Underwriters Laboratories Inc. - ITU: Committed to … Type: Satellite GSM Dual Phone Model Number:...

UL Korea, Ltd A not-for-profit organization dedicated 33rd FL, Gangnam Finance Center, 737 to public safety and committed to Yeoksam-dong, Gangnam-gu, Seoul quality service for over 100 years 135-984 Korea Tel: +82.2.2009.9000, Fax:+82.2.2009.9405

Underwriters Laboratories Inc.

www.ul.com/emc www.ulk.co.kr

Project: 11CA49640

File: MC16807

Report: 11CA49640-CE-EMC

Date: October 28, 2011

Model: XT DUAL

CE-R&TTE Directive Electromagnetic Compatibility Test Report

For

Satellite GSM Dual Phone

Asia Pacific Satellite communications Inc.

9FL, Lotte IT Castle 2-Dong, #550-1,Gasan-Dong, GeumCheon-Gu, Seoul, Korea, 153-768

Copyright 2005 Underwriters Laboratories Inc.

Underwriters Laboratories Inc. authorizes the above-named company to reproduce this Report provided it is reproduced in its entirety.

Only those products bearing the UL Mark should be considered as being covered by UL.

Project Number: 11CA49640 File Number MC16807 of 72 Model Number: XT DUAL

UL Korea, Ltd. 33rd

FL, Gangnam Finance Center, 737 Yeoksam-dong, Gangnam-gu, Seoul 135-984 Korea Tel: +82.2.2009.9000, Fax:+82.2.2009.9405 Report Version 1.2 June-06,2007


Summary of Test Results:

The following tests were performed on a sample submitted for evaluation of compliance with ETSI EN 301 489-1 V1.8.1, ETSI EN 301 489-7 V1.3.1, EN 301 489-17 V1.3.2 and EN 301 489-20 V1.2.1.

Test #

Test Name Test Requirement/Specification

Compliant Not Compliant See Remark

1 Conducted emissions on Mains power port X - -

2 Radiated emission X - -

3 Harmonic current emission - - 1)

4 Voltage fluctuation and flicker X - -

5 Electrostatic Discharges (ESD) X - -

6 RF electromagnetic field X - -

7 Fast transients immunity X - -

8 Surges immunity X - -

9 RF conducted continuous immunity X - -

10 Power frequency magnetic field immunity - - 1)

11 Voltage dips and short interruption X - -

Remarks: 1) Not applicable to this EUT. 2) Modifications to EUT required for compliance: None. 3) Purpose of Application : This application is to verify the compliance to the essential requirements of the harmonised standards applied to the original assessment due to the minor change of components. Manufacturer has declared the details of change and provided as the reference of this assessment. The change details is shown in the separate declaration statement.

Conclusion: The tests listed in the Summary of Testing section of this report have been performed as a witness testing and the results recorded by UL Korea Ltd. in accordance with the procedures stated in each test requirement and specification. The test list was determined by the Applicant as being applicable to the Equipment Under Test. As a result, the subject product has been verified to comply or not comply as noted in the Summary of Testing with each test specification. The test results relate only to the items tested. The equipment under test has

Met the technical requirements Not met the technical requirements

Tested by Jeawoon Choi, Senior Project Engineer

Reviewed by Kyungyong Kim, WiSE Manager

Conformity Assessment Services - 3014ASEO Conformity Assessment Services - 3014ASEO UL Korea Ltd. UL Korea Ltd. October 28, 2008 October 28, 2008


UL Korea, Ltd. 33rd



Test Report Details Tests Performed By: UL Korea Ltd. 33rd FL. GFC Bldg. 737 Yeoksam-dong,

Kangnam-ku, Seoul, 135-984, Korea Test Site: DigitalEMC Co., Ltd. 683-3, Yubang-Dong, Cheoin-Gu, Yongin-Si, Gyeonggi-Do, 449-080, Korea The test facility was deemed to have the environment and capabilities necessary to

perform the tests included in the test package. Applicant: Asia Pacific Satellite communications Inc. 9FL, Lotte IT Castle 2-Dong, #550-1, Gasan-Dong, GeumCheon-Gu, Seoul, Korea,

153-768

Applicant Contact: Young-Soo, Lee / Junior Engineer – R&D Center Phone: +82 2-2026-7788 E-mail: [email protected]

Manufacturer: Asia Pacific Satellite communications Inc. 9FL, Lotte IT Castle 2-Dong, #550-1, Gasan-Dong, GeumCheon-Gu, Seoul, Korea,

153-768

Product Type: Satellite GSM Dual Phone

Model Number: XT DUAL

Trademark

Product standards: ETSI EN 301 489-1 V1.8.1_ EMC standard for radio equipment and services; Part 1: Common technical requirements

ETSI EN 301 489-7 V1.3.1 _Part 7: Specific conditions for mobile and portable radio and ancillary equipment of digital cellular radio telecommunications systems ETSI EN 301 489-17 V1.3.2_Part 17: Specific conditions for 2,4 GHz wideband transmission systems, 5 GHz high performance RLAN equipment and 5,8 GHz Broadband Data Transmitting Systems ETSI EN 301 489-20 V1.2.1_Part 20: Specific conditions for Mobile Earth Stations (MES) used in the Mobile Satellite Services (MSS)

Sample Serial Number: N/A

Sample Receive Date: October 12, 2011 Testing Start Date: October 12, 2011 Date Testing Complete: October 24, 2011 Test Report Date: Overall Results: Compliant

UL Korea Ltd. reports apply only to the specific samples tested under stated test conditions. All samples tested were in good operating condition throughout the entire test program. It is the manufacturer's responsibility to assure that additional production units of this model are manufactured with identical electrical and mechanical components. UL Korea Ltd. shall have no liability for any deductions, inferences or generalizations drawn by the client or others from UL Korea Ltd. issued reports.


