Universal I/O module(Option: Infrared sensor module) OO M ...
Transcript of Universal I/O module(Option: Infrared sensor module) OO M ...
V200415SOYALACCESS CONTROL SYSTEM
®
LED1LED2/3
DO1 ~ DO4 DI1 ~ DI4
DI4
DI4DO4
DO1DO2DO3DO4 DI3
DI3DO3
DI2
DI2DO2
DI1
DI1 L+ V+ V-L-DO1
RS485TxRx
POWERRS485DI1~4DO1~4
AR-403-IO-0001M-IR
(AR-403-IO-0001M-IR)
(AR-403-IO-0404M)
(AR-403-IO-0202M)(AR-403-IO-0404M)(AR-403-IO-0202M-IR)
1
159
2
2610
3
3711
4
4812
AR-403-IO-0001M-IR
AR-403-IO Series
3 ~ 6 cm
7 ~ 9 cm
10 ~ 15 cm
A
Y
B(Y0)
Universal I/O module(Option: Infrared sensor module)(Up to 24VDC/2000mA High Power MOSFET output)
AR-403-IO Series
Product
PIN Define
Infrared Module / I/O Module 1 Product
Indicator
Cable Instruction
Application of mailbox---Wiring Diagram
Wiring & Application
Indicator Color DescriptionLED1 Green POWERLED2 Green
RS485 TxRx Communication indicatorLED3 RedDO1
Red
DO1,Action indicator(Mailbox mode: letter indicator, blue LED)
DO2 DO2,Action indicatorDO3 DO3,Action indicatorDO4 DO4,Action indicatorDI 1
Green
DI1, Action indicatorDI 2 DI2, Action indicatorDI 3 DI3, Action indicatorDI 4 DI4, Action indicator
Sensor fordelivering letters
Indicator for letters inside
Door Sensor
Cabinet Lock
【AR-403-IO-0404M / AR-403-IO-0202M-IR】Cable Instruction:
【AR-403-IO-0001M-IR】Cable Instruction:
Function Cable AR-403-IO-0404M(Standard mode) Description
AR-403-IO-0202M-IR (Mailbox mode)
V- Input 1 Power GNDVIN Input 2 Positive power supply, range of volt: 9~24VRS-485 LA 3 RS-485 L+ contactRS-485 LB 4 RS-485 L- contact
DI1 5
Input point, triggered by the low electric potential
Delivering Letters Detection:When DI1 detect the letters are dropped, DO1 will be active to light on indicator.
DI2 6 Door Status Detection: When DI2 door sensor detects that the door is closed, the indicator will light off
DI3 7DI4 8
DO1 9MOSFET output, driven by 24VDC / 2A
Letters Indicator Output: When DI1 detects the letters are dropped and it will output 1Hz ON/OFF flashing signal; Stop the output till DI2 detects OFF-ON-OFF motion of the door.
DO2 10 Cabinet Lock Output: DO2 connect Lock to open the mailbox DO3 11DO4 12
Function Cable DescriptionV- Input 1 Power GNDVIN Input 2 Positive power supply, range of volt: 9~24VInfrared Action Output 3 Output , Power Consumption : 24VDC / 600mA Reserved 4 ---
LED
Infrared Module(Optional)
*Reading Range:
Remote ControlSequential Control : Frequency-adjustablecontinuous pulse outputSupport Modbus RTU/Soyal Protocol Programmable
ControllerFanless Embedded
ComputerTouch panel
PCIndustrial PC
Mode I : Standard Modbus I/O Module
Mode II : Mailbox Module
AR-403-IO-0404MAR-403-IO-0202M-IR
1
2
3
4
5
6
7
8
9
10
11
12
12VGND
LA+
DI3DI4
DI2DI1
DO3DO4
DO2DO1
LB-
E/V5 Controller
COM
N.C.
12V
12V
12V
GND
Output
GND
GND
Sensor
Lock2
O
12VDC 725L485Power
Mailbox 1
Mailbox 2
V200415SOYALACCESS CONTROL SYSTEM
®
P1
P1 P2
P2
1
3
2 54
DI1D I2 DI1D I2
DI1
DI2
DI1
DI2
Universal I/O module(Option: Infrared sensor module)(Up to 24VDC/2000mA High Power MOSFET output)
AR-403-IO Series
Direction for use
DI1/3: Sensor When the letters are dropped, the sensor w i l l de tec t the motion.
DO2/4: Cabinet lockThe mailbox will open after the card is presented
DO1/3: Indicator The Indicator will light up when there are letters in the mailbox
DI2/4: Door SensorClose the door after taking out the letters. Door Sensor detects the door is closed and the indicator will be off.
Mode III : Multiple delay function
Mode IV/V : Rear Detection / Front Detection(Remain direction recognition)
Output 1: Falling edge Trigger (DO0)
Output 2: Rising edge Trigger (DO1)
Output 3: Toggle trigger (DO2)
Output 4: Non-distortion Pulse Delay (DO3)
Trigger
Trigger
Trigger
DelayTime
DelayTime
DelayTime
DelayTime
DelayTime A
DelayTime B
Trigger Trigger Trigger TriggerTrigger Trigger Trigger Trigger
※ Support Firmware version 401_MBox_V0209_190912.ISP and after.
Commview Setting steps:
Commview Software Update
Software Sett ing
(1) Select COM Port
(2) Click “Read” to get Node number
(3) Select Mode Standard----- Mode I: Standard Modbus I/O Module
Mailbox------- Mode II: Mailbox Module
Delay M-0--- Mode III: Multiple delay function
FF/RF falling----- Mode IV: Rear Detection
FF/RF rising----- Mode V: Front Detection
(4) Enter delay time (Mode 3/Mode 4) Make sure Nord number is consistent as above(5) Click “Write”, finish setting.
Please download software【SoyalDeviceTool】from Soyal website
Close thedoor of mailbox
FrontDetection
Sensing Coil Sensing Coil
RearDetection
FrontDetection
RearDetectionVehicle Detected
Vehicle Detected
Vehicle Detected
Vehicle Detected