TYPICAL DRAWING / ARTIS PHENO - Siemens Healthineers Pheno//16055.pdf · artis pheno 16055a-101...

ARTIS PHENO

16055

A-101ATTENTION:

RE

FE

RE

NC

E D

OC

UM

EN

T - N

OT

F

OR

C

ON

ST

RU

CT

IO

N

ATTENTION:

RE

FE

RE

NC

E D

OC

UM

EN

T - N

OT

F

OR

C

ON

ST

RU

CT

IO

N

AutoCAD SHX Text

ARTIS PHENO

AutoCAD SHX Text

REV. 9

AutoCAD SHX Text

DESIGNATION

AutoCAD SHX Text

PG NUMBER

AutoCAD SHX Text

DATE

AutoCAD SHX Text

RESOURCE LIST (SMS USE ONLY)

AutoCAD SHX Text

ARTIS PHENO

AutoCAD SHX Text

AXHE-040.891.01.01.02

AutoCAD SHX Text

04.17

AutoCAD SHX Text

TYPICAL DRAWING / ARTIS PHENO

AutoCAD SHX Text

AS NOTED

AutoCAD SHX Text

THE USE OR REPRODUCTION OF

AutoCAD SHX Text

THIS TITLE BLOCK WITHOUT

AutoCAD SHX Text

PROJECT #:

AutoCAD SHX Text

SHEET:

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text

REF. #:

AutoCAD SHX Text

FULL EXTENT OF THE LAW.

AutoCAD SHX Text

SIEMENS AUTHORIZATION WILL

AutoCAD SHX Text

RESULT IN PROSECUTION UNDER

AutoCAD SHX Text

SHEET OF

AutoCAD SHX Text

DATE:

AutoCAD SHX Text

SHEET OF

AutoCAD SHX Text

DRAWN BY:

AutoCAD SHX Text

DRAWN BY:

AutoCAD SHX Text

SUGGESTED 2'-6" SQUARE SHELF 48" A.F.F. FOR MOUNTING FD COOLER ABOVE TUBE COOLER.

AutoCAD SHX Text

NOTE: THE UPS IS SUPPLIED AND DELIVERED TO CUSTOMER'S LOADING DOCK BY SIEMENS. CUSTOMER'S ELECTRICIAN IS RESPONSIBLE FOR MOVING FROM LOADING DOCK TO FINAL LOCATION AND COMPLETING ALL CONNECTIONS. THE UPS MUST NOT BE LOCATED IN A PATIENT ENVIRONMENT. SIEMENS PROJECT MANAGER WILL SCHEDULE UPS STARTUP PRIOR TO DELIVERY OF SIEMENS IMAGING EQUIPMENT.

AutoCAD SHX Text

IN CASE OF POWER FAILURE, A UPS PROVIDING TABLE MOVEMENT IS REQUIRED WHEN A TILTING/OR TABLE IS PURCHASED. IF NOT PURCHASED FROM SIEMENS, IT IS THE CUSTOMER'S RESPONSIBILITY TO PROVIDE A UPS THAT ALLOWS A TILTING/OR TABLE TO BE MOVED TO A ZERO DEGREE POSITION DESIGNATED FOR CPR WITHIN 15 SECONDS. THIS REQUIREMENT IS CONSISTENT WITH IEC 60601-2-43 CL. 201.15.101. IF THE CUSTOMER OR SIEMENS-SUPPLIED UPS SOLUTION IS NOT INSTALLED AND OPERATIONAL AT THE TIME OF THE SIEMENS DELIVERY, SIEMENS CANNOT AND WILL NOT INSTALL THE AFFECTED SIEMENS SYSTEM!

AutoCAD SHX Text

M-501

AutoCAD SHX Text

1

AutoCAD SHX Text

M-501

AutoCAD SHX Text

2

AutoCAD SHX Text

AREA B: NON-SYSTEM CEILING COMPONENTS THAT : NON-SYSTEM CEILING COMPONENTS THAT ARE MOUNTED IN THIS AREA MUST MEET THE FOLLOWING REQUIREMENTS: * THE BOTTOM EDGE OF ANY FIXED COMPONENT MUST BE NO LESS THAN 8'-6 3/8" A.F.F. * ANY COMPONENT EXTENDING BELOW 8'-6 3/8" A.F.F. MUST HAVE THE ABILITY TO MOVE OUTSIDE THE AREA SHOWN VIA ARTICULATION, TRACK MOUNTING, ETC.

AutoCAD SHX Text

PATIENT TABLE MOVEMENT RANGE (HEAD-END)

AutoCAD SHX Text

SINKS, COUNTERTOPS AND ALL CASEWORK SHOWN IS SUGGESTED AND MUST BE DESIGNED SUPPLIED AND INSTALLED BY CUSTOMER/ CONTRACTOR.

AutoCAD SHX Text

SPACE FOR CUSTOMER EQUIPMENT

AutoCAD SHX Text

PROPOSED 2'-6" DEEP COUNTERTOP, MIN. 30" A.F.F PROVIDED BY CUSTOMER/CONTRACTOR.

AutoCAD SHX Text

1

AutoCAD SHX Text

2

AutoCAD SHX Text

3

AutoCAD SHX Text

4

AutoCAD SHX Text

CONTROL ROOM

AutoCAD SHX Text

PROCEDURE ROOM

AutoCAD SHX Text

EQUIP. ROOM

AutoCAD SHX Text

14

AutoCAD SHX Text

13

AutoCAD SHX Text

12

AutoCAD SHX Text

11

AutoCAD SHX Text

10

AutoCAD SHX Text

ISOCENTER OF FLOOR STAND

AutoCAD SHX Text

ORIENTATION POINT OF PATIENT TABLE AT FLOOR

AutoCAD SHX Text

15

AutoCAD SHX Text

AREA A: NO CEILING COMPONENTS NO CEILING COMPONENTS THAT EXTEND BELOW FINISHED CEILING AND ARE NOT PART OF THE SYSTEM MAY BE MOUNTED IN THIS AREA.

AutoCAD SHX Text

8

AutoCAD SHX Text

17

AutoCAD SHX Text

18

AutoCAD SHX Text

19

AutoCAD SHX Text

9

AutoCAD SHX Text

6

AutoCAD SHX Text

5

AutoCAD SHX Text

16

AutoCAD SHX Text

20

AutoCAD SHX Text

21

AutoCAD SHX Text

22

AutoCAD SHX Text

NON-SIEMENS (OEM) DISPLAY BOOMS CONTAINING SIEMENS MONITORS: IMPORTANT SAFETY CRITERIA: FAILURE TO MEET THE FOLLOWING REQUIREMENTS MAY RESULT IN RISK OF INJURY TO PATIENTS, PERSONNEL OR DAMAGE TO THE FAILURE TO MEET THE FOLLOWING REQUIREMENTS MAY RESULT IN RISK OF INJURY TO PATIENTS, PERSONNEL OR DAMAGE TO THE EQUIPMENT! 1) IT MUST BE POSSIBLE TO MANUALLY MOVE THE BOOM VERTICALLY WITH A FORCE LESS THAN 85 N (19 LBS) WHEN POSITIONING THE DISPLAY BOOM OVER THE PATIENT. 2) TO AVOID THE RISK OF CRUSHING PERSONS OR DAMAGING EQUIPMENT IN THE EVENT THAT THE ANGIOGRAPHY SYSTEM COMES INTO CONTACT WITH THE DISPLAY BOOM, IT MUST BE POSSIBLE TO PUSH THE BOOM AWAY IN A HORIZONTAL DIRECTION WITH A FORCE LESS THAN 50 N (11 LBS). 3) MOTORIZED, HEIGHT-ADJUSTABLE DISPLAY BOOMS WHICH CANNOT MANUALLY BE PUSHED AWAY MAY NOT BE USED. DELIVERY AND INSTALLATION: IT IS RECOMMENDED THAT INSTALLATION OF 3RD PARTY DISPLAY BOOMS BE COORDINATED WITH THE INSTALLATION OF THE SIEMENS SYSTEM. IN ORDER TO ENSURE THE SIMULTANEOUS INSTALLATION OF THE SYSTEM AND THE DISPLAY BOOM, THE CUSTOMER SHOULD TAKE STEPS EARLY IN THE PLANNING PROCESS TO ENSURE THAT THE BOOM MANUFACTURER'S LEAD TIME CAN BE COORDINATED WITH THE DELIVERY OF THE SIEMENS EQUIPMENT. THE THIRD-PARTY MANUFACTURER IS RESPONSIBLE FOR THE INSTALLATION, MAINTENANCE, AND SERVICE OF THE DISPLAY BOOM(S). THE THIRD-PARTY MANUFACTURER IS RESPONSIBLE FOR INSTALLING THE SIEMENS COMPONENTS IN THE DISPLAY BOOM IN ACCORDANCE WITH SIEMENS SPECIFICATIONS. SIEMENS ASSUMES NO RESPONSIBILITY FOR ANY DAMAGE TO SIEMENS COMPONENTS WHICH ARE NOT INSTALLED IN ACCORDANCE WITH SIEMENS SPECIFICATIONS. SIEMENS TECHNICIANS MUST BE GIVEN INSTRUCTIONS AND/OR TRAINING AS APPROPRIATE BY THE 3RD PARTY MANUFACTURER FOR MAINTENANCE/SERVICE OF THE SIEMENS COMPONENTS (I.E. DISPLAY, CABLES), OR A TECHNICIAN FROM THE THIRD-PARTY MANUFACTURER MUST BE PRESENT WHENEVER ANY SERVICE WORK IS PERFORMED.

AutoCAD SHX Text

SIEMENS LARGE DISPLAY MOUNTED ON CUSTOMER DISPLAY BOOM

AutoCAD SHX Text

7

AutoCAD SHX Text

CEILING HEIGHT RANGE

AutoCAD SHX Text

RECOMMENDED CEILING HEIGHT

AutoCAD SHX Text

9'-1 1/16" - 10'-2"

AutoCAD SHX Text

9'-6"

AutoCAD SHX Text

TYPICAL REV. 3

AutoCAD SHX Text

-ISSUE BLOCK-

AutoCAD SHX Text

DESCRIPTION

AutoCAD SHX Text

DATE

AutoCAD SHX Text

SYM

AutoCAD SHX Text

IT IS RECOMMENDED THAT THE SIEMENS DRAWINGS BE INCORPORATED WITH THE CONSTRUCTION

AutoCAD SHX Text

THIS DRAWING IS DESIGNED TO CONFORM TO FEATURES AND EQUIPMENT REQUIREMENTS PRESENTED

AutoCAD SHX Text

AT THE TIME OF THEIR PREPARATION. SINCE BOTH THESE FACTORS ARE SUBJECT TO DESIGN

AutoCAD SHX Text

MODIFICATION, THEY ARE NOT TO BE USED FOR CONSTRUCTION PURPOSES.

AutoCAD SHX Text

DOCUMENTS FOR REFERENCE.

AutoCAD SHX Text

THIS DRAWING DOES NOT PROVIDE RADIATION SHIELDING REQUIREMENTS FOR X-RAY AND ASSOCIATED

AutoCAD SHX Text

EQUIPMENT. THE CUSTOMER IS RESPONSIBLE FOR CONSULTING WITH A REGISTERED RADIATION

AutoCAD SHX Text

PHYSICIST TO SPECIFY RADIATION PROTECTION.

AutoCAD SHX Text

ALL DIMENSIONS SHOWN ON THIS DRAWING ARE FROM FINISHED SURFACES.

AutoCAD SHX Text

THIS SET OF PLANS REPRESENTS A COMPLETE SET OF DETAILS AND SHOULD NOT BE SEPARATED.

AutoCAD SHX Text

ALL RIGHTS ARE RESERVED.

AutoCAD SHX Text

STATE AGENCY REVIEW

AutoCAD SHX Text

PRIOR TO SIEMENS EQUIPMENT INSTALLATION, APPROVAL OF CONSTRUCTION OR STRUCTURAL MODIFICATIONS UTILIZING X-RAY FOR DIAGNOSTIC OR THERAPEUTIC PURPOSES, MUST BE OBTAINED BY THE CUSTOMER FROM THE APPROPRIATE STATE AGENCY, IF APPLICABLE.

AutoCAD SHX Text

ARCHITECTURAL EQUIPMENT PLAN

AutoCAD SHX Text

SCALE: 1/4" = 1'-0"

AutoCAD SHX Text

ARCHITECTURAL NOTES

AutoCAD SHX Text

1) ALL PRELIMINARY EQUIPMENT LAYOUTS SUBMITTED BY SIEMENS HEALTHCARE ARE BASED ON THE RECOMMENDED SPACE NECESSARY FOR THE OPERATION AND SERVICEABILITY OF THE EQUIPMENT BEING PROPOSED. SIEMENS WILL NOT SUBMIT AN EQUIPMENT LAYOUT THAT IS NOT IN THE BEST INTEREST OF BOTH THE CUSTOMER AND SIEMENS. ALL EQUIPMENT LAYOUTS ARE BASED EITHER ON AN ACTUAL SITE SURVEY OR ARCHITECTURAL DRAWINGS SUPPLIED TO SIEMENS. SIEMENS WILL NOT BE RESPONSIBLE FOR ANY ALTERATIONS THAT ENCROACH WITHIN DESIGNATED SAFETY AND SERVICE CLEARANCE ZONES AS INDICATED ON DRAWINGS (I.E.. PIPE CHASES, VENTILATION DUCTS, CASEWORK, AND SOFFITS, ETC.) MADE BY THE CUSTOMER OR REQUIRED BY A CUSTOMER'S ARCHITECTURAL FIRM ONCE PRELIMINARY DRAWINGS HAVE BEEN SUBMITTED AND APPROVED. DO NOT ALTER ANY SPECIFICATIONS AND/OR DIMENSIONS WITHOUT CONTACTING AND RECEIVING WRITTEN CONFIRMATION FROM SIEMENS PROJECT MANAGER. 2) SIEMENS HEALTHCARE IS NOT AN ARCHITECTURAL OR ENGINEERING FIRM. DRAWINGS SUPPLIED BY SIEMENS ARE NOT CONSTRUCTION DRAWINGS. THEREFORE, THESE DRAWINGS ARE TO BE USED ONLY FOR INFORMATION TO COMPLEMENT ACTUAL CONSTRUCTION DRAWINGS AVAILABLE FROM A CUSTOMER APPOINTED ARCHITECTURAL REPRESENTATIVE OR A CUSTOMER'S ENGINEERING DESIGN GROUP. THE CUSTOMER'S ARCHITECT AND GENERAL CONTRACTOR SHALL BE ULTIMATELY RESPONSIBLE FOR COMPLIANCE WITH ALL APPLICABLE CODES AND PROFESSIONAL DESIGN REQUIREMENTS INCLUDING OSHA/NEC SAFETY CLEARANCE REQUIRMENTS IN ADDITION TO SIEMENS-REQUIRED SAFETY/SERVICE CLEARANCES SHOWN. 3) THE CUSTOMER IS RESPONSIBLE FOR ALL ROOM AND AREA PREPARATION COSTS, PROFESSIONAL FEES, PERMITS, REPORTS, AND INSPECTION FEES. 4) EQUIPMENT WARRANTIES, EXPRESSED OR IMPLIED ON THE PART OF SIEMENS SHALL BE CONTINGENT UPON STRICT COMPLIANCE WITH THE ARCHITECTURAL, STRUCTURAL, ELECTRICAL, MECHANICAL AND RECOMMENDATIONS AND REQUIREMENTS CONTAINED IN THESE DRAWINGS, UNLESS SPECIFIED OTHERWISE. 5) ALL DIMENSIONS SHOWN ARE FROM FINISHED SURFACES UNLESS SPECIFIED OTHERWISE. 6) THIS DRAWING DOES NOT PROVIDE RADIATION SHIELDING REQUIREMENTS FOR X-RAY AND ASSOCIATED EQUIPMENT. THE CUSTOMER IS RESPONSIBLE FOR CONSULTING WITH A REGISTERED RADIATION PHYSICIST. ACTUAL PROTECTION REQUIREMENTS SHALL BE SPECIFIED BY A REGISTERED RADIATION PHYSICIST AT CUSTOMER'S ENGAGEMENT AND EXPENSE. RESPONSIBILITY FOR ALL INFORMATION AS TO THE ROOM LOCATION, USE, AND NUMBER OF ANTICIPATED EXAMINATIONS TO BE PERFORMED PER TIME PERIOD SHALL BE PROVIDED TO THE PHYSICIST BY THE CUSTOMER. THE CUSTOMER SHALL FURTHER TAKE ALL RESPONSIBILITY IN THE COMMUNICATION AND COORDINATION OF ACTIVITIES OF THE RADIATION PHYSICIST AND THE ARCHITECTURAL REPRESENTATIVE. 7) SIEMENS HEALTHCARE SHALL BE RESPONSIBLE FOR SIEMENS EQUIPMENT INSTALLATION, CALIBRATION, CONNECTION AND INSTALLATION OF SIEMENS PROVIDED CABLES. THE CUSTOMER/ELECTRICAL CONTRACTOR IS RESPONSIBLE FOR TERMINATIONS OF CUSTOMER/ELECTRICAL CONTRACTOR-SUPPLIED CABLES TO SIEMENS EQUIPMENT. IN THE EVENT THAT SPECIFIC TRADE RULES OR LICENSE REQUIREMENTS PROHIBIT THIS, THE CUSTOMER SHALL INITIATE THE SERVICES OF APPROVED OTHER CONTRACTORS AND PAY FOR SELECTED, APPROVED PARTIES TO PERFORM THIS WORK WITH SUPERVISION PROVIDED BY SIEMENS. CALIBRATION WHEN ACCOMPLISHED OUTSIDE OF NORMAL INSTALLATION SEQUENCES DUE TO CONTRACTOR OR TRADE RULE ACTIONS OR REQUIREMENTS SHALL BE SUPPORTED BY, CHARGED TO, AND ACCEPTED BY THE CUSTOMER AS AN ADDITIONAL INSTALLATION EXPENSE. 8) THE CUSTOMER SHALL COORDINATE WITH SIEMENS PROJECT MANAGER THE LOCATIONS AND TRAVEL OF ALL ANCILLARY EQUIPMENT TO BE CEILING OR WALL MOUNTED (I.E.: O.R. LIGHTS, MEDICAL GAS COLUMNS, PHYSIOLOGICAL MONITORING INJECTORS, CRT PLATFORMS, SPRINKLER HEADS, SMOKE DETECTORS, ELECTRICAL OUTLETS, HVAC GRILLES, SPEAKERS, AND GENERAL ROOM LIGHTING, ETC.). 9) THE GENERAL CONTRACTOR/CUSTOMER SHALL BE RESPONSIBLE FOR ALL FINAL PAINT, TOUCH-UP AND ANY COSMETIC OR TRIM WORK WHICH NEEDS TO BE OR IS REQUIRED TO BE COMPLETED AFTER THE INSTALLATION OF THE SIEMENS EQUIPMENT AND ANY ASSOCIATED SUPPORT APPARATUS.