UL Korea, Ltd. 33rd



Report Directory 1. GENERAL PRODUCT DESCRIPTION ________________________________________________________ 5

1.1 REPORT REVISION HISTORY ________________________________________________________ 5

1.2 EQUIPMENT DESCRIPTION __________________________________________________________ 5

1.3 EQUIPMENT (EUT) CONFIGURATION ________________________________________________ 5

1.4 TECHNICAL DESCRIPTIONS AND DOCUMENTS: ______________________________________ 5

1.5 TECHNICAL SPECIFICATION: _______________________________________________________ 6

1.6 EQUIPMENT MARKING PLATE: ______________________________________________________ 8

2. TEST CONDITION _________________________________________________________________________ 8

2.1 EQUIPMENT USED DURING TEST: ___________________________________________________ 8

2.2 INPUT/OUTPUT PORTS: ______________________________________________________________ 9

2.3 POWER INTERFACE: ________________________________________________________________ 9

2.4 EUT INTERNAL OPERATING FREQUENCIES: _________________________________________ 9

2.5 EUT OPERATION MODES: ___________________________________________________________ 9

2.6 TEST CONFIGURATION: ____________________________________________________________ 10

2.7 PERFORMANCE ASSESSMENT ______________________________________________________ 11

2.7.1 GENERAL PERFORMANCE CRITERIA _______________________________________________ 11

2.7.2 PRODUCT SPECIFIC PERFORMANCE _______________________________________________ 11

2.8 SUMMARY OF TEST RESULT _______________________________________________________ 12

3. TEST CONDITION AND RESULTS __________________________________________________________ 14

3.1 CONDUCTED EMISSION TEST ______________________________________________________ 14

3.2 RADIATED EMISSION ______________________________________________________________ 25

3.3 VOLTAGE FLUCTUATIONS AND FLICKER __________________________________________ 45

3.4 ELECTROLECTROSTATIC DISCHARGE (ESD) : TEST WAS NOT PERFORMED _________ 48

3.5 RF ELECTROMAGNETIC FIELD IMMUNITY _________________ ________________________ 49

3.6 ELECTRICAL FAST TRANSIENTS ___________________________________________________ 54

3.7 SURGES ____________________________________________________________________________ 57

3.8 RADIO FREQUENCY, COMMON MODE ______________________________________________ 60

3.9 VOLTAGE DIPS AND INTERRUPTIONS ______________________________________________ 63

APPENDIX A. PRODUCT PHOTOS_EXTERNAL ______________________________________________ 65

APPENDIX B. PRODUCT PHOTOS_INTERNAL _______________________________________________ 70

APPENDIX C - ACCREDITATIONS AND AUTHORIZATIONS ____ ______________________________ 71

APPENDIX D - MEASUREMENT UNCERTAINTIES ___________________________________________ 72


UL Korea, Ltd. 33rd



1. GENERAL PRODUCT DESCRIPTION

1.1 Report Revision History

Revision Date Description Revised By Revision reviewed By

None Original - -

1.2 Equipment Description

Description

Thuraya XT DUAL is an advanced satellite phone using cutting edge technology. Its superiority is reflected in having three integrated technologies in one handset: satellite (SAT), GSM and GPS offering you an unmatched combination of quality and performance. Thuraya XT DUAL is a tri-band phone that allows operations on three different GSM networks: 900, 1800, 1900 MHz offering highest flexibility. In order to establish communication on SAT mode, there are a few points to consider: - The antenna should be pulled out to make or receive SAT calls. - While observing the indicator for SAT signal strength, move your phone to achieve the best connection quality. - SAT communication requires clear space without obstructions such as buildings, trees or mountains. - Try to direct the antenna of the Thuraya XT DUAL towards a Thuraya satellite if the signal strength is not sufficient.

1.3 Equipment (EUT) Configuration

Equipment type Manufacturer Model

Satellite GSM Dual Phone Asia Pacific Satellite communications Inc. XT DUAL

Ear Set I-sound HC-MYD-APS001

Travel Charger Ktec KSAS0100500200D5

Note: All the following EUT information has been provided by the applicant.

1.4 Technical descriptions and documents:

No. Document Title and Description

1 User’s manual

Note: The manufacturer provided the following document.


UL Korea, Ltd. 33rd



1.5 Technical Specification:

SAT Mode

Item Specification Comment

Transmitter frequency range(s) 1626.5~1660.5 MHz -

Channel Bandwidth 31.25 KHz -

Receiver frequency range(s) 1525~1559 MHz -

Transmitter power Max 2 W Typical 1.8 W

Radiated power (EIRP) Max 7 dBW Min 5.0 dBW

Intermediate frequency 246MHz Level -20 dBm

Frequency Accuracy Uncorrected: < ± 5ppm Corrected: < ± 0.006ppm

Kind of Baseband signal Voice / circuit data / packet data/ fax -

Kind of modulation (s) π/4 - CQPSK -

Data rate(s) Tx: 2.4Kbps /4.8Kbps/ 9.6Kbps /14.4Kbps

Rx2.4Kbps /4.8Kbps/ 9.6Kbps /60Kbps

FEC Convolution (1/2, 1/3, 1/4,1/5) -

Power supply (Battery Voltage) Typ. 3.7Vdc -

Note: All the technical data described above were provided by the manufacturer.

