to 122°F (-10 to 50°C).Operate between 32 to 104°F(0 to 40°C). 2. Do not immerse this product in water or other liquids, as such use may result in fire or electrical shock. If water or other liquids enter the battery interior, unplug the product immediately from any attached power source or device. 3. Do not use this product with wet hands. Moisture in or on this product may result in electrical shock. 4. Store this product in a cool and dry environment when not in use. 5. Do not puncture this product. Puncturing the battery may cause the release of harmful substances. 6. It is normal for the USB Battery Pack to become warm during charging. 7. Ensure that all users read these warnings and instructions before using. 8. Please recycle USB Battery Pack in accordance with local environmental laws and regulations 9. Do not dismantle, open or shred secondary cells or batteries. 10. Do not expose cells or batteries to heat or fire. Avoid storage in direct sunlight. 11. Do not short-circuit a cell or a battery. Do not store cells or batteries haphazardly in a box or drawer where they may short-circuit each other or be short-circuited by other metal objects. 12. Do not remove a cell or battery from its original packaging until required for use. 13. Do not subject cells or batteries to mechanical shock. 14. In the event of a cell leaking, do not allow the liquid to come in contact with the skin or eyes. If contact has been made, wash the affected area with copious amounts of water and seek medical advice. 15. Do not use any charger other than that specifically provided for use with the equipment. 16. Observe the plus (+) and minus (–) marks on the cell, battery and equipment and ensure correct use. 17. Do not use any cell or battery which is not designed for use with the equipment. 18. Do not mix cells of different manufacture, capacity, size or type within a device. 19. Keep cells and batteries out of the reach of children. 20. Seek medical advice immediately if a cell or a battery has been swallowed. 21. Always purchase the correct cell or battery for the equipment. 22. Keep cells and batteries clean and dry. 23. Wipe the cell or battery terminals with a clean dry cloth if they become dirty. 24. Secondary cells and batteries need to be charged before use. Always use the correct charger and refer to the manufacturer’s instructions or equipment manual for proper charging instructions. 25. Do not leave a battery on prolonged charge when not in use. 26. After extended periods of storage, it may be necessary to charge and discharge the cells or batteries several times to obtain maximum performance. 27. Secondary cells and batteries give their best performance when they are operated at normal room temperature (20 °C ± 5 °C). 28. Retain the original product literature for future reference. 29. Use only the cell or battery in the application for which it was intended. 30. When possible, remove the battery from the equipment when not in use. 31. Dispose of properly. LEGAL NOTICES FCC Part 15 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. If the LED indicator extinguishes automatically during the charging process, press the button to revert. FCC WARNING Changes or modifications not expressly approved by the party responsible for compliance with the FCC Rules could void the user’s authority to operate this equipment. LIMITED PRODUCT WARRANTY CyberPower offers limited product warranty for the hardware of the USB Battery Pack* and the product is free from material and manufacturing defects for one year. A reasonable purchase proof with date must be provided when submission. CyberPower's sole responsibility is to repair or replace the product if a material or manufacturing defect results in product failure during its normal use. The warranty is void if the product is damaged due to abuse, alteration, misuse, negligence, incorrect voltage supply, air/water pollution, accidents and natural disasters. INTRODUCTION The USB Battery Pack (CPBC5200AC Series) is a high capacity rechargeable lithium battery designed for powering up to two mobile devices such as phones, MP3 players, tablets, and handheld gaming devices while away from other power sources FEATURES - Compact and portable design - Dual output - Built in AC plug - Battery life indicator PRODUCT VIEW: © 2013 CyberPower Systems, Inc. All rights reserved. Reproduction in whole or in part without permission is prohibited. USB BATTERY PACK USER GUIDE Model: CPBC5200AC Series TROUBLE SHOOTING K09-0000172-01 POWER YOUR DEVICES CHARGING THE POWER PACK PAD ITEM NO. DESCRIPTION 1 2 3 4 5 Power on/ LED Indicator Switch Power Off LED Battery Life lndicator USB Output Port 1* USB Output Port 2 AC Input Plug Press the button Press and hold for 3 seconds As the “LED INDICATOR” table showing 5V/ 2.1A (Max.) USB output AC 100~240V, 50/60Hz, 0.4A CONDITION NO. LED INDICATION 1 2 3 Battery Life Indicator Overload Low Battery Four LEDs represent 25%, 50%, 75% and 100% battery life from left to right side. All four LEDs flash simultaneously. The first LED light flashes rapidly. LED INDICATOR Problem Possible Cause Solution USB Battery Pack does not power the device 1.The device is drawing too much power. 