UNC Respiratory Protection Program for Energy Services CoGeneration Facility Mechanical Maintenance...

UNC Respiratory Protection UNC Respiratory Protection Program for Energy Services Program for Energy Services

CoGeneration FacilityCoGeneration FacilityMechanical Maintenance Work UnitsMechanical Maintenance Work Units

Presented byPresented by

UNC-CH Environment, Health UNC-CH Environment, Health & Safety& Safety

Class ObjectivesClass Objectives• Introduction to the Respiratory Protection ProgramIntroduction to the Respiratory Protection Program• Review of General Work Operations -Respirator Review of General Work Operations -Respirator

UseUse• Review of Potential Health Hazards PresentReview of Potential Health Hazards Present• Review of Respirator Types Used Review of Respirator Types Used • Review Respirator Manufacturer Operating & Review Respirator Manufacturer Operating &

Maintenance Instructions Maintenance Instructions • Review Respirator Fit-Testing Procedures Review Respirator Fit-Testing Procedures • Complete Post-TestComplete Post-Test

IntroductionIntroduction

The University of North Carolina at Chapel Hill (UNC-The University of North Carolina at Chapel Hill (UNC-CH)CH)

Respiratory Protection Program describes written Respiratory Protection Program describes written policy andpolicy and

procedures for the use of respirators to protect the procedures for the use of respirators to protect the health ofhealth of

employees in accordance with the Occupational Safety employees in accordance with the Occupational Safety and and

Health Administration’s (OSHA) Respiratory Protection Health Administration’s (OSHA) Respiratory Protection

Standard, 29 CFR 1910.134 (General Industry Standard, 29 CFR 1910.134 (General Industry RespiratorRespirator

Standard).Standard).

Respirator Use: Maintenance Work Requirements

An evaluation was performed for the use of respirators at the CoGeneration (CoGen) Facility.

A review of the respiratory protection program was performed with CoGen site supervisors/superintendents at later dates.

The evaluation consisted of conducting a site visit to tour plant areas and to interview work unit supervisors and employees in areas where respirators are used. Our goal was to determine if the type of respiratory protection currently used is sufficient. Findings were shared with the Workplace Safety Manager and plant superintendents.

Based on the evaluation findings, respirators are stored and used at the CoGeneration facility for both general operations/maintenance work requirements and for emergency response use during emergency response situations.

This training module covers general operations/maintenance work requirements for respirator use, not emergency response use. Emergency Response use will be covered in a separate training module.


Findings: Only specific employees at the facility use and require respirators for general operations and maintenance work requirements.

Not all employees at CoGen need to be enrolled in the UNC-CH Respiratory Protection Program based on survey results.

Primarily Maintenance Mechanics (Boiler Mechanics) and Fuel Handlers (Coal & Ash Mechanics) have been issued and use respirators and are enrolled in the UNC-CH Respiratory Protection Program (RPP).


Respirators are properly stored inside a designated storage locker at the CoGen Plant. The respirators appeared to be in good material condition and are properly maintained.

Respirator Use: Maintenance Work Requirements Maintenance Mechanics (Bolier Mechanics) are issued North full face & half-face air purifying respirators (APRs) equipped with P100 filters and combination chemical cartridges for infrequent plant boiler cleaning and inspection operations. 3M 8511 N95 filtering facepiece respirators are also worn during part of this process.

The primary inhalation hazard is exposure to coal dust during the use of the plants Milling Machine and (Fly Ash) particulate matter from the coal burning process during the cleaning and inspection process of the boiler plant components. The respirators currently used by the Boiler Mechanics are acceptable and protective against coal dust and fly ash.

A half-face N95 filtering facepiece respirator is the recommended respirator for up to 10 times (x) the applicable Occupational Exposure Limit (OELs) for coal dust. The OELs are the OSHA permissible exposure limit (PEL) and the ACGIH Threshold Limit Value (TLV).