GSM Mode

Parameter / Frequency BAND GSM900 DCS1800

Transmitter frequency range(MHz) 880~915 1710 ~1785

Channel Spacing(kHz) 200 200

Receiver frequency range(MHz) 925 ~ 960 1805 ~ 1880

Transmitter power(dBm, Max) 33 30

Frequency Accuracy(Hz) +/-90 +/-180

Timeslot Period(us) 3.692 3.692

Kind of modulation (s) GMSK GMSK

Modulation Data Rate(kbit/s) 270.833 270.833

Frame period(ms) 4.615 4.615

Data rate(s) CSD RATE:2.4/4.8/9.6/14.4Kbps GPRS downlink max 85.6kbps GPRS uplink max 42.8kbps

CSD RATE:2.4/4.8/9.6/14.4Kbps GPRS downlink max 85.6kbps GPRS uplink max 42.8kbps

Time slot duration(us) 577 577

Power supply (Battery Voltage) Typ. 3.7Vdc


UL Korea, Ltd. 33rd



Bluetooth Mode

Item Specification

Carrier Frequency 2400MHz to 2483.5MHz (USA, Europe)

Modulation Method GFSK, 1Mbps, 0.5BT Gaussian

Maximum Data Rate Asymmtric: 723.2kbps/57.6kbps Symmetric: 433.9kbps/433.9kbps

Transmission Power Typ 1.0 dBm

Hopping 1600hops/sec, 1MHz channel space

Rx. Sensitivity (BER<0.1%) Typ. -83.0 dBm

Output Interface AUDIO, SPI, UART, PCM, USB

Baseband Crystal OSC 26MHz

Compliant Bluetooth Specification v1.1

Built in Memory Flash memory (4Mbit)

BC02 Bluetooth module Antenna Specifications

Frequency Range 2.4 ~2.485 GHz

VSWR 2.5 : 1 max.

Gain Avg. -3 dBi min.

Polarization Linear

Azimuth Beam Pattern Omni-directional

Impedance Nominal 50 Ω

Note: All the technical data described above were provided by the manufacturer.


UL Korea, Ltd. 33rd



1.6 Equipment Marking Plate:

2. TEST CONDITION

2.1 Equipment Used During Test:

Use* Product Type Manufacturer Model Comments

EUT Satellite GSM Dual Phone Asia Pacific Satellite

communications Inc. XT DUAL EUT

EUT Ear Set I-sound HC-MYD-APS001 EUT

EUT Travel Charger Ktec KSAS0100500200D5 EUT

SIM Universal Radio

Communication Tester R&S CMU200 -

SIM SAT TEST NATIONAL INSTRUMENT SAT TEST -

SIM BLUETOOTH TESCOM TC-3000B

AE Notebook LG ELECTRONICS INC. LGR51 -

Note: Use = EUT - Equipment Under Test, AE - Auxiliary/Associated Equipment. SIM - Simulator (Not Subjected to Test)


UL Korea, Ltd. 33rd



2.2 Input/Output Ports:

Port

# Name Type*

Cable Max. >3m Shielded Comments

1 Enclosure - - - -

2 DC Input DC 1.8 m Shielded -

3 USB Port I/O 1.5 m Shielded -

4 Ear set port I/O 1.2 m Unshielded -

Note 1: All the interface cables and Power Cable have been provided by the manufacturer Note 2: *AC = AC Power Port DC = DC Power Port N/E = Non-Electrical I/O = Signal Input or Output Port (Not Involved in Process Control) TP = Telecommunication Ports

2.3 Power Interface:

Mode #

Voltage (V)

Current (A)

Power (W)

Frequency (DC/AC-Hz)

Comments

Rated 100-240Vac 0.4 A 10 W AC 50-60Hz -

1 230 - - AC 50Hz -

2.4 EUT Internal Operating Frequencies:

Frequency (MHz) Description Frequency (MHz) Description

12 MHz Main Clock frequency 13 MHz Satellite frequency

2.5 EUT Operation Modes:

Mode # Description

1 GSM 900 Calling Mode While the charging adaptor and ear set were connected to the EUT, a communication link was set up with base station simulator.

2 GSM 900 Idle Mode GSM 900 Mode was set and keep stand-by status

3 BLUETOOTH Mode While the charging adaptor was connected to the EUT, a communication links were set up with base station simulator .

4 SAT Mode While the charging adaptor was connected to the EUT, a communication links were set up with base station simulator and Laptop PC .

Note : GSM 1900 mode of operation was not included in the test plan based on the engineering judgement by the manufacturer. The EMC performance for GSM 900 mode operation can be enough to presumption of conformity of this equipment.


UL Korea, Ltd. 33rd



2.6 Test Configuration:

Mode #

Communication link Mode

1

2

Note: Mode 1: GSM/BT communication link, Mode 2 : Satellite communication link

EUT

AC/DC Adapter

Communication Tester

(CMU200, TC-3000B)

Ear set

SAT TEST

EUT

AC/DC Adapter

Notebook

USB Cable DATA CABLE

Ear set


UL Korea, Ltd. 33rd



2.7 Performance Assessment

The establishment and maintenance of a communications link, the assessment of RXQUAL, and the assessment of the audio breakthrough by monitoring the speech output signal level, are used as performance criteria to ensure that all primary functions of the transmitter and receiver are evaluated during the immunity tests. In addition, the test shall also be performed in idle mode to ensure the transmitter does not unintentionally operate.

2.7.1 General Performance Criteria

Performance criteria for Continuous phenomena applied to Transmitters (CT) A communication link shall be established at the start of the test, and maintained during the test. During the test, the uplink speech output level shall be at least 35 dB less than the previously recorded reference levels, when measured through an audio band pass filter of width 200 Hz, centred on 1 kHz (audio breakthrough check). At the conclusion of the test, the EUT shall operate as intended with no loss of user control functions or stored data, and the communication link shall have been maintained. In addition to confirming the above performance during a call, the test shall also be performed in idle mode, and the transmitter shall not unintentionally operate.

