TYLDEN HERITAGE MAIL ORDER PARTS CATALOGUE...S eRubb rP a ts ec ti onp rt 2260 f m un g d h options....

TYLDEN HERITAGE

MAIL ORDER

PARTS CATALOGUE

Custom Classic Truck & Tractor Restorations Business Hours: 0428 507 408

Location: 1906 Trentham Road, Kyneton Vic 3444 Australia

Note: Our workshop & warehouse are only open by

appointment Postal Address: P.O. Box 614, Kyneton Vic 3444

Australia Supplier of Genuine Mack and Reproduction Restoration Parts

Big range of Mack ‘B’ & “R” Model bits. Special Interest in:

Mack Trucks...........Diamond T Trucks......Caterpillar Tractors Trading since 1961

Email: [email protected] Web: www.tyldenheritage.com.au Lee No 3 Pty Ltd – A.C.N. 005 204 599 A.B.N. 40 005 204 599

Costs shown are subject to change without notice. These pages may only be reproduced after obtaining written permission from

Tylden Heritage All rights reserved.

mailto:[email protected]

http://www.tyldenheritage.com.au/

31 May 2020

TYLDEN HERITAGE MAIL ORDER PARTS CATALOGUE of 129

TYLDEN HERITAGE

MAIL ORDER PARTS CATALOGUE

Contents INDEX ................................................................................................................................................. 3

SECONDHAND B MODEL PARTS ...................................................................................................... 4

ENGINE .............................................................................................................................................. 7

B MODEL CHASSIS ............................................................................................................................ 9

B MODEL BONNET .......................................................................................................................... 12

B MODEL CABIN INTERIOR PARTS ................................................................................................ 17

B MODEL CABIN EXTERIOR PARTS .................................................................................................. 21

B MODEL DOOR PARTS .................................................................................................................. 23

SECTION 1 - AXLE, HUB, CHASSIS .................................................................................................. 26

BRAKES............................................................................................................................................. 28

BULLDOGS ....................................................................................................................................... 33

CATCHES, LOCKS & CLIPS ................................................................................................................ 35

REMANUFACTURED AND ............................................................................................................... 42

CAST PARTS ..................................................................................................................................... 42

DRESS UP PARTS .............................................................................................................................. 51

ELECTRICAL ...................................................................................................................................... 55

FITTINGS .......................................................................................................................................... 68

PARTS BOOKS .................................................................................................................................. 74

RUBBER PARTS ................................................................................................................................ 76

STEEL INFORMATION PLATES ........................................................................................................ 90

INFORMATION LABELS .................................................................................................................... 93

R SERIES MACK CHASSIS PARTS .................................................................................................. 101

R SERIES MACK ENGINE PARTS ................................................................................................... 105

R MODEL - BONNET JEWELLERY ETC. ......................................................................................... 109

R MODEL - CABIN INTERIOR ......................................................................................................... 114

R MODEL CABIN EXTERIOR .......................................................................................................... 121

R MODEL - DOORS ........................................................................................................................ 126

31 May 2020


INDEX

B MODEL MACK

NEW & USED PARTS

ENGINE PARTS PART No 1 - 75

BONNET PART No 76 - 145

CABIN INTERIOR PART No 151 - 201

CABIN EXTERIOR PART No 203 - 223

DOORS PART No 224 - 259

GENERAL PARTS

AXLE, HUBS & CHASSIS PART No 266 - 291

BRAKES PART No 399 - 526

BULLDOGS PART No 630 - 677

CATCHES, LOCKS & CLIPS PART No 685 - 970

CAST PARTS PART No 1010 - 1190

DRESS UP PARTS PART No 1200 - 1301

ELECTRICAL PART No 1401 - 1675

FITTINGS PART No 1701 - 1955

PARTS BOOKS PART No 2001 - 2086

RUBBER PART No 2101 - 2534

STEEL INFORMATION PLATES PART No 2601 - 2669

VINYL INFORMATION PLATES PART No 2701 - 2900

R MODEL MACK

AXLE, HUBS & CHASSIS PART No 3501 - 3529

ENGINE PARTS PART No 3701 - 3821

BONNET PART No 4101 - 4243

CABIN INTERIOR PART No 4401 - 4647

CABIN EXTERIOR PART No 4700 - 4817

DOORS PART No 5001 - 5070

TRADING SINCE 1962

31 May 2020


SECONDHAND B MODEL PARTS

ALL PRICES SUBJECT TO GST ENGINE - COMPLETE 711 engine or END673D 7801 - used (ask for details of model &

available). Note: Engine prices are subject to condition and

accessories fitted.

$ 4,095.00

B MODEL GEAR BOXES & PARTS Gear Box 10 or 15 speed sold with money back guarantee, if

returned within 4 weeks less freight cost $ 1,500.00

Gear Boxes - 18 Speed Quad. Sold with money back guarantee if

returned within 4 weeks less freight paid $ 2,000.00

Joey box ex B Model with chassis support brackets. 3 Speed Spicer

Brown Lipe Model 8031 with hand brake. Good Condition. Sold

with money back guarantee if returned within 4 weeks less freight

paid. T1070 B - 5KO892-11KBA60798 - $2,500

$ 2,520.00

B 61 & similar model radiator core only - looks OK -BUT NOT

TESTED - used $ 290.00

B MODEL REAR AXLE DIFF CENTRES Front and rear diff centres for parts only - 6.34 ratio - rust on bull

gear - sold per each $ 254.50

DRIVE AXLE ASSEMBLYS B Model Single axle diff 4.25 Ratio complete h u b to hub with

spider hubs - used $ 1,818.00

B MODEL REAR AXLE DIFF CENTRES Note: There are two bolt patterns, one has 10 studs and the other

type has 16 mounting studs. Axle splines can also vary.

B Model Set tandem diff centres only Set front & rear diff centres,

ratio 4.53 & 4.50. Price per set. Suit B Model tail shaft. $ 2,272.50

R MODEL REAR AXLE Diff - hub to hub ex R Model single drive rear axle model

single drive. 4.24

$ 1,500.00

B MODEL FRONT AXLE - COMPLETE B Model Front axle FA522 larger capacity complete flat end caps

RHD - used. $ 846.00

B Model Front Axle FA 505 lighter capacity complete hubcap type,

RHD, d o e s not include hubcaps - used $ 360.00

We also have front 10stud B Mack front axles. LHD and no brakes. OPTIONAL STEERING COLUMN FOR LARGER

DRIVERS.

B 75 Model Steering Column without box for B73, B75, B77,

B615 & bracket. Note: this has unit that allows a lot better steering

wheel angle & driver gut clearance will not fit to standard B61 type

steering box and only suitable when later type steering box is used

that has separate steering column. Supplied with dash bracket.

$ 240.00

POWER STEERING Original power assist booster type steering kit - fits B Mack - Used

(note: pump not included) as taken off used trucks, add $500 - to

cost for belt driven pump or standard generator drive pump. See

engine parts in next section for pump options.

$ 2,750.00

B MODEL SECONDHAND PARTS

31 May 2020



ALL PRICES SUBJECT TO GST FRONT SPRING HANGERS B61 type front spring hangers L&R $ 182.00

B61 type rear front spring hangers. L&R. (photos includes front

cab mounting) $ 182.00

TAIL SHAFT PARTS B Model Centre Bearing & short jack shaft for wheel base

extension - used $ 455.00

SPRING INSULATOR SEE RUBBER SECTION PART No 2441 FOR OPTIONS $ 75.00

TRUCKS FOR SALE Rare Mack B77 (Note: this is a sample photo only). 228-inch WB

Cabin inside & Out, guards & bonnet have been grit blasted, small

amount of rust repaired. Budd Wheels, high ratio diffs. Chassis &

body ready for painting. Only 113 ever built. This truck comes

with Cummins big Cam, 13 speed & 3 speed Spicer Joe box.

Original build sheet available.

$ 30,000

Incl GST

1955 Mack LTH, west coast off highway, ex super log truck,

(original build other than Motor upgrade to 335hp) duplex gearbox

& Spicer Joe giving 3 gear sticks, Mack dual Reduction diffs,

good tyres, power steering, early pedestal mount air seat,

Super rare truck find, even in the USA. Build sheet available.

(has been parked in a shed last 36 years)

$ 40,000

Incl GST

B61RT 45663 Single axle long WB 13ft8” (suit tray truck) with

spring hangers. Front & rear axles. This has been sandblasted and

painted with high build undercoat. We did plan to use this chassis

for our rare B Model integral sleeper cab which is also listed for

sale and if you decided to do the same you would finish with a

rare and interesting truck in Australia (See bottom photo) of a

similar finished truck to that we proposed

$ 2,500


31 May 2020



TRUCKS FOR SALE (CONT) ALL PRICES SUBJECT TO GST Mack B Model Integral Rare Sleeper Cabin. This is part re

build with many of the Sections new and will be completed with

doors. Ready for painting

Steel tipper body 15ft (4550mm) long. Good telly hoist. New barn

door Tail board, floor has been cut out but not replaced

$ 1,500

TRACTORS FOR SALE Caterpillar D6 1949. Runs and drives OK. Has Cat PCU. Has faulty

low gear and pilot. Motor will not start. Serial No 8U2359

$ 5,500

Cat 2 Ton 1926 Model basically complete, as we found it on a SA

Farm. Serial No 72526

$ 3,000

LeTourneau Dozer. One of proto type and only one ever built. Has 3-

cylinder GM motor, 4 speed gear box, cable blade. Has done very little

work. Ex-Army

$ 10,000


31 May 2020


ENGINE

ALL PRICES ARE SUBJECT TO GST B 615 MODEL OIL BATH AIR CLEANER 1 215 B615, B75, B73 air cleaner top inlet oil bath type 13-inch

330mm diam, 4 1/2 ins 115mm inlet & 4 ins 100mm outlet.

Used

$ 600.00

B MODEL OIL BATH AIR CLEANER 2 217 B Model Air cleaner oil bath (top inlet) MOST LATER Aust B

Models had this type - complete inlet 4 1/2 inches (115mm) outlet

4inches (100mm) - no brackets - diameter - 12 inches (300mm) -

used. Note: Top not included. 217

$ 350.00

B MODEL OIL BATH SIDE ENTRY 3 218 B Model early Air cleaner oil bath (side inlet) (it seems many

earlier

had this but not as common and no air vent) – used

218

$ 455.00

4 219 B Model Air cleaner support bracket oil bath type - 2 required -

price per each - used - suit 2 219 $ 35.00

REPLACEMENT DRY AIR CLEANER - B MODEL 5 150 B Model look alike Air cleaner paper elements dry type -

replacement for oil bath - suits B Model (clamps are separate) -

bolts on in place of original - new - 12-inch (300mm) diam, 4 1/2

ins (115mm) inlet, 4 1/4 ins (107mm) outlet. 150

$ 630.00

ELEMENT FOR PART No 5 Restriction Service Filter XLP18-2035

Scheduled Service Filter SMP18-1035 POA

AIR CLEANER CLAMP 6 Dry element adaptor clamps – sold per each suit part 5 $ 45.00

7 292 Air cleaner top original type hat - NEW. Fit most 4 1/2

pipe applications - Black. 292 $ 190.00

AIR CLEANER ENGINE ENTRY SOCKET 8 204 RH air cleaner pipe entry socket - suit B75 & 73 with longer

bonnet. Not original fitting on standard B 61 type model. This

fitting bolts to firewall and bonnet corner is cut to close over it.

$ 120.00

B MODEL INLET PIPE 9 Air cleaner pipe - fit inside cabin on standard on most RHD B

Model. Connects to air cleaner pipe - made from fibreglass -

used.

$ 150.00

CAB AIR CLEANER ENTRY 10 B cab air cleaner entry flange

Out of Stock

AIR CLEANER SUPPORT BRACKET & BASES 11 B Model RH Standard Air Cleaner - bolt on support bracket only,

bolts to cabin with hole for air vent, later type air cleaner bolts to this

bracket with 2 support brackets - 219 used

$ 120.00

LH ENTRY AIR CLEANER BRACKET KIT 11A Profile cut out sections only to make LH air cleaner bracket

B MODEL BONNET PARTS

31 May 2020


ENGI

NE

ALL PRICES ARE SUBJECT TO GST ENGINE - Luberfiner Element 12 1007 Luberfiner By Pass Oil Filter - length 373mm x 200 diam- NEW -

Fits most B Models. $ 85.00

13 1008 Luberfiner Oil Filter - length 380mm (15 inches) 190mm (7 1/2

inches)

diameter. Suit later model like 675 engine.

$ 120.00

ENGINE MOUNTING INSULATORS See Rubber Parts Section part no 2260 for mounting and other

options.

ENGINE ALLOY WATER PARTS 14 67 711 Oil cooler water outlet (bolts to end of oil cooler) - used

Note: There are square & angle ends. $ 250.00

15 68 711 Cooler oil assembly (water outlet not included) - used $ 110.00

16 69 711 Top water pipe elbow outlet goose neck connects head

mounted water outlet to radiator - there is also a short type -

NEW

POA

17 82 711 Oil cooler elbow bolts onto 67 some have a top outlet - USED $ 110.00

18 213 711 Head mounted water manifold outlet - front. Bolts to head.

Has large opening for gooseneck and thermostat - 500mm long

- USED

$ 180.00

19 222 711 Head mounted water manifold outlet - rear, bolts to head. -

Note:

there are 2 lengths. - USED

$ 120.00

TOP RADIATOR CAP - SUIT B MODEL 20 407 Radiator sealing cap. $ 25.00

RADIATOR

CAP

21 383 Suit most B models including 615. See Part No 3767 for Price

and

Options

ENGINE THERMOSTAT 22 Engine thermostat used. Mack part no 657GC 225A P2 $ 85.00

THERMOSTAT SHUTTER CONTROL 23 135 Radiator Shutter Control Thermostat (sends signal to the air

actuator to open) - NEW $ 218.40

24 170 Radiator Shutter Control Thermostat (sends signal to the air

actuator to open) - used. $ 100.00


31 May 2020


B MODEL CHASSIS

ALL PRICES ARE SUBJECT TO GST RADIATOR SHUTTER CONTROL 25 272 Radiator Shutter control air ram actuator assembly - USED. See

Rubber

Section Part No. 2207 for replacement piston seal.

$ 165.00

26 325 Radiator shutter air ram actuator replacement $ 133.00

B MODEL CHROME HUB CAPS 27 2201 Mack B chrome new front axle chrome hubcaps. Fits FA 505 axle

or

2203 adaptor plates. Size ID 9 inches (228mm) (price per each) –

NEW. LIMITED STOCK AVAILABLE

$ 250.00

ADAPTER FOR B MODEL HUB CAPS 28 2203 Aluminium solid cast adaptors machined & drilled (to fit stock

27 hubcaps t o heavier axle which has flat caps) may also be

used to fit caps to some rear axles-sold per each.

$ 100.00

TIE

RODS

29 402 Tie Rod FA522

B Mack tie rod, suit FA 505. Lighter capacity has hubcaps.

Screw in male thread. 1Kg Each.

RH 1 1/8 x 12 TPI - NEW - PER

EACH LH 1 1/8 x 16 TPI - NEW -

PER EACH

$ 159.00

$ 159.00

$ 159.00

30 403 B Mack tie rod, suit FA 508, FA 517. Larger capacity, has flat

end caps screw - female thread ends L or R. But have new

bushes fitted. Shaft size 1 1/8-inch, One fine, One course

thread. EXCHANGE ONLY. $100 DEPOSIT PER EACH.

PRICE PER EACH.

$ 225.00

32 405 B Mack tie rod super heavy front axle not common in Australia,

Has female threads and 1 1/2 shaft. - USED. Lower yard. $ 185.00

BATTERY

BOX

1455 See Electrical Section part no 1455 for Battery box and other

Battery

Box options

B MODEL GREASE CAPS 36 123 Domed (not common) type suit FA 522 axle with pressed Mack

logo - used - sold per each. $ 59.00

37 312 Axle oil caps front flat steel original t y p e with pressed Mack logo

FA522 axle - used $ 45.00

AXLE

SHAFT

38 126 Axle suit 44000lbs bogey diff with 2 splined ends. Note: There

are two splined types - one has pointed and one has flat tops and

there is a long and a short - Used. (Photo shows single or light

weight drive type)

$ 120.00

FRONT SPRING INSULATOR Front spring insulator. See Part No 2441. Suit B61 and most other

B

models.


31 May 2020


B MODEL CHASSIS ALL PRICES ARE SUBJECT TO GST REAR OF FRONT SPRING PIN 40 Spring anchor pin 1 1/2 x 3 inch 1 7/8 OD. Sold Per Side.

Photo shows bush. $ 100.00

41 73A Bush for above 1 1/2 ID. SOLD PER EACH. Photo shows pin. $ 85.00

ELEPHANT

FEET

SEE RUBBER SECTION FOR SPRING Part No 2444 for

OTHER OPTIONS

B MODEL GEAR BOX PTO 49 85 PTO Assembly with pump to suit adaptor below $ 273.00

B MODEL GEAR BOX PTO 50 83 Gear Ext ra deep adapter (Note: there are two types with power

auto No

GA303 & GA328 that has a trust washer. The face of the plate

to the tip of the gear is 4 inches.

$ 225.00

BELT

DRIVE

52 386 Power Steering pump -Belt drive $ 250.00

DRIVE COUPLING 53 137 Rubber Drive coupling for power steering pump of

Generator (as above). $ 150.00

POWER STEERING PUMP V8 54 365 Power Steering pump with drive - suit 864 V8 - Used $ 500.00

PITMAN

ARM

55 327 B Model Pitman arm for B61 - used $ 45.00

SHOCK ABSORBER - FRONT 56 317 Mack B Rod. 300mm (12 inch) long with 75mm of 9/16 UNF

thread each end - used. No Stock $ 54.00

57 318 Mack B Ball Joint Only, 83MM (3 1/4 INCH) 9/16 Threads each

end - used. No Stock $ 14.00

58 58

Mack B Front shock absorber lower bracket - bolts under spring -

RH

small - used.

$ 36.00

59 220

Mack B Front Shock Absorber with arm type LH. USED $ 54.00

60 321 Mack B Front Shock Absorber with arm type RH - used. No Stock $ 54.00


31 May 2020


B MODEL CHASSIS ALL PRICES ARE SUBJECT TO GST SHOCK ABSORBER - FRONT 61 Mack B Front shock absorber lower bracket - bolts under spring

- LH LARGE - used. $ 36.00

BUM

PER

62 21 B Model black steel extended bumper bar includes top

plate (no mounting brackets) - new $ 1,245.00

63 B Model new stainless- s t e e l extended bumper. Bar includes top

plate

(no mounting in brackets) - NEW

$ 2,100.00

64 B Model Bumper Extended Brackets - used - PRICE PER SET -

(Set

15Kg)

$ 230.00

TOW HOOKS - ORIGINAL B MODEL 65 281 Tow Hooks (bumper bar) L & R sold per each - used $ 135.00

TOW HOOK SPECIAL BOLTS 66 247 Bolts - zinc plated - extra-long for tow hooks 7/8 x 9T x 8 inch

Long - 2

Per Truck - new. Price per each.

$ 9.00

CHASSIS CROSS MEMBER 67 B Model Arched Cross Member - Good Condition $ 227.00

STARTER VALVE & LEVER 68 341 Starter Valve control lever to suit 342 only with new knob - B

Model $ 131.00

AIR TANK BRACKET 69 Air starter valve only - B Model - fits under cabin floor held by U

bolts. $ 182.00

75 Air tank holding bracket, also used on B Mack round fuel tanks.

Price

Per Each

$ 110.00

FUEL TANK

CAPS

262 SEE CAST SECTION - PART 1172 FOR FUEL CAPS AND

OTHER CAST OPTIONS


31 May 2020


B MODEL BONNET ALL PRICES SUBJECT TO GST HOOD/BONNET TRIM STRIPS 76 34 B Model stainless bonnet (hood) trim strips. Set of 6 (one set per

truck -

2 long, 2 short) with set of stainless trim special holding

clips - new. See tube in corner for long strips. Seems to suit

NR as well.

$ 600.00

BONNET TRIM STRIPS 77 12 B Model long stainless hood trim strips (2 per truck) - used -

sold per each. $ 100.00

78 13 B Model short stainless hood trim strips (4 per truck) - used -

sold per each. $ 70.00

79 34 Clips to hold stainless trim strips (14 per truck) - See Catches,

Locks & Clips Part No 829 for details.

HOOD/BONNET HINGE ONLY 80 B Model Stainless steel hood centre hinge cover - runs full length

of bonnet - new - one piece. (clips not included). Suits all models.

Just cut to length.

$ 500.00

HINGE

CLIPS

81 24 B Model hood hinge end cap & strap kit (holds centre hinge part

no

80). Price per set, two end pieces - new.

$ 180.00

AFTER MARKET CENTRE REPAIR KIT 82 378 B Model replacement hood channel for spot welding to existing

bonnet -

2 pieces. Used to make special bonnets or repairs. Sold as a pair.

NEW. Note: centre hinge is for photo only.

$ 100.00

HOOD HINGE HOLDING BOLTS SEE CATCHES, LOCKS & CLIPS SECION PART No 731

FOR OTHER OPTIONS.

B MODEL – HOOD/BONNET MODEL NUMBERS

8 SEE CAST SECTION PART No 1099 FOR MODEL BADGES

AND OTHER MODEL OPTIONS

B MODEL MACK HALF DOG SEE BULLDOG SECTION PART No 665 FOR HALF DOG

AND OTHER DOG OPTIONS

B MODEL MACK CHROME SCRIPT SEE CAST SECTION PART No 1103 FOR MACK SIDE

AND OTHER MACK SIDE OPTIONS

MOUNT KIT HALF DOG & MACK SCRIPT SEE CATCHES, LOCKS & CLIPS SECION PART No 910

FOR MOUNTINGS AND OTHER OPTIONS. $ 5.50


31 May 2020


B MODEL BONNET ALL PRICES SUBJECT TO GST THERMODYNE SCRIPT BADGE WITH

MOUNTING PINS TO SUIT ORIGINAL HOLES IN

BONNET (HOOD).

SEE CAST PARTS SECTION PART No 1123 FOR BADGES

AND OTHER SIDE OPTIONS

DIESEL

BADGES

SEE CAST PARTS SECTION PART No 1125 FOR BADGES

AND OTHER SIDE OPTIONS

US

E

D

91 Diesel script badge - used (some pitting) - (price per each) Subject

to

Stock.

$ 55.00

CURVED B61 TYPE DOG BASES MOUNTING -

STEEL

CO

WL

SEE BULLDOG SECTION PART No 633 FOR DOG BASE

AND OTHER OPTIONS

BULL DOGS - LONG EARS & TAIL 1932 TO 1979 SEE BULLDOG SECTION PART No 630 FOR BULLDOGS

AND OTHER DOG OPTIONS

MACK GRILLE EMBLEM NAME

PLATES -

Fits B61 & similar 460 long 50

high

SEE GRILLE EMBLEMS - SECTION PART No 1096

FOR EMBLEM AND OTHER OPTIONS.

OVAL

EMBLEM

104 Mack oval enamelled grille emblem. Suit B81 type trucks. $ 165.00

RADIATOR CAP 105 B615-73-75-81 Radiator hinged cap - used but rechromed. $ 236.60

BAIL CLIP FOR RADIATOR CAP 106 227 B Model Bail Clip to hold above radiator cap 30 closed - new $ 45.50

107 B Model bail clip to suit 344 - used. $ 28.20

GRILLE & RADIATOR SHELL - SUIT B61 &

SIMILAR

MODEL

TYPES

108 3 B Model pressed steel Radiator Shell for B61 Style Truck -

used. Repair and chrome plate - extra $525.00

$1400.00


31 May 2020


B MODEL BONNET

ALL PRICES SUBJECT TO GST

B615 RADIATOR PANEL ASSEMBLY 109 Top & bottom radiator tanks, side panels & headlight panels cast

from aluminium with louvres (with radiator) - suit B73 - 75 & 615

& other models. Limited Stock

$ 2,730.00

SHUTTER & LOUVRES 110 Radiator shutter louvres Kyser automatic - suit B61 and similar

models - no controls - Used $ 375.00

CAB BRACING BRACKET 111 Cab bracket for radiator bracing rods. L&R are the same. 2

required used per each. $ 35.00

CENTRE

CLAMP

112 Clamp - centre radiator tie rod - pair - used - $ 35.00

BONNET (HOOD) WOVEN LACING SEE RUBBER PARTS SECTION - PART No 2135 FOR

BONNET LACING OPTIONS

T CLIPS FOR HOOD LACING SEE CATCHES, LOCKS & CLIPS SECTION PART No 825

FOR LACING & ALL OTHER OPTIONS

HOOD/BONNET HINGE & CAPS SETS 115 B Model original bonnet star wheel hood (bonnet) Prop RHS &

LHS - Used - Sold separately. Note: has some minor rust

SEE CATCHES, LOCKS & CLIPS SECTION PART No 850 FOR

OTHER NEW OPTIONS

$ 20.00

EXCHANGE ROUND BONNET LATCHES 116 B Model Reconditioned old style round hood latch & with

catch rechromed with new spring & rubber bumper with

chrome cap each change over service only.

SEE R MODEL SECTION PART No 4167 FOR ALL OTHER

LATCH OPTIONS.

$ 210.00

BONNET LATCH SPRINGS Replacement springs for round bonnet latch, also suitable for

square latches. 80mm long x 13mm wide. See Part No 950 for

cost.

FRONT MUDGUARD (Fender) 118 142 B Model mudguard LH or RH $ 750.00

MUDGUARD INNER PANEL 120 282 B Mack inner mudguard s p l a s h panel LH or RH. Used. No Stock

of

RH.

$ 250.00


31 May 2020


B MODEL BONNET ALL PRICES SUBJECT TO GST MUDGUARD INNER PANEL 121 289 Removal fender service panel B61 & similar L&R- used - price per

each

- USED

$ 220.00

BUMP STOPS FOR INNER PANEL 2811 SEE RUBBER SECTION PART No 2163 FOR BUMP STOP

AND OTHER OPTIONS.

B MODEL QUICK TURN PANEL SCREWS 123 2918 Quick turn panel screws with 10 cent coin slotted heads. 20mm

diam head with 20mm quick turn shank. See Part 126 for holding

washers. Price per Each. 4 Per Side.

$ 20.00

125 2593 J Clips for fender (mudguard) panel screws (Suit Part No 123) -

4 per side - price per each. $ 4.00

126 2919 Retainer washers hold removable fender (mudguard) screws in

place when panel is off vehicle. (suit Part No 123) 4 Per Side.

Price per each.

$ 3.00

MUDGUARD INNER PANEL 128 290 Headlight panel B61 & similar. Per each - $ 199.00

HEAD LIGHT PANEL 129 77 B Model Headlight panel - suit B73 & B75 & 615 & similar -

cast aluminium - USED POA

HEADLIGHT PANEL INNER 130 283 Inner head light panel assembly L&R - Used - suit B61 above . &

similar $ 46.00

HEAD LIGHT -DOMED LENS SEE ELECTRICAL SECTION PART No 1575 FOR LIGHT

AND OTHER HEADLIGHT OPTIONS

SEE ELECTRICAL SECTION PART No 1583 FOR GASKET

AND OTHER OPTIONS

HEAD LIGHT BUCKET 133 232 Head light bucket only mounts into panel - used $ 15.00

HEADLIGHT BASE 134 233 Headlight base mounts into headlight bucket - used $ 15.00

BEZEL - B MODEL HEADLIGHTS 136 Parking light lens bezel only - Used $ 150.00

SEE ELECTRICAL SECTION PART No 1581 FOR BEZEL

AND OTHER OPTIONS


31 May 2020


B MODEL BONNET ALL PRICES SUBJECT TO GST HEADLIGHT PANEL SCREWS SEE CATCHES, LOCKS & CLIPS SECTION PART No 916

FOR NUTS AND OTHER OPTIONS

HEAD LIGHT PANEL MOULDING SEE RUBBER SECTION PART No 2388 FOR ALL

OTHER OPTIONS

B MODEL - PARKING LIGHT - WHITE

(ACRYLIC

LENS) –

NEW

SEE ELECTRICAL SECTION PART No 1630 FOR PARK

LIGHTS AND OTHER OPTIONS

B MODEL PARK LIGHT – USED 144 230 Chrome original outer parking light cover with original WHITE

glass lens - Limited Stock - used. $ 55.00

B MODEL PARK LIGHT – USED 145 119 Chrome original outer parking light cover - no glass lens - Limited

Stock - used. Add $20 each for rechroming. $ 40.00

ROUND BLINKER - AMBER LED SEE ELECTRICAL SECTION PART No 1410 FOR BLINKER

AND OTHER BLINKER OPTIONS $ 90.00


31 May 2020


B MODEL CABIN INTERIOR PARTS

ALL PRICES SUBJECT TO GST ASHTR

AY

151 295 B Model original ash tray - complete - Used. No Stock $ 91.00

THROTTLE - (ACCELERATOR) SEE R MODEL SECTION PART No 4404 FOR ALL OTHER

PEDAL OPTIONS

B & R CLUTCH PEDAL RUBBER

SEE RUBBER SECTION PART No 2205 FOR PEDAL AND

OTHER OPTIONS

CONVERSION PLATE TO TAKE MODERN

TREDDLE VALVE

155 581 B Model brake foot (treadle) valve conversion plate only to bolt

into original floor plate to give new bolt pattern. Suitable for use as

single or double circuit brake system. See Brake Section for treadle

valve part no

450. Pedal assembly mounting part 452 curved pedal part no 156

(below)

as used on RHD only.

$ 79.00

FOOT VALVE CURVED PEDAL 156 New RHD Curved brake pedal with Mack logo. Only fit late

pedal adapter. Casting only, not drilled or detailed. NEW. $ 75.00

DIMMER (DIPPER) - DIPPER SWITCH -

TOP FLOOR MOUNTED.

SEE ELECTRICAL SECTION PART No 1495 FOR DIPPER

AND OTHER OPTIONS

DOOR & IGNITION LOCK SET SEE ELECTRICAL SECTION PART No 1610 - CATCHES,

LOCKS & CLIPS Part No 780 FOR OTHER LOCK OPTIONS

KNOBS -

Dash

SEE ELECTRICAL SECTION PART No 1626 FOR KNOBS &

OTHER OPTIONS

BLINKER (TURN SIGNAL) INDICATOR SEE ELECTRICAL SECTION PART No 1435 FOR ALL

OTHER SWITCH OPTIONS.