The following slide indicates a summary of work processes, potential health hazards, recommended respirators, filters and cartridges.


Boiler Mechanic Maintenance Respirator Recommendations

Work TaskWork Task Potential Potential HazardHazard

Minimum Minimum Respirator Respirator

RecommendedRecommended

Filters/Filters/Chemical Chemical

Cartridges Cartridges RequiredRequired

Inspecting & Cleaning out the

interior of the Plant Mills

Coal dust Disposable filtering facepiece (e.g. N95)

Either N, R, P, 95, 99, or P100 filters

When entering in the various areas of the

plant boilers to perform inspections,

cleaning, and maintenance work

Fly Ash Full face air purifying respirators

P100 filters

Replacing the baghouse filters; and opening the hoppers to inspect the filters

Fly Ash Disposable filtering facepiece (e.g. N95)


During “heavy” aerosol paint

operations and when cleaning plant

equipment

Organic vapors

*(caustic and acid when cleaning

caustic and acid tanks)

Full face air purifying respirators

Combination chemical cartridges;

*(acid gas when cleaning acid tanks)

Respirator Use: Maintenance Work RequirementsCoal dust health hazard information (from OSHA Health

GuidelinesLiterature):

Good industrial hygiene practices requires that engineering controls be used where feasible to reduce workplace concentrations of hazardousmaterials to the prescribed exposure limit.

However, some situations may require the use of respirators to control exposures in

accordance with OSHA guidelines. Conditions for respirator use (in accordance with

OSHA health guidelines) to control exposures to coal dust include:

Respirators must be worn if the ambient concentration of coal dustexceeds the prescribed exposure limits.

Respirators may be used: 1) Before engineering controls have been installed2) During work operations such as maintenance or repair activities that

involve unknown exposures3) During operations that require entry into tanks or closed vessels4) During emergencies


Routes of exposure for coal dust exposure can occur through inhalation,

ingestion, and eye contact.

The signs and symptoms of exposure to coal dust include:

Acute exposure: symptoms of inhalation of excessive amounts of coal dust

include coughing, wheezing, and shortness of breath.

Chronic exposure: Chronic exposure to coal dust may result in symptoms

of chronic bronchitis and emphysema. Coal dust causes coal workers’

Pneumoconiosis (CWP).

Complicated CWP is characterized by lesions consisting of a mass of

rubbery well defined black tissue that is often adherent to the chest wall.

This is associated with decrements in ventilatory capacity, low diffusing

capacity, abnormalities of gas exchange, low arterial oxygen tension,

pulmonary hypertension, and premature death.


Milling Machine Used to Crush Coal: Mechanics use N95 disposable respirators when inspecting/cleaning out the interior of the Plant Mills.

Respirator Use: Maintenance Work RequirementsFly-Ash Health Hazard Information:

Fly ash (one of several coal combustion products) is the finely divided

mineral residue resulting from the combustion of coal in electric generating

Plants.

Fly ash consists of inorganic, incombustible matter present in the coal that

has been fused during combustion into a glassy, amorphous structure.

Fly ash material solidifies while suspended in the exhaust gases and is

collected by electrostatic precipitators or filter bags.

Fly ash particles are generally spherical in shape and range in size from

0.5um (micrometers) to 100 um. Particles mostly consist of silicon

dioxide, aluminum oxide, and iron oxide. Fly ash may also contain trace

concentrations of heavy metals known to be hazardous to health in

sufficient amounts.


Excessive exposure to Fly ash dust can cause short term acute health

effects:

Eye Contact: Can cause abrasive irritation. Prolonged exposure can lead

to ulceration of the eye (this is why Full face APRs are used!);

Skin Contact: Can cause dermatitis in susceptible individuals (primarily

due to high PH, alkalinity).

