UNIP12AD-1HMC-0 - unitech.lighting · A pplication Downlight PanelLight Flood Light Spotlight...
Transcript of UNIP12AD-1HMC-0 - unitech.lighting · A pplication Downlight PanelLight Flood Light Spotlight...
A pp lication
Downlight Panel Light Flood
Light
Spotlight Ceiling Light Decorative Light Floor Light
UN IP12AD-1HMC-0
S ummar y
UNIP12AD-1HMC-0 is a 12W AC/DC constant current mode output LED driver featuring the multiple levels
selectable by DIP switch , complies with DALI standard protocol IEC 62386,and provides multiple
dimming function (DALI,1-10V active signal ,PWM, adjustable resistance, and Touch DIM) to achieve a
smooth dimming effect.
Product Features
·Single channel output, output current level selectable by DIP S.W.
· Support a variety of dimming modeDALI/1-10V active signal/adjustable resistance/
PWM/Touch DIM
·Built-in active PFC function
·Class 2 power supply. Full protective plastic housing
·Dimming effect smooth, no flicker
·Protections: Short circuit, over load, over temperature
·Suitable for indoor LED lighting application, such as down light,
spot light,panel light, and so on
Technical Paramaters
200mA 250mA 300mA 350mA
9-40V 9-40V 9-40V 9-34V
Model UN IP12AD -1H MC -0
I n pu t
Efficiency >85%@230VAC,Full load
Voltage 220VAC-240VAC
Frequency Range(Hz) 50/60Hz
Power Factor ≥0.95@230VAC,Full load
THD(full load) <10%@230VAC, Full load
AC Current(max) 0.07Amax@230VAC
Standby power <0.5W
Inrush Current(max) Cold start,18A(twidth=14us measured at 50% Ipeak)@230VAC
Output
Current(mA)/Voltage (VD
Power(W)
C)200mA/9-40VDC/8W 250mA/9-40VDC/10W
300mA/9-40VDC/12W 350mA/9-34VDC/11.9WCurrent Selection Table
ON OFF
Remark: Function default setting is: 200mA
(@switch are all OFF state)
Ripple Current <3%
Channel 1
Current Tolerance ±5%
No load output voltage 50V Max
Turn on delay Time <1.5s, at230Vac
Funct ionDimming Type DALI/1-10V active signal/adjustable resistance/PWM/Touch DIM
Priority order DALI>(1-10V active signal/adjustable resistance/PWM)> Touch DIM
Protection
Short Circuit Close output, recovers automatically after fault removed
Over Load When the output voltage is exceeded, the output current decreases and, recovers automatically when
The loa
Over Temperature Shut down the output, recovers automatically when temp. back to normal.
Others
Working Temp. -20℃~50℃
Storage Temp., Humidity -40℃~85℃, 20-90%RH
tc 90℃
Material PC
IP Rating IP20
Lifetime 50,000h@tc℃:80
Warranty Condition 5 Years
Switch Cycle >100,000 tims
Packing(weight) Net weight: 125g±5%/PCS; 50PCS/Carton; 6.65kg±5%/Carton; Carton Size319*254*136mm(L*W*H)
Dimension 150*43*29mmL*W*H
2 9
43 32.5
25.0
D ime n s io n (mm)
150.0
140.5
90.5
DALI&0/1-10V Constant Current Dimming Driver
Wir i ng D i ag r am
Pu sh D IM (To u ch D I M ) Diag ram
Remark: Only use open push button without indicator light. Maximum cable length between each Unit: 20 meters.
Pu sh D I M Funct ion
1. Short press the Touch DIM switch (<0.5s) to control the lamp on or off.
2. Long press the Touch DIM switch (>0.5s) to dim the brightness of light. The dimming direction will change every time after pressing switch.
3. Double-click the Touch DIM switch (<0.3s), then all lamps connected on the device will be set maximum brightness.
4. The brightness adjustment range is 1%-100%, and the light can be turned off through short pressing when doing the adjustment with long
pressing Touch DIM switch.