2.The battery is out of power 3.The battery pack is overloaded. Check the power specification of the device before charging with the CPBC5200AC Series. Charge the battery pack. Remove the device causing the overload and press the power button to return to normal mode. Re-attach the USB connector to the socket. Check that power is provided USB Battery pack does not recharge 1.Incorrect connection between charger and USB Battery Pack. 2.No power from the source. *Charge tablets and Apple devices through USB Output Port 1 to achieve fast charging. 1 2 3 4 5 Note: 1. The LED indicator will automatically switch off 5 seconds after pressing the button. 2. When the battery pack is connected to the power, the LED indicator will light indicating the charging status. Press the button to switch off the indicator and press the button again to switch it back on. 3. All four LED indicators will flash when the battery pack is overloaded. Remove the device causing the overload and press the power button to return to normal mode. CyberPower Systems (USA), Inc. 4241 12th Avenue East, Suite 400, Shakopee, MN 55379, U.S.A. TEL: (952) 403-9500 Toll-Free: (877) 297-6937 FAX: (952) 403-0009 E-mail: [email protected] CPSww.com
Transcript of USB BATTERY PACK USER GUIDE...Pack does not power the device 1.The device is drawing too much power....
PACKAGE CONTENTS• USB Battery Pack (CPBC5200AC Series)• User Guide
SPECIFICATIONSBattery Capacity: 5200mARated Input: AC 100~240V, 50/60Hz 0.4ARated Output: DC 5V 2.1A (Max.)PC Charging time: ~6 HoursDimension: 4.26x2.2x0.96 inchWeight: 5.93 ozEnvironment:Storage: 14 to 122°F (-10 to 50°C)Operation: 32 to 104˚F (0 to 40˚C)
SUGGESTED - PRIOR TO FIRST USE:It is recommended that you charge your CPBC5200AC Series battery pack for 10 hours to insure a full charge.
CHARGING THE BATTERY PACKCharge the USB Battery Pack by putting the plug into an AC socket. When charging the battery pack, the LED indicator will light up automatically. Press the button to turn it off and press it again to switch the LED indicator on. Recharge the CPBC5200AC Series every 3 months when not in use to maintain peak battery performance. The battery capacity may decline after 300 charging cycles.
SAFETY PRECAUTIONBefore using the USB Battery Pack, please read the following warnings carefully. Use the product according to the procedures described in this manual. Failure to follow these safety precautions may result in fire, explosion, electrical shock or other dangers1. Store between 14 to 122°F (-10 to 50°C).Operate
between 32 to 104°F(0 to 40°C).2. Do not immerse this product in water or other liquids,
as such use may result in fire or electrical shock. If water or other liquids enter the battery interior, unplug the product immediately from any attached power source or device.
3. Do not use this product with wet hands. Moisture in or on this product may result in electrical shock.
4. Store this product in a cool and dry environment when not in use.
5. Do not puncture this product. Puncturing the battery may cause the release of harmful substances.
6. It is normal for the USB Battery Pack to become warm during charging.
7. Ensure that all users read these warnings and instructions before using.
8. Please recycle USB Battery Pack in accordance with local environmental laws and regulations
9. Do not dismantle, open or shred secondary cells or batteries.
10. Do not expose cells or batteries to heat or fire. Avoid storage in direct sunlight.
11. Do not short-circuit a cell or a battery. Do not store cells or batteries haphazardly in a box or drawer where they may short-circuit each other or be short-circuited by other metal objects.
12. Do not remove a cell or battery from its original packaging until required for use.
13. Do not subject cells or batteries to mechanical shock.14. In the event of a cell leaking, do not allow the liquid to
come in contact with the skin or eyes. If contact has been made, wash the affected area with copious amounts of water and seek medical advice.
15. Do not use any charger other than that specifically provided for use with the equipment.
16. Observe the plus (+) and minus (–) marks on the cell, battery and equipment and ensure correct use.
17. Do not use any cell or battery which is not designed for use with the equipment.
18. Do not mix cells of different manufacture, capacity, size or type within a device.
19. Keep cells and batteries out of the reach of children.20. Seek medical advice immediately if a cell or a battery
has been swallowed.
