Universalt Control Coat Nozzles - Welcome to Nordson...

Universalt Control Coatr NozzlesCustomer Product Manual

Part 1120869_01Issued 9/12

NORDSON CORPORATION DULUTH, GEORGIA USAwww.nordson.com

This document contains important safety informationBe sure to read and follow all safety information in thisdocument and any other related documentation.

Part 1120869_01 E 2012 Nordson CorporationAll rights reserved

Nordson Corporation welcomes requests for information, comments, and inquiries about its products. General informationabout Nordson can be found on the Internet using the following address: http://www.nordson.com.

Address all correspondence to:

Nordson CorporationAttn: Customer Service11475 Lakefield DriveDuluth, GA 30097

Notice

This is a Nordson Corporation publication which is protected by copyright. Original copyright date 2012.No part of this document may be photocopied, reproduced, or translated to another language without the prior writtenconsent of Nordson Corporation. The information contained in this publication is subject to change without notice.

Trademarks

AccuJet, AeroCharge, Apogee, AquaGuard, Asymtek, Automove, Baitgun, Blue Box, Bowtie, CanWorks, Century, CF, CleanSleeve, CleanSpray, ColorMax,Color-on-Demand, Control Coat, Coolwave, Cross-Cut, cScan+, Dage, Dispensejet, DispenseMate, DuraBlue, DuraDrum, Durafiber, DuraPail, Dura-Screen,Durasystem, Easy Coat, Easymove Plus, Ecodry, Econo-Coat, e.DOT, EFD, Emerald, Encore, ESP, e stylized, ETI - stylized, Excel 2000, Fibrijet, Fillmaster,FlexiCoat, Flex-O-Coat, Flow Sentry, Fluidmove, FoamMelt, FoamMix, Fulfill, GreenUV, HDLV, Heli-flow, Horizon, Hot Shot, iControl, iDry, iFlow, Isocoil,Isocore, Iso-Flo, iTRAX, Kinetix, LEAN CELL, Little Squirt, LogiComm, Magnastatic, March, Maverick, MEG, Meltex, Microcoat, Micromark, Micromedics,MicroSet, Millennium, Mini Squirt, Mountaingate, Nordson, Optimum, Package of Values, Pattern View, PermaFlo, PicoDot, Porous Coat, PowderGrid,

Powderware, Precisecoat, PRIMARC, Printplus, Prism, ProBlue, Prodigy, Pro-Flo, ProLink, Pro-Meter, Pro-Stream, RBX, Rhino, Saturn, Saturn with rings,Scoreguard, Seal Sentry, Select Charge, Select Coat, Select Cure, Signature, Slautterback, Smart-Coat, Solder Plus, Spectrum, Speed-Coat, SureBead,Sure Coat, Sure-Max, Sure Wrap, Tracking Plus, TRAK, Trends, Tribomatic, TrueBlue, TrueCoat, Ultra, UpTime, u-TAH, Vantage, VersaBlue, Versa-Coat,

VersaDrum, VersaPail, Versa-Screen, Versa-Spray, Watermark, and When you expect more. are registered trademarks of Nordson Corporation.

Accubar, Active Nozzle, Advanced Plasma Systems, AeroDeck, AeroWash, AltaBlue, AltaSlot, Alta Spray, Artiste, ATS, Auto-Flo, AutoScan, Axiom,Best Choice, Blue Series, Bravura, CanPro, Champion, Check Mate, ClassicBlue, Classic IX, Clean Coat, Cobalt, Controlled Fiberization, Control Weave,

ContourCoat, CPX, cSelect, Cyclo-Kinetic, DispensLink, Dry Cure, DuraBraid, DuraCoat, DuraPUR, Easy Clean, EasyOn, EasyPW, Eclipse, e.dot+,E-Nordson, Equalizer, EquiBead, FillEasy, Fill Sentry, Flow Coat, Fluxplus, Get Green With Blue, G-Net, G-Site, IntelliJet, iON, Iso-Flex, iTrend,