AutoCAD SHX Text

0.5mT

AutoCAD SHX Text

1.0mT

AutoCAD SHX Text

MAGNETIC FIELD PRECAUTIONS

AutoCAD SHX Text

0.05mT

AutoCAD SHX Text

0.05mT

AutoCAD SHX Text

0.2mT

AutoCAD SHX Text

(10 GAUSS)

AutoCAD SHX Text

(5 GAUSS)

AutoCAD SHX Text

(2 GAUSS)

AutoCAD SHX Text

(0.5 GAUSS)

AutoCAD SHX Text

(0.5 GAUSS)

AutoCAD SHX Text

THE PRESENCE OF MAGNETIC FIELDS IN THE VICINITY OF EQUIPMENT MAY HAVE AN ADVERSE EFFECT. IT IS THE CUSTOMER'S RESPONSIBILITY TO VERIFY THAT THE FOLLOWING VALUES ARE NOT EXCEEDED.

AutoCAD SHX Text

MAXIMUM ALLOWABLE MAGNETIC FIELD

AutoCAD SHX Text

DEVICES

AutoCAD SHX Text

COMPUTERS, MAGNETIC DISK DRIVES, OSCILLOSCOPES, PROCESSORS

AutoCAD SHX Text

X-RAY TUBES, B/W MONITORS, MAGNETIC DATA CARRIERS, DATA STORAGE DRIVES

AutoCAD SHX Text

SIEMENS CT SCANNERS

AutoCAD SHX Text

CRT MONITORS, SIEMENS LINEAR ACCELERATORS

AutoCAD SHX Text

X-RAY IMAGE INTENSIFIERS, GAMMA CAMERAS, PET/CYCLOTRON, OTHER LINEAR ACCELERATORS

AutoCAD SHX Text

MAGNETIC FIELDS SHOULD BE MEASURED PRIOR TO DELIVERY

AutoCAD SHX Text

TRANSPORT FRAME REQUIREMENTS

AutoCAD SHX Text

FLOOR STAND 80" 43" 73" 2,811 LBS.

AutoCAD SHX Text

C-ARM 103" 39" 72" 1,102 LBS.

AutoCAD SHX Text

LENGTH

AutoCAD SHX Text

WIDTH

AutoCAD SHX Text

HEIGHT

AutoCAD SHX Text

WEIGHT

AutoCAD SHX Text

FLOOR STAND 80" 57" 73" 2,811 LBS.

AutoCAD SHX Text

C-ARM 88" 53" 72" 1,102 LBS.

AutoCAD SHX Text

COMPONENT

AutoCAD SHX Text

TRANSVERSE CASTORS

AutoCAD SHX Text

LONGITUDINAL CASTORS

AutoCAD SHX Text

TEMPERATURE RANGE: -4° F TO 158° F RELATIVE HUMIDITY: 20% TO 95% WITHOUT CONDENSATION AIR PRESSURE: 700 hPa TO 1060 hPa

AutoCAD SHX Text

ENVIRONMENTAL CONDITIONS FOR TRANSPORT/STORAGE

AutoCAD SHX Text

THE "B10" FIXPOINT IS A THRU-FLOOR PENETRATION PROVIDED AS A MEANS OF CONNECTING A TABLE INJECTOR OR OTHER NON-SIEMENS ACCESSORIES AT THE TABLE FOR WHICH CABLE ROUTING THROUGH THE SIEMENS TABLE BASE WOULD BE PROHIBITED. THIS OPENING CAN BE ELIMINATED AS REQUIRED, OR IT CAN BE COMBINED INTO A CUSTOMER-SUPPLIED GAS/UTILITY BOX ON THE FLOOR. NOTE: THE NOTE: THE 2'-0" DISTANCE FROM TABLE ISOCENTER SHOWN HERE APPLIES TO A CABLE PENETRATION POINT ONLY. SEE DIAGRAM FOR SEE DIAGRAM FOR POSSIBLE BOX PLACEMENT AND HEIGHT OPTIONS. VALIDATE EXACT PLACEMENT WITH SIEMENS PROJECT MANAGER.

AutoCAD SHX Text

FINISHED CEILING

AutoCAD SHX Text

TYPICAL SYSTEM ELEVATION

AutoCAD SHX Text

NONE

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text

B10

AutoCAD SHX Text

T1

AutoCAD SHX Text

FLOOR STAND

AutoCAD SHX Text

PATIENT TABLE

AutoCAD SHX Text

DISPLAY SUSPENSION

AutoCAD SHX Text

6"

AutoCAD SHX Text

MAX.

AutoCAD SHX Text

MAX.

AutoCAD SHX Text

5'-0" MAX.

AutoCAD SHX Text

1

AutoCAD SHX Text

EQUIPMENT LEGEND

AutoCAD SHX Text

NO

AutoCAD SHX Text

DESCRIPTION

AutoCAD SHX Text

SMS

AutoCAD SHX Text

WEIGHT

AutoCAD SHX Text

BTU/HR

AutoCAD SHX Text

DIMENSIONS (INCHES)

AutoCAD SHX Text

REMARKS

AutoCAD SHX Text

SYM

AutoCAD SHX Text

(LBS)

AutoCAD SHX Text

TO AIR

AutoCAD SHX Text

W

AutoCAD SHX Text

D

AutoCAD SHX Text

H

AutoCAD SHX Text

1

AutoCAD SHX Text

-

AutoCAD SHX Text

CPC (CENTRAL POWER CONTROL)

AutoCAD SHX Text

3

AutoCAD SHX Text

N/A

AutoCAD SHX Text

9 5/8

AutoCAD SHX Text

4

AutoCAD SHX Text

2 1/2

AutoCAD SHX Text

ON CONTROL COUNTER

AutoCAD SHX Text

2

AutoCAD SHX Text

CR1

AutoCAD SHX Text

CONTROL INTERFACE BOARD

AutoCAD SHX Text

18

AutoCAD SHX Text

342

AutoCAD SHX Text

19 1/4

AutoCAD SHX Text

3 1/4

AutoCAD SHX Text

13 1/2

AutoCAD SHX Text

MTD. ON WALL

AutoCAD SHX Text

3

AutoCAD SHX Text

-

AutoCAD SHX Text

KEYBOARD

AutoCAD SHX Text

2.2

AutoCAD SHX Text

342

AutoCAD SHX Text

17 1/2

AutoCAD SHX Text

6 1/8

AutoCAD SHX Text

2 1/8

AutoCAD SHX Text

MTD. UNDER COUNTER OR ON CONSOLE

AutoCAD SHX Text

4

AutoCAD SHX Text

-

AutoCAD SHX Text

24" LIVE DISPLAY

AutoCAD SHX Text

19

AutoCAD SHX Text

232

AutoCAD SHX Text

22 5/8

AutoCAD SHX Text

9 5/8

AutoCAD SHX Text

21 3/4

AutoCAD SHX Text

ON COUNTER OR CONSOLE

AutoCAD SHX Text

5

AutoCAD SHX Text

IW2

AutoCAD SHX Text

INJECTOR WALL CONNECTION - CONTROL ROOM

AutoCAD SHX Text

18

AutoCAD SHX Text

342

AutoCAD SHX Text

20 1/4

AutoCAD SHX Text

4 3/4

AutoCAD SHX Text

13 3/8

AutoCAD SHX Text

MTD. ON WALL

AutoCAD SHX Text

6

AutoCAD SHX Text

-

AutoCAD SHX Text

TABLE CONTROL MODULES

AutoCAD SHX Text

20.2

AutoCAD SHX Text

---

AutoCAD SHX Text

35 3/8

AutoCAD SHX Text

8 3/4

AutoCAD SHX Text

3 1/2

AutoCAD SHX Text

ON TABLE OR TROLLEY

AutoCAD SHX Text

7

AutoCAD SHX Text

D1

AutoCAD SHX Text

55" LARGE DISPLAY - BOOM 1 (MONITOR ONLY) (OPTION)

AutoCAD SHX Text

90

AutoCAD SHX Text

1,706

AutoCAD SHX Text

49 3/4

AutoCAD SHX Text

5 1/4

AutoCAD SHX Text

29

AutoCAD SHX Text

OEM BOOM MOUNTED

AutoCAD SHX Text

8

AutoCAD SHX Text

R1

AutoCAD SHX Text

FLOOR STAND W/ MOUNTING PLATE

AutoCAD SHX Text

3,428

AutoCAD SHX Text

1,706

AutoCAD SHX Text

---

AutoCAD SHX Text

---

AutoCAD SHX Text

---

AutoCAD SHX Text

ROBOT FLOOR MOUNTED

AutoCAD SHX Text

9

AutoCAD SHX Text

T1

AutoCAD SHX Text

PATIENT TABLE

AutoCAD SHX Text

1,200

AutoCAD SHX Text

683

AutoCAD SHX Text

---

AutoCAD SHX Text

---

AutoCAD SHX Text

---

AutoCAD SHX Text

TABLE FLOOR MOUNTED

AutoCAD SHX Text

10

AutoCAD SHX Text

PU1

AutoCAD SHX Text

POLYDOROS A100 GENERATOR CABINET

AutoCAD SHX Text

723

AutoCAD SHX Text

3,412

AutoCAD SHX Text

31 1/2

AutoCAD SHX Text

17 1/8

AutoCAD SHX Text

87

AutoCAD SHX Text

FLOOR MOUNTED

AutoCAD SHX Text

11

AutoCAD SHX Text

CC

AutoCAD SHX Text

CABLE CABINET

AutoCAD SHX Text

265

AutoCAD SHX Text

---

AutoCAD SHX Text

31 1/2

AutoCAD SHX Text

17 1/8

AutoCAD SHX Text

87

AutoCAD SHX Text

FLOOR MOUNTED

AutoCAD SHX Text

12

AutoCAD SHX Text

SC1

AutoCAD SHX Text

SYSTEM CONTROL CABINET

AutoCAD SHX Text

870

AutoCAD SHX Text

10,236

AutoCAD SHX Text

39 1/2

AutoCAD SHX Text

25 1/2

AutoCAD SHX Text

74 3/4

AutoCAD SHX Text

FLOOR MOUNTED

AutoCAD SHX Text

13

AutoCAD SHX Text

RC

AutoCAD SHX Text

FLOOR STAND CONTROL CABINET

AutoCAD SHX Text

396

AutoCAD SHX Text

3,412

AutoCAD SHX Text

31 1/4

AutoCAD SHX Text

34

AutoCAD SHX Text

41 7/8

AutoCAD SHX Text

FLOOR MOUNTED

AutoCAD SHX Text

14

AutoCAD SHX Text

IS

AutoCAD SHX Text

AXIS IMAGE SYSTEM

AutoCAD SHX Text

290

AutoCAD SHX Text

3,753

AutoCAD SHX Text

23 3/4

AutoCAD SHX Text

37 1/4

AutoCAD SHX Text

28

AutoCAD SHX Text

MTD. ON CASTERS

AutoCAD SHX Text

15

AutoCAD SHX Text

CU1

AutoCAD SHX Text

TUBE COOLING UNIT

AutoCAD SHX Text

80

AutoCAD SHX Text

15,355

AutoCAD SHX Text

16 1/2

AutoCAD SHX Text

17 1/2

AutoCAD SHX Text

19

AutoCAD SHX Text

FLOOR OR SHELF MOUNTED

AutoCAD SHX Text

16

AutoCAD SHX Text

CU2

AutoCAD SHX Text

FD COOLER

AutoCAD SHX Text

55

AutoCAD SHX Text

1,979

AutoCAD SHX Text

23 5/8

AutoCAD SHX Text

19

AutoCAD SHX Text

11 3/4

AutoCAD SHX Text

FLOOR OR SHELF MOUNTED

AutoCAD SHX Text

17

AutoCAD SHX Text

-

AutoCAD SHX Text

INTERCOM POWER UNIT (OPTION)

AutoCAD SHX Text

---

AutoCAD SHX Text

---

AutoCAD SHX Text

6 3/4

AutoCAD SHX Text

5

AutoCAD SHX Text

1 3/8

AutoCAD SHX Text

ON COUNTER

AutoCAD SHX Text

18

AutoCAD SHX Text

-

AutoCAD SHX Text

INTERCOM MICROPHONE/LOUDSPEAKER (CONTROL ROOM) (OPTION)

AutoCAD SHX Text

---

AutoCAD SHX Text

---

AutoCAD SHX Text

4 1/2

AutoCAD SHX Text

9

AutoCAD SHX Text

2

AutoCAD SHX Text

ON COUNTER

AutoCAD SHX Text

19

AutoCAD SHX Text

IC2

AutoCAD SHX Text

INTERCOM LOUDSPEAKER (PROCEDURE ROOM) (OPTION)

AutoCAD SHX Text

---

AutoCAD SHX Text

---

AutoCAD SHX Text

3 1/4

AutoCAD SHX Text

2

AutoCAD SHX Text

6

AutoCAD SHX Text

WALL MOUNTED

AutoCAD SHX Text

20

AutoCAD SHX Text

UPS

AutoCAD SHX Text

EATON 9355 15KVA UPS AND BATTERY (OPTION)

AutoCAD SHX Text

587

AutoCAD SHX Text

8,134

AutoCAD SHX Text

12 3/4

AutoCAD SHX Text

33 1/2

AutoCAD SHX Text

47 3/4

AutoCAD SHX Text

SEE MFG REQUIREMENTS

AutoCAD SHX Text

21

AutoCAD SHX Text

-

AutoCAD SHX Text

EATON 9355 OUTPUT TRANSFORMER CABINET (OPTION)

AutoCAD SHX Text

535

AutoCAD SHX Text

---

AutoCAD SHX Text

20

AutoCAD SHX Text

34 1/8

AutoCAD SHX Text

66

AutoCAD SHX Text


AutoCAD SHX Text

22

AutoCAD SHX Text

RMP

AutoCAD SHX Text

EATON 9355 REMOTE PANEL MONITOR (OPTION)

AutoCAD SHX Text

---

AutoCAD SHX Text

---

AutoCAD SHX Text

5 7/8

AutoCAD SHX Text

1 5/8

AutoCAD SHX Text

4 7/8

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

1 7

ARTIS PHENO

16055

A-102ATTENTION:

RE

FE

RE

NC

E D

OC

UM

EN

T - N

OT

F

OR

C

ON

ST

RU

CT

IO

N

ATTENTION:

RE

FE

RE

NC

E D

OC

UM

EN

T - N

OT

F

OR

C

ON

ST

RU

CT

IO

N

AutoCAD SHX Text


AutoCAD SHX Text

AS NOTED

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

PROJECT #:

AutoCAD SHX Text

SHEET:

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text

REF. #:

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

SHEET OF

AutoCAD SHX Text

DATE:

AutoCAD SHX Text

SHEET OF

AutoCAD SHX Text

DRAWN BY:

AutoCAD SHX Text

DRAWN BY:

AutoCAD SHX Text

TYPICAL REV. 3

AutoCAD SHX Text

-ISSUE BLOCK-

AutoCAD SHX Text

DESCRIPTION

AutoCAD SHX Text

DATE

AutoCAD SHX Text

SYM

AutoCAD SHX Text

ARTIS PHENO

AutoCAD SHX Text

REV. 9

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

9'-1 1/16" - 10'-2"

AutoCAD SHX Text

9'-6"

AutoCAD SHX Text

SAFETY CLEARANCE

AutoCAD SHX Text

SAFETY/SERVICE CLEARANCE

AutoCAD SHX Text

CONTROL ROOM

AutoCAD SHX Text

PROCEDURE ROOM

AutoCAD SHX Text

EQUIP. ROOM

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

CEILING NOTES

AutoCAD SHX Text

1) ALL CEILING MOUNTED LIGHT FIXTURES, MECHANICAL REGISTERS AND SPRINKLER HEADS SHALL BE FLUSH WITH FINISHED CEILING, SHALL BE OUTSIDE OF ALL HATCHED AREAS AND SHALL BE SPECIFIED BY THE ARCHITECT OF RECORD AND SUBSEQUENT CONSULTING ENGINEERS. 2) THE ACTUAL CEILING DESIGN AND COORDINATION OF LIGHTING AND MECHANICAL SYSTEMS SHALL BE THE RESPONSIBILITY OF THE ARCHITECT OF RECORD AND HIS SUBSEQUENT CONSULTING ENGINEERS. 3) THE CUSTOMER/CONTRACTOR SHALL BE RESPONSIBLE FOR FABRICATING, SUPPLYING AND INSTALLING ALL LIGHT, MECHANICAL AND STRUCTURAL SUPPORTING SYSTEMS. SIEMENS MEDICAL SYSTEMS, INC. IS ONLY RESPONSIBLE FOR THE SUPPLYING, INSTALLING AND CALIBRATION OF SMS EQUIPMENT AS SPECIFIED ON THE EQUIPMENT SCHEDULE AS SHOWN ON SHEET A-101. 4) ALL ELECTRICAL AND STRUCTURAL SYSTEMS SHOWN ON THE REFLECTED CEILING PLAN HAVE BEEN COORDINATED WITH THE EQUIPMENT LOCATIONS AS SHOWN ON THE 1/4" SCALE ARCHITECTURAL EQUIPMENT PLAN (SHEET A-101). ANY CHANGES TO THE SMS EQUIPMENT CONFIGURATION AS SHOWN, DUE TO PLACEMENT OF LIGHTING, STRUCTURAL, ELECTRICAL AND MECHANICAL SYSTEMS, MUST BE APPROVED IN WRITING BY THE SMS PROJECT MANAGER PRIOR TO THE COMPLETION OF CONSTRUCTION DOCUMENTS.

