UDDEHOLM VANADIS® 4 EXTRA

UDDEHOLM VANADIS® 4 EXTRASUPERCLEAN3

SS-EN ISO 9001SS-EN ISO 14001

This information is based on our present state of knowledge and is intended to provide generalnotes on our products and their uses. It should not therefore be construed as a warranty ofspecific properties of the products described or a warranty for fitness for a particular purpose.

Classified according to EU Directive 1999/45/ECFor further information see our “Material Safety Data Sheets”.

Edition 4, 09.2007

The latest revised edition of this brochure is the English version,which is always published on our web site www.uddeholm.com

3

UDDEHOLM VANADIS 4 EXTRA


CONSISTENT TOOL PERFORMANCE—LONG AND RELIABLE TOOL LIFE

With an increased demand for just in time deliveries (JIT) and shorter lead

time, it is of utmost importance that the tool life is predictable with a long and

reliable performance. This is also a prerequisite to reduce, your down time,

cost for tool maintenance and optimize machine utilization. This gives an

optimal tooling economy and a competitive production cost.

Uddeholm Vanadis 4 Extra properties offer very good combination of wear

resistance and ductility. This makes it possible for consistent tool performance

for demanding cold work applications such as blanking and forming of auste-

nitic stainless steels and advanced high strength steels (AHSS) where a

combination of abrasive, adhesive or mixed wear resistance is needed in

combination with resistance to chipping and cracking.

MACHINABILITY

The tool making process is a very important link in the tooling sequence. In

order to achieve a long and reliable tool performance the quality of the tool

in terms of surface finish is extremely important. Uddeholm Vanadis 4 Extra

offers a very good machinability and grindability compared to other high

alloyed PM- tool steels, giving the best conditions for an excellent tool quality.

This is the result of the well balanced chemistry and the SuperClean produc-

tion route.

4


Typical C Si Mn Cr Mo Vanalysis % 1,4 0,4 0,4 4,7 3,5 3,7

Deliverycondition Soft annealed to approx. 230 HB

Colour code Green/white with a black line across

ApplicationsUddeholm Vanadis 4 Extra is especially suitablefor applications where adhesive wear and/orchipping are the dominating failure mecha-nisms, i.e.• with soft/adherent materials such as auste-

nitic stainless steel, mild steel, copper, alumi-nium, etc.as work material

• with thicker work material

• high strength work materials

Uddeholm Vanadis 4 Extra is however alsovery suitable for blanking and forming of UltraHigh Strength Steel Sheet, these materialsplace high demands on the tool steel regardingabrasive wear resistance and ductility.

Examples:• Blanking and forming• Fine blanking• Cold extrusion tooling• Powder pressing• Deep drawing• Knives• Substrate steel for surface coating

Critical tool steelparametersFor good tool performance• Correct hardness for the application• High wear resistance• High ductility

High wear resistance is often associated withlow ductility and vice-versa. However, in manycases for optimal tool performance both highwear resistance and ductility are essential.

Uddeholm Vanadis 4 Extra is a powdermetallurgical cold work tool steel offering anextremely good combination of wear resistan-ce and ductility for high performance tools.

For toolmaking• Machinability• Heat treatment• Dimensional stability during heat treatment

Toolmaking with highly alloyed tool steels hastraditionally created problems with machiningand heat treatment when compared withlower alloyed grades, this then often leads toincreased toolmaking costs.

Due to our carefully balanced alloying andthe powder metallurgical manufacturing pro-cess, Uddeholm Vanadis 4 Extra has bettermachinability than the tool steel grade AISI D2.

One major advantage with UddeholmVanadis 4 Extra is that the dimensional stabilityafter hardening and tempering is much betterthan for all known high performance coldwork tool steels. This means, for example, thatUddeholm Vanadis 4 Extra is a tool steel whichis very suitable for CVD coating.

GeneralUddeholm Vanadis 4 Extra is a chromium-molybdenum-vanadium alloyed steel which ischaracterized by:• Very good ductility

• High abrasive-adhesive wear resistance

• High compressive strength

• Good dimensional stability during heattreatment and in service

• Very good through-hardening properties

• Good temper back resistance

• Good machinability and grindability

Hardened and tempered to 60 HRC.

Temperature 20°C 200°C 400°C(68°F) (390°F) (750°F)

Density, kg/m3 7 700 – – lbs/in3 0,278 – –

Modulus ofelasticity, N/mm2 206 000 200 000 185 000

psi 29,8 x 106 29,0 x 106 26,8 x 106

Coefficientof thermalexpansion per°C from 20°C – 10,9 x 10–6 11,7 x 10–6

°F from 68°F – 6,0 x 10–6 6,5 x 10–6

Thermalconductivity

W/m • °C _ 30 30Btu in/(ft2 h °F) _ 210 210

Specific heatJ/kg °C 460 – –Btu/lb °F 0,11 – –

PropertiesPhysical data

5


•

Retained austenite50

40

30

20

10

Heat treatmentSoft annealingProtect the steel and heat through to 900°C(1650°F). Cool in the furnace at 10°C (20°F)per hour to 750°C (1380°F), then freely in air.

Stress relievingAfter rough machining the tool should beheated through to 650°C (1200°F), holdingtime 2 hours. Cool slowly to 500°C (930°F),then freely in air.

HardeningPre-heating temperature: 600–700°C (1110–1290°F).

Austenitizing temperature: 940–1150°C (1725–2100°F). Normally 1020°C (1870°F). For largesections >70 mm (2,75") use 1060°C (1940°F).

