Type P70SE - Fuchs · PDF file11. Survey and List of Parameters 11.1 Explanation of Parameter...

QUICK-ROTAN Elektromotoren GmbHKönigstraße 15467655 KaiserslauternTel: 0631 / 200 38 80Fax: 0631 / 200 38 62E-Mail: [email protected]: www.quick-rotan.com

English 2004-11-10

P70SEInstruction Manual

Part 3

Type

QE5542

Contents Page

Part 3

11. Survey and List of Parameters 11.1 - 11.10

11.1 Explanation of Parameter Survey

11.2 Explanation of Parameter List

11.3 Parameter Survey

11.4 List of Parameters

12. Electrical Connections Diagram 12.1 - 12.8

13. Maintenance and Repair 13.1

p-70-se-3-en 04-11-10

Technical updatings reserved!

11. Survey and List of Parameters

11.1 Explanation of Parameter Survey

The parameter survey is designed as an aid for finding parameters quickly. It is a summary of referencesfor the parameter list. Listed behind each reference are all parameters which exert an influence on thefunction described by the reference.

The parameter survey is divided into five columns:Column 1 shows the references (functions) to which parameters are assigned.Column 2 shows the abbreviations of the respective functions.Column 3 shows all parameters (setting numbers) belonging to the respective reference.Column 4 shows, for each function (reference) which controls inputs or outputs, the applicableindications such as Ex or Ax which can also be found on the connections diagram.Column 5 shows, for each function (control inputs (Ex) or control outputs (Ax)), the respectiveplugs with the number of contacts (see connections diagram).

Example for searching a parameter:Keyword (function): inverse rotationThe parameter survey shows in column 3 the parameter numbers 618, 623, 801.

Suppose that the inverse rotation function is to be enabled. The parameter list shows this function underparameter number 618.

11.2 Explanation of Parameter List

The parameter list is divided into 5 columns. These comprise, incolumn 1: the parameter number,column 2: is the explanation (meaning) of the parameters and the coding system of row 1 of the keys

of the mini operator's panel, used when the parameter concerned can be programmed withthe mini operator's panel,

column 3: the programming level (A, B, C) on which the parameter in question can be accessed,column 4: the range of values within which the parameter in question can be set,column 5: the value of the parameter in question is set on delivery ex factory.

Parameters having "either/or" validity (software switches) can merely be set to value Ι or ΙΙ . In the caseof such parameters, column 4 is empty.Parameter numbers in acute brackets; e.g. <105>, mean the value (content) set for the parameterin question.

Example:107 Speed for front backtack when <106> = I

I limited by <105>II limited by <607>

Explanation:Parameter 107 is valid only the the value (content) of parameter <106> = I.If parameter 107 is set to I (<107> = I), then the speed for the front backtack is limited by parameter 105,e.g. <105> = 1500. If parameter 107 is set to II (<107> = II), then the speed for the front backtack islimited by the value of parameter 607, e.g. <607> = 4000.

p-70-se-3-en 11.1 04-11-10

p-70-se-3-en 11.2 04-11-10

11.3 Parameter survey P70SE 03 (2A_023_T.ENO)

Function Abbrev’n Parameter Input ConnectionOutput Socket/Contacts

Accelerate DRZAN 722

Automatic corners ECKE 458

Backtack RIE 104/105/107110/140/153154/157/523585/768

Backtack inversion RIV 419/456 E6 X2:10

Backtack suppression RIUNT 419

Band supply BZUF 468

Blower BLA 668

Brake DRZAB 723

Catcher FANG 707

Chopper MESSER 105

Clean-cut CC 793

Control REG 758/884/885886/887/889890/891/894990

Counter ZAE 769

Decorative backtack ZRIE 153/154/157368/369/522523/530/679775

Defect search HWT 797

Delay VERZ 174/189/190307/403/623679/716/730731/732/733739/740/761770/793

Direction of rotation DRR 800

Display ANZ 605

End backtack ER 110/369/604731/732/740

Feed reverse TUM 634/721/733 E5 X2:9768/793

p-70-se-3-en 11.3 04-11-10

Front backtack AR 104/105/106107/140/368739

Hardware test HWT 797

Inverse rotation RDR 618

Machine class MAKL 790

Machine run ML 118

Needle bar NASTA 418/459/987 E1 X2:1E2 X2:2E3 X2:3

Needle cooling NAKU 118

Needle position NAPO 303/522/700701/702/703705/706/707710/768/810

Needle position change-over NPW 446

Needle up without trimming NHOS 446

Number of stitches STZA 111/112/174404/445/459760/769

ON period EINZ 175/189/190715/889

Operator panel BDF 386

Photocell LS 111/112/113199/615

Presser foot PF 554/636/651 E7 X2:11688/729/730770

Program PR 114/206/221304/313/371468/554/851

Programming level C EBC 798

Puller PULL 400/420/445456

Repeat backtack WRIE 731

Residual brake STBR 718

Seam end NE 110

Seam start NA 105

Single stitch EST 446

Soft start SANL 116

p-70-se-3-en 11.4 04-11-10

Speed DRZ 105/106/107110/117/199221/402/403428/530/573574/585/605606/607/608609/676/725850/901