AutoCAD SHX Text

INJECTOR WALL BOX (CR)

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text

NONE

AutoCAD SHX Text

CABLE INLET

AutoCAD SHX Text

A

AutoCAD SHX Text

A

AutoCAD SHX Text

9/16"

AutoCAD SHX Text

1/4"

AutoCAD SHX Text

NOTE: WALL MOUNTING SCREWS PROVIDED BY CONTRACTOR.

AutoCAD SHX Text

1

AutoCAD SHX Text

SAFETY/SERVICE CLEARANCE PLAN

AutoCAD SHX Text

SCALE: 1/4" = 1'-0"

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

2 7

ARTIS PHENO

16055

S-101ATTENTION:

RE

FE

RE

NC

E D

OC

UM

EN

T - N

OT

F

OR

C

ON

ST

RU

CT

IO

N

FLOOR STAND PLATE

FLOOR STAND NOTES:

A - A

A

A

No scale

ATTENTION:

RE

FE

RE

NC

E D

OC

UM

EN

T - N

OT

F

OR

C

ON

ST

RU

CT

IO

N

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

9'-1 1/16" - 10'-2"

AutoCAD SHX Text

9'-6"

AutoCAD SHX Text

S-101

AutoCAD SHX Text

2

AutoCAD SHX Text

S-101

AutoCAD SHX Text

4

AutoCAD SHX Text

S-101

AutoCAD SHX Text

5

AutoCAD SHX Text

S-101

AutoCAD SHX Text

2

AutoCAD SHX Text

S-101

AutoCAD SHX Text

3

AutoCAD SHX Text

S-101

AutoCAD SHX Text

6

AutoCAD SHX Text

S-101

AutoCAD SHX Text

1

AutoCAD SHX Text

S-101

AutoCAD SHX Text

7

AutoCAD SHX Text

CONTRACTOR TO SUPPLY AND INSTALL BACKING FLUSH MOUNTED FOR MOUNTING ELECTRONIC CABINETS. SEE ELECTRONIC CABINET INSTALLATION DETAIL THIS SHEET.

AutoCAD SHX Text

NOTE: FOR ALL WEIGHTS AND SIZES OF EQUIPMENT SHOWN ON THIS PLAN PLEASE REFER TO THE EQUIPMENT LEGEND ON SHEET A-101.

AutoCAD SHX Text

CONTROL ROOM

AutoCAD SHX Text

PROCEDURE ROOM

AutoCAD SHX Text

EQUIP. ROOM

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

A-102

AutoCAD SHX Text

1

AutoCAD SHX Text


AutoCAD SHX Text

AS NOTED

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

PROJECT #:

AutoCAD SHX Text

SHEET:

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text

REF. #:

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

SHEET OF

AutoCAD SHX Text

DATE:

AutoCAD SHX Text

SHEET OF

AutoCAD SHX Text

DRAWN BY:

AutoCAD SHX Text

DRAWN BY:

AutoCAD SHX Text

TYPICAL REV. 3

AutoCAD SHX Text

-ISSUE BLOCK-

AutoCAD SHX Text

DESCRIPTION

AutoCAD SHX Text

DATE

AutoCAD SHX Text

SYM

AutoCAD SHX Text

ARTIS PHENO

AutoCAD SHX Text

REV. 9

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

STRUCTURAL NOTES

AutoCAD SHX Text

1) THE CUSTOMER/CONTRACTOR SHALL FURNISH AND INSTALL ALL STRUCTURAL SUPPORT MEMBERS AND NEEDED HARDWARE FOR THE INSTALLATION OF THE SIEMENS EQUIPMENT. 2) THE OVERHEAD STRUCTURAL SUPPORT SYSTEM SHALL BE FIXED, RIGID AND BRACED FOR SWAY. 3) ALL STRUCTURAL SUPPORT MEMBERS SHALL BE TRUE, SQUARE, LEVEL, PARALLEL AND COPLANAR WITH RESPECT TO EACH OTHER, WITH A HORIZONTAL STRUCTURAL SUPPORT MEMBER TO BE LOCATED AND SET WITH A TRANSIT. 4) ALL STRUCTURAL SUPPORT DETAILS SHOWN ARE SAMPLE DETAILS BASED UPON TYPICAL AND STANDARD BUILDING PRACTICES AND ARE NOT INTENDED AS ACTUAL CONSTRUCTION DETAILS. ALL CONSTRUCTION DETAILS AND SUPPORT CALCULATIONS SHALL BE PREPARED BY A PROFESSIONAL STRUCTURAL ENGINEER AT THE CUSTOMER'S EXPENSE. IN THE EVENT AN EXISTING SUPPORT SYSTEM IS TO BE USED, IT WILL BE THE CUSTOMER'S RESPONSIBILITY TO VERIFY THE INTEGRITY OF THAT SYSTEM. 5) MOUNTING PLATES, FRAMES, AND HARDWARE SUPPLIED BY SIEMENS AS DETAILED IN THIS DRAWING SET ARE INSTALLED BY SIEMENS UNLESS OTHERWISE REQUIRED. ANY DEVIATION FROM THE PROVIDED MATERIALS OR MOUNTING METHODS MUST BE DESIGNED AND DOCUMENTED BY THE STRUCTURAL ENGINEER OF RECORD. ALTERNATE MOUNTING MATERIALS (I.E. ANCHORS, THREADED ROD, BACKING PLATES, ETC.) MUST BE SUPPLIED BY THE CUSTOMER/CONTRACTOR. SIEMENS MAY REQUIRE ASSISTANCE FROM THE CUSTOMER/CONTRACTOR WITH INSTALLATION WHEN UTILIZING ALTERNATE MOUNTING MATERIALS. 6) ALL CEILING FIXTURES (I.E. AIR SUPPLY GRILLES, AIR RETURN GRILLES, EXHAUST GRILLES, SPRINKLER HEADS, INCANDESCENT AND FLUORESCENT LIGHT FIXTURES, INTERCOM SPEAKERS, MEDICAL GAS COLUMNS, ETC.) SHALL BE INSTALLED FLUSH MOUNTED WITH THE FINISHED CEILING TO PROVIDE FREE AND UNRESTRICTED TRAVEL OF THE SMS CEILING MOUNTED EQUIPMENT. 7) THE BOTTOM SIDE OF THE UNISTRUT CEILING GRID AND ANY CEILING MOUNTED SUPPORT PLATES ARE TO BE INSTALLED FLUSH WITH THE FINISHED CEILING. THE CUSTOMER/CONTRACTOR SHALL ALSO PROVIDE COVERSTRIPS FOR THE UNISTRUT. 8) THE STRUCTURAL PLANNING AS SHOWN ON THE 1/4" STRUCTURAL PLAN HAS BEEN COORDINATED WITH THE EQUIPMENT LOCATION AS SHOWN ON THE 1/4" EQUIPMENT LAYOUT PLAN. FOR THIS REASON, ANY DEVIATIONS FROM THE STRUCTURAL PLANNING AS SHOWN MUST BE APPROVED BY SMS PLANNING DEPARTMENT. 9) THE STRUCTURAL ENGINEER OF RECORD SHALL BE RESPONSIBLE FOR THE DESIGN AND DETAIL OF FLOOR, WALL, AND CEILING STRUCTURES IN ACCORDANCE WITH THE STRUCTURAL INFORMATION SHOWN, AND LOCAL GOVERNING BUILDING CODES.

AutoCAD SHX Text

SCALE: 1/4" = 1'-0"

AutoCAD SHX Text

STRUCTURAL FLOOR PLAN

AutoCAD SHX Text

FLOOR LEVELNESS

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text

1/2"=1'-0"

AutoCAD SHX Text

THE MAXIMUM FLOOR UNEVENNESS OF THE BASE FLOOR IN THE CROSS-HATCHED AREA IS 5/32".

AutoCAD SHX Text

OUTSIDE CONTOUR OF THE FLOOR STAND (WITH COVER PANEL)

AutoCAD SHX Text

FLOOR STAND INSTALLATION PLATE

AutoCAD SHX Text

6

AutoCAD SHX Text

HEAD-END WALL

AutoCAD SHX Text

PATIENT LEFT-SIDE WALL

AutoCAD SHX Text

FLOOR LOADS

AutoCAD SHX Text

NONE

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text

2

AutoCAD SHX Text

1

AutoCAD SHX Text

3

AutoCAD SHX Text

4

AutoCAD SHX Text

6

AutoCAD SHX Text

7

AutoCAD SHX Text

8

AutoCAD SHX Text

9

AutoCAD SHX Text

10

AutoCAD SHX Text

11

AutoCAD SHX Text

12

AutoCAD SHX Text

5

AutoCAD SHX Text

0%%D

AutoCAD SHX Text

MOUNTING POINT

AutoCAD SHX Text

TENSILE FORCE (LBS.)

AutoCAD SHX Text

LATERAL FORCE (LBS.)

AutoCAD SHX Text

1

AutoCAD SHX Text

885

AutoCAD SHX Text

1,680

AutoCAD SHX Text

2

AutoCAD SHX Text

1,217

AutoCAD SHX Text

1,728

AutoCAD SHX Text

3

AutoCAD SHX Text

553

AutoCAD SHX Text

1,728

AutoCAD SHX Text

4

AutoCAD SHX Text

PRESSURE

AutoCAD SHX Text

1,534

AutoCAD SHX Text

5

AutoCAD SHX Text

PRESSURE

AutoCAD SHX Text

1,385

AutoCAD SHX Text

6

AutoCAD SHX Text

PRESSURE

AutoCAD SHX Text

1,345

AutoCAD SHX Text

7

AutoCAD SHX Text

553

AutoCAD SHX Text

1,084

AutoCAD SHX Text

8

AutoCAD SHX Text

885

AutoCAD SHX Text

1,006

AutoCAD SHX Text

9

AutoCAD SHX Text

1,217

AutoCAD SHX Text

1,084

AutoCAD SHX Text

10

AutoCAD SHX Text

1,992

AutoCAD SHX Text

1,345

AutoCAD SHX Text

11

AutoCAD SHX Text

1,992

AutoCAD SHX Text

1,385

AutoCAD SHX Text

12

AutoCAD SHX Text

1,992

AutoCAD SHX Text

1,534

AutoCAD SHX Text

EFFECTIVE FORCES:

AutoCAD SHX Text

MAXIMUM TENSILE FORCE OCCURS AT ±45 DEGREES.DUE TO THE ROTATIONAL RANGE OF THE FLOOR STAND, TENSILE FORCES CAN OCCUR AT EVERY ATTACHMENT POINT OF THE MOUNTING PLATE. MAXIMUM BENDING IN THE AREA OF THE FLOOR STAND INSTALLATION PLATE IS 3MM WHEN A VERTICAL FORCE OF 3,147 LBS. IS EXERTED.

AutoCAD SHX Text

MAX. TILTING MOMENTUM, M : 39,828 FT-LBS. 39,828 FT-LBS. MAX TORQUE, M : 28,027 FT-LBS. 28,027 FT-LBS. MAX HORIZONTAL FORCE, F : 4,047 LBS. 4,047 LBS. MAX VERTICAL FORCE, F : 5,395 LBS. 5,395 LBS. 5,395 LBS.

AutoCAD SHX Text

k

AutoCAD SHX Text

r

AutoCAD SHX Text

h

AutoCAD SHX Text

v

AutoCAD SHX Text

F

AutoCAD SHX Text

h

AutoCAD SHX Text

M

AutoCAD SHX Text

r

AutoCAD SHX Text

M

AutoCAD SHX Text

k

AutoCAD SHX Text

F

AutoCAD SHX Text

v

AutoCAD SHX Text

MAX. CONCRETE COMPRESSION: 0.08% 0.08% MAX. CONCRETE COMPRESSION STRESS: 0.519 LBS/MM 0.519 LBS/MM RESULTING TENSILE FORCE: 10,879 LBS. 10,879 LBS. RESULTING COMPRESSIVE FORCE: 15,734 LBS. 15,734 LBS.

AutoCAD SHX Text

ASSUMING A 2,733 LB. FLOOR STAND PLUS 397 LB. C-ARM THE SPECIFICATIONS INCLUDE STATIC AND DYNAMIC FORCES MAX. TENSILE FORCE AT ±45 DEG.

AutoCAD SHX Text

*

AutoCAD SHX Text

*

AutoCAD SHX Text

*

AutoCAD SHX Text

2

AutoCAD SHX Text

2

AutoCAD SHX Text

SEAL CONTINUSLY WITH HYGIENIC-GRADE SILICONE

AutoCAD SHX Text

FASTENING OF STAND MOUNTING PLATE TO FLOOR (12 POINTS)

AutoCAD SHX Text

1

AutoCAD SHX Text

3

AutoCAD SHX Text

3

AutoCAD SHX Text

FLOOR COVERING

AutoCAD SHX Text

4

AutoCAD SHX Text

4

AutoCAD SHX Text

5

AutoCAD SHX Text

5

AutoCAD SHX Text

2

AutoCAD SHX Text

6

AutoCAD SHX Text

SOLID CONCRETE (MIN. C20/25 REQUIRED)

AutoCAD SHX Text

6

AutoCAD SHX Text

7

AutoCAD SHX Text

FASTENING PLATE SUPPLIED BY SIEMENS *

AutoCAD SHX Text

7

AutoCAD SHX Text

QUICK-POUR MORTAR

AutoCAD SHX Text

THREADED STUDS M20X500, 8.8

AutoCAD SHX Text

THROUGH-BOLT INSTALLATION OF STAND MOUNTING PLATE

AutoCAD SHX Text

NONE

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text

1

AutoCAD SHX Text

LOAD ON EACH MOUNTING POINT MAX. TENSILE FORCE SEE "STATIC FLOOR" DETAIL. FLOOR MOUNTING USING STUDS (THREADED BARS) THROUGH THE CEILING OF THE ROOM BELOW. (INCLUDED IN SHIPMENT)

AutoCAD SHX Text

* NOTE: UNDER OR IN-FLOOR REINFORCING FOR THE FLOOR STAND MOUNTING PLATE MUST BE DESIGNED BY THE STRUCTURAL ENGINEER OF RECORD AND FABRICATED/INSTALLED BY CUSTOMER/CONTRACTOR.

AutoCAD SHX Text

7

AutoCAD SHX Text

IF CONDITIONS REQUIRE THREADED RODS LONGER THAN THE 500MM SIEMENS-SUPPLIED RODS, CUSTOMER/ CONTRACTOR MUST SUPPLY.