Unnotched impact energy, J100 90 80 70 60 50 40 30 20 10

54 55 56 57 58 59 60 61 62 63 64 65 66 Hardness, HRC

Impact strengthApproximate room temperature impactstrength as a function of hardness is shownbelow.

Original bar dimension: Ø 105 mm, samples aretaken from the centre and tested in the trans-verse direction.

Specimen size: 7 x 10 x 55 mm (0,27 x 0,40 x2,2") unnotched.

Hardened between 940°C (1725°F) and1150°C (2100°F). Holding time 30 minutes upto 1100°C (2010°F), over 1100°C (2010°F)15 minutes. Quenched in air. Tempered 2 x 2hbetween 525°C (980°F) and 570°C (1060°F).

DIFFERENCE IN DUCTILITY

The difference in ductility between UddeholmVanadis 4 Extra and AISI D2 at differenthardness levels.

VANADIS 4 EXTRA

AISI D2

Retained austenite

Hardness

Hardness, HRC68

66

64

62

60

58

56

54

980 1000 1020 1040 1060 1080 1100 1120 1140°C

1795 1830 1870 1900 1940 1975 2010 2050 2085°F

Austenitizing temperature

Holding time: 30 min. up to 1100°C (2010°F),15 min. above 1100°C (2010°F).

Note: Holding time = time at hardeningtemperature after the tool is fully heatedthrough. A holding time of less than recom-mended above will result in loss of hardness.

Protect the part against decarburization andoxidation during hardening.

Quenching media• Vacuum (high speed gas at sufficient over-

pressure)

• Martempering bath or fluidized bed at500–550°C (930–1020°F)

• Martempering bath or fluidized bed at200–350°C (390–660°F)

Note 1: Temper the tool as soon as its tem-perature reaches 50–70°C (120–160°F).

Note 2: In order to obtain the optimum prop-erties for the tool, the cooling rate should beas fast as is concomitant with acceptabledistortion.

Note 3: Martempering should be followed byforced air cooling if wall thickness is exceeding70 mm (2,75").

HARDNESS AND RETAINED AUSTENITE AS AFUNCTION OF AUSTENITIZING TEMPERATURE

6


2000

1800

1600

1400

1200

1000

800

600

400

200

1100

1000

900

800

700

600

500

400

300

200

100

°C°F

CoolingCurveNo.

Hard-ness

HV 10

1 10 100 1 000 10 000 100 000 Seconds

Air cooling ofbars, Ø mm

inch

1 10 100 1 000 Minutes

1 10 100 Hours

0.20.008

1.50.06

10 0.39

90 3.5

600 23.6

1

53

139

415

700

2077

3500

7000

Austenitizing temp. 1020°C (1870°F)Holding time 30 min

1 2 3 4 5 6 7 8

Bainite

Carbides Pearlite

1

2

3

4

5

6

7

8

858

858

858

858

858

649

548

519

MartensiteMs

= 815°C (1500°F)Acs

= 880°C (1615°F)Ac f

sec800–500T

Hardness HRC

66

64

62

60

58

56

54

52

50

48

46

Retained austenite1100°C (2010°F)

Retained austenite %

35

30

25

20

15

10

5

Hardness HRC

66

64

62

60

58

56

54

52

50

48

46

400 450 500 550 600°C750 840 930 1020 1110°F

Tempering temperature (2h + 2h)

TEMPERING GRAPH

TemperingThe tempering temperature can be selectedaccording to the hardness required by refer-ence to the tempering graph below.

Temper twice with intermediate cooling toroom temperature. The lowest temperingtemperature which should be used is 525°C

(980°F). The minimum holding time at tem-perature is 2 hours.

In order not to reduce the toughness do nottemper below 525°C (980°F)

To avoid a high content of retained austenitechoose tempering temperature over 525°C(980°F).

Retained austenite1020°C (1870°F)

Retained austenite %

35

30

25

20

15

10

5

940°C (1725°F)

1100°C (2010°F)

1060°C (1940°F)

1150°C (2100°F)

1020°C (1870°F)

980°C (1795°F)

400 450 500 550 600°C750 840 930 1020 1110°F

Tempering temperature (2h + 2h)

CCT GRAPH

Austenitizing temperature 1020°C (1870°F). Holding time 30 minutes.

7


2000

1800

1600

1400

1200

1000

800

600

400

200

1 10 100 1 000 10 000 100 000 Seconds

1 10 100 1 000 Minutes

1 10 100 Hours

1100

1000

900

800

700

600

500

400

300

200

100

°C°F

Timehours

Hardn.HV 10

Temp.°C

Acf = 880°C (1615°F)

= 815°C (1500°F)

Austenitizing temp. 1020°C (1870°F)Holding time 30 min

Carbides

Bainite

Pearlite

Martensite

Acs

23,0

3.0

65,0

19,8

70,9

3,1

19,4

26,2

750

700

650

600

350

300

250

200

240

327

322

835

824

548

592

642

Sub-zero treatmentPieces requiring maximum dimensional stabilitycan be sub-zero treated as follows:Immediately after quenching the piece shouldbe sub-zero treated to between -70 and -80°C(-95 to -110°F), soaking time 3–4 hours,followed by tempering.

The tempering temperature should belowered 25°C (50°F) in order to get thedesired hardness when a high temperaturetemper is performed.

Avoid intricate shapes as there will be risk ofcracking.

Dimensional changes duringhardening and temperingDimensional changes have been measuredafter hardening and tempering.

Austenitizing: 1020°C/30 min. (1870°F/30 min.),cooling in vacuum furnace at 1,1°C/sec (2°F/sec) between 800°C (1470°F) and 500°C(930°F).