Inhalation: Fly ash itself is classified as non-toxic. Health effects are

dependent on duration of exposure and the exposure concentration of the

chemical constituents present in Fly Ash (e.g. crystalline silica content and

heavy metals content which both can cause ill health effects, based on the

concentrations of these contaminants).


Full face Air Purifying Respirators (APRs) are also used when entering the

various areas of the boiler for protection against Fly-Ash from the coal

burning process.


Full face Air Purifying Respirators (APRs) equipped with P100 filters are

also used when entering the various areas of the boiler for protection

against Fly-Ash from the coal burning process.


Full face Air Purifying Respirators (APRs) equipped with P100 filters are

also used when entering the various areas of the boiler for protection

against Fly-Ash.

Cyclone


N95 filtering facepiece disposable respirators are used when replacing the

baghouse filters or when opening the hoppers to inspect the filters.

(Two Bag houses) (6-7 hoppers/per baghouse)


Employees should ensure the respirator is properly donned and a user seal

check is performed prior to entering the contaminated work environment.

Employees who handle or potentially come into contact with coal dust or

Fly Ash should follow proper personal hygiene procedures including

thoroughly washing hands, forearms, and face with soap and water before

eating, using tobacco products, using toilet facilities, or taking medicine.

If coal dust or fly ash contacts the skin, employees should wash the affected

areas with soap and water.


Maintenance Mechanics also use various aerosol chemical lubricants, cleaners, and aerosol can paints on occasion during maintenance and repair work. Respirators are sometimes worn during “heavy” aerosol can spray painting operations after refurbishing plant equipment and when cleaning plant equipment (e.g. process tanks, caustic and acid tanks).

The actual frequency and duration of these operations is variable. The primary potential hazard is exposure to organic vapors from the chemical ingredients and skin and eye exposure to caustic and acid chemicals. The respirator and chemical cartridges used (with combination chemical cartridges) is protective against organic vapors found in aerosol can spray paints, lubricants, and cleaners, and acid gasses.


When possible apply aerosol cans of paints, lubricants, cleaners, etc, in well-ventilated areas and remain upwind when possible.

Do not apply chemical products in poorly ventilated areas without the use of supplemental ventilation or respiratory protective equipment.

Ensure all other required personal protective equipment is worn (e.g. chemical protective gloves such as disposable nitrile gloves, eye protection such as safety glasses or chemical goggles).

Contact the EHS Industrial Hygiene Section at 3-2735/3-7313 during “heavy” spray operations and caustic and acid tank cleaning operations so these processes can be further evaluated.


Findings: Coal and Ash Mechanics also use respirators when unloading coal and limestone from railcars inside the coal unloading facility.


3M 8511 N95 filtering facepiece respirators are used by Coal and Ash Mechanics when unloading coal from railcars.

Additional full face and half face tight-fitting elastomeric respirators are maintained for use by some of the mechanics. Respirators are also used when sweeping and cleaning the railcar unloading area weekly as needed. However, contractors perform “heavy” cleaning operations.

Respirators are available and properly stored in a sanitary location at the coal and ash control room.


Engineering Controls Used to Minimize Dust Exposure: The railcar unloading area is equipped with a built in water sprinkler system to suppress dust when generated from the unloading process when needed.

There is a dust suppression activation panel both in the railcar unloading area and in the Coal and Ash Control Room (as pictured on the first page of this survey). Built in dust collection devices (additional engineering controls) are used in different areas of the coal transfer system.


Coal and Ash Mechanics have not recently unloaded limestone, because it is currently being trucked in and delivered via an enclosed process. Respirators are not generally worn during the coal unloading or transfer process, but they are available when needed.

The limestone unloading process (when using railcar) consists of positioning the loaded railcar in the facility, using a mechanical vibrator to shake material from the railcar. The material then settles into a hopper underneath and the material is then piped to the boiler plant.

Employees reportedly do not perform any physical removal or disturbance of the limestone, they remain in the control room during the unloading process and only have to be positioned in the railcar unloading process for short periods of time as needed during this process.