Speed decrease DRZAB 723

Speed increase DRZAN 722

Speed limitation DB 221/402/428 E13 X3:23573/574/585676

Start START 113

Start delay STVERZ 429

Starting block ANLSP 665

Stitch condensation STVD 105/106/107110/419/739

Stitchcounter STZ 725/726/727760/769

Stitchlength STL 386

Stop STOP 114/206/665 E14 X3:25680

Stop time STOPZ 775

Stroke adjustment HV 401/402/403 E17 X3:26404/428

Target stitch PEIPO 147/653/789 E4 X2:4

Thread monitor FW 660/725/726 E11 X1:5727/760/769777

Thread puller FZ 761

Thread tension FS 386

Thread tension release FSL 538/636/688689/707/761

Thread trimming SN 601/604/609705/706/732901/988

Thread wiper WI 668/689/715716

Time needed to switch on EINZ 175/189/190715/889

Timing output TA 538

Two-needle machine ZWN 418

Vacuum SAUG 105

p-70-se-3-en 11.5 04-11-10

p-70-se-3-en 11.6 04-11-10

11.4 List of Parameters P70SE 03 (2A_023_T.EN)

No. Function (Meaning) Level Range of StandardValues Value

104 (AR/RIE) Front backtack correction (delayed B,C 0-15 5 Kl. 1, 2, 3disabling of feed reverse)

105 (AR/RIE/DRZ/MESSER/NA/SAUG/STVD) Speed for B,C 100-6400 1200 Kl. 1, 2front backtack/ stitch condensation 100 - 6400 1000 Kl. 3(11000000)

106 (AR/DRZ/STVD) Speed for front backtack/stitch B,C 0 Kl. 1, 2, 3condensation1 variable (treadle-controlled)0 constant (corresponding to <105>)

107 (AR/RIE/DRZ/STVD) Speed for front backtack/stitch B,C 0 Kl. 1, 2, 3condensation when <106> = I1 limited by <105>0 limited by <607>

110 (ER/RIE/DRZ/MESSER/NE/SAUG/STVD) Speed for B,C 100-6400 1200 Kl. 1, 2end backtack/ stitch condensation 100 - 6400 1000 Kl. 3(01100000)

111 (LS/STZA) Light barrier compensation stitches 1 A,B,C 1-255 6 Kl. 1, 2, 3(stitches from light barrier clear to seam end)

112 (LS/STZA) Number of stitches for light barrier A,B,C 0-255 0 Kl. 1, 2, 3fade-out on knit fabrics (according to stitch size)

113 (LS/START) Start with light barrier B,C 0 Kl. 1, 2, 31 when light barrier is dark only0 also when light barrier is clear

114 (PR/STOP/NE) Stop before seam end after stitch B,C 0 Kl. 1, 2, 3count (last seam section)1 yes0 no

116 (SANL) Soft start stitches A,B,C 0-255 0 Kl. 1, 2, 3(11100000)

117 (SANL/DRZ) Speed for soft start stitches B,C 30-640 400 Kl. 1, 2, 3(00010000)

118 (NAKU/ML) Signal on output is B,C Kl. 1, 2, 31 = needle cooling2 = motor run (sewing cycle)3 = Edge trimmer4 = blower on at treadle -1 and during sewing off5 = blower on at treadle -1 and during sewing on

140 (AR/RIE) Front backtack correction (delayed B,C 0-15 5 Kl. 1, 2, 3enabling of feed reverse)

147 (PEIPO) Move to bearing position B,C 0 Kl. 31 reverse - Kl. 1, 20 forward

153 (ZRIE/RIE) Finish backtack at <523> = I B,C Kl. 1, 2, 31 Start tack is fancy bartack0 Start tack is normal tack

154 (ZRIE/RIE) Fancy at <523> = 1 B,C Kl. 1, 2, 31 Finish tack is fancy bartack0 Finish tack is normal tack

157 (ZRIE/RIE) Start-decorative backtack with third B,C Kl. 1, 2, 3seam section1 yes0 no

174 (VERZ/STZA) Stitches until output Ax on A,B,C 1-255 4 Kl. 3- Kl. 1, 2

175 (EINZ) Time needed to switch on for output Ax B,C 0-2550 50 Kl. 3- Kl. 1, 2

189 (VERZ/EINZ) Delay/on time t1 B,C 0-2550 50 Kl. 3- Kl. 1, 2

p-70-se-3-en 11.7 04-11-10

190 (VERZ/EINZ) Delay/on time t2 B,C 0-2550 50 Kl. 3- Kl. 1, 2

199 (DRZ/LS) Speed for light barrier compensation B,C 300-6400 1200 Kl. 1, 2, 3stitches

206 (NE/PR/STOP) Interrupt/discontinue seam sections B,C 0 Kl. 1, 2, 3at speed = constant (<203> = II)1 with treadle -20 with treadle 0

221 (PR/DB/DRZ) Speed limitation for sewing program 1 B,C 300-6400 1200 Kl. 1, 2, 3(or for all sewing programs)

303 (NAPO) Needle position at the end of a sewing route B,C 0 Kl. 3with end locking without cutting - Kl. 1, 21 position 1 (below)0 position 2 (above)

304 (PR) Stitch compensation at feed reverse for a seam B,C 0-2550 30 Kl. 1, 2, 3section

307 (NAKU/VERZ) time lag for automatic disable of B,C 0-2550 50 Kl. 1, 2, 3output „Ax“ after machine stops

313 (PR) Programs are backtack programs (darning B,C 0 Kl. 1, 2, 3programs)1 yes0 no

368 (AR/RIR/ZRIE) Start bar / decorative start bar is A,B,C 0 Kl. 1, 2, 31 quadruple1 double

369 (ER/RIR/ZRIE) End bar / decorative end bar is A,B,C 0 Kl. 1, 2, 3quadruple with Idouble with II

371 (PR) Last seam line „x“ in the program is recognised, B,C 0 Kl. 1, 2, 3if, in the seam line „x+1“1 the number of stitches is 000 the number of stitches is 00 and neither the start bar nor the end bar is activated.

