Twist drills 10 - p-alians.ru · • Twist drills • Miniature drills ... HHW Grundlayout 2008...

1

eng/OP

10

11

12

13

14

15

16

17

18

19

10.3 – 10.46

11.1 – 11.28

12.1 – 12.10

13.1 – 13.14

14.1 – 14.66

15.1 – 15.4

16.1 – 16.74

17.1 – 17.44

18.1 – 18.96

19.1 – 19.10

• Round dies

Cutting• Twist drills • Miniature drills • Sheet metal drills• Core drills • Step drills • Centring and spot drills • Taper pin drills

• Solid carbide drills • Solid carbide tapping Tools • Carbide reversible cutting inserts • Twist drills with reversible

cutting inserts • Masonry drills • Impact drills • Drill bits for socket outlets

• Countersink and deburring tools

• Countersinks and deburrers• WPL-Countersinks• Counterbores• Spot facing cutters

• Hand Reamers • Taper Reamers• Helical taper pin reamers• Taper structural reamers• Chucking reamers• Automatic machine reamers• Clamp-on reamers• Jet reamers

• Taps and thread moulders • Solid carbide thread milling cutters• Thread repair sets • SC thread boring tools• Tap extractors • Arc erosion machines • Tap and die sets

• HSS/HSS-E-milling cutters• Solid carbide milling cutters• Form end milling cutters• Broaches

• Sawblades and inserts• Milling cutters • WPL milling cutters• Reversible cutting inserts• Core drills and countersinking

cutters • Profile milling cutters• Milling arbors

• Round tool bits • Parting off and Grooving tools • Threading tools• Tool bits and chisels • Clip holders • Boring bars • Reversible cutting inserts • Knurling tools

• Circle cutters• Coolant tubes • Lubricants and concentrates• Emulsion mixers • Refractometers • Thread tallow • Protective shields • Chiphooks and scissors

1

10_HHW_Katalog_2009_EN:HHW Grundlayout 2008 12.01.2011 9:53 Uhr Seite 10.1

eng/OP

TiN TiCN TiAlN TiAlN-TiN(Titanium-Nitride) (Titanium-Carbon-Nitride) (Titanium-Aluminium-Nitride)

Balinit® A Balinit® B Balinit® FUTURA Balinit® X.TREME HHW TOPFIRE

Properties multi-purpose use high hardness, high heat hardness, high hardness, high hardness,standard coating good ductility oxide resistance chemical stability chemical stability

Application steel cutting for tools with high for tools with high for HSS and for HSS and carbide-mechanical stress high thermal stress; carbide drilling tools drilling tools

drilling, turning, dry working hard materials and HSC

Hardness 2.300 HV 3.000 HV 3.000 HV 3.500 HV 3.600 HV

Max. operation 600°C 400°C 800°C 800°C 800°Ctemperature

Coating structure single-layer multi-layer multi-layer single-layer multi-layer

Coating colour gold-yellow blue grey violet-grey violet-grey red-violet

Our suppliers for catalogue-group 1:

Advantages:• Longer service life• Higher productivity• Less tool exchange

• No emulsion needed due to dry milling• High-speed and hard-working

0

ß

E

eromobil®

Y

)

P

T

:

F

*

+

Coatings for cutting tools


The HHW colour-coding system

The HHW colour-coding system enables you to see at once which tool is suitable for which material. In most sections of the catalogue, HHW provides you with additional information and data for the respective tool.

The HHW colour-coding system is structured logically and in accordance with the steel key system.

This means, you can choose your tools before the start of the project and therefore you will save time and money.

www.hhw.de 10.3

1

eng/OP

HSS-ETiAIN

VA

Al<10%Si Al>10%Si Cu St<520N St<750N St<900N St<1100N St<1200N St<1400N <45HRC <55HRC <60HRC <67HRC VA-steel<900N VA-steel>900N Ti GG(G) plastics45-110 45-110 - 26-60 25-60 20-50 15-35 15-35 10-30 - - - - 15-40 15-40 - 20-60 -

900N VA-steel>900N0 15-40

Operating direction = No centre cut, face milling only above workpiece edge

= With centre cut, recessing and face milling possible (in 3 directions)

Type of thread e.g. = Metric Fine thread

Quality e.g. = High-performance high-Speed-Steel with cobalt (E) alloy and Titanium-Aluminium-Nitrite coating

Type of shank = Straight shank with driving face in compliance with DIN 1835 B

= Straight shank with draw-in thread in compliance with DIN 1835 D

= Straight shank smooth in compliance with DIN 6535 HA (for solid carbide tools)

= Straight shank with driving face in compliance with DIN 6535 HB (for solid carbide tools)

Spiral flute angle e.g. = Spiral flute angle of the tools approx. 39° clockwise

e.g. = Spiral flute angle of the tools approx. 12° counterclockwise

Point angle e.g. = Point angle of the cutting blades 120°

Tolerance e.g. = Tolerance of cutting blades in compliance with ISO-recommendation R286-1962

Type description e.g. = For standard-duty materials

Material strength e.g. = For materials with a strength of up to max 1000 N/mm2

e.g. = For materials with a strength above 900 N/mm2

Most suitable for … = Aluminium

= Grey cast iron

= Brass

= Multi-purpose use

= Corrosion, acid and heat-resistant and austenite steel (V2A, V4A)

Pictograph Overview

carbide/coated coated


Manufacturer 0 0 0 T T T 0 T ß 0

Standard/DIN 338 338 338 338 338 338 338 1899 1897 1897

Type short short short short short short short Mini extra short extra shortItem number 10047 10050 10053 10210 10211 10214 10215 10220 10250 10252Material HSS-Co8 HSS-E HSS-E HSS HSS HSS-E PM HSS-E HSS HSSDiameters mm 1 - 13 1 - 13 1 - 12 0,5 - 14 0,5 - 16 1 - 12 1 - 14 0,15 - 1,45 2,5 - 5 1 - 25Type N FS FS H W VA X-DRILL N N NPoint angle 135° 130° 130° 118° 130° 130° 130° 118° 118° 118°Coating – – TiN – – – TiN – – –Page in catalogue 10.12 10.13 10.13 10.15 10.15 10.15 10.17 10.18 10.18 10.19

SuitabilityAluminium < 10% Si X X W X X X X XAluminium > 10% Si X X W X X X X XCopper X X W X X X X XBrass WSteel < 520N W W W W W W WSteel < 750N W W W W W W WSteel < 900N W W W W W W WSteel < 1100N W W W W WSteel < 1200N W W W WSteel < 1400N W W W WVA-steel < 900N W W W W WVA-steel > 900N W W W W WGG W W W WGGG W W W WTitanium X XTitanium alloys XNickel X< 55HRC< 60HRC< 67HRCPlastics X X X X X X X

Manufacturer 0 0 ß 0 0 ß 0 0 0

Standard/DIN 338 338 338 338 338 338 338 338 338 338

Type short short recessed short short rolled short short MBS short short short shortItem number 10001 10002 10003 10010 10020 10035 10040 10042 10044 10046 Material HSS HSS HSS HSS HSS HSS-E HSS-E HSS-E HSS-E HSS-EDiameters mm 0,3 - 20 13,5 - 20 0,3 - 16 0,3 - 16 1 - 16 1 - 13 0,3 - 16 0,5 - 16 1 - 12 1 - 13Type N N N N N UNI N Ti N VAPoint angle 118° 118° 118° 118° 118° 118° 118° 130° 130° 130°Coating – – – – TiN – – – TiAlN –Page in catalogue 10.6 10.7 10.8 10.8 10.9 10.9 10.10 10.11 10.11 10.11

SuitabilityAluminium < 10% Si X X X X X W X XAluminium > 10% Si X X X X X W X XCopper X X X X X W X XBrassSteel < 520N W W W W W W W W WSteel < 750N W W W W W W W W WSteel < 900N W W W W W W W W WSteel < 1100N W W W W WSteel < 1200N W W W WSteel < 1400N W W WVA-steel < 900N W W W WVA-steel > 900N W W WGG W W W W W W WGGG W W W W W W WTitanium WTitanium alloys WNickel W< 55HRC< 60HRC< 67HRCPlastics X X X X X W X

1

eng/OPwww.hhw.de10.4

Twist Drills Overview

W = suitable X = partially suitable



Manufacturer T T 0 T 0 0 T TStandard/DIN 1869 1869 345 345 345 345 341 341 1870 343

Type extra long extra long MT shank short MT shank short MT shank short MT shank short long MT shank long extra long Z3Item number 10421 10422 10508 10510 10511 10514 10526 10610 10621 10632Material HSS HSS HSS HSS HSS HSS-E HSS-E HSS HSS HSSDiameters mm 2 - 12 2 - 11 5 - 60 10 - 50 10 - 26 10 - 35 11 - 32 10 - 35 8 - 30 7,8 - 30Type FN FN N N N N VA N FN NPoint angle 130° 130° 118° 118° 118° 118° 130° 118° 130° 120°Coating – TiN – – TiN – – – – –Page in catalogue 10.25 10.25 10.26 10.26 10.27 10.27 10.27 10.28 10.28 10.29

SuitabilityAluminium < 10% Si X X X X X XAluminium > 10% Si X X X X XCopper X X X X XBrassSteel < 520N W W W W W W W W W WSteel < 750N W W W W W W W W W WSteel < 900N W W W W W W W W W WSteel < 1100N W W W W WSteel < 1200N W WSteel < 1400N WVA-steel < 900N W W WVA-steel > 900N WGG W W W W W W W W WGGG W W W W W W W W WTitanium XTitanium alloys XNickel X< 55HRC< 60HRC< 67HRCPlastics X X

Manufacturer 0 0 0 0 0 0 ß T 0

Standard/DIN 1897 1897 1897 1897 1897 340 340 340 340 340

Type extra short extra short extra short MBS extra short extra short long long long long longItem number 10255 10257 10259 10260 10261 10404 10406 10407 10408 10410 Material HSS-E HSS-E HSS-E HSS-E PM HSS-E HSS HSS HSS HSSDiameters mm 1 - 13 1 - 20 1 - 14 1 - 20 1 - 14 1 - 12 0,6 - 16 1 - 13 2 - 10 1 - 12Type VA N UNI VA X-Drill VA N FS FW FNPoint angle 130° 130° 130° 130° 130° 130° 118° 130° 130° 130°Coating TiN – – TiAlN TiN – – – – TiNPage in catalogue 10.19 10.19 10.20 10.21 10.22 10.23 10.23 10.24 10.24 10.25

SuitabilityAluminium < 10% Si X X X X W W XAluminium > 10% Si X X X X W W XCopper X X X X W X W XBrassSteel < 520N W W W W W W W W WSteel < 750N W W W W W W W WSteel < 900N W W W W W W W WSteel < 1100N W W W W W W WSteel < 1200N W W W WSteel < 1400N W W WVA-steel < 900N W W W W WVA-steel > 900N W W W W WGG W W W W W W W WGGG W W W W W W W WTitanium W XTitanium alloys XNickel X< 55HRC< 60HRC< 67HRCPlastics X X W

1

eng/OP www.hhw.de 10.5




www.hhw.de10.6

1

eng/OP

Short Twist Drills

0Type Straight shank, right-hand cut, relieved cone grind.Starting at 1 mm, with web-thinned chisel edge.QualityHSS ground for steel up to 900 mm2.

Note: Quality drill to satisfy the highest requirements.

10001

HSS groundd1 h8 l2 l1 10001 …

mm mm mm a0,3 3 19 10 pcs. 609

0,35 4 19 10 pcs. 6130,4 5 20 10 pcs. 618

0,45 5 20 10 pcs. 6220,5 6 22 10 pcs. 626

0,55 7 24 10 pcs. 6300,6 7 24 10 pcs. 635

0,65 8 26 10 pcs. 6400,7 9 28 10 pcs. 644

0,75 10 30 10 pcs. 6490,8 10 30 10 pcs. 654

0,85 10 30 10 pcs. 6590,9 11 32 10 pcs. 663

0,95 11 32 10 pcs. 6671,0 12 34 10 pcs. 6721,1 14 36 10 pcs. 6791,2 16 38 10 pcs. 6881,3 16 38 10 pcs. 6971,4 18 40 10 pcs. 6991,5 18 40 10 pcs. 7041,6 20 43 10 pcs. 7121,7 20 43 10 pcs. 717

1,75 22 46 10 pcs. 7211,8 22 46 10 pcs. 7241,9 22 46 10 pcs. 730

1,95 24 49 10 pcs. 7342,0 24 49 10 pcs. 737

2,05 24 49 10 pcs. 7402,1 24 49 10 pcs. 7412,2 27 53 10 pcs. 7432,3 27 53 10 pcs. 7452,4 30 57 10 pcs. 7502,5 30 57 10 pcs. 7532,6 30 57 10 pcs. 7572,7 33 61 10 pcs. 7592,8 33 61 10 pcs. 7622,9 33 61 10 pcs. 7643,0 33 61 10 pcs. 7673,1 36 65 10 pcs. 7713,2 36 65 10 pcs. 774

3,25 36 65 10 pcs. 7753,3 36 65 10 pcs. 7763,4 39 70 10 pcs. 7783,5 39 70 10 pcs. 7803,6 39 70 10 pcs. 7823,7 39 70 10 pcs. 7843,8 43 75 10 pcs. 7863,9 43 75 10 pcs. 7884,0 43 75 10 pcs. 7914,1 43 75 10 pcs. 7944,2 43 75 10 pcs. 796

4,25 43 75 10 pcs. 7974,3 47 80 10 pcs. 7984,4 47 80 10 pcs. 8004,5 47 80 10 pcs. 8024,6 47 80 10 pcs. 804


mm mm mm a4,7 47 80 10 pcs. 8064,8 52 86 10 pcs. 8094,9 52 86 10 pcs. 8125,0 52 86 10 pcs. 8145,1 52 86 10 pcs. 8185,2 52 86 10 pcs. 8205,3 52 86 10 pcs. 8225,4 57 93 10 pcs. 8245,5 57 93 10 pcs. 8255,6 57 93 10 pcs. 8275,7 57 93 10 pcs. 8295,8 57 93 10 pcs. 8315,9 57 93 10 pcs. 8336,0 57 93 10 pcs. 8356,1 63 101 – 8376,2 63 101 – 8396,3 63 101 – 8416,4 63 101 – 8436,5 63 101 – 8446,6 63 101 – 8456,7 63 101 – 847

6,75 69 109 – 8486,8 69 109 – 8496,9 69 109 – 8507,0 69 109 – 8527,1 69 109 – 8547,2 69 109 – 8557,3 69 109 – 8577,4 69 109 – 8587,5 69 109 – 8597,6 75 117 – 8607,7 75 117 – 8617,8 75 117 – 8637,9 75 117 – 8648,0 75 117 – 8678,1 75 117 – 8698,2 75 117 – 8708,3 75 117 – 8728,4 75 117 – 8738,5 75 117 – 8758,6 81 125 – 8778,7 81 125 – 8788,8 81 125 – 8818,9 81 125 – 8829,0 81 125 – 8839,1 81 125 – 8859,2 81 125 – 8879,3 81 125 – 8899,4 81 125 – 8909,5 81 125 – 8919,6 87 133 – 8929,7 87 133 – 8939,8 87 133 – 8959,9 87 133 – 896

10,0 87 133 – 89710,1 87 133 – 898


mm mm mm a10,2 87 133 – 899

10,25 87 133 – 90010,3 87 133 – 90110,4 87 133 – 90310,5 87 133 – 90410,6 87 133 – 90510,7 94 142 – 90610,8 94 142 – 90810,9 94 142 – 90911,0 94 142 – 91011,1 94 142 – 91111,2 94 142 – 91211,4 94 142 – 91411,5 94 142 – 91511,6 94 142 – 91611,7 94 142 – 917

11,75 94 142 – 91811,8 94 142 – 91911,9 101 151 – 92012,0 101 151 – 92112,1 101 151 – 92212,2 101 151 – 92312,3 101 151 – 92512,4 101 151 – 92612,5 101 151 – 92712,6 101 151 – 92812,7 101 151 – 92912,8 101 151 – 93112,9 101 151 – 93213,0 101 151 – 933

13,25 108 160 – 93613,5 108 160 – 937

13,75 108 160 – 94013,8 108 160 – 94114,0 108 160 – 943

14,25 114 169 – 94614,5 114 169 – 948

14,75 114 196 – 94915,0 114 169 – 951

15,25 120 178 – 95415,5 120 178 – 955

15,75 120 178 – 95616,0 120 178 – 95716,5 125 184 – 96517,0 125 184 – 97017,5 130 191 – 97518,0 130 191 – 98018,5 135 198 – 98519,0 135 198 – 99019,5 140 205 – 99520,0 140 205 – 999

10001 HSS

Al<10%Si Al>10%Si Cu St<520N St<750N St<900N St<1100N St<1200N St<1400N <45HRC <55HRC <60HRC <67HRC VA-steel<900N VA-steel>900N Ti alloys GG(G) plastics- - - 25-32 25-32 25-32 - - - - - - - - - - 20-28 20-28

DIN338

. a= Sales are restricted to the packaging units mentioned in the catalogue.

Purchase orders must be in units.

• Twist drills


ß

www.hhw.de 10.7

1

eng/OP

Cutting

Short Twist Drills

0Type Recessed straight shank, right-hand cut, relievedcone grind.QualityHSS ground for steel up to 900 mm2.

Note:Quality drill for highest demands. 10002


mm mm mm13,5 82 156 20214,0 82 156 20514,5 83 157 20715,0 83 157 20915,5 83 157 21116,0 83 157 21316,5 84 158 214


mm mm mm17,0 84 158 21517,5 84 158 21618,0 84 158 21719,0 84 158 21919,5 84 158 22020,0 84 158 221

d1

l

l2

1

10002 HSSDIN338


Performance requires quality.

www.atorn.de

Solid carbide high-performance twist drills by ATORN:

ATORN‘s high-quality drilling tools.


• Twist drills

www.hhw.de10.8

1

eng/OP

Short Twist Drills

10003ß

TypeStraight shank, right-hand cut,relieved cone grind.QualityHSS ground for steel up to 900 mm2.

Note: Budget-priced.

10010TypeStraight shank, right-hand cut, precision-rolled steel.QualityHSS precision-rolled steel for steel up to 900 mm2.

Note: Since there is no discontinuity in the structure of thedrill, it remains elastic and is suitable even forrugged work (e.g. with hand drills).