However, due to the dust levels, employees use respirators (3M 8511 N95 filtering facepiece respirators) when entering the railcar unloading area even for short periods of time.


Information from the National Institute of Occupational Safety and Health (NIOSH) about Limestone


Information from NIOSH about Limestone (Pure Calcium Carbonate):

Used to neutralize acidic coal air emissions.

Physical description: Odorless, white to tan powder.

Incompatible & reactive with acids, ammonium salts, fluorine, magnesium

Routes of exposure: Includes inhalation, ingestion, and/or eye contact

Signs and symptoms of acute exposure include: Irritation to the eyes,

skin, respiratory system, and cough.

Target Organs: Eyes, skin, respiratory system (However, it is claimed that

pure calcium carbonate does not cause adverse health effects including

pneumoconiosis).


Information from NIOSH about Calcium Oxide (CaO):

Sometimes CaO is a component of Limestone that is a mixture (0 - 43%)

Physical description: White or gray, odorless lumps or granular powder.

Incompatible with water (reacts with water to form calcium hydroxide).

Routes of exposure: Includes inhalation, ingestion, and/or eye contact

It is more hazardous compared to pure limestone

Signs and symptoms of exposure include: Irritation to the eyes, skin,

upper respiratory tract, ulcer, perforation of the nasal septum,pneumonitis, and dermatitis.

Target Organs: Eyes, skin, respiratory system


Findings: The National Institute of Occupational Safety and Health (NIOSH) recommends the use of any particulate respirator (N,R,P series) equipped for up to 10 times the OEL for calcium oxide.

The type of respirator used by Coal and Ash Mechanics (3M 8511 N95 filtering facepiece) is adequate if properly worn and properly fitted.


Continue to use a half-face N95 filtering facepiece respirator with safety glasses or chemical goggles when entering the railcar unloading area during the unloading of limestone from railcars. A half face or full face air-purifying respirator with N, R, or P100 filters may also be worn.

Ensure the respirator is properly donned and a user seal check isperformed prior to entering the area where limestone dust is being generated.

Employees should prevent skin and eye contact and wash affected skin areas if exposed. If eye exposure occurs, the eyes should be irrigatedimmediately by using an emergency eyewash or quick drench.

Recommend that this process (rail car unloading process of limestone or aragonite) be monitored by our IH Department when the process resumes in the near future.

Respirator Use: Maintenance Work RequirementsCoal and Ash Mechanic Maintenance Requirements

Work TaskWork Task Potential Potential HazardHazard

Minimum Minimum Respirator Respirator

RecommendedRecommended

Filters/Filters/Chemical Chemical

Cartridges Cartridges RequiredRequired

Unloading limestone from railcars*

*When entering the railcar unloading

area during unloading or physical removal of product

Limestone* (calcium carbonate &

potentially calcium oxide)

*Refer to the product MSDS for actual

constituents present & percentage

Disposable filtering facepiece (e.g. N95)

*A half or full face air purifying respirator

may also be used instead of a

disposable respirator


Performing maintenance

operations on the coal transfer

system or anytime visible high levels of coal dust are

generated(Need to change to

include new changes)

Coal dust

Disposable filtering facepiece (e.g.

N95)

*A half or full face air purifying

respirator may also be used instead of

a disposable respirator


Review of North 7600 Full Face Air Purifying Respirator Operating and Maintenance Instruction Manual

& 3M 8511/8211 Particulate N95

Instruction Manual

Review of Respirator Types Used

Review of Respirator Types Used North 7600 Series Full Face Air Purifying Respirator Operating

and Maintenance Instructions

Read and Understand Operating and Maintenance Instructions (handout provided)

General Warnings: This respirator is not to be used in Immediately Dangerous to Life or Health (IDLH) atmospheres.