5. With the Power off memory function, the power-down state will be recovered when power on again.
D A L I Diag ram
DADA DALI Driver 1LED+
LED-LN
DADA
DALI Driver 1LED+LED-L
N
L
N
DALI Controller
DA
DALI Driver 1LED+LED-
DA L N
DA
DALI Driver 1LED+LED-
DA L N
Push DIM Panel(TouchDIM)N L
Caut ions
1.This product should be installed by qualified personnel.
2.This product is non waterproof, need to avoid sun and rain.In case of outdoor use, please ensure it is mounted in a water proof enclosure.
3.Good heat dissipation conditions extend product life. Please install the product in a well-ventilated environment.
4.Please make sure LED power supply output voltage, current is used to meet the product requirements.
5.Please ensure that adequate sized cable is used from the controller to the LED lights to carry the current. Please also ensure that the cable
is secured tightly in the connector.
6.Due to safety concerns, PVC or rubber cord of 0.²75- 1.5mm is recommended for input and output terminal(s)(excluding signal terminals).
Flat power cord is not suitable.Ensure all wire connections and polarities are correct before applying power to avoid any damages to the LED lights.
7. In case of malfunction, do not repair it yourself.
The contents of this manual are updated without prior notice. If the function of the product you are using is inconsistent with the instructions, the function of the product
shall prevail.Please contact us if you have any questions .
D A L I D imming Curve
0
120 40 60 80 100 120 140 160 180 200 220 240 254
100
80
60
40
20
120
0.4
0.3
0.2
0.1
0
1 1 0 20 30 40 50
DALI DimmingLevel
Outp
ut
Curr
ent(
%)
1-10V/PWM/adjustable resistance
80
60
40
20
100
Derat ing Curve
120
Load(%
)
0 -20 -10 0 10 20 30 40 50 60
Ambient Temperature
120
100
80
60
40
Input signal (%)
20
0
Outp
ut(%
)
0 7 1 3 19
26
32
39
45
52
58
65 7 1 7 7 84
90 97
·DALI Mode
DALI Signal Input
·1-10V/PWM/adjustable resistance
DALI Master
L
N
DA
LI
DA 1
DA 2LED+
LED -
Sign+
Sign -
INP
UT
Lamp
L
N
DA
LI
DA 1
DA 2LED+
LED -
Sign+
Sign -
INP
UT
Lamp
0-10V Dimmer
·Touch DIM Mode
N L
DA
LI
DA 1
DA 2LED+
LED -
Sign+
Sign -
INP
UT
Lamp
DALI&0/1-10V Constant Current Dimming Driver
DALI Constant Current Dimming Driver
A p p l i c a t i o n
Downlight Panel Light Ceiling Light Decorative Light Floor Light Flood LightSpotlight
U N I P 12D - 2H M C - 0 ( P r o d u c t No. : 1 0 2 1 0 1 1 0 0 1 0 1 )
S u m m a r y
UNIP12D-2HMC-0 is a 12W AC/DC constant current mode output LED driver featuring the
multiple levels selectable by DIP switch and complies with DALI standard protocol IEC 62386-209.
UNIP12D-2HMC-0 can be connected to DALI main controller or Touch DIM to a chieve a smooth
dimming effect.
P r o d u c t F e a t u r e s
·Two channel output, output current level selectable by DIP S.W.