Tempering: 2 x 2 h at various temperatures

Sample size: 80 x 80 x 80 mm (3,15”x 3,15”x3,15”)

DIMENSIONAL CHANGES DURINGHARDENING AND TEMPERING IN LENGTH,WIDTH AND THICKNESS DIRECTION

Dimensional changes, % 0,12

0,10

0,08

0,06

0,04 0,02

0

-0,01

-0,04-0,06

500 510 520 530 540 550 560 570 °C930 950 970 990 1010 1030 1050 1070 °F

Tempering temperature

lengthwidththickness

TTT GRAPH

Austenitizing temperature 1020°C (1870°F). Holding time 30 minutes.

8


Relative machinability/grindability, (1=worse 5=best)5

4

3

2

1

Surface treatmentSome cold work tool steels are given a surfacetreatment in order to reduce friction andincrease wear resistance. The most commonlyused treatments are nitriding and surfacecoating with wear resistant layers produced viaPVD and CVD.

The high hardness and toughness togetherwith a good dimensional stability makesUddeholm Vanadis 4 Extra ideal as a substratesteel for various surface coatings.

NitridingNitriding gives a hard surface layer that isresistant to wear and erosion.

Uddeholm Vanadis 4 Extra is normally hightemperature tempered at around 525°C(980°F). This means that the nitriding tempera-ture used should not exceed 500–525°C (930–980°F). Ion nitriding at a temperature belowthe tempering temperature used is preferred.The surface hardness after nitriding is approxi-mately 1150 HV0,2 kg.

The thickness of the layer should be chosento suit the application in question.

PVDPhysical vapour deposition, PVD, is a methodof applying a wear resistant coating at tem-peratures between 200–500°C (390–930°F).

CVDChemical vapour deposition, CVD, is used forapplying wear resistant surface coatings at atemperature of around 1000°C (1830°F). It isrecommended that the tools should beseparately hardened and tempered in a vacuumfurnace after surface treatment.

AISI D2 PM 23 VANADIS 4 EXTRA

MachiningrecommendationsThe cutting data below are to be consideredas guiding values which must be adapted toexisting local conditions.

The recommendations, in following tables, arevalid for Uddeholm Vanadis 4 Extra in softannealed condition to ~230 HB.

Turning

Turning with carbide TurningCutting data Rough Fine with HSSparameters turning turning Fine turning

Cutting speed (vc)m/min. 120–170 170–220 15–20f.p.m. 395–560 560–720 50–65

Feed (f)mm/rev. 0,2–0,4 0,05–0,2 0,05–0,3i.p.r. 0,008–0,016 0,002–0,008 0,002–0,012

Depth of cut (ap)mm 2–4 0,5–2 0,5–3inch 0,08–0,16 0,02–0,08 0,02–0,08

Carbide designationISO K20*, P20* K15*, P15* –

* Use a wear resistant CVD-coated carbide grade

MachinabilityRelative machinability and grindability forAISI D2, PM 23 and Uddeholm Vanadis 4 Extra.High value indicates good machinability/grindability.

9


Drill diameter Cutting speed (vc) Feed (f)mm inch m/min f.p.m. mm/rev i.p.r.

–5 –3/16 12–14* 40–46* 0,05–0,15 0,002–0,006 5–10 3/16–3/8 12–14* 40–46* 0,15–0,25 0,006–0,01010–15 3/8 –5/8 12–14* 40–46* 0,25–0,30 0,010–0,01215–20 5/8 –3/4 12–14* 40–46* 0,30–0,35 0,012–0,014

* For coated HSS drills vc = 22–24 m/min. (72–80 f.p.m.)

DrillingHIGH SPEED STEEL TWIST DRILL

1) Drills with internal cooling channels and a brazed tip2) Depending on drill diameter

CARBIDE DRILL

Type of drill

Cutting data Indexable Solid Brazedparameters insert carbide carbide1)

Cuttingspeed (vc)

m/min. 140–160 80–100 50–60f.p.m. 460–525 260–330 165–200

Feed (f)mm/rev. 0,05–0,152) 0,10–0,252) 0,15–0,252)

i.p.r. 0,002–0,0062) 0,004–0,0102) 0,006–0,012)

GrindingA general grinding wheel recommendation isgiven below. More information can be found inthe Uddeholm publication “Grinding of ToolSteel”.

WHEEL RECOMMENDATION

Soft annealed HardenedType of grinding condition condition

Face grinding A 46 HV B151 R50 B31)

straight wheel A 46 HV2)

Face grinding A 24 GV A46 FV2)

segments

Cylindrical grinding A 60 KV B151 R75 B31)

A 60 KV2)

Internal grinding A 60 JV B151 R75 B31)

A 60 KV2)

Profile grinding A 100 LV B126 R100 B61)

A 80 JV2)

1) If possible use CBN wheels for this application2) Grinding wheels containing ceramic Al2O3 type is recommended

Electrical-dischargemachining—EDMIf EDM is performed in the hardened andtempered condition, finish with “fine-sparking”,i.e. low current, high frequency. For optimalperformance the EDM’d surface should thenbe ground/polished and the tool retemperedat approx. 25°C (45°F) lower than the originaltempering temperature.

When EDM’ing larger sizes or complicatedshapes Uddeholm Vanadis 4 Extra should betempered at high temperatures, above 500°C(930°F).