SPEEDO

CABLE

SEE R MODEL PARTS SECTION PART No 1429 FOR CABLE

AND OTHER TACHO CABLE OPTIONS

B MODEL DRIVER COAT HOOK 168 334 B Model driver coat hook. Price Per Each. $ 16.00

B MODEL INTERIOR PARTS

31 May 2020


B MODEL CABIN INTERIOR PARTS ALL PRICES SUBJECT TO GST CABIN LINING KIT 169 50 B61 Headliner (original style) made to look original trimmed in

tan vinyl - new. Colour and Pattern options are available.

1000X700X500

5kG.

$ 60.00

CABIN REAR LINING 170 25 B61 Cab back cover kit (original style), fits below rear

window - trimmed in tan vinyl in 2 sections - new. (Photos

shows each side)

$ 145.00

FIREWALL MAT INSULATION 171 49 B Model Firewall insulation under dash down to floor mat, cover

with heavy insulation on the back for noise & heat-original type

RH drive model with clutch pocket- new

$ 345.00

SPECIAL INTERIOR INFILL 172 Optional Extra infill rear of cab panels. Fit below rear window

and at very bottom. Not standard but for better finish. $ 100.00

DEFROSTER DUCT 173 B Model Defroster duct plate bolts on top of dash L&R are the

same - price per each. No Stock $ 35.00

DASH

CABLES

176 Original engine stop cable used. Cable broken. Suitable for fitting

new cable to keep original look - used. Limited Stock $ 70.00

177 B Model Twist & lock throttle cable- original knob used. Note: 42

& 43 are used and may require new cable but have the correct

knobs to give dash original look - used. Limited Stock.

$ 70.00

DASH

PANEL

178 74 Dash panel - second hand (no gauges) - may have extra holes. -

USED……… $ 140.00

DASH HOLDING SCREW SEE CATCHES, LOCKS & CLIPS SECTION PART No 725

FOR OTHER OPTIONS

GAU

GES

SEE ELECTRICAL SECTION PART No 1535 FOR DASH

GAUGE OPTIONS.

GLOVE

BOX

179 75 Glove box door - second-hand - no hinge or catch $ 170.00

180 61 Cardboard type glove box liner pocket - original style - new $ 95.00


31 May 2020


B MODEL CABIN INTERIOR PARTS ALL PRICES SUBJECT TO GST GLOVE BOX LOCK SEE CATCHES LOCK & CLIPS SECTION PART No 853

FOR OPTIONS

182 Glove Box Catch for door latch - used. POA

GLOVE BOX HINGES 183 257 Glove Box hinges - L & R - sold per each. NEW. Note: You would

need to change one as we only have one side. $ 85.00

185 Glove box support frame - fits behind at the top and holds the lock

catch. $ 55.00

GLOVE BOX BRACKET 186 250 Side bracket support for hinges L&R - price per each. USED $ 49.00

HORN

BUTTONS

187 58 B Model original horn button with Mack logo - Limited Stock -

Used. SEE PART No 208 FOR OPTION. $ 133.00

SUNVISOR BRACKET 189 347 B Model RH sunvisor bracket detailed. NOT DRILLED

OR DETAILED. $ 49.00

B MODEL SEATS- NEW 190 241 B Model RH standard driver seat - squab and rear cushion - 2

sections. New seat includes new timber base and upholstery with

dog logo using original springs. PRICE PER SET

$ 500.00

191 B Model LH standard seat - squab and rear cushion - 2 sections -

New seat includes new timber base and upholstery with dog logo

using original springs. PRICE PER SET.

$ 550.00

SEAT

FRAME

192 242 B Model RH driver seat frame complete with forward and back

adjusters

- used - as original. No Stock

$ 250.00

193 243 B Model LH passenger set frame - used - as original $ 135.00

SEAT

BRACKETS

194 332 Bracket driver seat cushion - up & down bolts to seat at front

underneath to give two locations for height at front of seat, they are

L&R.

$ 28.00

195 T bolt with rubber washer, holds rear of passenger seat to frame at

top. $ 15.00

196 Bracket driver seat cushion - up & down bolts to seat at front

underneath to give two locations for height at front of seat, they are

L&R.

$ 35.00


31 May 2020


B MODEL CABIN INTERIOR PARTS ALL PRICES SUBJECT TO GST DRIVER SEAT ADJUSTER 197 35 Driver seat adjuster slider with handle forward and back (pair) -

Used. $ 49.00

FLOOR MATS -MOULDED MACK SEE RUBBER SECTION PART No 2301 FOR MAT AND

OTHER CAB MAT OPTIONS

STEERING

WHEEL

201 B Model second-hand steering wheel - original, some cracks not

RW. Check spline diam 22 inch - used. There are 2 similar sizes

with spline American trucks, one is 15/16 & one is 1 inch. The

smaller spline will interchange with many new models.

$ 250.00

AIR

HORNS

SEE DRESS UP PARTS....PART No 1245 FOR OPTIONS


31 May 2020


B MODEL CABIN EXTERIOR PARTS

ALL PRICES SUBJECT TO GST SEE RUBBER SECTION PART No 2193 FOR

MOUNTING AND OTHER OPTIONS

CURVED BASE ROOF MARKER SEE ELECTRICAL SECTION PART No 1474 FOR OTHER

LIGHT OPTIONS

REAR CAB MOUNTING BOLTS 203 200mm x 15mm Rear Cab Holding Bolts. $ 9.00

WINDSHIELD GLASS 204 81 B model windshield (windscreen) laminated auto glass Australian

Standard Stamped, - left and right are the same. 2 per truck - sold

per each

- new.

$ 155.00

REAR WINDOW GLASS 205 84 Rear cab (window) toughened glass. B standard cabins only - new $ 146.00

B MODEL ORIGINAL ENTRY HANDLE 206 47 B Model stainless chrome original pressed cab grab handle as

above - New. Price Per Each. $ 65.00

207 B Model stainless steel original pressed cab grab handle price

per each - original type - used $ 45.00

HORN

BUTTON

208 B Model horn button centre without Mack logo - just a replacement

centre

- new. Note: photo with shows Mack ID plate centre.

$ 110.00

SUNVISOR EXTERNAL - USA LUND STYLE - B 209 207 B model fibreglass exterior sun visor (Lund style). Hardware not

included, as it screws direct onto cabin, may require minor

trimming to fit - new.

$ 500.00

SUNVISOR EXTERNAL STEEL B 210 277 Sun visor steel. Original steel Australian style with mounting kit.

Sun visor centre bracket. $ 550.00

REPLACEMENT WIPER BLADE 211 175 Replacement B Model wiper blade - 2 required - sold per each -

new.

300mm long with hole for holding screws.

$ 40.00

WIPER ARM OPTIONS 212 169 Original painted steel wiper arm - 2 required - sold per each -

used, may have some rust. $ 50.00

213 Wiper arm original style - black - sold per each. New. $ 220.00

214 397 Wiper arm - stainless steel, fit ok but has kink at end and

inbuilt windscreen washers. Would need some modification.

NEW Price per each.

$ 180.00

B MODEL EXTERIOR PARTS

31 May 2020


B MODEL CABIN EXTERIOR PARTS ALL PRICES SUBJECT TO GST WIPER SHAFT WITH MOUNTING 215 Pivot arm assembly bolts to 216 and drive motor $ 45.00

AIR OPERATED WIPER DRIVE 216 Air wiper drive motor (under dash - pre 1960) - used. SUBJECT

TO STOCK. See Part No 4798, may be able to fit. We can also

give contact for repair options.

$ 150.00

WIPER CONTROL VALVE 217 Wiper control valve (4 ports with bleeder) - used $ 120.00

WIPER SHAFT WITH MOUNTING 218 182 Pivot arm under dash with blade drives (bolts through cabin)

see end shelves. $ 32.00

WIPER CONTROL VALVE KNOB 219 183 Dash mounted wiper control knob only. No Stock. See Par No

4816 for maybe option. $ 50.00

WIPER ARM MOUNTING NUTS & SPACER 220 Tapped spacer - NEW - 2 required - sold per each. See Cast Parts

No.

1010 for options

WIPER ARM MOUNTING NUTS & SPACER 221 177 Acorn domed retainer cap nut wiper arm assembly - new - 2

required - sold per each (Not SAE thread). $ 10.00

222 178 Knurled drive tapper spline on OD rectangular hole centre

adapter wiper arm - new - 2 required - sold per each. $ 10.00

WIPER ARM MOUNTING NUTS & SPACER 223 60 Nut holds wiper drive to cabin - fits over chrome tapped spacer (not

SAE

thread) S/S reproductions. - 2 required. Sold per each.

$ 35.00

B MODEL EXTERIOR PARTS

31 May 2020


B MODEL DOOR PARTS

ALL PRICES SUBJECT TO GST

REBUILT

DOORS NEW

DOOR SKIN

224 B Model Left or right-hand door shell (your old door with new

skin etc) This includes full door up to lower window opening

including lower mirror mounting area. Top part of door will be

replaced as required. All parts will be grit blasted and light

undercoat before shipment. Note - door will be as per original if

cabin has been damaged, we may need cabin for correct fitting.

WORK

CHARGE

D PER

HOUR.

USED INNER DOOR PANEL 225 346 B Model Door Inner Panel - no fittings Left or Right - Used

$

160.00

B MODEL DOOR HINGES 226 B Model Door hinge - top one has lug & spring - price per each -

used $

100.00

WINDOW STOPPER 227 336 Door cover plate with window glass stopper. No Stock $

30.00

DOOR HINGE COVER PLATE 228 278 B Model door hinge cover plate - bolt on door to cover hinge.

Bolts (4 required) not standard on all models -used - sold per each

NO STOCK

$

19.00

DOOR WINDOW TRIM 229 B Model Inner window glass surround trim. Fits around top of

door. Left or Right - Used. No Stock $

160.00

QUARTER VENT WINDOW - RECONDITIONED 230 B Model quarter vent window reconditioned and rechromed with

new rubber door seal (part 2501)., New post seal 2504. L&R

exchange service. Price per each. EXCHANGE ONLY - $300

DEPOSIT.

$

850.00

VE

NT

See Rubber Section Part No 2501 for quarter vent window options.

DOOR

GLASS

231 80 B Model Door side toughened auto glass bevelled edge top -

Australian Standard Stamped - left & right are the same. 3Kg

each, Sold per each - NEW

$

150.00

QUARTER VENT GLASS 232 120 B Model Quarter vent window toughened 6mm auto glass - glass

only bevelled edge. Australian Standard Stamped. NEW - PRICE

PER EACH

$

125.00

B MODEL DOOR PARTS

31 May 2020


B MODEL DOOR PARTS ALL PRICES SUBJECT TO GST

NEW ENTRY HANDLE EXCHANGE 233 B Model door exterior new entry turn handle & base plate - new.

Handle - cast from brass with rechromed backing plate. We must

have exchange handle. To get base plate and spring etc. Note: A

deposit of

$70 each will be charged if no exchange.

$ 260.00

SEE R PARTS SECTION PART No 5007 FOR HANDLE

AND OTHER OPTIONS

SEE R PARTS SECTION PART No 5009 FOR HANDLES

AND OTHER OPTIONS

DOOR HANDLE ESCUTCHEON SEE CATCHES, LOCKS SECTION PART No 775 FOR DOOR

AND OTHER OPTIONS

DOOR WINDOW - REGULATOR SCISSORS - NEW 89 SEE R PARTS SECTION PART No 5055 FOR REGULATOR

AND OTHER OPTIONS

DOOR WINDOW REGULATOR & GEAR PLATE -

NEW

SEE R MODEL PARTS SECTION PART No 5057 & 5058

FOR REGULATION AND OTHER NEW OPTIONS

DOOR GLASS CHANNEL SUPPORT - NEW

SEE PARTS Nos 5020 & 5021 FOR OTHER OPTIONS

REPLACEMENT STRICKER PLATE SEE CATCHES, LOCKS SECTION PART NO 1058 FOR

ALL OTHER STRICKER OPTIONS

DOOR STRIKER PLATE 249 95 Left hand striker plate (mounts on cab) - used. No Stock. $ 80.00

250 90 Right hand striker plate (mounts on cab) - used. No Stock $ 80.00

CHROME PLATED STRICKER PLATE 251 385 Left or right sticker plate with new catch Part No 1058 detailed

and chrome plated. - Exchange only $50 deposit. $ 160.00

STRIKER PLATE COVER - DOOR 252 324 Door catch striker plate cover, fits over 249 & 250 door catch.

(part of the cabin) $ 25.00

B MODEL DOOR PARTS

31 May 2020


B MODEL DOOR PARTS ALL PRICES SUBJECT TO GST B MODEL DOOR LOCKS 253 310 B Model Door lock cab latch assembly inner fits in door LH -

used. Limited Stock. $ 150.00

254 311 B Model Lock cab latch door assembly inner fits in door RH -

used. Limited Stock. $ 180.00

255 113 B Model control assembly for door lock (remote control handle to

lock

L&R. It’s a flat bar that goes inside door) - used. No Stock. Part

No

1054 can be adapted but would need end changed.

$ 45.00

MIRROR HEAD - BLACK - NEW 256 103 B Model black powder coated mirror head with Mack

inscription - Dimensions as stock 257. Price Per Each $ 120.00

MIRROR STAINLESS STEEL HEAD ONLY - NEW 257 16 B Model Stainless steel Mack mirror head with Mack Inscription

to suit part number 258. (sold per each) - dimensions of casing -

16 1/8 inches (140mm) x 7 5/8 inches (194mm) - washers &

nuts included New -

$ 180.00

MIRROR ARM SET - NEW 258 15 B Model Stainless steel Mack mirror arm SET L&R kit with rolled

top to suit B doors, mirror heads are sold separate from the arms.

New. Limited stock.

$ 1,300.00

MIRROR ARM SET - USED 259 245 B Model steel original black Mack mirror arm kit L & R complete

with mirror heads (pair) some minor rust needs repainting - used $ 420.00

B MODEL DOOR PARTS

31 May 2020


SECTION 1 - AXLE, HUB, CHASSIS ALL PRICES ARE SUBJECT TO GST

THE HISTORY OF TYPES OF USA STUD WHEELS

There are two types of wheels - "Stud" pilot which use the nuts to centre the wheels, not common in Australia

but on some imported vintage trucks. Today most are "Hub" pilot which uses the hub to centre the wheels. 150

patterns on the same old-style Bud wheels. Some have a large stud and a thin nut and some have small stud

and a large nut.

Early aluminium wheels had 5 slots. The story goes P.I.E. (Pacific Intermountain Express) had Alcoa make these wheels in the fifties as weight saving when tubeless was unheard of. The first Alcoa tubeless wheels

started 1956 with a new design in 1963 and changed from 5 holes to 10. Tyres lasted better, less flats, easier

repairs

HISTORY OF SPIDER TUBELESS STEEL RIMS

With the change from 10.00 - 20-inch tube tyres they became 22.5 and 10.00 22 inch became 24.5 in

tubeless and the 24-inch tube tyre do not have a tubeless replacement. Tubeless rims first started to go on

the Australian market in early 1970's. There are 3 standard sizes,7.5 inches wide x 22.5 inches diameter.

8.25 inches wide x 22.5 inches diameter. This is the best size for the 11R.22-5 tyre. The third is the offset

type rim 9 inches wide x 22.5inches diameter. This rim is suitable for chroming for use on the steer axle. I

purchased the first new truck with tubeless rims in 1976 and went from 4 to 6 punctures per week to zero

EARLY STUD PILOT (IMPORTED EARLY USA

TRUCKS)

266 2124 Early type stud pilot inner sleeves. Note: Left & right threads. Have

2" of thread on sleeve. PER EACH. $ 7.00

267 2125 Early type stud pilot outer nuts. Note: Left & right threads.

PRICE PER EACH. $ 5.00

268 2126 Early type stud pilot inner wh eel sleeves. Note: Left & Right

threads 30mm (1 1/2 of thread). Suit steel wheels. PRICE

PER EACH

$ 8.00

269 2127 Nut for above 266 & 268. PRICE PER EACH $ 4.00

LATE HUB PILOT AXLE, STUDS & NUTS (suit modern hubs) 270 2121 Late type hub pilot axle studs 22mm diam 1.5 thread. Note: length

and shank size can vary with different types of hubs and wheels. -

PRICE P E R EACH

$ 18.00

271 2121 Late type hub pilot axle nuts. PRICE PER EACH. $ 5.00

273 Rear Mack wheel clamps. Length of wedge overall 2.12

inches, width 2.55 inches. Hole size 0.88. (Mack No.

15QJ223PP5)

$ 15.00

R MODEL REAR WHEEL CLAMPS R MODEL FRONT WHEEL CLAMPS 274 Front wheel clamp $ 30.00

AXLE, HUB, CHASSIS

31 May 2020


SECTION 1 - AXLE, HUB, CHASSIS

ALL PRICES ARE SUBJECT TO GST SPIDER WHEEL NUTS 275 2128 Standard Spider wheel rear wheel nut - 3/4 thread. 0.750 in ID

1.25-inch OD. $ 1.15

AXLE COLLET 276 165 Axle collet 1/2-inch Suit B Model. $ 2.00

B MODEL WHEEL & CLEATS

277 Front Wheel Cleats – Photos shows light axle cleats that have hub

caps. Price per each - used. As Photos. $ 36.00

278 Rear axle steel cleats – Price per each - used $ 40.50

TORQUE ROD BUSHING 281 2960 Torque rod bushing press in type. OD 76mm bush Tap er length

59mm bolt diam 38.5mm thread 1.25 x 12 UNF. Suit Mack

camel back suspension. PRICE PER EACH

$ 220.00

282 2961 Torque rod bushing press in type. OD of bush 76mm bolt hole

centre 111mm bolt hole diam 17mm. Also known as an

Equidistant Pin. Suit Mack Camel Back Suspension. PRICE PER

EACH

2961

$ 220.00

CENTRE BEARING 284 2452 R Bearing 1060mm Top to Bottom 240mm. $ 927.00

CENTRE BOLT 286 2952 Centre bolt 12 inches (300mm) long. 1/2-inch diam, 9 inches

of thread. Suit Mack Camel Back and many other jobs. SOLD

PER EACH 2952

$ 23.00

Sold Per Wheel. 289 2954 Brake dust shield suit 38000lbs diffs. Sold per Wheel in 2 Sections.

Note: the same bolt pattern as 290 but has different off set of 15mm

(deeper).

$ 70.00

290 2955 Brake dust shield suit 44000lbs diffs. Larger of set of 35mm.

Sold per Wheel in 2 Sections $ 75.00

PTO COVER 291 Small opening PTO cover 6 1/4 x 5 inch $ 30.00

LARGE PTO COVER

292 Large PTO cover 9 1/2 x 7 3/8.

AXLE, HUB, CHASSIS

31 May 2020


BRAKES

ALL PRICES ARE SUBJECT TO GST BRAKE AIR

TANKS

399 637 Air Tank - 200mm diam x 480mm long $ 160.00

400 638 Air Tank 580mm long 250mm diam. Lug bolt holes apart

680mm. $ 198.00

AIR TANK HOLDING CABLE 401 Air tank holding cable. 890 overall length.

BRAKE CHAMBER FRONT AXLE 402 650 Type 20 Brake Chamber Assembly - B Model. $ 35.00

SERVICE & SPRING BRAKE CHAMBER

TYPE

404 651 Bolt direct onto B Model backing plate lugs 24/24 PRICE PER

EACH. $ 70.00

406 652 Spring brake assembly 30/30. Suit R Model and most trucks.

Note: will only fit B Mack with adaptor plate. $ 50.00

BRAKE DIAPHRAM 414 Type 12 OR 16 Replaceable diaphragm. Suit B Model

- FRONT. Type 20 Replaceable diaphragm R Model. $ 9.00

$ 10.00

BRAKE

CLEVIS

419 Clevis Brake. $ 25.00

420 Clevis Brake

SPRING BRAKE OPTION VALVES 425 584 Spring brake dash control valve lever type with slide lock $ 135.00

SPRING BRAKE ID PLATE 426 Spring brake ID plate. Up Down Lever. Type with lock

replacement face. $ 45.00

427 585 Spring brake dash control valve -pull type $ 140.00

SECTION 2 - BRAKES

31 May 2020


BRAKES (CONT) ALL PRICES ARE SUBJECT TO GST BRAKE CONTROL VALVES DASH

VALV

E

430 586 Valve dash control. Note: Knob part 433 & 434 etc and holding

nut 331 is extra. (see options of knobs) Reference 3 & 4 in R model

brake schematic chart label. See Section Information Labels, Part

No 2730.

$ 75.00

N

U

T

431 587 Nut to hold tractor protection valve. Suit part 430 $ 9.00

LO

CK

PI

N

432 588 Locking pin for valve knob. Suit part 430 $ 3.00

KNOBS AVAILABLE FOR VALVE 330 ROUND ALL BLACK

WITH WHITE WRITING. PARKING BRAKE, AUXILIARY

BRAKE. SYSTEM EMERGENCY CONTROL, WITH

DIAMOND SHAPE WITH YELLOW DOT PARKING BRAKE

(PULL TO APPLY, PUSH TO RELEASE).

SPRING BRAKE KNOB 433 590 Knob only tractor protection. Suit 430 $ 29.00

RESERVE AIR KNOB 434 589 Black reserve knob 38mm diam top. Suit 430 $ 36.00

TRAILER EMERGENCY BRAKE KNOB 435 593 Trailer Emergency Brake Knob Reference 4 in R

Model Brake

Schematic Chart - Section Information Labels Part No 2730.

$ 17.00

SUSPENSION DUMP 436 594 Suspension Dump Knob $ 17.00

SPRING

BRAKE

437 Spring Brake Knob $ 25.00

EARLY TYPE AIR ON/OFF UNIVERSAL

VALVE

440 583 Air simple slide control valve. Suit most early trucks. See

following usage description plates. Can be supplied with other

truck make logos.

$ 48.00

TRUCK VALVE ID CONTROL SEE SECTION INFORMATION LABELS - PART No 2720

FOR ALL OTHER OPTIONS $ 35.00

SECTION 2 - BRAKES

31 May 2020


BRAKES (CONT) ALL PRICES ARE SUBJECT TO GST BRAKE & CLASSIC VALVES TREDDLE OR FOOT VALVE - LATE TYPE 450 579 Brake - treadle or foot valve (only). Suit R Model Mack and B

Model with conversion adaptor plate. See B Mack cab interior

Part No 155 for detail - New. Can be used on single or dual line

brake systems on most USA

trucks. Reference 6 In R Model Brake Schematic Chart Label -

Section

Information Labels Part No 2730.

$ 98.00

TREDDLE OR FOOT VALVE - LATE TYPE 452 580 Pedal assembly suit above foot valve (450). Note: Can only be

purchased with late type pedal (as photo). The curved original B

pedal will fit into this new bracket or for R Model we offer a

pedal with Mack logo (Part no 453 below). Suit E3 & E6 foot

valve. Reference 6A In R Model Brake Schematic Chart Label

- Section Information Labels Part No 2730.

$ 98.00

R MODEL FOOT VALVE PEDAL 453 3074 New brake pedal with Mack logo. Note: holes are not drilled. $ 78.00

TRAILER BRAKE HAND CONTROL VALVE 455 603 Trailer control valve. Reference 9 In R Model Brake Schematic

Chart

Label - Section Information Labels Part No 2730.

$ 191.00

BRAKE. CHASSIS. VALVES TRACTOR PROTECTION VALVE 460 625 Trailer Tractor Protection Valve. Reference 14 In R Model

Brake

Schematic Chart Label - Section Information Labels Part No 2730.

$ 70.00

SERVICE BRAKE RELAY VALVE 462 626 Brake relay valve service brakes. Suit tandem or single axle.

Reference 11

In R Model Brake Schematic Chart Label - Section Information

Labels Part

No 2730.

$ 140.00

SPRING BRAKE RELAY VALVE 463 627 Brake relay valve for spring brake. Reference 12 In R Model

Brake

Schematic Chart Label - Section Information Labels Part No

2730.

$ 109.00

SPRING BRAKE CONTROL VALVE 464 628 Spring Brake control valve. Reference 10 In R Model Brake

Schematic

Chart Label - Section Information Labels Part No 2730.

$ 109.00

DUMP

VALV

E

465 611 Dump quick valve for brakes - 3 port 3/8 NPT ports, used on B

Models and other early type trucks, not used today as they are

noisy. Reference 7 In R Model Brake Schematic Chart Label -

Section Information Labels Part No

2730.

$ 37.00

GOVENOR

VALVE

470 610 Governor valve (air compressor control valve). $ 39.00

AIR TANK NON-RETURN VALVE 472 612 In line non return valve with 1/2 NPTF ports. $ 40.00

SECTION 2 - BRAKES

31 May 2020


BRAKES (CONT) ALL PRICES ARE SUBJECT TO GST DOUBLE CHECK VALVE 473

622

Double check valve 3/8 NPTF 3 ports. Reference 8-20-21 In

R Model

Brake Schematic Chart Label - Section Information Labels Part

No 2730.

$ 40.00

474

623

Double check valve 3/8 NPT 4 ports. Reference 13 In R Model

Brake

Schematic Chart Label - Section Information Labels Part No 2730.

$ 40.00

PRESSURE CONTROL VALVE 475

620

The valve is used to assure a nominal pressure level of 70 PSI. In

the event of a system failure or a decrease in the valves supply

pressure, the valve will prevent further pressure loss or reverse

flow. 1/4 - 18 NPTF ports 60mm long

$ 49.00

AIR TANK DRAIN VALVES 480

492

Drain cock 3/8 thread with 4ft (1220mm) long pull cable. NEW. $ 22.00

DRAIN COCK VALVE 481

490

1/4 BSP with standard quick T bar control, $ 7.00

TAMPER PROOF DRAIN VALVE 482

491

3/8 BSP with hex nut tamper proof control - needs spanner. $ 9.00

AIR PRESSURE RELIEF VALVE 483

499

1/4 BSP. The 106SV Series valve. Comes set a 11 bar

1100KPA/160 PSI

with a plastic tamper proof cap for protection.

$ 19.00

BRAKE

SWITCHES

BRAKE STOP SWITCH Air system brake stop light switch. 1/4 gas thread. SEE

ELECTRICAL SECTION PART NO 1446

BRAKE LOW PRESSURE SWITCH Air system low pressure switch 1/8 gas thread. SEE

ELECTRICAL SECTION PART NO 1445

BRASS BULKHEAD FITTINGS - SUITABLE FOR

FITTING BRAKE LINES THROUGH CHASSIS

& FIREWALL

490 Bulkhead or chassis fitting 1/2" male x 1/2" female - 2 inches

long. $ 19.00

491 Bulk head fitting 1/8 BSP. Female M16 Male $ 10.00

FEMALE BULK HEAD & CHASSIS

FITTINGS

492 Bulk Head - 1/8 - M16 x 1.5. $ 8.00

493 Bulk Head - 1/4 - M20 x 1.5. $ 10.00 494 Bulk Head - 3/8 - M26 x 1.5. $ 11.00 495 Bulk Head - 1/2 - M28 x 1.5. $ 12.00 MANIFOLD ROUND 499 1/4 to 1/4 $ 16.00

SECTION 2 - BRAKES

31 May 2020


BRAKES (CONT) ALL PRICES ARE SUBJECT TO GST MANIFOLD STANDARD 501 3 Port Manifold 3/8 to 1/4 $ 41.00

502 621 5 Port straight manifold 1/4 with end & rear supply entry $ 41.00

SE

ALA

NT

506 636 BondLoc Hydraulic locks and seals, hydraulic and pneumatic

fittings. High pressure resistant. $ 29.00

TRAILER CONNECTOR AIR BRAKE GLADHAND TRAILER BRAKE

COUPLING

510 633 B Model original glad coupling bracket only. Bolts onto rear of

B Model cabin. Fitted to many B Models with T in chassis

number. - Used

$ 20.00

511 As above - available chrome plated NA

BRAKE COUPLINGS 513 607 Trailer brake coupling self-sealing 1/2 NPT female thread

connection. $ 20.00

514 Trailer brake coupling self-sealing 1/2 NTP male thread

connection. $ 20.00

516 608 Trailer brake coupling non sealing adaptor 1/2 NPT female

thread $ 7.00

517 599 Trailer brake coupling, 1/2 NPT male thread $ 7.00

518 600 Trailer brake coupling 3/8 NTP. Male thread. $ 6.00

POGO

STIC

K

520 605 Pogo stick chrome $ 48.00

SU

ZI

CO

IL

523 609 Dual brake suzi coil - short tail. $ 63.00

524 887 Suzi coil 7 core - long tail 3.6m $ 99.00

526 604 Pogo stick Suzie coil clamp hinges to allow placement of hoses

and cable and held in place by steel clasp. $ 21.00

SECTION 2 - BRAKES

31 May 2020


BULLDOGS

ALL PRICES ARE SUBJECT TO GST BULL DOGS - LONG EARS & TAIL 630 Chrome Bulldog hood dog ornament early type with long ears and

tail - USED. 1932 - 1979 - suit all early Mack models including

very early R Model (note: some discolour and/or pitting) - USED.

654

$ 150.00

EARLY LONG EARED DOG

631 New old stock Mack long ear dogs. As fitted to Mack trucks 1932-

1979. $ 230.00

SPECIAL DOG HOLDING SCREWS 632 Special screw in only dog holding anti-theft screws 1 /4 UNFX x

50mm. Bin 631 $ 5.00

DOG BASE - B MODEL 633 Bulldog base - suit B61 and other B model trucks with steel cowl

- NEW $ 250.00

RADIATOR CAP DOG MOUNTING 635 B615-73-75-81 Radiator hinged cap POA

B SPECIAL DOG BASE 638 Dog mounting special base for B 81-85 models etc. Base Only. $ 115.00

LATE MACK DOG (USED AFTER 1979) 640 Late Mack Short Eared chrome Dog. Standard bonnet size...NEW $ 175.00

LATE MACK DOG (AFTER 1979) 641 Late Short eared gold dog. Standard Size – NEW

2516913 FBD5794 377-62 MCK 217BP2

$ 320.00

DOG

BASE

642 R Model base for Bulldog - (suit all big dogs from 1932

to today) chromed with special mounting screws. NEW

FBB 4486

$ 75.00

PROTO TYPE ROUND DOG 643 B Model super proto type round Bull Dog - as developed and

displayed on the early proto type B Model. Same size as

original. Craftsman reproduction cast from solid stainless steel.