·Meet DALI Protocol IEC 62386-209
·Support Touch-DIM function
·High efficiency up to 83 %
·Built-in active PFC function
·Dimming effect smooth, no flicker
·Protections: Short circuit, over load, over temperature
·Suitable for indoor LED lighting application, such as down light, panel light,
and so on
T e c h n i c a l P a r a m a t e r s
M odel U N I P 1 2 D - 2 H M C - 0
I n p u t
Efficiency >83%@230VAC,Full load
Voltage 220VAC-240VAC
Frequency Range(Hz) 50/60Hz
Power Factor ≥0.95@230VAC,Full load
THD(full load) <10%@230VAC, Full load
AC Current(max) 0.12Amax@230VAC
Standby power <0.5W
Inrush Current(max) Cold start,15A(twidth=14us measured at 50% Ipeak)@230VAC
O u t p u t
Current(mA)/Voltage (VD
Power(W)
C)120mA/9-42VDC/5.04W 150mA/9-42VDC/6.3W 180mA/9-42VDC/7.56W 200mA/9-42VDC/8.4W
240mA/9-42VDC/10.1W 270mA/9-42VDC/11.34W 300mA/9-40VDC/12W 350mA/9-34VDC/11.9W
Ripple Current <3% C u r r e n t S e l ec t i on T a b l e
Remark: Function default setting is: 120mA (@switch are all
OFF state)
Channel 2
Current Tolerance ±5%
No load output voltage 50V Max
Turn on delay Time <1s, at230Vac
F u n c t i o n
Dimming Type DALI /Touch DIM
Dimming Range 1%-100% Dimming to off
color temperature 3000k-6000k
P r o t e c t i o nShort Circuit Close output, recovers automatically after fault removed
Over Load When the output voltage is exceeded, the output current decreases and, recovers automatically when
the load is reduced.
over Voltage Close output, recovers automatically after fault removed
Safety& E M C
Surge L-N:1KV
Withstand Voltage I/P-O/P: 3000VAC/1min/5mA
DALI Standard IEC 62386-101: 2014, IEC 62386-102: 2014IEC 62386-209: 2009, DALI 1.0
Safety Standards IEC/EN61347-1,IEC/EN61347-2-13,GB19510.1,GB19510.14,
EMC Eission EN50515,EN61000-3-2 Class C,IEC61000-3-3,GB/T17743
EMC Immunity EN61000-4-2,3,4,5,6,8,11 EN61547,GB17625.1
O t h e r s
Working Temp. -20℃~50℃
Storage Temp., Humidity -40℃~85℃, 20-90%RH
tc 80℃
Material PC
IP Rating IP20
Lifetime 50,000h@tc℃:70
Warranty Condition 5 Years
Switch Cycle >25,000 times
Packing(weight) Net weight: 125g±5%/PCS; 50PCS/Carton; 6.65kg±5%/Carton; Carton Size319*254*136mm(L*W*H)
Dimension 150*43*29mmL*W*H
120mA 150mA 180mA 200mA 240mA 270mA 300mA 350mA
9-42V 9-42V 9-42V 9-42V 9-42V 9-42V 9-40V 9-34V
DALI Constant Current Dimming Driver2 9
43
32.5
25.0
150.0
140.5
90.5
D i m e n s i o n ( m m ) D A L I W i r i n g
P u s h D I M ( T o u c h D I M ) D i a g r a mD A L I D i a g r a m
C a u t i o n s
1.This product should be installed by qualified personnel.
2.This product is non waterproof, need to avoid sun and rain.In case of outdoor use, please ensure it is mounted in a water proof enclosure.
3.Good heat dissipation conditions extend product life. Please install the product in a well-ventilated environment.
4.Please make sure LED power supply output voltage, current is used to meet the product requirements.
5.Please ensure that adequate sized cable is used from the controller to the LED lights to carry the current. Please also ensure
that the cable is secured tightly in the connector.
6.Due to safety concerns, PVC or rubber cord of 0.75-² 1.5mm is recommended for input and output terminal(s)(excluding
signal terminals). Flat power cord is not suitable.Ensure all wire connections and polarities are correct before applying power
to avoid any damages to the LED lights.
7.In case of malfunction, do not repair it yourself.
The contents of this manual are updated without prior notice. If the function of the product you are using is inconsistent with the instructions, the function of the
product shall prevail.Please contact us if you have any questions .