10003

10010

ß

d1 h8 l2 l1 10003 … 10010 …mm mm mm a0,3 3 19 10 pcs. 101 1010,4 5 20 10 pcs. 102 1020,5 6 22 10 pcs. 103 1030,6 7 24 10 pcs. 104 1040,7 9 28 10 pcs. 105 1050,8 10 30 10 pcs. 106 1060,9 11 32 10 pcs. 107 1071,0 12 34 10 pcs. 108 1081,1 14 36 10 pcs. 109 1091,2 16 38 10 pcs. 110 1101,3 16 38 10 pcs. 111 1111,4 18 40 10 pcs. 112 1121,5 18 40 10 pcs. 113 1131,6 20 43 10 pcs. 114 1141,7 20 43 10 pcs. 115 1151,8 22 46 10 pcs. 116 1161,9 22 46 10 pcs. 117 1172,0 24 49 10 pcs. 118 1182,1 24 49 10 pcs. 119 1192,2 27 53 10 pcs. 120 1202,3 27 53 10 pcs. 121 1212,4 30 57 10 pcs. 122 1222,5 30 57 10 pcs. 123 1232,6 30 57 10 pcs. 124 1242,7 33 61 10 pcs. 125 1252,8 33 61 10 pcs. 126 1262,9 33 61 10 pcs. 127 1273,0 33 61 10 pcs. 128 1283,1 36 65 10 pcs. 129 1293,2 36 65 10 pcs. 130 1303,3 36 65 10 pcs. 131 1313,4 39 70 10 pcs. 132 1323,5 39 70 10 pcs. 133 1333,6 39 70 10 pcs. 134 1343,7 39 70 10 pcs. 135 1353,8 43 75 10 pcs. 136 1363,9 43 75 10 pcs. 137 1374,0 43 75 10 pcs. 138 1384,1 43 75 10 pcs. 139 1394,2 43 75 10 pcs. 140 140

ß

d1 h8 l2 l1 10003 … 10010 …mm mm mm a4,3 47 80 10 pcs. 141 1414,4 47 80 10 pcs. 142 1424,5 47 80 10 pcs. 143 1434,6 47 80 10 pcs. 144 1444,7 47 80 10 pcs. 145 1454,8 52 86 10 pcs. 146 1464,9 52 86 10 pcs. 147 1475,0 52 86 10 pcs. 148 1485,1 52 86 10 pcs. 149 1495,2 52 86 10 pcs. 150 1505,3 52 86 10 pcs. 151 1515,4 57 93 10 pcs. 152 1525,5 57 93 10 pcs. 153 1535,6 57 93 10 pcs. 154 1545,7 57 93 10 pcs. 155 1555,8 57 93 10 pcs. 156 1565,9 57 93 10 pcs. 157 1576,0 57 93 10 pcs. 158 1586,1 63 101 10 pcs. 159 1596,2 63 101 10 pcs. 160 1606,3 63 101 10 pcs. 161 1616,4 63 101 10 pcs. 162 1626,5 63 101 10 pcs. 163 1636,6 63 101 10 pcs. 164 1646,7 63 101 10 pcs. 165 1656,8 69 109 10 pcs. 166 1666,9 69 109 10 pcs. 167 1677,0 69 109 10 pcs. 168 1687,1 69 109 10 pcs. 169 1697,2 69 109 10 pcs. 170 1707,3 69 109 10 pcs. 171 1717,4 69 109 10 pcs. 172 1727,5 69 109 10 pcs. 173 1737,6 75 117 5 pcs. 174 1747,7 75 117 5 pcs. 175 1757,8 75 117 5 pcs. 176 1767,9 75 117 5 pcs. 177 1778,0 75 117 5 pcs. 178 1788,1 75 117 5 pcs. 179 1798,2 75 117 5 pcs. 180 180

ß

d1 h8 l2 l1 10003 … 10010 …mm mm mm a8,3 75 117 5 pcs. 181 1818,4 75 117 5 pcs. 182 1828,5 75 117 5 pcs. 183 1838,6 81 125 5 pcs. 184 1848,7 81 125 5 pcs. 185 1858,8 81 125 5 pcs. 186 1868,9 81 125 5 pcs. 187 1879,0 81 125 5 pcs. 188 1889,1 81 125 5 pcs. 189 1899,2 81 125 5 pcs. 190 1909,3 81 125 5 pcs. 191 1919,4 81 125 5 pcs. 192 1929,5 81 125 5 pcs. 193 1939,6 87 133 5 pcs. 194 1949,7 87 133 5 pcs. 195 1959,8 87 133 5 pcs. 196 1969,9 87 133 5 pcs. 197 197

10,0 87 133 5 pcs. 198 19810,1 87 133 5 pcs. 19910,2 87 133 5 pcs. 200 20010,5 87 133 5 pcs. 203 20310,8 94 142 – 206 20611,0 94 142 – 208 20811,2 94 142 – 210 21011,5 94 142 – 213 21311,8 94 142 – 216 21612,0 101 151 – 218 21812,2 101 151 – 220 22012,5 101 151 – 223 22312,8 101 151 – 226 22613,0 101 151 – 228 22813,5 108 160 – 233 23313,8 108 160 – 238 23814,0 108 160 – 243 24314,5 114 169 – 248 24815,0 114 169 – 253 25315,5 120 178 – 258 25816,0 120 178 – 263 263

d1

l

l2

1

10003 - 10010

10003Al<10%Si Al>10%Si Cu St<520N St<750N St<900N St<1100N St<1200N St<1400N <45HRC <55HRC <60HRC <67HRC VA-steel<900N VA-steel>900N Ti alloys GG(G) plastics

50-60 40-50 60-80 25-32 25-32 25-32 - - - - - - - - - - 20-28 20-2810010


HSSDIN338




ß

www.hhw.de 10.9

1

eng/OP

Cutting

010020TypeStraight shank, right-hand cut, relieved cone grind.Web-thinned chisel edge. High true-runningaccuracy. Long service life.QualityHSS/TiN for steel with a strength of up to 1200mm2, cast iron, graphite, brass, etc.

Note: Drills for production.

10035Multi-purpose twist drills MBS 1200TypeStraight shank, right-hand cut, relieved cone grind.Special web-thinning. 4 surfaces pre-ground.QualityHSS-E ground.

Note: Multi-purpose use, quiet drilling, low torque, highdimensional accuracy, perfect chip removal thanksto the round flute profile.

10020

10035

HSS/TiN MBS 1200d1 h8 l2 l1 10020 … 10035 …mm mm mm a1,0 12 34 10 pcs. 605 0101,1 14 36 10 pcs. 606 0111,2 16 38 10 pcs. 608 0121,3 16 38 10 pcs. 610 0131,4 18 40 10 pcs. 612 0141,5 18 40 10 pcs. 614 0151,6 20 43 10 pcs. 615 0161,7 20 43 10 pcs. 617 0171,8 22 46 10 pcs. 618 0181,9 22 46 10 pcs. 619 0192,0 24 49 10 pcs. 620 0202,1 24 49 10 pcs. 622 0212,2 27 53 10 pcs. 624 0222,3 27 53 10 pcs. 626 0232,4 30 57 10 pcs. 627 0242,5 30 57 10 pcs. 629 0252,6 30 57 10 pcs. 630 0262,7 33 61 10 pcs. 631 0272,8 33 61 10 pcs. 633 0282,9 33 61 10 pcs. 640 0293,0 33 61 10 pcs. 642 0303,1 36 65 10 pcs. 644 0313,2 36 65 10 pcs. 645 0323,3 36 65 10 pcs. 646 0333,4 39 70 10 pcs. 647 0343,5 39 70 10 pcs. 648 0353,6 39 70 10 pcs. 650 0363,7 39 70 10 pcs. 651 0373,8 43 75 10 pcs. 652 0383,9 43 75 10 pcs. 653 0394,0 43 75 10 pcs. 655 0404,1 43 75 10 pcs. 656 0414,2 43 75 10 pcs. 658 0424,3 47 80 10 pcs. 659 0434,4 47 80 10 pcs. 660 0444,5 47 80 10 pcs. 661 0454,6 47 80 10 pcs. 662 0464,7 47 80 10 pcs. 663 0474,8 52 86 10 pcs. 664 0484,9 52 86 10 pcs. 665 0495,0 52 86 10 pcs. 666 0505,1 52 86 10 pcs. 667 0515,2 52 86 10 pcs. 668 0525,3 52 86 10 pcs. 669 0535,4 57 93 10 pcs. 670 0545,5 57 93 10 pcs. 671 0555,6 57 93 10 pcs. 672 0565,7 57 93 10 pcs. 673 0575,8 57 93 10 pcs. 674 0585,9 57 93 10 pcs. 675 0596,0 57 93 10 pcs. 676 0606,1 63 101 – 677 061

d1

l

l2

1

Short Twist Drills 10020 - 10035

HSS-E

HSS/TiN MBS 1200d1 h8 l2 l1 10020 … 10035 …mm mm mm a6,2 63 101 – 678 0626,3 63 101 – 679 0636,4 63 101 – 680 0646,5 63 101 – 681 0656,6 63 101 – 682 0666,7 63 101 – 683 0676,8 69 109 – 684 0686,9 69 109 – 685 0697,0 69 109 – 686 0707,1 69 109 – 687 0717,2 69 109 – 688 0727,3 69 109 – 689 0737,4 69 109 – 690 0747,5 69 109 – 691 0757,6 75 117 – 692 0767,7 75 117 – 693 0777,8 75 117 – 694 0787,9 75 117 – 695 0798,0 75 117 – 696 0808,1 75 117 – 697 0818,2 75 117 – 698 0828,3 75 117 – 699 0838,4 75 117 – 700 0848,5 75 117 – 701 0858,6 81 125 – 7028,7 81 125 – 7038,8 81 125 – 704 0888,9 81 125 – 7059,0 81 125 – 706 0909,1 81 125 – 7079,2 81 125 – 7089,3 81 125 – 709 0939,4 81 125 – 7109,5 81 125 – 711 0959,6 87 133 – 7129,7 87 133 – 7139,8 87 133 – 714 0989,9 87 133 – 715

10,0 87 133 – 716 10010,2 87 133 – 718 10210,5 87 133 – 721 10511,0 94 142 – 726 11011,5 94 142 – 731 11512,0 101 151 – 736 12012,5 101 151 – 741 12513,0 101 151 – 746 13014,0 108 160 – 75514,5 114 169 – 76015,0 114 169 – 76515,5 120 178 – 77016,0 120 178 – 775

DIN338




70-80 60-70 80-100 25-32 25-32 25-32 18-20 - - - - - - - - - 20-36 20-3210035

Al<10%Si Al>10%Si Cu St<520N St<750N St<900N St<1100N St<1200N St<1400N <45HRC <55HRC <60HRC <67HRC VA-steel<900N VA-steel>900N Ti alloys GG(G) plastics40-55 30-35 25-35 30-35 20-32 13-16 10-15 10-15 - - - - - 12-14 10-12 - 30-36 -


• Twist drills

www.hhw.de10.10

1

eng/OP

Short Twist Drills

ßTypeStraight shank, right-hand cut, relieved cone grind.Starting at 2,4 mm, with web-thinned chisel edge. High true-running accuracy, precisely ground centrepoint.QualityHSS-E ground for high-alloyed steel with astrength of up to 1200 N/mm2.

Note: Quality drill which satisfies the highest requirements.Drill for production.

10040

HSS-Ed1 h8 l2 l1 10040 …

mm mm mm a0,3 3 19 10 pcs. 6090,4 5 20 10 pcs. 6180,5 6 22 10 pcs. 6260,6 7 24 10 pcs. 6350,7 9 28 10 pcs. 6440,8 10 30 10 pcs. 6540,9 11 32 10 pcs. 6631,0 12 34 10 pcs. 6721,1 14 36 10 pcs. 6791,2 16 38 10 pcs. 6881,3 16 38 10 pcs. 6971,4 18 40 10 pcs. 6991,5 18 40 10 pcs. 7041,6 20 43 10 pcs. 7121,7 20 43 10 pcs. 7171,8 22 46 10 pcs. 7241,9 22 46 10 pcs. 7302,0 24 49 10 pcs. 7372,1 24 49 10 pcs. 7412,2 27 53 10 pcs. 7432,3 27 53 10 pcs. 7452,4 30 57 10 pcs. 7502,5 30 57 10 pcs. 7532,6 30 57 10 pcs. 7572,7 33 61 10 pcs. 7592,8 33 61 10 pcs. 7622,9 33 61 10 pcs. 7643,0 33 61 10 pcs. 7673,1 36 65 10 pcs. 7713,2 36 65 10 pcs. 7743,3 36 65 10 pcs. 7763,4 39 70 10 pcs. 7783,5 39 70 10 pcs. 7803,6 39 70 10 pcs. 7823,7 39 70 10 pcs. 7843,8 43 75 10 pcs. 7863,9 43 75 10 pcs. 7884,0 43 75 10 pcs. 7914,1 43 75 10 pcs. 7944,2 43 75 10 pcs. 796

HSS-Ed1 h8 l2 l1 10040 …

mm mm mm a4,3 47 80 10 pcs. 7984,4 47 80 10 pcs. 8004,5 47 80 10 pcs. 8024,6 47 80 10 pcs. 8044,7 47 80 10 pcs. 8064,8 52 86 10 pcs. 8094,9 52 86 10 pcs. 8125,0 52 86 10 pcs. 8145,1 52 86 10 pcs. 8185,2 52 86 10 pcs. 8205,3 52 86 10 pcs. 8225,4 57 93 10 pcs. 8245,5 57 93 10 pcs. 8255,6 57 93 10 pcs. 8275,7 57 93 10 pcs. 8295,8 57 93 10 pcs. 8315,9 57 93 10 pcs. 8336,0 57 93 10 pcs. 8356,1 63 101 10 pcs. 8376,2 63 101 10 pcs. 8396,3 63 101 10 pcs. 8416,4 63 101 10 pcs. 8436,5 63 101 10 pcs. 8446,6 63 101 10 pcs. 8456,7 63 101 10 pcs. 8476,8 69 109 10 pcs. 8496,9 69 109 10 pcs. 8507,0 69 109 10 pcs. 8527,1 69 109 10 pcs. 8547,2 69 109 10 pcs. 8557,3 69 109 10 pcs. 8577,4 69 109 10 pcs. 8587,5 69 109 10 pcs. 8597,6 75 117 5 pcs. 8607,7 75 117 5 pcs. 8617,8 75 117 5 pcs. 8637,9 75 117 5 pcs. 8648,0 75 117 5 pcs. 8678,1 75 117 5 pcs. 8698,2 75 117 5 pcs. 870

HSS-Ed1 h8 l2 l1 10040 …

mm mm mm a8,3 75 117 5 pcs. 8728,4 75 117 5 pcs. 8738,5 75 117 5 pcs. 8758,6 81 125 5 pcs. 8778,7 81 125 5 pcs. 8788,8 81 125 5 pcs. 8818,9 81 125 5 pcs. 8829,0 81 125 5 pcs. 8839,1 81 125 5 pcs. 8859,2 81 125 5 pcs. 8879,3 81 125 5 pcs. 8899,4 81 125 5 pcs. 8909,5 81 125 5 pcs. 8919,6 87 133 5 pcs. 8929,7 87 133 5 pcs. 8939,8 87 133 5 pcs. 8959,9 87 133 5 pcs. 896

10,0 87 133 5 pcs. 89710,1 87 133 5 pcs. 89810,2 87 133 5 pcs. 89910,5 87 133 5 pcs. 90410,8 94 142 – 90811,0 94 142 – 91011,2 94 142 – 91211,5 94 142 – 91511,8 94 142 – 91912,0 101 151 – 92112,2 101 151 – 92312,5 101 151 – 92712,8 101 151 – 93113,0 101 151 – 93313,5 108 160 – 93713,8 108 160 – 94114,0 108 160 – 94314,5 114 169 – 94815,0 114 169 – 95115,5 120 178 – 95516,0 120 178 – 957

d1

l

l2

1

10040

Al<10%Si Al>10%Si Cu St<520N St<750N St<900N St<1100N St<1200N St<1400N <45HRC <55HRC <60HRC <67HRC VA-steel<900N VA-steel>900N Ti alloys GG(G) plastics- - - 30-40 25-28 15-28 15-22 14-18 10-12 - - - - 12-14 - 6-10 - 15-18

HSS-EDIN338



Performance requires quality.www.atorn.de

Solid carbide milling cutters by ATORN:

ATORN‘s high-quality milling tools.


ß

www.hhw.de 10.11

1

eng/OP

Cutting

0TypeStraight shank, right-hand cut, relieved cone grind.Starting at 1 mm, with web-thinned chisel edge.High true-running accuracy, precisely ground centrepoint.

Note: Quality drill to satisfy the highest requirements. Drill for production.

10042 QualityHSS-E for difficult to machine materials such astitanium and exotic materials such as Nimonic,Hastelloy, and Inconel.

10044 QualityHSS-E/TiAlN-coated, for high-alloyed steel with astrength of up to 1200 N/mm2. Extreme service lives are possible.

10046 QualityHSS-E for corrosion, acid, and heat-resistantsteel such as V2A and V4A.

10042

10044

10046

Short Twist Drills 10042 - 10046

HSS-E

HSS-ETiAIN

HSS-E

DIN338



VA

continuation .

Type Ti Type N Type VAd1 h8 l2 l1 10042 … 10044 … 10046 …

mm mm mm a0,5 6 22 10 pcs. 1050,6 7 24 10 pcs. 1061,0 12 34 10 pcs. 110 110 1101,1 14 36 10 pcs. 111 1111,2 16 38 10 pcs. 112 1121,3 16 38 10 pcs. 113 1131,4 18 40 10 pcs. 114 1141,5 18 40 10 pcs. 115 115 1151,6 20 43 10 pcs. 116 116 1161,7 20 43 10 pcs. 117 1171,8 22 46 10 pcs. 118 1181,9 22 46 10 pcs. 119 1192,0 24 49 10 pcs. 120 120 1202,1 24 49 10 pcs. 121 1212,2 27 53 10 pcs. 122 122 1222,3 27 53 10 pcs. 123 1232,4 30 57 10 pcs. 124 124 1242,5 30 57 10 pcs. 125 125 1252,6 30 57 10 pcs. 126 1262,7 33 61 10 pcs. 127 1272,8 33 61 10 pcs. 128 128 1282,9 33 61 10 pcs. 129 129 1293,0 33 61 10 pcs. 130 130 1303,1 36 65 10 pcs. 131 131 1313,2 36 65 10 pcs. 132 132 1323,3 36 65 10 pcs. 133 133 1333,4 39 70 10 pcs. 134 134 1343,5 39 70 10 pcs. 135 135 1353,6 39 70 10 pcs. 136 136 1363,7 39 70 10 pcs. 137 1373,8 43 75 10 pcs. 138 1383,9 43 75 10 pcs. 139 139 1394,0 43 75 10 pcs. 140 140 1404,1 43 75 10 pcs. 141 141 1414,2 43 75 10 pcs. 142 142 1424,3 47 80 10 pcs. 143 1434,4 47 80 10 pcs. 144 1444,5 47 80 10 pcs. 145 145 1454,6 47 80 10 pcs. 146 1464,7 47 80 10 pcs. 147 1474,8 52 86 10 pcs. 148 148 1484,9 52 86 10 pcs. 149 1495,0 52 86 10 pcs. 150 150 1505,1 52 86 10 pcs. 151 151 1515,2 52 86 10 pcs. 152 152 1525,3 52 86 10 pcs. 153 1535,4 57 93 10 pcs. 154 1545,5 57 93 10 pcs. 155 155 1555,6 57 93 10 pcs. 156 156

Type Ti Type N Type VAd1 h8 l2 l1 10042 … 10044 … 10046 …

mm mm mm a5,7 57 93 10 pcs. 157 1575,8 57 93 10 pcs. 158 158 1585,9 57 93 10 pcs. 159 1596,0 57 93 10 pcs. 160 160 1606,1 63 101 – 161 1616,2 63 101 – 162 1626,3 63 101 – 163 1636,4 63 101 – 164 1646,5 63 101 – 165 165 1656,6 63 101 – 166 1666,7 63 101 – 167 1676,8 69 109 – 168 168 1686,9 69 109 – 169 1697,0 69 109 – 170 170 1707,1 69 109 – 171 1717,2 69 109 – 172 1727,3 69 109 – 173 1737,4 69 109 – 174 1747,5 69 109 – 175 175 1757,6 75 117 – 176 1767,7 75 117 – 177 1777,8 75 117 – 178 178 1787,9 75 117 – 179 1798,0 75 117 – 180 180 1808,1 75 117 – 181 1818,2 75 117 – 182 182 1828,3 75 117 – 183 1838,4 75 117 – 184 184 1848,5 75 117 – 185 185 1858,6 81 125 – 186 1868,7 81 125 – 187 1878,8 81 125 – 188 188 1888,9 81 125 – 189 1899,0 81 125 – 190 190 1909,1 81 125 – 191 1919,2 81 125 – 192 1929,3 81 125 – 193 1939,4 81 125 – 194 1949,5 81 125 – 195 195 1959,6 87 133 – 196 1969,7 87 133 – 197 1979,8 87 133 – 198 198 1989,9 87 133 – 199 199

10,0 87 133 – 200 200 20010,2 87 133 – 202 202 20210,5 87 133 – 205 205 20511,0 94 142 – 210 210 21011,5 94 142 – 215 215 21511,8 94 142 – 218 218


• Twist drills

www.hhw.de10.12

1

eng/OP


- - - 35-40 30-35 25-30 15-20 15-20 12-15 - - - - 10-14 10-14 8-9 - -10044

Al<10%Si Al>10%Si Cu St<520N St<750N St<900N St<1100N St<1200N St<1400N <45HRC <55HRC <60HRC <67HRC VA-steel<900N VA-steel>900N Ti alloys GG(G) plastics- - - 35-40 30-35 25-30 20-25 15-20 12-15 - - - - - - - 23-35 -


85-90 50-60 20-45 - - - - - - - - - - 12-14 10-12 - - -

Typ Ti Typ N Typ VAd1 h8 l2 l1 10042 … 10044 … 10046 …

mm mm mm a12,0 101 151 – 220 220 22012,2 101 151 – 22212,5 101 151 – 22513,0 101 151 – 230 23013,5 108 160 – 235

Typ Ti Typ N Typ VAd1 h8 l2 l1 10042 … 10044 … 10046 …

mm mm mm a14,0 108 160 – 24014,5 114 169 – 24515,0 114 169 – 25015,5 120 178 – 25516,0 120 178 – 260

Co8 Twist Drill10047

0TypeStraight shank, right-hand cut, relieved cone grind,web-thinned chisel edge, high true-running accura-cy, precisely ground ground centre point. Drillingwithout centring.