END MILLING

Type of milling

Cutting data Solid Carbide index- High speedparameters carbide able insert steel1)

Cuttingspeed (vc)

m/min. 60–80 110–160 8–12f.p.m. 200–260 360–525 26–40

Feed (fz)mm/tooth 0,03–0,202) 0,08–0,202) 0,05–0,352)

in/tooth 0,001–0,0082) 0,003–0,0082) 0,002–0,0142)

Carbidedesignation

ISO – K153) –

1) For coated HSS end mill vc = 18–24 m/min. (60–80 f.p.m.)2) Depending on radial depth of cut and cutter diameter3) Use a wear resistant CVD coated carbide grade

MillingFACE AND SQUARE SHOULDER MILLING

Milling with carbide

Cutting data parameters Rough milling Fine milling

Cutting speed (vc)m/min. 110–150 150–200f.p.m. 360–490 490–655

Feed (fz)mm/tooth 0,2–0,4 0,1–0,2in/tooth 0,008–0,016 0,004–0,008

Depth of cut (ap)mm 2–4 – 2inch 0,08–0,16 – 0,08

Carbide designation ISO K20, P20 K15, P15coated carbide* coated carbide*

* Use a wear resistant CVD coated carbide grade

10


ARNE

CALMAX

CALDIE (ESR)

RIGOR

SLEIPNER

SVERKER 21

SVERKER 3

VANADIS 4 Extra

VANADIS 6

VANADIS 10

VANCRON 40

VANADIS 23

VANADIS 30

VANADIS 60

AISI M2

Powder metallurgical high speed steel

Powder metallurgical tool steel

Conventional cold work tool steel

Conventional high speed steel

Relative comparison ofUddeholm cold work tool steelMaterial properties and resistance to failure mechanisms

Hardness/ Fatigue cracking resistanceResistance Resistance to Ductility/ Toughness/

Uddeholm to plastic Machin- Grind- Dimension Abrasive Adhesive resistance to gross grade deformation ability ability stability wear wear/Galling chipping cracking

Further informationPlease contact your local Uddeholm office forfurther information on the selection, heattreatment, application and availability of Udde-holm tool steels.

11


The Powder Metallurgy processIn the powder metallurgy process nitrogen gas is used toatomise the melted steel into small droplets, or grains.Each of these small grains solidifies quickly and there islittle time for carbides to grow. These powder grains arethen compacted to an ingot in a hot isostatic press (HIP)at high temperature and pressure. The ingot is then rolledor forged to steel bars by conventional methods.

The resulting structure is completely homogeneoussteel with randomly distributed small carbides, harmlessas sites for crack initiation but still protecting the toolfrom wear.

Large slag inclusions can take the role as sites for crackinitiation instead. Therefore, the powder metallurgicalprocess has been further developed in stages to improvethe cleanliness of the steel. Powder steel from UddeholmTooling is today of the third generation. It is marketedunder the brand SUPERCLEAN3 and is considered thecleanest powder metallurgy tool steel product on themarket.

HEAT TREATMENT

Prior to delivery all of the different bar materials aresubjected to a heat treatment operation, either as softannealing or hardening and tempering. These operationsprovide the steel with the right balance between hardnessand toughness.

MACHINING

Before the material is finished and put into stock, we alsorough machine the bar profiles to required size and exacttolerances. In the lathe machining of large dimensions, thesteel bar rotates against a stationary cutting tool. In peel-ing of smaller dimensions, the cutting tools revolve aroundthe bar.

To safeguard our quality and guarantee the integrity ofthe tool steel we perform both surface- and ultrasonicinspections on all bars. We then remove the bar ends andany defects found during the inspection.

ROLLING MILL

FORGING

STOCK

POWDER METALLURGYPROCESS

MACHINING

HEATTREATMENT

12


EuropeAustriaRepresentative officeUDDEHOLMAlbstraße 10DE-73765 NeuhausenTelephone: +49 7158 9865-0www.uddeholm.de

BelgiumUDDEHOLMEuropark Oost 7B-9100 Sint-NiklaasTelephone: +32 3 780 56 20www.uddeholm.be

CroatiaBÖHLER UDDEHOLM Zagrebd.o.o za trgovinuZitnjak b.b10000 ZagrebTelephone: +385 1 2459 301Telefax: +385 1 2406 790www.bohler-uddeholm.hr

Czech RepublicBÖHLER UDDEHOLM CZ s.r.o.Division UddeholmU Silnice 949161 00 Praha 6, RuzyneTelephone: +420 233 029 850,8www.uddeholm.cz

DenmarkUDDEHOLM A/SKokmose 8, BramdrupdamDK-6000 KoldingTelephone: +45 75 51 70 66www.uddeholm.dk

EstoniaUDDEHOLM TOOLING ABSilikatsiidi 7EE-11216 TallinnTelephone: +372 655 9180www.uddeholm.ee

FinlandOY UDDEHOLM ABRitakuja 1, PL 57FI-01741 VANTAATelephone: +358 9 290 490www.uddeholm.fi

FranceHead officeUDDEHOLMZ.I. de Mitry-Compans, 12 rue Mercier,FR-77297 Mitry Mory CedexTelephone: +33 (0)1 60 93 80 10www.uddeholm.fr

Branch officesUDDEHOLM S.A.77bis, rue de VesoulLa Nef aux MétiersFR-25000 BesançonTelephone: +33 (0)381 53 12 19

LE POINT ACIERSUDDEHOLM - Aciers à outilsZ.I. du Recou, Avenue de ChamplevertFR-69520 GRIGNYTelephone: +33 (0)4 72 49 95 61

LE POINT ACIERSUDDEHOLM - Aciers à outilsZ.I. Nord 27, rue François RochaixFR-01100 OYONNAXTelephone: +33 (0)4 74 73 48 66