0
120 40 60 80 100 120 140 160 180 200 220 240 254
80
60
40
20
100
0.4
0.3
0.2
0.1
0
1 1 0 20 30 40 50
DALI Dimming Level
Outp
utC
urr
ent(
%)
D e r a t i n g C u r v e E f f i c i e n c y C u r v e
100
Load(%
) 80
60
40
20
0-20 -10 0 10 20 30 40 50 60
Ambient Temperature(℃)
DALI Signal Input
DALI Master
LN
Lamp
50/60Hz
ColourSWITCLH
Push DIML220-240VN
N L
CS
DA2
DA1/N
DA
LI
INP
UT
LED+
LED+
WW -
CW -
输出
LN
CS
DA2
DA1/N
DA
LI
INP
UT
LED+
LED+
WW -
CW -
220-240V 220-240V
Remark: Only use open push button without indicator light. Maximum cable length between each Unit: 20 meters.
P u s h D I M / C o l o e r S w i t c h
1. Press and hold the push DIM switch for 8s or more to enter the push dimming mode.
2. Press the push DIM switch briefly to turn on or off the lamp and return to the last memory state.
3. Press and hold the push DIM switch for dimming, stop at the current brightness when releasing, and adjust in the opposite direction every
4. Double click the push DIM switch to turn on the lamp to the brightest and cool light (this function is also used to adjust the consistency of
multiple power supplies in the same circuit)
5. Colour switch is valid only after entering push DIM mode.
6. Press colour SWITCH briefly to set the color temperature mode, with 9 values between 2,700 and 6,500K.
7.Long press Colour SWITCH can continuously adjust the color temperature. Every long press, the color temperature will be adjusted in
the opposite direction, with the color temperature range of 2700-6500K
8. Double click colour switch, turn on the lamp to the brightest, cold light (this function is also used to adjust the consistency of multiple
power supplies in the same circuit)
DALISignal
DA2
DA1/N
CS DA
LI IN
PU
T CW -
LED+
LED+
WW -输出
90%
85%
80%
75%
70%
230V/50Hz
65%
60%55%
50%100% 90% 80% 70% 60% 50% 40% 30% 20% 10%
Load(%)
Eff
.(%
)
Dimming Curve
Model EUP200AD-1H24V-0
Input
Efficiency >92%@230VAC,Full load
Voltage 220VAC-240VAC
Frequency Range(Hz) 50/60Hz
Power Factor ≥0.95@115VAC,Fullload
THD(full load) <10%@230VAC, Full load
AC Current(max) 1Amax@230VAC
Inrush Current(max) Cold start,27A(twidth=650us measured at 50% Ipeak) @230VAC
Output
Current / Voltage / Power 8.3A/24VDC/200W
R & N(Max) 400mVp-p
Channel 1
Voltage Accuracy ±3%
FunctionDimming Type DALI/Touch DIM/1-10V/Adjustable resistance /PWM
Dimming Range 0.1%-100% Dimming tooff
Protection
Overvoltage Close the output, restart to recover since fault condition is removed for 10s
Overtemperature Close the output, restart to recover since fault condition is removed for 10s
Short Circuit Hiccup, recovers after fault condition is removed
Safety
& EMC
Surge L-N:1KV
Withstand Voltage I/P-O/P: 3000VAC/1min/5mA
DALIStandard IEC 62386-101: 2014, IEC 62386-102: 2014; IEC 62386-207: 2009, DALI1.0
Safety Standards EN61347,GB19510
EMC Eission EN50515, EN61000-3-2
EMC Immunity
Working Temp. -20℃ ~5O℃
Storage Temp., Humidity -40℃ ~85℃ 20-90%RH
tc 90℃
Material Metal
OthersIP Rating IP20
Lifetime 50,000h@tc:80
Warranty Condition 5years
SwitchCycle >100,000 times
Packing(weight) Net weight: 860g±5%/PCS; 10PCS/Carton;9.1kg±5%/Carton; Carton Size: 333*268*150mm(L*W*H)
Dimension 310*60*45mm(L*W*H)
DALI&0/1-10V Constant Voltage Dimming Driver
UNIP200AD-1H24V-0 (Product No.:100200011101)
Summary
UNIP200AD-1H24V-0 is a constant voltage mode output LED driver. This driver complies
with DALI standard protocol IEC 62386,and provides multiple dimming function(DALI,1-10V
active signal ,PWM,adjustable resistance, and Touch DIM) to achieve a smooth dimming effect.