Lacquer Cure, Maxima, Mesa, MicroFin, MicroMax, Mikros, MiniBlue, MiniEdge, Minimeter, Multifill, MultiScan, Myritex, Nano, NexJet, OmniScan, OptiMix,OptiStroke, Partnership+Plus, PatternJet, PatternPro, PCI, Pinnacle, Plasmod, Powder Pilot, Powder Port, Powercure, Process Sentry, Pulse Spray,

PURBlue, PURJet, Ready Coat, RediCoat, Royal Blue, Select Series, Sensomatic, Shaftshield, SheetAire, Smart, Smartfil, SolidBlue, Spectral, SpeedKing,Spray Works, Summit, SureFoam, Sure Mix, SureSeal, Swirl Coat, TAH, ThruWave, Trade Plus, Trilogy, Ultra FoamMix, UltraMax, Ultrasaver, Ultrasmart,

Universal, ValueMate, Versa, Vista, Web Cure, YESTECH, and 2 Rings (Design) are trademarks of Nordson Corporation.

Designations and trademarks stated in this document may be brands that, when used by third parties for their own purposes,could lead to violation of the owners' rights.

Never Seez is a registered trademark of Bostik Inc.Viton is a registered trademark of DuPont Dow Elastomers. L.L.C.

Table of Contents i

Part 1120869_01E 2012 Nordson Corporation

Table of ContentsDescription 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Application Guidelines 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Parameters 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Operating Conditions 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Operational Capability 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Troubleshooting 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Nozzle Service 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Removing or Installing a Nozzle 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Remove a Nozzle 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Install a Nozzle 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Cleaning Nozzles 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Parts 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Blank Nozzles 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Recommended Spare Parts and Supplies 19. . . . . . . . . . . . . . . . . . . . . . . .

Technical Data 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Torque Specifications 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Nozzle Identification 20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table of Contentsii

Part 1120869_01 E 2012 Nordson Corporation

Control Coat nozzle

Universal Control Coat Nozzles 1


Universal Control Coat Nozzles

WARNING! Allow only personnel with appropriate training and experience tooperate or service the equipment. The use of untrained or inexperiencedpersonnel to operate or service the equipment can result in injury, includingdeath, to themselves and others, and damage to the equipment.

DescriptionThis manual provides setup, operation, troubleshooting, service, and partsinformation specific to Control Coat nozzles for continuous or nonwovenintermittent applications. For optimal performance, Nordson Corporationrecommends a single-module SpeedCoat unibody (UA-UMSC-01-____-SPL16) applicator configuration.

Control Coat nozzles deliver highly uniform slot-like coatings with excellentleading, trailing, and side edges for diverse product assembly applications.The all-steel design uses a central sheet of adhesive that is fiberized byprocess air curtains angled to either side to produce a uniform slot-likepattern ideally suited to numerous continuous or intermittent web coating andproduct assembly applications. Patterns are exceptionally uniform and edgecontrol is excellent. These nozzles are available in versions compatible withUniversal series modules. Universal Control Coat nozzles are reversible andmay be oriented for either right-hand or left-hand coverage.

NOTE: Refer to Parts for nozzle part numbers. Refer to Nozzle Identificationfor an explanation of nozzle description codes.NOTE: Refer to the applicator manual for all applicator-related informationand procedures.

Universal Control Coat Nozzles2


Application GuidelinesThis section provides installation, setup, and operational information specificto applications using Control Coat nozzles.

ParametersThese illustrations depict a vertically downward spraying lamination adhesiveapplication. Other installation configurations, including horizontal adhesiveapplication, are also possible. In all cases, the basic principles in thisquick-reference document may be used as a guide for achieving optimumperformance.

Support roller

Web path

Web A

Web B

Combining point (nip rollers)

Web path

A

C

D

Adhesive area

Figure 1 Isometric view of a single-module Universal applicator with a Control Coat nozzle



Application point

A

B

Web

path

Web

path

C

Ideal installationposition

Possible installationposition

Incorrect installationposition

Figure 2 Side view of single-module Universal applicator with a Control Coat nozzle (parameters A-C)

Parameter Description Minimum Value Maximum Value Typical ValueA Nozzle tip to substrate 10 mm (0.38 in.) 20 mm (0.79 in.) 15 mm (0.59 in.)