386 (FS/STL/BDF) Key combination T5 and T2 in B,C 0 Kl. 3OC-TOP operating field means switching on - Kl. 1, 21 Second stitch length0 Second thread tension

400 (PULL) Input „Puller“ B,C 0 Kl. 1, 2, 31 switch operation (flip-flop)0 pushbutton operation

401 (HV) Input „stroke adjustment“ B,C Kl. 31 switch operation - Kl. 1, 20 push-button operation

402 (HV/DRZ/DB) Speed at stroke adjustment B,C 300-6400 1800 Kl. 3- Kl. 1, 2

403 (HV/DRZ/VERZ) Delay (ms) of the speed variation B,C 0-2550 10 Kl. 3at end of stroke adjustment - Kl. 1, 2

404 (HV/STZA) Number of stitches with stroke adjustment B,C 0-255 5 Kl. 1, 20 - 255 0 Kl. 3

418 (NASTA/ZWN) Needle bar shutdown after seam end B,C 0 Kl. 1, 21 both, regardless of inputs - Kl. 30 conforming to inputs

419 (RIV/RIUNT/STVD) Function of external key B,C Kl. 1, 2, 31 backtack / stitch condensation inversion0 backtack / stitch condensation suppression (flip-flop function)

420 (PULL) Puller function B,C 0 Kl. 1, 2, 31 yes0 no

428 (HV/DB/DRZ) Speed limitation at stroke B,C 0-9 1 Kl. 1, 2, 3adjustment adjustable over 10 steps0 = maximum speed (<607>)

p-70-se-3-en 11.8 04-11-10

429 (STVERZ) Start delay after needle bar function B,C 0-2550 120 Kl. 1, 2enabling - Kl. 3

445 (PULL/STZA) Stitches for puller delay A,B,C 0-255 5 Kl. 1, 2, 3446 (NHOS/NPW/EST) Input E2 is B,C 1-3 2 Kl. 1, 2, 3

1 = needle up without trimming2 = needle position change-over3 = single stitch4 = single stitch with reduced length5 = backtack inversion6 = backtack suppression7 = change-over position8 = puller lift switched off(10111000)

456 (RIV/PULL) Input „Eb“ is B,C Kl. 1, 21 backtack inversion - Kl. 30 puller

458 (ECKE/ZWN) Automatic corners A,B,C 0 Kl. 1, 21 yes - Kl. 30 no

459 (NASTA/ZWN/STZA) Stitchcount to needle bar ON A,B,C 1-10 3 Kl. 1, 2- Kl. 3

468 (PR/BZUF) Program „band supply“ B,C 0 Kl. 31 yes - Kl. 1, 20 no

522 (NAPO/ZRIE) Needle position when stop occurs B,C 0 Kl. 1, 2, 3during decorative backtack (stitch in stitch)1 position 2 (up)0 position 1 (down)(10110000)

523 (RIE/ZRIE) Backtack A,B,C 0 Kl. 1, 2, 31 decorative backtack (stitch in stitch)0 standard backtack(01110000)

530 (DRZ/ZRIE) Speed (max.) for decorative backtack B,C 100-2000 1000 Kl. 1, 2, 3(11110000)

538 (FSL/TA) Timing of output Ax (thread tension release) B,C 0-100 40 Kl. 1, 2, 3(0 = 100%)

554 (PF/PR) Presser foot position after seam section B,C Kl. 1, 2, 3stitch count and treadle position > +11 up0 down

573 (DRZ/DB) Speed limitation B,C 300-6400 2800 Kl. 3- Kl. 1, 2

574 (DRZ/DB) Speed limitation B,C 300-6400 2200 Kl. 3- Kl. 1, 2

585 (DRZ/DB/RIE) Speed limitation B,C 300-6400 3000 Kl. 1, 2, 3601 (SN) Trimming B,C Kl. 1, 2, 3

1 yes0 no(00001000)

603 (START) Start after seam end B,C Kl. 1, 2, 31 after treadle 0 only0 immediate start of operation

604 (SN/ER) Trimming after single end backtack B,C Kl. 1, 2, 31 forward0 backward

605 (DRZ/ANZ) Actual speed in display B,C 0 Kl. 1, 2, 31 yes0 no

606 (DRZ) Speed: level 1 (min.) B,C 30-640 180 Kl. 1, 2, 3(10001000)

607 (DRZ) Speed: level 12 (max.) B,C 100-6000 1200 Kl. 1, 2(01001000) 100 - 6000 3200 Kl. 3

p-70-se-3-en 11.9 04-11-10

608 (DRZ) Speed level curve (treadle characteristic) B,C Kl. 1, 2, 31 linear0 not linear

609 (SN/DRZ) Trimming speed 1 B,C 30-300 180 Kl. 1, 2, 3(11001000)

615 (LS) End recognition when photocell goes B,C 0 Kl. 1, 2, 31 from light to dark0 from dark to light

618 (RDR) Inverse rotation after seam end B,C Kl. 1, 2, 31 yes0 no(00101000)

623 (RDR/VERZ) Delay in start-up time (ms) for inverse B,C 0-2550 50 Kl. 1, 2, 3rotation