NEW

$ 455.00

SMALL BULL DOG - LONG EAR & TAIL 645 Small dog, stand up 100mm early type - Pre 1979 used on

ashtrays and some Mack Jr. Utes. $ 139.00

646 Base for the above dog - tapped so small dog (660) stands on

level base. $ 19.00

Flintstone Front Dog Base25167160 $ 140.00

BULLDOGS

31 May 2020


BULLDOGS ALL PRICES ARE SUBJECT TO GST EH DOG MOUNT 652 1975 EH type short mount grille & dog mount - not finished or chromed $ 91.00

653 1975A E type long radius type grille & dog mount, not finished or

chromed $ 50.00

TYLDEN B MACK JUNIOR RADIATOR MASCOT 661 Tylden B Junior ute radiator mascot & dog base. Special for

TYLDEN fibreglass bonnet. POA

B MODEL MACK HALF DOG 665 B Model half dog emblem - hood sides - left & right - sold per each

- NEW - 2 required $ 135.00

666 B Model half dog - used all have some pitting 98 $ 59.15

B JUNIOR HALF SIZE HALF DOG 667 Special half dog - only half original size, as on our B Junior Ute L

& R. Sold Per Each $ 155.00

R MODEL HALF DOG 668 Mack R - Half Dog - 2 per truck. L&R hand...NEW. Price Per

Each $ 64.00

LATE MACK HALF DOG 670 New Mack logo standing half dog. Left and Right, facing each

other. Cast from brass, detailed and chrome plated as used on

the New Champion older style bonnet conversion. PRICE PER

SET OF 2 DOGS.

$ 180.00

PROFILE SHADOW TYPE DOGS - VINYL 671 Right Hand Shadow Dog Logo. 200mm long. Has sticky on

rear. Suitable for rear window etc. $ 30.00

672 Left hand Shadow dog - 200m long. Has sticky on rear. $ 30.00

SMALL RAISED DOG 675 Mack raised dog cast from aluminium. 200 long, 140 high x

20mm thick. $ 99.00

LARGE RAISED DOG 676 Mack raised dog cast from aluminium with hollow back

section part., 760 long 670 high 65mm thick. $ 400.00

PAINTED OPTION OF 676 677 Mack big dog 760 long 670 high x 65 deep hand air brush painted

- high quality finish then clear coated. Suitable for in or outside

mounting. Weight 8kg.

$ 737.00

BULLDOGS

31 May 2020


CATCHES, LOCKS & CLIPS

ALL PRICES ARE SUBJECT TO GST SPECI

AL

BOLTS

SPECIAL STAINLESS- S T E E L

BOLTS

BUMPER BAR CUP HEAD OR TIMBER BOLTS

685 Bumper bar type domed head 8mm square shank. 5/16x 2 1/2

inch. $ 3.00

686 2893 Bumper Bar type domed head M8 x 30 stainless steel. $ 4.00

687 2895 Bumper bar type domed head M10 x 25 stainless steel. $ 5.00

689 2896 Bumper bar type domed head M10x40 $ 5.00

690 Bumper bar type domed head stainless steel. 30mm x 10mm. $ 7.00

CHE

ESE

HEA

D

699 2936 Raised cheese slotted head 1/4 UNC 1 3/4 long stainless-

s tee l screws. PER EACH. $ 3.00

RADIATOR CAP SCREWS 700 2910 Cast radiator top tank holding S/S screws for (Suit B615, B73-

75-77) 1 1/2 x

3/8. Suit most models with cast radiator. 4 required. Price per

Each. NEW

$ 6.00

DOMED COUNTER SUNK HEAD B MODEL ENTRY HANDLE SCREWS 710 3517 Raised slotted head old time counter sunk S/S screws 1/4 UNC x

1 inch long

304SS. Note: suitable for B Mack door handle holding screws.

(B Model have odbod thread and you need to re tap to 1/4 UNC

to use these screws). Price per each.

$ 3.00

B MODEL DASH SCREWS 715 Counter sunk head screws on dash panel.

COUNTER SUNK FLAT HEAD SCREWS - R MODEL DOOR LATCH 720 3517 Door latch holding screws. 3 per door

FSC 0853 1.61 5/19

$ 2.00

DOMED HEAD SCREWS R MODEL DOOR PANEL & DASH

SCREWS

725

3516

Door panel domed head screws. 20 Required per door. Price Per

Each. $ 4.00

CATCHES, LOCKS CLIPS

31 May 2020


CATCHES, LOCKS & CLIPS ALL PRICES ARE SUBJECT TO GST DOOR REGULATOR SCREWS 728 3341 Screw domed head for regulator assembly above. (6mm) 4

Per Door. Price Per Each. Note: the existing screws are an

odd bod size and you need to tap the regulator for these screws.

$ 2.00

FLAT SLOTTED HEAD COUNTER SUNK

SCREWS

730 Flathead S/S old time slotted head counter sunk 1/4 UNF x 1 1/2

inches long. $ 2.00

B MODEL BONNET HINGE 731 2929 Star counter sunk head S/S B bonnet (hood) hinge end. Holds

down screws. NEW. Supplied with 2 nuts & flat washer Price

per each.

$ 2.00

HEADLIGHT SCREWS B MODEL PAN HEAD 735 2940 Panhead S/S 3/16 x 1 1/2 UNC Headlight. Suit B73-B75,

B615 and other models with aluminium panel. $ 2.00

B MODEL PAN HEAD METAL SCREWS 736 2941 Stainless Screws to hold head light rims 4.2 x 45 long. B43-

B61 etc. Suit B Mack headlight. $ 2.00

NAME PLATE SCREWS 737 Screws for steel Name Plate Mock Corners for fuel tanks to

give rivet type look.

CONVENIENT RIVET - PETERBILT.

KW.

740 2392 Pop type rivet suitable to fill holes in Peterbilt sleepers. Can be

placed from the outside with std pop rivet gun. (Note: hole in

rivet needs to be filled after fitting. Price Per Each. Also used

on some Ford doors.

$ 2.00

QUICK TURN SCREWS B MODEL QUICK TURN PANEL

SCREWS

Quick turn panel screws with 10 cent coin slotted heads. 20mm

diam head with 20mm quick turn shank. See B Model Section

Part No.123 for screws and options.

STAR HEAD SCREWS R MODEL STAR HEAD 749 2922 Star head S/S B model Mack dash. $ 2.00

DOOR LOCK RETAINER CLIPS 755 2912 B & R Model Door lock slide in retainer clip. Slides from

outside of door to hold door lock. Width 30mm length 70mm

hole 22mm, sold per each. Suits other many other models.

$ 13.00

CHAS

SIS

CLIP

S

757 Mack chassis pipe clips $ 6.00


31 May 2020


CATCHES, LOCKS & CLIPS ALL PRICES ARE SUBJECT TO GST DOOR

CLIP - B

& R

760 3540 Retaining ring for regulator to glass support track. Also suit

Ford, Lincoln, Mercury & All Chrysler 41-58. Price Per Each.

(Suit 5055 & 5052). One required for late R per door. Two

required for early type R per door.

$ 4.00

RETAIN

ING

CLIP

765 2920 Door gear plate retaining clip. 1 required per door for B & R

model. Also, all

Chrysler.

FR12814 7/19 2.10

$ 4.00

DOOR HANDLE ESCUTCHEON 775 3526 Handle escutcheon. (Trim ring). Suit door and window crank

handle. $ 12.00

776 3527 Pin Handle window & door. Suit door and window crank handle. $ 2.00

L

O

C

K

S

DOOR T LOCK CATCH 780 715 Door T lock with stainless-s teel sp ring -loaded dust cover.

Rubber seal under stainless steel cup, multiple rod mounts on

locking tongue, stainless steel shaft keyed alike - used mainly

on tool boxes. Suit 80x90 hole.

$ 41.00

FLUSH PADDLE LOCK 781 716 Flush paddle type lock with keys. Suits one or two rods or

cables. 110mm long x 80mm high hole size. $ 41.00

782 714 Flush paddle S/S lock, gasket & keys. Length 82mm x breadth

82mm x depth

33mm. Used mainly on tool boxes & sleepers. Suit hole 60x60

$ 36.00

783 717 Flush Paddle locks with keys - S/S - gasket suit striker plate -

see striker plate for catches hole size 90x65 - used mainly on

tool boxes.

$ 41.00

COMPRESSION LOCK 786 713 Compression lock satin finish & key with adjustable close

position to suit thickness of box 70mmx32mm hole. tank

boxes.

$ 40.95

KEY DOOR LOCKS - B & R MODEL SEE ELECTRICAL SECTION PART No 1610 FOR ALL

OTHER LOCK OPTIONS

PIN TYPE DOOR LOCK 789 733 Pin type door lock suit remote control 15mm adjustable pin type

striker. Door latch is 90mm long x 20mm wide, locating bolt

hole are 70 apart.

$ 41.00

DEC

K

LO

CKS

794 718 Quarter turn latches - vibration resistant die cast - suit

mounting in deck plate up to 8mm - holds down deck drill

20mm hole. 2 types of latch available.

$ 27.00


31 May 2020


CATCHES, LOCKS & CLIPS ALL PRICES ARE SUBJECT TO GST COVE

R FOR

595

795 719 Moulding deck latch lift up lid, chrome plated 28.5mm wide

screw centres

20.6mm. Designed to cover 794 but will need drilling & tapping.

$ 10.00

796 721 Key to open Quarter turn locks 794 $ 5.00

L

O

C

K

S

UNIVERSAL DOOR HANDLE 799 Traditional arched chrome all-purpose universal door handle

with key suit outside door opening - early type trucks and cars

- 130mm long, 56mm high with 125mm long, 8mm shaft.

$ 34.00

MACK DOOR LOCKS 805 1976 Roto-lok it star wheel replacement. Suit Mack trucks 1941-48,

also Chrysler dodge, DeSoto, Plymouth 1939-48, Studebaker

37 & 48, Nash 40-48, Packard 41-48. Suit front right or rear

left door.

$ 55.00 DOOR STRICKER PLATE 810 2261 1 Step striker plate - 56mm (2 1/4 inches) L x 25mm (1 inch)

10mm high 2 mounting holes on each side. Suit flush paddle

locks and some early car and trucks

$ 6.00

811 2263 2 Step striker plate - 238mm (1 1/2inches) 30mm L -

mounting holes on each side $ 6.00

DOOR

DOVE

TAILS

813 2267 Door guide Vee catch to locate door 62mm long 28mm wide,

with 4 holes - suit Mack L cabins but many other early model

trucks and cars - cast from brass. Note: Not drilled as holes

vary with different models - Sold per each

$ 22.00

814

Door Vee guide to locate door 55mm long 26mm wide

18mm high, 34mm hole centre pressed steel Mack Part No

30QS100

804936 39 7/19

803936 39 7/19

$ 55.00

REPLACEMENT STRICKER PLATE 815 New replacement striker plate catch plate cast from

brass. L&R side supplied with stainless bolts. $ 70.00

C CLIPS - SHUTTER 820 2554 Radiator Shutter C Clips - 4mm. Suit B shutter. $ 1.00

821 2555 Radiator Shutter C Clips - 5mm. Suit B shutter. $ 1.00

C

CLIPS -

WIPER

822 Radiator Shutter C Clips. - 6mm. Suit B wiper shaft. 2 required. $ 1.00 T CLIPS FOR HOOD LACING 825 1455 T steel clips for holding hood lacing to the cowling - steel -

28 per B Mack truck, suit other trucks & cars. - sold per set

of 28.

$ 15.00

PER SET

CLIPS FOR B MODEL HOOD TRIM 829 14 Clips to hold stainless trim strips (14 per truck) - sold per each -

new. $ 4.00


31 May 2020


CATCHES, LOCKS & CLIPS ALL PRICES ARE SUBJECT TO GST SPECI

AL

CLIPS

835 1456 Plastic clip for weather strip Sold per each. Suit 6mm hole

and take 5mm pins. $ 1.00

845 1457 Radiator top shield retainer Ford and other blind spot jobs.

Nylon suit 5mm hole 10mm long. $ 1.00

AFTER MARKET LOOK A LIKE STAR WHEEL

HOOD PROPS -

SUITABLE FOR BONNETS, TOOL BOXES & BINS etc

850 726 Bonnet hood star wheel prop 152mm closed, extended 239mm

- NEW - Price per each

851 727 Bonnet hood star wheel prop 285mm closed 470mm, open -

NEW - Price per each $ 47.00

852 728 Bonnet Hood star wheel prop or support stay - 290mm closed -

495mm open with 2 brackets - NEW - Price per each $ 50.00

GLOVE BOX LOCK - SUIT B MODEL

MACK

853 Glove box with lock. (Supplied with keys) $ 95.00

OPEN/CLOSE PUSH LOCK 855 Glove box and small panel universal button push lock. 5/8

thread. $ 43.00

OUTSIDE CAB GRAB ENTRY HANDLE 857 1119 Stainless steel cabin grab handle - cast not exactly original B

Model type but good look alike, same bolt pattern - length 7-

inch (17.77mm) bolt centres. 1

1/2-inch (15mm) x 210mm. - sold per each

$ 28.00

LONG ENTRY GRAB HANDLES 858 1120 Polished Chrome plated brass grab handle 380 long x 25 with

50mm clearance. 3 mounting holes. Note These are available

up to 1200mm long. Suitable cab & sleeper entry or rear of

cabin.

$ 55.00

OFFSET INER DOOR HANDLE 859 Inner chrome offset door pull handle $ 10.00

PIANO HINGE - SUITABLE FOR BONNETS

& LIGHT

TO

OL

BO

XES

.

860 1124 Piano hinge type- stainless steel - to suit new made up bonnets,

tool boxes etc

- 1800x38mm S/S cost per each.

$ 100.00

TYLDEN TYPE B MODEL HINGE

CHANNEL

861 135 Tylden type hinge Channel to suit new made up bonnets -

1500x20x20x20mm - Used with two optional Piano Hinge $ 50.00


31 May 2020


CATCHES, LOCKS & CLIPS ALL PRICES ARE SUBJECT TO GST LASHI

NG

RINGS

870 741 Recessed lashing rings - stainless steel tie down point

anchor. Ute, light trailer. 89x76mm. Price Per Each $ 20.00

871 742 Recessed lashing rings. Zinc plated. This useful steel tie

down is supplied complete with moulded shroud for fixing to

wall or floor. There is a rubber plug to prevent rattle.

Mounting plate 101x95mm OD, Mounting holders

79x73mm - size 7mm. Recess 22mm. SWL 500 kg. Price Per

Each

$ 12.00

INTER COOLER TYPE CLAMP 879 1866 Spring loaded inter cooler stainless-s teel clamp - 5 inch $ 20.00

881 1867 Spring loaded inter cooler stainless-s teel clamp - 6 inch $ 22.00

POSITIVE STAINLESS-STEEL WATER HOSE

CLAMPS

890 1869 Super Clamp 40-43 $ 8.00

891 1870 Super Clamp 43-47 - 1 1/2 inch $ 9.00

892 1871 Super Clamp 59-63 - 2 inch $ 9.00

893 1872 Super Clamp 79-85 - 3 inch $ 12.00

894 1873

Super Clamp 104-112 - 4 inch $ 14.00

BATTERY BOX OR BONNET LATCHES 900 723 B & R model chrome battery box latch, also fits Toyota 40 &

45 series and many other early type bonnets. Foot can be

moved to suit base angle.

$ 35.00

B MODEL MASCOT HOLDING CUPS

910 39 Stainless steel mascot cup washer. 1/4-hole 7/8 diam. 5/16

dish. Price per each. $ 7.00

J TYPE SPEED BODY NUT CLIPS 913 J Nuts - 3.5mm. $ 2.00

915 J Speed nut 5.5mm (7/32

B & R MODEL DOOR TRIM J NUTS

916 2590 J speed nut, holds B & R model steel door trim over edge - 13

per door. $ 2.00

J TYPE BODY NUTS

917 J nuts for steel headlight panel - B model 1/4 (6.5mm)

155AX10 FNN 2555 1.27 050011369

$ 2.00

918 J nuts - 5/16. $ 2.00

CAG

ED

NUT

S

925 Caged Nuts 5/16 $ 1.00

927 Caged Nuts 3/8 $ 1.00


31 May 2020


CATCHES, LOCKS & CLIPS ALL PRICES ARE SUBJECT TO GST WELD ON CAPTIVE NUTS 929 5/16 x 18 weld on captive nuts

HELMET THREAD CUTTING MASCOT

NUTS

930 2580 Helmet speed nut 3/16 - suit B61 23A x 503 $ 1.00

931 2581 Helmet Nuts - size 1/8 Hex 5/16 OD 17/32. Price Per Each. -

suit original

B61 badges for B model - 6 per side.

$ 1.00

HELMET PAL NUTS MACHINE

THREAD

935 2776 Hex Pal nut Size 6/32. $ 1.00

936 2577 Hex Pal nut 8/32. $ 1.00

937 2578 Hex Pal nut 10/32 $ 1.00

D

O

M

E

N

U

T

940 2584 Dome Nut high profile 3/16 - 1/4 - 5/16. PRICE PER EACH $ 2.00

BONNET LATCH SPRINGS 950 161 Replacement springs for round bonnet latch, also suitable for

square latches.

80mm long x 13mm wide. NEW. Price per each.

$ 28.00

UPHOLSTERY HOLDING BUTTONS 960 1454 Trim holding buttons suit 8mm hole. 20mm head. Price Per

Each. $ 2.00

961 3343 Head lining holding buttons. Supplied black but can be painted.

Price Per

Each.

$ 3.00

UPHOLSTERY DOMED BUTTONS 963 Domed trim buttons with push in holding screws. Colour

to match trim supplied or close to a sample.

UNIVERSAL QUARTER VENT HANDLE 970 712 Vent or quarter vent universal turn catch and locating plate L &

R. Price Per

Each.

$ 60.00


31 May 2020


REMANUFACTURED AND

CAST PARTS

ALL PRICES ARE SUBJECT TO GST MACK LETTER SET BLINKER MOUNTING WEDGE (suit B Model) 1010 774 Turn signal spacer wedge on top of front fender to level

blinker light - aluminium - 2 per truck - new. Sold per each. $ 15.00

BLINKER MOUNTING WEDGE (suit R Model) 1011 3262 Blinker mounting spacer wedge - chrome. Cast from brass

and chrome plated. $ 36.00

DIAMOND T PARTS 1013 1755 Cast brass grille curved badge. Curved front grille badge - suit

531

& 630. Size 210x210mm. Not chromed.

$ 135.00

1014 1754 Cast aluminium bumper bar top step to suit model Diamond T

323-

420-520-522-531. Bumper bar top step thread plate as per

original

360long x 160mm wide at large end. Sold as left & right. (per

each) Not drilled.

$ 90.00

1016 1756 Cast aluminium side bonnet badges. Side bonnet badges -

180x100mm. Note: These have been made smaller than original

as we believe originals look too big. Not chromed.

$ 110.00

1017 1757 Cast bronze dash & upholstery badge (fits in plate 1018

below). Small dash plate badge also suitable for door trims.

45x25mm. Not chromed.

$ 45.00

1018 1758 Brass Dash Plate. Round dash plate - 130mm diam. Fits in left

hand hole in dash - Diamond T 323 - 531 models. Stock No

1017 - Diamond badge fits in its centre. Not chromed. See

General Section

$ 45.00

FLOOR MAT EDGE COVER - CAST

ALUMINIUM

1025 1348 B Model cast polished aluminium kick plate with Mack logo to

cover edge of carpet (mat), priced per pair - new B61 type

cabin - not suitable for B73 or B75 without splicing.

B MODEL chrome plated, cast from brass. Allow $250 extra

for brass & chrome.

$ 295.00

CAST PARTS

31 May 2020


REMANUFACTURED and CAST PARTS

ALL PRICES ARE SUBJECT TO GST CUMMINS PLATES - CAST ALUMINIUM 1030 1271 Cummins Diesel cross mounted on raised polished backing with

two mount bolts can have engine model - 190x110 -

NEW...PRICE PER EACH.

$ 98.00

1031 1273 Cummins 290 cast model chrome plate - size 6 1/2x 1 5/8 inches

(165x40mm) - Not finished or chromed. NEW.PRICE PER

EACH

$ 72.00

1032 1275 Cummins 400 cast model chrome plate - size 6 1/2x 1 5/8

inches (165x40mm) - Not finished or chromed. NEW. .

PRICE PER EACH.

$ 72.00

KEITH SIDE BADGE 1037 1365 KEITH side badge 185mm long x 65 high. Nor finished

or chromed. $ 50.00

SPECIAL CAST NAME SCRIPT BADGES 1040 1319 TYLDEN HERITAGE - 30mm high - cast from brass

and chromed. $ 110.00

1041 1320 CUSTOM BUILT -30mm high - cast from brass & chromed. $ 110.00

MODERN TRUCKS MACK HUB 1051 2206 Cast Aluminium front hub caps, designed to fit inside late

American hub with raised Mack logo. SOLD PER EACH $ 200.00

ADAPTER FOR B MODEL HUB CAPS 1052 2203 Aluminium solid cast adaptors machined & drilled (to fit stock

27 hubcaps to heavier axle which has flat caps) may also be used

to fit caps to some rear axles-sold per each.

$ 100.00

DIAMOND T CAST PARTS 1053 1753 Cast Aluminium hub caps. Note: These do not have holding

clips and may not fit on some axle spigots. They do not have

outside lip to allow fitting with external screws. Size 230mm

diameter plus locating lip 80mm deep. Hole ID inside 215mm.

Also available with Mack logo.

$ 300.00

CAST PARTS

31 May 2020


REMANUFACTURED and CAST PARTS ALL PRICES ARE SUBJECT TO GST DOVE

TAILS

1057 1057 Door guide Vee catch to locate door 62mm long 28mm wide,

with

4 holes - suit Mack L cabins but many other early model trucks

and cars - cast from brass. Note: Not drilled as holes vary with

different models - Sold per each. SEE CATCHES LOCKS &

CLIPS PART No 813.

REPLACEMENT STRICKER PLATE New replacement striker plate catch. Plate cast from brass.

L&R side supplied with stainless bolts... SEE CATCHES,

LOCKS & CLIPS PART No 815.

MACK DOOR LOCK Roto-Lokit door. Suit Mack 1941-48. Chrysler, Dodge, DeSoto

1939-48, Plymouth 1940-48, Studebaker 1937-48, Nash 1940-

48, Packard 1941-48, suit right front or rear left. Cast from

brass, not drilled or detailed. SEE CATCHES, LOCKS &

CLIPS PART No

814

KICK PLATES - PROFILED STAINLESS

STEEL

MA

CK

1061 1346 Fuel Tank Entry Kick Plate with Mack logo - suit B square foot

opening - 320x140 profiled from polished stainless steel - per

each

$ 55.00

1062 1347 Running board kick plates with Mack logo - 750x140mm

profiled from stainless steel - suit early truck with long running

boards. NOTE: Other sizes or vehicle brand available on

request.

$ 65.00

MACK AB RADIATOR CAP 1068 AB Mack radiator cap with motor metre mounting hole with

inside thread. Cut. $ 110.00

MODEL

BADGES

MACK JR SERIES 1070 1967 JR round grille badge - 80mm (3 1/8) diameter, not finished

or chromed. $ 60.00

MACK E

SERIES

1072 1741 EH side cigar emblem script plate, Cast from brass not finished

or chromed. Suit E series & similar year models. Price per

each.

$ 85.00

MACK LETTER CASTING 1074 1328 Mack cast brass side oval badge 120 x 60 – suit mounting on

steps,

tool boxes etc. - not finished or chromed

$ 27.00

1075 1325 Mack script cast from aluminium and shaped so when fitted

to a body it looks like a pressing 300mm long 90mm high. $ 90.00

1076 1330 (Mack) J r letters Only. Cast from aluminium and so shaped,

so when fitted to a body it looks like a pressing. Note: photo

shows

1075 (Mack) above this not included in price.

$ 99.00

CAST PARTS

31 May 2020


REMANUFACTURED and CAST PARTS ALL PRICES ARE SUBJECT TO GST TYLDEN MACK JUNIOR 1077 Miniature BJR side badges. (Only half size) Letter 25mm high.

As on our B Junior Ute. Finished and Chromed $ 120.00

MINI MACK LETTERING 1078 Miniature Mack lettering (only half size) as on our B Junior

ute. Finished & Chromed $ 120.00

MINIATURE V8 BADGE 1079 Mini V8 badge. 30mm high. As on our Mack Jr. Suit box lid etc.

CAST RADIATOR BADGES MACK

AB

1080 AB Radiator cap. Machined thread and top. NOT chromed. $ 170.00

MACK JUNIOR 1930S SERIES 1081 JR curved radiator cap surround with Mack name emblem.

75mm

(3 inch) diameter, not finished or chromed but machined.

$ 120.00

1082 JR radiator cap cover & dog base. Small dog part no. 660

mounts in holes. This cover screws on to part no. 1081. $ 172.90

1085 JR hood (bonnet) side cigar type script plate. 380 long x

50mm wide. Not finished or chromed. Price Per Each $ 145.00

TYLDEN B MACK JUNIOR RADIATOR MASCOT

1086 Tylden B Junior ute radiator mascot & dog base. Special

for fibreglass bonnet. Not finished or chromed. $ 99.00

MACK JUNIOR HUB CAP CENTRE 1088 Mack JR hub cap centre. Hex base (85mm wide) 3 1/4 inches

(12mm) thick. Not finished or chromed. $ 60.00

MACK CASTING (CONT) 1090 1326 Mack Aluminium script 115x50 - suit fitting into foot grates etc. $ 37.00

MACK SIDE DOGS 1091 1329 Mack oval raised cast script with dog on top - logo -

48x44mm - extra for chrome plating. Suit axle ends, steering

wheel centres

$ 25.00

1092 1355 Mack oval raised cast script with dog on top, 230 long 150 high

15mm thick. Dog Oval 10mm thick. $ 54.00

CAST PARTS

31 May 2020


REMANUFACTURED and CAST PARTS ALL PRICES ARE SUBJECT TO GST MACK GRILLE EMBLEM NAME

PLATES -

Fits B61 & similar 460 long 50 high

1096 B Model front grille emblem cast from brass detailed

and rechromed. $ 394.00

MACK CHASSIS PLATE - CAST ALUMINIUM 1098 Mack AB type rear cross member name script plate, cast from

aluminium painted green with yellow Mack script cast to look

like the original raised enamel plate - 450x110x6mm

$ 172.90

B MODEL – HOOD/BONNET MODEL NUMBERS 1099 Chrome model hood emblem recast from brass, hand detailed

and chromed. Models available - B20, B42, B47, B57, B60,

B61, B73- B77-B81-B85, B95, B422, B421, B615, B815, H60

- W71.Plated Price Per Each. Bin 8. 8A - 8B - 8C - 8D

$ 155.00

Note: We can make any model number but

a new pattern cost would apply of $60.00

B MODEL MACK CHROME SCRIPT 1103 11 B Model Chrome "Mack" script for Hood Sides - L&R -

NEW - Sold per each $ 185.00

MACK NEW STYLE LATE LETTER SET 1104 New Mack logo letters. Set of 4, cast from brass, detailed

and chrome plated 25mm high. As fitted to new Champion

bonnet. Price per Set of 8 letters - 2 Sets.

$ 280.00

F MODEL BADGE 1105 3326 Mack F700 Badge. Cast from Brass, Detailed & Chromed.

Length

210mm (8 1/4 inch)

$ 200.00

R' MACK MODEL BADGES 1106 3324 Mack R600 badge. Cast from Brass, Detailed & Chromed -

length

210mm (8 1/4 inch)

$ 200.00

1107 3325 Mack R700 Badge, Cast from Brass, Detailed & Chromed.

Length

210mm (8 1/4 inch)

$ 200.00

1108 Mack R800 badge. Cast from brass. Detailed & Chromed.

Length

210mm (8 1/4 inch)

$ 200.00

CAST PARTS

31 May 2020


REMANUFACTURED and CAST PARTS ALL PRICES ARE SUBJECT TO GST V8

EMBLEM

1120 3330 V8 Side Badge. Cast from Brass. Detailed & Chromed.

90mmx60x8 thick. Price Per Each. $ 175.00

THERMODYNE SCRIPT BADGE 1123 36 B Model Thermodyne badge, fully hand detailed and

chromed, fitting pins in bonnet and they are nice and straight

- new - (Price per each)

$ 205.00

DIESEL

BADGE

1125 71 Diesel script badge, cast from solid brass, detailed and

chromed, fitting pins fit holes in original bonnet. Price Per

Each.

$ 130.00

L SERIES MACK BIG DIESEL BADGE 1128 1946 Diesel side badge cast from brass - suit L model. 9" long x 2 1/4

deep. Price Per Each. Suit LF, LJ. LTL, A51, A55, and

Brockway. Detailed & chromed

$ 169.00

LTL/H MODEL BADGES 1131 1940 LTL or LTH BADGES - MADE TO ORDER. PRICE

PER LETTER $ 50.00

MICHELIN

MAN

1133 1375 Cast Bibendum tyre Michelin compressor man on base - 350

high $ 309.00

1134 1378 Cast Bibendum tyre Michelin man 200mm high 140mm

round base. $ 120.00

1135 1377 Cast Bibendum type wall mount Michelin man 460mm high $ 150.00

1136 1376 Solid cast Bibendum tyre Michelin man 240mm high $ 90.00

AMERICAN EAGLE 1138 American wall mounting eagle. 790mm wing span.

NOT PAINTED $ 90.00

BIG BASE MIRROR DOOR BRACKET 1146 1151 2-piece mirror arm bracket mounting set. LTL type. Suit

lots of models & makes. $ 60.00

RADIATOR PARTS 1149 1721 AC Mack top radiator tank, as per original detail &

dimensions - not machined or drilled. $ 3,200.00

CAST PARTS

31 May 2020


REMANUFACTURED and CAST PARTS ALL PRICES ARE SUBJECT TO GST RADIATOR PARTS (CONT) 1150 1722 AC Mack - LH lower tank as per original - not machined or

drilled $ 600.00

1151 1223 AC Mack - RH lower radiator tank as per original detail &

dimensions, Not machined or drilled. $ 600.00

AK MACK PARTS 1154 1700 AK Mack new aluminium top radiator tank - as per original

fitting, not machined & drilled. $ 3,300.00

SAMPLE PHOTO

1155 1701 AK Mack new aluminium LH lower radiator tank - not machined

&

drilled.