Explanation: Less than the minimum value may result in nozzle contamination; greater thanthe maximum value may result in less than optimum edge control.

B Nozzle angle to substrate 85 degrees 95 degrees 90 degreesExplanation: The operational recommendation is 90 degrees.

C Upstream web support rollerto application point 50 mm (2.0 in.) 150 mm (6.0 in.) 100 mm (4.0 in.)Explanation: The point of application for nonporous material should be on the support roller.Follow the guidelines above for porous materials.



Parameters (contd)

Substrate

D

EF F

Partial

Full coverage (E)

coverage (D)

Figure 3 Front view of a single-module Universal applicator with a Control Coat nozzle (parameters D-F)

Parameter Description Minimum Value Maximum Value Typical ValueD Control Coat pattern width

(5-400 mm)5-6 mm

(0.2-0.3 in.) 25 mm (1.0 in.) Full width (25 mm)Explanation: Control Coat nozzles are available in 1/4, 1/2, 3/4, and full-width versions.Patterns are accommodated through the use of one or more partial- or full-coveragenozzles.

E Adhesive pattern width As required As required As requiredF Pattern to substrate edge 3 mm (0.1 in.) As required As required

Explanation: Control Coat edge control is + 1.5 mm (0.06 in.).



Operating ConditionsNOTE: Refer to the applicator manual for additional specifications.

Condition Minimum Value Maximum Value Typical ValueAdhesive viscosity 1,000 cps 5,000 cps 1,000-3,000 cpsAdhesive flow per nozzle 5 g/min 50 g/min As required

Explanation: Minimum and maximum flow are a function of viscosity.Refer to Operational Capability later in this manual for additionalinformation.

Pattern air flow per nozzle(see Note A) 0.5 scfm 1.5 scfm 1.0 scfm

Pattern air temperature 0 _C (0 _F) aboveadhesive temperature

14 _C (25 _F) aboveadhesive temperature

0 _C (0 _F) aboveadhesive temperature

Pattern air pressure(see Note B) 0.5 bar (7.5 psi) 2 bar (30 psi) 1.0-1.5 bar (15-22 psi)NOTE A: Avoid using too much air pressure. Maintaining larger adhesive filaments will improve process stability,

increase bond strength, and reduce air consumption.B: The pattern air flow path is critical. Ensure that the pattern air supply lines are properly sized and that they

are not kinked in a way that restricts air flow.



Operational CapabilityMost production environments require a range of flow rates at a fixedmaterial viscosity. Application requirements will determine the selection ofnozzles. To aid in nozzle selection, the Control Coat nozzle operatingcapability is shown graphically in Figure 4.

Figure 4 Control Coat nozzle operating window capability



TroubleshootingProblem Possible Cause Corrective Action Example

1. Good pattern (forreference only)

Not applicable Not applicable

2. Pattern breakingup with resultingcontamination ofmachine

Adhesive temperature toohigh; viscosity too low(resulting in brokenadhesive filaments)

Verify that viscositycorresponding toapplication temperature isin adherence to thepublished best practices.

Pattern air flow/pressuretoo high for given flow rate

Reduce the pattern airflow/pressure.

3. Gaps in adhesivepattern

Adhesive temperature toolow (resulting in poorprocessibility)

Increase the adhesivetemperature and ensureadherence to thepublished best practices.

4. Pattern drop in andout, resulting ingaps and erraticoperation

Nozzle back pressureinadequate for stableoperation (low-flowcondition)

Refer to the operatingwindow graphics todetermine if a low-flowcondition exists for thegiven adhesive viscosity.Decrease the adhesivetemperature slightly toincrease viscosity andresistance to flow.

Continued...



Troubleshooting (contd)

Problem Possible Cause Corrective Action Example5. Ends of patterns

pull inward,resulting in gapsbetween adjacentnozzles oradhesive filamentscombining(causing heavyand light areas inpattern)

Adhesive temperature toolow or pattern air flow toolow for given adhesive flow

Verify that viscositycorresponding toapplication temperature isin adherence to thepublished best practices.Adjust the pattern airflow/pressure.