634 (NPW/TUM) Function of external key (input) B,C 0 Kl. 1, 2, 31 TUM while the machine is stopped and while motor is running0 NPW while the machine is stopped TUM while motor is running(01110000)

636 (FSL/PF) thread tension release in conjunction B,C 0 Kl. 1, 2with presser foot Kl. 31 yes0 no

651 (PF) Presser foot with automatic descent on B,C Kl. 1, 2, 3machine stop1 yes0 no

653 (PEIPO) Target stitch before sewing B,C 0 Kl. 1, 2, 31 yes0 no(11111000)

660 (FW) Bobbin thread monitoring B,C 0 Kl. 1, 2, 30 without (= *II*)1 via a sensor (= **I*)2 by a stitch count(11111000)

665 (ANLSP/STOP) Run locking/stop C Kl. 1, 2, 31 contact closed0 contact open

668 (BLA/WI) Thread wiper/thread clearer B,C Kl. 1, 21 yes 0 Kl. 30 no(10101000)

676 (DRZ/DB) Speed limitation via potentiometer at B,C Kl. 1, 2, 3the SERVO-TOP control or via the keys V+ / V- atthe MINI-STOP control1 yes0 no

679 (ZRIE/VERZ) Fancy tack: time from positioning to B,C 0-2550 40 Kl. 1, 2, 3switch-on of reverse feed

680 (STOP/ANLSP) Signal at input stop/run locking B,C Kl. 1, 2, 3causes (in case of <669> = I)1 discontinuation of the functional sequence0 interruption of the functional sequence

688 (FSL/PF) thread tension release in conjunction with B,C 0 Kl. 1, 2, 3the presser foot at stop in the seam, when <636> = I1 yes0 no

689 (WI/FS/FSL) wiper output used for B,C Kl. 1, 2, 31 wiper0 thread tension

p-70-se-3-en 11.10 04-11-10

700 (NAPO) Needle position 0 B,C 0-239 0 Kl. 1, 2, 3 *(reference position of the needle)(01101000)

701 (NAPO) Angular adjustment B,C Kl. 1, 2, 31 with handwheel (teach-in)0 by keys (+/-)

702 (NAPO) Needle position 1 (needle down) B,C 0-239 75 Kl. 1, 2, 3(11101000)

703 (NAPO) Needle position 2 (thread take-up lever up) B,C 0-239 213 Kl. 1, 2, 3(00011000)

705 (NAPO/SN/TA) Needle position 5 (end of trimming B,C 0-239 175 Kl. 1, 2, 3signal 1 (magnetic thread trimmer) / clock pulsesstart of the trimming signal 1)(10011000)

706 (NAPO/SN) Needle position 6 (start trimming signal 2 B,C 0-239 80 Kl. 1, 2, 3(pneumatic thread trimmer))(01011000)

707 (NAPO/FSL/FANG) Needle position 9 B,C 0-239 180 Kl. 1, 2, 3(thread tension release or thread catcher start)(01011000)

710 (NAPO/NHOS) Needle position 3 (needle up) B,C 0-239 200 Kl. 1, 2, 3(11011000)

715 (EINZ/WI) Duration (ms) of thread wiper B,C 0-2550 40 Kl. 1, 2, 3716 (VERZ/WI) Delay in start-up time (ms) for thread B,C 0-2550 120 Kl. 1, 2, 3

wiper718 (STBR) Timing of residual brake B,C 0-100 0 Kl. 1, 2

(0 = brake off) 0 - 100 8 Kl. 3(00111000)

721 (TUM/TA) Timing output A5 (feed reverse) B,C 0-100 40 Kl. 1, 2, 3(0 = 100% switched on)

722 (DRZAN) Acceleration ramp B,C 1-50 40 Kl. 1, 2, 31 gradual50 steep

723 (DRZAB) Brake ramp B,C 6-50 25 Kl. 1, 2, 31 gradual50 steep

725 (STZ/DRZ/FW/ANZ) Display on operator panel B,C Kl. 1, 2, 31 actual speed0 remaining stitches for bobbin thread

726 (STZ/FW) counter for bobbin thread monitoring is B,C 0 Kl. 1, 2, 31 activated0 deactivated

727 (STZ/FW) counter for bobbin thread monitoring lead B,C 0 Kl. 1, 2, 3to1 Stop and signal at output Ax0 Signal at output Ax without stop

729 (STVERZ/PF) Start delay after lowering presser foot B,C 0-2550 140 Kl. 1, 2, 3730 (PF/VERZ) Lift delay for presser foot after seam end B,C 0-2550 50 Kl. 1, 2, 3731 (ER/WRIE/VERZ) Delay before stitch counting for B,C 0-2550 160 Kl. 1, 2

end backtack (ERV) 0 - 2550 120 Kl. 3732 (SN/ER/VERZ) Delay (ms) for trimming after single B,C 0-2550 30 Kl. 1, 2, 3

end backtack733 (TUM/VERZ) time lag between feeder change B,C 0-2550 50 Kl. 1, 2

enable and motor start 0 - 2550 0 Kl. 3739 (AR/STVD/VERZ) Delay (ms) for speed after front B,C 0-2550 120 Kl. 1, 2, 3

backtack / stitch condensation740 (ER/WRIE/VERZ) Delay before stitch counting for B,C 0-2550 60 Kl. 1, 2, 3

end backtack backward758 (REG/DRZAB) Deceleration ramp B,C 0 Kl. 1, 2, 3

1 braking as per <723>0 braking with maximal moment

p-70-se-3-en 11.11 04-11-10

760 (FW/SPFW/STZ/STZA) B,C 10-2550 100 Kl. 1, 2, 3- Stitch count for the remnant thread after thebobbin thread monitor responds with direct bobbinthread monitoring- Multiplicator for the fixed value (200) fordetermining the start value of the stitch counterwith indirect bobbin thread monitoring