$ 620.00

SAMPLE PHOTO

1156 1 AK Mack new aluminium RH lower radiator tank - not machined

&

drilled.

$ 620.00

1157 AK Mack new aluminium hose fitting POA

NO PHOTO AVAILABLE

1158 1703 AK Mack new aluminium hose fitting, not machined & drilled.

Note: AK are larger capacity radiators - check size before

ordering.

POA

NO PHOTO AVAILABLE

AC RADIATOR CAP 1159 Original AC radiator cap mascot. 50mm round badge. $ 87.00

MACK EARLY CAST STEP PLATE 1160 1301 Step plate early Mack logo 280 long x105 high. 10mm deep -

cast from aluminium. Not drilled or detailed. $ 89.00

1161 1302 Mack cast step plate 470mm long x 120mm wide. Not drilled

or detailed. $ 89.00

STEPS - CAST ALUMINIUM FOOT HOLE 1163 1514 Foot hole recessed step -rolled top - face 165mmx140mmx90

deep - foot hole - 115x95x90 deep - aluminium with polished

face

$ 91.90

MACK B - ALUMINIUM 1164 1164 Mack original recessed foot hole step rolled to suit round tank

560mm diameter.180mm wide x 150 deep & 240 high. Note:

Mat finish.

$ 180.00

MACK R - 2 FOOT DIAMETER 1165 1516 Mack original recessed foot hole. Cast aluminium mat

finish. Step suitable radius to suit round tank 610 mm wide

(2ft), step

370mm wide x 130mm deep x350mm high.

$ 335.00

CAST PARTS

31 May 2020


REMANUFACTURED and CAST PARTS ALL PRICES ARE SUBJECT TO GST DIAMOND T STEPS 1168

1759

Cast aluminium step plates. Diamond T step plate mould based

on original rubber step with Diamond cast in centre. 680 long x

220 wide. Not finished or chromed.

$ 180.00

1169

1760

Cast aluminium step plates. Diamond T step plate. The mould

based on original rubber step with Diamond cast in centre. 790

long x 150 wide. Not finished or chromed.

$ 200.00

B MODEL FUEL TANK CAPS - LARGE 1172

262

Brass fuel cap large type with four lugs - Snyder Buffalo cast

from brass & machined with new 100mm thread 130mm Top -

new.

$ 150.00

FUEL TANK CAPS - SMALL 1173

273

Brass fuel cap 55mm thread (2 1/8). Top 70mm (2 5/8)

Snyder - Used. Some B & early R model. $ 45.00

FUEL TANK FILLER 1174

363

Fuel tank filler tube aluminium for welding into tanks to take

large

B (part 1172) filler caps. Note: not machined - new.

$ 50.00

1175

363A

With clean up and new thread for Buffalo cap, Part No. 1172

ready for welding into tank POA

FUEL TANK CAP - R MACK 1177

3022

Fuel Cap - 57mm $ 260.00

1178

3021

Fuel Cap - 115mm $ 200.00

FUEL TANK GASKET 1179

3020

Cork Fuel cap gasket 115mm Suit 1178

X50MB227 8-39 7/19

$ 5.00

UNIVERSAL TANK CAP & SPIGOT 1181

3023

Universal cap and weld in filler tube 45mm hole. Suit oil and

fuel cap. Top 70mm - 2 inches $ 60.00

1182

3024

Universal cap and weld in filler tube 45mm hole. Suit oil and

fuel cap. Top 70mm - 2 1/2 inches $ 60.00

CAST PARTS

31 May 2020


REMANUFACTURED and CAST PARTS ALL PRICES ARE SUBJECT TO GST BRASS UNIVERSAL CAP 1183 3029 Brass universal cap suit fuel, oil and other applications. 2

inches. BSP. $ 60.00

VENTED FUEL CAP (fits R Model) 1184 Fuel Cap Replacement. Vented 4.050-inch thread 4 3/8 inch.

NEW $ 120.00

CHAMBERLA

IN

1188 1361 Front grille plate, cast from brass, not detailed or chromed $ 150.00

1189 1362 Front up and down grille plate, (TYPE DIESEL) cast from

brass, not detailed or chromed $ 140.00

1190 1363 55DA Diesel side badge cast from brass, not detailed or

chromed. $ 150.00

CAST PARTS

31 May 2020


DRESS UP PARTS ALL PARTS SUBJECT TO GST AIR BAG (AIR SPRING) CONVERSION KIT FOR

PASSENGER COMFORT AND DRIVER FATIGUE, AS THE

DRIVER HAS A VEHICLE WITH IMPROVED HANDLING,

BETTER STEERING, GREATER BRAKING ABILITY.

1210 2273 Tylden Heritage now offers load sharing air helper suspension

suitable for insulation on front suspensions for truck chassis and

highway vehicles. Note: Load sharing is intended for use on

primary front suspensions with 3.5 or 4-inch-wide springs. The

base casting must be slightly modified for use on the 3.5-inch

springs, each kit includes 2 air bags, upper and lower mounting

K4 brackets, cab mounted pressure regulator/gauge panel and air

fittings and pipe. Cost is dependent on truck model, size & type of

kit required. PHOTO SHOWS R MACK.

Cost from

$1200.00

R MACK KIT AIR REGULATOR 1212 Air regulator 1/4-inch fitting mounting bracket with 40mm gauge

0 - 150PSI. 0-1000 KPA $ 65.00

AIR SPRING 1213 2273 Firestone Air spring base 7" (180mm) height unloaded, 9 inch

(225mm) top width 61/4 inch (160mm) $ 220.00

LOW PROFILE AIR SPRING 1214 2280 Firestone Air Spring base and bottom 5 1/4 (13mm) height

unloaded 5 3/4 (146mm) $ 420.00

1215

2276

Air helper spring kit - suit Dodge, Ford, GM ute

AIR VENT 1219 1582 polished roof lining air vent cover. Suit B model optional vent $ 50.00

AUSTRALIAN OPTION UNIVERSAL ROOF VENT

1220 Cabin roof lift up solid top air vent - Australian option fits in top

of cabin roof (very effective cooling a must for summer), 180x100

(7x4). Also suitable for inspection or service access doors. Trailer,

canopy, horse float, rally car. See part no 1219 for surround.

$ 73.00

MACK SLEEPER TOP HATCH 1221 1583 As above but outside dimensions - 265x214 - Cut out size

220x170. Fit Australian built fibreglass sleeper. $ 79.00

MACK B JUNIOR TILT FIBREGLASS BONNET 1222 1961 Mini tilting bonnet (hood) for custom utes (pick-up truck) 2.9m

(114 inches) wide to suit standard car parking spaces. Designed to

suit B Mack cabin and Dodge (USA built) chassis but hinge point

can be changed to suit other makes and model chassis. See cover

photo for finished unit.

$ 3,500.00

DRESS UP PARTS

31 May 2020


DRESS UP PARTS ALL PARTS SUBJECT TO GST MACK B JUNIOR TILT FIBREGLASS BONNET 1223 1964 Bonnet Guard extension fits above with mounting rebate on

cabin. For above. (pair) To suit Part No. 1222. $ 340.00

MACK B TILT BONNET OPTION 1224 1963 Fibreglass Maxie tilting bonnet (hood) (B615 look-a-like) suit

fitting to B61 type trucks - to give better access & B615 look. POA

FIBREGLASS REAR MUDGUARDS (FENDERS) 1225 1962 Old style rear mudguard - suit ute (pick-up truck). Designed to

suit 16"to 20" wheels. The guard is 1250mm long 660mm high

at front & 550mm high at rear and 280mm deep, but deeper

options are available for dual wheels.

$ 1,100.00

DUAL WHEEL STEEL TRUCK MUDGUARDS 1230 1949 Steel 1mm wire edges old style dual tyre truck mudguards.

630mm wide 1260mm radius at bottom. Made in Europe. SOLD

PER EACH.

$ 275.00

EXHAUST 1240 979 Pete Exhaust mount grommets P 01-0800003

1241 978 Stainless cab angled bracket Pete STY 01-08000120

8" EXHAUST KIT 1242 982 8 INCH EXHAUST KIT - LIMITED STOCK $ 5,200.00

B MODEL AIR HORN - SHORT 1245 3442 B Model Dual ORIGINAL Grover chrome short trumpet air

horns - original - (per set) with valve & fittings.380mm (15

Inches long) - new. EM 52290 118 7/19

$ 191.10

1246 Air Horn round dual original t r u m p e t PA 1 – Grover Copy –

380mm (15 inches long). Per set- suit R or B - New. $ 176.00

AIR HORN - ROUND LONG 1248 3439 Horn - Air - round single trumpet kit. Suit R model 600mm (24

inches) long $ 145.00

AIR HORN - RECTANGULAR 1250 3440 Mack horn 26inch air rectangular - front with snow cover with

mounting kit. Suit R Mack. $ 240.00

1254 Air Horn - manual control kit - dual. $ 95.00

DRESS UP PARTS

31 May 2020


DRESS UP PARTS ALL PARTS SUBJECT TO GST AIR HORN 1255 487 Air horn pull type control valve $ 25.00

1256 488 Air Horn - manual control kit - single. Valve only $20 each $ 75.00

1257 489 Air Horn - manual control kit - dual. $ 95.00

GEAR STICK KNOB 1260 1127 Black round gear shift knob 44mm diam, no logo. 3/8 unc

thread. $ 25.00

JOEY BOX CATERPILLAR KNOBS 1264 1260 Knobs long (caterpillar type) for Joey box M10-M12 thread.

Thread 1260. $ 23.00

1265 1129R Also available in red with 3 different thread size adaptors.

1129R

CUSTOM LIGHT BAR 1270 2238 Custom profiled steel rear light bar. 2450 long x 210 high x 60

deep x 3mm thick

ADD $ FOR CHROME PLATING

$ 800.00

ARY LIZARD SKIN Lizard skin is a special sound and heat easy spray on cabin

insulation. Developed in the USA for hot rods, RV vehicles and

truck and sleeper, and is applied one on the other, One US gallon

covers approx. 18-22ft. Supplied in 2 US gallon buckets. (7.57

litres).

1275 2386 Sound control designed to reduce unwanted noise. Improves

sound system performance. Per 6.57 litre bucket. 260 height x

250 weighs 11Kg.

$ 300.00

1276 2385 Ceramic insulation designed to decrease engine and solar heat

transfer. Sound and ceramic help also to seal out moisture. Per

7.57 litre bucket. 260x250 weighs 5Kg.

$ 300.00

SOUND INSULATING SHEETS 1277 2389 Heavy duty bitumen- b a s e d panels with poly propylene covering.

Self-adhesive backing. Prevents vibration noises such as drive shaft

tunnel, floor assembly, wheel housing, doors and other side parts.

Resistant to water, high heat resistant. Can be cut to size, painted.

Kit includes 6 panels per box. 550x250x2mm. Kit weight 2.5Kg.

$ 89.00

DRESS UP PARTS

31 May 2020


DRESS UP PARTS ALL PARTS SUBJECT TO GST FORM SHIELD (CABIN INSULATION) 1279 1396 Form shield with silver backing heat and noise insulation -

18mm thick X 1m wide - Price per metre $ 75.00

STEERING WHEEL 1281 3454 Mack optional upgrade. 18 inch 4 spoke steering wheel. $ 286.00

1282 3455 Steering wheel hub for above to suit R model standard steering

shaft.

POA

No

Phot

o STEPS - PULL OUT AND FOLD DOWN 1289 1520 Pull Out & fold down one step - zinc plated - slides under body

for transport 350 wide 400 deep step, drops down. $ 90.00

1290 1521 Pull Out & fold down two step zinc plated, slides under body for

transport - 350 wide, 660 long, step drops down 530mm $ 100.00

1291 1523 Pull Out & fold down three step - zinc plated - slides under body

for transport - 350 wide, 750 long, step drops down 600mm $ 110.00

TANK STRAPPING

Note: photos show end & bolt not included

1295 Stainless steel 38mm wide flat tank straps, 2mm 304 No 8 PVC

mirror finish Laser cut 1800mm long material strap only. PER

EACH (Photos shows connection not included)

POA

1296 1566 Stainless steel 50mm wide flat tank strap 3mm 304 No 8 PVC

mirror finish Laser cut 1800mm long strap only (Photos shows

connection - not included).

$ 40.00

WASHER SPRAY NOZZLE 1297 1094 Chrome universal wiper washer nozzle. Price Per Each $ 40.00

UNITY SPOT LIGHT 1301 Unity spot light bracket kit. POA

DRESS UP PARTS

31 May 2020


ELECTRICAL ALL PARTS ARE SUBJECT TO GST ROUND BLINKER AMBER LENS 1410 769 Fender (mudguard) turn single round face 12V globe type amber

lens, both sides 110mm diameter. Price per Each. See Part 1412

for red lens.

$ 90.00

1411 776 Genuine original signal - stat. Amber both sides. Price Per Each $ 110.00

1412 768 Red for 1410. - suit above - Price Per Each $ 8.00

AMBER

LENS

1413 Amber lens to suit Part No. 1410 $ 16.00

ROUND BLINKER - AMBER LED 1414 772 Fender (mudguard) turn single round face LED 135mm diam

x 60 wide, 100,000-hour LED life 10 to 30-volt DC $ 90.00

R TYPE SQUARE BLINKER 1415 R Type double side square hood blinker lamp included wiring

tail. Size 115x115 lens. Note: This light has a built in side lamp

chrome bezel.

$ 105.00

1416 3331 Square chrome 21 LED 120mmx120mmx55mm round

centre 2 mounting 55mm centres. $ 140.00

CLEARANCE LIGHT 1417 Peterson USA clearance light LED amber red, 9-30V. 65. Sold

with chrome mounting bracket $ 28.00

SUPERLINER STYLED DUAL FACE BLINKER 1421 3341 Combination turn signal, side marker & park light signal with

round lens. USA made, grey body with amber and red main lens.

4 wires. Replaceable globe 12V 2.1A 0.5 Park. Price Per Each.

Or Supplied with 2 Amber lens. Add $32

$ 165.00

SMALL ROUND BLINKER SIDE AMBER 1423 3335 R Model side hood blinker lamp - Amber 90MM DIAMETER.

12v Globe Type. - Price Per Each. Complete assembly with

wires. Also see park lights part No 1630. For clear option.

$ 70.00

BLINKER MOUNTING WEDGE (suit B Model)

774 Turn signal spacer wedge on top of front fender to level blinker

light. See Cast Section Part No 1010 for details

BLINKER WIRING COVER BOOT SEE RUBBER SECTION PART NO. 2359 FOR DETAILS

ELECTRICAL

31 May 2020


ELECTRICAL ALL PARTS ARE SUBJECT TO GST BLINKER (TURN SIGNAL) INDICATOR STALK 1435 775 R Model original chrome handle turn signal column switch.

Mounts on steering column. 8 wire plug. $ 104.00

BLINKER (TURN SIGNAL) INDICATOR 1436 776 R or B original handle type turn column switch - 5 wire plug. $ 130.00

1437 777 R type with high and low dipper switch on stalk with plug for

blinker cannister with 1 metre wiring loom also suit Peterbilt and

many

other options

$ 160.00

BRAKE STOP SWITCH 1445 591 Air system brake stop light switch. 2 wire. 1/4 gas thread. $ 30.00

BRAKE LOW PRESSURE SWITCH 1446 Air system low pressure switch 1 wire, 1/8 gas thread. $ 75.00

LAMP PARK BRAKE COVER 1448 Lamp dash park brake warning light. Red Lens with P in centre. -

No globe. 25x25mm $ 35.00

BATTERY ISOLATION SWITCH 1451 Battery isolation master switch suit car, utility or air starter trucks $ 28.00

HEAVY DUTY BATTERY MASTER SWITCH 1452 Double terminal 250amp master battery isolation switch $ 60.00

BATTERY BOX COMPLETE 1455 3064 Heavy duty Mack battery box base with ribbed top - 2 sections.

New. Note: we can supply lid chrome plated. 16Kg.

L500W400H300

$ 380.00

BASE BATTERY SECTION 1456 3065 Heavy duty Mack type battery box, bottom section holds 2

batteries with rubber latch/catch- as on R model - new. Note: we

can supply chrome catch for B Model original look

$ 290.00

LID

COVER

1457 3066 Black steel ribbed top battery box lid cover - correct for R model -

3

Kg. NEW. Note: we can supply lid chrome plated.

$ 160.00

CHROME OPTION 1458 3069 Disassemble and chrome plate and reassemble battery box lid to

show condition (cost of box lid not included in this cost) $ 370.00

ELECTRICAL

31 May 2020


ELECTRICAL ALL PARTS ARE SUBJECT TO GST CABIN BULLET LIGHTS 1470 3444 Bullet type roof lights 390mm long x 90mm diam, supplied

with mounting bolts. $ 145.00

SHORT CENTRE BULLET LIGHT 1471 3445 Bullet short centre light. 200mm long x 90mm diam. Price Per

Each. $ 135.00

REPLACEMENT LENS 1472 Replacement cabin bullet light lens

FLL 4197 19-40 5/19

$ 30.00

CURVED BASE ROOF MARKER 1474 797 B Model original cab roof marker lights -acrylic lens -set of 5.

see original type. Supplied with wiring, fuse and switch, they

are close to the original.

$200.00

SET OF 5

1475 796 B Model cab roof chrome marker lights with curved base, acrylic

amber lens (5 per truck) sold per each. They are close to the

original. - New - Price per each.

$ 84.00

1476 795 B Model Original glass amber lens to suit 797 marker lights -

used - price per each. Also see Back store. $ 19.00

CAB MARKER LIGHT FLAT BASE 1477 798 Cab marker light flat base 12V globe type 200mm long

with mounting pad.

ROOF LIGHT ORIGINAL MOULDED EDGE

TYPE

RUBBER PAD

SEE RUBBER PARTS SECTION PART No 2190 FOR

DETAILS

CIGARETTE LIGHTER - ORIGINAL TYPE 1490 818 Chrome knob cigarette lighter power plug - suit B Model and

most cars and trucks, (element & dash mounting) - new. $ 48.00

DIMMER (DIPPER) - TOP FLOOR MOUNTED. 1495 B Model old style headlight dimmer switch - floor mounted - suit

B Model & other early model cars & trucks. NEW. NOTE:

Designed to mount on top of floor plate

$ 28.00

DIP SWITCH (BELOW FLOOR TYPE) 1496 914 Mack R Series dip switch with long or short leg. Bolts below

floor. $ 59.00

MEGA

FUSE

1500 3389 Mega fuse block 70mm long $ 7.00

WEDGE TYPE FUSEHOLDER 1501 6 wedge type fuse holder junction terminal block $ 14.00

ELECTRICAL

31 May 2020


ELECTRICAL ALL PARTS ARE SUBJECT TO GST STANDARD USA MATCHING GAUGES -

BLACK

FACE & BEZEL. SUIT MOST TRUCKS

SPEEDO CABLE TYPE 1515 3367 Speedo gauge. 0-120 kmh cable 3 1/4 diam. $ 210.00

TACHO CABLE TYPE 1516 3369 Tacho gauge. Zero to 3200 RPM with built in hour meter. 3 1/4

inch. $ 230.00

MECHANICAL OIL PRESSURE GAUGE 1517 3372 Oil pressure gauge. 0 - 50 PSI mechanical. Suit 2-inch hole

mounting. $ 130.00

LOW OIL PRESSURE SWITCH 1518 Low oil pressure engine warning switch. $ 51.00

OIL TEMPERATURE GAUGE 1519 3378 Gauge - Oil Temp. Engine, Transmission & Diff. 140 to 360

FH. Neg GND $ 90.00

OIL TEMPERATURE SENDER 1520 3379 Gauge - Oil Temperature Sender for part 1519. Transmission &

Diff. $ 60.00

VOLT

METER

1521 3377 Gauge Volt 12V 10 to 16amps battery condition and charge

section $ 110.00

WATER TEMPERATURE GAUGE 1522 3380 Gauge - Water Temp Neg 100-230 Fahrenheit Electric. $ 105.00

WATER TEMPERATURE SENDER 1523 3381 Gauge - Water Temperature Sender Unit. Negative Ground.

Sender for part 1522. $ 55.00

ELECTRICAL

31 May 2020


ELECTRICAL ALL PARTS ARE SUBJECT TO GST AIR PRESSURE GUAGE SINGLE NEEDLE 1524 Air pressure gauge single needle 0 to 150 $ 100.00

AIR PRESSURE GAUGE DUAL NEEDLE 1525 Air pressure gauge - black face, black bezel, green & red needles.2

1/8 dash hole. $ 150.00

FUEL

GAUGE

1526 Fuel Gauge. See part No. 1527 for sender

FGG0500 135 7/19

$ 95.00

UNIVERSAL TYPE USA TYPE FUEL GAUGE

SENDER

1527 3388 Sender Fuel Gauge. B, R & F multi volt. Suit tank 6-24 inch deep.

Suit Pal & Mack gauges. 250 ohm empty 102 ohm half full &

31ohm full. For Stewart Warner, Datcon, Fara, Medallion &

Teleflex gauges. Supplied with instructions. Would suit most

USA built trucks.

FSU 0528 56 7/19

$ 85.00

FUEL TANK LEVEL GAUGE GASKET 1528 Cork Gauge Replacement Gasket to suit 1526. Note: Gasket

supplied with new gauge. $ 7.00

OPTIONAL UNIVERSAL PYROMETER KIT 1529 Pyrometer kit - suit 2 1/8 dash cut out, black face and bezel.

Kit includes long cable and manifold sender assembly. Suit

E7

CHR/CLR MHR V8 Etc.

$ 395.00

LOW WATER PROBE 1530 Low water sender unit radiator. Suit E6 & E9 and most

applications. $ 98.00

LIGHT SOCKET KIT 1531 12V light socket for gauge illumination to suit gauges in this

section. See 1563 for pricing.

ELECTRICAL

31 May 2020


ELECTRICAL ALL PARTS ARE SUBJECT TO GST CUSTOM BUILT GAUGE KIT...... MADE IN USA 1535 3386 Custom gauges with chrome bezel, black or white faces, older

type needles with Mack and dog logos on speedo & taco. Sold as

set of 7 gauges. Kit includes speedo, transducer & fuel level

sender & instructions.

$ 3,000.00

GAUGES - MACK SPEEDO SUPPLIED 1540 3155 Speedo head cable operated with in built dipper light 0-120Km.

85mm hole size $ 250.00

TACHOGRA

PH

1541 3156 Tacho head 0-32--RPM cable operated with black bezel inbuilt

hour meter. 85mm hole size $ 250.00

1542 1030 Tacho - Black face with Mack logo Chrome bezel 0-32-- RPM

with engine hours cable operated chrome bezel. Suit 85mm dia

hole. New old stock

$ 250.00

ENGINE OIL PRESSURE MECHANICAL 1543 3157 Oil Pressure Gauge 0-150 mechanical operation. $ 155.00

ENGINE OIL TEMPERATURE ELECTRICAL 1544 3158 Oil Temperature- engine, transmission, diff 1 and 2. As the

temperature of your engine, gearbox and diffs, oils increase under

heavy load if run above normal temperature for a long time. There

is a danger that the oil may become so thin that it can no longer

lubricate the moving parts properly.

$ 135.00

SEND

ER

1545 3379 Sender transmitter engine, gearbox & diffs, OIL. Suit 3158. 10-15. $ 132.00

VOLT

METER

1546 3159 Volt Meter $ 150.00

ENGINE WATER TEMPERATURE

ELECTRICAL

1547 Water Temperature Gauge 40 to 120. Suit 53mm hole. $ 150.00

WATER TEMPERATURE SENDER 1548 Sender transmitter engine, WATER Temperature. Suit 1547. $ 99.00

AIR PRESSURE DUAL NEEDLE MECHANICAL 1549 3161 Air Pressure - Dual Needle, dual pipes $ 155.00

ELECTRICAL

31 May 2020


ELECTRICAL ALL PARTS ARE SUBJECT TO GST FUEL

GAUGE

1550 3163 Fuel Gauge - Neg grounding. Suit 53mm hole. $ 140.00

EXHAUST PYROMETER 1551 3104 Excessive temperature is the greatest damaging factor to an

engine. Pyrometer 0 to 700c. Suit 55mm hole. Drivers can use

pyrometers to diagnose engine problems and drive more

efficiently prolonging engine life and reduced fuel consumption.

$ 305.00

PYROMETER TRANSMITTER 1552 3165 Transmitter Pyrometer probe (Thermocouple) inserted into the

exhaust manifold. On V type engines twin pyrometers can be

installed allowing left and right comparison of exhaust

temperatures to diagnose engine problems.

$ 170.00

BOO

ST

1553 3170 Boost gauge is a pressure gauge that indicates manifold pressure

of turbo charger. A boost gauge is expressly important if boost

pressure is being modified to levels higher than OEM Standard.

ELECTRICAL

31 May 2020


ELECTRICAL ALL PARTS ARE SUBJECT TO GST SPEEDO CABLE TYPE WITH

AUSTRALIAN CHROME

BEZEL

1555 Speedo gauge 0-120kmh, cable operation black face chrome bezel.

3

1/4-inch diam

$ 290.00

TACHOMETER MECHANICAL CHROME

BEZEL

1556 Tachometer 0-35--RPM black face chrome bezel 3 3/8in hole $ 310.00

MECHANICAL OIL CHROME BEZEL 1557 Engine Oil Pressure Mechanical black face chrome bezel. 2 1/8

hole.

FGG 0528 457/19

$ 218.00

AMP METRE CHROME BEZEL 1558 Amp bezel + or - 100 black face chrome bezel 2 1/8 dash hole. $ 218.00

VOLT METRE CHROME BEZEL 1559 12 Volt metre 10 to 16 black face chrome bezel. 2 1/8 dash hole.

FGG 0563 58 7/19

$ 218.00

MECHANICAL WATER TEMPERATURE

CHROME BEZEL

1560 Water temperature gauge, black face chrome bezel mechanical

tube

6ft (1830mm) of tube 1/2 BSP connection. 2 1/8 dash hole. Mack

part no 3MT246. FGG 0514 62 7/19

$ 200.00

MECHANICAL AIR PRESSURE CHROME

BEZEL

1561 Air pressure gauge, single needle - to 150 black face, chrome

bezel. 2

1/4 dash hole.

$ 200.00

FUEL GAUGE CHROME BEZEL 1562 Fuel gauge black face, chrome bezel 2 1/8 dash

hole. SEE Part No 1527 for tank sender. $ 180.00

ELECTRICAL

31 May 2020


ELECTRICAL ALL PARTS ARE SUBJECT TO GST GAUGE

OPTIONS

AIR PRESSURE KIT 1565 3371 Oil and Air line and fitting kit. 2m PVC tubing and gauge

adapter. Note: air gauge has 2 connections $ 45.00

OPTIONAL FITTINGS FOR GAUGES 1566 3366 12V light socket for gauge illumination. Price per Each. $ 11.00

1567 1053 Plug for light socket connection gauge. Price Per Each. $ 2.00

VDO GAUGE PLUGS 1568 1054 Plug for VDO gauges, speedo and Tacho. 8 Pin. PRICE PER

EACH $ 17.00

VDO SPEEDO TRANSDUCER 1569 VDO Speedo Transducer - Special price

340.808 9316842109155 $ 125.00

HEAD LIGHT -DOMED LENS 1575 936 New Headlamp Assembly. Fits most Mack’s with single round

7-inch headlight and other trucks and cars, has domed lens.

Supplied with lens body and lead and gadget ready for fitting. Ex

USA

$ 150.00

HALOGEN HEADLAMP 1576 937 Halogen headlamp assembly 7" with bowl $ 150.00

1577 935 New 7-inch head lamp assemble with gasket but no light lens. $ 60.00

ELECTRICAL

31 May 2020


ELECTRICAL ALL PARTS ARE SUBJECT TO GST CHROME BEZEL OPTIONS 1581 3317 Chrome head light bezel. Suits steel style fronts, R also DM,

Valueliner and Flintstone & B80 & 81 Tylden JR ute. Size

rear ID

210mm front ID. 185mmx30mm deep. Sold Per each.

$ 103.00

HOLDING

RING

1582 3320 Sealed Beam 7 inch holding ring. Holds lens in its mounting body. $ 30.00

GASK

ET

1583 Headlamp Gasket for 1575 light assembly. $ 11.00

HEADLIGHT ASSEMBLY 1588 3338 Complete oblong head light assembly RH (see part no 31593

for chrome bezel) $ 235.00

1589 3339 Complete oblong head light assembly LH. (see part no 1593

for chrome bezel) $ 235.00

HEADLIGHT BEZEL - SUPERLINER 1593 3332 Duel headlight bezel. Suit Superliner. 1 3/4 (45mm) deep

with mounting screws. PRICE PER EACH $ 110.00

MACK

SUPPLY

1594 3333 Dual headlight bezel Mack Supply. Suit Superliner. 1 3/8 (35mm)

deep with mounting screws PRICE PER EACH $ 140.00

HEADLIGHT RELAY 1595 Relay for headlights twin.

DOOR & IGNITION LOCK SET 1610 856 Door & ignition lock set includes 2 door tumblers and one

ignition tumbler with 2 matching keys. Length 4 7/8 inch.

Suit Mack B & R and lots of other makes and models cars

and trucks.

$ 85.00

IGNITION SWITCH 1611 855 Two position ignition switch with 2 keys, Suit 3/4-inch dash

hole. Made in the USA by Cole Hersee. $ 45.00

B MODEL LARGE HOLE

1612 857 As Above but suit 1inch dash hole. Mack No MR3172P2.

Suit B Mack, International. Made in USA. $ 45.00

HYST

ER

1613 858 Hyster Fork Lift Ignition lift 24mm

ELECTRICAL

31 May 2020


ELECTRICAL ALL PARTS ARE SUBJECT TO GST INTERIOR LIGHT - UNIVERSAL - GLOBE TYPE 1619 896 Old style interior 5-inch domed lens old style single pole. 12V

globe. $ 20.00

INTERIOR LIGHT 1620 3364 R Model dome interior light with switch and lead. Suit R & B

Model. $ 91.00

B CAB MARKER SWITCH 1625 905 Cab marker On/Off Switch $ 10.00

KNOBS -

Dash

1626 910 Black knobs with white (marker light engraved into knob) 3/16

UNF

thread for 905 - New.