Air currents created byhigh speed movement ofconverting machinery areaffecting the strands

Verify that viscositycorresponding toapplication temperature isin adherence to thepublished best practices.Adjust the pattern airflow/pressure.

6. Adhesive leakageon one module

Nozzle O-ring missing ornozzle too loose(under-tightened)

Install a new nozzleO-ring, replace the nozzle,or tighten the nozzle clampscrew.



Nozzle ServiceRemoving or Installing a Nozzle

You will need the following items:S Appropriate tools, including a torque wrenchS Drain pans and disposable ragsS O-ring lubricant (for lubricating nozzle O-rings)

WARNING! System pressurized! Relieve system hydraulic pressure beforebreaking any hydraulic connection or seal. Failure to relieve the systemhydraulic pressure can result in the uncontrolled release of hot melt or coldadhesive, causing personal injury.

WARNING! Molten material! Wear eye or face protection, clothing thatprotects exposed skin, and heat-protective gloves when servicing equipmentthat contains molten hot melt. Even when solidified, hot melt can still causeburns. Failure to wear appropriate personal protective equipment can resultin personal injury.

Remove a Nozzle1. Heat the system to application temperature.2. Relieve system pressure. Refer to the applicator manual as needed.3. Trigger the applicator solenoid valves to relieve any remaining pressure.4. Shut off the module-actuating air.5. Decrease the pattern air pressure. Leave just enough air pressure to

prevent adhesive from entering the pattern air outlet on the module.See Figure 5.6. Back the nozzle-retaining clamp screw all the way out until it stops (1).7. Push up (2) on the nozzle-retaining clamp screw to eject the nozzle.



Install a NozzleSee Figure 5.1. Clean (3) the mating surface where the nozzle will be seated.2. Inspect the nozzle seal, replace if necessary, and ensure that the seal is

lubricated and properly positioned in the seal bore.3. Carefully angle and insert the nozzle in the module seat (4, 5).

CAUTION! Overtightening a nozzle-retaining clamp screw can damage themodule.

4. Tighten (6) the nozzle-retaining clamp screw to 2.8 NSm (25 in.-lb).



Loosen clamp screw Clean mating surface

5 6Angle and insert nozzle

1 2 3

4Tighten clampscrewto 2.8 NSm (25in.-lb)

Push up on clampscrew to eject nozzle

Seat nozzle andhand-set clamp screw

Figure 5 Nozzle removal or installation (shaded nozzle is a generic shape)1. Loosen clamp screw2. Push up on clamp screw to eject

nozzle

3. Clean mating surface4. Angle and insert nozzle

5. Seat nozzle and hand-setclamp screw

6. Tighten clamp screw to2.8 NSm (25 in.-lb)



Cleaning NozzlesYou will need the following items:S Appropriate toolsS Cleaning supplies (refer to Tables1 and 2)S Drain pans and disposable ragsS O-ring lubricant (for lubricating nozzle seals)

1. Remove the nozzles. Refer to Remove a Nozzle earlier in this section.2. Disassemble (refer to Parts) and clean the nozzles using one of the

Nordson-recommended methods shown in Tables 1 and 2. Use onlycleaning agents recommended by the adhesive supplier.

WARNING! System pressurized! Relieve system hydraulic pressure beforebreaking any hydraulic connection or seal. Failure to relieve the systemhydraulic pressure can result in the uncontrolled release of hot melt or coldadhesive, causing personal injury.

WARNING! Molten material! Wear eye or face protection, clothing thatprotects exposed skin, and heat-protective gloves when servicing equipmentthat contains molten hot melt. Even when solidified, hot melt can still causeburns. Failure to wear appropriate personal protective equipment can resultin personal injury.

WARNING! Risk of explosion or fire. Follow the safety guidance and heatingrecommendations on the Material Safety Data Sheets (MSDSs) for youradhesives and nozzle-cleaning solutions.

WARNING! Risk of explosion or fire. Use a controlled heating device, suchas a thermostatically controlled hot plate, to heat cleaning fluid, includingNordson Type-R fluid.

CAUTION! Risk of equipment damage. Do not use a wire brush (or a brushwith bristles harder than the nozzle) to clean nozzles.