ProductFeatures
·Single channel constant voltage output
·Support a variety of dimming mode(DALI/1-10V active signal/adjustable resistance/PWM/Touch DIM)
·High range of input voltage 220VAC ~ 240VAC
·Built-in active PFC function
·Dimming effect smooth, no flicker
·Over temperature protection; Over voltage protection; Short circuit protection
·Suitable for indoor LED lighting application, such as LED strips, spot light, wall
washer,and so on
Technical Paramaters
Dimension(mm)
4.2
60 45
.3
310
300
4 5
Application
Wall Washer LED Strip Light LED Tube Underground Light AR111 Venture Light
DALI&0/1-10V Constant Voltage Dimming Driver
DALI Wiring
※ The contents of this manual are updated without prior notice. If the function of the product you are using is inconsistent with the instructions,
the function of the product shall prevail.Please contact us if youhave any questions .
Remark: Only use open push button without indicator light. Maximum cable length between each Unit: 20 meters.
Push DIMFunction
1.Press the Push DIM(TouchDIM)switchfor 8s or more,the drivercan be controlledviaPush DIMswitch.
2.Short pressthe Push DIM(TouchDIM)switch (<0.5s)tocontrol the lampon or off.
3.Long pressthe Push DIM(TouchDIM)switch (>0.5s)todim the brightness of light.The dimmingdirectionwillchange everytimeafter pressing switch.
4.Double-click the Push DIM(TouchDIM) switch (<0.3s), thenall lamps connected on the devicewillbeset maximum brightness.
5.The brightness adjustment range is 1%-100%, and the light can be turned off through short pressing when doing the adjustment with long pressing
Push DIM (Touch DIM) switch.
6. With the Power off memory function, the power-down state will be recovered when power on again.
Cautions
1.This product should be installed by qualified personnel.
2.This product is non waterproof, need to avoid sun and rain.In case of outdoor use, please ensure it is mounted in a water proof enclosure.
3.Good heat dissipation conditions extend product life. Please install the product in a well-ventilated environment.
4.Please make sure LED power supply output voltage, current is used to meet the product requirements.
5.Please ensure that adequate sized cable is used from the controller to the LED lights to carry the current. Please also ensure that the cable is secured tightly inthe connector.
6.Due to safety concerns, PVC or rubber cord of 0.75-2.5mm² is recommended for input and output terminal(s)(excluding signal terminals). Flat power cord is not suitable.Ensure all wire connections and polarities are correct before applying power to avoid any damages to the LED lights.
7.In case of malfunction, do not repair it yourself.