21. Always purchase the correct cell or battery for the equipment.
22. Keep cells and batteries clean and dry.23. Wipe the cell or battery terminals with a clean dry cloth if
they become dirty.24. Secondary cells and batteries need to be charged before
use. Always use the correct charger and refer to the manufacturer’s instructions or equipment manual for proper charging instructions.
25. Do not leave a battery on prolonged charge when not in use.26. After extended periods of storage, it may be necessary to
charge and discharge the cells or batteries several times to obtain maximum performance.
27. Secondary cells and batteries give their best performance when they are operated at normal room temperature (20 °C ± 5 °C).
28. Retain the original product literature for future reference.29. Use only the cell or battery in the application for which it
was intended.30. When possible, remove the battery from the equipment
when not in use.31. Dispose of properly.
LEGAL NOTICESFCC Part 15This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.– Increase the separation between the equipment
and receiver.– Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV
technician for help.If the LED indicator extinguishes automatically during the charging process, press the button to revert.
FCC WARNINGChanges or modifications not expressly approved by the party responsible for compliance with the FCC Rules could void the user’s authority to operate this equipment.
LIMITED PRODUCT WARRANTYCyberPower offers limited product warranty for the hardware of the USB Battery Pack* and the product is free from material and manufacturing defects for one year. A reasonable purchase proof with date must be provided when submission. CyberPower's sole responsibility is to repair or replace the product if a material or manufacturing defect results in product failure during its normal use. The warranty is void if the product is damaged due to abuse, alteration, misuse, negligence, incorrect voltage supply, air/water pollution, accidents and natural disasters.
INTRODUCTIONThe USB Battery Pack (CPBC5200AC Series) is a high capacity rechargeable lithium battery designed for powering up to two mobile devices such as phones, MP3 players, tablets, and handheld gaming devices while away from other power sources
FEATURES- Compact and portable design- Dual output- Built in AC plug- Battery life indicator
PRODUCT VIEW:
© 2013 CyberPower Systems, Inc. All rights reserved. Reproduction in whole or in part without permission is prohibited.
USB BATTERY PACKUSER GUIDE
Model: CPBC5200AC Series
TROUBLE SHOOTING
K09-0000172-01
POWER YOUR DEVICES
CHARGING THE POWER PACK
PAD
ITEMNO. DESCRIPTION1
2
3
4
5
Power on/ LED Indicator SwitchPower Off
LED Battery Life lndicator
USB Output Port 1*USB Output Port 2AC Input Plug
Press the buttonPress and hold for 3 secondsAs the “LED INDICATOR”table showing
5V/ 2.1A (Max.) USB output
AC 100~240V, 50/60Hz, 0.4A
CONDITIONNO. LED INDICATION1
23
Battery Life Indicator
OverloadLow Battery
Four LEDs represent 25%,50%, 75% and 100% batterylife from left to right side. All four LEDs flash simultaneously.The first LED light flashes rapidly.
LED INDICATOR
Problem Possible Cause Solution
USB BatteryPack doesnot powerthe device
1.The device is drawing too much power.
2.The battery is out of power
3.The battery pack is overloaded.
Check the power specification of the device before charging with the CPBC5200AC Series.Charge the battery pack.
Remove the device causing the overload and press the power button to return to normal mode.
Re-attach the USB connector to the socket.
Check that power is provided
USB Batterypack doesnot recharge
1.Incorrect connection between charger and USB Battery Pack.
2.No power from the source.
*Charge tablets and Apple devices through USB Output Port 1 to achieve fast charging.
1
2
34
5
Note: 1. The LED indicator will automatically switch off 5 seconds
after pressing the button.2. When the battery pack is connected to the power, the LED
indicator will light indicating the charging status. Press the button to switch off the indicator and press the button again to switch it back on.
3. All four LED indicators will flash when the battery pack is overloaded. Remove the device causing the overload and press the power button to return to normal mode.
CyberPower Systems (USA), Inc. 4241 12th Avenue East, Suite 400, Shakopee, MN 55379, U.S.A. TEL: (952) 403-9500 Toll-Free: (877) 297-6937FAX: (952) 403-0009 E-mail: [email protected]