$ 8.00

SWITCHES - HEADLIGHT 1627 B Model Original Style Push Pull head light switch with fuse

- 2 positions - black knob headlight symbol, NEW. $ 25.00

HEADLIGHT SWITCH KIT 1628 Headlight switch with alum knob, shaft, collar, connector

and terminals. Suit 5/8 dash hole with dimmer control. $ 45.00

TOGGLE SWITCH 1629 Toggle switch on-off-on. $ 8.50

PARK LIGHTS ASSEMBLY 1630 3336 Lamp Marker Park Light Complete Assembly with wires -

White. Price Per Each. Complete assembly with wires.

FLS 4276-001 7-32 7/19

$ 60.00

LENS -

AMBER

1631 Parking White or Amber Acrylic lens only - suits 1630. New. $ 20.00

LENS -

WHITE

1632 Parking lens - white acrylic lens only - suit 1630

AMBER REFLECTOR 1635 55mm Diameter Amber Reflector with Adhesive Backing

PARK LIGHT LENS 1640 844 E & L Mack Reproduction Diamond T & White etc park light

lens

ONLY.

$ 40.00

REVERSING LIGHT 1643 4-inch round LED clear reversing light $ 50.00

ELECTRICAL

31 May 2020


ELECTRICAL ALL PARTS ARE SUBJECT TO GST PLUGS ANDERSON 1645 Anderson plugs - general POA

JUNCTION

BOX

1649 Original 6 pin junction block $ 25.00

NUMBER PLATE LIGHT 1651 LED Number plate light $ 25.00

1652 LED dual number plate light. Sold Per Pair. $ 50.00

MACK STARTER SWITCH 1654 917 Cab push starter button black knob chrome nut $ 30.00

HIGH BEAM LIGHT 1660 872 B Model original style high beam or warning light - Red Green

lens. $ 8.20

OLD TIME COTTON TAPE 1670 Old style cotton type insulation tape, (to give your wiring the old

time look) $ 18.00

ELECTRICAL

31 May 2020


DO YOUR OWN FULL SIMPLE UNIVERSAL 12 VOLT EASY TO INSTALL

1. This kit should typically be used in a modified

simple application only, car or truck with front mount

engine with fuse box under dash.

2. This kit and all accessories that connect to this kit

must be rated at 12 volts. 3. This kit supports the use of a high current self

exciting 1 wire alternator or other style internally

regulated alternators. An adapter may be necessary in

some applications.

4. This kit will not support the wiring for amp meter

gauge.

5. This kit does not include, headlight, ignition or

dimmer switches (see Electrical Parts for options)

6. This kit does not include battery cables.

7. There is no set pattern on how the wire is routed.

8. There is more wire than required for circuits.

9. Printed wires will have the same colour coding as on the drawing for easy instillation.

10. Each wire requiring termination is

1675 12 Circuits $ 450.00 1281 NOTE: This is a universal kit and would suit

most 12volt cars & trucks and we use this on

our B and R restorations.

ELECTRICAL

31 May 2020


FITTINGS ALL PRICES ARE SUBJECT TO GST. STANDARD BRASS BSP SCREWED

FITTINGS

(CATEGORY 1)

HEX

PLUG

1701

1993

1993 Brass hexagon head plug - 1/8 NPT. $ 2.00

1702

1994

1994 Brass Hexagon head plug - 1/4 NPT. $ 2.20 1703

1995

1995 Brass hexagon head plug - 3/8 NPT. $ 3.00 1704

1996

1996 Brass Hexagon head plug - 1/2 NPT. $ 3.00 1705

1997

1997 Brass Hexagon head plug - 3/4 NPT. REDUCING BUSHES 1706

2000

2000 Brass reducing bush - 1/8 to 1/4 NPT. $ 1.73

1707

2001

2001 Brass reducing bush - 1/8 to 3/8 NPT $ 3.00 1708

2002

2002 Brass reducing bush - 1/4 to 3/8 NPT $ 3.00 1709

2003

2003 Brass reducing bush - 1/4 to 1/2 NPT. 1710

2004

2004 Brass reducing bush - 1/2 to 1/8. 1711

2005

2005 Brass reducing bush - 1/2 to 1/4. 1712

2005A

2005A Brass reducing bush -3/4 to 1/2. ELBOW M & F COMPACT

1715

2006

2006 Elbow M & F 1/8 $ 3.00 1716

2007

2007 Elbow M&F 1/4 $ 4.00 1717

2008

2008 Elbow M&F 3/8. $ 6.00 1718

2009

2009 Elbow M&F 1/2. $ 9.00 ELBOW 45 DEGREES M & F. 1725

2011

2011 Elbow 45 deg. M&F 1/8. $ 5.00

1726

2012

2012 Elbow 45 deg. M&F 1/4 $ 6.00 1727

2013

2013 Elbow 45 deg. M&F 3/8. $ 9.00 1728

2014

2014 Elbow 45 deg. M&F 1/2 $ 11.00 HEX

SOCKET

1730

2016

2016 Brass Hexagon socket - 1/8 NPT $ 2.00

1731

2017

2017 Brass Hexagon socket - 1/4 NPT. $ 2.00 1732

2018

2018 Brass Hexagon socket - 3/8 NPT $ 3.00 1733

2019

2019 Brass Hexagon socket - 1/2 NPT $ 4.00 1734

2020

2020 Brass Hexagon socket - 3/4 NPT $ 5.00 STANDARD BRASS BSP SCREWED

FITTINGS

(CATEGORY 1)

HEX

NIPPLE

1740

2022

2022 1/8. $ 1.00

1741

2023

2023 1/4. $ 2.00 1742

2024

2024 3/8. $ 3.00 1743

2025

2025 1/2. $ 4.00

FITTINGS

31 May 2020


FITTINGS ALL PRICES ARE SUBJECT TO GST. LONG HEX NIPPLE 1745 2027 1/8 X 2 $ 5.00 1746 2028 1/4 x 2 $ 5.00

1747 2029 3/8 x 2 $ 8.00 M & F LONG ADAPTOR 1749 2051 1/8 to 1 1/2 1750 2052 1/4 to 4.0 REDUCING NIPPLE 1751 2054 1/4 x 1/8 $ 3.00

1752 2055 3/8 x 1/8 $ 4.00 1753 2056 3/8 x 1/4 $ 4.00 1754 2057 1/2 x 1/8 $ 6.00 1755 2058 1/2 x 1/4 $ 6.00 1756 2059 1/2 x 3/8 $ 6.00 REDUCING SOCKET 1760 2032 1/2 X 1/8 $ 7.00

1761 2033 1/2 x 1/4 $ 7.00 1762 2034 1/2 x 3/8 $ 7.00 1763 2035 1/4 x 1/8 $ 7.00 1764 2036 3/8 x 1/2 $ 7.00 1765 2037 3/8 x 1/4 $ 7.00 FEMALE ELBOW 1770 2067 1/8 Elbow.

1771 2068 1/4 Elbow. 1772 2069 3/8 Elbow 1773 2070 1/2 Elbow FEMALE

TEE

1775 2039 1/8. $ 7.00

1776 2040 1/4. $ 8.00 1777 2041 3/8. $ 11.00 1778 2042 1/2. $ 16.00 MALE BRANCH TEE 1780 2043 .1/8 $ 12.00

1781 2044 .1/4 $ 12.00 1782 2045 .3/8 $ 12.00 1783 2046 .1/2 $ 12.00 FEMALE

CROSS

1784 2047 .1/8 $ 10.00

1785 2048 .1/4 $ 12.00 1786 2049 .3/8 $ 20.00 1787 2050 .1/2 $ 22.00 2

0

6

5

HEX LOCK

NUT

1788 2061 Lock nut - 1/8 $ 2.00

1789 2062 Lock nut - 1/4 $ 2.00 1790 2063 Lock nut - $ 2.00 1791 2064 Lock nut - $ 3.00 1792 2065 Lock nut - 3/4 $ 4.00 BRASS SLEEVE 1400 SERIES COMPRESSION 1793 564 Brass Sleeve - 1/4

1794 565 Brass Sleeve - 3/8 $ 1.00 1795 566 Brass Sleeve - 1/2 1796 567 Brass Sleeve - 5/8 $ 3.00

FITTINGS

31 May 2020


FITTINGS ALL PRICES ARE SUBJECT TO GST. BRASS INSERT - 1400 SERIES 1797 571 Brass insert - 1/4

1798 572 Brass insert - 3/8 1799 573 Brass insert - 1/2 1800 574 Brass insert - 5/8 BRASS NUT 1400 SERIES 1801 555 Brass nut - 5/8

1802 556 Brass nut - 3/8 1803 557 Brass nut - 1/2 1804 558 Brass nut - 5/8 MALE CONNECTORS 1805 522 Brass SAE 45 flare male connector 3/8 tube 3/8 NPT $ 4.00

1806 523 Brass SAE 45 flare male connector - 3/8 tube 1/2 NPT $ 6.00 1807 524 Brass SAE 45 flare male connector 1/2 tube 3/4 SAE 1/4 NPT.

1808 252 Brass SAE 45 flare male connector - 3/8 tube 5/8 SAE 3/8 NPT

1809 527 Brass SAE 45 flare male connector - 3/8 tube 5/8 SAE 1/4 NPT

1810 528 Brass SAE 45 flare male connector - 1/2 tube 3/8 NPT BRAKE ELBOW FLARE - 90 Deg 1811 526 Brass 90 deg - SAE 45m Flare 1/2 tube 1/4 NPT. $ 7.00

1812 519 Brass 90 deg SAE 45 flare elbow 1/2 tube 3/8 NPT. $ 6.00 1813 529 Brass 90 deg SAE 45 flare 1/2 tube 1/2 NPT $ 8.00 BRAKE ELBOW FLARE 45 Deg 1814 Brass 45 deg.

BRAKE FEMALE CONNECTOR ADAPTOR

1815 Brass female connector 1/8 to 1/8 NPT BRAKE FEMALE CONNECTOR ADAPTOR 1816 409 Brass female connector 3/16 x 1/8 NPT $ 10.00

BRAKE NYLON TUBE JOINERS 1820 430 1/4 Nylon Tube Joiner $ 5.00

1821 431 3/8 Nylon Tube Joiner $ 6.00 1822 432 1/2 Nylon Tube Joiner $ 10.00 BRAKE MALE CONNECTORS/ADAPTOR 1825 413 Brass male tube connector - 3/16 x 1/8 NPT $ 5.00 1826 414 Brass male tube connector - 1/4 x 1/8 NPT

1827 416 Brass male tube connector - 1/4 x 3/8 NPT $ 5.00 1828 417 Brass male tube connector 3/8 x 1/8 NPT $ 6.00 1829 419 Brass male tube connector 3/8 x 1/4 NPT $ 8.00 1835 422 Brass male connector 3/8 x 3/8 NPT $ 8.00 1836 422A Brass male connector 1/2 tube x 1/4 NPT. 1837 423 Brass Male connector 1/2 tube x 3/8 NPT $ 12.00 1840 425 Brass Male connector 1/2 tube x 1/2 NPT $ 12.00 1841 427 Brass Male connector 1/2 tube x 3/4 NPT $ 16.00

FITTINGS

31 May 2020


FITTINGS

ALL PRICES ARE SUBJECT TO GST. BRAKE MALE BRANCH TEE 1842 435 Brass male branch tee - 3/8 x 3/8 tube x 1/4 NPT.

1843 458 Brass male branch tee - 1/4 x 1/4 x 1/8 NPT. BRAKE MALE RUN TEE 1850 433 Brass Male run tee 1/4 tube to 1/4 NPT.

1851 436 Brass Male run tee 3/8 tube to 1/4 NPT $ 15.00 1852 437 Brass Male run tee 3/8 tube to 3/8 NPT. $ 15.00 1853 454 Brass Male run tee 1/2 to 1/2 $ 18.00 BRAKE ELBOW 90 Deg

CONNECTOR/ADAPTOR

1854 438 Brass elbow 90- deg 1/4 tube x 1/8 NPT. $ 5.00

1855 438A Brass elbow 90 deg 1/4 tube x 1/4 NPT 1856 439 Brass elbow 90 deg 3/8 tube x 3/8 NPT. $ 10.00 1857 440 Brass elbow 90 deg 1/4 tube x 3/8 NPT. $ 6.00 1858 441 Brass elbow 90 deg 3/8 rube x 1/8 NPT $ 7.00 1859 441A Brass elbow 90 deg 1/2 tube x 3/8 NPT 1860 442 Brass elbow 90 deg 3/8 tube x 1/4 NPT $ 9.00 1861 443 Brass elbow 90 deg 1/2 tube x 1/2 NPT $ 10.00 1862 444 Brass elbow 90 deg 1/2 tube x 3/8 NPT BRAKE ELBOW 45 Deg CONNECTOR 1863 448 Brass elbow 45 deg - 1/4 tube 1/8 NPT. $ 10.00

1864 449 Brass elbow 3/8 x 1/4 NPT $ 10.00 BARB

FITTINGS

1865 541 Brass Bar Tee 1/8 $ 10.00

FIELD ATTACHABLE 247 N SERIES 1866 539 Steel NPT male rigid hose fitting - 5/16 ID x 1/4 pipe $ 13.00

1867 540 Steel NPT male rigid hose fitting - 5/16 hose ID 3/8 pipe $ 14.00 FEMALE SWIVEL 1870 548 Steel 1/4 hose. SAE swivel $ 16.00

1871 549 Steel 5/16 hose 1/2 swivel $ 16.00 1872 550 Steel 5/16 hose 5/8 swivel $ 16.00 1873 551 Steel 1/2 Hose 3/4 swivel $ 29.00 1874 553 Steel 7/8 hose 1" Jic Swivel $ 45.00

JIG FEMALE SWIVEL 1880 547 Steel female 45 flare 5/16 hose

Steel female 45 flare 7/8 hose

FITTINGS

31 May 2020


FITTINGS ALL PRICES ARE SUBJECT TO GST. BRAIDED BRAKE HOSE GIVE YOUR RESTORATION THAT PERIOD LOOK

WITH COTTON BRAIDED FABRIC COVERED LOW

PRESSURE HOSE. APPLIATION AIR, FUEL. OIL &

WATER, WORK PRESSURE 350 PSI. TEMP RANGE 40OC

TO 100OC. Sold per metre.

1881 613 Cotton braided air hose - 3/16 4.8

1882 614 Cotton braided air hose - 5/16 working pressure 2250PSI- Price

Per Metre $ 35.00

1883 615 Cotton braided air hose - 1/4

1884 617 Cotton braided air hose - 1/2 Price per Metre $ 38.00

1885 618 Cotton braided air hose - 7/8. Price Per Metre $ 58.00

SINGLE WALL BLACK AIR BRAKE TUBE CATEGORY 14 Description Burst Pre-Pressure Working Press Cost per

Metre

Size PSI KPG PSI KPA

per Mtr

1886 504 1/8 Nylon Brake Tube 1/8 1000 6890 250 1723 $ 2.00

1887 505 3/16 Nylon Brake Tube $ 3.00

1888 506 1/4 Nylon Brake Tube 1/4 1000 6890 250 1723 $ 3.00

1889 507 3/8 Nylon Brake Tube 3/8 1200 8268 300 2067 $ 5.50

1900 508 1/2 Nylon Brake Tube 1/2 800 5512 200 1378 $ 6.00

FITTINGS ALL PRICES ARE SUBJECT TO GST. COLO

UR

1/2 NYLON BRAKE TUBE 1901 509 1/2 Nylon braided air brake tube - RED J844B $ 6.00 1902 510 1/2 nylon braided air brake tube - YELLOW J844B $ 6.00

1903 511 1/2 nylon braided air brake tube - GREEN J844B $ 6.00

1904 512 1/2 Nylon braided air Brake Tube - BLUE J844b $ 6.00

RUBBER LINED HOSE CLAMPS 1920 559 16mm Rubber lined hose clamp $ 1.00

1921 560 19mm Rubber lined hose clamp $ 1.00

1922 561 25mm Rubber lined hose clamp $ 2.00

TEFLON

TUBE

1923 518 1/8 OD X 1/16 Teflon Tube - Price per metre $ 12.00

CLEAR

TUBE

1924 1/4 OD x Clear Tape

FITTINGS

31 May 2020


FITTINGS ALL PRICES ARE SUBJECT TO GST. TA

PS

DRAIN

TAP

1930 493 Drain Tap -or fuel tank 3/8 gas $ 16.00

HEATER

TAP

1940 496 Heater tap 3/8 hose 1/4 gas $ 25.00

1941 497 Heater tap 5/8 hose 3/8 gas $ 28.00

FUEL TANK

TAP

1950 1349 Brass stop tap - new - 1/2 female, 1/2 male, NPT thread with

round gate wheel handle - looks like original - new. PRICE PER

EACH. Bin 1394. See Part no. 522 to 528 for connections.

$ 39.00

TRUCK TANK VALVE 1951 1395 Brass stop tap 3/8 NPT female. 3/8 NPT Male. $ 35.00 TRUCK TANK VALVE FLARE OUTLET 1952 1396 Brass stop tap 1/2 flare x 1/2 NPT $ 36.00

ON/OFF AIR

TAP

1955 Dash mounting type one-way air tap. 1/8 thread Mack No.

20QE39311

FITTINGS

31 May 2020


PARTS BOOKS ALL PRICES SUBJECT TO GST MACK TRUCK SALES BROCHURE PLEASE NOTE: ALL BOOKS ARE PHOTOCOPIES MACK AC SALES BOOK FROM 1927 2001 1715 AC fully detailed specification history book with description and photos of all parts and

photos of different applications including Prime Mover - Tray - Tipper - Vans - Fire

Trucks - Tankers - Buses - Tower Trucks - Two Trucks - 54 Pages.

$ 46.00

MACK A DRIVE HAND BOOK 2005 A Model glove box drive hand book - Suit A50H, A50X, A50T, A50RT, A50S &

A50RST. $ 40.00

2006 1643 A50 & A50T Parts Book - 56 Pages B MODEL SALES BROCHURE 2010 1657 B615 Sale brochure - Or see our website. $ 7.00 2011 END 864 Mack engine sales brochure - or see our website $ 7.00 MACK B DRIVER HAND BOOK 2020 B Model Glove box driver hand book (Petrol & diesel) - 100 pages - has

general maintenance, model info, gear changing & ratios, lubrication, engine

END 673.

$ 30.00

2021 1606 Glove box driver comprehensive information booklet - 212 pages, suit B, H models

cooling system, operative & driving instructions for 15 & 20 speed lubrication, oil types,

preventative maintenance, Thermodyne engines - 48 pages, clutch - 13 pages, gear box 5-

10-15-20 speed -

20 pages, air brakes - 8 pages, rear axle - 47 pages, troubleshooting - 11 pages.

$ 60.00

MACK B CABIN CATALOGUE 2025 612 Cabin parts catalogue - Standard round B Model - CA21 & CA211 as on most trucks in

Australia includes assembly photos on bonnet, mudguards, firewall, floor, dash, cabin,

interior, doors, cab mountings, seats, windscreen, wiper, heater, cowl, mirrors, quarter

vent window, wiper motor - with Mack parts numbers for each item - 98 A4 pages.

$ 80.00

MACK B CABIN ONLY PARTS CATALOGUE 2026 1603 Cabin Parts - B73 & B75, CA30, West Coast round type - details as above (1612) but

has longer bonnet step down in floor, cast radiator. This model not common in

Australia.

$ 80.00

MACK B MODEL PARTS BOOKS B

61

5

2030 1608 Parts Book - B615 RS - 277 Pages - Complete parts book. END 864 V8 engine,

power steering, rotary injector pump, square fuel tanks, cast radiator, two disk clutch,

TRQ 7220

5x4 gear box, centre bearing type tail shaft, heavy front axle, heavy tandem rear axle.

$ 100.00

WORKSHOP

MANUAL

B

61

5

2031 1621 B Model Workshop manual - 486 pages. Comprehensive detail with driving & gear

shifting instructions, lubrication, oils, preventative maintenance, engines END 673-673P-

711-END T

673, END 672-510-864, electrical wiring details, air starter, clutch set up, gear box

quad overgear 5x4, brake trouble shooting, camber & caster, full diff assembly single

axle, glass fitting. B615 heading.

$ 100.00

2032 1610 Service Workshop Manual - B615 -RS - 527 Pages. Table of torque - 8 pages, operation

detail - 15 pages, driving a Mack diesel - 5 pages, lubrication - 22 pages, preventative

maintenance - 37 pages, Engine END864 - 147 pages, cooling system - 25 pages,

electrical with wiring diagrams - 33 pages, clutch - single & double plate - 26 pages,

transmission 9 &

10 speed & TRQ722 quadruplex - 25 pages, tail shaft - 5 pages, brakes - 34 pages,

steering gemmer, ross, power assist with trouble shooting etc - 8 pages, front axle with

sheel

alignment data - 22 pages, rear axle - 16 pages, wheels - 16 pages, springs - 4 pages,

chassis -

8 pages, body - 11 pages, tools - 7 pages

$ 120.00

PARTS BOOKS

31 May 2020


PARTS BOOKS ALL PRICES SUBJECT TO GST PLEASE NOTE: ALL BOOKS ARE PHOTOCOPIES B MACKMACK 2035 1632 Parts Book - Great to help see how the bits fit - suit B61 RS (Note: R - is for right hand

drive

& S is for six wheels) Tandem. - Book is in 2 sections - Section 1 - 275 pages - covers 711

engine & clutch - first 250 pages. 5x4 gear box.

$ 91.00

MACK B WORKSHOP MANUAL 2036 Service Workshop Manual - B61 - 740 Pages $ 130.00

FLINTSTONE 2045 R Model 1966 Flintstone with END 711 engine, square fuel tanks, cast radiator, single

clutch, TRQ7220 5x4 gear box, heavy front axle, heavy tandem rear axle, steel bonnet -

500 pages.

$ 130.00

R MODEL 2055 1630 Parts Book 785 RST has ENDT 675 engine $ 100.00

MACK R WORKSHOP MANUAL 2056 1629 Workshop Manual - covers R-RD-U & DM models - 338 Pages. Chassis, cooling, front

axle, steering, springs, & suspension, wheels, brakes, electrical. Cabs. Came out with first

new Mack 1976.

$ 100.00

MACK R GENERAL MODELS 2057 1628 Workshop Manual - 937 Pages - Early - Covers Models B67-673-70. Includes Mack

C.M.B.F.R.U & Flintstone - For Engines END 465 - END 673 - ENDT 673 - ENDT673

& B - END 711 - END 864 - ENDT 864. Fuel pump, clutch, gear box, drive shaft, diffs,

came with our first new Mack in 1976.

$ 180.00

F MODEL 2070 Parts Book - suit F709 RT END 711 Engine - single clutch, TRQ 7220 gearbox 5x4, RHD

cross shaft steering, single rear axle, steel sleeper cabin 367 Pages $ 100.00

2071 1633 Parts book F785 RS first 8 pages, has damaged corners, 482 pages similar to book 1631

but has END T673 engine. $ 100.00

MACK L DRIVE HAND BOOK 2075 1644 L Model Glove Box drive hand book - Suit LJT & LJSW with Cummins Engine.

CUMMINS MAINTENANCE MANUAL 2085 1629 Cummins maintenance manual - suit NHH, Super 250, V555, VT903, NTC335 - 88 pages

CUMMINS SHOP MANUAL 2086 Cummins Shop Manual - Printed 8/73. 855 & 927 Series which include, NH230, NHD

230, NHF240, NHC 250, NHC250D, NHH250, NHF265, Power Torque 270, NTC 290,

NTF 295, NTC 335, NHHTC 335, NTC 350, NTF 365, NTA 370, NTA 400, NTA 420,

NHCT- CT, NHCT 270, NHTF 295, NT 3980 & 927 Series, Super 250 & Super 250/270.

$ 100.00

PARTS BOOKS

31 May 2020


RUBBER PARTS ALL PRICES ARE SUBJECT TO GST ADHESIVE - NO SLIP ADHESIVE. 2101 2749 Black high grip non slip adhesive backed rubber. 150 wide - sold

per metre. $ 9.00

BATTERY BOX LATCH 2102 3301 Short bonnet latch. Also suit battery box and some bonnets. PER

EACH. Length centre of mounting pin to latch connecting point 4

3/4-inch x 125mm.

$ 30.00

MACK SUPPLY LATCH 2103 3072 Battery Box Rubber Latch. Mack Supply $ 38.00

BAILEY CHANNEL (GLASS RUN CHANNEL) IS DESIGNED TO PREVENT NOISE, PROVIDE

SMOOTH MOVEMENT AND WEATHER PROOF SEAL FOR SLIDING GLASS

B DOOR BAILEY FLEXIBLE CHANNEL 2110 2501 Bailey channel flexible, stainless steel bead, rubber covered, pile

& felt lining suit Mack, Ford 52-56, Chrysler 55-56, Studebaker

53-62, Willys 50-55. SOLD PER METRE, EX USA, 15 mm wide,

15mm high & with Bead.

$ 80.00

DOOR RIGID VENT WINDOW PILLAR ONLY 2111 2510 Bailey channel rigid, pillar channel, stainless steel bead, pile

lining, 12mm wide 13mm high & with bead. Suit Mack B&R.

PRICE PER METRE.

$ 70.00

BAILEY CHANNEL - SUIT R & F MODEL MACK 2114 3549 Channel Bailey R&F. 2 per door. Price Per Each. Supplied with 5

clips. 1100mm per length.

Note: For quarter vent flexible, 1810 is OK but rigid looks better.

Supply 510mm of 2510 rigid with S/S bead.

$ 70.00

R & F VENT WINDOW CHANNEL 2116 Channel Bailey fits vent window channel. SEE OPTION ABOVE $ 33.00

BONNET (HOOD) CORNER RUBBERS 2120 Bonnet (Hood) universal corner rubber - slip on with brass rivet -

35mmx30mm. Price per each. $ 15.00

2121 Bonnet (Hood) universal angle corner rubbers - slip on - 35mm x

35mmx43mm. Price per each. $ 15.00

2122 Bonnet (Hood) universal square corner rubbers - slip on - 45mm x

45mm. Sold per pair. $ 30.00

2123 2614 Bonnet (Hood) universal angle corner rubbers - 60mm x

60mm.Sold per pair. $ 40.00

2124 Bonnet (Hood) universal corner rubbers - slip on -

80mmx55mmx55mm. Sold per each. $ 10.00

RUBBER PARTS

31 May 2020


RUBBER PARTS ALL PRICES ARE SUBJECT TO GST INTERNATIONAL 2125 2615 Bonnet (Hood) corner rubbers suit International R190-200 etc. Set

of 2 with rivets. 75mmx47mm $ 90.00

KW 2126 2618 Bonnet (Hood) corner rubbers - suit KW slotted pad type -

50mmx50mmx50mm.Sold per each. $ 15.00

INTERNATIONAL 2127 2703 International truck bonnet to mudguard bumpers and corners. Suit

US built International L, R, S 50-56. 10 bumpers & 2 corners.

PER SET.

$ 75.00

BONNET (HOOD) WOVEN LACING SMALL 2134 2690 Woven type hood lacing - 18x5mm (3/4 x 3/16) - sold per metre $ 20.00

MEDIUM 2135 2691 Woven type hood lacing - 25x5mm ( 1x3/16) sold per metre. Also

used on Ford Trucks H to C $ 25.00

2136 2692 Woven type hood lacing - 30x8mm ( 1 1/4 x 3/8). Sold per

foot. B Model rear cab end 2x1070mm per side. Supply 2692.

B Model steel front 2x600. B B 61 type. Supply 2691

B Model Alloy front 2x700. B 615 type

B Model - See Part no 1455 18 rear & 10

front. Set of 28 per truck for T Clips for back

and front.

$80.00 per

metre

BONNET INTERNATIONAL LACING 2140 2696 Rubber type lacing - suit International KB1 to KB12 Model etc.

25x5mm. Sold per metre. Ex USA $ 23.00

BONNET INTERNATIONAL SEAL 2141 2706 International hood to cowl seal. 9/16 x 3/8 high. Sold Per Metre. $ 19.00

BONNET LATCH RUBBER 2143 3302 Long bonnet latch. Suit Superliner 2 and others. Length centre of

mounting pin to latch connecting point - 7-inch x 180mm overall

length 330mm x 13 inch.

$ 89.00

SOCKET CLIP FOR 2143 2149 Clip for long rubber bonnet latch. Part No 2143. As fitted to

Superliner and Valveliner. PRICE PER EACH. $ 38.50

SOCKET CLIP FOR 2146 2150 Clip for short bonnet catch. Suit catch 2102 and 2103 $ 12.00

LOWER BONNET MOUNT KIT 2151 3260 Lower mounting kit for 3301 Bolt not included. $ 11.00

RUBBER PARTS

31 May 2020


RUBBER PARTS ALL PRICES ARE SUBJECT TO GST BUMP STOPS 2159 Flat head bump stops 55mm wide & 40mm high. 3/8 UNF 15mm

long bolt suit many models. $ 35.00

2160 Flat top spring bump stops - 58mmhigh 55mm wide. 3/8 UNF

15mm long bolt suit many other models. Suit B Mack light &

heavy front axle also R Mack. Sold per each.

$ 40.00

B MODLE REMOVABLE MUDGUARD PANEL 2163 Flat top B model removable fender - 22mm wide top x 10mm deep.

Sold per each. 10 Per B Model truck. $ 7.00

SUIT GLOVE BOX, FUEL CAP ETC. 2164 2812 Universal Dome head bump stop. Size Head wide 8mm x 3mm

high. Sold per each. $ 3.00

2165 2813 Universal Dome head bump stop - size head wide 9mm x 7mm

high. Sold per each. $ 3.00

B MACK GLOVE BOX 2166 Flat head top (glove box, fuel cap etc). 1/2 round 5/16 high, suit

1/4-inch hole. 4 Per Truck. Sold Per Each. Also, GM car door &

quarter glass bumper.

$ 3.00

BUMP STOPS - GENERAL 2167 2814 Flat head bump stop - 16mm high x 15mm wide with 8.32 thread.