An IDLH atmosphere is any atmosphere which has a concentration of any toxic, corrosive, or asphyxiant substance that poses an immediate threat to life, which would cause irreversible debilitating effects on health, or which would interfere with the ability to escape from a dangerous atmosphere.

IDLH is also an atmospheres where the concentration of the contaminant exceeds the respirator’s Maximum Use Concentration. This is where the concentration of the contaminant exceeds: 100 times the contaminant’s permissible exposure limit (the maximum permissible 8-hour time weighted average (TWA) concentration) established by applicable OSHA or other government regulations, or by NIOSH or ACGIH publications.

Review of Respirator Types UsedNorth 7600 Series Full Face Air Purifying Respirator Operating


Read and Understand Respirator Operating and Maintenance Instructions

(handout provided)

General Warnings: Do not use any air purifying respirator when conditions

prevent a good facepiece-to-face seal.

Examples of such conditions are:

The growth of beards, bangs, or sideburns which will pass between thefacepiece sealing area and the face;

The use of head or face coverings which contain materials which will pass

between the facepiece sealing area and the face (e.g. head bandannas).



Read and Understand Respirator Operating and Maintenance Instructions (handout provided)

Immediately leave the contaminated area if:

1) Breathing becomes difficult2) Dizziness or other distress occurs3) You smell, taste or sense irritation from the contaminants4) The air purifying element is equipped with an End-of-

Service-Life Indicator which has changed color to indicate expiration, or

5) The respirator becomes damaged.



Inspections: You are required to perform an inspection of the respirator prior to

use. Inspect all components of the respirator prior to use (e.g. straps, facepiece).

Periodic Seal Checks: Each time that the respirator is put on, before entering an

area containing hazardous atmospheres, and periodically while wearing the

respirator in the contaminated area, the respirator wearer should check the

effectiveness of the seal of the facepiece to the wearer’s face by carrying out a

negative and positive pressure seal check (turn to page 8 of instruction manual).

Positive Pressure Check Negative Pressure Check

http://images.google.com/imgres?imgurl=keats.admin.virginia.edu/images/os_positive_fit_test.jpg&imgrefurl=http://keats.admin.virginia.edu/os/resp.html&h=386&w=399&prev=/images%3Fq%3Dpositive%2Bfit%2Bcheck%26svnum%3D10%26hl%3Den%26lr%3D%26ie%3DUTF-8%26oe%3DUTF-8%26sa%3DN

http://keats.admin.virginia.edu/images/os_negative_fit_test.jpg



Review Page 6, pre-use instructions (facepiece, filters, assembling therespirator, corrective lenses)

Review Page 7-8, Putting on the respirator

Adjust the head straps

Spreading the head strap

Placing the facepiece on your head

Tightening the lower head straps

Tightening the upper head straps

Tightening the forehead head strap



Review Page 10,

Chemical cartridge change out schedule

Particulate filters

Taking off the respirator

Filter and cartridge replacement

Inspection

Storage

Review Page 11Cleaning and Sanitizing



Now, Practice the donning of the respirator and perform both a positive and negative user seal check.

You should feel comfortable with donning your respirator without assistance.

Your respirator fit-test score will depend on your ability to properly don the respirator and to obtain an appropriate fit

with the respirator.

Review of Respirator Types Used 3M 8511 Particulate N95 Respirator Operating and Maintenance

Instructions

Read and Understand Operating and Maintenance Instructions (handout provided)

The filtering facepiece respirator that you use has a NIOSH approval Rating ofN95: This means the respirator has been tested by NIOSH to provide at least

95%filtration efficiency against solid (particulate) and liquid aerosols that do notcontain oil.

Examples of ok uses include: particles generated from sweeping, sawing,bagging, or processing minerals, coal, iron, ore, wood, pollen, liquid, or non-oilbased particles from sprays that do not also emit oil aerosols or vapors.