761 (FSL/FZ/VERZ) Prolongation Thread tension release/ B,C 0-2550 0 Kl. 1, 2, 3Thread puller

768 (TUM/NAPO/RIE/ERIE) Needle position for backtack B,C 0-239 60 Kl. 1, 2correction 0 - 239 150 Kl. 3

769 (FW/ZAE/STZ/STZA) Stitches (remaining thread B,C 10-2550 100 Kl. 1, 2, 3length) for the stitchcounter for the indirectbobbinthreadmonitoring

770 (PF/VERZ) Lifting delay of presser foot at threadle- B,C 0-2550 50 Kl. 1, 2position „-1“ 0 - 2550 100 Kl. 3

775 (ZRIE/STOPZ) Stop time (ms) with stitch in stitch B,C 0-2550 200 Kl. 1, 2, 3backtack (decorative backtack)

777 (FW) Reset duration for bobbin monitor B,C 10-2550 100 Kl. 1, 2, 3MK 1420

789 (PEIPO) Needle position 10 B,C 0-239 225 Kl. 1, 2, 3(target stitch)

790 (MAKL) Program selection for machine classes by B,C 1-3 2 Kl. 1, 2operators box 1 - 7 3 Kl. 3(11111100)

793 (VERZ/TUM/CC) delay (ms) between feeder B,C 0-2550 140 Kl. 1, 2, 3change enable and cutting for shortened cuttingstitch

797 (HWT) Hardware test B,C 0 Kl. 1, 2, 31 yes0 no

798 (EBC) Programming level C B,C 0 Kl. 1, 2, 31 yes0 no

799 (MAKL) Machine class which has been selected B,C 1-3 1 Kl. 1(10111000) 1 - 3 2 Kl. 2

1 - 3 3 Kl. 3800 (DRR) Direction of motor rotation viewed from belt B,C Kl. 1, 2, 3 *

pulley1 left-hand rotation0 right-hand rotation(01111000)

801 (RDR) Reverse rotation angle after seam end B,C 5-200 30 Kl. 1, 2, 3810 (NAPO) Machine positions in position 2 after B,C 0 Kl. 1, 2, 3

enabling1 yes0 no

850 (DRZ) Maximum motor speed C 2000-6000 4500 Kl. 1, 2, 3851 (PR/DRZAB) Brake ramp for stitch-count seams C Kl. 1, 2, 3

1 steep0 gradual

884 (REG) Proportional amplification of the speed control B,C 4-50 11 Kl. 1(in general) 4 - 50 15 Kl. 2, 3

885 (REG) Integral amplification of the speed control C 0-100 30 Kl. 1, 2, 3886 (REG) Proportional amplification of the order C 1-50 20 Kl. 1, 2, 3

controllers887 (REG) Differential amplification of the order C 1-100 30 Kl. 1, 2

controllers 1 - 100 100 Kl. 3889 (EINZ/REG) Time required for order controlling C 0-1000 400 Kl. 1, 2

(0 = always) 0 - 1000 800 Kl. 3890 (REG) Proportional amplification of the superior C 1-50 25 Kl. 1, 2, 3

order controllers for the residual brake

891 (REG) Proportional amplification of the lower speed C 1-50 20 Kl. 1, 2, 3controllers for the residual brake

894 (REG) Rotational direction of motor and synchronizer C Kl. 1, 2, 31 different0 same

901 (DRZ/SN) Trimming release speed C 30-500 300 Kl. 1, 2, 3909 (FZ) Thread puller on/off B,C 0 Kl. 1, 2, 3

1 on0 off(11111000)

910 (FZ) Thread puller delay B,C 10-2550 100 Kl. 1, 2, 3933 (ANZ) Display change-over C 0 Kl. 1, 2, 3

1 diagnosis0 normal display

987 (NASTA) Switch-off position for needle bars C 0-127 120 Kl. 10 - 127 100 Kl. 2

- Kl. 3988 (SN) Shortened cut stitch B,C 0 Kl. 1, 2, 3

1 yes0 no

990 (REG) Removal of setpoint position upon C 0-255 32 Kl. 1, 2, 3change-over from speed control to position control