QualityHSS-Co8 ground for high-strength alloys basedon CrNi. VA-steel, wear-resistant sheet metaland steel with a strength of up to 1400 N/mm2.

Note: Quality drill to satisfy the utmost requirements. Drills for production.

10047

Al<10%Si Al>10%Si Cu St<520N St<750N St<900N St<1100N St<1200N St<1400N <45HRC <55HRC <60HRC <67HRC VA-steel<900N VA-steel>900N Ti alloys GG(G) plastics- - - 35-40 32-35 25-32 20-25 10-20 10-12 - - - - - - 5-6 - -

HSS-Ed1 h8 l2 l1 10047 …

mm mm mm a1,0 12 34 10 pcs. 1101,1 14 36 10 pcs. 1111,2 16 38 10 pcs. 1121,3 16 38 10 pcs. 1131,4 18 40 10 pcs. 1141,5 18 40 10 pcs. 1151,6 20 43 10 pcs. 1161,7 20 43 10 pcs. 1171,8 22 46 10 pcs. 1181,9 22 46 10 pcs. 1192,0 24 49 10 pcs. 1202,1 24 49 10 pcs. 1212,2 27 53 10 pcs. 1222,3 27 53 10 pcs. 1232,4 30 57 10 pcs. 1242,5 30 57 10 pcs. 1252,6 30 57 10 pcs. 1262,7 33 61 10 pcs. 1272,9 33 61 10 pcs. 1293,0 33 61 10 pcs. 1303,1 36 65 10 pcs. 1313,2 36 65 10 pcs. 1323,3 36 65 10 pcs. 1333,4 39 70 10 pcs. 1343,5 39 70 10 pcs. 1353,6 39 70 10 pcs. 1363,7 39 70 10 pcs. 1373,8 43 75 10 pcs. 1383,9 43 75 10 pcs. 1394,0 43 75 10 pcs. 1404,1 43 75 10 pcs. 1414,2 43 76 10 pcs. 1424,3 47 80 10 pcs. 143

HSS-Ed1 h8 l2 l1 10047 …

mm mm mm a4,4 47 80 10 pcs. 1444,5 47 80 10 pcs. 1454,6 47 80 10 pcs. 1464,7 47 80 10 pcs. 1474,8 52 86 10 pcs. 1484,9 52 86 10 pcs. 1495,0 52 86 10 pcs. 1505,1 52 86 10 pcs. 1515,2 52 86 10 pcs. 1525,3 52 86 10 pcs. 1535,4 57 93 10 pcs. 1545,5 57 93 10 pcs. 1555,6 57 93 10 pcs. 1565,7 57 93 10 pcs. 1575,8 57 93 10 pcs. 1585,9 57 93 10 pcs. 1596,0 57 93 10 pcs. 1606,1 63 101 – 1616,2 63 101 – 1626,3 63 101 – 1636,4 63 101 – 1646,5 63 101 – 1656,6 63 101 – 1666,7 63 101 – 1676,8 69 109 – 1686,9 69 109 – 1697,0 69 109 – 1707,1 69 109 – 1717,2 69 109 – 1727,3 69 109 – 1737,4 69 109 – 1747,5 69 109 – 1757,6 75 117 – 176

HSS-Ed1 h8 l2 l1 10047 …

mm mm mm a7,7 75 117 – 1777,8 75 117 – 1787,9 75 117 – 1798,0 75 117 – 1808,1 75 117 – 1818,2 75 117 – 1828,3 75 117 – 1838,4 75 117 – 1848,5 75 117 – 1858,6 81 125 – 1868,7 81 125 – 1878,8 81 125 – 1888,9 81 125 – 1899,0 81 125 – 1909,1 81 125 – 1919,2 81 125 – 1929,3 81 125 – 1939,4 81 125 – 1949,5 81 125 – 1959,6 87 133 – 1969,7 87 133 – 1979,8 87 133 – 1989,9 87 133 – 199

10,0 87 133 – 20010,1 87 133 – 20110,5 87 133 – 20511,0 94 142 – 21011,5 94 142 – 21511,8 94 142 – 21812,0 101 151 – 22012,5 101 151 – 22513,0 101 151 – 230

DIN338

Short Twist Drills 10042 - 10046 DIN338




ß

www.hhw.de 10.13

1

eng/OP

Cutting

Short Twist Drills

0TypeStraight shank, right-hand cut, relieved cone grind,web-thinned chisel edge, high true-running accura-cy, precisely ground ground centre point. Above 2mm nitrided lands. Wide cutting flutes and roundedheels for perfect chip transport.

Note: Quality drill for utmost demands. Drills for production.

10050 QualityHSS-E for steel with a strength of up to 1200N/mm2.

10053 QualityHSS-E/TiN-coated for even higher machiningperformance.

10050

HSS-E HSS-E/TiNd1 h8 l2 l1 10050 … 10053 …

mm mm mm a1,0 12 34 10 pcs. 101 1101,1 14 36 10 pcs. 1071,2 16 38 10 pcs. 1121,3 16 38 10 pcs. 1151,4 18 40 10 pcs. 1181,5 18 40 10 pcs. 122 1151,6 20 43 10 pcs. 126 1161,7 20 43 10 pcs. 129 1171,8 22 46 10 pcs. 1311,9 22 46 10 pcs. 1332,0 24 49 10 pcs. 140 1202,1 24 49 10 pcs. 144 1212,2 27 53 10 pcs. 1472,3 27 53 10 pcs. 1502,4 30 57 10 pcs. 154 1242,5 30 57 10 pcs. 159 1252,6 30 57 10 pcs. 1632,7 33 61 10 pcs. 1662,8 33 61 10 pcs. 171 1282,9 33 61 10 pcs. 175 1293,0 33 61 10 pcs. 177 1303,1 36 65 10 pcs. 179 1313,2 36 65 10 pcs. 182 1323,3 36 65 10 pcs. 185 1333,4 39 70 10 pcs. 186 1343,5 39 70 10 pcs. 188 1353,6 39 70 10 pcs. 190 1363,7 39 70 10 pcs. 1933,8 43 75 10 pcs. 195 1383,9 43 75 10 pcs. 197 1394,0 43 75 10 pcs. 201 1404,1 43 75 10 pcs. 206 1414,2 43 75 10 pcs. 208 1424,3 47 80 10 pcs. 2114,4 47 80 10 pcs. 2144,5 47 80 10 pcs. 215 1454,8 52 86 10 pcs. 224 1485,0 52 86 10 pcs. 229 150

HSS-E HSS-E/TiNd1 h8 l2 l1 10050 … 10053 …

mm mm mm a5,1 52 86 10 pcs. 231 1515,2 52 86 10 pcs. 235 1525,3 52 86 10 pcs. 2385,4 57 93 10 pcs. 2405,5 57 93 10 pcs. 242 1555,7 57 93 10 pcs. 2465,8 57 93 10 pcs. 249 1586,0 57 93 10 pcs. 252 1606,1 63 101 – 2556,2 63 101 – 257 1626,3 63 101 – 2596,5 63 101 – 262 1656,6 63 101 – 2646,7 63 101 – 2676,8 69 109 – 269 1686,9 69 109 – 2717,0 69 109 – 272 1707,1 69 109 – 2747,4 69 109 – 2807,5 69 109 – 283 1757,8 75 117 – 2897,9 75 117 – 2908,0 75 117 – 292 1808,2 75 117 – 295 1828,5 75 117 – 300 1858,8 81 125 – 3069,0 81 125 – 309 1909,2 81 125 – 3139,5 81 125 – 317 1959,7 87 133 – 321

10,0 87 133 – 325 20010,2 87 133 – 328 20210,5 87 133 – 333 20511,0 94 142 – 339 21011,5 94 142 – 345 21512,0 101 151 – 351 22012,5 101 151 – 35313,0 101 151 – 356

10053

d1

l

l2

1

10050 - 10053


- - - 30-40 25-28 15-28 15-22 14-18 - - - - - - - - 25-30 -10053

Al<10%Si Al>10%Si Cu St<520N St<750N St<900N St<1100N St<1200N St<1400N <45HRC <55HRC <60HRC <67HRC VA-steel<900N VA-steel>900N Ti alloys GG(G) plastics- - - 40-45 35-40 20-28 18-22 17-22 - - - - - - - - 32-38 -

FS

HSS-E

HSS-ETiN

DIN338




• Twist drills

www.hhw.de10.14

1

eng/OP

Twist Drill Sets in Cassette

TypeA combination of HSS multi-uni-versal twist drills DIN 338 type N.When the lid is opened, the drillsare automatically tilted up to thevertical position and can be takenout from the drill holders, whichare individually marked with thedrill size. The drills will not movearound in the closed cassette.

Note:The boxes with the final digits 115(1-10,5 mm) also contain twistdrills 3,3 / 4,2 / 6,8 / 10,2 mm Øfor threaded holes (ISO).

10170

0Type NHSS, ground (cat.-no. 10001).

10173 ß

Type NHSS, ground (cat.-no. 10003).

10174

0Type NHSS/TiN, ground (cat.-no. 10020).

10034

0Type UNIHSS-E.(cat.-no. 10035).

10177ß

Type NHSS-E, ground (cat.-no. 10040).

10178Type NHSS, precisely rolled steel (cat.-no. 10010).

10170 118

10034 114

HSS HSS HSS/TiN HSS-E HSS-E HSS rolled steelSet size Number of increments 10170 … 10173 … 10174 … 10034 … 10177 … 10178 …

mm drills mm mm1,0 - 6,0 51 0,1 106 106 106 106

2,0 - 10,0 81 0,1 108 108 108 1086,0 - 10,0 41 0,1 109 109 109 1091,0 - 10,0 19 0,5 114 114 114 114 114 1141,0 - 10,5 24 0,5 115 115 115 115 115 1151,0 - 13,0 25 0,5 118 118 118 118 118 118

10034 - 10178

Twist Drill Sets

TypeSheet steel case with 180 twistdrills. Contents:each 10 pcs. 0,5-8 mm,each 5 pcs. 8,5-10 mm,in steps of 0,5 mm.

10180

0HSS, ground(cat.-no. 10001).

10181ß

HSS, ground(cat.-no. 10003).

10182HSS, precision-rolled steel.(cat.-no. 10010).

10183TypeEmpty case.For max. 600 twist drills(0,5-10 mm Ø, 0,5 mm/incre-ments).Dimensions: 325 x 225 x 50 mm.

HSS HSS HSS rolled steel empty10180 … 10181 … 10182 … 10183 …

101 101 201 101

10180 - 10183

10180 - 10182

Twist Drill Sets DIN 338 Type N

TypeSets packed in oil paper.ApplicationFor re-filling and completing twistdrill assortment cases.

Note:The boxes with the final digits 115(1-10,5 mm) also contain twistdrills 3,3 / 4,2 / 6,8 / 10,2 mm Øfor threaded holes (ISO).

10185

0HSS, ground (cat.-no. 10001).

10186 ß

HSS, ground (cat.-no. 10003).

10187 ß

HSS-E, ground (cat.-no. 10040).

10188HSS, precision-rolled steel. (cat.-no. 10010).

10185 - 10188

10185 - 10188

HSS HSS HSS-E HSS rolled steelSet size No. of Increments 10185 … 10186 … 10187 … 10188 …

mm drills mm mm1,0 - 6,0 51 0,1 106 106 106 106

2,0 - 10,0 81 0,1 108 108 108 1086,0 - 10,0 41 0,1 109 109 109 1091,0 - 10,0 19 0,5 114 114 114 1141,0 - 10,5 24 0,5 115 115 115 1151,0 - 13,0 25 0,5 118 118 118 118

HSS

HSS HSS-E

DIN338

DIN338

DIN338

HSS HSS-E


ß

www.hhw.de 10.15

1

eng/OP

Cutting

Twist Drill Cases (Empty)

TypeWithout drills.When the lid is opened, the drills are automaticallytilted up to vertical position.ApplicationFor clearly arranged storage of short twist drills withstraight shank DIN 338, in sets (cat.-no. 10185 -10188) and all other short twist drills with straightshank with the respective diameters and lengths.

Note:Cat.-no.10190115 - 116 with additional slots for thread core drills (ISO and BSW):cat.-no. 10190 115 =3,3 / 4,2 / 6,8 and 10,2 mm,cat.-no. 10190 116 =1,9 / 2,1 / 2,6 / 2,9 / 3,2 / 3,3 / 3,8 / 4,2 / 5,1 / 6,8 /7,9 / 10,2 mm.

10190

for twist drills number of Increments 10190 …sets Ø mm drills mm

1,0 - 6,0 51 0,1 1062,0 - 10,0 81 0,1 1086,0 - 10,0 41 0,1 1091,0 - 10,0 19 0,5 114

for twist drills number of Increments 10190 …sets Ø mm drills mm

1,0 - 10,5 24 0,5 1151,0 - 10,5 32 0,5 1161,0 - 13,0 25 0,5 118

10190

Plastic Stands for Twist Drills (Empty)

TypeWithout drills.ApplicationFor clearly organised storage of twist drills withstraight shank in different sets.

10195

for Set size Increments 10195 …mm mm mm1,0 - 5,0 0,1 101

5,1 - 10,0 0,1 1031,0 - 5,9 0,1 107

1,0 - 10,0 0,5 1141,0 - 13,0 0,5 118

Short Twist Drills10210 - 10214

T10210TypeStraight shank, right-hand cut,relieved cone grind.QualityHSS ground.

Note: Special drill with wide, spacious flutes for hard andbrittle materials (brass, bronze).

10211Aluminium twist drillTypeStraight shank, right-hand cut,relieved cone grind.QualityHSS ground.

Note:Special drill with polished flutes for perfect chiptransport in soft materials.Drill for production.

10214VA-steel twist drillTypeStraight shank, right-hand cut, relieved cone grind.Starting at 1 mm, with web-thinned chisel edge.High true-running accuracy, precisely ground centrepoint.Drilling without centring.QualityHSS-E ground.

Note: For corrosion, acid, and heat-resistant steel such as V2A and V4A.Drill for production.

10210

10211

d1

l2l1

d1

l2l1

10214

d1

l2l1

HSS HSS HSS-Ed1 h8 l2 l1 10210 … 10211 … 10214 …

mm mm mm a0,5 6 22 10 pcs. 101 1010,6 7 24 10 pcs. 102 1020,7 9 28 10 pcs. 103 1030,8 10 30 10 pcs. 104 1040,9 11 32 10 pcs. 105 1051,0 12 34 10 pcs. 106 1061,1 14 36 10 pcs. 107 107 6021,2 16 38 10 pcs. 108 108 6031,3 16 38 10 pcs. 109 109 6041,4 18 40 10 pcs. 110 110 6051,5 18 40 10 pcs. 111 111 606

HSS HSS HSS-Ed1 h8 l2 l1 10210 … 10211 … 10214 …

mm mm mm a1,6 20 43 10 pcs. 112 112 6071,7 20 43 10 pcs. 113 113 6081,8 22 46 10 pcs. 114 114 6091,9 22 46 10 pcs. 115 115 6102,0 24 49 10 pcs. 116 116 6112,1 24 49 10 pcs. 117 117 6122,2 27 53 10 pcs. 118 118 6132,3 27 53 10 pcs. 119 6142,4 30 57 10 pcs. 120 120 6152,5 30 57 10 pcs. 121 121 6162,6 30 57 10 pcs. 122 122 617

HSS

DIN338

10195



HSS

VAHSS-E

continuation .