Table 1 Preferred Nozzle Cleaning MethodCleaning Method Procedure

Oven (preferred) WARNING: Risk of explosion, fire, or toxic vapor release.Depending on the type of adhesive and/or organic solvent usedwith the nozzles, heating them in an oven can cause a hazardousevent. Before using an oven to clean nozzles, consult with theoven manufacturer about the viability of this method and thesafety risks. Follow the manufacturer's recommendations.WARNING: Use the oven heating controls to keep the oven at thedesired temperature. Do not use an oven that does not haveheating controls.

CAUTION: Risk of equipment damage. Remove seals beforecleaning nozzles in an oven. Failure to do so can cause a chemicalreaction that will permanently damage the nozzles.

a. Ensuring that seals have been removed from the nozzles, place them inan electric oven heated to approximately 385 _C (725 _F). Allow thenozzles to bake for approximately 3-4 hours.

WARNING: The heating temperature and time may need to beadjusted based on the oven type, the adhesive type, and theamount of char buildup on the nozzles. Nordson Corporationrecommends testing this procedure on discarded nozzles prior tousing it on good nozzles.

WARNING: Risk of fire. Use a heat-proof cloth to clean nozzles. Evencotton can burn in high-temperature conditions.

WARNING: Risk of equipment damage. Handle nozzles carefully toavoid denting the orifices, which can degrade the adhesive pattern.

b. Turn off the oven and allow the nozzles to cool; then remove thenozzles.

c. Wipe the nozzles with a soft cloth and then gently blow air through thenozzle orifices from the mounting side of the nozzle.



Cleaning Nozzles (contd)

Table 2 Other Nozzle Cleaning MethodsCleaning Method Procedure

Citrus-based solutionand ultrasonic tankNOTE: This is the mostthorough method.

a. Place the nozzles in citrus-based solvent/degreasing solution and soakthem overnight or for approximately 4 hours. This dissolves and loosens theadhesive and char buildup.

b. Remove the nozzles from the citrus-based solvent/degreasing solution andplace them in an alkaline solution heated to the appropriate temperature(refer to the MSDS) in an ultrasonic tank. Soak the nozzles forapproximately 10 minutes. This will remove adhesive and char from theorifices.

c. Scrub the nozzles with a soft, non-metallic brush to remove debris.d. Gently blow air through the nozzle orifices from the mounting side of the

nozzle.Nordson Type-R fluid a. Place the nozzles in a controlled heating device containing Nordson Type-R

fluid and heat it above the melting point of the adhesive (refer to the MSDS).b. Scrub the nozzles with a soft, non-metallic brush to remove debris.

Electric heat gun a. Heat the nozzles with a flameless electric heat gun.b. Scrub the nozzles with a soft, non-metallic brush to remove debris.

Ultrasonic tank a. Place the nozzles in an alkaline solution heated to the appropriatetemperature (refer to the MSDS) in an ultrasonic tank. Soak the nozzles forapproximately 10 minutes.

b. Scrub the nozzles with a soft, non-metallic brush to remove debris.c. Gently blow air through the nozzle orifices from the mounting side of the

nozzle.

3. If there is any remaining char buildup on the nozzles, gently scrape thechar from the nozzles.

4. Reinstall the nozzles. Refer to Install a Nozzle earlier in this section.5. Restore the system to normal operation.



This page intentionally left blank.



PartsA Control Coat nozzle is an assembly of parts that are collectively referred toas a “nozzle.” Table 3 shows the nozzle part numbers. See Figure 7 and theaccompanying parts list for the individual nozzle parts.

Table 3 25-mm Control Coat NozzlesUniversal Control Coat Laminating Nozzles (25 mm)

NozzlePart Number

Coveragemm (in.) Description

7128166 5 (0.20) Left orientation7128167 5 (0.20) Right orientation396271 5 (0.20) Center orientation8061391 10 (0.40) Left orientation8061392 10 (0.40) Right orientation396270 10 (0.40) Center orientation8061393 15 (0.60) Left orientation8061394 15 (0.60) Right orientation8061396 15 (0.60) Center orientation8061030 20 (0.80) Left orientation8061071 20 (0.80) Right orientation8054729 20 (0.80) Center orientation7101042 25 (full coverage) Full coverage

NOTE: All nozzles include the following seal: part 250294, quadring 2.9 x1.78.