Also some Fords. $ 3.00

2169 2815 Flat head top bump stop. 14mm high x 19mm wide. Also, some

Chevys. $ 3.00

2170 Flat head top bump stop - 12mm high x 22mm wide. $ 4.00

2173 Flat head top bump stops - 19mm high x 22mm wide. $ 4.00

R MODEL BONNET LATCH ( fits B) 2174 2846 Hood latch rubber cushion bump stop with steel backing 18mmw

12mm high. PER EACH. $ 25.00

ADJUSTING BONNET TYPE BUMP STOP 2179 2818 Flat head top bonnet (hood) adjusting bolt with bumper, Chrysler

to

1960's upwards & other models where adjustment of height is

required 31mm wide 13mm deep 30mm long bolt. 3/16 UNC.

$ 8.00

RUBBER PARTS

31 May 2020


RUBBER PARTS ALL PRICES ARE SUBJECT TO GST FLAT HEAD RUBBER SPRING BUMP STOPS. SUIT

MACK B & R & OTHERS

2180 2847 Hood latch replacement cushion rubber - NEW. Not as thick as

2174. SOLD PER EACH $ 7.00

R BONNET & SLEEPER MOUNTING RUBBERS 2183 Bonnet pivot mounting insulators. Supplied with 2 large lower & 2

small upper. Note: this part fits some R, V/Liner, S/Liner & early

Titans and rear cab and sleeper box mounts as well. Size 65x30

with 52x13 top. PRICE PER EACH.

FMT 4900 12-20 5/19 FMT 4900 12-20 5/19

$ 30.00

2184 Lower bonnet mount size 52mmx13. PRICE PER EACH. $ 10.00

BUMP STOPS CAB MARKER LIGHT PADS 2190 2667 Cab marker light moulded pad. Sold per set 5. Suit curved early

type Mack B and other early trucks. $ 140.00

RADIATOR & CABIN MOUNTING INSULATOR

CUP TYPE

2193 154 Mack B model special cup type cab mounting insulators, 2 large &

2 small required. They are 70mm diam & 30 high with 5/8 hole.

They require an 8-inch bolt at rear.

$75.00

Set as photo

B MODEL ROUND 2194 193 Rear cab mounting long bolts 8" x 5/8 with washer & nyloc nuts. 2

required per each $ 10.00

R CABIN INSULATOR 2197 3434 Cab front insulator R cabin. Also, R fuel tanks per each. 3 3/4 in

long overall x 2 5/8 diam x 1 1/2 hole are split for fitting. See

fuel tanks for option 2336.

$ 28.00

CENTRE BEARING & SHOCKER RUBBER 2204 2674 Centre bearing rubber, also fit some shockers. 25mm hole, 50mm

big end, 40mm small end & 28mm deep $ 10.00

B & R CLUTCH PEDAL RUBBER 2205 2482 Clutch rubber suit B & R Mack. Fits over steel plate 95mm long

and 50mm wide. Can be used on many other model brake pedals. $ 20.00

SHUTTER CONTROL PISTON REPLACEMENT 2207 Radiator control piston replacement seal 1 3/4 suit part 274 - new $ 9.10

DOOR SEAL - B MACK 2210 D shape car, truck, door soft hollow weather strip adhesive

backing. 14mm wide x 13mm high. Sold in 4 metre lengths for

one door. Sold per Each.

$ 60.00

Per door

OPTIONAL DOOR SEAL - R MODEL 2211 2559 D Shape car truck door soft hollow weather strip with R Mack

adhesive backing. 19mm wide 15mm high. 4.5m required for R

Model. SOLD PER DOOR

$ 65.00

Per door

RUBBER PARTS

31 May 2020


RUBBER PARTS ALL PRICES ARE SUBJECT TO GST DOOR SEAL - INTERNATIONAL & DIAMOND T 2215 2697 International lower door seal KB & L, R, S. US models. Lower

door seal 1940-56. Inter & Diamond T 30mm long 15mm wide T

pop. Sold Per Metre.

$ 12.00

2218 2698 International door seal front of cabin. US models single rear

window. 50-56. 14mm x 6mm Sold per Metre. $ 12.00

INTERNATIONAL TRUCK DOOR SEAL GUARD 2221 2699 Quarter round sponge square back type - 12x12., Sold per Metre. $ 12.00

2224 2700 Sponge extrusion - 12x12. Sold per Metre $ 12.00

INTERNATIONAL MUDGUARD SEAL DOOR & PANEL EDGE GUARD 2228 2544 5/16 DOOR EDGE GUARD BLACK. Made from strong nylon

type material. Sold per Metre. $ 6.00

UNIVERSAL DOOR SEAL 2230 2564 Universal door seal. Soft seal fits most cars. 13mm wide x19 mm

high. Sold per metre $ 6.00

BELT STRIP DOOR SQUEEGEE - UNIVERSAL 2234 2512 Half Bailey channel, rigid weather strip, stainless steel, rubber

covered, pile lining, 8mm thick 15mm high. Sold per Metre. Ex

USA

$ 21.00

UNIVERSAL DOOR GLASS SQUEEGEE SET 2235 2513 Set of 4 squeegee door glass guides for glass to glide on.

Universal set suit lots of makes and models. 420mm long 12mm

deep 6mm thick

N/A

B & R & F DOOR GLASS SQUEEGEE INNER 2236 3550 Weather strip R & F model R H door glass squeegee guides. -

1 required per door L & R. Price Per Each. $50.00

Each

R & F DOOR GLASS SQUEEGEE OUTER OPTION 2238 3546 Weather strip R&F model door glass squeegee guides with rubber

wiper seal and door lip curved section to rear - RH (one per door).

PRICE PER EACH

$50.00

Each

2239 3547 Weather strip R&F model door glass squeegee guides with rubber

wiper seal and door lip curved section to rear - LH (one per door) -

PRICE PER EACH

$50.00

Each

DOOR BAILEY CHANNEL KITS DOOR KIT - B MODEL 2241 2511 B Model door glass rubber channel curved radius kit, includes

flexible lining bailey channel with stainless steel bead for curved

radius top of door. One rigid & one flexible for removable window

panel in door and 2 squeegee glass guides for glass to glide in. B

Model door kit - 5 pieces. PRICE PER DOOR.

$ 300.00

RUBBER PARTS

31 May 2020


RUBBER PARTS ALL PRICES ARE SUBJECT TO GST DOOR KIT - R MODEL 2242 3552 R Model door glass channel curved kit. Top of door and 2

channels for removable window panel and 2 squeegee glass

guides.

$ 230.00

DRAG LINK COVERS 2245 303 B Model Drag link leather grease covers with leather lace & brass

eyelets - new.

AOS-9946 94 6/49

$ 20.00

DRAG LINK COVER - ORIGINAL 2246 Drag link rubber moulder boot - original type rubber with brass

eyelets and strips. PRICE PER EACH $ 120.00

B EDGE TRIM DASH & GLOVE BOX SEAL 2249 2538 Edge trim round edge - glass size -4 mm wide 1 /8 x 6 mm x 1/4

deep. Dash panel rubber mounting edge seal (1500mm). Fits

over inner edge/lip to save paint. Photo shows end view. Supply

1.4m for B glove & dash board. SOLD PER METRE.

$ 12.00

2250 2541 Edge trim square edge - 7 mm 1/4 wide x 8 mm 5/16 deep. SOLD

PER METRE. $ 17.00

2251 2540 Edge trim round edge - 12mmx10mm (1/2x3/8) glass size 5mm.

SOLD PER METRE. $ 17.00

2255 2550 Edge trim - round edge - 12 deep x 10 x 4mm glass size 3/16,

height 7/16. SOLD PER METRE. $ 48.00

ENGINE MOUNTING INSULATORS

2260 Mack B rear engine and gear box mounting rubber. Set includes 4

upper & 4 lower. They are 70mm diam & 30mm high with 5/8

hole. Sold per set of 4 (8 pieces). Photos shows both sides.

$300.00

(4 Sets of

2 Parts)

HOSES AIR INTAKE FITTINGS 2268 Air hose hump connector, straight, suit 5-inch tube. Suit

Superliner. $ 30.00

2269 2742 Air Hose hump straight suit 6-inch tube $ 45.00 2270 2740 Air elbow 38deg. Suit 5-inch tube POA

2271 2743 Air elbow 90 deg suit 6-inch tube. Suit Superliner $ 84.00

2272 2741 Air elbow 90 deg. Suit 5-inch tube $ 45.00

2273 2744 Air elbow 90 deg suit 6-inch tube. $ 55.00

FOR AIR BRAKE HOSE (SEE BRAKE PARTS)

RUBBER PARTS

31 May 2020


RUBBER PARTS ALL PRICES ARE SUBJECT TO GST HOSE SILICONE COOLANT BLUE 2277 2720 Silicon Hose - 1 inch (25mm). SOLD PER 100mm. 272 $ 12.00

2278 2721 Silicon Hose 1 1/2 inch (38.1mm) sold per 100mm $ 15.00 2280 2722 Silicon Hose - 2 inch (50.8mm) Sold per 100mm $ 16.00 2281 2723 Silicon Hose 2 1/2 inch (63.5mm) Sold per 100mm. $ 18.00 2282 2724 Silicon Hose - 3 inch (76.2mm) Sold per 100mm $ 24.00

2283 2725 Silicon Hose - 4 inch (101.6mm) Sold per 100mm $ 30.00 2284 2726 Silicon Hose - 5 inch (128mm) Sold per 100mm $ 39.00 2285 2727 Silicone hose 6 inches (2.250mm) S o l d per 100mm. $ 45.00 SILICONE COOLANT HOSE -BLACK (OLD TIME) 2289 2730 Silicone hose 2 1/4 inch (57 ID). SOLD PER 100mm $ 16.00

2290 2731 Silicone hose - 3 inch (76mm). SOLD PER 100mm $ 18.00 2291 2732 Silicone hose - 4 inch (1.2mm). SOLD PER 100mm. $ 25.00 SILICONE COOLANT FITTINGS 2295 2711 Short elbow 2 1/8 (56mm) ID

B MODEL FLOOR MATS -MOULDED MACK 2301 2761 B61 type ribbed moulded front floor mat with Mack logo and

heavy backing. Weight 5 Kg. $ 600.00

B REAR FLOOR MAT 2302 2762 B61 type ribbed moulded floor mat with heavy backing (goes

under seat). Weight 4 Kg. $ 480.00

B MODEL FIREWALL INSULATION

2303 B Model Firewall insulation under dash down to floor mat, cover

with heavy insulation on the back for noise & heat-original type

RH drive model with clutch pocket- new

$ 355.00

R FRONT FLOOR MAT

2305 3391 R Model front floor mat - moulded rubber ribbed with Mack logo

& wear section on LH side. $ 350.00

R MODEL REAR FLOOR MAT 2306 3392 R Model rear floor under seat mat - moulded ribbed r u b b e r

FMT 5733 166 7/19 ROC177 $ 230.00

R MODEL MAT UNDER DASH 2307 3394 Firewall insulation, fits under dash insulation for noise and heat.

Also available in carpet finish. $ 350.00

MAKE YOUR OWN FLOOR OR TRAY MATS 2313 2640 Roll of big rib rubber sheeting 2m wide - make your own floor or

ute tray mat - SOLD PER METRE. $ 160.00

LOOSE FLOOR MATS 2316 2771 Loose floor mats with Mack logo L&R. Weight 2.5Kg. SOLD PER

PAIR $ 165.00

RUBBER PARTS

31 May 2020


RUBBER PARTS ALL PRICES ARE SUBJECT TO GST TANK STRAPPING SQUARE EDGE 2320 2825 Fuel/ air etc tank strapping - square edge - 32mm ID, Sold

per metre $ 13.00

SAMPLE

PHOTO

2321 2826 Fuel tank strapping - square edge - 38mm ID Sold per metre $ 14.00 2322 2528 Fuel tank strapping - square edge - 50mm ID. Sold Per Metre. $ 14.00

2323 2527 Fuel tank strapping - square edge - 80mm ID 31/4 mm. Sold Per

Metre. $ 16.00

FUEL TANK STRAP ROLL OVER TYPE 2325 Rubber fuel tank strap 401D - Sold per metre. Allow 1 metre per

band for B & R Model air cleaner $ 14.00

2326 3085 Rubber Fuel Tank Strap 50mm ID - 2 inch. Comes in bag of 12ft.

(3650mm). See low shelf below for stock $87.00

For 12ft

FUEL TANK STRAP ROLL OVER 2328 Rubber fuel tank strap 65mm 2 1/2 rollover tank strip $ 14.00

R FUEL TANK FLAT STRAP- MACK SUPPLY 2329 3084 R Mack fuel tank flat strap. 2 1/8 wide, 1/8 thick, 15 Metre Roll.

(has no edge turn up) SOLD PER ROLL

12A x 126F

$ 140.00

TANK SUPPORT RUBBER 2336 3435 R fuel tanks support rubber. Price per each. 3 3/4 in long x 2 5/8

diam x 1 1/2 hole are split for fitting. $ 21.00

GASKET RUBBER RADIATOR 2342 2860 Rubber gasket suit top and bottom radiator tanks - B615 & 75 and

the like. 2mm thick 30mm wide. Sold per metre $ 25.00

GEAR SHIFT BOOT 2343 Gear shift boot - rubber 175mm long x 130mm wide x 100mm

high, 15mm gear lever hole but extra place for shifter wires or 2

speed wires

$ 95.00

BOOT TYPE INSULATORS GEAR SHIFT BOOT 2344 Gear Shift Boot rubber, 175mm long x 130mm wide, height and

hole as 2345 below. FMT 1506 30 7/19 $ 99.00

GEAR SHIFT& STEERING B O O T 2345 2869 Gear shift boot rubber - 180 long 100 wide 100 high.

Suit B & R Model and most other model cabins and controls. $ 91.00

TRIM BOOT MOUNTING RING 2346 2868 Stainless steel surround for gear shifter boot 2345 above. $ 25.00

RUBBER PARTS

31 May 2020


RUBBER PARTS ALL PRICES ARE SUBJECT TO GST GEAR SHIFT LEVER BOOT 2348 Rubber gear shift boot 240mm long 150mm wide 280mm high.

50mm hole on top.

FMT 15228 MY 51A

GEAR BOX LEVER DUST BOOT 2349 2872 Gear box dust seal. Suit 18mm gear lever shaft 60mm OD. Suit

most Models. $ 23.00

UNIVERSAL SHAFT BOOT 2351 2870 Steering shaft or gear shift boot rubber - suit some R Models -

222mm long 135mm wide 70 high. $ 99.00

BOOT TYPE INSULATORS PEDAL STEERING FLOOR BOOT 2352 2665 Mack early oval grommet, Suit 3-inch hole in mounting plate with

2 1/4 x 1 1/2-hole centre. $ 55.00

RADIATOR MOUNTING INSULATOR

2353 2738 Lower mounting 2-piece insulator V8. PRICE PER SET

(as photo) $ 38.00

2354 2737 Insulator Radiator stay side set of 4 cross tie mounting. Top 43mm,

bottom 30mm, height 30mm, Hole 12mm. Set of 4 $ 42.00

STEERING SHAFT BOOTS 2356 3097 Bearing seal 25mm shaft 65mm OD 25mm deep. $ 17.00

OPTIONAL DUST SHAFT SEAL 2357 3098 Slip Yoke dust seal. Suit 4 splines. 1 1/4 shaft. $ 28.00

BLINKER WIRING COVER BOOT 2359 773 Turn signal wiring cover boot kit fits over wiring under fenders

(mudguards) turn signal light (blinker above) - SOLD PER

EACH.

$ 25.00

DOOR GLASS SETTING CHANNEL & QUARTER

VENT GLAZING SEAL - HOLDS GLASS IN PLACE.

2362 2861 Quarter vent and door glass holding rubber. 400mm per B door,

700mm per B vent. Softens with kero to help fitting. When dried

makes strong bond to glass. Used with door glass channel lifter

and quarter vent glass in its frame and some windscreen and glass

frames. Sold per metre. 1 1/2 WIDE X 1/16 THICK. (1.5X87MM).

$2.18 per 200mm.

$10.00

Per Metre

RUBBER PARTS

31 May 2020


RUBBER PARTS ALL PRICES ARE SUBJECT TO GST CLOSED HOLE BLANKING GROMMET OPTIONS

2368 2669 9 Sizes - 6mm to 50mm Price Per Each $2.00

for 9 size

options

2370 2670 Blanking - 60mm $ 3.00

EXTERIOR SUNVISOR MOUNTING - RUBBER 2373 2644 Grommet type rubber insulator for sunvisor mounting. Per Each. $ 3.00

MUDGUARD SEAL - MACK B 2375 2565 Suit head light panel to radiator - B Mack, very flexible, 7mm

piping, 30mm flat section, suit many applications. Beaded vinyl

moulding seals headlight panel to radiator shell and to outer

mudguard. Note: Special rubber edge trim can also be used but

extra work normally takes 650 per section or 2600 per truck size

40mmx10mm. (note: 615 - 73 & 75 only need 1300) SOLD PER

METRE.

$ 30.00

T SECTION 2376 T Section joint rubber - 50mm x 10mm. SOLD PER METRE $ 20.00

ROUND OFFSET SECTION 2378 2552 Round offset edge seal - 25mm x 7mm. Diameter round section.

SOLD PER METRE. $ 20.00

ROUND CENTRE SECTION 2381 2553 Round centre 25mm flat with 9mm diameter round section. Sold

Per Metre $ 15.00

INTERNATIONAL MUDGUARD SEAL 2384 2701 International rear mudguard ribbed rubber welt 5/16 x 1 1/2 inch.

Sold per Metre. $ 14.00

HOLLOW PIPE SEAL 2386 Hollow pipe joining rubber - 35x11. SOLD PER METRE. $ 20.00

MUDGUARD (FENDER SEAL) MACK B 2388 2685 Mudguard to cab edge fender welt seal - 40Wx8Hx8W. 3 feet 2

inch per side. Sold per metre. Ex USA $ 18.00

RUBBER PARTS

31 May 2020


RUBBER PARTS ALL PRICES ARE SUBJECT TO GST MUD FLAPS - REAR 2391 3086 Mack mudflaps - white with facing dogs, as on Bicentennial Super

Liner. 600 w, x 400 drop. Australian made. 4kG PER EACH

...PRICE PER EACH

$50.00

Per Each

MUDFLAPS - SUIT UTILITY (PICK UP) 2394 1198 White heavy mudflap ute 280mm (8ins) wide c 280mm (11ins)

deep. Australian made. Sold per each $25.00

Per Each

CUSTOM MUD FLAPS 2404 Personal mud flaps to your requirements. 610 wide maximum,

length 760. Vehicle make and description optional. Price Per

Each

$ 130.00

FRONT MUDFLAP 2407 3340 Mudflap bonnet LH, R Model black. Not Valveliner. Supplied

with brass eyelets and moulded top mounting r e b a t e . PRICE

PER EACH

$ 96.00

2408 Mudflap bonnet RH, R Model black. Not Valveliner. Supplied

with brass eyelets and moulded top mounting r e b a t e . PRICE

PER EACH

$ 96.00

SLEEPER SEAL PINCH WELD 2409 2882 Pinch weld - suit sleeper & tool box doors. Clips on. 5mm thick

edge has 20mm x 15mm bubble seal. Ask us to post sample. $ 15.00

RUNNING BOARD RUBBER 2410 2641 Ribbed running board rubber strip 425mm wide. Sold per metre. $ 15.00

SLEEPER TO CAB SEAL 2420 Universal sleeper seal, an efficient seal designed to connect and

seal crawl space between the driving and sleeping cabins in trucks.

6 inches wide. Can close to 5 inches and open to 7 inches wide x

25 deep. Sold per metre. Weight 4 m = 1Kg.

$50,00

Per Metre

R MACK CRAWL THROUGH SLEEPER SEAL Crawl through opening supply. 3.1 metres including shipping

Australia wide. $ 140.00

R MACK V WALK THROUGH SLEEPER SEAL Walk through opening with V opening. Supply 4metres including

shipment Australia wide $ 200.00

FITTING SEAL

Sleeper mounting may be best to mount say 3 inches gap between cab & sleeper, depending on seal

mounting location. If cab is on air then sleeper gap would be better at larger gap. FITTING - start at

bottom centre and seal and clamp seal around opening back to lower centre. When happy with

connection, cut seal for pressure fit and seal with rubber glue, seal is Australian made.

RUBBER PARTS

31 May 2020


RUBBER PARTS ALL PRICES ARE SUBJECT TO GST SPRING RUBBERS FRONT SPRING INSULATOR 2441 Front spring insulator. Suit B61 and most other B models. Price

Per Each

EM44720 10QK 332A 45 6/19 22

$ 80.00

ELEPHANT FEET INSULATOR 2444 2758 Top insulator suit 34-38000 steel base, 6insx4 1/2 ins 1 3/4 dowel.

4 Required. Price Per Each $ 55.00

2445 2754 Top insulator - suit 44000. 4 Required. Price Per Each $ 65.00

2446 2760 Top insulator, suit early 44000 with smaller locating dowel. Note:

these are modified in our workshop to 33mm dowel, top plate 6 x 4

1/2 inch, 3-inch-deep & dowel. Cost to modify add $35. Price Per

Each.

$ 65.00

2447 Lower insulator. Suit 34-38 & 44000 rear end. Steel Base 6 1/8 x

6 1/8 1 3/4 dowel. 4 Required. Price Per Each $ 65.00

2448 2757 Side Spacer of lower insulator Neoprene. 8 Required. Price Per

Each. $ 25.00

ALSO SEE BUMP STOPS SPONGE EXTRUSION 2459 2755 Sponge - 8mmx10mm. Sold Per Metre. $ 10.00

2460 2565 Sponge extrusion 18x9mm. Sold Per Metre $ 8.00

2462 Sponge Extrusion 13 x 7mm. SOLD PER METRE $ 8.00

EDGE TOOL BOX STRIP 2473 2561 Sponge tool box flat strip, super fine with stick back - 18mmx

1.6mm Sold Per Metre $ 3.00

2477 2567 Universal rectangular stick back seal rubber. 3/8-inch-wide

3/16 high. (9mm x 5mm) Sold Per Metre. $ 8.00

2479 2569 Sponge seal square extrusion with sticky back - 20mmx12mm.

Sold per Metre $ 11.00

RUBBER PARTS

31 May 2020


RUBBER PARTS ALL PRICES ARE SUBJECT TO GST STICKY BACK WEATHER STRIP 2487 Tool Box Sticky Weather Strip. 18 x 1.6mm. Sold Per Metre $ 3.00

DOOR QUARTER VENT SEALING RUBBER - SUIT

B MODEL MACK - NEW

2501 2452 Quarter Vent window rubbers (pair) - fit to door to seal pivot glass

closing to frame - new. Sold as pair only. $ 240.00

DOOR QUARTER VENT SEALING RUBBER - SUIT

B MODEL MACK - USED

2502 2453 Quarter vent rubber complete and pliable - suit older restoration

job. - Used. L & R. Price Per Each. $ 50.00

B DOOR QUARTER VENT WINDOW POST SEAL 2504 2454 B model vent window post rubbers (seals glass vent to the rear

upright post when glass is closed straight). Sold per each - 2

required per truck.

$ 40.00

DIAMOND T NOTE: DIAMOND T CABINS WITH 2 BACK WINDOWS

SAY MODEL 323-420-520 etc USE A SHORTER DOOR

QUARTER VENT RUBBER.

2508 2469 Quarter vent rubber set, Diamond T type cabin with twin rear

window. $ 287.00

2509 2468 Quarter vent rubber set for Diamond T type cabin, with single back

window and press button door handles. Suit Models 522-531-630. $ 273.00

INTERNATIONAL 2511 2705 Quarter vent rubber set for USA type cabin. Late R190 & R200

with single back window and curved dash and press button door

handles.

$ 253.00

VENT TRIM - EDGE B & R MACK SIDE 2512 2621 Sponge extrusion - suit Mack. B & R Model side vent -

10mmx8mm, Sold per metre. - 700mm (27 1/2 inches) per vent. $ 12.00

ALSO SEE DOOR RUBBERS (UNDER DOOR SECTION)

B MODEL WINDSCREEN (WINDSHIELD) RUBBER 2515 2800 B Model Mack windshield rubber moulding supplied as one piece -

see part 2523 for lock strip - new. $ 490.00

REAR WINDOW RUBBER MOULDING - B & R

MODEL

B. MODEL REAR WINDOW 2519 2801 Rear cab (window) rubber moulding and lock strip to hold glass.

2.1m (7ft2inches). $ 60.00

R MODEL REAR WINDOW 2520 Rear cab window rubber moulding and lock strip to hold glass 3.1

metres $ 80.00

4774 R Mode Front Rubber $ 230.00

RUBBER PARTS

31 May 2020


RUBBER PARTS ALL PRICES ARE SUBJECT TO GST UNIVERSAL WINDOW GLASS MOULDING 2521 COST PER METRE FOR OTHER APPLICATIONS

25MM X 18MM

$ 25.00

LOCKING KEY 2523 2802 Mack lock strip key for windscreen (needs 4.1metres) and rear

window, front and back needs 6.3 metres. Also suit R & B model.

Sold per metre - new.

$ 5.00

MACK F MODEL WINDSCREEN RUBBER - F 2525 2804 Windscreen rubber F Model Mack $ 180.00

Lock Strap for above DIAMOND T REAR WINDOW RUBBER - DIAMOND T 2528 2470 Rear window rubber single glass. Suit 522 - 531 - 630. And other

Diamond T models up to 1959. Then Diamond T had White built

cabins.

$ 170.00

2529 2471 Rear window double glass - suit 323 - 420 - 520 $ 220.00

WINDSCREEN RUBBER 2531 2472 Front windscreen rubber. Suit 1950 to 1959 Diamond T. 323 -

420 - 520 - 522 - 531 - 630 and other Diamond T models up to

1959, after that Diamond T had White built cabins.

$ 310.00

COWL VENT RUBBER 2532 2473 Cowl vent gasket - suit 1951 - 59 Diamond T. $ 45.00

DIAMOND T CAB RUBBER KITS 2534 2467 Complete rubber cabin kit for Diamond T type cabin - R190

& R200 with single rear window and press button door

handles. Limited Stock.

$ 1,100.00

RUBBER PARTS

31 May 2020


STEEL INFORMATION PLATES

ALL PRICING SUBJECT TO GST STEEL NAME PLATES - MACK SELECTION AIR TANKS 2601 1230 MACK - AIR TANK Specification plate - 152mmX76mm. $

45.00

2602 1229 MACK - DRAIN AIR TANKS DAILY - 70mmX40mm. $

42.00

2603 1227 MACK - DRAIN AIR TANKS DAILY - 125mmX66mm. $

45.00

CHASSIS 2606 1224 MACK - DO NOT WELD CHASSIS OR DRILL FLANGE -

70mmX50mm. $

42.00

2607 1225 MACK - DO NOT WELD CHASSIS OR DRILL FLANGE -

125mmX66mm. $

45.00

DASH PLATES 2610 DASH PLATE - CAUTION ENGINE OPERATING RANGE

95x40mm. $

35.00

DOOR VIN CHASSIS NUMBER BLANK PLATES

DIAMOND T

2613 Diamond T standard door chassis ID plate - 95x85mm $

55.00

MACK DOOR PLATES 2615 1242 MACK TRUCKS INC - PLAINFIELD N.J. U.S.A. -

152mmX76mm. $

60.00

2616 1243 MACK TRUCKS Inc - NEW YORK - 152x76mm. $

60.00

ID PLATE - INTERNATIONAL 2619 1318 Cab ID & Specification plate - suit most models built in Australia

including R190, R200. $

60.00

ID PLATE - WHITE TRUCK 2622 Cab ID & specification plate. Note: top not cut out. 130 high x 110

wide. $

60.00

DIFF SHIFT PLATES 2624 1287 Original 2 speed Electric Shift Plate - generally fitted behind

sunvisor - 250x66mm $

60.00


31 May 2020


STEEL INFORMATION PLATES ALL PRICING SUBJECT TO GST ENGINE PLATES CUMMINS ENGINE ID STEEL PLATE 2626 Cummins original early type engine ID plates - 220mm (81/4 ins)

length x 38mm (1 1/2 ins) width. Steel fits on timing gear cover. $ 60.00

R MODEL ENGINE PLATES 2629 1232 Mack engine exhaust emission control information rocker cover

plate. 200mm long x 70mm high. $ 80.00

FIREWALL - DIAMOND T 2631 1762 Diamond T General Information under dash P lat e - 162x90mm. $ 60.00

R MODEL FIREWALL PLATE 2632 1235 R Model firewall ID plate 90x90. Bin 1234 $ 60.00

R MODEL FIREWALL VENT MSR RATING 2634 1233 R Model Firewall ID plate 90x90 with MSR rating. $ 60.00

FUEL TANK 2637 1763 Brisken Original Greg Style Fuel Tank ID Plate - suit Diamond T

630. $ 60.00

FUEL TANK 2639 Mack fuel tank ID information plate. B & early R. $ 60.00

MACK AUXILIARY TRANSMISSION 2641 3 SPEED auxiliary transmission gear plate

STEEL NAME PLATES - MACK GEAR SELECTION

2642 1207 MACK STEEL PRINTED GEAR SHIFT PATTERN PLATES

AUXILIARY TRANSMISSION 152mmX65mm. $ 60.00

2643 1209 MACK TRANSMISSION 5 SPEED DIRECT - 95mmX65mm. $ 60.00

2644 1210 MACK UNISHIFT - DO NOT USE 5 IN LOW - 152mmX65mm $ 60.00


31 May 2020


STEEL INFORMATION PLATES ALL PRICING SUBJECT TO GST STEEL NAME PLATES - MACK GEAR SELECTION

(CONT)

2646 1211 MACK - 9 SPEED OVERGEAR TRANSMISSION -

150mmX65mm $ 60.00

2647 MACK - 10 SPEED DIRECT TRANSMISSION - 150mmX70mm $ 60.00

2648 1213 MACK - 10 SPEED OVERGEAR TRANSMISSION -

150mmX70mm. $ 60.00

2649 1214 MACK - TRT - 72 TRIPLEX 15 SPEED - 152mmX65mm $ 60.00

2657 1215 MACK - TRO - 72Q - QUADRUPLEX (20 SPEED

OVERGEARED) 152mmX65mm. $ 60.00

2658 1216 MACK - 18 SPEED QUADRUPLEX (20 SPEED

OVERGEARED) 152mmX65mm $ 60.00

2661 1956 MACK - LTL GEAR SHIFT PATTERN 5 X 4 - 130mmX80mm. $ 60.00

STEEL ROUND & OVAL SMALL MACK SCRIPT

PLATES

2664 1245 MACK - small round steel printed script - fits 44000 axle cap &

can be used in steering wheel centre - 60mm diam. $ 15.00

2667 1253 MACK - OVAL SCRIPT - 60X37. Note: oval section not cut out

or drilled. $ 15.00

CUSTOM ENGINE PLATES - MADE TO ORDER TURNTABLE 2669 1239 TURNTABLE PLATE BLANK - MACK TRUCKS Inc.

