Unit 1 - Voltage and Current References1.pdf

7/27/2019 Unit 1 - Voltage and Current References1.pdf

1/48

Voltage and Current References

Biswajit Behera

[email protected]

9853420601


2/48

Voltage & Current References

An Ideal reference should be independent of power supply, processand temperature variations.

The term Reference is used when the current or voltage values have

more precision and stability than ordinarily found in a source.

A high performance voltage reference can be used to implement a

high performance current reference and vice versa.

Voltage and current references used to bias the current sources and

sinks, differential amplifiers, operational amplifiers etc..

[email protected]
mailto:[email protected]:[email protected]


3/48

To reduce powerdissipation, the resistors

must be made very large,

which requires large area

on die.

Not practicable.

[email protected]


4/48

Used in simple current mirrorto bias the M2 transistor

[email protected]


5/48

Calculate Vref?

[email protected]


6/48

Calculate Sensitivity of Vref to VDD ?

[email protected]


7/48

Calculate Temperature Coefficient of Vref ?

How to make Vrefas more than VGS ?

[email protected]


8/48

How to achieve Vrefas more than VGS ?

[email protected]


9/48

Small layout because both are transistors

[email protected]


10/48

Calculate Vref?

[email protected]


11/48

Calculate Sensitivity of Vrefto VDD ?

[email protected]


12/48

Calculate TC (Vref) ?

How to achieve zero TC (Vref) ?

[email protected]


13/48

Condition for zero TC(Vref)

[email protected]


14/48

[email protected]


15/48

Solution :

[email protected]


16/48

Solution (Contd.):

[email protected]


17/48

This is also called Dual Reference voltage divider

[email protected]


18/48

[email protected]


19/48

Solution :

[email protected]


20/48

Application ofDual reference voltage divider

[email protected]


21/48

Current Source Self Biasing

Main drawback of References based on voltage divider are

very sensitive to supply voltage, process and temperature.

Three important types of current source self biasing are :

1. Threshold voltage referenced self biasing

2. Diode referenced self biasing

3. Thermal voltage referenced self biasing

[email protected]


22/48

1. Threshold voltage referenced self biasing

[email protected]


23/48

Ideally the Reference current is independent of power supply.

[email protected]


24/48

This circuit requires a start up circuit, for flawless functionality. Why ?

[email protected]


25/48

Requirement ofStart-Up circuit

[email protected]


26/48

Threshold Referenced Self biasing with

start-up circuit

When I1 = I2 = 0 then

VGS1 = I2R = 0 and VDS1=VGS2 = 0.

Now M5 transistor provides current

to flow through drain of M1. so I1 increases

and so I2.

VG2 increases

VGS5 decreases

When I1 reaches point A,

M5 turns off as VGS5 < Vt5.

The start up circuit will be idle until I1 (=I2)

Becomes again zero.

[email protected]


27/48

2. Diode Referenced Self Biasing

VBE referenced self biasing in CMOS

[email protected]


28/48

CMOS circuits rely on using well transistors, which are vertical bipolar

transistors, that use wells as their bases and the substrates as their

collectors.

In an n-well process, the vertical bipolar transistors are PNP type with

their collectors connected to ground.

In a p-well process, the vertical bipolar transistors are NPN transistors,

with their collectors connected to the positive power supply

[email protected]


29/48

The parasitic transistor is connected as a

diode ( base and collector are tied

together), which reduces the effectiveresistance in series with the diode and the

leakage to substrate.

The cascode mirrors made with M1

through M8 force the same current, I, toflow through D1 and R.

Assuming matched devices, VGS1 = VGS2

then

[email protected]


30/48

Advantage : compared to threshold referenced self biasing circuit, this has

better matching, from wafer to wafer and on the same die, of the diodevoltage(VBE) over threshold voltage.

This circuit also depends on temperature.

[email protected]


31/48

3. Thermal Voltage Referenced Self Biasing

[email protected]


32/48

Disadvantage :

1. Since the voltage drop across resistor R is very small, Mismatches

in the gate source voltages of M1 and M2 are made large variations

in reference current I.

2. Susceptibility to externally coupled noise across R.

[email protected]


33/48

Advantage : The reference current of this circuit has less dependence on temperature.

[email protected]


34/48

Disadvantage of above three circuits

[email protected]


35/48

Bandgap Voltage References

[email protected]


36/48

Negative Temperature Coefficient (TC)

The forward voltage of a PN junction ( VBE of a diode

connected BJT) exhibits a negative TC.

For a diode connected BJT,

We know

[email protected]


37/48

Positive Temperature Coefficient (TC)

[email protected]


38/48

[email protected]


39/48

[email protected]


40/48

[email protected]


41/48

Practical circuit to add

[email protected]


42/48

[email protected]

l ll h h l b l


43/48

But CMOS circuits rely on using well transistors, which are vertical bipolar

transistors, that use wells as their bases and the substrates as their

collectors.

In an n-well process, the vertical bipolar transistors are PNP type with

their collectors connected to ground.

In a p-well process, the vertical bipolar transistors are NPN transistors,

with their collectors connected to the positive power supply

[email protected]


44/48

[email protected]

h ibl l i


45/48

Other Possible Implementation

[email protected]


46/48

[email protected]

TC of Bandgap Reference Voltage


47/48

TC of Bandgap Reference Voltage

[email protected]


48/48

Unit 1 - Voltage and Current References1.pdf

Documents

Transcript of Unit 1 - Voltage and Current References1.pdf