This respirator may not be used for protection against gasses and vapors, oilaerosols, toxic metals (e.g. cadmium, lead), or ok particles in concentrations thatexceed 10 times their OSHA standard. Not to be used in IDLH atmospheres

(toxicand oxygen deficient atmospheres).


Instructions

Fitting Instructions: The following procedure must be followed each time

the respirator is worn (procedure is from the 3M 8511 instruction manual

handout):

1) Cup the respirator in your hand, with the nospiece at your fingertips, allowing the headbands to hang freely below your hand.

2) Position the respirator under your chin with the nosepiece up. Pull the top strap over your head resting it high at the top back of your head. Pull the bottom strap over hour head and position it around the neck below the ears.


Instructions

Fitting Instructions: The following procedure must be followed each time

the respirator is worn (procedure is from the 3M 8511 instruction manual

handout):

3) Place your fingertips from both hands at the top of the metal nosepiece. Using two hands, mold the nose area to the shape of your nose by pushing inward while moving your fingertips down both sides of the nosepiece.

4) Perform a User Seal Check prior to each wearing. To check the respirator-to-face seal, place both hands completely over the respirator and inhale sharply. Be careful not to disturb the position of the respirator. A negative pressure should be felt inside the respirator. If air leaks around the nose, readjust the nosepiece as described in step 3.

Respirator Fit-Testing Procedures

Employees at UNC-CH are required to receive a quantitative fit test

with the respirator that they will be using. The fit-testing will occur

prior to initial use of the respirator, or whenever a different respirator

facepiece (size, style, model, or make) is used, and at least annually

thereafter.

An additional fit-test is conducted annually thereafter and whenever

the employee, supervisor, the Environment, Health, and Safety,

or the UEOHC makes visual observations of changes in the employee’s

physical condition that could affect respirator fit. Such conditions include, but are not limited to, facial scarring,

dental changes, cosmetic surgery, or any obvious change in body

weight. Theemployee may select a different respirator if he/she does not

think therespirator fit is acceptable, even after passing the test.


Quantitative fit testing is an assessment of the adequacy ofrespirator fit by numerically measuring the amount of leakageinto the respirator. Testing is accomplished by modifying the face piece to allow sampling inside the face piece in thebreathing zone of the user, midway between the nose andmouth. This requirement is accomplished by using a sampling adapter designed to temporarily provide a means of sampling air from inside the face piece.


A quantitative fit-test determines a fit-factor for the employee based on the type

of the respirator used. A fit-factor is a quantitative estimate of the fit of a

particular respirator to a specific individual, and estimates the ratio:

Fit Factor = Concentration of particles in the ambient air Concentration of particles inside the

respirator when worn

To pass the fit-test, you need to obtain a fit-factor of at least 1,000.After the test, the fit-test report will indicate your overall fit-factor.

This sums up this training module, now you will need to take the Post Test!!

1120 Estes Drive Ext.1120 Estes Drive Ext.

Campus Box 1650Campus Box 1650

Chapel Hill, NC, 27599Chapel Hill, NC, 27599

Any questions regarding UNC-CH

Respiratory Protection Program,

please call:

Workplace Safety @ 962-5507

References

1) U.S. Department of Labor, Occupational Safety and Health Administration Guidelines for Coal Dust: http://www.osha.gov

2) National Institute for Occupational Safety and Health, NIOSH Pocket Guide to Chemical Hazards: http://www.cdc.gov/niosh/npg

3) Material Safety Data Sheet for Limestone, Martin Marietta Materials; 2710 Wycliff Road, Raleigh, NC 27607

4) Materials Safety Data Sheet for Coal Fly Ash, Pro-Ash;

Baltimore Gas and Electric STI Processed Ash, LLC.

http://www.osha.gov/

http://www.cdc.gov/niosh/npg

UNC Respiratory Protection Program for Energy Services CoGeneration Facility Mechanical Maintenance...

Documents

Transcript of UNC Respiratory Protection Program for Energy Services CoGeneration Facility Mechanical Maintenance...