AutoCAD SHX Text

NOTE: FOR SITES WITH FOR SITES WITH CORRUGATED OR WAFFLE SLABS CREATING VOIDS BETWEEN THE SLAB AND UNDER-FLOOR REINFORCING STEEL, THE VOIDS MUST BE FILLED AS REQUIRED OR THE UNDER-FLOOR STEEL BE SUFFICIENTLY STIFF TO MAINTAIN INTEGRITY IN THE AREA OF THE VOIDS WHEN THE THREADED ROD NUTS ARE TORQUED TO 273 FT-LBS AT EACH ANCHOR POINT. ALL UNDER-FLOOR REINFORCING MUST BE DESIGNED BY THE STRUCTURAL ENGINEER OF RECORD. ANY REQUIRED DRILLING OF CUSTOMER/CONTRACTOR- SUPPLIED UNDER FLOOR REINFORCING STEEL MUST BE PERFORMED BY CUSTOMER/CONTRACTOR IN COORDINATION WITH SIEMENS INSTALLATION ENGINEER.

AutoCAD SHX Text

3

AutoCAD SHX Text

INSTALLATION DIRECTLY ON SOLID CONCRETE

AutoCAD SHX Text

*3

AutoCAD SHX Text

*2

AutoCAD SHX Text

*1

AutoCAD SHX Text

*1

AutoCAD SHX Text

SECTION A-D

AutoCAD SHX Text

D

AutoCAD SHX Text

A

AutoCAD SHX Text

HEAD END

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text

NONE

AutoCAD SHX Text

TABLE MOUNTING PLATE

AutoCAD SHX Text

*3

AutoCAD SHX Text

SOLID CONCRETE

AutoCAD SHX Text

MAX. TENSILE FORCE PER MOUNTING POINT: 1,259 LBS. MAX. TENSILE FORCE PER MOUNTING POINT: 1,259 LBS. *2 OPENING IN INSTALLATION PLATE *3 CABLE OPENING IN THE FLOOR (OFF CENTER FROM TABLE O.P.) *4 PATIENT TABLE ORIENTATION POINT

AutoCAD SHX Text

INSTALLATION PLATE SUPPLIED AND INSTALLED BY SIEMENS

AutoCAD SHX Text

*4

AutoCAD SHX Text

*1

AutoCAD SHX Text

MOUNTING USING (4) HILTI HEAVY-DUTY EXPANSION BOLTS, HSL-3 M12/25, SUPPLIED BY SIEMENS. MINIMUM CONCRETE QUALITY IS C20/25.

AutoCAD SHX Text

4

AutoCAD SHX Text

DETAIL Y

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text

NONE

AutoCAD SHX Text

TABLE INSTALLATION PLATE WITH THREADED RODS

AutoCAD SHX Text

FLOOR COVERING

AutoCAD SHX Text

INSULATION PARTS

AutoCAD SHX Text

Y

AutoCAD SHX Text

SOLID CONCRETE

AutoCAD SHX Text

INSTALLATION PLATE

AutoCAD SHX Text

TABLE MOUNTING PLATE

AutoCAD SHX Text

CABLE OPENING IN FLOOR EITHER 5" BARE CONCRETE CORE, OR 6" CONDUIT DEPENDING LOCAL REQUIREMENTS.

AutoCAD SHX Text

SEAL CONTINUOUSLY WITH HYGIENIC-GRADE SILICONE

AutoCAD SHX Text

M12 THREADED RODS (ISO 8.8 HARDNESS) SUPPLIED BY CUSTOMER/CONTRACTOR.

AutoCAD SHX Text

5

AutoCAD SHX Text

CONTROL INTERFACE BOX

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text

NONE

AutoCAD SHX Text

CABLE INLET

AutoCAD SHX Text

A

AutoCAD SHX Text

A

AutoCAD SHX Text

NOTE: WALL MOUNTING SCREWS PROVIDED BY CONTRACTOR.

AutoCAD SHX Text

7

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text

NONE

AutoCAD SHX Text

ELECTRONIC CABINET INSTALLATION

AutoCAD SHX Text

WALL ATTACH BRACKETS (9/32" MOUNTING HOLES) SUPPLIED BY SIEMENS

AutoCAD SHX Text

6'-4"

AutoCAD SHX Text

35 1/2"

AutoCAD SHX Text

7'-3 7/8"

AutoCAD SHX Text

FLOOR LINE

AutoCAD SHX Text

4'-11"

AutoCAD SHX Text

GENERATOR

AutoCAD SHX Text

(PU1)

AutoCAD SHX Text

CABLE

AutoCAD SHX Text

CABINET

AutoCAD SHX Text

SYSTEM CABINET

AutoCAD SHX Text

(SC1)

AutoCAD SHX Text

12" MINIMUM CLEARANCE REQUIRED ABOVE THE CABINETS FOR EXHAUST AIR.

AutoCAD SHX Text

WALL BACKING AND ANCHOR SCREWS AT TOP OF ELECTRONIC CABINETS FOR WALL ANCHORING SUPPLIED AND INSTALLED BY CUSTOMER/CONTRACTOR.

AutoCAD SHX Text

AIR INTAKE (MAINTAIN 6" CLEARANCE)

AutoCAD SHX Text

EXHAUST AIR

AutoCAD SHX Text

1

AutoCAD SHX Text

(OPTION)

AutoCAD SHX Text

27 9/16"

AutoCAD SHX Text

4"

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

3 7

ARTIS PHENO

16055

E-101ATTENTION:

RE

FE

RE

NC

E D

OC

UM

EN

T - N

OT

F

OR

C

ON

ST

RU

CT

IO

N

ATTENTION:

RE

FE

RE

NC

E D

OC

UM

EN

T - N

OT

F

OR

C

ON

ST

RU

CT

IO

N

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

9'-1 1/16" - 10'-2"

AutoCAD SHX Text

9'-6"

AutoCAD SHX Text


AutoCAD SHX Text

AS NOTED

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

PROJECT #:

AutoCAD SHX Text

SHEET:

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text

REF. #:

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

SHEET OF

AutoCAD SHX Text

DATE:

AutoCAD SHX Text

SHEET OF

AutoCAD SHX Text

DRAWN BY:

AutoCAD SHX Text

DRAWN BY:

AutoCAD SHX Text

TYPICAL REV. 3

AutoCAD SHX Text

-ISSUE BLOCK-

AutoCAD SHX Text

DESCRIPTION

AutoCAD SHX Text

DATE

AutoCAD SHX Text

SYM

AutoCAD SHX Text

ARTIS PHENO

AutoCAD SHX Text

REV. 9

AutoCAD SHX Text

SD

AutoCAD SHX Text

XF1

AutoCAD SHX Text

30

AutoCAD SHX Text

MAIN POWER SUPPLY

AutoCAD SHX Text

1

AutoCAD SHX Text

DS

AutoCAD SHX Text

E-501

AutoCAD SHX Text

1

AutoCAD SHX Text

CONTROL ROOM

AutoCAD SHX Text

PROCEDURE ROOM

AutoCAD SHX Text

EQUIP. ROOM

AutoCAD SHX Text

9

AutoCAD SHX Text

9

AutoCAD SHX Text

10

AutoCAD SHX Text

11

AutoCAD SHX Text

EPO

AutoCAD SHX Text


AutoCAD SHX Text

2

AutoCAD SHX Text


AutoCAD SHX Text

37

AutoCAD SHX Text

MP

AutoCAD SHX Text

B10

AutoCAD SHX Text

T1

AutoCAD SHX Text

VD3

AutoCAD SHX Text

R1

AutoCAD SHX Text

12

AutoCAD SHX Text

39

AutoCAD SHX Text

15

AutoCAD SHX Text

16

AutoCAD SHX Text

17

AutoCAD SHX Text

19

AutoCAD SHX Text

21

AutoCAD SHX Text

22

AutoCAD SHX Text

24

AutoCAD SHX Text

26

AutoCAD SHX Text

29

AutoCAD SHX Text

28

AutoCAD SHX Text

31

AutoCAD SHX Text

32

AutoCAD SHX Text

33

AutoCAD SHX Text

35

AutoCAD SHX Text

36

AutoCAD SHX Text

38

AutoCAD SHX Text

PU1

AutoCAD SHX Text

IS

AutoCAD SHX Text

IS2

AutoCAD SHX Text

IC2

AutoCAD SHX Text

IC

AutoCAD SHX Text

CR1

AutoCAD SHX Text

CRB

AutoCAD SHX Text

VD1

AutoCAD SHX Text

VD2

AutoCAD SHX Text

EPO

AutoCAD SHX Text

18

AutoCAD SHX Text

23

AutoCAD SHX Text

CC

AutoCAD SHX Text

SC

AutoCAD SHX Text

RC

AutoCAD SHX Text

CU1

AutoCAD SHX Text

CU2

AutoCAD SHX Text

40

AutoCAD SHX Text

IW2

AutoCAD SHX Text

HD1

AutoCAD SHX Text

20

AutoCAD SHX Text

34

AutoCAD SHX Text

EPO

AutoCAD SHX Text

CU3

AutoCAD SHX Text

3

AutoCAD SHX Text

SC1

AutoCAD SHX Text

4

AutoCAD SHX Text

5

AutoCAD SHX Text

6

AutoCAD SHX Text

RMP

AutoCAD SHX Text

7

AutoCAD SHX Text

8

AutoCAD SHX Text

UPS

AutoCAD SHX Text

CUSTOMER-SUPPLIED VIDEO SOURCES IN PROCEDURE ROOM FOR CONNECTION TO SIEMENS LARGE DISPLAY ARE LOCATED BY CUSTOMER IN COORDINATION WITH SIEMENS PROJECT MANAGER. CONTRACTOR TO PROVIDE A 12"X12" FLUSH PULL BOX IN WALL WITH 4" BUSHED OPENING IN CENTER FOR EACH SIEMENS-SUPPLIED VIDEO CONVERTER/SPLITTER BOX REQUIRING WALL INSTALLATION. PROVIDE A 110VAC WALL OUTLET ADJACENT TO EACH BOX (POTENTIAL QUANTITY UP TO (6) BOXES/OUTLETS). .

AutoCAD SHX Text

23

AutoCAD SHX Text

24

AutoCAD SHX Text

26

AutoCAD SHX Text

D1

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

ELECTRICAL NOTES

AutoCAD SHX Text

1) COMPLIANCE: ELECTRICAL WORK SHALL BE IN COMPLIANCE WITH THE NATIONAL ELECTRICAL CODE (NFPA-70), O.S.H.A. REGULATIONS, AS WELL AS APPLICABLE REGULATIONS OF CITY, COUNTY, STATE AND FEDERAL AGENCIES. PROVIDE MATERIALS AND EQUIPMENT THAT COMPLY WITH ANSI, IEEE AND NEMA STANDARDS AND ARE U.L. LISTED AND LABELED. THE CUSTOMER'S/CONTRACTOR'S WORK AND ALL EQUIPMENT INSTALLED SHALL COMPLY WITH THE CURRENT EDITION OF THE NATIONAL ELECTRICAL CODE ADOPTED/ENFORCED BY THE AUTHORITY HAVING JURISDICTION. 2) QUALITY ASSURANCE: THE CONTRACTOR SHALL VERIFY EXISTING CONDITIONS IN THE FIELD TO INSURE THAT THE NEW WORK WILL FIT INTO THE EXISTING STRUCTURE AS SHOWN ON THE DRAWINGS. SHOULD ANY CONDITIONS EXIST OR BE DISCOVERED THAT PREVENT THE INSTALLATION OF WORK AS SHOWN, THE CONTRACTOR SHALL NOTIFY THE OWNER'S REPRESENTATIVE PRIOR TO FABRICATION OF EQUIPMENT, OR THE PERFORMANCE OF ANY WORK THAT MAY BE AFFECTED. DO NOT ALTER DRAWINGS, DIMENSIONS, OR SPECIFICATIONS IN ANY WAY WITHOUT CONTACTING AND RECEIVING WRITTEN CONFIRMATION FROM SIEMENS PROJECT MANAGER. ALL DIMENSIONS ARE FROM FINISHED SURFACES. CONDUIT AND PULL BOXES TO BE INSTALLED BY THE CUSTOMER/CONTRACTOR WITH LOCATIONS BEING FIELD VERIFIED BY THE SIEMENS PROJECT MANAGER. 3) POWER SUPPLY SOURCE: POWER SUPPLIES FOR SIEMENS HEALTHCARE EQUIPMENT SHALL BE FROM A MEDICAL IMAGING PANEL OR BUILDING SERVICE EQUIPMENT THAT IS A GROUNDED 3 OR 4-WIRE 'WYE' SOURCE PER THE SPECIFIC EQUIPMENT OPERATION REQUIREMENTS. A DEDICATED CIRCUIT SHALL BE PROVIDED THAT IS KEPT ENTIRELY FREE AND INDEPENDENT OF ALL OTHER BUILDING WIRING. NO ELEVATORS, GENERATORS, PUMPS, HVAC OR SIMILAR EQUIPMENT SHALL BE CONNECTED TO THE SAME CIRCUIT OR MEDICAL IMAGING PANEL THAT SERVES THE SIEMENS HEALTHCARE EQUIPMENT. IF THE POWER SUPPLY SOURCE DOES NOT MEET THE SPECIFIC SIEMENS EQUIPMENT POWER REQUIREMENTS, THE CONTRACTOR SHALL PROVIDE THE NECESSARY EQUIPMENT REQUIRED TO ESTABLISH THE POWER SUPPLY IN ACCORDANCE WITH THE REQUIRED POWER SUPPLY PARAMETERS OF THE SIEMENS EQUIPMENT. THE CONTRACTOR SHALL COORDINATE THIS WORK WITH THE CUSTOMER AND/OR UTILITY COMPANY FIELD REPRESENTATIVE. 4) WORK FURNISHED BY CUSTOMER/CONTRACTOR: WORK NOT PROVIDED BY SIEMENS HEALTHCARE BUT SHOWN ON DRAWINGS TO BE FURNISHED AND INSTALLED BY CUSTOMER/CONTRACTOR INCLUDES, BUT IS NOT LIMITED TO, THE FOLLOWING, UNLESS NOTED OTHERWISE: ELECTRICAL RACEWAYS AND DUCTS, WIRING TROUGHS, PULL BOXES, CONDUITS, CIRCUIT BREAKERS, ACCESS PANELS, EMERGENCY OFF BUTTONS, DOOR SWITCHES, WARNING LIGHTS, WIRING, WIRING DEVICES, CONNECTORS, LIGHTING EQUIPMENT AND GROUNDING. 5) RACEWAY AND CONDUIT NOTES: ALL CONDUITS SHALL BE INSTALLED IN COMPLIANCE WITH THE CURRENT ENFORCED EDITION OF THE NATIONAL ELECTRICAL CODE. CONDUIT BODIES SHALL NOT BE USED. WHERE A CONDUIT ENTERS A BOX, FITTING, OR OTHER ENCLOSURE, AN INSULATED THROAT CONNECTOR SHALL BE PROVIDED TO PROTECT THE WIRE FROM ABRASION. ALL CONNECTORS FOR EMT SHALL BE COMPRESSION OR DOUBLE SET SCREW TYPE. KEEP RACEWAYS AT LEAST 6 INCHES AWAY FROM PARALLEL RUNS OF FLUES OR STEAM AND HOT WATER PIPES. INSTALL RACEWAY RUNS ABOVE WATER AND STEAM PIPES PROVIDED THAT CABLE RUN DISTANCES ARE MAINTAINED. USE TEMPORARY CLOSURES TO PREVENT FOREIGN MATTER FROM ENTERING RACEWAY. CONDUIT RUNS ARE SHOWN SCHEMATICALLY. INSTALL CONDUIT WITH A MINIMUM OF BENDS IN THE SHORTEST PRACTICAL DISTANCE CONSIDERING THE BUILDING CONSTRUCTION AND OBSTRUCTIONS, EXCEPT AS OTHERWISE INDICATED. THE CONTRACTOR SHALL MAKE CERTAIN THAT ANY CONDUIT/RACEWAY RUNS CONTAINING SIEMENS HEALTHCARE CABLES DO NOT EXCEED THE SPECIFIED MAXIMUM DISTANCES AS SHOWN ON THE ELECTRICAL DETAILS. LISTED CONDUIT SIZES FOR SIEMENS-SUPPLIED CABLES MUST BE MAINTAINED IN ORDER TO ENABLE THE TOTAL CABLE BUNDLE INCLUDING CONNECTORS TO BE PULLED THROUGH WITHOUT DAMAGE. PROVIDE ENCLOSED METAL WIRE DUCT RACEWAY SYSTEM WHERE SHOWN ON DRAWINGS WITH DIVIDERS TO SEPARATE THE DUCT INTO TWO OR THREE SEPARATE COMPARTMENTS AS SHOWN ON THE SIEMENS PLANS (FOR POWER AND SIEMENS HEALTHCARE CABLING). DIVIDERS AND CROSSOVER PIECES TO BE PROVIDED AS NECESSARY. THE CABLE TO CABLE AS WELL AS THE CIRCUIT TO CIRCUIT SEPARATION REQUIREMENT WAS EVALUATED DURING THE UL SYSTEM CERTIFICATION OF THE EQUIPMENT. ADDITIONAL SEPARATION OF THE SYSTEM CABLE ASSEMBLIES INTO SEPARATE OR PARTITIONED RACEWAYS, UNLESS OTHERWISE NOTED, IS NOT NECESSARY TO INSURE SEPARATION OF CIRCUITS. PROVIDE WIRE DUCT/RACEWAY WITH ACCESSIBLE REMOVABLE COVERS. LOCATIONS OF BUILDING MATERIAL OPENINGS (I.E. ACCESS PANELS) TO BE CUT IN FIELD ARE TO BE COORDINATED WITH THE DRAWING REQUIRMENTS AND BUILDING STRCTURE. THOSE THAT ARE NOT INDICATED OR INTERFER WITH BUILDING ELEMENTS SHALL BE COORDINATED WITH SIEMENS PROJECT MANAGER. ELECTRICAL PULL BOXES AND RACEWAY COVERS SHALL BE INSTALLED IN A MANNER TO ALLOW ACCESSIBILITY FOR INSTALLATION AND MAINTENANCE. CONTRACTORS MUST PROVIDE PULL STRINGS FOR ALL CONDUIT AND WIRE DUCT/RACEWAY. IN-FLOOR TRENCH DUCT AND FLUSH FLOOR BOXES SHALL BE PROVIDED WITH FULLY GASKETED REMOVABLE COVERS. WHEN JUNCTION BOXES AND WIRE DUCT/RACEWAY ARE MOUNTED HIGHER THAN 14 FEET ABOVE FINISHED FLOOR, THE ELECTRICAL CONTRACTOR SHALL PROVIDE TWO ELECTRICIANS TO HELP THE SIEMENS INSTALLERS PULL SIEMENS SUPPLIED CABLES AT CUSTOMER'S EXPENSE. WHEN JUNCTION WHEN JUNCTION BOXES AND WIRE DUCT/RACEWAY ARE MOUNTED ABOVE A HARD CEILING (I.E. SHEET ROCK), A 24" x 24" ACCESS PANEL IS REQUIRED AT EACH JUNCTION BOX AND WITHIN 2 FEET OF EACH RACEWAY TRANSITION (SUCH AS A 90 DEGREE ELBOW OR TEE) IN DUCT/RACEWAY. THERE MUST BE FREE AND CLEAR ACCESS TO JUNCTION BOXES AND WIRE DUCT/RACEWAY. WHEN ACCESS PANELS ARE LOCATED MORE THAN 3 FEET FROM JUNCTION BOXES AND WIRE DUCT/RACEWAY THE ELECTRICAL CONTRACTOR SHALL PROVIDE TWO ELECTRICIANS TO HELP SIEMENS INSTALLERS PULL SIEMENS SUPPLIED CABLES AT CUSTOMER'S EXPENSE. 6) WIRING: ALL WIRING INSTALLED SHALL BE 600 VOLT CLASS, STRANDED TYPE THHN/THWN-2, SINGLE CONDUCTOR ANNEALED COPPER FOR A MAXIMUM OPERATING TEMPERATURE OF 90° C (194° F), SIZED AS INDICATED, INSTALLED IN METAL RACEWAYS. THE CUSTOMER/CONTRACTOR SHALL LEAVE A MINIMUM 10 FEET OF WIRE TAILS AT ALL OUTLET POINTS WITH WIRE IDENTIFICATION TAGGED AT BOTH ENDS FOR FINAL CONNECTION BY THE CUSTOMER/ELECTRICAL CONTRACTOR. 7) SHORT CIRCUIT REQUIREMENTS: ALL CIRCUIT BREAKERS SUPPLIED FOR THE SIEMENS EQUIPMENT REQUIREMENTS SHALL BE RATED HIGHER THAN THE SHORT CIRCUIT AVAILABLE AT THE TERMINALS OF THE ELECTRICAL EQUIPMENT AS DETERMINED BY THE ENGINEER OF RECORD, BUT NOT LESS THAN 35,000A RMS SYMMETRICAL AT 480V, 3-PHASE, 60 HERTZ. THE CONTRACTOR SHALL OBTAIN THE CORRECT SHORT CIRCUIT CURRENT RATING OF ALL THE NEW EQUIPMENT FOR INSTALLATION FROM THE ENGINEER OF RECORD.