• Twist drills • Short-chip drill

www.hhw.de10.16

1

eng/OP

10210Al<10%Si Al>10%Si Cu St<520N St<750N St<900N St<1100N St<1200N St<1400N <45HRC <55HRC <60HRC <67HRC VA-steel<900NVA-steel>900NTi alloys GG(G) plastics

- - 25-32 40-63 70-80 - - - - - - - - - - - -


50-55 60-70 32-36 - - - - - - - - - - 10-14 8-10 - - -


50-60 40-50 25-32 - - - - - - - - - - - - - - -

HSS HSS HSS-Ed1 h8 l2 l1 10210 … 10211 … 10214 …

mm mm mm a2,7 33 61 10 pcs. 123 123 6182,8 33 61 10 pcs. 124 124 6192,9 33 61 10 pcs. 125 125 6203,0 33 61 10 pcs. 126 126 6213,1 36 65 10 pcs. 127 127 6223,2 36 65 10 pcs. 128 128 6233,3 36 65 10 pcs. 129 129 6243,4 39 70 10 pcs. 130 130 6253,5 39 70 10 pcs. 131 131 6263,6 39 70 10 pcs. 132 132 6273,7 39 70 10 pcs. 133 133 6283,8 43 75 10 pcs. 134 134 6293,9 43 75 10 pcs. 135 135 6304,0 43 75 10 pcs. 136 136 6314,1 43 75 10 pcs. 137 137 6324,2 43 75 10 pcs. 138 138 6334,3 47 80 10 pcs. 139 139 6344,4 47 80 10 pcs. 140 140 6354,5 47 80 10 pcs. 141 141 6364,6 47 80 10 pcs. 142 142 6374,7 47 80 10 pcs. 143 143 6384,8 52 86 10 pcs. 144 144 6394,9 52 86 10 pcs. 145 145 6405,0 52 86 10 pcs. 146 146 6415,1 52 86 10 pcs. 147 147 6425,2 52 86 10 pcs. 148 148 6435,3 52 86 10 pcs. 149 149 6445,4 57 93 10 pcs. 150 1505,5 57 93 10 pcs. 151 151 6465,6 57 93 10 pcs. 152 152 6475,7 57 93 10 pcs. 153 1535,8 57 93 10 pcs. 154 154 6505,9 57 93 10 pcs. 155 155 6516,0 57 93 10 pcs. 156 156 6526,1 63 101 10 pcs. 157 157 6536,2 63 101 10 pcs. 158 158 6546,3 63 101 10 pcs. 159 159 6556,4 63 101 10 pcs. 160 160 6566,5 63 101 10 pcs. 161 161 6576,6 63 101 10 pcs. 162 162 6586,7 63 101 10 pcs. 163 163 6596,8 69 109 10 pcs. 164 164 6616,9 69 109 10 pcs. 165 165 662

HSS HSS HSS-Ed1 h8 l2 l1 10210 … 10211 … 10214 …

mm m mm a7,0 69 109 10 pcs. 166 166 6637,1 69 109 10 pcs. 186 186 6647,2 69 109 10 pcs. 167 167 6657,3 69 109 10 pcs. 187 187 6667,4 69 109 10 pcs. 188 6677,5 69 109 10 pcs. 168 168 6687,6 75 117 5 pcs. 189 1897,7 75 117 5 pcs. 6707,8 75 117 5 pcs. 169 169 6717,9 75 117 5 pcs. 191 191 6728,0 75 117 5 pcs. 170 170 6738,1 75 117 5 pcs. 192 192 6748,2 75 117 5 pcs. 171 171 6758,3 75 117 5 pcs. 1938,4 75 117 5 pcs. 193 1948,5 75 117 5 pcs. 172 172 6788,6 81 125 5 pcs. 194 195 6798,7 81 125 5 pcs. 196 6808,8 81 125 5 pcs. 173 173 6819,0 81 125 5 pcs. 174 174 6839,1 81 125 5 pcs. 198 6849,2 81 125 5 pcs. 175 175 6859,3 81 125 5 pcs. 197 199 6869,4 81 125 5 pcs. 6879,5 81 125 5 pcs. 176 176 6889,7 87 133 5 pcs. 199 6909,8 87 133 5 pcs. 177 177 6919,9 87 133 5 pcs. 692

10,0 87 133 5 pcs. 178 178 69310,1 87 133 5 pcs. 200 204 69410,2 87 133 5 pcs. 205 69510,3 87 133 5 pcs. 69610,4 87 133 5 pcs. 69710,5 87 133 5 pcs. 179 179 69810,7 94 142 – 69910,9 94 142 – 20911,0 94 142 – 180 180 70311,2 94 142 – 204 70611,5 94 142 – 205 213 70812,0 101 151 – 181 181 71213,0 101 151 – 182 18214,0 108 160 – 160 18315,0 114 169 – 184

Short Twist Drills10210 - 10214 DIN338




ATORN‘s taps:



ß

www.hhw.de 10.17

1

eng/OP

Cutting

High-Performance Short-Chip Drill X-DRILL

0TypeSpecial profile. Low wear of the cutting edges.Temperature-resistant.QualityPM/TiN for multi-purpose use.

Note: High true-running accuracy, long service life andgood dimensional accuracy. Short chips. Drillingwithout centring. Drills for production.

10215

HSS-E-PMd1h8 l2 l1 10215 …mm mm mm1,0 34 12 0101,1 36 14 0111,2 38 16 0121,3 38 16 0131,4 40 18 0141,5 40 18 0151,6 43 20 0161,7 43 20 0171,8 46 22 0181,9 46 22 0192,0 49 24 0202,1 49 24 0212,2 53 27 0222,3 53 27 0232,4 57 30 0242,5 57 30 0252,6 57 30 0262,7 61 33 0272,8 61 33 0282,9 61 33 0293,0 61 33 0303,1 65 36 0313,2 65 36 0323,3 65 36 0333,4 70 39 0343,5 70 39 0353,6 70 39 0363,7 70 39 0373,8 75 43 0383,9 75 43 0394,0 75 43 040


HSS-E-PMd1h8 l2 l1 10215 …mm mm mm7,2 109 69 0727,3 109 69 0737,4 109 69 0747,5 109 69 0757,6 117 75 0767,7 117 75 0777,8 117 75 0787,9 117 75 0798,0 117 75 0808,1 117 75 0818,2 117 75 0828,3 117 75 0838,4 117 75 0848,5 117 75 0858,8 125 81 0889,0 125 81 0909,3 125 81 0939,5 125 81 0959,8 133 87 098

10,0 133 87 10010,3 133 87 10310,5 133 87 10511,0 142 94 11011,5 142 94 11512,0 151 101 12012,5 151 101 12512,7 151 101 12713,0 160 108 13013,5 160 108 13514,0 160 108 140

10215

Al<10%Si Al>10%Si Cu St<520N St<750N St<900N St<1100N St<1200N St<1400N <45HRC <55HRC <60HRC <67HRC VA-steel<900N VA-steel>900N Ti alloys GG(G) plastics80-90 80-90 60-65 50-60 40-50 30-50 25-45 25-45 20-28 - - - - 15-18 10-15 - 40-60 25-30

DIN338






900N VA-steel>900N0 15-40



• Miniature drills • Sheet metal drills • Twist drills

www.hhw.de10.18

1

eng/OP

Miniature Drills

TTypeSpecial drill with reinforced shank, high true-runningaccuracy and precisely ground point angle. Up to drill Ø 0,79 = shank Ø 1 mm,starting at drill Ø 0,90 = shaft Ø 1,5 mm.

QualityHSS-E ground for multi-purpose use and forsteel with a strength of up to 1400 N/mm2.

Note: Overall length 25 mm for all sizes.

10220

10220

HSS-Ed1 l 10220 …

mm mm a0,16 1,1 10 pcs. 1020,17 1,1 10 pcs. 1030,18 1,1 10 pcs. 1040,19 1,1 10 pcs. 1050,20 1,5 10 pcs. 1060,21 1,5 10 pcs. 1070,22 1,5 10 pcs. 1080,23 1,5 10 pcs. 1090,24 1,5 10 pcs. 1100,25 1,9 10 pcs. 1110,26 1,9 10 pcs. 1120,27 1,9 10 pcs. 1130,28 1,9 10 pcs. 1140,29 1,9 10 pcs. 1150,30 1,9 10 pcs. 1160,32 2,4 10 pcs. 1180,33 2,4 10 pcs. 119

HSS-Ed1 l 10220 …


HSS-Ed1 l 10220 …


HSS-Ed1 l 10220 …



Double-Sided Sheet Metal Drills

ßTypeGround on both sides, extremely break-proof thanksto shortened flutes. Especially suitable for hand-guided machines. Special-treated surface.QualityHSS ground.

Note: Especially for drilling in thin sheet metal.

HSSd1 h8 l2 l1 10250 …

mm mm mm a2,5 9,5 43 10 pcs. 1043,0 10,6 46 10 pcs. 1053.1 11,2 49 10 pcs. 1063,2 11,2 49 10 pcs. 1073,3 11,2 49 10 pcs. 108

HSSd1 h8 l2 l1 10250 …

mm mm mm a3,8 14,0 55 10 pcs. 1114,0 14,0 55 10 pcs. 1134,1 14,0 55 10 pcs. 1144,2 14,0 55 10 pcs. 1155,0 17,0 62 10 pcs. 117

10250

l1=25mm

l

d1

d1

l2l1

10250

Precision Short Chucks Cooling units see page 21.8 cont.

HSS-E

HSS

DIN1899




ß

www.hhw.de 10.19

1

eng/OP

Cutting

Extra Short Twist Drills10252 - 10257

0TypeStraight shank, right-hand cut,relieved cone grind.

Note: High true-running accuracy. Long service life. Drills for production.

10252 Quality HSS ground for steel with a strength of up to 900 N/mm2.

10257 QualityHSS-E with reinforced core and web-thinning for VA-steel.

10255 Quality HSS-E/TiN with special web-thinning smoothdrilling and highest service life in VA-steel,spring steel, and special alloys such as Hastel-loy, Nimonic and Inconel.

10252

10257

10255

d1

l2l1

HSS HSS-E HSS-E/TiNd1 h8 l2 10252 … 10257 … 10255 …mm mm a1,00 6 10 pcs. 610 640 3101,10 7 10 pcs. 612 6461,20 8 10 pcs. 613 652 3121,30 8 10 pcs. 615 6551,40 9 10 pcs. 617 658 3141,50 9 10 pcs. 619 661 3151,60 10 10 pcs. 622 664 3161,70 10 10 pcs. 6671,80 11 10 pcs. 626 670 3181,90 11 10 pcs. 628 6762,00 12 10 pcs. 630 679 3202,10 12 10 pcs. 632 682 3212,20 13 10 pcs. 634 685 3222,30 13 10 pcs. 636 6912,40 14 10 pcs. 638 694 3242,50 14 10 pcs. 640 697 3252,60 14 10 pcs. 642 700 3262,70 16 10 pcs. 644 703 3272,80 16 10 pcs. 646 706 3282,90 16 10 pcs. 647 7113,00 16 10 pcs. 649 714 3303,10 18 10 pcs. 651 7173,20 18 10 pcs. 652 720 3323,25 18 10 pcs. 7233,30 18 10 pcs. 654 726 3333,40 20 10 pcs. 655 729 3343,50 20 10 pcs. 657 732 3353,60 20 10 pcs. 658 735 3363,70 20 10 pcs. 659 7383,80 22 10 pcs. 661 741 3383,90 22 10 pcs. 663 7434,00 22 10 pcs. 664 746 3404,10 22 10 pcs. 665 749 3414,20 22 10 pcs. 666 752 3424,30 24 10 pcs. 668 758 3434,40 24 10 pcs. 7614,50 24 10 pcs. 672 764 3454,60 24 10 pcs. 7674,70 24 10 pcs. 675 7734,80 26 10 pcs. 677 7764,90 26 10 pcs. 679 7795,00 26 10 pcs. 681 782 3505,10 26 10 pcs. 682 785 3515,20 26 10 pcs. 683 788 3525,30 26 10 pcs. 685 7915,40 26 10 pcs. 686 7945,50 28 10 pcs. 687 797 355

HSS-E HSS-E HSS-E/TiNd1 h8 l2 10252 … 10257 … 10255 …mm mm a5,55 28 10 pcs. 8005,60 28 10 pcs. 8035,80 28 10 pcs. 691 3586,00 28 10 pcs. 694 815 3606,10 31 – 695 8186,20 31 – 697 8216,30 31 – 699 8246,40 31 – 701 8276,50 31 – 702 830 3656,60 31 – 703 833 3666,80 34 – 706 840 3686,90 34 – 8437,00 34 – 708 846 3707,10 34 – 709 3717,30 34 – 8557,40 34 – 8587,50 34 – 715 861 3757,80 37 – 719 870 3787,90 37 – 720 8738,00 37 – 721 876 3808,10 37 – 722 879 3818,20 37 – 723 882 3828,40 37 – 727 3848,50 37 – 728 890 3858,80 40 – 3888,90 40 – 8989,00 40 – 736 900 3909,10 40 – 9029,40 40 – 9089,50 40 – 743 9109,60 43 – 9129,70 43 – 9149,80 43 – 916

10,00 43 – 749 920 40010,20 43 – 752 40210,50 43 – 756 930 40511,00 47 – 761 936 41011,10 47 – 93811,50 47 – 765 946 41511,80 47 – 94812,00 51 – 769 950 42012,50 51 – 772 956 42512,80 51 – 95813,00 51 – 777 960 43013,50 54 – 779 96414,00 54 – 783 96614,50 56 – 786 968

HSS

HSS-E

HSS-ETiN



DIN1897

VA

continuation .


• Twist drills

www.hhw.de10.20

1

eng/OP

10255 - 10257Al<10%Si Al>10%Si Cu St<520N St<750N St<900N St<1100N St<1200N St<1400N <45HRC <55HRC <60HRC <67HRC VA-steel<900N VA-steel>900N Ti alloys GG(G) plastics

60-70 50-55 32-38 32-36 28-32 25-28 15+23 14-18 - - - - - 12-14 8-10 - 22-30 15-18


- - - 32-38 30-34 28-36 22-30 20-28 15-20 - - - - - - - 23-32 25-28

HSS HSS-E HSS-E/TiNd1 h8 l2 10252 … 10257 … 10255 …mm mm a

15,00 56 – 788 97016,00 58 – 794 97416,50 60 – 796 97617,00 60 – 79817,50 62 – 79918,00 62 – 800 98218,50 64 – 805 984

HSS HSS-E HSS-E/TiNd1 h8 l2 10252 … 10257 … 10255 …mm mm a

19,00 64 – 807 98619,50 66 – 98820,00 66 – 810 99021,00 68 – 81222,00 70 – 81425,00 75 – 816

Multi-Purpose Twist Drills MBS 1200

10259

10259

0TypeStraight shank, right-hand cut, relieved cone grind.Special web-thinning. 4 surfaces pre-ground.QualityHSS-E ground for multi-purpose use in VA-steel,steel with a strength of up to 1200 N/mm2, castiron and aluminium.

Note: Multi-purpose use, quiet drilling, low torque, highdimensional accuracy, perfect chip removal thanksto the round flute profile.

Al<10%Si Al>10%Si Cu St<520N St<750N St<900N St<1100N St<1200N St<1400N <45HRC <55HRC <60HRC <67HRC VA-steel<900N VA-steel>900N Ti alloys GG(G) plastics50-60 30-40 40-50 35-42 32-40 28-28 16-20 15-18 - - - - - 18-20 14-16 6-8 25-50 25-32

HSS-Ed1 l2 l1 10259 …

mm mm mm a1,0 6 26 10 pcs. 3011,1 7 28 10 pcs. 3021,2 8 30 10 pcs. 3031,3 8 30 10 pcs. 3041,4 9 32 10 pcs. 3051,5 9 32 10 pcs. 3061,6 10 34 10 pcs. 3071,7 10 34 10 pcs. 3081,8 11 36 10 pcs. 3091,9 11 36 10 pcs. 3102,0 12 38 10 pcs. 3112,1 12 38 10 pcs. 3122,2 13 40 10 pcs. 3132,3 13 40 10 pcs. 3142,4 14 43 10 pcs. 3152,5 14 43 10 pcs. 3162,6 14 43 10 pcs. 3172,7 16 46 10 pcs. 3182,8 16 46 10 pcs. 3192,9 16 46 10 pcs. 3203,0 16 46 10 pcs. 3213,1 18 49 10 pcs. 3223,2 18 49 10 pcs. 3233,3 18 49 10 pcs. 3243,4 20 52 10 pcs. 3253,5 20 52 10 pcs. 3263,6 20 52 10 pcs. 3273,7 20 52 10 pcs. 3283,8 22 55 10 pcs. 3293,9 22 55 10 pcs. 3304,0 22 55 10 pcs. 331

HSS-Ed1 l2 l1 10259 …

mm mm mm a4,1 22 55 10 pcs. 3324,2 22 55 10 pcs. 3334,3 24 58 10 pcs. 3344,4 24 58 10 pcs. 3354,5 24 58 10 pcs. 3364,6 24 58 10 pcs. 3374,7 24 58 10 pcs. 3384,8 26 62 10 pcs. 3394,9 26 62 10 pcs. 3405,0 26 62 10 pcs. 3415,1 26 62 10 pcs. 3425,2 26 62 10 pcs. 3435,3 26 62 10 pcs. 3445,4 28 66 10 pcs. 3455,5 28 66 10 pcs. 3465,6 28 66 10 pcs. 3475,7 28 66 10 pcs. 3485,8 28 66 10 pcs. 3495,9 28 66 10 pcs. 3506,0 28 66 10 pcs. 3516,1 31 70 – 3526,2 31 70 – 3536,3 31 70 – 3546,4 31 70 – 3556,5 31 70 – 3566,6 31 70 – 3576,7 31 70 – 3586,8 34 74 – 3596,9 34 74 – 3607,0 34 74 – 3617,1 34 75 – 362

HSS-Ed1 l2 l1 10259 …

mm mm mm a7,2 34 75 – 3637,3 34 75 – 3647,4 34 75 – 3657,5 34 74 – 3667,6 37 79 – 3677,7 37 79 – 3687,8 37 79 – 3697,9 37 79 – 3708,0 37 79 – 3718,1 37 79 – 3728,2 37 79 – 3738,3 37 79 – 3748,4 37 79 – 3758,5 37 79 – 3768,8 40 84 – 3779,0 40 84 – 3789,3 40 84 – 3799,5 40 84 – 3809,8 43 89 – 381

10,0 43 89 – 38210,2 43 89 – 38310,5 43 89 – 38411,0 47 95 – 38511,5 47 95 – 38612,0 51 102 – 38712,5 51 102 – 38813,0 51 102 – 38913,5 54 107 – 39014,0 54 107 – 391

HSS-EDIN1897

d1

l

l2

1

Extra Short Twist Drills10252 - 10257 DIN1897




ß

www.hhw.de 10.21

1

eng/OP

Cutting

VA-Steel Twist Drill

TypeNC shank. Dimensions similar to DIN 1897. Special profile.QualityHSS-E-Co/TiAlN.

Note: High true-running accuracy, long service life andgood dimensional accuracy. Solves all problemswith VA-steel materials. Drills for production. Drilling without centring.