Performance criteria for Transient phenomena applied to Transmitters (TT) A communications link shall be established at the start of the test. At the conclusion of each exposure the EUT shall operate with no user noticeable loss of the communication link. At the conclusion of the total test comprising the series of individual exposures, the EUT shall operate as intended with no loss of user control functions or stored data, as declared by the manufacturer, and the communication link shall have been maintained. In addition to confirming the above performance during a call, the test shall also be performed in idle mode, and the transmitter shall not unintentionally operate.

Performance criteria for Continuous phenomena applied to Receiver (CR) A communications link shall be established at the start of the test. During the test, the RXQUAL of the downlink shall not exceed the value of three, measured during each individual exposure in the test sequence. During the test, the downlink speech output level shall be at least 35 dB less than the previously recorded reference levels, when measured through an audio band pass filter of width 200 Hz, centred on 1 kHz (audio breakthrough check). At the conclusion of the test, the EUT shall operate as intended with no loss of user control functions or stored data, and the communication link shall have been maintained.

Performance criteria for Transient phenomena applied to Transmitters (TR) A communications link shall be established at the start of the test. At the conclusion of each exposure the EUT shall operate with no user noticeable loss of the communication link. At the conclusion of the total test comprising the series of individual exposures, the EUT shall operate as intended with no loss of user control functions or stored data, as declared by the manufacturer, and the communication link shall have been maintained.

2.7.2 Product Specific Performance

None


UL Korea, Ltd. 33rd



2.8 Summary of test result Vehicle mounted MES (V-MES) intended to be powered by the vehicle main battery Portable MES (P-MES) powered by a stand alone battery and external charger Fixed MES (F-MES) powered either by a DC or AC mains

Remark : The EUT is designed for portable use but all the testing has been performed with external chager connected.

There was no deviations from the technical specification of the applied standard Deviation from the technical specification has been observed and ascertained

Application Type Original Assessment Reassessment for engineering change Multiple listing

ETSI EN 301 489-1 and EN 301 489- 7/ -17/ -20 Test Requirements

Phenomenon Port Level Basic standard Verdict

Conducted emission,

0.15 to 30 MHz

AC power Ports Class B

EN 55022:1998+A1:2000 +A2:2003

Complied

Radiated emission,

30 to 1000 MHz

Enclosure Class B

EN 55022:1998+A1:2000 +A2:2003

Complied

Harmonic current emission

AC power Ports Class A EN 61000-3-2: 2001 N/A6

Voltage fluctuation and flicker

AC power Ports Met limit EN 61000-3-3: 1995 Complied

Electrostatic Discharges (ESD)

Enclosure Contact : ± 2,4 kV

Air : ± 2,4,8 kV

EN 61000-4-2: 1995 + A1: 1998 + A2: 2001

N/A5

RF electromagnetic field Enclosure 80MHz to 1000MHz, 1400MHz to 2700MHz 3V/m, AM 80%, 1kHz

EN 61000-4-3: 2002+A1:2002 Complied

Fast transients AC power Ports ± 1kV, 5/50ns, 5kHz EN 61000-4-4: 2004 Complied

Surges AC power Ports ± 1kV, 1.2/50µs, Line to Line

EN 61000-4-5: 1995+A1:2001 Complied

RF Continuous Conducted, Common mode

AC power Ports 3V/m, AM 80%, 1kHz EN 61000-4-6:1996+A1:2001 Complied

Voltage dips and short interruption

AC power Ports 0% of UT : 0.5 cycle, 0% of UT : 1 cycle, 70% of UT : 25 cycle, 0% of UT : 250 cycle,

EN 61000-4-11: 2004 Complied


UL Korea, Ltd. 33rd



Note: This product has been tested in accordance with the measurement procedures specified in ETSI EN 301 489-1 / EN 301 489-7 at the DigitalEMC Co., Ltd. and the test results has been shown to be complied with the EMC requirements specified in the standard above. N/A1 : Not tested because not required by used standard N/A2 : Test not applicable because port does not exists N/A3 : Test not applicable because port only for services N/A4 : Test not applicable because port lengths not longer than 3m N/A5 : Not tested because not required by customer N/A6 : For equipment with a rated power of ≤ 75 W, other then lighting equipment, no limits are specified in this edition of the standard. N/A7 : No test shall be made on equipment which is unlikely to produce significant voltage fluctuations or flicker. N/A8 : Tested with alternative port permitted in the standard.


UL Korea, Ltd. 33rd



3. TEST CONDITION AND RESULTS

3.1 Conducted Emission Test

TEST: Limits of mains terminal disturbance voltage

Method Measurements were made on a ground plane that extends 1-meter minimum beyond all sides of the system under test. All power was connected to the system through Artificial Mains Network (AMN). Conducted voltage measurements on mains lines were made at the output of the AMN.