AutoCAD SHX Text

ELECTRICAL RACEWAY PLAN

AutoCAD SHX Text

SCALE: 1/4" = 1'-0"

AutoCAD SHX Text

CONDUIT LENGTH CALCULATIONS

AutoCAD SHX Text

IF SITE-SPECIFIC CONDITIONS EXCEED THE FOLLOWING ASSUMED VALUES, THEN ADDITIONAL LENGTH MUST BE SUBTRACTED BY THE ELECTRICAL CONTRACTOR FROM THE MAXIMUM CONDUIT LENGTHS LISTED.

AutoCAD SHX Text

IF DUCT LOCATIONS ARE ALTERED FROM THE SHOWN LAYOUT, IT IS THE ELECTRICAL CONTRACTOR'S RESPONSIBILITY TO RECALCULATE THE MAXIMUM CONDUIT LENGTHS.

AutoCAD SHX Text

ASSUMED VALUES USED IN CALCULATING STATED MAXIMUM CONDUIT LENGTHS: VERTICAL DUCTS - 12'-0" FLOOR PENETRATIONS - 3'-0"

AutoCAD SHX Text

SYSTEMS NETWORK (VERIFY WITH SMS PROJECT MANAGER).

AutoCAD SHX Text

ETHERNET CONNECTION TO CUSTOMER'S INFORMATION

AutoCAD SHX Text

ALL MAY NOT APPLY

AutoCAD SHX Text

110 VOLT, 20 AMP, HOSPITAL GRADE DUPLEX OUTLET

AutoCAD SHX Text

UNDER FLOOR DUCT

AutoCAD SHX Text

CEILING DUCT

AutoCAD SHX Text

TRENCHDUCT

AutoCAD SHX Text

SYMBOLS

AutoCAD SHX Text

OPENING IN ACCESS FLOORING

AutoCAD SHX Text

(EPO) EMERGENCY POWER OFF BUTTON

AutoCAD SHX Text

DOOR SAFETY SWITCH

AutoCAD SHX Text

WARNING LIGHT (X-RAY ON)

AutoCAD SHX Text

VERTICAL DUCT

AutoCAD SHX Text

PULLBOX IN (FLOOR/WALL/CEILING)

AutoCAD SHX Text

OPENING IN RACEWAY OR TRENCHDUCT

AutoCAD SHX Text

CIRCUIT BREAKER BY CUSTOMER/CONTRACTOR

AutoCAD SHX Text

DS

AutoCAD SHX Text

110 VOLT, 20 AMP, HOSPITAL GRADE QUAD OUTLET

AutoCAD SHX Text

SURFACE DUCT

AutoCAD SHX Text

ELECTRICAL LEGEND

AutoCAD SHX Text

SYM

AutoCAD SHX Text

SIZE

AutoCAD SHX Text

DESCRIPTION

AutoCAD SHX Text

REMARKS

AutoCAD SHX Text

SUPPLIED AND INSTALLED BY CUSTOMER/CONTRACTOR

AutoCAD SHX Text

B10

AutoCAD SHX Text

AS REQUIRED

AutoCAD SHX Text

PULL BOX MOUNTED BELOW FINISHED FLOOR WITH REMOVABLE BOTTOM COVER. PROVIDE 4" SLEEVE FROM BOX TO FLUSH WITH FINISHED FLOOR. PROVIDE STAINLESS STEEL WATERPROOF PLATE ON TOP OF CORED OPENING IN FLOOR.

AutoCAD SHX Text

TABLE, ACCESSORIES

AutoCAD SHX Text

CC

AutoCAD SHX Text

10" X 8"

AutoCAD SHX Text

BUSHED OPENING IN VERTICAL DUCT "VD1" COVER AT FLOOR LINE.

AutoCAD SHX Text

CABLE CABINET

AutoCAD SHX Text

CR1

AutoCAD SHX Text

3"

AutoCAD SHX Text

BUSHED OPENING IN TOP OF HORIZONTAL DUCT "HD1".

AutoCAD SHX Text

CONTROL ROOM DISTRIBUTOR

AutoCAD SHX Text

CRB

AutoCAD SHX Text

AS REQUIRED

AutoCAD SHX Text

PULL BOX MOUNTED BELOW FINISHED FLOOR WITH REMOVABLE BOTTOM COVER. FOR A SINGLE CONDUIT CONNECTION TO THIS BOX, PROVIDE A 3" CONDUIT THRU FLOOR. FOR MULTIPLE CONDUIT CONNECTIONS, PROVIDE (2) 4" CONDUITS THRU FLOOR. E.C. TO DESIGN TRANSITION TO SURFACE FLOOR DUCT AS REQUIRED.

AutoCAD SHX Text

CONTROL ROOM UNDER-FLOOR BOX

AutoCAD SHX Text

CU1

AutoCAD SHX Text

AS REQUIRED

AutoCAD SHX Text

PULL BOX MOUNTED FLUSH IN FINISHED WALL AT FLOOR LINE. PROVIDE BOX WITH REMOVABLE FRONT COVER AND (1) 4" BUSHING IN CENTER OF REMOVABLE COVER FOR CABLE EXIT. SEEPLAN FOR LOCATION.

AutoCAD SHX Text

TUBE COOLING UNIT

AutoCAD SHX Text

CU2

AutoCAD SHX Text

---

AutoCAD SHX Text

FIXED POINT DESIGNATION, SAME BOX AS "CU1".

AutoCAD SHX Text

FD COOLING UNIT

AutoCAD SHX Text

CU3

AutoCAD SHX Text

AS REQUIRED

AutoCAD SHX Text

PULL BOX MOUNTED BELOW FINISHED FLOOR WITH REMOVABLE BOTTOM COVER. PROVIDE 5" SLEEVE FROM BOX TO FLUSH WITH FINISHED FLOOR WITH BUSHING AT FLOOR LINE.

AutoCAD SHX Text

COOLING UNITS

AutoCAD SHX Text

D1

AutoCAD SHX Text

AS REQUIRED

AutoCAD SHX Text

PULL BOX MOUNTED ABOVE FINISHED CEILING WITH REMOVABLE BOTTOM COVER WITH 4" BUSHED OPENING.

AutoCAD SHX Text

LARGE DISPLAY

AutoCAD SHX Text

EPO

AutoCAD SHX Text

---

AutoCAD SHX Text

EMERGENCY OFF BUTTONS FOR CIRCUIT BREAKERS. EPO'S MUST PREVENT RESETTING OF CIRCUIT BREAKERS WHEN IN OFF POSITION. EPO'S MUST BE RECESSED OR SHIELDED. FINAL LOCATION DETERMINED BY CUSTOMER.

AutoCAD SHX Text

EMERGENCY POWER OFF

AutoCAD SHX Text

IC

AutoCAD SHX Text

AS REQUIRED

AutoCAD SHX Text

PULL BOX MOUNTED FLUSH IN FINISHED CEILING IN LOCATION COORDINATED WITH INTERCOM INSTALLATION. PROVIDE REMOVABLE BOTTOM COVER WITH 3/4" BUSHED OPENING.

AutoCAD SHX Text

INTERCOM MIC

AutoCAD SHX Text

IC2

AutoCAD SHX Text

AS REQUIRED

AutoCAD SHX Text

PULL BOX MOUNTED FLUSH IN FINISHED WALL AT A RECOMMENDED HEIGHT OF 6' AFF.

AutoCAD SHX Text

INTERCOM LOUDSPEAKER

AutoCAD SHX Text

IS

AutoCAD SHX Text

5"

AutoCAD SHX Text

BUSHED OPENING IN VERTICAL DUCT "VD2" COVER AT FLOOR LINE.

AutoCAD SHX Text

IMAGE SYSTEM

AutoCAD SHX Text

IS2

AutoCAD SHX Text

AS REQUIRED

AutoCAD SHX Text


AutoCAD SHX Text

IMAGE SYSTEM

AutoCAD SHX Text

IW2

AutoCAD SHX Text

3"

AutoCAD SHX Text

BUSHED OPENING IN TOP OF HORIZONTAL DUCT "HD1".

AutoCAD SHX Text

CONTROL RM INJ/CONTROLS

AutoCAD SHX Text

MP

AutoCAD SHX Text

---

AutoCAD SHX Text

MAIN PANEL WITH MAIN BREAKER. LOCATION DETERMINED BY CUSTOMER/CONTRACTOR. SEE "POWER SCHEDULE".

AutoCAD SHX Text

BREAKER PANEL

AutoCAD SHX Text

PU1

AutoCAD SHX Text

AS REQUIRED

AutoCAD SHX Text

PULL BOX MOUNTED FLUSH IN FINISHED WALL AT FLOOR LINE. PROVIDE BOX WITH REMOVABLE FRONT COVER WITH 4" BUSHED OPENING AT BOTTOM OF COVER.

AutoCAD SHX Text

GENERATOR

AutoCAD SHX Text

R1

AutoCAD SHX Text

AS REQUIRED

AutoCAD SHX Text

PULL BOX MOUNTED BELOW FINISHED FLOOR WITH REMOVABLE BOTTOM COVER. PROVIDE (2) 6" SLEEVES FROM BOX TO FLUSH WITH FINISHED FLOOR WITH BUSHING AT FLOOR LINE.

AutoCAD SHX Text

FLOOR STAND

AutoCAD SHX Text

RC

AutoCAD SHX Text

AS REQUIRED

AutoCAD SHX Text


AutoCAD SHX Text

FLOOR STAND CABINET

AutoCAD SHX Text

RMP

AutoCAD SHX Text

AS REQUIRED

AutoCAD SHX Text

PULL BOX (SINGLE GANG) MOUNTED FLUSH IN FINISHED WALL AT HEIGHT COORDINATED WITH UPS REMOTE MONITOR PANEL.

AutoCAD SHX Text

UPS REMOTE MONITOR PANEL

AutoCAD SHX Text

SC1

AutoCAD SHX Text

AS REQUIRED

AutoCAD SHX Text

PULL BOX MOUNTED FLUSH IN FINISHED WALL AT FLOOR LINE. PROVIDE BOX WITH REMOVABLE FRONT COVER WITH 4" BUSHED OPENING AT BOTTOM OF COVER.

AutoCAD SHX Text

SYSTEM CABINET

AutoCAD SHX Text

SC

AutoCAD SHX Text

AS REQUIRED

AutoCAD SHX Text

PULL BOX MOUNTED BELOW FINISHED FLOOR WITH REMOVABLE BOTTOM COVER. PROVIDE (2) 6" SLEEVES FROM BOX TO FLUSH WITH FINISHED FLOOR WITH BUSHINGS AT FLOOR LINE.

AutoCAD SHX Text

SYSTEM CABINET

AutoCAD SHX Text

T1

AutoCAD SHX Text

AS REQUIRED

AutoCAD SHX Text

PULL BOX MOUNTED BELOW FINISHED FLOOR WITH REMOVABLE BOTTOM COVER. IF LOCAL CODE ALLOWS, PROVIDE 5" BARE CONCRETE CORE THRU SLAB FROM BOX TO FINISHED FLOOR.OTHERWISE, PROVIDE A 6" CONDUIT THRU SLAB FROM BOX WITH A CONDUIT BUSHING FLUSHWITH FINISHED FLOOR. CONTACT SIEMENS PROJECT MANAGER.

AutoCAD SHX Text

TABLE

AutoCAD SHX Text

UPS

AutoCAD SHX Text

AS REQUIRED

AutoCAD SHX Text

PULL BOX MOUNTED FLUSH IN FINISHED WALL AT FLOOR LINE. PROVIDE BOX WITH REMOVABLE FRONT COVER WITH 4" BUSHED OPENING.

AutoCAD SHX Text

15KVA UPS

AutoCAD SHX Text

XF1

AutoCAD SHX Text

750VA

AutoCAD SHX Text

STEP-DOWN TRANSFORMER. SEE POWER SCHEDULE.

AutoCAD SHX Text

XFMR FOR TABLE OUTLET

AutoCAD SHX Text

HD1

AutoCAD SHX Text

3 1/2" X 10"

AutoCAD SHX Text

HORIZONTAL DUCT MOUNTED ON FINISHED WALL AT FLOOR LINE. PROVIDE DUCT WITH REMOVABLE FRONT COVER. CONNECT TO VERTICAL DUCT "VD2" AS SHOWN.

AutoCAD SHX Text

HORIZONTAL WALL DUCT

AutoCAD SHX Text

VD1

AutoCAD SHX Text

VD2

AutoCAD SHX Text

VD3

AutoCAD SHX Text

3 1/2" X 10"

AutoCAD SHX Text

VERTICAL DUCT MOUNTED FLUSH IN FINISHED WALL. BEGIN DUCT AT FLOOR LINE AND EXTEND UP WALL ABOVE FINISHED CEILING. PROVIDE JUNCTION BOX (SIZED BY E.C.) AT TOP OF DUCT FOR CONDUIT TRANSITIONS. IF REQUIRED BY LOCAL CODE, DIVIDE DUCT INTO (3) SECTIONS WITH METAL DIVIDERS.