10260

10260

HSS-E/TiAlNd1 h8 l2 l1 d2 h6 10260 …

mm mm mm mm1,0 6 26 3 0801,1 7 28 3 0811,2 8 30 3 0821,3 8 30 3 0831,4 9 32 3 0841,5 9 32 3 0851,6 10 34 3 0861,7 10 34 3 0871,8 11 36 3 0881,9 11 36 3 0892,0 12 38 3 0902,1 12 38 3 0912,2 13 40 3 0922,3 13 40 3 0932,4 14 43 3 0942,5 14 43 3 0952,6 14 43 3 0962,7 16 46 3 0972,8 16 46 3 0982,9 16 46 3 1003,0 16 46 3 1013,1 18 49 4 1023,2 18 49 4 1033,3 18 49 4 1043,4 20 52 4 1053,5 20 52 4 1063,6 20 52 4 1073,7 20 52 4 1083,8 22 55 4 1093,9 22 55 4 1104,0 22 55 4 1114,1 22 55 6 1124,2 22 55 6 1134,3 24 58 6 1144,4 24 58 6 1154,5 24 58 6 1164,6 24 58 6 1174,7 24 58 6 1184,8 26 62 6 1194,9 26 62 6 1205,0 26 62 6 1215,1 26 62 6 1225,2 26 62 6 1235,3 26 62 6 1245,4 28 66 6 1255,5 28 66 6 126


mm mm mm mm5,6 28 66 6 1275,7 28 66 6 1285,8 28 66 6 1295,9 28 66 6 1306,0 28 66 6 1316,1 32 70 8 1326,2 32 70 8 1336,3 32 70 8 1346,4 32 70 8 1356,5 32 70 8 1366,6 32 70 8 1376,7 32 70 8 1386,8 34 74 8 1396,9 34 74 8 1407,0 34 74 8 1417,1 34 74 8 1427,2 34 74 8 1437,3 34 74 8 1447,4 34 74 8 1457,5 34 74 8 1467,6 37 79 8 1477,7 37 79 8 1487,8 37 79 8 1497,9 37 79 8 1508,0 37 79 8 1518,1 37 79 10 1528,2 37 79 10 1538,3 37 79 10 1548,4 37 79 10 1558,5 37 79 10 1568,6 40 84 10 1578,7 40 84 10 1588,8 40 84 10 1598,9 40 84 10 1609,0 40 84 10 1619,1 40 84 10 1629,2 40 84 10 1639,3 40 84 10 1649,4 40 84 10 1659,5 40 84 10 1669,6 43 89 10 1679,7 43 89 10 1689,8 43 89 10 1699,9 43 89 10 170

10,0 43 89 10 17110,1 43 89 10 172


mm mm mm mm10,2 43 89 10 17310,3 43 89 10 17410,4 43 89 10 17510,5 43 89 10 17610,6 47 95 12 17710,7 47 95 12 17810,8 47 95 12 18010,9 47 95 12 18111,0 47 95 12 18211,1 47 95 12 18311,2 47 95 12 18411,3 47 95 12 18511,4 47 95 12 18611,5 47 95 12 18711,6 47 95 12 18811,7 47 95 12 18911,8 47 95 12 19011,9 47 95 12 19112,0 51 102 12 19212,1 51 102 12 19312,2 51 102 12 19412,3 51 102 12 19512,4 51 102 12 19612,5 51 102 12 19712,6 51 102 12 19812,7 51 102 12 19912,8 51 102 12 20012,9 51 102 12 20113,0 51 102 12 20213,5 54 107 16 20314,0 54 107 16 20414,5 56 111 16 20515,0 56 111 16 206

15,25 58 115 16 20715,3 58 115 16 20815,5 58 115 16 20916,0 58 115 16 21016,5 60 119 20 21117,0 60 119 20 21217,5 62 123 20 21318,0 62 123 20 21418,5 64 127 20 21519,0 64 127 20 21619,5 66 131 20 21720,0 66 131 20 218

Al<10%Si Al>10%Si Cu St<520N St<750N St<900N St<1100N St<1200N St<1400N <45HRC <55HRC <60HRC <67HRC VA-steel<900N VA-steel>900N Ti alloys GG(G) plastics80-100 63-90 25-50 32-45 34-40 22-28 22-25 18-22 15-18 - - - - 13-18 8-12 - 32-40 -

VAHSS-ETiAIN

DIN1897


Solid carbide high-performance twist drills by ATORN:



• Short-chip drill • Twist drills

www.hhw.de10.22

1

eng/OP

High-Performance Short-Chip Drill X-DRILL

0TypeSpecial profile. Low wear of the cutting edges.Temperature-resistant.QualityPM/TiN for multi-purpose use.

Note: High true-running accuracy, long service life andgood dimensional accuracy. Short chips. Drillingwithout centring. Drills for production.

10261



HSS-E-PMd1h8 l2 l1 10261 …mm mm mm7,2 74 34 0727,3 74 34 0737,4 74 34 0747,5 74 34 0757,6 79 37 0767,7 79 37 0777,8 79 37 0787,9 79 37 0798,0 79 37 0808,1 79 37 0818,2 79 37 0828,3 79 37 0838,4 79 37 0848,5 79 37 0858,8 84 40 0889,0 84 40 0909,3 84 40 0939,5 84 40 0959,8 89 43 098

10,0 89 43 10010,2 89 43 10210,5 89 43 10511,0 95 47 11011,5 95 47 11512,0 102 51 12012,3 102 51 12312,5 102 51 12512,7 102 51 12713,0 102 51 13013,5 107 54 13514,0 107 54 140

10261


DIN1897






900N VA-steel>900N0 15-40



ß

www.hhw.de 10.23

1

eng/OP

Cutting

Long Twist Drills

0TypeStraight shank, right-hand cut, relieved cone grind.Web-thinned chisel edge.

10406 Quality HSS ground for standard-duty materials with a strength of up to 1200 N/mm2.

10404 Quality HSS-E ground for difficult to machine materialssuch as VA-steel, titanium, and exotic materials.

10404

HSS HSS-Ed1 h8 l2 l1 10406 … 10404 …mm mm mm a0,60 15 35 10 pcs. 6060,80 29 46 10 pcs. 6081,00 33 56 10 pcs. 610 1101,10 37 60 10 pcs. 611 1111,20 41 65 10 pcs. 613 1121,30 41 65 10 pcs. 615 1131,40 45 70 10 pcs. 616 1141,50 45 70 10 pcs. 617 1151,60 50 76 10 pcs. 619 1161,70 50 76 10 pcs. 620 1171,80 53 80 10 pcs. 622 1181,90 53 80 10 pcs. 623 1192,00 56 85 10 pcs. 625 1202,10 56 85 10 pcs. 627 1212,20 59 90 10 pcs. 628 1222,30 59 90 10 pcs. 630 1232,40 62 95 10 pcs. 631 1242,50 62 95 10 pcs. 632 1252,60 62 95 10 pcs. 634 1262,70 66 100 10 pcs. 636 1272,80 66 100 10 pcs. 637 1282,90 66 100 10 pcs. 639 1293,00 66 100 10 pcs. 640 1303,10 69 106 10 pcs. 642 1313,20 69 106 10 pcs. 644 1323,30 69 106 10 pcs. 646 1333,40 73 112 10 pcs. 648 1343,50 73 112 10 pcs. 649 1353,60 73 112 10 pcs. 650 1363,70 73 112 10 pcs. 651 1373,80 78 119 10 pcs. 653 1383,90 78 119 10 pcs. 654 1394,00 78 119 10 pcs. 655 1404,10 78 119 10 pcs. 657 1414,20 78 119 10 pcs. 658 1424,30 82 126 10 pcs. 660 143

HSS HSS-Ed1 h8 l2 l1 10406 … 10404 …mm mm mm a4,40 82 126 10 pcs. 661 1444,50 82 126 10 pcs. 662 1454,60 82 126 10 pcs. 6634,70 82 126 10 pcs. 664 1474,80 87 132 10 pcs. 666 1484,90 87 132 10 pcs. 668 1495,00 87 132 10 pcs. 669 1505,10 87 132 10 pcs. 671 1515,20 87 132 10 pcs. 673 1525,30 87 132 10 pcs. 675 1535,40 91 139 10 pcs. 676 1545,50 91 139 10 pcs. 678 1555,60 91 139 10 pcs. 679 1565,70 91 139 10 pcs. 680 1575,80 91 139 10 pcs. 682 1585,90 91 139 10 pcs. 683 1596,00 91 139 10 pcs. 684 1606,10 97 148 – 685 1616,20 97 148 – 686 1626,30 97 148 – 688 1636,40 97 148 – 689 1646,50 97 148 – 690 1656,60 97 148 – 691 1666,70 97 148 – 692 1676,80 102 156 – 694 1686,90 102 156 – 6957,00 102 156 – 696 1707,10 102 156 – 6977,20 102 156 – 6987,30 102 156 – 6997,40 102 156 – 7007,50 102 156 – 701 1757,60 109 165 – 7027,70 109 165 – 703 1777,80 109 165 – 704 1787,90 109 165 – 705

10406

10404 - 10406

HSS HSS-Ed1 h8 l2 l1 10406 … 10404 …mm mm mm a8,00 109 165 – 706 1808,10 109 165 – 707 1818,20 109 165 – 708 1828,30 109 165 – 7098,40 109 165 – 710 1848,50 109 165 – 711 1858,60 115 175 – 7128,70 115 175 – 7138,80 115 175 – 7148,90 115 175 – 7159,00 115 175 – 716 1909,10 115 175 – 7179,20 115 175 – 7189,30 115 175 – 7199,40 115 175 – 7209,50 115 175 – 7219,60 121 184 – 7229,70 121 184 – 7239,80 121 184 – 724 1989,90 121 184 – 725

10,00 121 184 – 726 20010,20 121 184 – 728 20210,25 121 184 – 72910,50 121 184 – 732 20511,00 128 195 – 737 21011,50 128 195 – 742 21512,00 134 205 – 747 22012,50 134 205 – 75213,00 134 205 – 75713,50 140 214 – 76214,00 140 214 – 76314,50 144 220 – 76415,00 144 220 – 76515,50 149 227 – 76616,00 149 227 – 767


- - - 24-30 22-27 21-25 - - - - - - - 12-16 10-12 0-12 18-22 14-22


60-70 50-55 32-36 30-40 25-28 15-28 15-22 14-18 - - - - - 12-14 - 6-10 - 15-18

HSS-E

HSS

DIN340

VA



d1

l2l1


• Deep hole drill • Twist drills

www.hhw.de10.24

1

eng/OP

Deep Hole Drill

TypeStraight shank, right-hand cut, relieved cone grind.Web-thinned chisel edge, reinforced core, wideflutes and very rounded heels.

Note: For drilling deep holes (5-10 x d) without chipremoval.

10407ß

QualityHSS ground for standard-duty materials with a strength of up to 900 N/mm2.

10408 T

QualityHSS ground with polished flutes for perfect chiptransport in soft materials.

10407

Type FS Type FWd1 h8 l2 l1 10407 … 10408 …mm mm mm a1,0 33 56 10 pcs. 2011,1 37 60 10 pcs. 2071,2 41 65 10 pcs. 2111,3 41 65 10 pcs. 2131,4 45 70 10 pcs. 2161,5 45 70 10 pcs. 2181,6 50 76 10 pcs. 2231,7 50 76 10 pcs. 2261,8 53 80 10 pcs. 2291,9 53 80 10 pcs. 2312,0 56 85 10 pcs. 236 1112,1 56 85 10 pcs. 240 1122,2 59 90 10 pcs. 2432,3 59 90 10 pcs. 2462,4 62 95 10 pcs. 250 1152,5 62 95 10 pcs. 254 1162,6 62 95 10 pcs. 2582,7 66 100 10 pcs. 2612,8 66 100 10 pcs. 266 1192,9 66 100 10 pcs. 270 1203,0 66 100 10 pcs. 273 1213,1 69 106 10 pcs. 275 1223,2 69 106 10 pcs. 278 1233,3 69 106 10 pcs. 281 1243,4 73 112 10 pcs. 282 1253,5 73 112 10 pcs. 284 1263,6 73 112 10 pcs. 2873,7 73 112 10 pcs. 2903,8 78 119 10 pcs. 293 1293,9 78 119 10 pcs. 295 1304,0 78 119 10 pcs. 299 131

Type FS Type FWd1 h8 l2 l1 10407 … 10408 …mm mm mm a4,2 78 119 10 pcs. 305 1334,5 82 126 10 pcs. 312 1364,8 87 132 10 pcs. 3195,0 87 132 10 pcs. 324 1415,1 87 132 10 pcs. 1425,2 87 132 10 pcs. 3305,5 91 139 10 pcs. 337 1465,8 91 139 10 pcs. 3446,0 91 139 10 pcs. 347 1516,2 97 148 10 pcs. 3526,5 97 148 10 pcs. 357 1566,8 102 156 5 pcs. 363 1597,0 102 156 5 pcs. 366 1617,2 102 156 5 pcs. 3717,5 102 156 5 pcs. 3767,8 109 165 5 pcs. 3827,9 109 165 5 pcs. 1708,0 109 165 5 pcs. 386 1718,2 109 165 5 pcs. 3898,5 109 165 5 pcs. 3959,0 115 175 5 pcs. 4039,5 115 175 5 pcs. 412 1869,8 121 184 5 pcs. 417

10,0 121 184 5 pcs. 420 19110,5 121 184 5 pcs. 42911,0 128 195 – 43311,5 128 195 – 43812,0 134 205 – 44212,5 134 205 – 44413,0 134 205 – 447

10408

d1

l2l1

10407 - 10408

d1

l2l1


45-55 35-45 25-30 25-30 22-28 21-25 18-20 - - - - - - - - - 18-22 14-2210408

Al<10%Si Al>10%Si Cu St<520N St<750N St<900N St<1100N St<1200N St<1400N <45HRC <55HRC <60HRC <67HRC VA-steel<900N VA-steel>900N Ti alloys GG(G) plastics40-55 40-45 25-28 - - - - - - - - - - - - - - -

FS

HSS

FW

DIN340


Roughing end milling cutter by ATORN:

ATORN‘s high-quality milling tools.




ß

www.hhw.de 10.25

1

eng/OP

Cutting

Long Twist Drills

0TypeStraight shank, right-hand cut, relieved cone grind.Web-thinned chisel edge, reinforced core, and veryrounded heels.Quality HSS/TiN-coated for long service lifein steel with a strength of up to 1000 N/mm2 and

cast iron.Note: For drilling deep holes under extreme conditions,e.g. poor chip removal, insufficient cooling.

Warning:Exception: VA-steel, CrN-steel, and similar materi-als.

10410

HSS/TiNd1 h8 l2 l1 10410 …

mm mm mm a1,0 33 56 10 pcs. 1101,1 37 60 10 pcs. 1111,2 41 65 10 pcs. 1121,3 41 65 10 pcs. 1131,4 45 70 10 pcs. 1141,5 45 70 10 pcs. 1151,6 50 76 10 pcs. 1161,7 50 76 10 pcs. 1171,8 53 80 10 pcs. 1181,9 53 80 10 pcs. 1192,0 56 85 10 pcs. 1202,1 56 85 10 pcs. 1212,2 59 90 10 pcs. 1222,3 59 90 10 pcs. 1232,4 62 95 10 pcs. 1242,5 62 95 10 pcs. 1252,6 62 95 10 pcs. 1262,7 66 100 10 pcs. 1272,8 66 100 10 pcs. 1282,9 66 100 10 pcs. 1293,0 66 100 10 pcs. 1303,1 69 106 10 pcs. 1313,2 69 106 10 pcs. 1323,3 69 106 10 pcs. 133

HSS/TiNd1 h8 l2 l1 10410 …

mm mm mm a3,4 73 112 10 pcs. 1343,5 73 112 10 pcs. 1353,6 73 112 10 pcs. 1363,7 73 112 10 pcs. 1373,8 78 119 10 pcs. 1383,9 78 119 10 pcs. 1394,0 78 119 10 pcs. 1404,1 78 119 10 pcs. 1414,2 78 119 10 pcs. 1424,3 82 126 10 pcs. 1434,4 82 126 10 pcs. 1444,5 82 126 10 pcs. 1454,7 82 126 10 pcs. 1474,8 87 132 10 pcs. 1484,9 87 132 10 pcs. 1495,0 87 132 10 pcs. 1505,1 87 132 10 pcs. 1515,2 87 132 10 pcs. 1525,3 87 132 10 pcs. 1535,4 91 139 10 pcs. 1545,5 91 139 10 pcs. 1555,6 91 139 10 pcs. 1565,7 91 139 10 pcs. 1575,8 91 139 10 pcs. 158

HSS/TiNd1 h8 l2 l1 10410 …

mm mm mm a5,9 91 139 10 pcs. 1596,0 91 139 10 pcs. 1606,1 97 148 – 1616,2 97 148 – 1626,3 97 148 – 1636,4 97 148 – 1646,5 97 148 – 1656,6 97 148 – 1666,7 97 148 – 1676,8 102 156 – 1687,0 102 156 – 1707,5 102 156 – 1758,0 109 165 – 1808,5 109 165 – 1859,0 115 175 – 1909,5 115 175 – 195

10,0 121 184 – 20010,2 121 184 – 20210,5 121 184 – 20511,0 128 195 – 21011,5 128 195 – 21512,0 134 205 – 220

d1

l2l1

10410

Al<10%Si Al>10%Si Cu St<520N St<750N St<900N St<1100N St<1200N St<1400N <45HRC <55HRC <60HRC <67HRC VA-steel<900N VA-steel>900N Ti alloys GG(G) plastics45-55 30-45 22-28 32-40 28-32 25-28 18-25 - - - - - - - - - 25-38 -

DIN340



HSS HSS/TiNd1 h8 x l1 l2 10421 … 10422 …

mm mm2,0 x 125 85 101 1012,5 x 140 95 102 1023,0 x 150 100 103 1033,0 x 190 130 1043,5 x 165 115 1053,5 x 210 145 1064,0 x 175 120 108 1084,0 x 220 150 109 1094,0 x 280 190 1104,5 x 185 125 1114,5 x 235 160 1125,0 x 195 135 114 1145,0 x 245 170 1155,0 x 315 210 116

HSS HSS/TiNd1 h8 x l1 l2 10421 … 10422 …

mm mm5,5 x 205 140 1175,5 x 260 180 1186,0 x 205 140 120 1206,0 x 260 180 1216,0 x 330 225 1226,5 x 215 150 1236,5 x 275 190 1247,0 x 225 155 1267,0 x 290 200 127 1277,0 x 370 250 1287,5 x 225 155 1297,5 x 290 200 1308,0 x 240 165 132 1328,0 x 305 210 133 133

HSS HSS/TiNd1 h8 x l1 l2 10421 … 10422 …

mm mm8,0 x 390 265 1348,5 x 240 165 1358,5 x 305 210 136 1368,5 x 390 265 1379,0 x 250 175 1389,0 x 320 220 1399,0 x 410 280 1409,5 x 250 175 141

10,0 x 265 185 14410,0 x 340 235 14510,0 x 430 295 14611,0 x 280 195 14712,0 x 375 260 14812,0 x 375 260 148

Extra Long Twist Drill

TTypeStraight shank, right-hand cut, relieved cone grind.Web-thinned chisel edge.

10421 Quality Flat, wide flutes for boreholes up to 10 x D withoutchip removal, rounded heels, starting at 2,5 mm withnitrided lands. HSS ground for steel with a strengthof up to 1000 N/mm2, cast iron, aluminium alloys,brass, and bronze.

10422 QualityReinforced core and very rounded heels, formachining under extreme conditions such as poorchip removal and insufficient cooling. HSS/TiN-coat-ed for long service life in steel with a strength of upto 1000 N/mm2 and cast iron.

Warning:Exception: VA-steel, CrN-steel, and similar materi-als.

10421

10422

d1

l2l1

10421 - 10422


40-45 30-36 18-22 18-22 18-22 14-18 12-16 6-10 - - - - - 6-8 - - 14-22 12-1810422

Al<10%Si Al>10%Si Cu St<520N St<750N St<900N St<1100N St<1200N St<1400N <45HRC <55HRC <60HRC <67HRC VA-steel<900N VA-steel>900N Ti alloys GG(G) plastics45-50 40-45 22-28 22-28 16-20 10-15 8-12 - - - - - - 8-10 - 4-6 18-25 15-22

DIN1869Reihe 1, 2, 3


• Twist drills

www.hhw.de10.26

1

eng/OP

Twist Drills with Morse Taper Shanks

TypeRelieved cone grind, surface-treated, this reducesthe tendency of the machined material to stick to themachining tool and improves chip removal.

10508

0QualityHSS ground for steel with a strength of up to 900N/mm2, cast iron, aluminium alloys, brass, andbronze.

Note:Quality drill to satisfy the highest requirements. Drills for production.

10510 QualityHSS precision-rolled, for steel with a strength ofup to 800 N/mm2, cast iron, aluminium alloys,brass, and bronze.Note:Budget-priced.