GermanyHead officeUDDEHOLMHansaallee 321DE-40549 DüsseldorfTelephone: +49 211 5351-0www.uddeholm.de

Branch officesUDDEHOLMFalkenstraße 21DE-65812 Bad Soden/TSTelephone: +49 6196 6596-0

UDDEHOLMAlbstraße 10DE-73765 NeuhausenTelephone: +49 7158 9865-0

UDDEHOLMFriederikenstraße 14bDE-06493 HarzgerodeTelephone: +49 39484 727 267

Great BritainUDDEHOLM DIVISIONBOHLER-UDDEHOLM (UK) LIMITEDEuropean Business ParkTaylors Lane, OldburyGB-West Midlands B69 2BNTelephone: +44 121 552 5511Telefax: +44 121 544 2911www.uddeholm.co.uk

GreeceSTASSINOPOULOS-UDDEHOLMSTEEL TRADING S.A.20, Athinon StreetGR-Piraeus 18540Telephone: +30 210 4172 109www.uddeholm.gr

SKLERO S.A.Heat Treatment and Trading of SteelUddeholm Tool SteelsIndustrial Area of ThessalonikiP.O. Box 1123GR-57022 Sindos, ThessalonikiTelephone: +30 2310 79 76 46www.sklero.gr

HungaryUDDEHOLM TOOLING/BOKDunaharaszti, Jedlik Ányos út 25HU-2331 Dunaharaszti 1. Pf. 110Telephone/fax:+36 24 492 690www.uddeholm.hu

IrelandHead office:UDDEHOLM DIVISIONBOHLER-UDDEHOLM (UK) LIMITEDEuropean Business ParkTaylors Lane, OldburyUK-West Midlands B69 2BNTelephone: +44 121 552 5511Telefax: +44 121 544 2911www.uddeholm.co.ukDublin:Telephone: +353 1845 1401

ItalyUDDEHOLMDivisione della Bohler UddeholmItalia S.p.A.Via Palizzi, 90IT-20157 MilanoTelephone: +39 02 39 49 211www.uddeholm.it

LatviaUDDEHOLM TOOLING LATVIA SIAPiedrujas Street 7LV-1035 RigaTelephone: +371 7 702133Telefax: +371 7 185079

Branch officeUDDEHOLMBarrio San Martín de Arteaga,132Pol.Ind. TorrelarragoitiES-48170 Zamudio (Bizkaia)Telephone: +34 94 452 13 03

SwedenHead officeUDDEHOLM TOOLING SVENSKA ABAminogatan 25SE-431 53 MölndalTelephone: +46 31 67 98 50www.uddeholm.se

Branch officesUDDEHOLM TOOLING SVENSKA ABBox 45SE-334 21 AnderstorpTelephone: +46 371 160 15

UDDEHOLM TOOLING SVENSKA ABBox 148SE-631 03 EskilstunaTelephone: +46 16 15 79 00

UDDEHOLM TOOLING SVENSKA ABAminogatan 25SE-431 53 MölndalTelephone: +46 31 67 98 70

UDDEHOLM TOOLING SVENSKA ABNya Tanneforsvägen 96SE-582 42 LinköpingTelephone: +46 13 15 19 90

UDDEHOLM TOOLING SVENSKA ABDerbyvägen 22SE-212 35 MalmöTelephone: +46 40 22 32 05

UDDEHOLM TOOLING SVENSKA ABHonnörsgatan 16ASE-352 36 VäxjöTelephone: +46 470 457 90

SwitzerlandHERTSCH & CIE AGGeneral Wille Strasse 19CH-8027 ZürichTelephone: +41 44 208 16 66www.hertsch.ch

TurkeyHead officeASSAB Korkmaz Celik A.S.Organize Sanayi Bölgesi2. Cadde No: 26 Y. Dudullu34776 UmraniyeIstanbul TurkeyTelephone: +90 216 420 1926-121/124www.assabkorkmaz.com

LithuaniaUDDEHOLM TOOLING ABBE PLIENAS IR METALAIT. Masiulio 18BLT-52459 KaunasTelephone: +370 37 370613, -669www.besteel.lt

The NetherlandsUDDEHOLMIsolatorweg 30NL-1014 AS AmsterdamTelephone: +31 20 581 71 11www.uddeholm.nl

NorwayUDDEHOLM A/SJernkroken 18Postboks 85, KalbakkenNO-0902 OsloTelephone: +47 22 91 80 00www.uddeholm.no

PolandBOHLER UDDEHOLM POLSKASp. z.o.o./Co. Ltd.ul. Kolejowa 291, Dziekanów Polski,PL-05-092 LomiankiTelephone: +48 22 429 2260, -203, -204www.uddeholm.pl

PortugalF RAMADA Aços e Industrias S.A.P.O. Box 10PT-3881 Ovar CodexTelephone: +351 256 580580www.ramada.pt

RomaniaBÖHLER-UDDEHOLM Romania SRLAtomistilor Str. No 96-102077125 - com. Magurele, Jud. Ilfov.Telephone: +40 214 575007Telefax: +40 214 574212

RussiaUDDEHOLM TOOLING CIS9A, Lipovaya Alleya, Office 509RU-197183 Saint PetersburgTelephone: +7 812 6006194www.uddeholm.ru

SlovakiaBohler-Uddeholm Slovakia s.r.o.divizia UDDEHOLMCsl.Armády 5622/5SK-036 01 MartinTelephone: +421 (0)434 212 030www.uddeholm.sk