PLAINFIELD N, J. U.S.A. - Type/Year. 130x40mm. $ 35.00


31 May 2020


INFORMATION LABELS ALL PRICING SUBJECT TO GST AIR CLEANER SERVICE INSTRUCTIONS - R

MODEL

2701 1276 AIR CLEANER SERVICE INSTRUCTIONS for EBA15 as

fitted to Superliner and other models. 180mmx145 $ 20.00

AIR CLEANER ELEMENT - R MODEL 2702 1278 AIR CLEANER ELEMENT INFORMATION sticker. Length

120mmx70mm $ 20.00

AIR CLEANER - B MODEL 2704 1266 Donaldson air cleaner - black striker with white writing. Mack

logo with B model ID - 134x49mm $ 20.00

AIR CLEANER B MODEL OIL INSTRUCTIONS

2705 1231 Oil Level Instruction Sticker. For oil bath air cleaner. $ 20.00

AIR CONDITIONING 2709 1281 CASTROL COOLANT - ADD ONLY PREMIUM 50.

CHANGE EVERY 4 YEARS. DO NOT MIX - with Mack

logo

$ 10.00

2710 1267 IMPORTANT - RE SERVICE

AIR HORN 2713 1280 HORN COVER LOGO. Rectangular horn cover mirror

background 110mm long 55mm high. Wording is 107mm long $ 20.00

BATTERY 2717 1300 Battery Service Warning. Negative Ground System. 100mm x

65mm. $ 20.00

BRAKE ID CONTROL PLATES TO SUIT SIDE TO SIDE VALVE 583. SEE BRAKE

SECTION FOR MORE DETAIL - ALL MOUNTED- O N

PLATE

2720 1247 Truck Tractor Brake control lever plate with Mack logo normal

emergency - cut out and made lever slot. $ 50.00

2721 1249 Power divider Dry or Slippery Road ID control plate with steel

backing and logo. $ 50.00

2722 1252 Power divider IN/OUT ID plate with steel backing and logo -

option $ 50.00

2723 1217 Air suspension normal or deflate ID plate with backing and

logo $ 50.00

INFORMATION LABELS

31 May 2020


INFORMATION LABELS ALL PRICING SUBJECT TO GST BRAKE ID CONTROL PLATES (CONT) 2724 1218 Trailer Air Supply ON/OFF. ID plate with backing and logo. $ 50.00

2725 1219 PTO In/Out Sticker $ 50.00

OPTIONS WE CAN ALSO OFFER VALUE DESCRIPTION

PLATES FOR YOUR CUSTOM TRUCK WITH A

MAKER OF YOUR CHOICE.

BRAKE PIPING SCHEMATIC STICKER 2730 1186 Dual Circuit Air Brake System Color Coded Master. Size

300x200mm. Sticky Back. $ 55.00

BRAKE PIPING SCHEMATIC HARDBACK 2731 1187 Dual Circuit air brake system Color Coded Master on steel

backing for door mounting. See small store. $ 65.00

BRAKE WARNING 2734 1183 Auxiliary Brake Warning. 40x40 $ 20.00

SPRING BRAKE ID PLATE 2735 1251 Spring brake ID plate. Up Down Lever. Type with lock. $ 39.00

DOOR ENTRY WARNING 2738 DOOR ENTRY WARNING sticker. 100x60mm $ 20.00

ENGINE AIR CHANGE CLAMPS 2741 1268 MAINTAIN CHANGE AIR CLAMPS AT 7.3Nm (65lbs) -

with Mack logo 66x48mm $ 10.00

ENGINE BRAKE MAXIDYNE 2745 1241 MAXIDYNE OPERATING INSTRUCTIONS 110x53 $ 20.00

STARTER 2749 1170 PRESS TO START $ 10.00

JACOBS 2754 1178 Jacobs Engine Brake $ 10.00

INFORMATION LABELS

31 May 2020


INFORMATION LABELS ALL PRICING SUBJECT TO GST ENGINE (CONT) ENGINE JACOBS B R A K E PLATE 2755 1250 Engine Brake ID Plate with backing. $ 30.00

JAKES BRAKE OPERATING INSTRUCTIONS 2756 1172 Jakes brake operating and driving tips $ 20.00

ENGINE OPERATING INSTRUCTIONS 2759 1179 START AND SHUT DOWN INSTRUCTIONS 200mm

LONG 111 HIGH $ 20.00

DYNATARD INSTRUCTIONS 2761 1182 Correct Dynatard Operation Instructions. 75x60 $ 20.00

DIFF 2 SPEED SHIFT PLATE 2763 1287 Original 2 speed Electric Shift Plate - generally fitted behind

sunvisor - 250x66mm. Suits trucks with Eaton 2 speed electric

shift.

$ 20.00

GENERAL CUMMINS 2765 1272 Cummins Cross Sticker - 175mm long x 100mm high $ 20.00

ENGINE OIL 2768 1261 USE ONLY MACK APPROVED ENGINE OIL - with Mack

logo - 66x48mm $10.00

ENGINE FAN 2770 1269 ATTENTION: MAINTAIN EQUAL CLEARANCE AROUND FAN

AFTER ADJUSTING BELTS. THE BELT SURROUND MAY

REQUIRE ADJUSTMENT. With Mack logo -

66x48mm

$10.00

2772 1270 AUTOMATIC FAN - KEEP HAND FREE w i t h Mack logo -

66x48mm $10.00

COOLING SYSTEM 2773 1263 CAUTION: COOLING SYSTEM FITTED WITH

FLEETGUARD PG PLUS - with Mack logo - 66x48 $ 10.00

CHASSIS FRAME 2775 1264 HEAT TREATED FRAME - DO NOT WELD OR DRILL

HOLES IN UPPER OR LOWER FLANGES with Mack logo.

66x43mm

$ 10.00

2778 1283 USE ONLY CUMMINS APPROVED ENGINE OIL -

66X48mm $ 10.00

INFORMATION LABELS

31 May 2020


INFORMATION LABELS ALL PRICING SUBJECT TO GST ENGINE WARNING 2779 1184 Low Water, Oil Pressure, High Water Temperature. 40x40 $ 20.00

ENGINE STARTING INSTRUCTIONS 2780 1185 Starting Cold Engine. 150x100. $ 20.00

ENGINE OPERATING INSTRUCTIONS 2781 1179 START AND SHUT DOWN INSTRUCTIONS 200mm

LONG 111 HIGH $ 20.00

2785 GM - Jimmy Diesel. Black, red & white early man with pen

and paper cutting operating costs. 120x100mm $ 20.00

GM DETROIT 2786 1305 Detroit Diesel red, yellow & black - 80mm square $ 20.00

2787 1306 Detroit Diesel Power, red, yellow & black. - 80mm square $ 20.00

2788 1316 GM side bonnet (hood) plate 200mm long mounted on

aluminium backing for mounting. Price per each. $ 30.00

GAUGE INDENTIFICATION STICKER CARRIER (DIFF) 2793 1174 Gauge face sticker for diff 1 or 2. Suit 1 3/4 diam Face $ 15.00

ENGINE TEMPERATURE 2794 1175 Gauge face sticker for engine temperature Suit 1 3/4 diam face. $ 15.00

TRANSMISSION TEMPERATURE 2795 1176 Gauge face sticker of Transmission - suit 1 3/4 diam face. $ 15.00

SET OF 4 TEMPERATURE GAUGE ID LABELS 2796 1177

Set of 4 as above gauge stickers.

$45 or

$15 each

DASH R SWITCH LABELS 2801 1173 Replacement switch labels to stick onto existing backing. HTD

mirrors, driving lights, clips, panel LPS, off AM, roof warning.

27mm long x 10mm high. Others available on request. Price

Per Set of 9 - $60 or $10 each

$60.00

INFORMATION LABELS

31 May 2020


INFORMATION LABELS ALL PRICING SUBJECT TO GST GEAR SHIFTING GEAR TRANSFER CASE 2803 1237 COMPOUND TRANSFER CASE - 120x60 $ 20.00

`

GEAR SPLITTER SHIFTING INSTRUCTIONS 2804 1180 Shifting Instructions TRDL 1070/TRTxL 1070. 140x120 $ 20.00

GEAR TRANSMISSION T2090 2806 1244 CAUTION T2090 TRANSMISSION $ 20.00

GEAR MAXITORQUE SPLITTER

TRANSMISSION

2807 1181 Shift Sequence 150x110 Maxitorque extended range overdrive

splitter transmission. $ 20.00

MAXITORQUE NINE SPEED 2809 1188 Maxitorque T2090 Nin Speed. 125mmx65mm $ 20.00

GENERAL MAXITORQUE T2180 EIGHTEEN SPEED 2811 1189 Maxitorque 18 speed extended range splitter transmission $ 20.00

GEAR SHIFT 2812 1200 TRXK 1071 $ 20.00

2813 1201 TRXL 107 $ 20.00

GEAR SHIFT 5 SPEED WITH LOW & DRIVE AIR

SHIFT

2814 1205 194 523 $ 20.00

GEAR SHIFT 5 SPEED AIR SHIFT 2816 1206 194 - 514 $ 20.00

INFORMATION LABELS

31 May 2020


INFORMATION LABELS ALL PRICING SUBJECT TO GST GENERAL NOTE: WE CAN MAKE WITH OTHER LOGO ON

REQUEST.

PETROL & OIL STICKERS 2834 1259 Kangaroo - small - 200 wide x 160 high $ 30.00

2835 1260 Kangaroo - large 440 wide x 350 high $ 40.00

SAFETY 2839 1284 BE CAREFUL - 40long x 120 high $ 20.00

TRAVEL 2841 1303 GONE NORTH A'DROVING - 260 long x 190 high $ 20.00

WATER 2843 1304 DRINKING WATER STICKER - 125 LONG X 40 HIGH $ 10.00

HISTORY 2845 1296 PRESERVE OUR HISTORY 30 high x 300 wide $ 22.00

INTERNATIONAL 2854 5053 International logo 80mm high $ 20.00

2855 5054 International logo - 500 mm high $ 20.00

2856 5055 "IF IT'S NOT RED LEAVE IT IN THE SHED" - 380 long $ 20.00

BIG MACK OUTDOOR SIGNS 2860 1221 Mack Service outdoor/indoor. 1.2 metres wide x 1.1 high $ 210.00

2861 1220 Big Mack sign - Outdoor or Indoor with own company or

collection. Size 1220x490mm $ 220.00

INFORMATION LABELS

31 May 2020


INFORMATION LABELS ALL PRICING SUBJECT TO GST GENERAL REAR WINDOW SHADOW DOG LOGO 2864 1254 Right Hand Shadow Dog Logo. 200mm long. Has sticky on

rear. $ 30.00

2865 1254 Left hand Shadow dog - 200m long, Has sticky on rear. $ 30.00

MACK BIG SCRIPT VINYL LETTERING 2868 1257 MACK - " I WISH I WAS A MACK TRUCK" $ 20.00

MACK LOGO 2869 1281 Mack logo 110mm long x 55mm high $ 20.00

MACK DOG LOGO 2870 1223 Dog Standing on MACK Truck $ 20.00

2871 1222 Mack Dog Logo $ 20.00

R MACK STEERING WHEEL CUSTOM CUSTOMER

LOGO

2874 1258 Horn button custom built logo. Supplied with your details on

stainless steel mounting plate to stick into own existing horn

button.

$ 50.00

MACK WEE PEDAL CAR LOGO (Note size) 2876 1297 Steel craft pedal car gauges- small 40x25mm. Large -

50x30mm $ 10.00

2877 1289 Mack scroll logo for pedal car. 200x65mm $ 10.00

2878 1298 AC Mack pedal car hood logo. 100mm diam $ 10.00

2879 1299 AC Mack pedal car side logo. 80mm wide x 65mm high $ 10.00

INFORMATION LABELS

31 May 2020


INFORMATION LABELS ALL PRICING SUBJECT TO GST GENERAL CRUSH ZONE 2882 1290 WARNING - HOT AND HAZARDOUS EXHAUST -

80mmx60mm. $ 10.00

2883 1291 WARNING CRUSH ZONE - KEEP CLEAR $ 10.00

WEE MACK STEERING LOCK ADJUST

STICKER - 60x30mm

2886 1246 STEERING LOCK ADJUST STICKER - 60x30mm $ 10.00

POWER STEERING 2887 1262 POWER STEERING FITTED WITH DEXRON OIL ONLY-

with Mack logo - 66x48mm $ 10.00

TOWING 2891 1236 WARNING TOWING $ 20.00

WARNING - SAFETY 2893 DO NOT SCREW WITH MY MACK $ 20.00

CATERPILLAR 2895 1308 Caterpillar - 300mm long $ 20.00

2896 1309 Caterpillar - 300mm long $ 20.00

2897 1310 Caterpillar 380 long $ 20.00

EUCLID 2900 1286 Round 200mm diam original sticker with pioneer man pointing to

the right $ 20.00

INFORMATION LABELS

31 May 2020


R SERIES MACK CHASSIS PARTS

ALL PRICES ARE SUBJECT TO GST CHASSIS/AXLE PARTS TIE RODS - EARLY R MODEL 402 SEE B MODEL PART No 29 FOR OTHER B & EARLY R

TIE ROD OPTIONS

COVERS R MODEL DIFF 400 Single axle diff hub to hub ex R model - ratio 4.25 with springs. $ 2,000.00

DUST SHIELD SEE B MODEL AXLE/HUB/CHASSIS SECTION PART No

289 FOR OTHER SHIELD OPTIONS

R MODEL HUB CAP 3501 2958 R Series Mack hub cap. OD diameter 6 1/4 inch - Photo is

detailed for display. $ 265.00

3502 2959 R Series Mack Hub Cap. OD diameter 6 1/2 inch. Photo is

detailed for display. $ 265.00

CENTRE BEARING - EARLY R MODEL SEE PART No 284 FOR OTHER CHASSIS OPTIONS $ 927.00

CENTRE BOLT Centre bolt 12 inches (300mm) long. 1/2-inch diam, 9 inches of

thread. Suit Mack Camel Back and many other jobs. SOLD PER

EACH. SEE part no 286 for price & options.

$ 23.00

SPRING ANCHOR PINS 3509 Spring anchor pin only. 1/2 x 1 1/4. Photo includes bush. $ 46.00

SPRING BUSH 3510 Spring bush insulator only. 3 1/8 x 1 1/2. Photo includes pin. $ 49.00

R MODEL MACK CHASSIS/AXLE

31 May 2020


R SERIES MACK CHASSIS PARTS ALL PRICES ARE SUBJECT TO GST BUMPER BAR 3520 R Model standard bumper bar - black. New. Made in USA POA

3521 R Model standard bumper bar - chrome. New. Weight 25kg.

Length 2450mm, height 450mm. Flanges are 90mm. $ 2,100.00

NEW MACK BUMERS 3522 Suit new Superliner, Titan bumper, complete mounting kit with

front under protection (FUP) $ 1,000.00

BUMPS STOP SPRING SEE RUBBER PARTS SECTION PART No 2159 FOR

OTHER BUMP STOP OPTIONS

BATTERY BOX COMPLETE SEE ELECTRICAL SECTION PART No 1455 FOR OTHER

BATTERY BOX OPTIONS

ELEPHANT SPRING INSULATOR FEET SEE RUBBER PARTS SECTION PART No 2444 FOR

OTHER OPTIONS

MUD FLAPS SEE RUBBER MUDFLAPS SECTION PART No

2391 FOR OTHER OPTIONS

VENTED F U E L CAP - SUIT R MODEL SEE CAST SECTION PART No 1184 FOR FUEL CAP

OPTIONS $ 120.00


31 May 2020


R SERIES MACK CHASSIS PARTS ALL PRICES ARE SUBJECT TO GST LONG STEP FOR FUEL TANK 3542 Step Tank Mack Supply - 1500mm long $ 289.00

3543 Step Tank Mack Supply - 1560mm long $ 302.00

STEP BRACKET ANGLE MOUNTING 3545 Angle bracket for mounting above. Fuel tank steps. PRICE PER

EACH $ 22.00

3546 Bolt and nut set for above angle bracket. PRICE PER EACH. $ 3.00

3547 End Cap plate for fuel tank steps. $ 22.00

MACK R STEP - SEE CAST PARTS SEE CAST PART SECTION PART No 1165 FOR OTHER

OPTIONS

FUEL TANK J BRACKET ROLLED EDGE STRAP

SEE RUBBER SECTION PART No 2322 FOR OTHER

STRAP OPTIONS.

FRONT FUEL TANK SUPPORT RUBBERS SEE RUBBER SECTION PART No 2197 OR 2336 FOR

OTHER TANK SUPPORT RUBBERS OPTIONS.

R STEERING YOKE 3567 3088 Yoke. Steering Shaft Ross Box. (.875- inch ID) Fits onto steering

box end. $ 65.00

3568 3089 Yoke fits onto 3091 spline. $ 55.00

SHAFT 3571 3091 Shaft steering lower - suit Superliner 2 and other models. Fits

onto steering box. $ 250.00

3572 3092 Shaft steering main - suit Superliner 2 overall length 46 inches

(1070mm) as in photo that’s with 6 inch (150mm) inside yoke $ 640.00


31 May 2020


R SERIES MACK CHASSIS PARTS ALL PRICES ARE SUBJECT TO GST STEERING YOKE 3575 3093 Universal Steering Top $ 33.00

3576 3094 Universal Steering Lower. Note: There are 2 types of Lower

Unies. $ 33.00

3577 3095 Bearing Steering shaft - (Dans Superliner) 1 9 mmx52mm $ 42.00

STEERING PARTS - SHAFTS - BEARINGS 3581 30 R Bearing Steering Shaft TOP OF STEERING BOX

BRACKET. Size shaft 1-inch OD 2 inch. $ 64.00

3582 3096 R Bearing Steering Shaft Firewall. Size shaft 1-inch hole,

centres 3 1/2 inch. $ 86.00

DUST & SPLINE COVER SEE RUBBER SECTION PART No 2356 & 2357 FOR

OTHER DUST COVER OPTIONS

AIR INTAKE FITTINGS SEE RUBBER SECTION PART No 2268 FOR OTHER AIR

INTAKE OPTIONS

WATER PUMP KIT 3592 Suit most 60's & 70's Mack’s 5/8 shaft. (Note: shaft lengths do

vary with number of pulleys and front bearing sizes may vary

also)

$ 130.00

TORQUE ROD BUSHING See Axle Hub chassis part no 282 for this and other torque rod

options.


31 May 2020


R SERIES MACK ENGINE PARTS

ALL PRICES ARE SUBJECT TO GST AIR CLEANER SEALING GASKET R MODEL ENGINE MOUNTING INSULATORS 3701 2745 Mack engine mounting rubber. Fits some Flintstones, R Model,

V/Liner, Superliner, Ultraliner, Cruiseliner etc from about 70's to

around 1990's where they run 8 rear engine mounts, also used as

front engine mount on some models. Note: Very common engine

mounts. Size 80mm x 20 mm deep with 50mm wide and 18mm

high centre. Number depending on model. 8 required for most

models. 8 standard mounts. Price per each. Note: Photo shows

heavy service unit. Dimensions per piece 80mm wide x 20mm top

flange 35 overall. PA1 4670

$ 30.00

HEAVY SERVICE - Yellow Dot 3702 2747 Top harder heavy-duty rubber yellow dot used on rear top mount.

4 per truck. Price per each. 2747 $ 35.00

ENGINE INSULATOR V8 3703 Engine mount insulator V8 & Superliner 11 $ 40.00

ENGINE ID PLATES Mack engine exhaust emission control information rocker cover

plate. 200mm long x 70mm high. Supplied blank for your

detail. See Steel plate section Part No 2629 for options

ENGINE - E9 E9 ENGINE PARTS SUBJECT TO STOCK

AND AVAILABILITY. PRICE SHOWN ARE

AN INDICATION ONLY.

E 9 INLET VALVE 3710 Valve inlet 0.375 in. 400 to 610HP. Price Per Each $

105.00

E 9 EXHAUST VALVE 3711 Valve exhaust 0.375 in. 400 to 610HP. Price Per Each $

155.00

E 9 SLEEVE - ALL TO 610HP 3712 Standard engine sleeve - Price Per Each $

310.00

E 9 BEARING ROD 3713 Bearing Rod Std size. Price Per Cylinder $

125.00

SECTION R MODEL - ENGINE PARTS

31 May 2020


R SERIES MACK ENGINE PARTS ALL PRICES ARE SUBJECT TO GST E 9 PISTON 3714 Piston with CV pin Price Per Each $

592.00

E 9 RING SET 3715 Ring Set 400 & 610HP. Price Per Cylinder $

193.00

E 9 CONROD BOLT E9 865 & 866 3718 Bolt conrod 3/8 - 18 x 2.97. Price Per Each $

27.00

E9 V8 EXHAUST GASKET 3721 Gasket Exhaust E9. 3.5/8 bolt. Centres 21/2 x 2 1/2 hole. 10 Per

Set. . PER EACH $ 37.00

3722 Oil Ring Turbo Oil Drain $ 3.00

3723 Gasket Ring Exhaust - PER EACH. $ 49.00

3724 Oil Drain Gasket 1-inch hole. 2 1/16 bolt holes $ 10.00

3725 Turbo gasket. $ 33.00

3726 Oil Drain Gasket. 1/2-inch hole. 1 1/2-inch bolt holes. $ 5.00

E9 TAPPET GASKET 3727 Tappet gasket - SUIT E9. price per each $ 49.00

E 9 SUMP GASKET 3728 E9 Sump Gasket $ 90.00

E 9 AIR WATER GASKET

3729 Air and Water Gasket, Price Per Each $

49.00

E9 HEAD GASKET 3734 Head Gasket. Price Per Each $ 79.00


31 May 2020


R SERIES MACK ENGINE PARTS ALL PRICES ARE SUBJECT TO GST COOLANT CONDITIONER 3750 Coolant filter 150mm long

PRIMARY FUEL BASE 3751 Primary fuel top base. - Not Stocked

FUEL FILTER SECONDARY 3752 Secondary fuel filter 226mm long

FUEL FILTER PRIMARY 3753 Primary diesel fuel filter. 200mm long

OIL FILTER 3754 Engine Oil full flow filter. Spin on E6, E7, E9. $ 23.00

FUEL PRIMER 3760 Fuel pump hand primer. Suit E9 and Other Models. $ 180.00

MACK GENERAL MODELS (Photocopy) Workshop Manual - 937 Pages - Early - Covers Models B67-673-

70. Includes Mack C.M.B.F.R.U & Flintstone - For Engines END

465 - END 673 - ENDT 673 - ENDT673 & B - END 711 - END

864 - ENDT 864. Fuel pump, clutch, gear box, drive shaft, diffs,

came with our first new R Model Mack in 1976. See Parts Book

Section Part No 2057 for options.

RADIATOR CAP 3767 Suit most R models including 615. 10PSI. 2.625in. neck. $ 22.00

3768 IO.PSI 2.25in neck $ 24.00

RADIATOR MOUNTING INSULATOR Lower mounting 2-piece insulator V8. SEE RUBBER

SECTION PART No 2353 FOR PRICE & OPTIONS. PRICE

PER EACH


31 May 2020


R SERIES MACK ENGINE PARTS ALL PRICES ARE SUBJECT TO GST AIR STARTER 3801 Air starter motor used. Note: Pinion lengths vary. Limited Stock $ 400.00

3802 3179 Air starter valve remote valve assembly. NEW

LSV 3437 248 7/19

$

279.00

3803 3180 12V air starter solenoid control valve - to suit 3179. NEW $

206.00

WATER PUMP KIT WATER PUMP PARTS E9 V8 3819 3100 Water pump seal only, suit above kit suit 3/4 shaft 1 5/8 OD. Suit

E9. $ 60.00

3820 Water pump, complete new unit $ 1,300.00

3821 Water Pump Kit - 9 Pieces. NOTE: This kit bushes need

reaming after fitting. 10 per set. $ 550.00


31 May 2020


R MODEL - BONNET JEWELLERY

ETC.

ALL PRICES ARE SUBJECT TO GST R TYPE SQUARE BLINKER SEE ELECTRICAL SECTION PART No 1415 FOR OTHER

LIGHT OPTIONS

ROUND BLINKER SIDE AMBER SEE ELECTRICAL SECTION PART No 1423 FOR OTHER

LIGHT OPTIONS

BLINKER MOUNTING WEDGE 4104 Blinker mounting wedge - Black. $ 15.00

CHROME BLINKER MOUNTING WEDGE OPTION Blinker mounting wedge - chrome. Cast from brass and

chrome plated. See Cast Section Part No 1011 for options

4106 Blinker mounting rubber spacer. 40x7mm hole 15mm. $ 10.00

GRILLE FRONT LETTER SET - R MODEL

4110 3310 Mack letter set. Front. Suit R Bonnet & Superliner (hood).

NEW. Letter size- 5 1/2inch wide by 3 1/4 inch h igh $ 90.00

SIDE BONNET SCRIPT 4111 Mack script name - side 9inch x 3 inch. NEW. Sold Per Each. $ 60.00

CABIN FRONT LETTER SET - F MODEL 4112 Mack F letter set. Front of bonnet. New. Letter size 2 inch high

230S X 2 73 7/19

$ 98.00

BONNET BADGES - ECONODYNE 4113 3318 Econodyne Emblem - suit R Model - Price Per Each. $ 120.00

MAXIDYN

E

4114 Maxidyne Emblem - suit R Model - not stocked POA

SUPERLINE

R

4115 3321 Superliner emblem. Price per Each. NEW. $ 145.00

R MODEL - BONNET

31 May 2020


R MODEL - BONNET JEWELLERY ETC.

ALL PRICES ARE SUBJECT TO GST BONNET BADGES VALVELINE

R

4118 Valveliner Side Badge $ 145.00

DOG

EMBLEMS

SEE BULLDOGS SECTION PART No 668 FOR OTHER

DOG OPTIONS.

REPRODUCTION MODEL BADGES

SEE CAST PARTS SECTION PART No 1106 FOR

OTHER MODEL OPTIONS

BONNET

HINGE

4134 Nut 11/16, 18 thread per inch, to suit 4135 $ 17.00 4135 3268 Bonnet hinge ball type $ 75.00

4136 3269 Bonnet hinge pivot ball type. Suits R Model bonnet mount

(with front radiator mtg intercooler). 3/4 UNF thread. $ 102.00

BONNET FLARES - MACK SUPPLY 4145 R Model bonnet mudguard flares KIT.... Per Set. $ 490.00

4146 Valveliner V8 Flare Kit per set. $ 490.00

4147 Superliner Flare Kit. Per set. $ 490.00

4148 Valveliner 6 cyl mudguard flares per Set. $ 490.00

BONNET LATCH SHORT EARLY TYPE -

STEEL

BONNE

T

4167 R Model black hood latch with sq u are body - 8-inch (200mm)

pin centres. New - 4 required per truck - Note: bottom pin needs

turning for some models - sold per each - catch is extra. Square

tube section 3

1/2-inch x 90mm long

$ 82.00

AUSTRALIAN QUALITY CHROME CATCH

4168 A new catch with Australian Quality chrome. Suit Part No 4170. $ 60.00

R MODEL - BONNET

31 May 2020



ALL PRICES ARE SUBJECT TO GST BLACK

LATCH

4169 R Model black hood catch for above– NEW – Price Per Each. $ 25.00

OPTIONAL CHROME- SHORT TYPE

4170 Model R chrome hood latch with square body - new. Have been

stripped and Australian Quality Chromed. Sold per each. Note:

Catch is extra. Square tube section 3 1/2-inch x 90mm long

$ 200.00

CHROME

CATCH

4171 Model R overseas c h r o m e hood catch for above - new. Suit 4170. $ 50.00

STEEL CATCH - NOT PLATED 4172 Model R hood latch socket - NEW not painted. $ 25.00

USED BLACK LATCH SHORT TYPE 4173 Used R Model black short square - may be some rust. Used. $ 40.00

BONNET LATCH - LONG TYPE -

FIBREGLASS CHROME LONG

LATCH

4174 3296 Latch - R model chrome fibreglass hood (bonnet) 8-inch

(200mm) pin centres with adjustable length. Suit Superliner 11

& Valveliner. Sold Per Each. FHL 4646 50-65 6/19

$ 95.00

BLACK LONG LATCH 4175 3297 Latch - R Model black fibreglass hood (bonnet) 8inch (200mm)

pin centres. 2 Per Truck. Sold per Each. Square tube section 5 1/2-

inch x

140mm long.

$ 70.00

BONNET LATCH RUBBER SEE RUBBER SECTION PART No 2143 FOR OTHER

LATCH AND CATCH OPTIONS

BATTERY BOX CATCH SEE RUBBER SECTION PART NO 2102 FOR BATTERY

BOX OPTIONS

BONNET MOUNT RUBBER SEE RUBBER PARTS SECTION PART NO 2183 FOR

MODEL OPTIONS

R MODEL - BONNET

31 May 2020



ALL PRICES ARE SUBJECT TO GST R BONNET LOCATING ROLLERS 4201 Bonnet locating rollers. 3-inch diam 2 3/8 wide, 5/8 hole.

PRICE PER EACH $ 105.00

4202 Bonnet locating rollers 2 1/2 diam - PER EACH $ 40.00

BONNET LOCATING GUIDE PIN 4203 Bonnet locating taper 38mm diam x 75mm high. PRICE PER

EACH

X50QM272M 89 7/19

$ 110.00

BONNET WEAR STRIP 4205 Nylon cabin to hood wear strip. R Model. PRICE PER EACH $ 33.00

NEW GRILLE - AFTER MARKET 4210 Grille - suit F & R. Newly made from composite material and

chrome plated.