10508

10510

0

d1 h8 l2 l1 10508 … 10510 …mm mm mm MT5,00 52 133 1 6045,50 57 138 1 6056,00 57 138 1 6066,50 63 144 1 6087,00 69 150 1 6138,00 75 156 1 6178,50 75 156 1 6199,00 81 162 1 6219,50 81 162 1 622

10,00 87 168 1 624 21110,20 87 168 1 626 21210,50 87 168 1 629 21310,80 94 175 1 63011,00 94 175 1 631 21511,20 94 175 1 21611,50 94 175 1 634 21711,80 94 175 1 636 21812,00 101 182 1 637 21912,20 101 182 1 639 22012,50 101 182 1 640 22112,80 101 182 1 64113,00 101 182 1 642 22313,50 108 189 1 645 22513,80 108 189 1 64714,00 108 189 1 648 22714,25 114 212 2 651 22814,50 114 212 2 652 22914,75 114 212 2 654 23015,00 114 212 2 655 23115,25 120 218 2 656 23215,50 120 218 2 657 23315,75 120 218 2 658 23416,00 120 218 2 659 23516,25 125 223 2 661 23616,50 125 223 2 662 23716,75 125 223 2 664 23817,00 125 223 2 665 23917,25 130 228 2 666 24017,50 130 228 2 667 24117,75 130 228 2 668 24218,00 130 228 2 669 24318,25 135 233 2 670 24418,50 135 233 2 671 24518,75 135 233 2 672 24619,00 135 233 2 673 24719,25 140 238 2 24819,50 140 238 2 675 24919,75 140 238 2 676 25020,00 140 238 2 677 25120,25 145 243 2 679 25220,50 145 243 2 681 25320,75 145 243 2 682 25421,00 145 243 2 683 25521,25 150 248 2 25621,50 150 248 2 685 25721,75 150 248 2 686 258

0

d1 h8 l2 l1 10508 … 10510 …mm mm mm MT

22,00 150 248 2 687 25922,25 150 248 2 26022,50 155 253 2 689 26122,75 155 253 2 26223,00 155 253 2 691 26323,50 155 276 3 693 26524,00 160 281 3 695 26724,50 160 281 3 696 26824,75 160 281 3 69725,00 160 281 3 698 27025,50 165 286 3 701 27126,00 165 286 3 703 27326,50 165 286 3 704 27427,00 170 291 3 706 27627,50 170 291 3 707 27728,00 170 291 3 709 27928,50 175 296 3 710 28029,00 175 296 3 711 28129,50 175 296 3 712 28230,00 175 296 3 713 28330,50 180 301 3 714 28431,00 180 301 3 715 28531,50 180 301 3 28632,00 185 334 4 717 28732,50 185 334 4 718 28833,00 185 334 4 719 28933,50 185 334 4 720 29034,00 190 339 4 721 29134,50 190 339 4 722 29235,00 190 339 4 723 29335,50 190 339 4 724 29436,00 195 344 4 725 29536,50 195 344 4 726 29637,00 195 344 4 727 29738,00 200 349 4 728 29838,50 200 349 4 729 29939,00 200 349 4 730 30039,50 200 349 4 731 30140,00 200 349 4 732 30241,00 205 354 4 733 30342,00 205 354 4 734 30443,00 210 359 4 735 30544,00 210 359 4 736 30645,00 210 359 4 737 30746,00 215 364 4 738 30847,00 215 364 4 739 30948,00 220 369 4 740 31049,00 220 369 4 741 31150,00 220 369 4 742 31251,00 225 412 5 74355,00 230 417 5 74756,00 230 417 5 74857,00 235 422 5 74958,00 235 422 5 75059,00 235 422 5 75160,00 235 422 5 752

d1

l2l1

10508 - 10510 HSSDIN345


55-63 40-50 25-32 25-32 25-32 20-25 15-18 14-16 - - - - - - - - 20-28 16-25


- - - 25-32 25-32 20-25 15-18 14-16 - - - - - - - - 20-28 16-25


ß

www.hhw.de 10.27

1

eng/OP

Cutting

Twist Drills with Morse Taper Shanks

10511

10526

T 0 0

d1 h8 l2 l1 MT 10511 … 10514 … 10526 …mm mm mm10,0 87 168 1 63010,2 87 168 1 63210,5 87 168 1 213 634

11,00 94 175 1 215 637 11111,5 94 175 1 217 639 11512,0 101 182 1 219 642 12012,5 101 182 1 221 647 12513,0 101 182 1 650 13013,5 108 189 1 225 653 135

13,75 108 189 1 65514,0 108 189 1 227 657 14014,5 114 212 2 229 662 14515,0 114 212 2 231 664 15015,5 120 218 2 666 15516,0 120 218 2 235 668 16016,5 125 223 2 670 16517,0 125 223 2 239 671 17017,5 130 228 2 241 673 17518,0 130 228 2 243 674 18018,5 135 233 2 676 18519,0 135 233 2 677 19019,5 140 238 2 678 19520,0 140 238 2 251 679 200

T 0 0

d1 h8 l2 l1 MT 10511 … 10514 … 10526 …mm mm mm20,5 145 238 2 680 20521,0 145 243 2 255 681 21021,5 150 248 2 682 21522,0 150 248 2 259 683 22022,5 155 253 2 261 684 22523,0 155 253 2 685 23023,5 155 276 3 68624,0 160 281 3 687 24024,5 160 281 3 688 24525,0 160 281 3 689 25026,0 165 286 3 273 692 26026,5 170 291 3 26527,0 170 291 3 694 27028,0 170 291 3 279 696 28028,5 175 296 3 28529,0 175 296 3 698 29030,0 175 296 3 700 30031,0 180 301 3 70232,0 185 334 4 704 32033,0 185 334 4 70534,0 190 339 4 70635,0 190 339 4 707

d1

l2l1

10511 - 10526

TypeRelieved cone grind. Web-thinned chisel edge.

Note:Quality drill to satisfy the highest requirements.

10511 T

QualityHSS/TiN for even longer service life in steel witha strength of up to 900 N/mm2, cast iron, alumini-um alloys, bronze, brass.

10514

0QualityHSS-E surface-treated for steel with a strengthof up to 1200 N/mm2 and cast iron. Reducedtendency of the machined material to stick to themachining tool and improved chip removal.Reinforced core.

10526

0QualityHSS-E with special design for VA-steel andmaterials which are subject to strain hardening.


60-70 45-55 26-36 28-36 22-28 22-26 16-18 12-20 - - - - - - - - 22-28 18-2810514

Al<10%Si Al>10%Si Cu St<520N St<750N St<900N St<1100N St<1200N St<1400N <45HRC <55HRC <60HRC <67HRC VA-steel<900N VA-steel>900N Ti alloys GG(G) plastics- - - 28-36 22-28 14-18 14-16 10-14 - - - - - 10-14 4-6 6-8 22-30 16-18


- - - 35-40 32-35 25-32 20-25 15-20 12-15 - - - - 10-15 10-15 8-10 - -

10514HSS-E

DIN345


Swivel bases by ATORN:

ATORN‘s high-quality turning tools.

HSS-E VA


• Twist drills • Core drills

www.hhw.de10.28

1

eng/OP

Long Twist Drill (Bushing Drill) with Morse Taper Shank

TTypeRelieved cone grind. Surface-treated, this reducestendency of the machined material to stick to themachining tool and improves chip removal. Startingat Ø 14 mm, web-thinned. Extended cutting edgecompared to DIN 345.QualityHSS ground for steel with a strength of up to 900N/mm2, cast iron, graphite.

Note: For drilling through bushings.

10610

HSSd1 h8 l2 l1 10610 …

mm mm mm MT10,0 116 197 1 12211,0 125 206 1 12711,5 125 206 1 12913,0 134 215 1 13513,5 142 223 1 13714,0 142 223 1 14015,0 147 245 2 14515,5 153 251 2 14716,0 153 251 2 14917,0 159 257 2 15517,5 165 263 2 157

HSSd1 h8 l2 l1 10610 …

mm mm mm MT18,0 165 263 2 15919,0 171 269 2 16220,0 177 275 2 16421,0 184 282 2 16622,0 191 289 2 16824,0 206 327 3 17225,0 206 327 3 17328,0 222 343 3 17630,0 230 351 3 17834,0 257 406 4 18235,0 257 406 4 183

d1

l2l1

10610

Extra Long Twist Drill with Morse Taper Shank

TTypeReinforced core, flat flute section, relieved conegrind and web-thinning. Up to Ø 16 mm with nitratedlands and bright flutes. Above that with special heattreatment for increased wear resistance andreduced tendency of the machined material to stickto the machining tool.QualityHSS ground for steel with a strength of up to 900N/mm2, cast iron, graphite, aluminium alloys,brass, bronze.

Note:For drilling boreholes with a diameter of up to 10 x D without chip removal.

10621

HSSd1 h8 x l1 l2 10621 …

mm mm MT8 x 265 165 1 1019 x 275 175 1 103

10 x 285 185 1 10510 x 360 235 1 10611 x 300 195 1 10712 x 310 205 1 10912 x 395 260 1 11013 x 310 205 1 11113 x 395 260 1 112

HSSd1 h8 x l1 l2 10621 …

mm mm MT14 x 325 220 1 11314 x 410 275 1 11415 x 340 220 2 11515 x 425 275 2 11616 x 355 230 2 11716 x 445 295 2 11817 x 355 230 2 11918 x 370 245 2 12118 x 465 310 2 122

HSSd1 h8 x l1 l2 10621 …

mm mm MT19 x 465 310 2 12420 x 385 260 2 12520 x 490 325 2 12622 x 515 345 2 13024 x 555 365 3 13425 x 440 290 3 13525 x 555 365 3 13628 x 580 385 3 14230 x 460 305 3 145

10621

Al<10%Si Al>10%Si Cu St<520N St<750N St<900N St<1100N St<1200N St<1400N <45HRC <55HRC <60HRC <67HRC VA-steel<900N VA-steel>900N Ti alloys GG(G) plastics50-60 40-50 25-30 25-28 20-24 15-18 - - - - - - - - - - 20-24 -

Al<10%Si Al>10%Si Cu St<520N St<750N St<900N St<1100N St<1200N St<1400N <45HRC <55HRC <60HRC <67HRC VA-steel<900N VA-steel>900N Ti alloys GG(G) plastics35-45 30-36 18-22 18-22 18-22 15-18 - - - - - - - - - - 14-20 -

HSS

HSS

DIN341

DIN1870

Reihe 1, 2

d1

l2l1


ß

www.hhw.de 10.29

1

eng/OP

Cutting

Spiralbohrer DIN 345 Typ N10510 Core Drill with Morse Taper Shank

TypeVery rounded heel, surface-treated for reducedtendency of the machined material to stick to themachining tool and improved chip removal.QualityHSS ground for standard-duty materials with astrength of up to 900 N/mm2.

Advantage: For core-drilling of non-circular holes,non-aligning boreholes can be evened out.

Note:The diameter to be core-drilled should be at least3/4 of the diameter of the core drill.

10632

HSSd1 h8 l2 l1 10632 …

mm mm mm MT7,80 75 156 1 1018,00 75 156 1 1028,80 81 162 1 1039,80 87 168 1 104

10,00 87 168 1 10510,75 94 175 1 10611,75 101 182 1 10712,00 101 182 1 10812,75 101 182 1 10913,75 108 189 1 11014,00 108 189 1 11114,75 114 212 2 11215,00 114 212 2 11315,75 120 218 2 114

HSSd1 h8 l2 l1 10632 …

mm mm mm MT16,00 120 218 2 11516,75 125 223 2 11617,00 125 223 2 11717,75 130 228 2 11818,00 130 228 2 11918,70 135 233 2 12019,70 140 238 2 12120,00 140 238 2 12220,70 145 243 2 12321,70 150 248 2 12422,00 150 248 2 12525,00 160 281 3 12730,00 175 296 3 129

10632

Al<10%Si Al>10%Si Cu St<520N St<750N St<900N St<1100N St<1200N St<1400N <45HRC <55HRC <60HRC <67HRC VA-steel<900N VA-steel>900N Ti alloys GG(G) plastics55-63 40-50 25-32 25-32 25-32 20-25 - - - - - - - - - - 20-28 16-25

HSSZ 3DIN343

d1

l2l1

www.atorn.de


A-Cut recessing systems by ATORN:

ATORN‘s high-quality turning tools.


• Multiplex-Holder

www.hhw.de10.30

1

eng/OP

Holder with Straight Shank 3 x D

T10649

For drilling l2 l1 D1 d2 B Torx screws 10649 …Ø D mm mm mm mm mm mm G

9,70-11,70 50 107 9,5 20 2,5 M2,0 x 4 20111,71-13,40 53 109 11,5 20 2,5 M2,0 x 4 20213,41-16,40 60 116 13,0 20 3,5 M2,5 x 5 20316,41-18,90 65 118 16,0 20 3,5 M2,5 x 7 20418,91-22,40 73 124 18,5 20 4,0 M3,0 x 6 20522,41-25,40 78 127 22,0 20 4,0 M3,0 x 7 20625,41-29,00 105 178 24,0 32 5,0 M3,5 x 10 20729,01-35,00 108 178 28,0 32 5,0 M3,5 x 10 20835,01-45,00 152 223 34,0 32 7,0 M4,0 x 15 20945,01-55,00 152 233 44,0 40 7,0 M4,0 x 15 21055,01-65,00 152 233 54,0 40 7,0 M4,0 x 15 211

10649


T10650



10650

. Do you know the Multiplex Drilling System made by T ?

Tooling system with internal coolant feedholders in different lengths and shank typesand exchangeable plates, therefore. no resharpening,. always original grind,. same constant length.

Each holder is drilling with inserts ofdifferent diameters and cutting materialssuch as coated HSS-E PM and solidcarbide – always in accordance to thematerial to be machined.Drilling range from Ø 9,8 up to 102 mm – often up to 7 x d.Not suitable for core-drilling pre-cast or pre-drilled holes. For all the things which you

have up to now drilled with conventionaldrills, you can now use the MULTIPLEXDRILLING SYSTEM. quicker,. more accurate,. higher quality,. lower price.

The MULTIPLEX Drilling System offersmany advantages:. no costs for re-sharpening,. the coating advantage fully remains,. high chip removal capacity and optimum

service life thanks to internal cooling. constant tool length. no time needed for pre-setting and

adjusting tools on NC-automatedmachines

. reduction of storage costs.

Optional use as a special tool for thefollowing working steps. drilling, . countersinking, . face cutting,. bevelling, . facing and boring,. counterboring.

The MULTIPLEX Drilling System helps toreduce your costs!

TTypeWith internal coolant feed. With straightshank, right-hand cut. Up to drilling Ø 35mm hardened and nickel-plated. Abovenickel-plated. Without cutting inserts.Point angle: up to Ø 25,4 = 135°, above Ø 25,4 = 132°.Web-thinned: Special shape with short chisel edge.

ApplicationFor drilling steel and cast steel, alloyed andunalloyed, with a strength of up toapprox. 1100N/mm2 , grey cast iron,malleable cast iron, spheroidal cast iron,sintered iron, German silver, bronze, brass.

. 10649 - 10672 Multiplex Exchangeable Blades-Twist Drills


ß

www.hhw.de 10.31

1

eng/OP

Cutting


T10651



10651

Holder with Morse Taper Shank10670 - 10671

Short holderFor drilling l2 l1 D1 B R Torx screws 10670 …

Ø D mm mm mm MT mm mm inch G25,00-29,00 108 279 4 24 5 G1/4 M3,5 x 10 10129,01-35,00 108 279 4 28 5 G1/4 M3,5 x 10 10235,01-45,00 152 324 4 34 7 G1/4 M4,0 x 15 10345,01-55,00 152 324 4 44 7 G1/4 M4,0 x 15 10455,01-65,00 152 324 4 54 7 G1/4 M4,0 x 15 105

10670

Long holderFor drilling l2 l1 D1 B R Torx screws 10671 …

Ø D mm mm mm MT mm mm inch G25,00-29,00 208 379 4 24 5 G1/4 M4,5 x 10 10129,01-35,00 208 379 4 28 5 G1/4 M4,5 x 10 10235,01-45,00 257 429 4 34 7 G1/4 M4,0 x 15 10345,01-55,00 257 429 4 44 7 G1/4 M4,0 x 15 10455,01-65,00 257 429 4 54 7 G1/4 M4,0 x 15 105

TTypeCoolant feed at the side of the morse taper shank.Up to a drill Ø of 35 mm hardened and nickel-plated,above that steam-treated.

10671

R"

l1

D

l2D1

R"

l1 D1D

l2

www.atorn.de


Short chucks by ATORN:

ATORN‘s high-quality clamping tools.


• Multiplex Exchangeable blades

www.hhw.de10.32

1

eng/OP

Exchangeable Blades for Multiplex System

TTypeWith surface grind, right-hand cut.

10654 QualityHSS-E/TiN for steel with a strength of up to 1200N/mm2, cast iron, aluminium. With chip dividergroove for short chips.

10655 QualityHSS-E/Fire-coating for increased service life insteel with a strength of up to 1200 N/mm2, cast

iron, aluminium, brass, bronze. With chip dividergroove for short chips.

10657 QualitySolid carbide//Fire-coating for a considerableincrease of service life and good performanceeven in steel with a hardness of up to 48 HRCand chilled cast iron. With land, without chipdivider groove.

10654 - 10657

10654

10655

10657

HSS-ETiN

HSS-EFIRE

H22FIRE


80-85 65-70 40-50 42-48 40-45 35-40 25-28 18-25 - - - - - 17-23 - - 33-40 -


80-85 65-70 40-45 35-40 30-35 25-30 22-25 - - - - - - 15-20 - - 28-35 -

10657Al<10%Si Al>10%Si Cu St<520N St<750N St<900N St<1100N St<1200N St<1400N <45HRC <55HRC <60HRC <67HRC VA-steel<900N VA-steel>900N Ti alloys GG(G) plastics140-160 130-150 70-80 90-100 80-85 75-80 70-75 55-65 40-45 30-35 - - - 30-45 - - 70-90 70-80

HSS-E/TiN HSS-E/Fire H 22/FireØ B 10654 … 10655 … 10657 …

mm mm10,00 2,5 602 602 60210,20 2,5 603 60310,50 2,5 604 60411,00 2,5 607 607 60711,75 2,5 61312,00 2,5 615 615 61512,50 2,5 621 621 62112,75 2,5 624 62413,00 2,5 625 625 62513,50 3,5 628 628 62813,75 3,5 629 62914,00 3,5 630 630 63014,25 3,5 631 63114,50 3,5 633 633 63314,75 3,5 634 63415,00 3,5 635 635 63515,25 3,5 63615,50 3,5 637 637 63715,75 3,5 638 63816,00 3,5 639 63916,25 3,5 64016,50 3,5 641 641 64117,00 3,5 643 643 64317,50 3,5 645 645 64517,75 3,5 646 64618,00 3,5 647 647 64718,25 3,5 648 648 64818,50 3,5 649 649 649

HSS-E/TiN HSS-E/Fire H 22/FireØ B 10654 … 10655 … 10657 …

mm mm18,75 3,5 650 65019,00 4,0 651 651 65119,50 4,0 654 654 65419,75 4,0 655 65520,00 4,0 656 656 65620,25 4,0 657 65720,50 4,0 658 658 65821,00 4,0 661 661 66121,25 4,0 66221,50 4,0 663 663 66321,75 4,0 664 66422,00 4,0 665 665 66522,50 4,0 668 66823,00 4,0 670 670 67023,50 4,0 672 67224,00 4,0 675 67524,25 4,0 67624,50 4,0 677 677 67724,75 4,0 67925,00 4,0 680 680 68026,00 5,0 68527,00 5,0 69028,00 5,0 69529,00 5,0 70030,00 5,0 70533,00 5,0 72034,00 5,0 72535,00 5,0 730

48


Multiple clamps by ATORN:

ATORN‘s high-quality clamping tools.