Push DIM(Touch DIM) DiagramDALIDiagram
Dimming Curve
DALIMASTER
L
N
0/1-10V Signal Input
L
N
DALI Curve 0/1-10V Curve
01
20
40
60
80
100
120
0.4
0.3
0.2
0.1
0
1 10 20 30 40 50
20 40 60 80 100 120 140 160 180 200 220 240 254
DALI Dimming Level
Out
putC
urre
nt(%
)
DALI Driver 1 LED+ LED-
DADAL N
DALI Driver 1 LED+ LED-
DADAL N
DALI Driver 1 LED+ LED-
DA DA L N
Push DIM Panel(Touch DIM)N L
861
861
861
12V/24V
861
861
861
12V/24V
861
861
861
12V/24V
DALI Driver 1 LED+ LED-
DA DA L N
DALI Driver 1DADA LED+
LED-L N
DALI Driver 1DADA LED+
LED-L N
LN
DALIController
861
861
861
12V/24V
861
861
861
12V/24V
861
861
861
12V/24V
100
80
60
40
20
0
0 5 9 14
18
23 27
32
36 41
45
50 54
59
63
68 72 77
81
86
90 95
99
Input Signal(%)
Out
putV
olta
ge(%
)
DALI6002E1
Features:
12-24V DC
PWM output current : MAX 10A/CH
DALI Digital control input, Dimming control LED module
Addressing output channel
Support Touch DIM function, and can be dimmed manually
Dimming range is from 0-100% (LED Will start from 1% )
Used for DC Power supply
Short circuit protection, Over load protection
Security level : 2
Two channels 12-24VDC constant voltage output
Model: DALI6002E1
Technical parameter:
Parameter Min.* Nom.* Max. Unit
Input voltage range 12 12-24 24 Vdc
Touch DIM AC input voltage range 5 - 290 VAC
Touch DIM AC input voltage frequency range 45 - 65 Hz
12-24 V DC Input current - - 10 A/ ch
Output power 0.1 2 x120-240 2 x240 W
Output voltage 12 12-24 24 Vdc
Output current - - 10 A/ ch
Peak current - - 11.5 A/ ch
Dimming control DALI definition IEC62386
Out casing temp - - 70 ℃
Surrounding temp -20 - 50 ℃
Protection Short circuit protection
Overload protection
*It’s available in 25℃ indoor
Size (mm)
Connecting:
Touch DIM function instructions:
1) Press the Touch DIM switch for 8s or more,the driver can be controlled via Touch DIM switch.
2) Short press the Touch DIM switch (<0.5s) to control the lamp on or off.
3)Long press the Touch DIM switch (>0.5s) to dim the brightness of light. The dimming direction will change every
time after pressing switch.4) Double-click the Touch DIM switch (<0.3s), then all lamps connected on the device will be set maximum brightness.
5)When the light being turned off, long press the Touch DIM switch can turn on the light and adjust the brightness
according to the dimming direction.
6)The brightness adjustment range is 1%-100%, and the light can be turned off through short pressing when doing the
adjustment with long pressing Touch DIM switch.
7) With the Power off memory function, the power-down state will be recovered when power on again.
Product installation notes:
1)Remark: DALI and Touch DIM functions cannot be used simultaneously, which can be controlled respectively by using DALI controllers or the equipments with Touch DIM function2) Please read the connecting instruction picture before installation3) Please use the complete set of product according to the provided specification
4)Please firstly pressure the cap end down in wire connecting process, then insert the thread of wire, and lastly check the wire is or not insert firmly5) Please check the connecting method is correct or not before connecting the power
DALI wiring diagram:
TouchDIM wiring diagram:
FunctionDescription
Dimension(mm)
WiringDiagram
Model DALI-R01CCT
Input Voltage Supplied Via Dali Bus
Input Current 24mA
Control Signal DALISignal
Panel colorIvory-white
W H DPanel size 86*86*44mm( * * )
Packing size 104*104*52mm( * *)
G.W. 140g℃
Working temp. -10~55
Relative humidity 20-90%RH
60
60
82.6
82.6
86
18 24
1.Color temperature / brightness mode switching, long press the knob, hear a drop, that is, switch from one mode toanother
2.Adjust the color temperature, enter the color temperature adjustment mode, and turn the knob to adjust the colortemperature.
3.Brightness adjustment, enter brightness mode, turn knob to adjust brightness4. In the color temperature or brightness mode, press the knob briefly to complete the on
/ off operation of the lamp.5. Power down saving function, after the device is powered down, the color temperature /
brightness command before power-off will be automatically sent to Dali bus when poweron again
6. Thebuzzer sounds and mute can be set byturningthe dial switch7.Directaddress control/ multicast/ broadcast comprehensive coverage.
OperatingInstructions
Connect dali-r01cct to Dali bus, set S1 and S2 to specified address. Press the knob for a short
time to switch on and off the lamp, and press the knob for a long time to switch the
brightness and color temperature modes.