AutoCAD SHX Text

VERTICAL DUCT

AutoCAD SHX Text

1

AutoCAD SHX Text

EC TO SIZE

AutoCAD SHX Text

CONDUIT FROM PANEL TO "MP"

AutoCAD SHX Text

SEE "POWER SCHEDULE"

AutoCAD SHX Text

2

AutoCAD SHX Text

EC TO SIZE

AutoCAD SHX Text

CONDUIT FROM "MP" TO "PU1"

AutoCAD SHX Text


AutoCAD SHX Text

3

AutoCAD SHX Text

EC TO SIZE

AutoCAD SHX Text

CONDUIT FROM "MP" TO "UPS" WITH FLEX CONDUIT FROM UPS BOX TO TERMINATION ON UPS CABINET.

AutoCAD SHX Text


AutoCAD SHX Text

4

AutoCAD SHX Text

EC TO SIZE

AutoCAD SHX Text

CONDUIT FROM "UPS" TO "SD" WITH FLEX CONDUIT FROM UPS BOX TO TERMINATION ON OUTPUT TRANSFORMER CABINET.

AutoCAD SHX Text


AutoCAD SHX Text

5

AutoCAD SHX Text

EC TO SIZE

AutoCAD SHX Text

CONDUIT FROM "SD" TO "SC1".

AutoCAD SHX Text


AutoCAD SHX Text

6

AutoCAD SHX Text

3/4"

AutoCAD SHX Text

CONDUIT FROM "UPS" TO "EPO" WITH FLEX CONDUIT FROM UPS BOX TO TERMINATION ON UPS CABINET.

AutoCAD SHX Text


AutoCAD SHX Text

7

AutoCAD SHX Text

3/4"

AutoCAD SHX Text

CONDUIT FROM "RMP" TO "UPS" WITH FLEX CONDUIT FROM UPS BOX TO TERMINATION ON UPS CABINET.

AutoCAD SHX Text


AutoCAD SHX Text

8

AutoCAD SHX Text

3/4"

AutoCAD SHX Text

CONDUIT FROM "MP" TO "EPO"

AutoCAD SHX Text


AutoCAD SHX Text

9

AutoCAD SHX Text

EC TO SIZE

AutoCAD SHX Text

CONDUIT FROM "EPO" TO "EPO"

AutoCAD SHX Text

10

AutoCAD SHX Text

EC TO SIZE

AutoCAD SHX Text

CONDUIT FROM "SC1" TO "WL"

AutoCAD SHX Text

11

AutoCAD SHX Text

EC TO SIZE

AutoCAD SHX Text

CONDUIT FROM "SC1" TO "DS"

AutoCAD SHX Text

12

AutoCAD SHX Text

EC TO SIZE

AutoCAD SHX Text

CONDUIT FROM "MP" TO "XF1" (OPTIONAL)

AutoCAD SHX Text

TABLE POWER OUTLET

AutoCAD SHX Text

13

AutoCAD SHX Text

2"

AutoCAD SHX Text

CONDUIT FROM "R1" TO "SC" (PU1) UNDER FLOOR

AutoCAD SHX Text

MAX. CONDUIT LENGTH 42'

AutoCAD SHX Text

14

AutoCAD SHX Text

(2) 3"

AutoCAD SHX Text

CONDUIT FROM "R1" TO "SC" (PU1) UNDER FLOOR

AutoCAD SHX Text


AutoCAD SHX Text

15

AutoCAD SHX Text

(2) 3"

AutoCAD SHX Text

CONDUIT FROM "R1" TO "SC" (SC1) UNDER FLOOR

AutoCAD SHX Text


AutoCAD SHX Text

16

AutoCAD SHX Text

3"

AutoCAD SHX Text

CONDUIT FROM "R1" TO "CU3" (CU1) UNDER FLOOR FOR LIQUID COOLING HOSES

AutoCAD SHX Text


AutoCAD SHX Text

17

AutoCAD SHX Text

2"

AutoCAD SHX Text

CONDUIT FROM "R1" TO "CU3" (CU2) UNDER FLOOR FOR LIQUID COOLING HOSES

AutoCAD SHX Text


AutoCAD SHX Text

18

AutoCAD SHX Text

3"

AutoCAD SHX Text

CONDUITS FROM "VD1" (SC1) TO "VD3" (CR1)

AutoCAD SHX Text


AutoCAD SHX Text

19

AutoCAD SHX Text

(2) 3"

AutoCAD SHX Text

CONDUIT FROM "SC" TO "T1" UNDER FLOOR

AutoCAD SHX Text


AutoCAD SHX Text

20

AutoCAD SHX Text

2"

AutoCAD SHX Text

CONDUIT FROM "VD1" (SC1) TO "CU1"

AutoCAD SHX Text


AutoCAD SHX Text

21

AutoCAD SHX Text

2 1/2"

AutoCAD SHX Text

CONDUIT FROM "SC" (SC1) TO "CU3" (CU2) UNDER FLOOR

AutoCAD SHX Text


AutoCAD SHX Text

22

AutoCAD SHX Text

3"

AutoCAD SHX Text

CONDUIT FROM "VD1" (SC1) TO "VD2" (IS)

AutoCAD SHX Text


AutoCAD SHX Text

23

AutoCAD SHX Text

3"

AutoCAD SHX Text

CONDUIT FROM "VD1" (SC1) TO "D1"

AutoCAD SHX Text


AutoCAD SHX Text

24

AutoCAD SHX Text

2"

AutoCAD SHX Text

CONDUIT FROM "VD1" (SC1) TO "D1"

AutoCAD SHX Text


AutoCAD SHX Text

25

AutoCAD SHX Text

(2) 3"

AutoCAD SHX Text

CONDUITS FROM "VD2" (IS) TO "VD3" (CR1)

AutoCAD SHX Text


AutoCAD SHX Text

26

AutoCAD SHX Text

2"

AutoCAD SHX Text

CONDUIT FROM "VD2" (IS) TO "D1"

AutoCAD SHX Text


AutoCAD SHX Text

27

AutoCAD SHX Text

2"

AutoCAD SHX Text

CONDUIT FROM "VD2" (IS) TO "VD1" (SC1)

AutoCAD SHX Text


AutoCAD SHX Text

28

AutoCAD SHX Text

(2) 3"

AutoCAD SHX Text

CONDUITS FROM "VD2" (IS) TO "VD3" (C-ROOM CUSTOMER LD INPUTS)

AutoCAD SHX Text


AutoCAD SHX Text

29

AutoCAD SHX Text

VARIES

AutoCAD SHX Text

CONDUIT(S) FROM "VD2" (IS) TO CUSTOMER SOURCES

AutoCAD SHX Text


AutoCAD SHX Text

30

AutoCAD SHX Text

4"

AutoCAD SHX Text

CONDUITS FROM "SC" TO "RC" UNDER FLOOR

AutoCAD SHX Text


AutoCAD SHX Text

31

AutoCAD SHX Text

6"

AutoCAD SHX Text

CONDUIT FROM "RC" TO "R1" UNDER FLOOR

AutoCAD SHX Text


AutoCAD SHX Text

32

AutoCAD SHX Text

3"

AutoCAD SHX Text

CONDUIT FROM "RC" TO "R1" UNDER FLOOR

AutoCAD SHX Text


AutoCAD SHX Text

33

AutoCAD SHX Text

3"

AutoCAD SHX Text

CONDUIT FROM "VD1" (SC1) TO "VD3" (IW2)

AutoCAD SHX Text


AutoCAD SHX Text

34

AutoCAD SHX Text

3/4"

AutoCAD SHX Text

CONDUIT FROM "VD3" TO "IC"

AutoCAD SHX Text


AutoCAD SHX Text

35

AutoCAD SHX Text

3/4"

AutoCAD SHX Text

CONDUIT FROM "VD3" TO "IC2"

AutoCAD SHX Text


AutoCAD SHX Text

36

AutoCAD SHX Text

3"

AutoCAD SHX Text

CONDUIT FROM "T1" TO "B10" UNDER FLOOR

AutoCAD SHX Text

37

AutoCAD SHX Text

3"

AutoCAD SHX Text

CONDUIT FROM "CRB" TO "B10" UNDER FLOOR (CUSTOMER PATIENT MONITORING)

AutoCAD SHX Text

38

AutoCAD SHX Text

1/2"

AutoCAD SHX Text

CONDUIT FROM "XF1" TO "SC1" ("T1") (OPTIONAL TABLE POWER OUTLET)

AutoCAD SHX Text


AutoCAD SHX Text

39

AutoCAD SHX Text

2 1/2"

AutoCAD SHX Text

CONDUIT FROM "T1" TO "IS2" (LDC) UNDER FLOOR

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

4 7

ARTIS PHENO

16055

E-102ATTENTION:

RE

FE

RE

NC

E D

OC

UM

EN

T - N

OT

F

OR

C

ON

ST

RU

CT

IO

N

ATTENTION:

RE

FE

RE

NC

E D

OC

UM

EN

T - N

OT

F

OR

C

ON

ST

RU

CT

IO

N

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

9'-1 1/16" - 10'-2"

AutoCAD SHX Text

9'-6"

AutoCAD SHX Text


AutoCAD SHX Text

AS NOTED

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

PROJECT #:

AutoCAD SHX Text

SHEET:

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text

REF. #:

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

SHEET OF

AutoCAD SHX Text

DATE:

AutoCAD SHX Text

SHEET OF

AutoCAD SHX Text

DRAWN BY:

AutoCAD SHX Text

DRAWN BY:

AutoCAD SHX Text

TYPICAL REV. 3

AutoCAD SHX Text

-ISSUE BLOCK-

AutoCAD SHX Text

DESCRIPTION

AutoCAD SHX Text

DATE

AutoCAD SHX Text

SYM

AutoCAD SHX Text

ARTIS PHENO

AutoCAD SHX Text

REV. 9

AutoCAD SHX Text

E-102

AutoCAD SHX Text

1

AutoCAD SHX Text

A-101

AutoCAD SHX Text

1

AutoCAD SHX Text

CONTROL ROOM

AutoCAD SHX Text

PROCEDURE ROOM

AutoCAD SHX Text

EQUIP. ROOM

AutoCAD SHX Text

30°

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

SC1

AutoCAD SHX Text

SC

AutoCAD SHX Text

CC

AutoCAD SHX Text

VD1

AutoCAD SHX Text

PU1

AutoCAD SHX Text

RC

AutoCAD SHX Text

VD2

AutoCAD SHX Text

IS

AutoCAD SHX Text

R1

AutoCAD SHX Text

IS2

AutoCAD SHX Text

CU2

AutoCAD SHX Text

CU1

AutoCAD SHX Text

IC2

AutoCAD SHX Text

B10

AutoCAD SHX Text

T1

AutoCAD SHX Text

IC

AutoCAD SHX Text

VD3

AutoCAD SHX Text

CRB

AutoCAD SHX Text

IW2

AutoCAD SHX Text

HD1

AutoCAD SHX Text

CR1

AutoCAD SHX Text

CU3

AutoCAD SHX Text

UPS

AutoCAD SHX Text

RMP

AutoCAD SHX Text

LOCATED IN COORDINATION WITH DISPLAY BOOM VENDOR

AutoCAD SHX Text

D1

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

ELECTRICAL DIMENSION PLAN

AutoCAD SHX Text

SCALE: 1/4" = 1'-0"

AutoCAD SHX Text

"R1" PENETRATION AREA

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text

NONE

AutoCAD SHX Text

ISOCENTER FLOOR STAND

AutoCAD SHX Text

"R1" PENETRATIONS ALLOWABLE IN ANY ORIENTATION/LOCATION WITHIN THE HATCHED AREA

AutoCAD SHX Text

FLOOR STAND MOUNTING PLATE

AutoCAD SHX Text

FLOOR COVER FRAME

AutoCAD SHX Text

1

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

5 7

ARTIS PHENO

16055

E-501ATTENTION:

RE

FE

RE

NC

E D

OC

UM

EN

T - N

OT

F

OR

C

ON

ST

RU

CT

IO

N

ATTENTION:

RE

FE

RE

NC

E D

OC

UM

EN

T - N

OT

F

OR

C

ON

ST

RU

CT

IO

N

AutoCAD SHX Text


AutoCAD SHX Text

AS NOTED

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

PROJECT #:

AutoCAD SHX Text

SHEET:

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text

REF. #:

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

SHEET OF

AutoCAD SHX Text

DATE:

AutoCAD SHX Text

SHEET OF

AutoCAD SHX Text

DRAWN BY:

AutoCAD SHX Text

DRAWN BY:

AutoCAD SHX Text

TYPICAL REV. 3

AutoCAD SHX Text

-ISSUE BLOCK-

AutoCAD SHX Text

DESCRIPTION

AutoCAD SHX Text

DATE

AutoCAD SHX Text

SYM

AutoCAD SHX Text

ARTIS PHENO

AutoCAD SHX Text

REV. 9

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

SIEMENS REMOTE SERVICE

AutoCAD SHX Text

TO ENSURE THE UPTIME OF YOUR SYSTEM DURING THE WARRANTY PERIOD (AND BEYOND WITH A SERVICE AGREEMENT), SIEMENS REMOTE SERVICES (SRS) REQUIRES REMOTE LOCAL AREA NETWORK ACCESS TO SIEMENS SYSTEMS.

AutoCAD SHX Text

THE PREFERRED CONNECTION METHOD IS (VPN) VIRTUAL PRIVATE NETWORK (WHERE THE CUSTOMER HAS AVAILABLE A VPN CAPABLE FIREWALL OR OTHER VPN APPLIANCE). THIS METHOD PROVIDES THE POSSIBILITY FOR REMOTE SYSTEM DIAGNOSTICS WITHOUT ADDITIONAL HARDWARE. PLEASE CONTACT SIEMENS REMOTE SERVICES (800-888-SIEM) TO DETERMINE IF THIS METHOD IS SUITABLE FOR YOUR SITE.

AutoCAD SHX Text

CUSTOMER VPN SERVER

AutoCAD SHX Text

CUSTOMER DMZ

AutoCAD SHX Text

IMAGING DEVICE SINGLE HOST IP OR IP SUBNET LIST

AutoCAD SHX Text

SIEMENS REMOTE SERVICES DMZ

AutoCAD SHX Text

PUBLIC INTERNET

AutoCAD SHX Text

FIREWALL

AutoCAD SHX Text

SRS ACCESS SERVER

AutoCAD SHX Text

CISCO 3745 ROUTER

AutoCAD SHX Text

EQUIPMENT GROUND CONDUCTOR TO COMPLY WITH THE FOLLOWING: 1) SIZED EQUIVALENT TO THE PHASE CONDUCTORS (FULL SIZED GROUND). 2) DERIVED FROM THE ELECTRICAL SERVICE, TRANSFORMER OR MAIN DISTRIBUTION PANEL FEEDING THE SIEMENS EQUIPMENT. 3) RUN IN THE SAME CONDUIT, TROUGH OR RACEWAY AS THE PHASE CONDUCTORS. 4) CONTINUOUS, WITH NO BREAKS OR USE OF CONDUIT, CHASSIS OR EARTH AS THE SOLE GROUNDING PATH. 5) BONDED TO CHASSIS AND/OR CONDUIT IN ACCORDANCE WITH THE NEC REQUIREMENTS. 6) MINIMIZE CONNECTIONS OR TERMINALS TO ENSURE CONTINUITY OVER THE LIFE OF THE INSTALLATION. 7) AS A NORM, THERE SHOULD NOT BE ANY CURRENT PRESENCE ON THE GROUND CONDUCTOR, BUT IT IS ACCEPTABLE TO HAVE <500mA DURING OPERATION OF THE <500mA DURING OPERATION OF THE 500mA DURING OPERATION OF THE DURING OPERATION OF THE IMAGING EQUIPMENT. 8) THERE MAY BE SOME APPLICATIONS WHICH REQUIRE AN ISOLATED GROUND AS PER NEC 250-96B.

AutoCAD SHX Text

GROUNDING NOTES

AutoCAD SHX Text

POOR POWER WILL ALTER EQUIPMENT PERFORMANCE

AutoCAD SHX Text

POWER QUALITY

AutoCAD SHX Text

IT IS IN THE CUSTOMER'S INTEREST THAT THE ELECTRICAL CONTRACTOR BE RESPONSIBLE FOR TESTING AND VERIFYING THAT THE EQUIPMENT POWER SUPPLY COMPLIES WITH THE SIEMENS SPECIFICATIONS.

AutoCAD SHX Text

NETWORK REQUIREMENT

AutoCAD SHX Text

A GIGABIT NETWORK IS REQUIRED FOR ADEQUATE IMAGE DATA TRANSFER SPEED BETWEEN THE IMAGER AND 3D RECONSTRUCTION WORKSTATION. WORKFLOW AND CLINICAL NEEDS DEMAND 3D IMAGES BE AVAILABLE FOR REVIEW BY CLINICAL STAFF IMMEDIATELY UPON ACQUISITION.