ß

www.hhw.de 10.33

1

eng/OP

Cutting

Exchangeable Blades for Multiplex System

TTypeWith surface grind, right-hand cut.

QualityPM/TiAlN for materials with a strength of up to1200 N/mm2.

10672

HSS-E-PM/TiAlNØ B 10672 …

mm mm25 5 600

25,5 5 60126 5 602

26,5 5 60327 5 60428 5 60529 5 606

29.5 5 60730 5 60831 5 60932 5 610


mm mm33 5 61134 5 61235 5 61336 7 61437 7 61538 7 61639 7 61740 7 61841 7 61942 7 62043 7 621


mm mm44 7 62245 7 62346 7 62447 7 62548 7 62649 7 62750 7 62851 7 62952 7 63053 7 63154 7 632


mm mm55 7 63356 7 63457 7 63558 7 63659 7 63760 7 63862 7 63964 7 64065 7 641

10672

Torx® Clamping Screws

TType Pack = 5 pcs.

Application For Multiplex twist drills with exchangeable blades cat.-no. 10649 cont.

10674

drilling range Torx 10674 …Type mm size

M 2,0 x 4 10 - 13 T 6 201M 2,5 x 5 > 13 - 16 T 7 202M 2,5 x 7 > 16 - 18 T 7 203M 3,0 x 6 > 18 - 22 T 9 204

drilling range Torx 10674 …Type mm size

M 3,0 x 8 > 22 - 25 T 9 205M 3,5 x 10 > 25 - 35 T 15 206M 4,0 x 15 > 35 - 65 T 20 207M 5,0 x 20 > 65 - 102 T 20 208

10674

Oil-Feed Rings

TApplicationFor twist drills with reversible cutting inserts cat.-no. 10670 - 10671.

10676

10676

For holder D D1 L G 10676 …with MT mm mm mm M inch

4 80 31,75 45 10 1/4 101

D1

D

M

G L

Oil-Feed Threads

TTypeTubular steel DIN 2391, with external thread on both ends.

ApplicationFor coolant-feed ring cat.-no. 10676 101.

10678

Nominal Ø Thread Ø Length G 10678 …mm mm inch

1/4 13,16 200 1/4 101

10678

Al<10%Si Al>10%Si Cu St<520N St<750N St<900N St<1100N St<1200N St<1400N <45HRC <55HRC <60HRC <67HRC VA-steel<900N VA-steel>900N Ti alloys GG(G) plastics75-80 65-75 60-65 50-55 45-50 40-45 35-40 30-35 25-30 - - - - 25-28 - - 40-50 -


Digital slide callipers by ATORN:

ATORN‘s high-quality measuring tools.


• Step drills

www.hhw.de10.34

1

eng/OP

Step Drills

TTypeCountersink angle 90°. With straight shank,relieved cone grind, web-thinned chisel edge andsurface treatment.

ApplicationFor manufacturing through-holes DIN EN 20273,screw head countersinking shape A medium DIN 74part 1. Screw head countersinking DIN 963 - 966.QualityHSS ground for steel with a strength of up to 900N/mm2, aluminium alloys, bronze, brass.

10850

for d2 x d1 l2 l1 l3 10850 …Thread mm mm mm mm

M 3 3,4 x 6,6 63 101 9 101M 4 4,5 x 9,0 81 125 11 102M 5 5,5 x 11,0 94 142 13 103M 6 6,6 x 13,0 101 151 15 105M 8 9,0 x 17,2 130 191 19 107

10850

Step Drills

TTypeCountersink angle 180°. Relieved cone grind,web-thinned chisel edge and surface treatment.ApplicationFor manufacturing through-holes and countersinkingDIN EN 20273, screw head countersinks shape H,J, and K. Medium type in compliance with DIN 74part 2. Cheese head screws in compliance with DIN84, DIN 912, DIN 6912, DIN 7513, DIN 7984.QualityHSS ground for steel with a strength of up to 900N/mm2, cast iron, aluminium alloys, brass, andbronze.

10861TypeWith straight shank.

10862TypeWith morse taper shank.

10861

Straight shank Morse taper shankfor d2 x d1 l2 l1 l3 shank 10861 … 10862 …

Thread mm mm mm mm MTM 3 3,4 x 6,0 57 93 9 – 101M 4 4,5 x 8,0 75 117 11 – 102M 5 5,5 x 10,0 87 133 13 – 103M 6 6,6 x 11,0 94 142 15 – 104M 8 9,0 x 15,0 114 169 19 – 105M 8 9,0 x 15,0 114 212 19 2 105

M 10 11,0 x 18,0 130 191 23 – 106M 10 11,0 x 18,0 130 228 23 2 106M 12 13,5 x 20,0 140 238 27 2 107M 16 17,5 x 26,0 165 286 35 3 109M 20 22,0 x 33,0 185 334 43 4 111

10862

l3

180°

d2

l2l1

d1

l3

180°

d2

l2l1

d1

10861 - 10862

HSS

HSS

Step Drills10840

TTypeCountersink angle 90°. With straight shank,relieved cone grind, web-thinned chisel edge andsurface treatment.

ApplicationFor threaded holes and countersinking in compli-ance with DIN 336 part 1 and free countersinking forthrough-holes in compliance with DIN EN 20273.QualityHSS ground for steel with a strength of up to 900N/mm2, aluminium alloys, bronze, brass.

10840

l3

90°

d2

l2l1

d1


M 3 2,5 x 3,4 39 70 8,8 101M 4 3,3 x 4,5 47 80 11,4 102M 5 4,2 x 5,5 57 93 13,6 103


M 6 5,0 x 6,6 63 101 16,5 104M 8 6,8 x 9,0 81 125 21,0 105

M 10 8,5 x 11,0 94 142 25,5 106

HSSDIN8378


DIN8374


DIN8376

DIN8377


ß

www.hhw.de 10.35

1

eng/OP

Cutting

Short Step Drills

TTypeWith straight shank, relieved cone grind, web-thinned chisel edge and surface treatment.Quality HSS ground for steel with a strength of up to 900N/mm2, cast iron, aluminium alloys, brass, andbronze.

10866TypeCountersink angle 90°. For tapping drill holes DIN336 part 1. Free countersinking for through-holesDIN EN 20273 medium.

10867TypeCountersink angle 90°. for through-holes DIN EN20273. Countersinking DIN 74 part 1 fine, counter-sunk screws DIN EN ISO 2009 and 2010.

10868 TypeCountersink angle 180°. for through-holes DIN EN20273. screw head countersinks shape H, J, K, part2 medium. Cheese head screws DIN EN ISO 4762,DIN EN ISO 1207, DIN 6912, DIN 7513, DIN 7984.

10866

HSS HSS HSSfor d2 x d1 l2 l1 l3 10866 … 10867 … 10868 …

thread mm mm mm mmM 3 2,5 x 3,4 20 52 8,8 101M 4 3,3 x 4,5 24 58 11,4 102M 5 4,2 x 5,5 28 66 13,6 103M 6 5,0 x 6,6 31 70 16,5 104M 8 6,8 x 9,0 40 84 21,0 105

M 10 8,5 x 11,0 47 95 25,5 106M 12 10,2 x 13,5 54 107 30,0 107M 3 3,2 x 6,0 28 66 9,0 101M 4 4,3 x 8,0 37 79 11,0 102M 5 5,3 x 10,0 43 89 13,0 103M 6 6,4 x 11,5 47 95 15 104M 8 8,4 x 15,0 56 111 19,0 105

M 10 10,5 x 19,0 64 127 23,0 106M 3 3,4 x 6,0 28 66 9,0 101M 4 4,5 x 8,0 37 79 11,0 102M 5 5,5 x 10,0 43 89 13,0 103M 6 6,6 x 11,0 47 95 15,0 104M 8 9,0 x 15,0 56 111 19,0 105

M 10 11,0 x 18,0 62 123 23,0 106

10867

10868

10866

10867

90°

d1

d2

l3

l2

l1

10868

180°

d2

l2

l1

l3

d1

10866 - 10868

Solid Carbide Short Step Drills

0TypeWith straight shank, right-hand cut. Diametertolerance h8.ApplicationFor thread core holes. For economically producingboreholes and countersinkings in one operation.QualitySolid carbide/TiAIN-coated.

10863TypeCountersink angle 90°.

10864TypeCountersink angle 180°.ApplicationFor through-holes.

10863 - 10864

90°for d1 x d2 l3 l2 l1 shank-Ø 10863 …

thread mm mm mm mm mmM 3 2,5 x 3,4 8,8 20 62 6,0 101M 4 3,3 x 4,5 11,4 24 66 6,0 102M 5 4,2 x 5,5 13,6 28 66 6,0 103M 6 5,0 x 6,6 16,5 34 79 8,0 104M 8 6,8 x 9,0 21,0 47 89 10,0 105

M 10 8,5 x 11,0 25,5 55 102 12,0 106M 12 10,2 x 13,5 30,0 60 107 14,0 107

180°for d1 x d2 l3 l2 l1 shank-Ø 10864 …

thread mm mm mm mm mmM 3 3,4 x 6,0 9 28 64 6,0 101M 4 4,5 x 8,0 11 37 79 8,0 102M 5 5,5 x 10,0 13 43 89 10,0 103M 6 6,6 x 11,0 15 55 102 12,0 104M 8 9,0 x 15,0 19 60 115 16,0 105

M 10 11,0 x 18,0 23 62 123 18,0 106

10863

10864

HSS


Al<10%Si Al>10%Si Cu St<520N St<750N St<900N St<1100N St<1200N St<1400N <45HRC <55HRC <60HRC <67HRC VA-steel<900N VA-steel>900N Ti alloys GG(G) plastics50-75 40-60 20-40 25-45 20-35 20-30 20-25 15-20 10-15 - - - - 10-15 10-15 2-8 20-30 10-30


• Centre drills

www.hhw.de10.36

1

eng/OP

Centre Drill

TypeShape A 60°. Double-ended, right-hand cut, spiral flutes, relieved.Point angle 118°, relieved cone grind. Plain-type centre holeswithout protective countersinking, with large contact face ofworkpiece, using lathe centre.ApplicationFor producing centre holes in compliance with DIN 332 whenmachining standard-duty materials such as steel, cast metal, non-ferrous and light metal. Suitable for particularly heavy workpiecesusing live lathe centres.

Note:Centre drill with Ø 0,50 and 0,80mm, single-ended.

10869HSS.

10870

0HSS.

10871

0HSS-E/TiN-coated.

10872

0HSS-E/TiCN-coated.

10869 - 10870

10871

10872HSS HSS HSS-E/TiN HSS-E/TiCNd1 h7 d2 l1 10869 … 10870 … 10871 … 10872 …mm mm mm a0,50 3,15 25,0 10 pcs. 101 2010,80 3,15 25,0 10 pcs. 102 102 2021,00 3,15 31,0 10 pcs. 103 103 203 203

L 1,00 4,00 120,0 - 1041,25 3,15 31,0 10 pcs. 105 105 205 2051,60 4,00 35,0 10 pcs. 106 106 206 206

L 1,60 5,00 120,0 - 1072,00 5,00 40,0 10 pcs. 108 108 208 208

L 2,00 6,00 120,0 - 1092,50 6,30 45,0 10 pcs. 110 110 210 210

L 2,50 8,00 120,0 - 1113,15 8,00 50,0 10 pcs. 112 112 212 212

L 3,15 10,00 120,0 - 1134,00 10,00 55,0 10 pcs. 114 114 214 214

L 4,00 10,0 120,0 - 1195,00 12,50 63,0 - 115 115 215 215

L 5,00 14,0 120,0 - 1206,30 16,00 71,0 - 116 116 2168,00 20,00 80,0 - 117 117

10,00 25,00 100,0 - 118 118

l1

d1

d2

10869 - 10872

HSS Centre Drill Set10881

0Type15-part. Shape A, 60°, short. Point angle 118°,countersink angle 60°, right-hand cut. Set contents:3 pcs. 1,6 x 4,0 mm, 3 pcs. 2,0 x 5,0 mm, 3 pcs. 2,5 x 6,3 mm,3 pcs. 3,15 x 8,0 mm, 2 pcs. 4,0 x 10,0 mm, 1 ea. 5,0 x 12,5 mm.

ApplicationFor centre holes without protective countersinking incompliance with DIN 333. QualityHSS.

HSS10881 …

101

10881

HSS

HSS-ETiN

Centre Drill, Left-hand Cut

0TypeShape A, 60°.Double-ended, left-hand cut, spiralflutes, relieved.Point angle 118°, relieved cone grind.

ApplicationFor left turning machine tools.QualityHSS.

10873

HSSd1 h7 d2 l1 10873 …mm mm mm a1,00 3,15 31,0 10 pcs. 1031,60 4,00 35,0 10 pcs. 1062,00 5,00 40,0 10 pcs. 1082,50 6,30 45,0 10 pcs. 110

HSSd1 h7 d2 l1 10873 …mm mm mm a3,15 8,00 50,0 10 pcs. 1124,00 10,00 55,0 10 pcs. 1145,00 12,50 63,0 – 115

l1

d1

d2

10873

DIN333A HSS

DIN333A HSS

HSS-ETiCN

DIN333A

10870






ß

www.hhw.de 10.37

1

eng/OP

Cutting

Centre Drill10874 - 10876

0TypeDouble-sided (Ø 0,50 and 0,80 single-ended), right-hand cut. Spiral flutes, relieved, point angle 118°,relieved cone grind.QualityHSS.

10874TypeShape A with bead, 60°.Centre holes without protective countersinking, withstep bead, which offers additional lubricant reser-voir.ApplicationSuitable for high-speed workpieces when usingdead lathe centres.

10875TypeForm R, 60°.Centre holes with radius combine annular contactface of workpiece at lathe centre with the benefits ofa protective countersinking.ApplicationParticularly suitable for workpieces subject todeformation stress during machining.

10876TypeShape B, 60/120°.Centre holes with cone-shaped protective counter-sinking, with large contact face of workpiece, usinglathe centre.ApplicationParticularly suitable for workpieces or tools, whichoften need to be clamped between lathe centres.QualityHSS.

10874

10875

10876

Shape A Shape Rd1 h7 d2 l1 10874 … 10875 …mm mm mm a0,50 3,15 25,0 10 pcs. 1010,80 3,15 25,0 10 pcs. 1021,00 3,15 31,0 10 pcs. 103 1031,25 3,15 31,0 10 pcs. 1051,60 4,00 35,0 10 pcs. 106 1062,00 5,00 40,0 10 pcs. 108 1082,50 6,30 45 10 pcs. 110 1103,15 8,00 50,0 10 pcs. 112 1124,00 10,00 55,0 10 pcs. 114 1145,00 12,50 63,0 – 115 1156,30 16,00 71,0 – 116 116

Solid Carbide Centre Drills

0TypeShape A, 60°. Plain-type centre holes withoutprotective countersinking, with large contact face ofworkpiece, using lathe centre.

ApplicationFor producing centre holes when machining heavy-duty materials, such as steel with high-strength,different cast irons and aluminium with high contentof silicium. Suitable for particularly heavy work-pieces using live lathe centres.QualitySolid Carbide K10/K20.

10880

K10/K20d1 h7 d2 l1 10880 …mm mm mm1,00 3,15 31,5 1031,25 3,15 31,5 1041,60 4,00 35,5 1052,00 5,00 40,0 1062,50 6,30 45,0 1073,15 8,00 50,0 1084,00 10,00 56,0 1095,00 12,50 63,0 110

l1

d1

d2

10880

DIN333 HSS

Shape Bd1 h7 d2 l1 10876 …

mm mm mm a1,60 6,30 45,0 10 St. 1032,00 8,00 50,0 10 St. 1042,50 10,00 55,0 10 St. 1053,15 11,20 62,0 10 St. 1064,00 14,00 69,0 10 St. 1075,00 18,00 77,0 – 1086,30 20,00 80,0 – 109

l1

d1

d260

°

120°

l1

d1

d2


R

B

DIN333A




• NC spot drills • Taper pin drills

www.hhw.de10.38

1

eng/OP

NC Spot Drills

0TypeWith straight shank, right-hand cut. Extremely shortflutes, without lands, relieved cone grind. Specialdrill with weak web.ApplicationFor drilling steel and cast steel, both alloyed andunalloyed, up to a strength of approx. 1000N/mm2, grey cast iron, malleable cast iron, spheroi-dal cast iron, sintered iron, German silver, graphite,short-chipping aluminium alloys, diecasting, ductilebrass. Particularly suitable for accurate spot andcountersink-drilling on NC- und CNC-drivenmachines, jig drilling machines etc.

Note:Not suitable for deep holes! TiN-coated NC spotdrills, with different point angle, extended version, or with MT shank, available on request.

10890-10891

HSS-E 120° HSS-E 90° HSS-E/TiCN 120° HSS-E/TiCN 90°d1 h6 l2 l1 10890 … 10891 … 10892 … 10893 …mm mm mm

3 12,0 46 201 201 201 2014 12,0 55 202 202 202 2025 14,0 62 203 203 203 2036 16,0 66 204 204 204 2048 21,0 79 205 205 205 205

10 25,0 89 206 206 206 20612 30,0 102 207 207 207 20716 37,5 115 208 208 208 20820 40,0 131 209 209 209 209

10892-10893

10890 - 10893

Long NC Spot Drills

Type Point angle 90°. With straight shank, right-handcut. Extremely short flutes, without lands, relievedcone grind. Application For drilling steel and cast steel, both alloyed andunalloyed, up to a strength of approx. 1000N/mm2, grey cast iron, malleable cast iron, spheroi-dal cast iron, sintered iron, German silver, graphite,short-chipping aluminium alloys, diecasting, ductilebrass.

Note: Not suitable for deep holes!

10882 Quality HSS-E.

10883 Quality HSS-E/TiCN-coated.

10882

HSS-E 90° HSS-E/TiCN 90°d1 h6 l2 l1 10882 … 10883 …

mm mm mm4 12 100 104 1046 20 140 106 1068 25 140 108 108

10 25 170 110 11012 30 170 112 11216 35 200 116 11620 40 200 120 120

10883

10882 - 10883

HSS-E

HSS-ETiCN

HSS-E

HSS-ETiCN

10890 + 10891Al<10%Si Al>10%Si Cu St<520N St<750N St<900N St<1100N St<1200N St<1400N <45HRC <55HRC <60HRC <67HRC VA-steel<900N VA-steel>900N Ti alloys GG(G) plastics

40-100 30-60 35-65 30-50 25-35 20-30 14-20 - - - - - - - - - 20-35 10-4010892 + 10893

Al<10%Si Al>10%Si Cu St<520N St<750N St<900N St<1100N St<1200N St<1400N <45HRC <55HRC <60HRC <67HRC VA-steel<900N VA-steel>900N Ti alloys GG(G) plastics50-125 40-65 45-80 38-63 30-45 25-30 20-25 - - - - - - 15-25 8-15 4-14 25-40 10-40


40-100 30-60 35-65 30-50 25-35 20-30 14-20 - - - - - - - - - 20-35 10-4010883

Al<10%Si Al>10%Si Cu St<520N St<750N St<900N St<1100N St<1200N St<1400N <45HRC <55HRC <60HRC <67HRC VA-steel<900N VA-steel>900N Ti alloys GG(G) plastics50-125 40-65 45-80 38-63 30-45 25-30 20-25 - - - - - - 15-25 8-15 4-14 25-40 10-40

10890 + 10892

10891 + 10893


ß

www.hhw.de 10.39

1

eng/OP

Cutting

d1

l2l1

d2

1:50

Solid Carbide NC Spot Drills

ßType With straight shank, right-hand cut. Extremely shortflutes, without lands. Surface grind. Special drill withweak web.Application Particularly suitable for accurate spot and counter-sink drilling on NC and CNC-driven machines, jigdrilling machines etc. For drilling grey cast iron,hardened cast iron, short-chipping malleable castiron, hardened steel, non-ferrous metal, plastics etc.