OEM CMF 519P2 TKB10208

$ 620.00

GRILL

E

4211 Grille - Suit R & F - New or Used and Reconditioned. Price

subject to quality & stock. Priced on condition. FROM

$1000

FIBREGLASS GRILLE MOULDING MOUNT 4212 New fibreglass spacer mounting for surround for Part No 4210 &

4211 $ 400.00

SUPERLINER SERIES 11 - GRILLE 4220 3281 Condenser. Full Section. $ 1,540.00

4221 3282 Grille top cap plate $ 2,385.00

4222 3283 Grille Frame L/H side $ 355.00

4223 3284 Frame R/H side $ 355.00

4224 35285 Grille Frame lower $ 275.00

NOTE: PRICES SHOWN ARE EXISTING STOCK AND

WILL CHANGE WITH US DOLLAR VALUE.

GRILLE MOULDING 4227 Grille surround moulding - black, in 2 sections. Price Per Metre. $ 4.00

GRILLE SURROUND MOULDING 4228 Grille surround moulding. Price Per Metre

STAINLESS STEEL GRILLE MOULDING 4229 Late Type R grille surround SS. Price Per Side $ 90.00

R MODEL - BONNET

31 May 2020



ALL PRICES ARE SUBJECT TO GST CHROME GRILLE MOULDING - LATE 4230 Set late RB/RD grille moulding in 3 sections 24RU516 &

245RU557 and FGM5796

HEAD

LAMP

SEE ELECTRICAL SECTION PART No 1575 FOR

OTHER HEADLIGHT OPTIONS

HEADLIGHT PANEL 4231 Headlight panel 415 long x 250 deep hole 330x205

FHP5345 MAC116QS465

HEADLIGHT TRIM 4232 Head light surround trim panel

FHP5791CQ54190A

$ 220.00

HEADLIGHT TRIM SINGLE 4233 Headlight Trim. New Stainless steel 16 5/8 long x 9 1/4 high. 7

3/8-inch hole. Price Per Each. NOTE: This type has only 2 bolt

holes and is a wee bit smaller than the 6-bolt hole one.

$ 219.00

HEADLIGHT TRIM DUAL 4235 Headlight trim new stainless steel $ 240.00

HEADLIGHT BEZEL SERIES 1 4237 Dual headlight bezel suit series 1 with round headlights $ 298.00

MACK

SUPPLY

4240 3333 Dual headlight bezel Mack Supply. Suit Superliner. 1 3/8 (35mm)

deep with mounting screws PRICE PER EACH $ 140.00

HEADLIGHT ASSEMBLY 4241 Complete oblong head light assembly RH $ 360.00

4242 Complete oblong head light assembly LH. $ 360.00

HEADLIGHT BEZEL - SUPERLINER

4243 Duel headlight bezel. Suit Superliner. 1 3/4 (45mm) deep

with mounting screws. PRICE PER EACH $ 110.00

FRONT MUD FLAP SEE RUBBER SECTION PART NO 2407 & 2408 FOR OPTIONS

RADIATOR MOUNTING INSULATOR 2738 Lower mounting 2-piece insulator V8. See Rubber Section 2353

for cost and other options.

R MODEL - BONNET

31 May 2020


R MODEL - CABIN INTERIOR

ALL PRICES ARE SUBJECT TO GST R MODEL FOOT VALVE PEDAL 4401 New brake pedal with Mack logo. Note: holes are not drilled. N/A

4402 New brake pedal with Mack logo. Cast from brass. Holes drilled

and chrome plated. N/A

THROTTLE PEDAL 4404 R Model fuel pedal only with Mack logo - New. Price Per Each. $

110.00

THROTTLE PEDAL BASE 4405 Pedal Base, Pivot Pin and Retainer Clip $ 50.00

R MODEL CLUTCH PEDAL 4407 R Model clutch pedal & bracket clutch type. Generally stocked

to change from old through floor pedal type to pendulum type

with cable. Photo shows insulation in B Model. - Used

$ 125.00

CLUTCH CABLE 4408 Suit R600 & Valveliner 109" (2770mm) 112" (2850mm) tip to

tip. $ 134.00

4409 Suit Trident, Titan, VL S/L, 138" (3480mm) long $ 144.00

SEE RUBBER SECTION PART NO 2205 FOR OTHER

RUBBER OPTIONS

DASH PANEL RH MACK SUPPLY 4411 3411 New R model genuine dash - right hand section. $ 539.00

DASH PANEL LH MACK SUPPLY 4412 3410 New R model genuine Mack dash - left hand section. Including

top hatch. $ 1,385.00

GLOVE BOX LID MACK SUPPLY 4413 3413 New genuine Mack glove box lid to suit above $ 135.00

FULL DASH BOARD - AFTER MARKET 4416 Dash assembly one piece made from fibreglass. Comes in 2

main sections, glove box lid, instrument panel, 2 top inspection

hatches. We can vinyl cover for special effect.

$ 1,135.00

DOOR & DASH SCREWS SEE CATCHES & CLIPS SECTION PART No 725 FOR

OTHER SCREW OPTIONS

CAB INTERIOR

31 May 2020


R MODEL - CABIN INTERIOR ALL PRICES ARE SUBJECT TO GST LARGE INSTRUMENT PANEL 4417 New Panel with Wood Grain finish. 12 holes cut out plus 12

switch holes. NEW PRODUCT -

ASK FOR PHOTO

SPEEDO/TACKO PANEL 4418 New Panel with wood grain finish. 2 Large holes only. NEW PRODUCT -

ASK FOR PHOTO

SMALL RH PANEL 4419 New panel with wood grain finish. No holes cut NEW PRODUCT -

ASK FOR PHOTO

SMALL BELOW PANELS 4420 Small lower panels. No holes cut.

DASH PANEL ASHTRAY 4421 New R top ashtray - black lid. $ 74.00

DASH PLUG 4422 Plug, snap lock & HLE suit 1/2-inch hole in dash panel. $ 1.00

HAND TROTTLE CABLE 4427 R Model hand throttle cable. Black knob. Length 2200mm total.

FFL 2690 078

$ 85.00

ENGINE STOP CABLE 4428 R Model engine stop cable. Red Knob. Length 2200mm titak,

FES 2680 084

$ 85.00

SPEEDO DRIVE 4429 R Model speedo cable with 2 types of adaptors -112 inch Length

3050mm $ 85.00

TACHO CABLE 4430 R Model Tacho cable with 3 types of adaptors. 88 inch

(2240mm long.) $ 85.00

SPEEDO DRIVE 4433 Speedo gear box drive 3 1/2 inches long - square. $ 40.00

CAB INTERIOR

31 May 2020


R MODEL - CABIN INTERIOR ALL PRICES ARE SUBJECT TO GST USA SUPPLIED GAUGES SPEEDO SEE ELECTRICAL SECTION PART No 1515 FOR OTHER

GAUGE OPTIONS.

GEAR SHIFT& STEERING BOOT SEE RUBBER SECTION PART NO 2345 FOR OTHER

BOOT OPTIONS

HEATER DUCT Round heater duct vents - suit R Model 4437 Oblong ball heater duct vents 65mm diam. Suit 60mm hole -

suit R Model. $ 68.00

RECTANGULAR VENTS 4438 Rectangular louvre duct vents. 6 inches longs & 1 3/4 inches

wide. $ 50.00

LIGHT OPTIONS SEE ELECTRICAL SECTION PART No 1620 FOR OTHER

LIGHT OPTIONS

HEATER KNOB 4441 Heater control knob $ 35.00

HEAT/AIR CONDITIONER PANEL 4442 Clear heat and air conditioner panel $ 60.00

KICK PLATES 4452 R Model Entry Kick Plate. Custom to fit around corners with

printing of your choice. Polished Stainless Steel. Have Mack cut

out on front and Superliner 11 etching on top. Other words on

request. Ask for Larger Photo.

$ 180.00

4453 3415 R Door entry stainless steel kick plates with Mack logo and

special clear hard coat. Price Per Each. $ 70.00

FRONT FLOOR MAT SEE RUBBER SECTION PART No 2305 FOR OTHER MAT

OPTIONS

CUSTOM HORN BUTTON LOGO SEE LABELS SECTION PART No 2874 FOR OTHER

LABEL OPTIONS

CAB INTERIOR

31 May 2020


R MODEL - CABIN INTERIOR ALL PRICES ARE SUBJECT TO GST STEERING WHEEL Mack optional upgrade. 18 inch 4 spoke steering wheel. See

Dress Up Parts - Part No 1281 for pricing. POA

4471 Steering wheel hub for above to suit R model standard steering

shaft. POA

HORN BUTTON 4474 Horn button with Mack logo. $ 68.00

4475 Horn Button - tan - with 3 mounting legs $ 115.00

4476

HORN BASE PLATE 4477

4478

HORN CONTACT 4479

HORN SPRING 4480

22 INCH BEIGE STEERING WHEEL 4481

LATE HORN BUTTON 4483 Late Horn Button Kit $ 145.00

SEE LABELS SECTION PART No 2886 FOR OTHER

LABEL OPTIONS

SUN VISOR 4495 Early type sunviser made from fibre glass $ 526.00

CAB INTERIOR

31 May 2020


R MODEL - CABIN INTERIOR ALL PRICES ARE SUBJECT TO GST WESTERN TRIM 4501 Tylden offer a full R Model Western Trim package as per factory

with large facing dogs or diamonds hot welded into material or

optional stitched with loose buttons. Available in brown, cream,

grey, magnum (red), or colour of your choice.

Western Trim including 2 seats (part No 4502), 2 Door trims

(Part No 4505), Set of arm rests (Part No 4508 ), Rear Cab

(Part No 4510) and Hood Lining (Part No 4517). 2 Pillar

Trims. Trim Buttons.

NOTE: ALL PRICES SHOWN ARE FOR UPHOLSTERY

ONLY.

$ 3,000.00

SEAT

4502 Bucket Seat Cushion, original perforated vinyl with Mack Logo

stamp in back (as original). Price Per Each. Ask us to email

better photos.

$ 425.00

DOOR TRIM 4505 R Model Western door trim with welded dog logo. Original

welded patterns or stitched with buttons. Price Per Each. Ask us

to email better photos and options.

$ 280.00

2 PIECE DOOR TRIM OPTION 4506 OPTION 1 - Top Section $ 210.00

4507 OPTION 2 - Lower Carpet Section $ 60.00

CAB INTERIOR

31 May 2020


R MODEL - CABIN INTERIOR ALL PRICES ARE SUBJECT TO GST ARM REST 4508 R Model door arm rest. Price Per Set. Ask us to email better

photos. $ 70.00

REAR CAB LINING 4510 R Model Rear Full Cab lining Western original pattern in

perforated vinyl.

Ask us to email better quality photos.

$ 680.00

LOWET REAR LINING OPTION 4513 R Model rear lower cab lining with welded original lines. Ask us

to email better quality photos. $ 580.00

ROOF LINING 4517 R Model roof head lining in perforated vinyl.

Ask us to email better quality photos $ 700.00

ALL NEW FLOOR CONSOLE 4520 R Model centre floor console in vinyl, base & lid. - trim only.

Box supplied by Customer. $ 190.00

4521 Steel centre console base only, 390mm x300mm deep x 280

wide with timber lid. $ 158.00

UPHOLSTERY HOLDING BUTTONS SEE CATCHES & CLIPS SECTION PART No 961 FOR

OTHER BUTTON OPTIONS

ROOF CONSOLE TRIM 4524 R Model front roof console. Cover Only. (console supplied by

customer) Len g t h 1400x250x100 $ 130.00

4525 New R front roof console with corner pieces made from

aluminium. See above for cover. $ 320.00

ROOF CONSOLE MOULDED 4526 New front console moulded with hatch surround.

Cover in vinyl with stitched edging - add $190.00 $ 600.00

ROOF HATCH SURROUND 4528 R Model hatch surround. Cover Only $ 65.00

4529 New inner R hatch ventilator surround made from steel to shape

of original plastic (Not Covered) $ 180.00

CAB INTERIOR

31 May 2020


R MODEL - CABIN INTERIOR ALL PRICES ARE SUBJECT TO GST DOOR PILLAR 4532 R Model Side front pillar trims - L & R at top of photo.

Centre of photo shows door arm rests.

Bottom photo are angles to hold roof console.

$ 110.00

CABIN SIDE SHUTTLE BOARD 4534 Cabin side kick infill same colour as lower door trim. Per Pair. $ 130.00

MACK AIR ACTUATORY 4545 Mack red dot part no 4379-RD554144. Used to open and close

air vent shutters. Suit DM/R/RB/RD/RW Models. $ 60.00

VENT SHUTTERS 4647 Air cylinder open and closed vent shutters. Suit

DM/R/RB/RD/RW models.

SLEEPER LIFT UP HATCH See Dress Up Parts for Hatch. Part No 1221 for Costs and

Options.

CAB INTERIOR

31 May 2020


R MODEL CABIN EXTERIOR

ALL PRICES ARE SUBJECT TO GST 48" MACK SLEEPER EXCHANGE 4700 Mack extended to 48-inch contour back fibreglass sleeper

designed to accommodate front trailer in many cases without

extending truck wheel base. Large enough for single bed mattress,

twin exhaust cut outs. Cost starting from $10,000 with exchange of

your flatback or contour existing sleeper.

R AIR CLEANER - USED 4701 Used RH Mack air cleaner 15-inch OD (sample

photo) (SUBJECT TO STOCK AVAILABLE) POA

R AIR CLEANER - NEW 4702 New look-a-like reproduction air cleaner. Made from NON-

RUST fibre glass. Ask us to send photos (sample photo). $ 1,350.00

AIR CLEAN WRAP 4703 Stainless Steel Wrap Around to suit above air cleaner part 4702 POA

AIR FILTER ELEMENT 4705 Air Cleaner Element - Suit Mack R & ValveLiner $ 99.00

TOP

GASKET

4706 Top Lid Gasket - Suit R and Valveliner. 380 OD. 12 Holes

CTPF233125545 15-79 5/19

$ 28.00

AIR CLEANER TOP HAT NUTS 4707 Air Cleaner Top Hat Nuts.

FNU 0189 2191-P119325 3.85 7/19

$ 5.00

AIR CLEANER SERVICE INSTRUCTIONS - R

MODEL

SEE LABEL SECTION PART No 2701 FOR OTHER

LABEL OPTIONS

AIR CLEANER HAT 4712 Air cleaner hat - black plastic 15in x 3 1/2 plus sprig it extra 1

1/2 ins rain. Suit pipe size 6 inch. $ 150.00

4713 Air ram 6 inch with side vents $ 220.00

AIR CLEANER BRACKET KIT 4716 Left hand air cleaner bracket. All Section cut out ready for

assembly. As fitted to a 1982 Superliner. Photo includes assembly

and painting.

MKX7MD58E

POA

CAB LEVELLING VALVE 4734 3467 Valve cab levelling suit R Model and also T401 Kw. $ 190.00


31 May 2020


R MODEL CABIN EXERIOR

ALL PRICES ARE SUBJECT TO GST CABIN SUPER CUSHION AIR BAG 4735 Cabin rear air spring bag. Max inflation 100 PSI. Max Torque

15ft lbs. Length 5 1/4 inch. Diameter at big end - 3 1/2 inch $ 110.00

CAB SHOCK ABSORBERS 4736 Cab shocker 2 7 0 mm long 50 mm diam. Pin hole 1/2 inch $ 120.00

CAB ENTRY GRAB HANDLE 4745R Grab entry handles. 610-hole centres. Price Per Each. $ 70.00

CABIN INSULATORS SEE RUBBER SECTION PART No 2197 FOR OTHER

INSULATOR OPTIONS $ 28.00

LH ROOF GUTTER 4747 LH Roof gutter and top door header assembly. ASK RE OPTIONS $ 400.00

CAB RH ROOF GUTTER 4748 RH Roof Gutter and top door header assembly. ASK RE OPTIONS $ 400.00

FRONT CORNER POSTS 4749 Front Cab Corner Posts POA

FIREWALL PLATE SEE STEEL PLATES SECTION PART No 2634 FOR

OTHER ID PLATE OPTIONS

CABIN ROOF TURRET 4759 R Model late cab top roof pressing without hole $ 1,450.00

CABIN TOP ROOF VENT 4762 R type Cabin top roof ventilator cowl outer assembly

25153840 231 5HA

$ 270.00

R MODEL CABIN ROOF VENT SEAL 4763 3420 Roof Vent Seal. 37 INCHES (940mm)

FSV 3775

$ 45.00

CABIN SIDE

VENT

4765 3811 Side Vent Cover Door. $ 168.00


31 May 2020


R MODEL CABIN EXTERIOR ALL PRICES ARE SUBJECT TO GST SIDE CABIN AIR VENT RUBBER SEE RUBBER SECTION PART No 2459 FOR OTHER

SEAL OPTIONS

R MODEL FRONT VENT COWL ASSEMBLY 4769 Front cabin vent cowl assembly. Complete, ready for assemble.

(has rod assembly but no control). $ 370.00

SLEEPER TO CAB SEAL SEE RUBBER SECTION PART No 2420 FOR OTHER

SEAL OPTIONS

WINDSCREEN GLASS 4772 Windscreen glass LH, suit R. valve, super, metro. Weight 10

Kg. 31 inches (800mm) x 21 inches (530mm). Australian

Approved Stamp.

$ 180.00

4773 Windscreen glass RH, suit R, valve, super, metro. Weight

dimension as

LH. Australian Approved Stamp.

$ 180.00

R MODEL WINDSCREEN RUBBER 4774 3418 Windscreen rubber - complete both sides. $ 230.00

REAR

WINDOW

4776 Suit R & F C/liner & MCR Mod el rear window - laminated.

Tinted Std. Auto glass. Australian Approved Stamped. Weight 8

Kg. Length

1100mm Height 450mm

$ 170.00

REAR WINDOW SEAL Rear window glass rubber seal. See Part No

2520. Supplied with lock strip.

See rubber section part No 2523 for other options.

WINDSCREEN WASHER BOTTLE 4784 3449 Reservoir windscreen washer bottle cap & pump. 12V. R model

door. $ 139.00

4785 3492 Plug with wiring harness for windscreen washer bottle. $ 69.00

4786 3493 Washer bottle cap only.

25153013 7-90 7/19

$ 16.00

WINDSCREEN BOTTLE PUMP 4787 3494 Washer bottle pump. 12V.

9823-1000010 57-50 7/19

$ 65.00

NOZZLE SUPPLY FITTING 4788 3488 Cab fitting nozzle assembly 5/16 - 24 for inbuilt wiper nozzle.

SOLD PER EACH.

25080442 69 7/19

$ 75.00


31 May 2020


R MODEL CABIN EXTERIOR ALL PRICES ARE SUBJECT TO GST R MODEL WIPER ARMS 4790 3495 LH wiper arm with inbuilt concealed windshield washer nozzles

& two knurled drive options. $ 130.00

4791 3496 RH Wiper arm with inbuilt concealed windshield washer nozzle

and two knurled drive options. $ 130.00

R MODEL WIPER BLADE 4792 3497 Windscreen wiper blade. R Model. 16 inch long. $ 40.00

F MODEL WIPER BLADE 4793 3489 Windscreen wiper blade - F Model - 20 inch long (500mm) $ 60.00

KNURLED

DRIVE

4794 3486 Knurled drive tapper spline on OD rectangular hole centre adapter

wiper arm - new - 2 required - sold per each. $ 14.00

ACORN DOMED NUT 4795 3485 Domed nut wiper blade drive

25056069 8/27 7/19

$ 12.00

R MODEL WIPER PIVOT BODY 4796 3490 RH Pivot body and complete connecting arm assembly with end

bearing for connection to wiper motor. $ 243.00

4797 3491 LH Pivot body and complete c o n n e c t i n g arm assembly with

end bearing for connection to wiper motor $ 243.00

AIR WIPER MOTOR 4798 3487 New Air wiper motor assembly. Note: this requires a new

valve see below. $ 429.00

VA

LV

E

4799 3488 New Valve port control assembly for above 3 port (3487) h a s side

screw air wiper motor. Bin 3488. Note: B Model has 4 Ports. $ 125.00

UNIVERSAL AIR WIPER MOTOR 4800 Air wiper motor with remote control. Universal, suit many

applications including R Model, Supplied with long rod for

remote control. Control pipes location optional. Can be extended

if required for some applications. Mack 63QT411 FMT4821

$ 700.00


31 May 2020


R MODEL CABIN EXTERIOR ALL PRICES ARE SUBJECT TO GST R MODEL MACK SUPPLY ELECTRIC WIPER

MOTOR

CONVERSION

KIT

4805 Bolt 1/2 x 1/4 & Washer $ 0.95

4806 3474 Wiper Motor Assembly Etc. $ 212.00

4807 3475 Link Assy LH- without shaft $ 118.00

4808 3476 Linkage Wiper without shaft $ 230.00

4809 Screw & Washer (4 required each) $ 2.15

4810 3478 Arm wiper elec small shaft RH $ 125.00

4811 3479 Arm Wiper elec small shaft LH

25109820 100 $ 125.00

4812 3480 Wiper blades - 18-inch (450mm) suit 3478 & 3479 - 2 required

PRICE PER EACH.

8515033720 7/19

$ 39.00

4813 3481 Breaker Circuit $ 34.00

4814 3482 Switch elec W. Per control. $ 210.00

4815 3483 Harness wiring for wiper conversion.

25497684 213 7/19

$ 240.00

4816 3481 Knob Wiper Switch. Note: has side screw. $ 27.00

KIT ITEMS AS SHOWN...

COST

$ 1,310.10

WIPER KNOB PUSH ON 4817 Wiper knob - Push

ELECTRIC WIPER MOTOR 4818 Mack R/RD electronic wiper motor. After Market Type.

FMT5455 156 7/19 63QT310

EM54550

$ 200.00


31 May 2020


R MODEL - DOORS ALL PRICES ARE SUBJECT TO GST 5001 3500 Door shell - R Model - new Left - suits 79 onwards (take the

lock with 2 bolt striker) door locks. Weight 20Kg. Height

1400mm x

860 x 140.

$ 1,150.00

5002 3501 Door shell - R Model. New right. Sit 79 onwards (take the lock

with 2 bolt sticker) door locks. NOTE: also fits early R cabins

but holes may vary.

$ 1,150.00

DOOR LOCK RETAINER CLIP SEE CATCHES, LOCKS & CLIPS SECTION PART No 755

FOR OTHER CLIP OPTIONS

BAILEY CHANNEL - R & F SEE RUBBER SECTION PART No 2114 FOR

OTHER CHANNEL OPTIONS

$ 70.00

DOOR ENTRY HANDLE 5005 3523 R door handle. Outer R & F model cab.

FHD4491 62 7/19

$ 85.00

INNER DOOR HANDLE - LATE 5006 3522 R Model door handle late - inner R & F after 1979 with thicker

Western trim.

FHD4492 58 7/19

$ 80.00

INNER DOOR HANDLE - EARLY 5007 3524 R door handle inner (Suit B) R & F pre 79 NOTE: Part no.

5006 has better clearance with no trim. $ 80.00

WINDOW REGULATOR HANDLE - LATE 5008 3531 Window regulator handle. Suit doors with Western Trim or worn

Shafts. $ 80.00

WINDOW REGULATOR HANDLE - EARLY 5009 Window regulator handle, early B, R&F. Pre 79 Par No 5008

above has better clearance if fitting door trims or worn shafts

etc.

FHD4480 41-30 7/19

$ 65.00

DOOR HANDLE ESCUTCHEON 3528 SEE CATCHES, LOCKS & CLIP SECTION PART No 775

& FOR OTHER DOOR OPTIONS

R DOOR HANDLE 5012 R Model door pull handle. Suit R, RB, RD, DM, MC, MR & LE.

55Q53930301RP2

803 938 76 6/19

$ 90.00

R MODEL DOOR GLASS 5017 3330 Door glass R & L. Note: We supply 6mm green tinted

toughened auto glass. Stamped to Australian Standards. $ 110.00

R MODEL - DOORS

31 May 2020


SECTION - R MODEL - DOORS ALL PRICES ARE SUBJECT TO GST LATE MODEL WINDOW SUPPORT 5018 353 Support window RH model. Used with Part 5053 - 450mm long. $ 90.00

5019 3536 Support window LH model. Used with Part 5052. 450mm long.

FWS4699 64 7/19 31QX411

$ 90.00

EARLY WINDOW SUPPORT 5020 3567 Support channel for door glass regulator for passenger RHside

roll up window glass 400mm long. Used with Part 5035 & 5036.

Suit early styled cabs.

$ 75.00

5021 3566 Support channel for door glass regulator for driver side LH roll

up window glass 400mm long. Suit early styled cabs. $ 75.00

DOOR HINGE. RH 5024 3509 Door hinge RH. $ 190.00

DOOR HINGE. LH. 5025 Door Hinge LH $ 190.00

DOOR LATCH AFTER 1979 R & F 5027 3542 Latch door late RH. Used with part no. 5054. Mack current style

DM, R, RB, RD. $ 95.00

5028 3543 Latch door- late LH. Used with part no. 5054. Mack current style

DM, R, RB, RD. $ 95.00

DOOR LATCH EARLY TO 1979 5029 3553 Latch door early RH, suit R & F, MIR, MBR. Seems also to suit

White Road Commander. $ 130.00

5030 3554 Latch door - early LH. Suit R & F, MIR, MBR. $ 130.00

DOOR LATCH SCREWS 3517 Door latch holding screws. 3 Per Door - 1/4 inch. PRICE

PER EACH. Note: The original screws are an oddbod size

and you need to tap our your locks 1/4 UNC. SEE Catches,

Locks & Clips

Part No 720 for details and options.

DOOR LATCH STRIKER - LATE R & F. 5034 3559 Striker Plate RH - used with part no. 5027. Mack current style

R, RB, RD, DM. Screws not included. $ 50.00

DOOR LATCH STRIKER - LATE R & F 5035 3560 Striker Plate LH. used with part no. 5028. Mack current style

R, RB, RD, DM. Screws not included. $ 50.00

R MODEL - DOORS

31 May 2020


SECTION - R MODEL - DOORS ALL PRICES ARE SUBJECT TO GST DOOR LATCH STRIKER - EARLY R & F 5036 3555 Striker Plate - RH. Mack early style R, RB, RD, DM.

NOTE: Also suits White Road Commander. FXD4691 61-

62 7/19

$ 100.00

5037 3556 Striker Plate - LH. Mack early style R, RB, RD, DM. $ 100.00

KEY DOOR LOCKS SEE ELECTRICAL SECTION PART No 1610 FOR

OTHER SWITCH OPTIONS

DOOR MIRROR ARMS 5040 3575 Kit mirror bracket RH stainless. $ 250.00

5041 3576 Kit mirror bracket LH stainless. $ 250.00

DOOR MIRROR HEAD 5042 3577 Mirror head-Mack. LH alloy type with bulldog but no heating

or light. $ 260.00

5043 3578 Mirror head-Mack. RH alloy type with bulldog but no heating

or light. $ 260.00

DOOR INNER PANEL 5047 3506 Door inner panel RH suit late model. Bare - NEW. Seems

the same as early R door but some holes are different. $ 250.00

5048 3507 Door inner panel LH suit late model. Bare. New

FDP5787 228 7/19 FDP 5792 228 7/19

$ 250.00

DOOR PANEL SCREWS 3516 SEE CATCHES, LOCKS & CLIPS SECTION PART No 725

FOR OTHER SCREW OPTIONS

LATE MODEL WINDOW REGULATOR 5052 3538 Regulator assembly LH. (Later model - post 83) $ 140.00

5053 3539 Regulator assembly RH. (Later model - post 83). $ 140.00

LATE MODEL WINDOW REGULATOR 5054 3545 Linkage remote door. Connects handle to door lock. Used

with part No 5052 & 5053 $ 70.00

R MODEL EARLY WINDOW REGULATOR 5055 89 Window regulator scissors - Left. Suit early R style cabs. $ 185.00

5056 90 Window regulator scissors - Right. Suit early R style cabs. $ 160.00

R MODEL - DOORS

31 May 2020


SECTION - R MODEL - DOORS ALL PRICES ARE SUBJECT TO GST R MODEL EARLY REGULATOR GEAR PLATE 5057 914 Gear plate for passenger LH side door regulator. Suit early

style cabs. See Part 760 for retaining ring

FWR 4700 85 7/19

$ 120.00

5058 91R Gear plate for driver RH side door regulator. Suit early styled

cabs. Even No = R side. See Part No 760 for retaining

ring.

$ 120.00

DOOR REGULATOR SCREWS 3541 SEE CATCHES, LOCKS & CLIPS SECTION PART No 560

FOR OTHER CLIP OPTIONS

RETAINING RING 3540 SEE CATCHES, LOCKS & CLIPS PART No 760 FOR

OTHER CLIP OPTIONS

GEAR PLATE RING 2920 SEE CATCHES, LOCKS & CLIPS SECTION PART No 765

FOR OTHER CLIPS OPTIONS

WINDOW WEATHER STRIP WITH RUBBER

SEAL

3546 SEE RUBBER SECTION PART No 1896 FOR

OTHER SQUEEGEE OPTIONS

DOOR

SEAL

2559 SEE RUBBER SECTION PART No 2211 FOR OTHER

SEAL OPTIONS

VENT

WINDOW

5062 3528 Vent window flipper LH. (Quarter Vent), Suit models R &

F. Have clear glass. $ 300.00

5063 3529 Vent window flipper RH. (Quarter Vent). Suit models R & F.

Has clear glass. $ 300.00

GENUINE MACK SUPPLY 5064 3532 R & F model vent window flipper (quarter vent). LH only.

Have light tint glass. $ 410.00

5065 3533 R &F model vent window flipper (quarter vent). RH only.

Have light tint glass. $ 410.00

QUARTER VENT GLASS 5066 3534 R & F quarter vent replacement bevelled tempered 6mm auto

glass with Australian Standard stamp. Price Per Each. Note:

The replacement is tinted.

$ 120.00

GENUINE MACK SUPPLY 5069 3571 R & F Model vent window flipper (quarter vent) outer rubber

seal

LH only

$ 120.00

5070 3572 R & F Model vent window flipper (quarter vent) outer rubber

seal

RH only

$ 120.00

R MODEL - DOORS

TYLDEN HERITAGE MAIL ORDER PARTS CATALOGUE...S eRubb rP a ts ec ti onp rt 2260 f m un g d h options....

Documents

Transcript of TYLDEN HERITAGE MAIL ORDER PARTS CATALOGUE...S eRubb rP a ts ec ti onp rt 2260 f m un g d h options....