Basic Standard EN 55022:1998+A1:2000+A2:2003

Parameters recorded during the test Laboratory Ambient Temperature 24 °C

Relative Humidity 42 %

- Frequency range on each side of line Measurement Point

Fully configured sample scanned over the following frequency range

150 kHz to 30 MHz AC power input

Limits - Class B

Frequency (MHz)

Limit (dBµV)

Quasi-Peak Result Average Result

0.15 to 0.50 66 to 56 Pass 56 to 46 Pass

0.50 to 5 56 Pass 46 Pass

5 to 30 60 Pass 50 Pass

EUT Configuration Settings:

Power Interface Mode #

(See Section 2.3)

EUT Operation Mode #

(See 2.5)

EUT Configurations Mode #

(See Section 2.6)

1 1,2,3,4 1,2

Conducted Emissions Test Equipment used:

Description Manufacturer Model Identifier Cal. Due

Test Receiver Rohde & Schwarz ESCI 100364 2012. 03. 08 LISN Rohde & Schwarz ESH2-Z5 828739/006 2012. 09. 30 LISN TTI LISN1600 197204 2012. 07. 02


UL Korea, Ltd. 33rd



Figure 1.1 Test Setup for Conducted Emissions

GSM, BT Mode_Operation mode 1,2,3


UL Korea, Ltd. 33rd



SAT Mode_Operation mode 4


UL Korea, Ltd. 33rd



Figure 1.2 Conducted Emissions Graph

GSM 900 TRAFFIC Mode


UL Korea, Ltd. 33rd




UL Korea, Ltd. 33rd



GPRS 900 IDLE Mode


UL Korea, Ltd. 33rd




UL Korea, Ltd. 33rd



BT MODE


UL Korea, Ltd. 33rd




UL Korea, Ltd. 33rd



SAT MODE


UL Korea, Ltd. 33rd




UL Korea, Ltd. 33rd



3.2 Radiated Emission

TEST: Limits for radiated disturbance

Method

Measurements were made in a 10-meter semi-anechoic chamber that complies to CISPR 16/ANSI C63.4. Preliminary (peak) measurements were performed at an antenna to EUT separation distance of 10-meter. The EUT was rotated 360° about its azimuth with the receive antenna located at 1, 2, 3 and 4 meter heights in both horizontal and vertical polarities. Final measurements (quasi-peak or average as noted) were then performed by rotating the EUT 360° and adjusting the receive antenna height from 1 to 4-meters. All frequencies were investigated in both horizontal and vertical antenna polarity, where applicable.

Basic Standards EN 55022:1998 + A1: 2000+ A2: 2003

Parameters recorded during the test Laboratory Ambient Temperature 24 °C

Relative Humidity 54 %

Frequency range Measurement Point


30 MHz – 1.0 GHz Enclosure

Limits – Class B

Frequency (MHz) Limit (dBµV/m)

Quasi-Peak Results

30 to 230 30 Pass

230 to 1000 37 Pass



(See Section 2.3)


(See 2.5)


(See Section 2.6)

1 1, 2, 3, 4 1, 2

Radiated Emissions Test Equipment:


EMI TEST RECEIVER

R&S ESU 100014 2012.01.20

Bilog Antenna SCHAFFNER CBL6112B 2737 2012.07.14

Horn Antenna SCHWARZBECK BBHA9120A 322 2012.04.13

Amplifier(22dB) H/P 8447E 2945A02865 2012.01.11

Pre Amplifier TSJ MLA-00108-B02-36 1518831 2012.01.11

Controller TOKIN 5905A N/A -

ANT.master TOKIN N/A N/A -


UL Korea, Ltd. 33rd



Figure 2.1 Test Setup for Radiated Emission

GSM/ BT Mode_Operation mode 1, 2, 3 30MHz ~ 1GHz


UL Korea, Ltd. 33rd



GSM/ BT Mode_Operation mode 1, 2, 3

1GHz ~ 6GHz


UL Korea, Ltd. 33rd



SAT Mode_Operation mode 4 30MHz ~ 1GHz


UL Korea, Ltd. 33rd



1GHz ~ 6GHz


UL Korea, Ltd. 33rd



GSM TRAFFIC MODE (30MHz ~ 1GHz)

902.4 MHz is TX frequency, 947.4 MHz is RX frequency


UL Korea, Ltd. 33rd




UL Korea, Ltd. 33rd



GSM TRAFFIC MODE (1GHz ~ 6GHz)

1800.000 MHz, 2700.000 MHz, 3612.500 MHz, 4512.500 MHz 5425.000 MHz are TX harmonics There are no emissions as above data plots


UL Korea, Ltd. 33rd




UL Korea, Ltd. 33rd



GSM IDLE MODE (30MHz ~ 1GHz)

947.4MHz is RX frequency


UL Korea, Ltd. 33rd




UL Korea, Ltd. 33rd



GSM IDLE MODE (1GHz ~ 6GHz)

There are no emissions as above data plots


UL Korea, Ltd. 33rd



BT TRAFFIC MODE (30MHz ~ 1GHz)


UL Korea, Ltd. 33rd




UL Korea, Ltd. 33rd



BT TRAFFIC MODE (1GHz ~ 6GHz)

2400.000 MHz are TX frequncy There are no emissions as above data plots


UL Korea, Ltd. 33rd




UL Korea, Ltd. 33rd



SAT MODE (30MHz ~ 1GHz)


UL Korea, Ltd. 33rd




UL Korea, Ltd. 33rd



SAT MODE (1GHz ~ 6GHz)

1637.500 MHz is TX frequency 3287.500 MHz, 4937.500 MHz are TX harmonics

There are no emissions as above data plots


UL Korea, Ltd. 33rd




UL Korea, Ltd. 33rd



3.3 Voltage Fluctuations and Flicker

TEST: Limits of voltage changes, voltage fluctuations and flicker

Method

This test consists on the measurement of voltage changes, voltage fluctuations and flicker which may be produced by equipment having an input current ≤ 16 A per phase, and intended to be connected to public low-voltage distribution systems. The equipment is tested under specified conditions of operation.