Quality Carbide grade K 10/K 20. 10894 101-106

142° 120° 90°d1 h8 l1 l2 10894 … 10894 … 10895 …

mm mm mm2 32 6 010 097 1073 32 8 011 098 1084 40 10 012 099 1095 50 13 013 100 1106 50 13 014 101 1118 60 23 015 102 112

10 70 24 016 103 11312 70 24 017 104 11416 75 29 019 105 11520 100 35 021 106 116

10894 - 10895

Solid Carbide NC Spot Drills

ßType With straight shank in compliance with DIN 6535HA, right-hand cut, spiral flutes. Application Spot drilling and countersinking with NC-machines,for cast iron, malleable cast iron, non-ferrous lightmetal, abrasive plastics. Quality Solid carbide finest grit/TiAlN-coated.

10901

142° 120° 90°d1 h6 l1 l2 10901 … 10902 … 10903 …mm mm mm

2 32 6 101 101 1013 32 8 102 102 1024 40 10 103 103 1035 50 13 104 104 1046 50 13 105 105 1058 60 23 106 106 106

10 70 24 107 107 10712 70 24 108 108 10816 75 29 110 110 11020 100 35 112 112 112

10902

10903

10901 - 10903

Taper Pin Drills

TypeTaper 1:50. Straight shank with drive tang in compliance withDIN 1809, right-hand cut. Point angle 118°,relieved cone grind.ApplicationFor drilling steel and cast steel, both alloy and

carbon up to a strength of approx. 1000 N/mm2,grey cast iron, malleable cast iron, etc. For drillingtaper holes for taper pins DIN 1 and DIN 7978 inone operation. (For finishing, use taper pin reamerscat.-no. 13430- 13432.)QualityHSS.

Note:The diameter d1 of the taper pin drill refers to thenominal diameter of the taper pin.

10899

10899

HSSd1 h9 l1 l2 d2 10899 …mm mm mm mm

4 112 68 5,00 1055 122 73 6,30 1066 160 105 8,00 1078 207 145 10,00 108

10 245 175 12,50 10912 290 210 16,00 110

HSS


DIN1898A


• Boring and Deburring Tool • Step drills

www.hhw.de10.40

1

eng/OP

TypeDiameter tolerance +/- 0,13 mm.ApplicationFor boring holes in sheeting with a thickness of 0,4 to 3,0 mm of almost all alloys, stain-less steel, grey cast iron, aluminium, brass, plastics and fibreglass. Quality HSS.

Note:Spare cooling lubricant stick see cat.-no. 10937 101.

. 10918 - 10928 Boring and Deburring Tools (Step Drills)

Boring and Deburring Tool Set

TypeConsists of 1 ea. boring and deburring tool MC1M/ MC 2M and MC 3M, with cooling lubricantstick, in metal box.QualityHSS.

Note:Spare cooling lubricant stick see cat.-no. 10937 101.

10918

HSSHole Ø 10918 …

mm4 - 30 101

10918

Step Drills (3 Cutting Blades)

Note:1) Especially for electricians, for use in electric handdrills. 2) For thread size PG.Size M1- M6 und PG24 without clamping shank.

10919

HSSNo. of cutting Hole diameter Shank for material 10919 …

Size cutting blades mm Ø mm thickness mmM1 3 5,5 / 8,5 / 11,5 / 14,5 / 17,5 / 20,5 / 23,5 / 26,5 / 29,5 / 32,5 / 35,5 – 3 101M2 3 6 / 9 / 12 / 15 / 18 / 21 / 24 / 27 / 30 / 33 / 36 – 3 102M4 3 7 / 10 / 13 / 16 / 19 / 22 / 25 / 28 / 31 / 34 / 37 – 3 104M5 3 7,5 / 10,5 / 13,5 / 16,5 / 19,5 / 22,5 / 25,5 / 28,5 / 31,5 / 34,5 / 37,5 – 3 105M6 3 8 / 11 / 14 / 17 / 20 / 23 / 26 / 29 / 32 / 35 / 38 – 3 106

PG21 1) 3 12,5 (PG7) / 15,2 (PG9) / 18,6 (PG11) / 20,4 (PG13,5) / 22,5 (PG16) / 25,8 / 28, 3 (PG21) / 30,5 12 3 140PG29 1) 3 12,5 (PG7) / 15,2 (PG9) / 18,6 (PG11) / 20,4 (PG13,5) / 22,5 (PG16) / 25,8 / 28, 3 (PG21) / 30,5 /

33,6 / 37,0 (PG29) – 3 141PGT 1) 2) 3 11,4 (PG7) / 14,0 (PG9) / 17,25 (PG11) / 19,0 (PG13,5) / 21,25 (PG16) / 24,5 /2 6,75 (PG21) 12 5 145

10919

HSS

HSS

Accessories for Step Drill cat.-no. 10919

10921Clamping stemApplicationShank for sizes M1- M6 and PG 29 (cat.-no. 10919101-106 and 10919 141).

10922Spare Centre Drills

10921 101-102

10921 103-104

10922

Clamping shank Centre drillcylindrical morse taper shank for 10921 … 10922 …

Ø mm size9,5 – - 101

12,5 – - 102– MT 1 - 103– MT 2 - 104- - PG 21 + PG 29 102- - PGT 103

10921 - 10922


ß

www.hhw.de 10.41

1

eng/OP

Cutting


HSSSize No. of cutting Hole diameter Shank for material 10924 …

cutting blades mm Ø mm thickness mmMC 1M 2 4 / 5 / 6 / 7 / 8 / 9 / 10 / 11 / 12 6 5 130MC 2M 2 10 / 11 / 12 / 13 / 14 / 15 / 16 / 17 / 18 / 19 / 20 9 4 131MC 3M 2 20 / 21 / 22 / 23 / 24 / 25 / 26 / 27 / 28 / 29 / 30 12 4 132MC 4M 2 4 / 6 / 8 / 10 / 12 6 10 133MC 5M 2 6 / 8 / 10 / 12 / 14 / 16 / 18 / 20 / 22 / 24 10 5 134MC 7M 2 4 / 6 / 8 / 10 / 12 / 14 / 16 / 18 / 20 10 4 135

MC 10M 2 4 / 6 / 8 / 10 / 12 / 14 / 16 / 18 / 20 / 22 / 24 / 26 / 28 / 30 12 4 136

10924

Step Drills

ApplicationFor through-holes. Especially for boring holes insheeting, e.g. -Greenlee-

10926

HSSHole diameter Shank up to material 10926 …

Size mm/inch Ø mm thickness mmMC 521M 5 mm / 7 mm / 3/8 inch / 7/16 inch / 13 mm / 15 mm / 3/4 inch / 21 mm 10 4 101

10926

10924

Step Drills

TypeWith 2 spiral flutes (DBGM), -Kantenbrecher-(DBGM) deburring zone, and ROTASTOP (DBGM)comfort shank. Both steps (6 mm for corehole and 3mm for through hole) on one tool.

Application For burr-free drilling and reaming of cable screwconnections in compliance with DIN EN 60423. Forworking on cable distribution boxes, installation andjunction boxes, clamping boxes, switch cabinets,switch and control units, housings.

10927 101

Thread Corehole (6 mm steps)Ø thread7 –10,5 M 12 x 1,514,5 M 16 x 1,518,5 M 20 x 1,523,5 M 25 x 1,530,5 M 30 x 1,5

Through hole (3 mm steps)Ø thread12,5 M 12 x 1,516,5 M 16 x 1,520,5 M 20 x 1,525,5 M 25 x 1,532,5 M 30 x 1,5

HSS10927 …

QualityHSS 101

TiN-coated 201TiAlN-coated 301

10927 201

10927 301

10927

HSS

HSS

HSS

HSS-ETiAIN


TypeWith straight shank. Boring steps exactly in 1 mmincrements.

ApplicationFor drilling straight holes up to 4 mm materialthickness of almost all materials such as steel, castmetal, brass, plastics and fibreglass. No pre-drillingnecessary.

10928

HSSSize No. of cutting Hole diameter Shank for material 10928 …

cutting blades mm Ø mm thickness mmTMC3040 6 30 / 31 / 32 / 33 / 34 / 35 / 36 / 37 / 38 / 39 / 40 13 4 101TMC4050 6 40 / 41 / 42 / 43 / 44 / 45 / 46 / 47 / 48 / 49 / 50 13 4 102TMC5060 6 50 / 51 / 52 / 53 / 54 / 55 / 56 / 57 / 58 / 59 / 60 13 4 103

10928 HSS


• Slabbing Cut Drill Reamer • Milling cutters • Spot-Weld Milling Cutters • Core drills

www.hhw.de10.42

1

eng/OP

Slabbing Cut Drill Reamer (Sheet Metal Drills) Sets

ßTypeWith straight shank. Drilling range 3 - 30,5mm,consists of 1 each drill size 1, 2, and 3, in plasticbox.ApplicationFor drilling and reaming holes in thin material free ofburrs and chatter marks in one operation. Forannealed sheet steel, stainless sheet steel, car-bodysheeting, non-ferrous metals, thin-walled pipes andplastics such as PVC, plexiglas, Resopal etc., alsofor hardboard, plywood etc.

Note:For drilling up to the edge without deformation.Cooling lubricant stick see cat.-no. 10937 101.

10934201QualityHSS-E.

10934202QualityHSS-E/TiN-coated.

10934 201

Quality 10934 …

HSS-E 201HSS-E/TiN 202

10934 202

10934

Slabbing Cut Drill Reamers (Sheet Metal Drills)

ßTypeWith straight shank.ApplicationFor drilling and reaming holes in thin material free ofburrs and chatter marks in one operation. Forannealed sheet steel, stainless sheet steel, car-bodysheeting, non-ferrous metals, thin-walled pipes andplastics such as PVC, plexiglas, Resopal etc., alsofor hardboard, plywood etc.

Note:Cooling lubricant necessary!

10935QualityHSS-E.

10936QualityHSS-E/TiN-coated.

10937Cooling lubricantTypeWithout silicone, contents 25 ml.ApplicationFor lubricating all contact faces during drilling andthread cutting.

10935

HSS-E HSS-E/TiN Cooling lubricant stickSize for hole Ø Shank 10935 … 10936 … 10937 …

mm Ø mm1 3 - 14,0 6 101 1012 8 - 20,0 8 102 1023 16 - 30,5 9 103 1034 26 - 40,0 12 104 1045 36 - 50,0 12 105 1056 46 - 60,0 12 106 1067 4 - 30,5 9 107 107– – – 101

10937

10935 - 10937

10936

HSS-EHSS-E

TiN

HSS-E

HSS-ETiN

Universal Drill/Milling Cutter

ßTypeWith straight shank.ApplicationFor drilling and cutting out any contour required inall kinds of metal sheeting; also suitable for wood,Resopal and other plastics.QualityHSS.

Note:Best speed approx. 1000- 1200 1/min. For materialwhich bind (zinc, aluminium etc.), occasionally dipthe tool into a lubricant. For use in power hand drills.Cooling lubricant stick see cat.-no. 10937 101.

10940

10940

HSSØ 10940 …

mm6,35 101

HSS


ß

www.hhw.de 10.43

1

eng/OP

Cutting

Spot-Weld Milling Cutters

TypeThe milling head is reversible, the milling depth canbe adjusted.ApplicationFor loosening spot-welded sheeting without defor-mation or tear. For sheet metal processing, car bodyworkshops, industry etc.QualityHSS.

Note:Best speed approx. 900 1/min.

10942

HSSMilling head 10942 …

Ø mmMilling cutter 10 101

Spare milling head 10 102

10942

HSS-Co Core Drills (Weldon)

TypeThe core drill is cutting only a small groove, theremaining core part is ejected in uncut condition,low driving performance - up to 4 times less drillingtime, high service life - low wear. All core drills withWeldon shank 19 mm for direct mounting or MTmounting AMT-3 with internal cooling system.ApplicationSuitable for magnetic core drilling machine (cat.-no.90060) or table and column drilling machines.QualityHSS-Co.

Note:Carbide-tipped core drills or drills with other cuttingdepths available on request.

10955 Cutting depth 25 mm.

10956 Cutting depth 50 mm.

25 mm 50 mmØ 10955 … 10956 …

mm12 101 10113 102 10214 103 10315 104 10416 105 10517 106 10618 107 10719 108 10820 109 10921 110 11022 111 11123 112 11224 113 113

25 mm 50 mmØ 10955 … 10956 …

mm25 114 11426 115 11527 116 11628 117 11729 118 11830 119 11931 120 12032 121 12133 122 12234 123 12335 124 12436 125 12537 126 126

25 mm 50 mmØ 10955 … 10956 …

mm38 127 12739 128 12840 129 12941 130 13042 131 13143 132 13244 133 13345 134 13446 135 13547 136 13648 137 13749 138 13850 139 139

10955

10955 - 10956

HSS

Accessories for Core Drills

10957Clamping shank MT-3TypeMT 3, with automatic internal coolant feed andgrease nipples for coolant tube. In plastic case.ApplicationFor mounting HSS-Co core drills (cat.-no.10955-10956). For magnetic core drilling machine cat.-no. 90060 203.

10958Spare ejector pinsApplicationFor HSS-Co core drills from Ø 12 up to 50 mm.

10957

MT-3 ejector pinfor cutting depth for Ø 10957 … 10958 …

Size mm mmMT 3 – – 102

– 25 12 099– 25 13-50 101– 50 13-50 102– 50 12 103

10958

10957 - 10958


• Core drills

www.hhw.de10.44

1

eng/OP

HSS Carbide qualityHole Ø Total 10959 … 10959 …

mm length mm12 77 101 20113 77 102 20214 77 103 20315 77 104 20416 77 105 20517 77 106 20618 77 107 20719 77 108 20820 77 109 20921 77 110 21022 77 111 21123 77 112 21224 77 113 21325 77 114 21426 77 115 21527 77 116 21628 77 117 21729 77 118 218


mm length mm30 77 119 21931 77 120 22032 77 121 22133 77 22234 77 22335 77 22436 77 22537 77 22638 77 22739 77 22840 77 22941 77 23042 77 23143 77 23244 77 23345 77 23446 77 23547 77 236


mm length mm48 77 23749 77 23850 77 23951 77 24052 77 24153 77 24254 77 24355 77 24456 77 24557 77 24658 77 24759 77 24860 77 24961 77 25062 77 25163 77 25264 77 25365 77 254

QuickIN Core Drills

YType With QuickIN mount.The core drill is cutting only asmall groove, the remaining core part is ejected inuncut condition, lower driving performance - up to 4times less drilling time, high service life - less wear. Application For a cutting depth of up to 35 mm. For directmounting in core drilling machines KBM 65 Q/65QF (cat.-no. 90057), for KBM 65/65 F (predecessor)by means of QuickIN clamping shank (cat.-no.10962) and for table and column drilling ma-chines by means of QuickIN clamping shank (cat.-no. 10964).

Note: Core drills with other diameters and cutting depthsavailable on request.

10959 090 Core Drill Sets 7-part, in plastic carrying case, incl. of 1 centring pin. HSS.

10959 191Core Drill Sets 5-part, in plastic carrying case, incl. of 1 centring pin. Carbide.

10959 101-121 Core drill, single. HSS.

10959 201-254Core drill, single. Carbide.

10959 090

HSSSet Corehole 10959 …

Contents Ø mm7-part 14 / 16 / 18 / 20 / 22 / 26 0905-part 14 / 18 / 22 / 32 191

10959 191

10959 201-25410959 101-121

10959

Core Drills (with Thread)

YType With thread M 18 x 6 P 1,5. The core drill is cuttingonly a small groove, the remaining core part isejected in uncut condition, lower driving perform-ance - up to 4 times less drilling time, high servicelife - less wear.

Application For a cutting depth of up to 50 mm. For directmounting in core drilling machines KBM 65/65 F(predecessor), for KBM 65 Q/65 QF (cat.-no. 90057)by means of QuickIN clamping shank (cat.-no.10962) and adapter (cat.-no. 10965) and for tableand column drilling machines by means ofQuickIN clamping shank (cat.-no. 10964) andadapter (cat.-no. 10965).Quality Carbide.

Note: Core drills with other cutting depths available onrequest.

Hole Ø Total 10960 …mm length mm

12 82 60113 82 60214 82 60315 82 60416 82 60517 82 60618 82 60719 82 60820 82 60921 82 61022 82 61123 82 612

Hole Ø Overall 10960 …mm length mm

24 82 61325 82 61426 78 61527 78 61628 78 61729 78 61830 78 61931 78 62032 78 62133 78 62234 78 62335 78 624

Hole Ø Overall 10960 …mm length mm

36 78 62537 78 62638 78 62739 78 62840 78 62941 78 63042 78 63143 78 63244 78 63345 78 63446 78 63547 78 636

Hole Ø Total 10960 …mm length mm

48 78 63749 78 63850 78 63952 78 64154 78 64356 78 64558 78 64760 78 64965 78 654

10960

HSS HM

10960


ß

www.hhw.de 10.45

1

eng/OP

Cutting

QuickIN Clamping Shank (Core Drilling Machines)

YType With morse taper shank MT 3 and integrated coolinglubricant feed.

Application For core drilling machines KBM 65/65 F (earliermodel) and KBM 65 Q/65 QF (cat.-no.90057) Fordirect mounting of QuickIN core drills (cat.-no.10959) or by means of adapter (cat.-no. 10965) ofcore drills with thread (cat.-no. 10959) and/or withWeldon shank (cat.-no. 10955).

10962

for core drills 10962 …shank Hole Ø mm

MT 3 12 - 65 101

10962

QuickIN Clamping Shanks (Table and Column Drilling Machines)

YType With morse taper shank and pump for externalcooling lubricant feed.

Application For table and column drilling machines. Fordirect mounting of QuickIN core drills (cat.-no.10959) or by means of adapter (cat.-no. 10965) ofcore drills with thread (cat.-no. 10960) and/or withWeldon shank (cat.-no. 10955).

10964

for core drills 10964 …shank Hole Ø mm

MT 2 12 - 65 101MT 3 12 - 65 102

10964

QuickIN Adapters

YApplication For core drilling machines KBM 65/65 F (prede-cessor), KBM 65 Q/65 QF (cat.-no. 90057) andtable and column drilling machines.

10965 101 Type Output M 18 x 6 P 1,5. Application For mounting core drills with thread (cat.-no.10960).

10965 102 Type Output Weldon. Application For mounting core drills with Weldon shank (cat.-no.10955).

10965 101

10965 …Output

M 18 x 6 P 1,5 101Weldon 102

10965 102

10965

Centring Pins

YApplication For the ejection of the uncut remaining core part.

10966 101 Application For core drills with QuickIN mount (cat.-no.10955)

10966 102 Application For core drills with thread (cat.-no. 10960).

10966

for core drill Length 10966 …with mount mm

QuickIN 105 101thread 125 102

10966


Twist drills 10 - p-alians.ru · • Twist drills • Miniature drills ... HHW Grundlayout 2008...

Documents

Transcript of Twist drills 10 - p-alians.ru · • Twist drills • Miniature drills ... HHW Grundlayout 2008...