Figure 6 25-mm Control Coat nozzle



Item Part Description Quantity Note— - - - - - - UCCDIE-SL10/B/XX/X — A, B1 396771 S Adapter UM DL25 H8 f.CC 12 - - - - - - S Material nozzle UM rh DL25 AB25 13 - - - - - - S Material nozzle UM lh DL25 AB25 14 - - - - - - S Air nozzle UM rh DL25 AB25 15 - - - - - - S Air nozzle UM lh DL25 AB25 16 7101047 S Shim plate UM DL25 1slot 25x0,1 17 254676 S Allan head cap screw M4x20 DIN912-A2-70 28 250073 S Allan head cap screw M4x10 DIN912-A2-70 19 254673 S Allan head cap screw M3x10 DIN912 SST 110 258988 S Allan head cap screw M3x12 DIN912 SST 211 404488 S Parallel pin D4h6x20 DIN6325,-D 112 7100820 S Parallel pin D3h6x20 DIN6325-D 113 257410 S Parallel pin D3m6x6 DIN7 214 250294 S Quadring 2,9x1,78 115 253890 S O-ring 3x1 Viton 1

NOTE A: Refer to Table 3 for nozzle part numbers.B: Refer to Nozzle Identification later in this manual for an explanation of the nozzle description code.

2

3

4

5

6

9

7

8

11 12

13 14

10

15

1

Figure 7 25-mm Control Coat nozzle parts



Blank NozzlesA blank nozzle has no air or adhesive openings. Blank nozzles, incombination with active and partial nozzles, aid in achieving a desiredadhesive pattern.

Item Part Description Quantity Note1 1062137 NOZZLE,BLANK,UNIVERSAL,25MM AR2 1022028 S O-RING,75 VT,.578ID X .040 13 1045216 NOZZLE,BLANK,UNIVERSAL,UM22/UM25 AR4 1019706 S O-RING,VITON,.146ID X .031W,BROWN 1

AR: As Required

2

1

4

3

Figure 8 Blank nozzles



Recommended Spare Parts and Supplies

Part Description Note250294 QUADRING, 2.9 X 1.781120201 LUBRICANT, O-RING, NSF-H1, 10 ML TUBE (for O-rings)1108371 LUBRICANT, NEVER-SEEZ, NSF-H1, FOOD GRADE (for screw threads)

Technical DataTorque Specifications

These torque specifications are also stated within the appropriateprocedures.

Item Torque SpecificationNozzle-retaining clamp screw 2.8 NSm (25 in.-lb)



Nozzle IdentificationUse the table shown below to decipher the Nordson Corporation descriptioncode used to identify nozzles.

Example Nozzle Description Code

U CC DIE - S L 10 B / 25 / 251 2 3 4 5 6 7 8 9 10 11 12 13

Nozzle Identification Option Code PostionsCode Positions

Code Position(s) Description Values1 Nozzle series U = Universal2-3 Type of nozzle CC = Control Coat4 Hyphen -5 Material S = Steel6 Use L = Lamination

7 Shim plate thickness

10 (typical, indicating that the thickness of the shim plate is0.10 mm)orXX (where XX is a two-digit number that represents thethickness of the shim plate in tenths of a millimeter)

8 Nozzle width B = 25 mm9 Slash /

10 Application width25 (application or pattern width)orXX (where XX represents the application width)

11 Slash /

12-13 Offset (mm)

0 = No offsetorXX.X (where XX.X represents the offset in millimeters)NOTE: Offset is the distance that the center of the pattern is offsetfrom the center of the nozzle.

NOTE: Available configurations are subject to change. Contact your Nordson representative for the most currentconfiguration choices. Special nozzle configurations with multiple stripes are available as engineered specials.

Universalt Control Coat Nozzles - Welcome to Nordson...

Documents

Transcript of Universalt Control Coat Nozzles - Welcome to Nordson...