AutoCAD SHX Text

LIGHTING POWER FROM WALL SWITCH 100-277 VAC

AutoCAD SHX Text

WARNING LIGHT/ROOM LIGHT SCHEMATIC

AutoCAD SHX Text

LIGHTING DETAIL

AutoCAD SHX Text

NONE

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text

SIEMENS SYSTEM CABINET "SC1"

AutoCAD SHX Text

NEUTRAL

AutoCAD SHX Text

HOSPITAL POWER 100-277 VAC

AutoCAD SHX Text

WARNING LIGHT POWER 100-277 VAC

AutoCAD SHX Text

NEUTRAL

AutoCAD SHX Text

"X-RAY ON" WARNING LIGHT

AutoCAD SHX Text

ROOM LIGHTS CONTROL RELAY

AutoCAD SHX Text

X-RAY ON WARNING LIGHT CONTROL RELAY

AutoCAD SHX Text

24 VDC RELAYS MUST INCLUDE A FREE-WHEELING DIODE (P/N 1N4002 OR EQUIVALENT). ALL ITEMS PROVIDED BY CUSTOMER ELECTRICAL CONTRACTOR EXCEPT CONTACTS INSIDE SIEMENS "SC1" CABINET (ITEMS INSIDE DOTTED LINES). ALL WIRING THAT CONNECTS TO SIEMENS "SC1" CABINET MUST BE 14-18 AWG STRANDED WIRE. 4 WIRES LABELED "24 VDC", "ROOM LIGHTS" AND "X-RAY ON" SHOULD BE SENT TO SIEMENS "SC1" CABINET. 24 VDC RELAYS ARE TO BE SELECTED BY ELECTRICAL CONTRACTOR TO HANDLE THE VOLTAGE AND AMPERAGE OF LIGHTING CURCUIT. IF NEEDED, A SWITCH TO BLOCK RADIATION CAN BE INSTALLED IN SERIES WITH THE DOOR CONTACT. * THE SWITCH (24 VDC / 20 MA) MUST BE PROVIDED ON SITE. * CONTROL USING +24 V FROM THE SYSTEM CONTROL CABINET * PLAN THE SWITCH SO THAT UNINTENTIONAL OPERATION IS NOT POSSIBLE. * THE SWITCH MUST BE PROVIDED WITH AN APPROPRIATE SYMBOL (OR DESIGNATION) FROM WHICH THE FUNCTION CAN BE RECOGNIZED..

AutoCAD SHX Text

N.C.

AutoCAD SHX Text

N.O.

AutoCAD SHX Text

ROOM LIGHTS

AutoCAD SHX Text

24 VDC RELAY

AutoCAD SHX Text

24 VDC RELAY

AutoCAD SHX Text

2.

AutoCAD SHX Text

3.

AutoCAD SHX Text

4.

AutoCAD SHX Text

5.

AutoCAD SHX Text

6.

AutoCAD SHX Text

24 VDC POWER SUPPLY

AutoCAD SHX Text

1.

AutoCAD SHX Text

NOTES:

AutoCAD SHX Text

1

AutoCAD SHX Text

MAXIMUM CABLE LENGTHS (TYPICAL EQUIPMENT)

AutoCAD SHX Text

62'

AutoCAD SHX Text

CU1

AutoCAD SHX Text

PU1

AutoCAD SHX Text

SC1

AutoCAD SHX Text

16'

AutoCAD SHX Text

T1

AutoCAD SHX Text

CR1

AutoCAD SHX Text

IS

AutoCAD SHX Text

62'

AutoCAD SHX Text

45'

AutoCAD SHX Text

59'

AutoCAD SHX Text

26'/62'

AutoCAD SHX Text

62'

AutoCAD SHX Text

CC

AutoCAD SHX Text

EQUIPMENT ROOM

AutoCAD SHX Text

PROCEDURE ROOM

AutoCAD SHX Text

CONTROL ROOM

AutoCAD SHX Text

R1

AutoCAD SHX Text

D1

AutoCAD SHX Text

RC

AutoCAD SHX Text

44'

AutoCAD SHX Text

32'

AutoCAD SHX Text

52'

AutoCAD SHX Text

52'

AutoCAD SHX Text

91'

AutoCAD SHX Text

CU2

AutoCAD SHX Text

32'

AutoCAD SHX Text

52'

AutoCAD SHX Text

IW2

AutoCAD SHX Text

62'

AutoCAD SHX Text

6'

AutoCAD SHX Text

98'

AutoCAD SHX Text

TABLE POWER OUTLET SAFETY

AutoCAD SHX Text

NOTE: LIFE-SUSTAINING EQUIPMENT MUST NOT BE CONNECTED TO THE TABLE POWER OUTLET (IF INSTALLED) IN THE SIEMENS PATIENT TABLE. POWER WILL BE DISCONNECTED IF EPO BUTTON IS PRESSED. TABLE OUTLET IS 120V, FUSED AT 5A.

AutoCAD SHX Text

WIRING SYSTEM:

AutoCAD SHX Text

162 KVA

AutoCAD SHX Text

480Y/277V, 3 PHASE, 5-WIRE, 60 HZ.

AutoCAD SHX Text

8 KVA

AutoCAD SHX Text

2%%%

AutoCAD SHX Text

%%P10% OF SYSTEM VOLTAGE

AutoCAD SHX Text

%%P 1 HZ

AutoCAD SHX Text

POWER QUALITY PARAMETERS

AutoCAD SHX Text

LINE IMPEDANCE

AutoCAD SHX Text

120 (mΩ)120 (mΩ)

AutoCAD SHX Text

2. SIEMENS HEALTHCARE REQUIRES THAT THE INCOMING POWER MEETS THE POWER QUALITY REQUIREMENTS.

AutoCAD SHX Text

MINIMUM POWER SUPPLY: IF AN ON-SITE TRANSFORMER IS REQUIRED TO OBTAIN OPERATING VOLTAGE, IT MUST BE OF SUFFICIENT CAPACITY AND CHARACTERISTICS TO MAINTAIN SUPPLY VOLTAGE AND IMPEDANCE REQUIREMENTS (TRANSFORMER AND CONDUCTORS).

AutoCAD SHX Text

POWER SUPPLY NOTES: 1. INCOMING POWER SUPPLIES FOR SIEMENS EQUIPMENT SHOULD BE DEDICATED (BACK TO SOURCE), ISOLATED AND INSULATED FROM ANY OTHER EQUIPMENT SUCH AS ELEVATORS, GENERATORS, HVAC SYSTEMS, ETC.

AutoCAD SHX Text

X-RAY GENERATOR (PU1) MOMENTARY RATING: (RADIOGRAPHIC EXPOSURE)

AutoCAD SHX Text

X-RAY GENERATOR (PU1) LONG-TIME RATING: (FLUOROSCOPY)

AutoCAD SHX Text

MAXIMUM LINE VOLTAGE VARIATION

AutoCAD SHX Text

PHASE IMBALANCE:

AutoCAD SHX Text

FREQUENCY VARIATION:

AutoCAD SHX Text

SYSTEM CABINET (SC1) LONG-TIME RATING:

AutoCAD SHX Text

17.2 KVA

AutoCAD SHX Text

POWER REQUIREMENTS

AutoCAD SHX Text

IMAGE SYSTEM IN EQUIPMENT ROOM

AutoCAD SHX Text

SYSTEM CONNECTIONS

AutoCAD SHX Text

NONE

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text

CONTROL ROOM

AutoCAD SHX Text

IW2

AutoCAD SHX Text

IMAGE SYSTEM

AutoCAD SHX Text

IS

AutoCAD SHX Text

62'

AutoCAD SHX Text

9'-6"

AutoCAD SHX Text

9'-6"

AutoCAD SHX Text

9'-6"

AutoCAD SHX Text

9'-6"

AutoCAD SHX Text

16'

AutoCAD SHX Text

%%USTANDARD:

AutoCAD SHX Text

LIVE DISPLAY

AutoCAD SHX Text

MONITOR

AutoCAD SHX Text

%%UOPTIONS:

AutoCAD SHX Text

REFERENCE DISPLAY

AutoCAD SHX Text

HAND SWITCH

AutoCAD SHX Text

CONTROL MODULES

AutoCAD SHX Text

EMERGENCY STOP

AutoCAD SHX Text

FOOT SWITCH

AutoCAD SHX Text

6'-6"

AutoCAD SHX Text

62'

AutoCAD SHX Text

CPC (CENTRAL POWER UNIT)

AutoCAD SHX Text

CR1

AutoCAD SHX Text

9'-6"

AutoCAD SHX Text

62'

AutoCAD SHX Text

6'

AutoCAD SHX Text

2

AutoCAD SHX Text

POWER SCHEDULE

AutoCAD SHX Text

ITEM

AutoCAD SHX Text

QTY

AutoCAD SHX Text

DESCRIPTION

AutoCAD SHX Text

EPO

AutoCAD SHX Text

VARIES

AutoCAD SHX Text

MP

AutoCAD SHX Text

1

AutoCAD SHX Text

MAIN BREAKER AMPS: 125

AutoCAD SHX Text

A

AutoCAD SHX Text

1

AutoCAD SHX Text

BREAKER AMPS: 100 (FOR PU1)

AutoCAD SHX Text

B

AutoCAD SHX Text

1

AutoCAD SHX Text

BREAKER AMPS: 30 (FOR SC1)

AutoCAD SHX Text

1) ALL WIRES MUST BE SAME SIZE.

AutoCAD SHX Text

VOLTS

AutoCAD SHX Text

480/277Y

AutoCAD SHX Text

3

AutoCAD SHX Text

PHASES

AutoCAD SHX Text

NEUTRAL

AutoCAD SHX Text

GROUND

AutoCAD SHX Text

TOTAL WIRES

AutoCAD SHX Text

1

AutoCAD SHX Text

1

AutoCAD SHX Text

5 (NOTE 1)

AutoCAD SHX Text

VOLTS

AutoCAD SHX Text

480Y

AutoCAD SHX Text

3

AutoCAD SHX Text

PHASES

AutoCAD SHX Text

NEUTRAL

AutoCAD SHX Text

GROUND

AutoCAD SHX Text

TOTAL WIRES

AutoCAD SHX Text

0

AutoCAD SHX Text

1

AutoCAD SHX Text

4 (NOTE 1)

AutoCAD SHX Text

VOLTS

AutoCAD SHX Text

480/277Y

AutoCAD SHX Text

3

AutoCAD SHX Text

PHASES

AutoCAD SHX Text

NEUTRAL

AutoCAD SHX Text

GROUND

AutoCAD SHX Text

TOTAL WIRES

AutoCAD SHX Text

1

AutoCAD SHX Text

1

AutoCAD SHX Text

5 (NOTE 1)

AutoCAD SHX Text

ALL ITEMS LISTED IN THIS SCHEDULE SHALL BE SUPPLIED AND INSTALLED BY CUSTOMER/CONTRACTOR.

AutoCAD SHX Text

D

AutoCAD SHX Text

1

AutoCAD SHX Text

EPO

AutoCAD SHX Text

MP

AutoCAD SHX Text

ALL CONDUITS AND WIRES SIZES MUST BE DETERMINED BY THE ELECTRICAL ENGINEER OF RECORD PER N.E.C AND TO MAINTAIN SIEMENS IMPEDANCE REQUIREMENTS.

AutoCAD SHX Text

REFER TO EATON INFORMATION FOR UPS INPUT/OUTPUT WIRE SIZE REQUIREMENTS. OBTAIN EATON PLANNING GUIDE FROM SIEMENS PROJECT MANAGER.

AutoCAD SHX Text

POLYDOROS A100 CABINET

AutoCAD SHX Text

MAXIMUM WIRE SIZE FOR TERMINAL LUGS IS #3/0 AWG "PU1" CABINET.

AutoCAD SHX Text

NC

AutoCAD SHX Text

NC

AutoCAD SHX Text

NC

AutoCAD SHX Text

MAIN BREAKER EPO CIRCUIT POWER SOURCE

AutoCAD SHX Text

NOTE #2

AutoCAD SHX Text

A (100A) (100A)

AutoCAD SHX Text

B (30A) (30A)

AutoCAD SHX Text

PROVIDE ADDITIONAL EPO NEAR UPS IF UPS IS LOCATED REMOTELY FROM SIEMENS EQUIPMENT ROOM.

AutoCAD SHX Text

EPO

AutoCAD SHX Text

EPO

AutoCAD SHX Text

NOTE #1

AutoCAD SHX Text

NOTE 1 - EPO CIRCUIT #1 MAIN CIRCUIT BREAKER EMERGENCY POWER OFF BUTTON WITH PROTECTIVE COVER THAT PREVENTS ACCIDENTAL ACTIVATION. THE EPO MUST BE OF FAIL-SAFE DESIGN. ALL EPO'S TO HAVE MECHANICAL LATCHING MECHANISM. MECHANICAL LATCHING MECHANISM. . EPO MUST BE RESET BEFORE MAIN BREAKER CAN RESUME OPERATION. CONTACTS AND WIRING CONFIGURATION TO BE DESIGNED BY ELECTRICAL ENGINEER OF RECORD. NOTE 2 - EPO CIRCUIT #2 EPO CONTACTS TO BE NORMALLY CLOSED, WIRED IN NORMALLY CLOSED, WIRED IN , WIRED IN SERIES, CONNECTED TO 9355 UPS ONLY. THE EPOs MUST BE INSTALLED BY A QUALIFIED ELECTRICAL CONTRACTOR ACCORDING TO NATIONAL ELECTRICAL CODE, STATE AND LOCAL REGULATIONS. MEASURES SHOULD BE TAKEN TO DESIGN THE CIRCUIT IN SUCH A WAY THAT IT WILL ALWAYS WORK WHEN THE MEDICAL EQUIPMENT IS POWERED. THE CUSTOMER IS SOLELY RESPONSIBLE FOR THE IMPLEMENTATION OF THE EPOs AND THEIR ASSOCIATED CIRCUITS AND MUST MAKE THE FINAL DETERMINATION CONSIDERING ALL SITE CONDITIONS AND REGULATORY FACTORS.

AutoCAD SHX Text

UPS

AutoCAD SHX Text

SYSTEM CABINET

AutoCAD SHX Text

3#4 AWG

AutoCAD SHX Text

ONLY REQUIRED IF THE SUPPLIED UPS WIRING HARNESS IS TOO SHORT FOR CONNECTION TO OUTPUT XFMR CABINET.

AutoCAD SHX Text

D

AutoCAD SHX Text

9355 15KVA UPS/BATT/ INPUT XFMR CABINET

AutoCAD SHX Text

REMOTE MONITOR PANEL

AutoCAD SHX Text

RMP

AutoCAD SHX Text

6#16-24 AWG

AutoCAD SHX Text

(MAX. 500')

AutoCAD SHX Text

C (15A) (15A)

AutoCAD SHX Text

XF1

AutoCAD SHX Text

SIEMENS-SUPPLIED POWER CABLE FOR TABLE OUTLET. E.C. TO CONNECT TO TRANSFORMER.

AutoCAD SHX Text

C

AutoCAD SHX Text

1

AutoCAD SHX Text

BREAKER AMPS: 15 (FOR STEP-DOWN XFMR "XF1")

AutoCAD SHX Text

VOLTS

AutoCAD SHX Text

480

AutoCAD SHX Text

1 (L1,L2)

AutoCAD SHX Text

PHASES

AutoCAD SHX Text

NEUTRAL

AutoCAD SHX Text

GROUND

AutoCAD SHX Text

TOTAL WIRES

AutoCAD SHX Text

0

AutoCAD SHX Text

1

AutoCAD SHX Text

3

AutoCAD SHX Text

OPTIONAL TABLE OUTLET POWER FEED. CONTACT SIEMENS PROJECT MANAGER.

AutoCAD SHX Text

XF1

AutoCAD SHX Text

1

AutoCAD SHX Text

M (125A) (125A)

AutoCAD SHX Text

SC1

AutoCAD SHX Text

PU1

AutoCAD SHX Text

M

AutoCAD SHX Text

1

AutoCAD SHX Text

MAIN PANEL WITH CIRCUIT BREAKERS FLUSH OR SURFACE MOUNTED.

AutoCAD SHX Text

MAIN BREAKER MUST HAVE TRIPPING DEVICE SO WHEN ANY EPO IS PRESSED, THE MAIN BREAKER TRIPS.

AutoCAD SHX Text

NOTE: UNLESS OTHERWISE NOTED, ALL BREAKERS WILL BE 80% RATED

AutoCAD SHX Text

1.5kVA, 480V PRIMARY, 120V GROUNDED SECONDARY STEP-DOWN SINGLE-PHASE TRANSFORMER WITH PRIMARY AND SECONDARY FUSE PROTECTION FOR TABLE OUTLET POWER, CONNECTED TO AN ADJACENT FLUSH WALL-MOUNTED 15A, 125VAC UL 943 GFCI WITH BLANK FACE (NO CONTACT OPENINGS OR NEMA CONFIGURATION) WITH LED INDICATION, PUSH-TO-TEST AND PUSH-TO-RESET BUTTONS, AND A CLEAR LEXAN HINGED COVER TO AVOID INADVERTENT MANUAL TRIP.

AutoCAD SHX Text

3-PHASE (PLUS N,G) 30A, 600V HD FUSIBLE SERVICE DISCONNECT LOCATED AT EYE-LEVEL, WITHIN 10' OF SIEMENS SYSTEM CABINET (SC1) AND 30A RK5 FUSES.