SloveniaRepresentative officeUDDEHOLMDivisione della Bohler UddeholmItalia S.p.A.Via Palizzi, 90IT-20157 MilanoTelephone: +39 02 39 49 211www.uddeholm.it

SpainHead officeUDDEHOLMGuifré 690-692ES-08918 Badalona, BarcelonaTelephone: +34 93 460 1227www.acerosuddeholm.com

ˇ

13


AmericaArgentinaACEROS BOEHLER UDDEHOLM S.AMozart 401619-Centro Industrial GarinGarin-Prov.AR-Buenos AiresTelephone: +54 332 7444 440www.uddeholm.com.ar

BrazilAÇOS BOHLER-UDDEHOLM DOBRASIL LTDA– DIV. UDDEHOLMEstrada Yae Massumoto, 353CEP 09842-160BR-Sao Bernardo do Campo - SP BrazilTelephone: +55 11 4393 4560, 4554www.uddeholm.com.br

CanadaHead Office & WarehouseUDDEHOLM2595 Meadowvale Blvd.Mississauga, ON L5N 7Y3Telephone: +1 905 812 9440www.bucanada.com

Branch WarehousesUDDEHOLM3521 Rue AshbySt. Laurent, QC H4R 2K3Telephone: +1 514 333 8000

UDDEHOLM730 Eaton Way - Unit #10New Westminister, BC V3M 6J9Telephone: +1 604 525 3354

Heat TreatingTHERMO-TECH2645 Meadowvale Blvd.Mississauga, ON L5N 7Y4Telephone: +1 905 812 9440

ColombiaAXXECOL S.A.Carrera 35 No 13-20Apartado Aereo 80718CO-Bogota 6Telephone: +57 1 2010700www.axxecol.com

ASTECO S.A.Carrera 54 No 35-12Apartado Aereo 663CO-MedellinTelephone: +57 4 2320122www.asteco.com

Dominican RepublicRAMCA, C. POR A.P-2289P.O. Box 025650Miami, Fl. 33102Telephone: +1 809 682 [email protected]

EcuadorIVAN BOHMAN C.A.Apartado 1317Km 6 1/2 Via a DauleGuayaquilTelephone: +593 42 254111

IVAN BOHMAN C.A.Casilla Postal 17-01370QuitoTelephone: +593 2 2248001

El SalvadorACAVISA DE C.V.25a. Avenida Sur 463zona 1Apartado Postal 439SV-San SalvadorTelephone: +503 22 711700www.acavisa.com

GuatemalaIMPORTADORA ESCANDINAVAApartado postal 11CGT-Guatemala City, GuatemalaTelephone: +502 23 [email protected]

MexicoHead officeACEROS BOHLER UDDEHOLM S.A.de C.V.Calle Ocho No 2, Letra ”C”Fraccionamiento Industrial Alce BlancoC.P. 52787 Naucalpan de JuarezMX-Estado de MexicoTelephone: +52 55 9172 0242www.bu-mexico.com

Branch officeBOHLER-UDDEHOLM MONTERREY,NUEVO LEONLerdo de Tejada No.542Colonia Las VillasMX-66420 San Nicolas de Los Garza,N.L.Telephone: +52 81 83 525239

PeruC.I.P.E.S.AAv. Oscar R. Benavides(ante Colonial) No. 2066PE-Lima 1Telephone: +51 1 336 [email protected]

U.S.A.Head OfficeUDDEHOLM4902 Tollview DriveRolling Meadows IL 60008Telephone: 1-847-577-2220Sales phone: 1-800-638-2520www.bucorp.com

Region East WarehouseUDDEHOLM220 Cherry StreetShrewsbury MA 01545

Region Central WarehouseUDDEHOLM548 Clayton Ct.Wood Dale IL 60191

Region West WarehouseUDDEHOLM9331 Santa Fe Springs RoadSanta Fe Springs, CA 90670

VenezuelaPRODUCTOS HUMAR C.A.Multicentro Empresarial del Este,Edf Libertador, Núcleo A.Piso 9, Of. A-93, ChacaoVE-Caracas 1060Telephone: +58 212 [email protected]

Other Countries in AmericaASSAB INTERNATIONAL ABBox 42SE-171 11 Solna, SwedenTelephone: +46 8 564 616 70www.assab.se

Asia & PacificAustraliaBOHLER UDDEHOLM Australia129-135 McCredie RoadGuildford NSW 2161Private Bag 14AU-SydneyTelephone: +61 2 9681 3100www.buau.com.au

BangladeshASSAB INTERNATIONAL ABP.O. Box 17595Jebel AliAE-DubaiTelephone: +971 488 12165www.assab.se

North ChinaHead officeASSAB Tooling (Beijing) Co LtdNo.10A Rong Jing Dong JieBeijing Economic Development AreaBeijing 100176, ChinaTelephone: +86 10 6786 5588www.assabsteels.com

Branch officesASSAB Tooling (Beijing) LtdDalian Branch8 Huanghai Street, Haerbin RoadEconomic & Technical Develop. DistrictDalian 116600, ChinaTelephone: +86 411 8761 8080

ASSAB Qingdao OfficeRoom 2521, Kexin MansionNo. 228 Liaoning Road, Shibei DistrictQingdao 266012, ChinaTelephone: +86 532 8382 0930

ASSAB Tianjin OfficeNo.12 Puwangli Wanda XinchengXinyibai Road, Beichen DistrictTianjin 300402, ChinaTelephone: +86 22 2672 0006

