Tutorial Autopipe 05
-
Upload
lisa-norman -
Category
Documents
-
view
343 -
download
15
Transcript of Tutorial Autopipe 05
-
8/10/2019 Tutorial Autopipe 05
1/22
Support
Beberapa Support /Penyangga Pipa antara lain : V-Stop Inclined Line Stop Guide Rotation Damper Tie / Link
SUPPORT : Berfungsi untuk menopong/menyangga bentangan pipa untuk menambah kemampuan pipa menerima beban gaya, termal dan pengaruhlingkungan seperti gempa. Perbedaan beban dan operasional kerja pipamaka pemilihan support harus tepat.
-
8/10/2019 Tutorial Autopipe 05
2/22
Diagram Support
-
8/10/2019 Tutorial Autopipe 05
3/22
Support
-
8/10/2019 Tutorial Autopipe 05
4/22
Saddle Support V-Stop : hanya di rancang untuk menahan beban vertikal contoh
Saddle Support
-
8/10/2019 Tutorial Autopipe 05
5/22
Saddle Support
-
8/10/2019 Tutorial Autopipe 05
6/22
Trunnion SupportInclined : Any support whose bearing restraint direction is skewed.
Examples include: wires, sway braces, and struts.
-
8/10/2019 Tutorial Autopipe 05
7/22
Trunnion Support
-
8/10/2019 Tutorial Autopipe 05
8/22
Rod Support
Support yang digunakan adalah incline
Terdapat 2 rod/batangDengan spring rate :913.000 lb/in
Cara :Insert/Support Inclined
di A01 dimana direction bearing x dan y nilai 1
Insert/Support Inclineddi A01 dimana direction bearing x =-1 dan y = 1
-
8/10/2019 Tutorial Autopipe 05
9/22
Pedestal with Rigid Strap
-
8/10/2019 Tutorial Autopipe 05
10/22
Rigidly Guided Pipe Slide Assembly
-
8/10/2019 Tutorial Autopipe 05
11/22
Lateral Tees
-
8/10/2019 Tutorial Autopipe 05
12/22
Modeling Valve Operators
-
8/10/2019 Tutorial Autopipe 05
13/22
Operator eccentricity in a seismic
load case-Dia pipa 12 inch- Insert/Valve-
-
8/10/2019 Tutorial Autopipe 05
14/22
Operator eccentricity in a seismic
load case
Selanjutnya :
di ulangi lagiuntuk point A02ke A03
-
8/10/2019 Tutorial Autopipe 05
15/22
Selanjutnya :
Sorot point A02
Dan lakukanInsert/XtraData/Additional Weight
-
8/10/2019 Tutorial Autopipe 05
16/22
-
8/10/2019 Tutorial Autopipe 05
17/22
Operator eccentricity in a
response spectrum load caseInsert/Frame
Rigid beam (M1)Dari A02 ke titikCGO (center of gravity0f the operator)lokasi CGO 1.25 ftdiatas A02.
-
8/10/2019 Tutorial Autopipe 05
18/22
-
8/10/2019 Tutorial Autopipe 05
19/22
Diameter Pipa : 8
Setelah ValveMasukan ;
A05 run arah DX 6
-
8/10/2019 Tutorial Autopipe 05
20/22
Insert/Nozzle
-
8/10/2019 Tutorial Autopipe 05
21/22
Insert/Segment : offset A06 Dengan Nama Segment Baru ; B00Nama Pipa : VESLDiameter : NS (non standart) 144 dan tebal 2
Insert/Anchor : pada B00Nama Pipa : Lanjutkan dengan RUN component pada tabeldi b awah ini
Pergeseran Point B01 ke Point A06
Dengan cara memasukan nilai 0 Global Y pada B00 di tabelProperty
Menyambung Point A06 dengan B01 dengan perintah RUN daripoint A06 dan name of point diganti B01 selanjutnya akankeluar dialog Tee, default WELDING diganti OTHER denganSIF = 1.0
-
8/10/2019 Tutorial Autopipe 05
22/22
Pilih : Insert/Rigid Option Over Range NAMUN sebelumnya componen A06Dan B01 benar-benar terpilih (gunakan SOLID MODEL VIEW) untukmemudahkan memilih.