p-70-se-3-en 11.12 04-11-10

X3

12. Electrical Connections Diagramm P70SE

X3X2

+24V

A2

A10

A3

A4

A13

A6

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

A9

A12

A18

A8

A7

A14

A29

0V

E20

Y10Y3

Y2

Y5

Y4

Y15Y7

Y12Y18

113

25 14

1

20

19

37

159

1 8

A5

A15

0V

0V

E13

E15

E14

E17

E18

E19

E21

A30

A31

A32

A33

A34

A35

A36

Y13Y6

Y9

Y14

Y30Y31

Y32

S14

S13S15

X1 X4

S17

Y33

Y36

S18

P70SE12 12.1 04-11-10

S21S20

Y34Y35

H8

Y8

S19

0V

X4

0V

0V

A10

A2

E23

1

3

4

5

6

7

8

9

10

11

12

13

14

15

25

24

23

22

21

20

18

17

16

E22

A3

A4

A13

E19

X2

X1

+24V

A40

A39

E20

E18

E17

A37

+24V

+24V

A18

A12

A9

A6

E2

E3

E4

A20

A21

A22

A23

E5

E6

E7

A24

A25

A26+24V

2

1

3

4

5

6

7

8

9

10

11

12

13

1415

0V

E16

E12

A11

E11

+5V

A19

+24V

2

1

3

4

5

6

7

8

Y12Y9

Y18

Y6Y13

Y3Y4

Y10Y2

S17

FWSÄUB

NFW

RESET

SFW

ZS

S1S2

S4

S6

S3

S5

S7

H1

H3

H6

H2

H7

H5

H4

7 6

1

8

3

24 5

FW

Y37

S18

E1

19

P70SE12 12.2 04-11-10

S23

S22

A38 Y38

S19

P70SE12 12.3 04-11-10

Bedeutung der Magnete bzw. Magnetventile, Taster / Meaning of magnets and/or solenoids and keysSignification des aimants resp. solenoides et touches / Significação dos imaõs e/ou as solenoidas e teclasSignificato dei magneti, delle valvole magnetiche e dei tasti / Significación de los imanes y/o los solenoides ypulsadores / Betekenis van de magneten resp. magneetkleppen, toetsenMK1 : <799> = 1 (Kl 1422-S) MK2 : <799> = 2 (Kl 1422-L) MK3 : <799> = 3 (Kl 1425)

FW Fadenwächter / thread monitor / garde-fil /guarda da linha / controllafilo / guardahilos / draadcontrole

S2

S2

S1

<799> = 1/2<790> = 1/2

Zwei Nadeln eingeschaltet / two needles on / deux aiguilles en fonction /ligar dois agulhas / inserire due aghi / conectar dos agujas /twee naalden inschakelen

<799> = 1/2<790> = 1/2

S1

<799> = 1/2<790> = 3<634>

Transportumstellung von Hand / manual feed reverse /renversement de marche manuel / mudança do transporte manual /commutazione trasporto a mano / inversión de transporte manual /handmatige transportomschakeling

<799> = 3<634>


S3

<799> = 1/2

S3

<446> = 1<799> = 3

Nadel hoch ohne Schneiden / needle up without thread trimming /aiguille en haut sans coupe / agulha para cima sem corte de linhas /ago su senza taglio / aguja arriba sin corte /naald omhoog zonder snijden

Rechte Nadel ausgeschaltet / right needle off /aiguille à droite éliminée / agulha direita desligada /disinserire l'ago destro / aguja derecha apagada /rechtse naald uit

Linke Nadel ausgeschaltet / left needle off /aiguille à gauche éliminée / agulha esquerda desligada /disinserire l'ago sinistro / aguja izquierda apagada /links naald uit

E11, E12, E16, A11,A19

S3 Nadelpositionswechsel / needle position change-over /changement de position d´aiguille / troça de posição da agulha /cambio di posizione dell´ago / cambio de posición de aguja /naaldpositie-verwisseling<446> = 2

<799> = 3

S3 Einzelstich / single stitch / point unique /ponto individual / punto singolo / puntada individual / enkele steek

<446> = 3<799> = 3

Peilposition / target stitch /point cible / posição correto da penetração da agulha /rilevamento / posición "poil" /peilstand

S4

<799> = 1/2

S4

<799> = 3<790> = 3/4/5/7

Hubverstellung / stroke adjustment /variation de course / alteração do curso /regolazione della corsa / ajuste de carrera /hefhoogteverstelling

P70SE12 12.3 04-11-10


S5

<799> = 1/2<634>


S5

<799> = 3<790> = 4/5

Zweite Stichlänge Obertransport / second stitch length top feed /2e longueur de point transport supérieur / segundo comprimento de pontotransporte superior / seconda lunghezza punti trasporto superiore / la segundalongitud de puntada del transporte superior / tweede steeklengte boventransport

S5

<799> = 3<790> = 6/7

Kantenschneider / edge trimmer /coupe de bord / corte cantos /rasa bordi / corta bordes /zoomsnijder

S6

<799> = 1/2

Zweite Stichlänge Unter- bzw. Haupttransport / second stitch length bottom ormain feed / 2e longueur de point transport inférieur ou principal / segundocomprimento de ponto transporte inferior ou principal / seconda lunghezza puntitrasporto principale o inferiore / la segunda longitud de puntada del transporteinferior o principal / tweede steeklengte onder- resp. hoofdtransport

S6

<799> = 3<790> = 2/3/5/7

Nachfolgende Riegelfunktion invertieren / invert subsequent backtack function /inverser la prochaine fonction de bridage / inverter o próximo remate /invertire la funzione d'affr. successiva / invertir la próxima función de remate /inverteren op elkaar volgende hechtfunctie

S5 Riegelunterdrückung / backtack suppression /suppression de bridage / supressão do remate /soppresione dell’ affrancatura / supresión del remate /onderdrukking van het strookje<799> = 3

<790> = 1/2/3<419> = ΙΙ

S5

<799> = 3<790> = 1/2/3<419> = Ι

Nachfolgende Riegelfunktion invertieren / invert subsequent backtack function /inverser la prochaine fonction de bridage / inverter o próximo remate /invertire la funzione d'affr. successiva / invertir la próxima función de remate /inverteren op elkaar volgende hechtfunctie

S7

<799> = 1/2<790> = 2

Presserfuß und Nadel hoch, Antrieb gesperrt / presser foot and needle up, drivesystem locked / pied presseur et aiguille en haut, système bloqué / calcador eagulha para cima, accionamento bloqueado / alzapiedino e ago su, motoredisabilitato / prensatelas y aguja arriba, accionamiento bloqueado / drukvoet ennaald omhoog, aandrijving geblokkeerd