Central ChinaHead officeASSAB Tooling Technology(Shanghai) Co LtdNo. 4088 Humin RoadXinzhuang Industrial ZoneShanghai 201108, ChinaTelephone: +86 21 5442 2345www.assabsteels.com

Branch officesASSAB Tooling Technology(Ningbo) Co LtdNo. 218 Longjiaoshan RoadVehicle Part Industrial ParkNingbo Economic & Technical Dev.ZoneNingbo 315806, ChinaTelephone: +86 574 8680 7188

ASSAB Tooling Technology(Chongqing) Co LtdPlant C, Automotive Industrial lParkChongqing Economic & TechnologicalDevelopment ZoneChongqing 401120, ChinaTelephone: +86 23 6745 5698

South ChinaHead officeASSAB Steels (HK) LtdRoom 1701–1706Tower 2 Grand Central Plaza138 Shatin Rural Committee RoadShatin NT - Hong KongTelephone: +852 2487 1991www.assabsteels.com

Branch officesASSAB Tooling (Dongguan) Co LtdNorthern DistrictSong Shan Lake Science & TechnologyIndustrial ParkDongguan 523808, ChinaTelephone: +86 769 2289 7888www.assabsteels.com

ASSAB Tooling (Xiamen) Co LtdFirst Floor Universal WorkshopNo. 30 Huli ZoneXiamen 361006, ChinaTelephone: +86 592 562 4678

Hong KongASSAB Steels (HK) LtdRoom 1701-1706Grand Central Plaza, Tower 2138 Shatin Rural Committee RoadShatin NT, Hong KongTelephone: +852 2487 1991www.assabsteels.com

IndiaASSAB Sripad Steels LTDT 303 D.A.V. ComplexMayur Vihar Ph I ExtensionIN-Delhi-110 091Telephone: +91 11 2271 2736www.assabsripadsteels.com

ASSAB Sripad Steels LTD709, Swastik ChambersSion-Trombay RoadChemburIN-Mumbai-400 071Telephone: +91 22 2522-7110, -8133

ASSAB Sripad Steels LTDPadmalaya TowersJanaki AvenueM.R.C. NagarIN-Chennai-600 028Telephone: +91 44 2495 2371

ASSAB Sripad Steels LTD19X, D. P. P. RoadNaktola Post OfficeIN-Kolkata-700 047Telephone: +91 (33) 400 1645

ASSAB Sripad Steels LTDGround floor, Plot No 11-6-8Opp IDPL Factory Out GateBalanagarIN-Hyderabad-500 037Telephone: +91 (40) 2377 8148

IndonesiaHead officePT ASSAB Steels IndonesiaJl. Rawagelam III No. 5Kawasan Industri PulogadungJakarta 13930, IndonesiaTelephone: +62 21 461 1314www.assabsteels.com

Branch officesSURABAYA BRANCHJl. Berbek Industri 1/23Surabaya Industrial Estate, RungkutSurabaya 60293, East Java, IndonesiaTelephone: +62 31 843 2277

MEDAN BRANCHKomplek Griya Riatur IndahBlok A No.138Jl. T. Amir HamzahHalvetia Timur, Medan 20124Telephone: +62 61 847 7935/6

BANDUNG BRANCHKomp. Ruko Bumi KencanaJl. Titian Kencana Blok ENo.5 Bandung 40233Telephone: +62 22 604 1364

14


TANGERANG BRANCHPusat Niaga CibodasBlok C No. 7 TangerangTelephone: +62 21 921 9596, 551 2732

SEMARANG BRANCHJl. Imam Bonjol No.155R.208 Semarang 50124Telephone: +62 358 8167

IranASSAB INTERNATIONAL ABP.O. Box 19395IR-1517 TEHRANTelephone: +98 21 888 35392www.assabiran.com

IsraelPACKER YADPAZ QUALITYSTEELS LtdP.O. Box 686Ha-Yarkon St. 7, Industrial ZoneIL-81106 YAVNETelephone: +972 8 932 8182www.packer.co.il

JapanUDDEHOLM KKAtago East Building3-16-11 Nishi ShinbashiMinato-ku, Tokyo 105-0003, JapanTelephone: + 81 3 5473 4641www.assabsteels.com

JordanENGINEERING WAY Est.P.O. Box 874Abu AlandaJO-AMMAN 11592Telephone: +962 6 [email protected]

MalaysiaHead officeASSAB Steels (Malaysia) Sdn BhdLot 19, Jalan Perusahaan 2Batu Caves Industrial Estate68100 Batu CavesSelangor MalaysiaTelephone: +60 3 6189 0022www.assabsteels.com

Branch officesBUTTERWORTH BRANCHPlot 146aJalan Perindustrial Bukit Minyak 7Kawasan Perindustrial Bukit Minyak14000 Bukit Mertajam, SPT PenangTelephone: +60 4 507 2020

JOHOR BRANCHNo. 8, Jalan Persiaran TeknologiTaman Teknologi81400 SenaiJohor DT, MalaysiaTelephone: +60 7 598 0011

New ZealandVIKING STEELS25 Beach Road, OtahuhuP.O. Box 13-359, OnehungaNZ-AucklandTelephone: +64 9 270 1199www.ssm.co.nz

PakistanASSAB International ABP.O. Box 17595Jebel AliAE-DubaiTelephone: +971 488 12165www.assab.se

PhilippinesASSOCIATED SWEDISH STEELSPHILS Inc.No. 3 E. Rodriguez Jr., AvenueBagong Ilog, Pasig CityPhilippinesTelephone: +632 671 1953/2048www.assabsteels.com