AutoCAD SHX Text

9355 UPS OUTPUT XFMR CABINET

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

6 7

AutoCAD SHX Text

CONTRACTOR SUPPLIED CABLES

AutoCAD SHX Text

FROM

AutoCAD SHX Text

VIA

AutoCAD SHX Text

TO

AutoCAD SHX Text

DESCRIPTION

AutoCAD SHX Text

REMARKS

AutoCAD SHX Text

PANEL

AutoCAD SHX Text

1

AutoCAD SHX Text

MP

AutoCAD SHX Text

ELECTRICAL CONTRACTOR TO SIZE PLUS GROUND

AutoCAD SHX Text


AutoCAD SHX Text

MP

AutoCAD SHX Text

2

AutoCAD SHX Text

PU1

AutoCAD SHX Text

3#2, 1#2 GROUND AND CONNECT

AutoCAD SHX Text


AutoCAD SHX Text

MP

AutoCAD SHX Text

3

AutoCAD SHX Text

UPS

AutoCAD SHX Text

ELECTRICAL CONTRACTOR TO SIZE

AutoCAD SHX Text


AutoCAD SHX Text

UPS

AutoCAD SHX Text

4

AutoCAD SHX Text

SD

AutoCAD SHX Text

ELECTRICAL CONTRACTOR TO SIZE PLUS GROUND

AutoCAD SHX Text


AutoCAD SHX Text

SD

AutoCAD SHX Text

5

AutoCAD SHX Text

SC1

AutoCAD SHX Text

ELECTRICAL CONTRACTOR TO SIZE PLUS GROUND (MAX #6 AWG)

AutoCAD SHX Text


AutoCAD SHX Text

UPS

AutoCAD SHX Text

6

AutoCAD SHX Text

EPO

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

RMP

AutoCAD SHX Text

7

AutoCAD SHX Text

UPS

AutoCAD SHX Text

6#16-24 UP TO 500'

AutoCAD SHX Text


AutoCAD SHX Text

MP

AutoCAD SHX Text

8

AutoCAD SHX Text

EPO

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

EPO

AutoCAD SHX Text

9

AutoCAD SHX Text

EPO

AutoCAD SHX Text

4#12, PLUS GROUND

AutoCAD SHX Text

EMERGENCY POWER

AutoCAD SHX Text

SC1

AutoCAD SHX Text

10

AutoCAD SHX Text

WL

AutoCAD SHX Text

14-18 AWG

AutoCAD SHX Text

SEE "LIGHTING DETAIL" SHEET E-501

AutoCAD SHX Text

SC1

AutoCAD SHX Text

11

AutoCAD SHX Text

DS

AutoCAD SHX Text

3#12, PLUS GROUND

AutoCAD SHX Text

DOOR SWITCH

AutoCAD SHX Text

MP

AutoCAD SHX Text

12

AutoCAD SHX Text

XF1

AutoCAD SHX Text

EC TO SIZE (OPTIONAL TABLE POWER OUTLET)

AutoCAD SHX Text


AutoCAD SHX Text

SIEMENS SUPPLIED CABLES

AutoCAD SHX Text

FROM

AutoCAD SHX Text

VIA

AutoCAD SHX Text

TO

AutoCAD SHX Text

DESCRIPTION

AutoCAD SHX Text

REMARKS

AutoCAD SHX Text

R1

AutoCAD SHX Text

13, SC

AutoCAD SHX Text

PU1

AutoCAD SHX Text

MAXIMUM LENGTH 52'

AutoCAD SHX Text

R1

AutoCAD SHX Text

14, SC

AutoCAD SHX Text

PU1

AutoCAD SHX Text

(2) HIGH VOLTAGE CABLES

AutoCAD SHX Text

MAXIMUM LENGTH 52'

AutoCAD SHX Text

R1

AutoCAD SHX Text

15, SC

AutoCAD SHX Text

SC1

AutoCAD SHX Text

MAXIMUM LENGTH 52'

AutoCAD SHX Text

R1

AutoCAD SHX Text

16, CU3

AutoCAD SHX Text

CU1

AutoCAD SHX Text

LIQUID COOLING HOSES

AutoCAD SHX Text

MAXIMUM LENGTH 91'

AutoCAD SHX Text

R1

AutoCAD SHX Text

17, CU3

AutoCAD SHX Text

CU2

AutoCAD SHX Text

LIQUID COOLING HOSES

AutoCAD SHX Text

MAXIMUM LENGTH 52'

AutoCAD SHX Text

SC1

AutoCAD SHX Text

18, VD1, VD3, HD1

AutoCAD SHX Text

CR1

AutoCAD SHX Text

FOR CONTROL ROOM OPTIONS (CONTROL MODULES, FOOT SWITCH, DISPLAY, ECC)

AutoCAD SHX Text

MAXIMUM LENGTH 62'

AutoCAD SHX Text

SC1

AutoCAD SHX Text

19, SC

AutoCAD SHX Text

T1

AutoCAD SHX Text

MAXIMUM LENGTH 45'

AutoCAD SHX Text

SC1

AutoCAD SHX Text

20, VD1

AutoCAD SHX Text

CU1

AutoCAD SHX Text

MAXIMUM LENGTH 98'

AutoCAD SHX Text

SC1

AutoCAD SHX Text

21, SC2

AutoCAD SHX Text

CU3

AutoCAD SHX Text

MAXIMUM LENGTH 32'

AutoCAD SHX Text

SC1

AutoCAD SHX Text

22, VD1, VD2

AutoCAD SHX Text

IS

AutoCAD SHX Text

MAXIMUM LENGTH 26'

AutoCAD SHX Text

SC1

AutoCAD SHX Text

23, VD1

AutoCAD SHX Text

D1

AutoCAD SHX Text

MAXIMUM LENGTH 62'

AutoCAD SHX Text

SC1

AutoCAD SHX Text

24, VD1

AutoCAD SHX Text

D1

AutoCAD SHX Text

RADIATION ON LIGHT

AutoCAD SHX Text

MAXIMUM LENGTH 98'

AutoCAD SHX Text

IS

AutoCAD SHX Text

25, VD2, VD3

AutoCAD SHX Text

CR1

AutoCAD SHX Text

MAXIMUM LENGTH 59'

AutoCAD SHX Text

IS

AutoCAD SHX Text

26, VD2

AutoCAD SHX Text

D1

AutoCAD SHX Text

DCS LARGE DISPLAY (STANDARD CABLE)

AutoCAD SHX Text

MAXIMUM LENGTH 82'

AutoCAD SHX Text

IS

AutoCAD SHX Text

27, VD2, VD1

AutoCAD SHX Text

SC1

AutoCAD SHX Text

DCS LARGE DISPLAY (STANDARD CABLE)

AutoCAD SHX Text

MAXIMUM LENGTH 57'

AutoCAD SHX Text

IS

AutoCAD SHX Text

28, VD2

AutoCAD SHX Text

VD3

AutoCAD SHX Text

CUSTOMER LD INPUTS IN CONTROL ROOM

AutoCAD SHX Text

MAXIMUM LENGTH 118'

AutoCAD SHX Text

IS

AutoCAD SHX Text

29, VD2

AutoCAD SHX Text

CUSTOMER SOURCES

AutoCAD SHX Text

CUSTOMER LD INPUTS IN PROCEDURE ROOM

AutoCAD SHX Text

MAXIMUM LENGTH 118'

AutoCAD SHX Text

SC1

AutoCAD SHX Text

30, SC

AutoCAD SHX Text

RC

AutoCAD SHX Text

MAXIMUM LENGTH 32'

AutoCAD SHX Text

RC

AutoCAD SHX Text

31

AutoCAD SHX Text

R1

AutoCAD SHX Text

MAXIMUM LENGTH 44'

AutoCAD SHX Text

RC

AutoCAD SHX Text

32

AutoCAD SHX Text

R1

AutoCAD SHX Text

MAXIMUM LENGTH 44'

AutoCAD SHX Text

SC1

AutoCAD SHX Text

33, VD1,VD3,HD1

AutoCAD SHX Text

IW2

AutoCAD SHX Text

2ND OPERATION / INJECTOR CONNECTION (CONTROL ROOM)

AutoCAD SHX Text

MAXIMUM LENGTH 62'

AutoCAD SHX Text

VD3

AutoCAD SHX Text

34

AutoCAD SHX Text

IC

AutoCAD SHX Text

INTERCOM PROCEDURE ROOM MICROPHONE

AutoCAD SHX Text

MAXIMUM LENGTH 82'

AutoCAD SHX Text

VD3

AutoCAD SHX Text

35

AutoCAD SHX Text

IC2

AutoCAD SHX Text

INTERCOM PROCEDURE ROOM LOUDSPEAKER

AutoCAD SHX Text

MAXIMUM LENGTH 82'

AutoCAD SHX Text

T1

AutoCAD SHX Text

36

AutoCAD SHX Text

B10

AutoCAD SHX Text

CRB

AutoCAD SHX Text

37

AutoCAD SHX Text

B10

AutoCAD SHX Text

CUSTOMER PATIENT MONITORING, ETC.

AutoCAD SHX Text

XF1

AutoCAD SHX Text

38, SC1, CONDUIT 18

AutoCAD SHX Text

T1

AutoCAD SHX Text

OPTIONAL TABLE POWER OUTLET

AutoCAD SHX Text

MAXIMUM LENGTH 91'

AutoCAD SHX Text

T1

AutoCAD SHX Text

39, IS2

AutoCAD SHX Text

LDC

AutoCAD SHX Text

VGA LD INPUT TO TABLE

AutoCAD SHX Text

MAXIMUM LENGTH 118'

ARTIS PHENO

16055

M-501ATTENTION:

RE

FE

RE

NC

E D

OC

UM

EN

T - N

OT

F

OR

C

ON

ST

RU

CT

IO

N

ATTENTION:

RE

FE

RE

NC

E D

OC

UM

EN

T - N

OT

F

OR

C

ON

ST

RU

CT

IO

N

ATTENTION:

RE

FE

RE

NC

E D

OC

UM

EN

T - N

OT

F

OR

C

ON

ST

RU

CT

IO

N

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

9'-1 1/16" - 10'-2"

AutoCAD SHX Text

9'-6"

AutoCAD SHX Text


AutoCAD SHX Text

AS NOTED

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

PROJECT #:

AutoCAD SHX Text

SHEET:

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text

REF. #:

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

SHEET OF

AutoCAD SHX Text

DATE:

AutoCAD SHX Text

SHEET OF

AutoCAD SHX Text

DRAWN BY:

AutoCAD SHX Text

DRAWN BY:

AutoCAD SHX Text

TYPICAL REV. 3

AutoCAD SHX Text

-ISSUE BLOCK-

AutoCAD SHX Text

DESCRIPTION

AutoCAD SHX Text

DATE

AutoCAD SHX Text

SYM

AutoCAD SHX Text

ARTIS PHENO

AutoCAD SHX Text

REV. 9

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

HEAT LOADS

AutoCAD SHX Text

FOR BTU'S OF SEIMENS EQUIPMENT, REFER TO THE EQUIPMENT LEGEND, SHEET A-101.

AutoCAD SHX Text

AXIS IMAGE SYSTEM

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text

3/4"=1'-0"

AutoCAD SHX Text

*1

AutoCAD SHX Text

*1 CABLE ROUTING VIA A FLOOR OR WALL OUTLET IS POSSIBLE ACROSS THE ENTIRE WIDTH OF THE IMAGE SYSTEM.

AutoCAD SHX Text

FRONT VIEW

AutoCAD SHX Text

SIDE VIEW

AutoCAD SHX Text

TOP-DOWN VIEW

AutoCAD SHX Text

CASTORS

AutoCAD SHX Text

EXHAUST AIR

AutoCAD SHX Text

IS

AutoCAD SHX Text

AIR INTAKE

AutoCAD SHX Text

CABLE LOOP APPROX. 6 FT. ON THE FLOOR UNDER THE IMAGE SYSTEM FOR SERVICE

AutoCAD SHX Text

AIR INTAKE

AutoCAD SHX Text

EXHAUST AIR

AutoCAD SHX Text

EXHAUST AIR

AutoCAD SHX Text

EXHAUST AIR

AutoCAD SHX Text

1

AutoCAD SHX Text

41°F-86°F (RECOMMENDED TEMPERATURE 70°F) FROST FREE 559 CFM 59 dB(A)

AutoCAD SHX Text

59°F-86°F (RECOMMENDED TEMPERATURE 72°F)

AutoCAD SHX Text

59°F-86°F (RECOMMENDED TEMPERATURE 72°F) 20%-75% NON CONDENSING 9° F/HR 94 CFM 55 dB(A)

AutoCAD SHX Text

59°F-95°F (RECOMMENDED TEMPERATURE 72°F) 20%-75% NON CONDENSING 18° F/HR 371 CFM 53 dB(A)

AutoCAD SHX Text


AutoCAD SHX Text

ENVIRONMENTAL CONDITIONS

AutoCAD SHX Text

TEMPERATURE RANGE: RELATIVE HUMIDITY: AIR FLOW VOLUME: MAX. NOISE GENERATION:

AutoCAD SHX Text

TUBE COOLING UNIT (CU1)

AutoCAD SHX Text

SYSTEM CONTROL CABINET (SC1)

AutoCAD SHX Text

POLYDOROS GENERATOR (PU1)

AutoCAD SHX Text

TEMPERATURE RANGE:

AutoCAD SHX Text

TEMPERATURE RANGE: RELATIVE HUMIDITY: MAX. TEMP. GRADIENT: AIR FLOW VOLUME: MAX. NOISE GENERATION:

AutoCAD SHX Text

EXAMINATION AND CONTROL ROOM

AutoCAD SHX Text

AXIS IMAGE SYSTEM (IS)

AutoCAD SHX Text

TEMPERATURE RANGE:

AutoCAD SHX Text

TEMPERATURE RANGE: RELATIVE HUMIDITY: MAX. TEMP. GRADIENT: AIR FLOW VOLUME: MAX. NOISE GENERATION:

AutoCAD SHX Text

RELATIVE HUMIDITY:

AutoCAD SHX Text

20% - 75% NON-CONDENSING

AutoCAD SHX Text

RELATIVE HUMIDITY:

AutoCAD SHX Text

20%-75% NON-CONDENSING

AutoCAD SHX Text

MAX. TEMP. GRADIENT:

AutoCAD SHX Text

9° F/HR

AutoCAD SHX Text

AIR FLOW VOLUME:

AutoCAD SHX Text

300 CFM

AutoCAD SHX Text

MAX. NOISE GENERATION:

AutoCAD SHX Text

55 dB(A)

AutoCAD SHX Text

FLOOR STAND ROBOTIC CABINET (RC)

AutoCAD SHX Text


AutoCAD SHX Text

TEMPERATURE RANGE:

AutoCAD SHX Text


AutoCAD SHX Text

67 dB(A)

AutoCAD SHX Text

MAXIMUM TEMPERATURE GRADIENT: ATMOSPHERIC PRESSURE: SHOCKS: VIBRATIONS: MAX. NOISE GENERATION:

AutoCAD SHX Text

FLOOR STAND WITH FLAT DETECTOR (R1)

AutoCAD SHX Text

9° F/HR 700hPa - 1040hPa MAXIMUM 10G/16MS MAXIMUM 0.1 G/10-200HZ <55 dB(A)

AutoCAD SHX Text


AutoCAD SHX Text

FD COOLING UNIT (CU2)

AutoCAD SHX Text

TEMPERATURE RANGE:

AutoCAD SHX Text

RELATIVE HUMIDITY:

AutoCAD SHX Text

20% - 75% NON-CONDENSING

AutoCAD SHX Text


AutoCAD SHX Text

48 dB(A)

AutoCAD SHX Text

TUBE COOLING UNIT

AutoCAD SHX Text

SCALE: 1"=1'-0"

AutoCAD SHX Text

TOP

AutoCAD SHX Text

RIGHT SIDE

AutoCAD SHX Text

FRONT

AutoCAD SHX Text

AIR INTAKE

AutoCAD SHX Text

AIR EXHAUST

AutoCAD SHX Text

*1 FOR AIR INTAKE/EXHAUST

AutoCAD SHX Text

*2 FOR COOLING HOSES

AutoCAD SHX Text

*3 COOLING WATER FILLER TUBE

AutoCAD SHX Text

*1

AutoCAD SHX Text

*1

AutoCAD SHX Text

*2

AutoCAD SHX Text

*3

AutoCAD SHX Text

*3

AutoCAD SHX Text

MIN.

AutoCAD SHX Text

NOTE: THIS UNIT IS A SELF-CONTAINED, CLOSED LOOP, TAP WATER-FILLED SYSTEM SERVICED BY SIEMENS. NO OUTSIDE CHILLED WATER SUPPLY IS REQUIRED. PROVIDE 2.5 GALLON SPILLAGE PROTECTION AS REQUIRED. MAXIMUM ADMISSIBLE HEIGHT DIFFERENCE BETWEEN COOLER AND THE X-RAY TUBE IS +/- 32 FT. PROVIDE HOSE HOLDER FOR EXCESS COOLING HOSE STORAGE.

AutoCAD SHX Text

2

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

7 7

TYPICAL DRAWING / ARTIS PHENO - Siemens Healthineers Pheno//16055.pdf · artis pheno 16055a-101...

Documents

Transcript of TYPICAL DRAWING / ARTIS PHENO - Siemens Healthineers Pheno//16055.pdf · artis pheno 16055a-101...