S7

<799> = 3

Drehzahlbegrenzung 1 / speed limitation 1 / limitation de vitesse 1 /limitação das rotações 1 / limitazione velocità 1 / limitación de velocidad 1 /beperking van het toerental 1

S13

Zweite Stichlänge Unter- bzw. Haupttransport / second stitch length bottom ormain feed / 2e longueur de point transport inférieur ou principal / segundocomprimento de ponto transporte inferior ou principal / seconda lunghezza puntitrasporto principale o inferiore / la segunda longitud de puntada del transporteinferior o principal / tweede steeklengte onder- resp. hoofdtransport

<573> limit

n

S14STOP

STOP

P70SE12 12.4 04-11-10

Drehzahlbegrenzung 2 / speed limitation 2 / limitation de vitesse 2 /limitação das rotações 2 / limitazione velocità 2 / limitación de velocidad 2 /beperking van het toerental 2limit

nS15


<574>

S20 Bandschieber vorn / tape slide in front

S21 Bandschieber hinten / tape slide in the back

S22 Bandschieber / tape slide

S23 Bandschneider / tape cutter

S19 Puller / puller /puller / puller /puller / estirar / puller

<468> = I

<468> = I

<468> = I

<468> = I

Drehzahlbegrenzung 3 / speed limitation 3 / limitation de vitesse 3 /limitação das rotações 3 / limitazione velocità 3 / limitación de velocidad 3 /beperking van het toerental 3limit

S18

<585>

n

S17 Hubverstellung / stroke adjustment /variation de course / alteração do curso /regolazione della corsa / ajuste de carrera / hefhoogteverstelling

Y3I max0,35 A

Fadenwischer / thread wiper / écarteur de fil /retira-linhas / scartafilo / retirahilos /draadwisser

Y4I max0,35 A

Presserfuß heben / lifting presser foot / relevage du pied presseur /levantar do calcador / sollevamento del alzapiedino /elevación de prensatelas / drukvoet optillen

Transportumsteller / feed reverse / renversement de marche /mudança do transporte / commutazione trasporto / inversión de transporte /transportomschakeling

Y5I max0,35 A

Y2I max8 A *

Fadenschneider / thread trimmer / coupe-fil /corte de linhas / rasafilo / cortahilos /draadsnijder

Y6I max0,35 A

<799> = 1/2

Rechte Nadel ausgeschaltet / right needle off /aiguille à droite éliminée / agulha direita desligada /disinserire l'ago destro / aguja derecha apagada /rechtse naald uit

P70SE12 12.5 04-11-10


Hubverstellung / stroke adjustment /variation de course / alteração do curso /regolazione della corsa / ajuste de carrera /hefhoogteverstelling

Y6I max0,35 A

<799> = 3<790> = 3/4/5/7

Fadenspannungslösen / thread tension release /détendeur de fil / soltar tensão da linha /sbloccaggio tendifilo / detensión del hilo /verbreken van de draadspanning

Y10I max8 A *Y12I max0,35 A<799> = 3

Stichlängenumschaltung unten / stitch length change-over down / commutationlongueur de point en bas / mudança de comprimento dos pontos em baixo /commutazione lunghezza punti giù / cambio de longitud de la puntada abajo /steeklengteomschakeling beneden

Y9I max0,35 A

<799> = 3

Stichlängenumschaltung oben / stitch length change-over up /commutation longueur de point en haut / mudança de comprimento dos pontos emcima / commutazione lunghezza punti su / cambio de longitud de la puntada arriba /steeklengteomschakeling boven

Y9I max0,35 A

<799> = 1/2

Linke Nadel ausgeschaltet / left needle off /aiguille à gauche éliminée / agulha esquerda desligada /disinserire l'ago sinistro / aguja izquierda apagada /links naald uit

Puller / puller /puller / puller /puller / estirar / puller

Y13I max0,35 A

Y8I max0,35A<468> = Ι

Bandklemme lösen / tape clamp release

Y7I max0,35 A

Presserfußdruck / presser foot pressure /pression du pied presseur / pressão do calcador /pressione alzapiedino / presión del prensatelas / naaivoetdruk

Y14I max0,35 A

Fadenspannungsumschaltung / thread tension change-over / commutation detension du fil / mudança da tensão da linha / commutazione tenditura del filo /cambio de la tensión del hilo / draadspanningsomschakeling

Puller 2 / puller 2 /puller 2 / puller 2 /puller 2 / estirar 2 / puller 2

Y15I max0,35 A

Y18I max0,35 A

Kantenschneider / edge trimmer /coupe de bord / corte cantos /rasa bordi / corta bordes /zoomsnijder

P70SE12 12.6 04-11-10


A20I max20 mA

Anzeige H1 (S1) / display H1 (S1) /affichage H1 (S1) / indicação H1 (S1) /visualizzazione H1 (S1) / indicador H1 (S1) /indicatie H1 (S1)

A23I max20 mA

Anzeige H4 (S4) / display H4 (S4) /affichage H4 (S4) / indicação H4 (S4) /visualizzazione H4 (S4) / indicador H4 (S4) / indicatie H4 (S4)


A25I max20 mA


A24I max20 mA

A26I max20 mA


A29I max20 mA

Anzeige H8 (Spulenfadenwächter) / display H8 (bobbin thread monitor) /affichage H8 (garde-fil) / indicação H8 (guarda da linha) /visualizzazione H8 (controllafilo) / indicador H8 (guardahilos) / indicatie H8(draadcontrole)