Republic of KoreaHead officeASSAB Steels (Korea) Co Ltd116B-8L, 687-8, Kojan-dongNamdong-kuIncheon 405-310, KoreaTelephone: +82 32 821 4300www.assabsteels.com

Branch officesBUSAN BRANCH14B-5L, 1483-9, Songjeong-dongKangseo-ku, Busan 618-270, KoreaTelephone: +82 51 831 3315

DAEGU BRANCHRoom 27, 7-Dong2 FIndustry Materials Bldg.1629Sangyeog-Dong, Buk-KuKorea-Daegu 702-710Telephone: +82 53 604 5133

LebanonWARDE STEEL & METALS SARL METCharles Helou Av, Warde BldgP.O. Box 165886LB-BeirutTelephone: +961 1 [email protected]

Saudi ArabiaASSAB INTERNATIONAL ABP.O. Box 255092SA-Riyadh 11353Telephone: +966 1 [email protected]

SingaporeHead office PacificASSAB Pacific Pte Ltd171, Chin Swee RoadNo. 07-02, SAN CentreSG-Singapore 169877Telephone: +65 6534 5600www.assabsteels.com

JurongASSAB Steels Singapore (Pte) Ltd18, Penjuru CloseSG-608616 SingaporeTelephone: +65 6862 2200

Sri LankaGERMANIA COLOMBO PRIVATE Ltd.451/A Kandy RoadLK-KelaniyaTelephone: +94 11 2913556www.iwsholdings.com

SyriaWARDE STEEL & METALS SARL METCharles Helou Av, Warde BldgP.O. Box 165886LB-BeirutTelephone: +961 1 [email protected]

TaiwanHead officeASSAB Steels (Taiwan) Co LtdNo. 112 Wu Kung 1st Rd.Wu Ku Industry ZoneTW-Taipei 248-87, Taiwan (R.O.C.)Telephone: +886 2 2299 2849www.assabsteels.com

Branch officesNANTOU BRANCHNo. 10, Industry South 5th RoadNan Kang Industry ZoneNantou 540-66, Taiwan (R.O.C.)Telephone: +886 49 225 1702TAINAN BRANCHNo. 180, Yen He Street,Yong Kang CityTainan 710-82, Taiwan (R.O.C.)Telephone: +886 6 242 6838

ThailandASSAB Steels (Thailand) Ltd9/8 Soi Theedinthai,Taeparak Road, Bangplee,Samutprakarn 10540, ThailandTelephone: +66 2 385 5937,+66 2 757 5017www.assabsteels.com

United Arab EmiratesASSAB INTERNATIONAL ABP.O. Box 17595Jebel AliAE-DubaiTelephone: +971 488 12165www.assab.se

VietnamCAM Trading Steel Co Ltd90/8 Block 5, Tan Thoi Nhat WardDistrict 12, Ho Chi Minh CityVietnamTelephone: +84 8 5920 920www.assabsteels.com

Other AsiaASSAB INTERNATIONAL ABBox 42E-171 11 Solna, SwedenTelephone: +46 8 564 616 70www.assab.se

AfricaEgyptUNITED FOR IMPORT ANDINDUSTRIAL SUPPLIESMontaser Project No 20Flat No 14Al Ahram Street-El TabiaEG-Giza CairoTelephone: +20 2 7797751www.assab.se

KenyaSANDVIK Kenya LtdP.O. Box 18264Post code 00500KE-NairobiTelephone: +254 20 532 [email protected]

South AfricaUDDEHOLM Africa (Pty.) Ltd.P.O. Box 539ZA-1600 Isando/JohannesburgTelephone: +27 (11) 974 2791www.bohler-uddeholm.co.za

TunisiaMCM Distribution4 Bis, Rue 8610 - Z.I.2035 Chargula 1TN-TunisTelephone: + 216 71 802479www.mcm.com.tn

ZimbabweRepresentative office:UDDEHOLM Africa (Pty.) Ltd.P.O. Box 539ZA-1600 Isando/JohannesburgTelephone: +27 11 974 2781www.bohler-uddeholm.co.za

Other African CountriesASSAB INTERNATIONAL ABBox 42SE-171 11 Solna, SwedenTelephone: +46 8 564 616 70www.assab.se

www.assab.com www.uddeholm.com www.uddeholm.com

Network of excellenceUddeholm is present on every continent. This ensures you

high-quality Swedish tool steel and local support wherever you

are. Assab is our wholly-owned subsidiary and exclusive sales

channel, representing Uddeholm in various parts of the world.

Together we secure our position as the world’s leading supplier

of tooling materials.

HA

GFO

RS KLARTEX

T U070902.1000 / TRY

CKERI KN

APPEN

, KARLSTA

D 200709033

Uddeholm is the world’s leading supplier of tooling materials. This

is a position we have reached by improving our customers’ everyday

business. Long tradition combined with research and product develop-

ment equips Uddeholm to solve any tooling problem that may arise.

It is a challenging process, but the goal is clear – to be your number one

partner and tool steel provider.

Our presence on every continent guarantees you the same high quality

wherever you are. Assab is our wholly-owned subsidiary and exclusive

sales channel, representing Uddeholm in various parts of the world.

Together we secure our position as the world’s leading supplier of

tooling materials. We act worldwide, so there is always an Uddeholm

or Assab representative close at hand to give local advice and support.

For us it is all a matter of trust – in long-term partnerships as well as in

developing new products. Trust is something you earn, every day.

For more information, please visit www.uddeholm.com or www.assab.com

UDDEHOLM VANADIS® 4 EXTRA

Documents

Transcript of UDDEHOLM VANADIS® 4 EXTRA