In brightness mode: turn the knob clockwise to increase the brightness until the buzzer
does not sound the maximum, and turn the knob counterclockwise to decrease the
brightness until the buzzer does not sound the minimum.
In color temperature mode: turn the knob light anticlockwise to warm the color, until the
buzzer does not soundthewarmest, turntheknob light clockwise tocool thecolor, until the
buzzer does not sound the coldest.
The Setting of address S2 is shown in the following table:
Encode 0 1 2 3 4 5 6 7 8 9 A B C D E F
Function Single Address Group Radio Single Address Group Radio
Address S2*16+S1 S1 / (S2-6)*16+S1 S1 /
Sound Sound NoSound
Description: S1/S2 is the address dial switch.
DALI1
DALI2
DALI Bus
DALI2 DALI1
DALI PowerSupply
DALI1 DALI2
DLE
AD
LIDriver
DALIDimmer
DALI-R01CCT
ProductFeatures
· Supports adjustment of brightness and colour temperature.· Meet DALI Protocol IEC62386-207· ABS material, high flame retardant· Fashion, and easy to use· Can be installed in the wallbox· Suitable for ELV dimming driver, incandescent lamps, halogen lamps and other loads· Installation in appliance box to DIN 49073 , used in the study, bedroom, restaurant, bars
and other places need dimmingcontrolTechnical Parameters
InstallationGuide
1. Mount an electrical box inside the wall
S2 S1 DALI1 DALI2
DALI Dimmer
DALI-R01CCT
Tunable
White
DALIDimmer
2. To separate the panel and the back cover of the controller with a screwdriver along
the gap of the back cover.
3. Connect the wires according to the
“Wiring Diagram”
5.To buckle the glass panel to the bottom box.
4. To put the back cover on the electrical box and fix it with the screw.
Caution
1.Connect the load wire at first, then connect the power wire; Please ensure short circuit can not occur between wires before you turn on the power.
2.Please check the input voltage and frequency range, it may burn out the dimmer once exceed the voltage or frequency range.
DALI-130
DALI BUS Power Supply
SHANGHAI EUCHIPS INDUSTRIAL
CO.,LTD
Product Features
·Meet DALI Protocol IEC62386
·Output current up to 250mA Max
·Support two installation methods of rail and screw
fixing
·Support over current protection
·LED indicator light indicate status
Technical Parameters
Dimension(mm)
Cautions
WiringDiagram
Model DALI-130
Input voltage 220-240VAC
Input frequency 50/60Hz
Output voltage 16V+5%
Output current 250mA
Output power 4W
Working temp -20-50?
N.W. 71g
G.W. 105g
Product size 111*35*67mmCL*W*H3
Packing size 354*234*232mmCL*W*H3/60Pcs/Carton
Recommended wire size 1.5-2.5mm2
1.When using DALI-130
and DALI master
controller
simultaneously, you must
ensure that the polarity
connection of the DALI
signal is correct. .
2.Individual DALI circuits must not exceed 250mA,
the number of drivers andcontrollers shall not exceed64.
3.Usually, the current
consumption of each DALI
power supply is 2 mA, with
64 individual addresses this
will consume 128mA. The
remaining part is used to
supply the DALI controller
without built-in power
supply (including DALI
panel, DALI Group / scene
Material Cross-sectional
area /mm2
Wires length/m Material Cross-sectional
area /mm2
Wires length/m
2 5 ? 5 0 ? 7 5 ? 2 5 ? 5 0 ? 7 5 ?
Copper
0.14 31 28 26
Aluminium
0.14 19 17 16
0.50 112 102 93 0.50 68 62 57
0.75 168 153 140 0.75 102 93 86
1.00 224 204 187 1.00 136 125 115
1.50 300 300 281 1.50 205 187 172
2.00 300 300 300 2.00 273 250 230
2.50 300 300 300 2.50 300 300 280