A22I max20 mA


A21I max20 mA


480 Impulse pro Umdrehung (FA) / 480 pulses per revolution (FA) /480 impulsions/révolution (FA) / 480 impulsos/rotação (FA) /480 impulsi/giro / 480 impulsos/revolución (FA) /480 pulsen per omwenteling (FA)

Y32I max0,35A 480I/U

480 Impulse pro Umdrehung (FB) / 480 pulses per revolution (FB) /480 impulsions/révolution (FB) / 480 impulsos/rotação (FB) /480 impulsi/giro (FB) / 480 impulsos/revolución (FB) /480 pulsen per omwenteling (FB)

Y31I max0,35A 480I/U

Y30I max0,35 A 1I/U

Zählsignal / count signal / signal de comptage /sinal de contagem / segnale conteggio / señal del contador /telsignaal

Y33I max0,35A

Fadenklemme / thread clamp /serre-fil / pinça fixa a linha /serrafilo / garra de hilo / draadklem

P70SE12 12.7 04-11-10


Y34I max0,35A<468> = Ι

Bandschieber / tape slide

Y38I max0,35A

Reinigung Fadenwächter / cleaning thread monitor

Maschinenlauf / motor runs / moteur en marche / motor em movimento /funzionamento motore / motor en marcha / loop van de machine

Y37I max0,35 A

Y36I max0,35A

Signal nach Stichzählung / signal after stitch count

Y35I max0,35A<468> = Ι

Bandschneider / tape cutter

Y37I max0,35 A

Nadelkühlung / needle cooling /refroidissement d’aiguille / refrigeração da agulha /rafreddamento ago / refrigeración de aguja /naaldkoeling

<118> = I<307>

<118> = II

� Die Summe der Lastströme aller gleichzeitig eingeschalteten Stellglieder (Magnete, Magnetventile)darf den Wert von 4A nicht überschreiten (siehe hierzu Kapitel 2. Technische Daten).

� The total of load currents of all servos activated simultaneously (solenoids, solenoid valves)is not allowed to exceed 4 amps (see also section 2, Technical Specifications).

� Le total des courants de charge de tous les vérins (aimants, électro-vannes) activés simultanémentne doit pas dépasser 4 A (voir aussi le chapitre 2, "caractéristiques techniques")

� A soma das correntes sob carga de todos os actuadores ligados ao mesmo tempo (ímans,solenóides) não pode ultrapassar o valor de 4A (ver também capítulo 2, Dados Técnicos).

� La somma delle correnti di carico di tutti gli attuatori inseriti contemporaneamente(magneti, elettrovalvole) non deve essere superiore a 4 A (vedere il capitolo 2 dati tecnici).

� La suma de las corrientes bajo carga de todos los elementos de todos los componentes de regulaciónconectados simultáneamente (imanes, válvula magnética) no podrá sobrepasar el valor de 4A (véasetambién el capítulo 2. de datos técnicos).

� De belastingsstroom van alle tegelijkertijd ingeschakelde bedieningsschakels (magneten,magneetventielen) mag in totaal niet meer dan 4 A bedragen (zie hiervoor hoofdstuk 2. Technischegegevens)

13. Maintenance and Repair

!! Before starting maintenance or repair work, switch off the SERVO-TOP,separate the drive system from mains power (for instance by pulling out the mains plug)and wait for the motor to come to a complete stop.

General maintenance work must only be done by specially trained personnel paying closeattention to the operating instructions.

The SERVO-TOP ist largely maintenance-free.However, make sure to perform the following maintenance work:

Depending on the operating conditions, clean the drive system regularly, at least once a week, from anydust or lint. Make sure in particular that the ventilation louvres and cooling fins of the motor, especially thecooling fins between the motor and the control box, are perfectly clean (Fig. 13).

Important!Blow here! Fig. 13

Remove any threads caught on the synchronizer shaft or on the belt pulley and/or motor shaft.

Check if the drive system is perfectly secured to the stand and that the accessories (synchronizer onmachine shaft, speed control unit on control box) are safely mounted in their respective positions.

Check the drive belt for any wear and for correct tension.Incorrect belt tension can increase noise and vibrations.

When opening covers or removing parts, apart from those removable by hand,live elements can be exposed.Connections can also be electrically live.

If you require to open the drive system before starting maintenance or repair work or before replacing anyparts, disconnect the drive system from any and all power sources.

If maintenance or repair work on the open unit is unavoidable, this may only be done by qualifiedpersonnel familiar with the risks involved. Observe all regulations as per EN 50110.

There can still be capacitors carrying a charge in the power electronics system, even when the drivesystem has been disconnected from all power sources. To avoid injury by electrical shock, it is thereforeessential to wait at least 10 minutes between mains power shutoff and opening the control box.

In order to protect semi-conductor components from overvoltage, use only high-resistivity measuringequipment when making checks on the control system.

Any repair or servicing work requiring skilled knowhow may only be done by qualified personnel authorizedby Quick-Rotan.

We emphasize that in accordance with the product liability law we are under no responsibility for damagescaused by our products if these are due to

- unqualified repair- the use of components not authorized by us- actions made by any persons not authorized by us.

SER13E 13.1 150295

Type P70SE - Fuchs · PDF file11. Survey and List of Parameters 11.1 Explanation of Parameter...

Documents

Transcript of Type P70SE - Fuchs · PDF file11. Survey and List of Parameters 11.1 Explanation of Parameter...