Basic Standard EN 61000-3-3:1995

Parameters recorded during the test Laboratory Ambient Temperature 23.0 °C

Relative Humidity 43.0 %



(See Section 2.3)


(See 2.5)


(See Section 2.6)

1 4 2

Test supply voltage specifications

Voltage ± 2 % of the nominal value

Frequency 50 Hz ± 0.5 %

Percentage total harmonic distortion Less than 3 %

Reference impedance (according to IEC 60725)

On phase 0.24 + j 0.15 Ω at 50 Hz

On neutral 0.16 + j 0.10 Ω at 50 Hz

Observation period (Tp) For Pst Tp = 10 minutes, For Plt Tp = 120 minutes

Limits

The value of Pst shall be not greater than 1.0 The value of Plt shall be not greater than 0.65 The value of d(t) during a voltage change shall not exceed 3.3 % for more than 500 ms The relative steady-state voltage change, dc shall not exceed 3.3 % The maximum relative voltage change dmax shall not exceed: a) 4 % without additional conditions b) 6 % for equipment which is: - switched manually, or - switched automatically more frequently than twice per day, and also has either a delayed restart (the delay being not less than a few tens of seconds), or manual restart, after a power supply interruption c) 7 % for equipment which is - attended whilst in use (for example : hair dryers, vacuum cleaners, kitchen equipment such as mixers, garden equipment such as mowers, portable tools such as electric drills), or - switched on automatically, or is intended to be switched on manually, no more than twice per day, and also has either a delayed restart (the delay being not less than a few tens of seconds) or manual restart, after a power supply interruption.


UL Korea, Ltd. 33rd



Test Equipment Used


POWER ANALYZER VOLTECH

INSTUMENT PM6000 100006700031 2012.07.12

Reference Impedance Network

NF CORPORATION

ES4152 424059 2012.09.30

CVCF NF

CORPORATION 4420 304935/337980 2012.03.08

Figure 3.1 Photo of test setup


UL Korea, Ltd. 33rd



Table 3.1 Voltage fluctuation and flicker test data of SAT Mode

Parameter Result Parameter Result

Pst Pass dc Pass

Plt N/A dmax Pass

d(t) Pass -


UL Korea, Ltd. 33rd



3.4 Electrolectrostatic Discharge (ESD) : Test was not performed

TEST: Electrostatic Discharge

Method Measurements were made on a ground plane that extends 0.5-meter minimum beyond all sides of the system under test and the minimum distance between the equipment under test and any laboratory walls or any other metallic surfaces shall be at least 1-meter. Air discharges were applied to non-metallic parts of the system. Contact discharges were applied to all accessible metallic parts. Discharges were also applied to the Horizontal and Vertical Coupling Planes, where applicable. Each discharge was applied at a rate of one (1) discharge per second.

Basic Standard EN 61000-4-2:1995+A2: 2001

Parameters required prior to the test Laboratory Ambient Temperature °C

Relative Humidity %

Parameters recorded during the test

Laboratory Ambient Temperature

Relative Humidity ％

Air pressure mbar

- Measurement Point

Fully configured sample subjected to the levels shown below.

Enclosure

Test Levels:

Discharge type Discharge Level (kV) Number of discharges per location (each polarity) Positive Positive Negative

Air – Direct 2, 4, 8 2, 4, 8 10

Contact – Direct 2, 4 2, 4 10

Contact – Indirect 2, 4 2, 4 10



(See Section 2.3)


(See 2.5)


(See Section 2.6)

ESD Test Equipment used:



UL Korea, Ltd. 33rd



3.5 RF Electromagnetic Field Immunity

TEST: Radio-frequency electromagnetic field Amplitude modulated

Method Measurements were made in a fully anechoic chamber and the indicated field strength was pre-calibrated prior to placement of the system under test. Tests were performed in both the horizontal and vertical polarities, where applicable. The antenna was placed 3 meters from the product under test. All sides of the EUT were investigated for anomalies.

Parameters recorded during the test Laboratory Ambient Temperature 21

Relative Humidity 46 ％


- Frequency range Measurement Point


80.0 MHz – 2,7 GHz Enclosure

Applied Field Strength:

Frequency (MHz) (V/m) Modulation

80 – 1000 3 80 % AM (1 kHz)

1400 – 2700 3 80 % AM (1 kHz)



(See Section 2.3)


(See 2.5)


(See Section 2.6)

1 1, 2, 3, 4 1, 2

Receiver exclusion band The lower frequency of the exclusion band is the lower frequency of the receive band of the EUT minus 6 % of that frequency.

The upper frequency of the exclusion band is the upper frequency of the receive band of the EUT plus 5 % of that frequency.

Transmitter exclusion band The exclusion band for transmitters extends three times the channel separation (3 × 200 kHz = 600 kHz) centred on the nominal operating frequency of the transmitter.


UL Korea, Ltd. 33rd



Radiated RF Field Immunity test equipment used:


SIGNAL GENERATOR HP 8648C 3847U02308 2012.07.26

POWER METEER HP 438A 3513U04164 2012.07.26

POWER AMPLIFIER PRANA MT100 1099 -

POWER AMPLIFIER PRANA DP70 1098 -

DUAL DIRECTIONAL COUPLERS

ATM CHP272L-40F-40R M185203-01 -


WERLATONE C39100-712 94894 -


WERLATONE C5086-712 94950 -

POWER SENSOR HP 8482A 3318A95113 2012.07.26

POWER SENSOR HP 8482A US38290170 2012.07.26

LOG-PER ANTENNE SCHWARZBECK VULP 9118 9118E890 -

Horn Antenna SCHWARZBECK BBHA9120A 556 -


UL Korea, Ltd. 33rd



Figure 5.1 Radiated RF Field Immunity Test Setup

Photos of the RF Field Immunity Test Setup_Operation mode 1,2,3

WITH EARMIC

WITHOUT EARMIC


UL Korea, Ltd. 33rd



Photos of the RF Field Immunity Test Setup_Operation mode 4

SAT MODE


UL Korea, Ltd. 33rd



Table 5.1 Result for the RF Field Immunity Test_GSM 900 Calling Mode

Test Location Polarity Results Test Location Polarity Results

Front Horizontal A Front Vertical A

Left Side Horizontal A Left Side Vertical A

Right Side Horizontal A Right Side Vertical A

Rear Horizontal A Rear Vertical A

Bottom side Horizontal A Bottom side Vertical A

Top side Horizontal A Top side Vertical A

Results Descriptions: A – Compliant – met the performance criteria Continuous phenomena applied to Transmitter and Receiver according to the clause 2.7.1 of this report

X - Not Performed.

Table 5.2 Result for the RF Field Immunity Test_BT Mode









X - Not Performed.

Table 5.3 Result for the RF Field Immunity Test_SAT Mode









X - Not Performed.


UL Korea, Ltd. 33rd



3.6 Electrical Fast Transients

TEST: Electrical Fast Transients

Method Measurements were made on a ground plane that extends 1-meter minimum beyond all sides of the system under test. Mains power tests were conducted with the product connected to a Coupling/Decoupling Network (CDN). One of each unique interface was tested for a period of one (1) minute per polarity.



Basic Standard EN 61000-4-4: 2004

Measurement Port

Fully configured sample subject to the levels shown below.

A.C Main Power Input Ports

Applied Level:

Application Point (kV) Repetition Frequency (kHz)

Input A.C. Power Port 1.0 5



(See Section 2.3)


(See 2.5)


(See Section 2.6)

1 1, 2, 3, 4 1, 2

Electrical Fast Transient Test Equipment used:


ULTRA COMPACT SIMULATOR

EMTEST UCS 500 N5 V1113109125 2012.03.21


UL Korea, Ltd. 33rd



Figure 6.1 Photo of Electrical Fast Transient test setup

Photos of the Electrical Fast Transient Test Setup_Operation mode 1, 2, 3

Photos of the Electrical Fast Transient Test Setup_Operation mode 4


UL Korea, Ltd. 33rd



Table 6.1 Results for Electrical Fast Transients_GSM 900 Calling Mode

Applied port Point of application Results Point of application Results

Main power input L1 A L1+L2 A

L2 A


X - Not Performed.

Table 6.2 Results for Electrical Fast Transients_BT Mode



L2 A


X - Not Performed.

Table 6.3 Results for Electrical Fast Transients_SAT Mode



L2 A


X - Not Performed.


UL Korea, Ltd. 33rd



3.7 Surges

TEST: Surges Immunity

Method Mains power tests were conducted with the product connected to a Coupling/Decoupling Network (CDN). The test voltage was increased from the lowest indicated level up to the maximum level. Five (5) positive surges and five (5) negative surges were applied at each of phases of the a.c. waveform: 0°, 90°, 180° and 270°. Each surge was applied 60 seconds after the previous surge. Signal and Telecommunications ports were subject to five (5) positive and five (negative) surges applied through the appropriate Coupling/Decoupling Network (CDN).




- Measurement Point

Fully configured sample subject to the levels shown below.

AC mains power input

Applied Level:

Application Point (kV) Required Surge Waveform

AC mains port

± 1.0 (Line to Line)

1.2/50µS Voltage (8/20µS, Current)

± 2.0 (Line to Ground)

1.2/50µS Voltage (8/20µS, Current)



(See Section 2.3)


(See 2.5)


(See Section 2.6)

1 1, 2, 3, 4 1, 2

Surge Immunity Test Equipment:



EMTEST UCS 500 N5 V1113109125 2012.03.21


UL Korea, Ltd. 33rd



Figure 7.1 Photo of Surges test setup

Photos of the Surges_Operation mode 1, 2,3

Photos of the Surges_Operation mode 4


UL Korea, Ltd. 33rd



Table 7.1 Results for Surges_GSM 900 Calling Mode

Mode of Application - Mains Level Polarity Result

Differential mode L to N 1.0 kV Positive A

Negative A


X - Not Performed.

Table 7.2 Results for Surges_BT Mode



Negative A


X - Not Performed.

Table 7.3 Results for Surges_SAT Mode



Negative A


X - Not Performed.


UL Korea, Ltd. 33rd



3.8 Radio Frequency, Common Mode

TEST: Radio-Frequency Common Mode

Method Measurements were made on a ground plane that extends 0.5-meter minimum beyond all sides of the system under test. The EUT was located 10cm above the reference ground plane and any associated I/O cables attached to the EUT were located between 30mm and 50mm above the ground plane. The indicated field was pre-calibrated prior to placement of the system under test.




- Frequency range Measurement Point


150 kHz to 80 MHz AC Main Power input Ports

Applied Level:

Frequency (MHz) (Vrms) Modulation

0.150 – 80 MHz 3 80 % AM (1kHz)

Supplementary information: Frequency step: 1 %, Dwell time at each frequency: 3 s


Power Interface Mode # (See Section 2.3)

EUT Operation Mode # (See 2.5)

EUT Configurations Mode # (See Section 2.6)

1 1, 2, 3, 4 1, 2

Conducted Immunity Test Equipment used:

Description H.P Model Identifier Cal. Due

Signal Generator H.P 8657B 3630U08728 2012.07.02

Power Meter H.P 438A 3048U02191 2012.07.02

Power Sensor H.P 8482A MY41090826 2012.09.30

Power Sensor Frankonia 8482A 3630U08728 2012.07.02

RF Power Amplifier (~230MHz, 75W)

TSJ FLL75 0072 N/A

CDN TSJ TSCDN-M2-16A 2008 2012.07.01


UL Korea, Ltd. 33rd



Figure 8.1 Photo of Radio Frequency, Common Mode test setup

Photos of the Radio Frequency, Common Mode test setup_Operation mode 1, 2, 3

Photos of the Radio Frequency, Common Mode test setup_Operation mode 4


UL Korea, Ltd. 33rd



Table 8.1 Results for Radio Frequency, Common Mode_GSM 900 Calling Mode

Point of application Coupling Results

AC Main power input Ports CDN M2 A


X - Not Performed.

Table 8.2 Results for Radio Frequency, Common Mode_BT Mode




X - Not Performed.

Table 8.3 Results for Radio Frequency, Common Mode_SAT Mode




X - Not Performed.


UL Korea, Ltd. 33rd



3.9 Voltage Dips and Interruptions

TEST: Voltage Dips and Interruptions

Method The product was subjected to voltage dips and interruptions. Testing was performed with the product connected directly to a generator capable of simulating the voltage drops and interrupts as described



Basic Standard EN 61000-4-11: 2004

- Measurement Point

Fully configured subjected to the levels indicated below. AC Mains Power Input port

Applied Levels:

Voltage Reduction Period (Cycles) Sync Angle (degrees)

30% 0.5 cycle 0, 180

60% 5.0 cycle 0, 180

≥95% 250 cycle 0, 180



(See Section 2.3)


(See 2.5)


(See Section 2.6)

1 4 2

Voltage dips and Short Interruption Test Equipment:



EMTEST UCS 500 N5 V1113109125 2012.03.21

MOTOR VARIAC EMTEST MV2616 V1113109126 2012.03.21


UL Korea, Ltd. 33rd



Figure 9.1 Photo of Voltage Dips and Interruptions test setup

Photos of the Voltage Dips and Interruptions test setup_Operation mode 4

Table 9.1 Results for Voltage Dips and interruptions _GSM 900 Calling Mode

Point of application Voltage Reduction Period (Cycles) Results

Mains power input 0% 0.5 cycle A

Mains power input 0% 1 cycle A



Results Descriptions: A – Compliant – met the performance criteria Continuous phenomena applied to Transmitter and Receiver according to the clause 2.7.1 of this report B – Compliant – During the interruption period, the LCD panel was getting brighter or turned on when the EUT was in energy saving mode.

X - Not Performed.


UL Korea, Ltd. 33rd



Appendix A. Product Photos_External

Front side

Rear side


UL Korea, Ltd. 33rd



Battery separated

AC/DC Adapter


UL Korea, Ltd. 33rd



AC/DC Adapter_LABEL

EARMIC


UL Korea, Ltd. 33rd



BATTERY


UL Korea, Ltd. 33rd



BATTERY_LABEL


UL Korea, Ltd. 33rd



Appendix B. Product Photos_Internal


UL Korea, Ltd. 33rd



APPENDIX C - ACCREDITATIONS AND AUTHORIZATIONS

KCC: Designated as a testing laboratory by Radio Research Laboratory in accordance with the Regulation on Designation of Testing Laboratory for Information and Communication Equipment. Registration No. : KR0034

KOLAS: Accredited by Korea Laboratory Accreditation Scheme (KOLAS) as Testing Laboratory in accordance with the provisions of Article 23 of the National Standards Act. These criteria encompass the requirements of ISO/IEC 17025:2006. For a scope listing search at http://kolas.kats.go.kr/WebApp/Main/Search/Search0010.aspx?CompanyNo=3793&AccreditNo=3663&BigID=03

FCC: Details of the measurement facilities used for these tests have been filed with the Federal Communications Commission’s Laboratory in Columbia, Maryland and accepted in a letter dated May 28, 2010 (Reg. No. 678747). As a Conformity Assessment Body (CAB), our organization is designated to perform compliance testing on equipment subject to Declaration Of Conformity (DOC) and Certification under Part 15 and 18 of the Commission’s Rules in a letter dated May 28, 2010.

VCCI: Accepted as an Associate Member to the VCCI. The measurement facilities detailed in this test report have been registered in accordance with Regulations for Voluntary Control Measures, Article 8. Registration Nos.: (Radiated Emissions) R-3385, (Conducted Emissions) C-1427.


UL Korea, Ltd. 33rd



APPENDIX D - MEASUREMENT UNCERTAINTIES

Test Item Measurement uncertainty

Conducted emission ± 4.43 dB, Note 1

Radiateded emission ± 3.47 dB, Note 1

Harmonic ± 7.10 %, Note 1

Fliker ± 7.66 %, Note 1

ESD At least a 95 % confidence

Radiated RF-electromagnetic field ± 1.38 dB, Note 1

Electrical fast transient/burst At least a 95 % confidence

Surge At least a 95 % confidence

Conducted RF field immunity ± 1.38 dB, Note 1

Magnetic Field At least a 95 % confidence

Voltage dips and short interruption At least a 95 % confidence

Note 1:Measurement uncertainty is calculated in according with LAB34(2002-08). The measurement uncertainty is given with a confidence of 95% with the coverage factor, k=2.

Underwriters Laboratories Inc. - ITU: Committed to … Type: Satellite GSM Dual Phone Model Number:...

Documents

Transcript of Underwriters Laboratories Inc. - ITU: Committed to … Type: Satellite GSM Dual Phone Model Number:...