TURBINE PUMP CURVE - Pump Solutions #1 Corp
26
° 8JS 1760 RPM JANUARY 2010 TURBINE PUMP CURVE IMPELLER DATA PUMP MATERIAL EFFICIENCY CORRECTION FLANGED BOWL DATA IMPELLER NUMBER 3692 TYPE SEMI-OPEN THRUST FACTOR K=3.52 EYE AREA 3.18 SQ. IN. WEIGHT 3.55 LB. Minimum submergence above eye of bottom impeller: 14 IN. Performance based on pumping clear, fresh water at a temperature not over 85 F., free of gas, air or abrasives and with bowls properly adjusted and submerged. Performance curve reflects Hydraulic Institute tolerances and guidelines. IMPELLER MATERIAL: BOWL MATERIAL: BRONZE BOWL NUMBER 3629 BOWL MAX. DIAMETER 7.813 IN. BOWL MIN. DIAMETER 7.500 IN. MAX. NO. STAGES 42 ONE STAGE WEIGHT 130 LB. ADD STAGE WEIGHT 30 LB. STD. SHAFT DIA. 1.000 IN. STD. LATERAL 0.438 IN. DISCHARGE SIZE 5 - 6 IN. DISCHARGE CONNECTION THD - FLG SUCTION SIZE 5 - 6 IN. SUCTION CONNECTION THD MAX. SPHERE SIZE 0.250 IN. MAX. OPERATIONAL P.S.I. 692 (SPECIAL) EFFICIENCY CORRECTION NUMBER OF BOWLS: CHANGE AS FOLLOWS: CHANGE IN EFFICIENCY MAY AFFECT BOTH HEAD AND HORSEPOWER. 1 2 3 -3 -1 0 NI-R STAINLESS DUCTILE SINGLE STAGE PERFORMANCE 480 SERIES US gpm Power - hp 130 120 110 100 90 80 70 60 50 40 30 20 0 10 0.5 1 NPSHr - ft 130 120 110 100 90 80 70 60 50 40 30 0 20 2.5 10 5 Head - ft 130 120 110 100 90 80 70 15 60 20 50 40 25 30 30 20 35 10 6.313 in 6.313 in 6 in 5.625 in 65 65 65 65 70 70 70 70 74 74 74 74 76 76 76 76 78 78 -2 0 -1 -2 -2 -2 -2 -5
Transcript of TURBINE PUMP CURVE - Pump Solutions #1 Corp
°
8JS 1760 RPM
JANUARY 2010
TURBINE PUMP CURVE
IMPELLER DATA
PUMP MATERIAL EFFICIENCY CORRECTION
FLANGED BOWL DATAIMPELLER NUMBER 3692TYPE SEMI-OPENTHRUST FACTOR K=3.52EYE AREA 3.18 SQ. IN.WEIGHT 3.55 LB.
Minimum submergence aboveeye of bottom impeller: 14 IN.
Performance based on pumping clear, fresh water at a temperature not over 85 F., free of gas, air or abrasives and with bowls properlyadjusted and submerged. Performance curve reflects Hydraulic Institute tolerances and guidelines.
IMPELLER MATERIAL:BOWL MATERIAL:
BRONZE
BOWL NUMBER 3629BOWL MAX. DIAMETER 7.813 IN.BOWL MIN. DIAMETER 7.500 IN.MAX. NO. STAGES 42ONE STAGE WEIGHT 130 LB.ADD STAGE WEIGHT 30 LB.STD. SHAFT DIA. 1.000 IN.STD. LATERAL 0.438 IN.DISCHARGE SIZE 5 - 6 IN.DISCHARGE CONNECTION THD - FLGSUCTION SIZE 5 - 6 IN.SUCTION CONNECTION THDMAX. SPHERE SIZE 0.250 IN.MAX. OPERATIONAL P.S.I. 692 (SPECIAL)
EFFICIENCY CORRECTIONNUMBER OF BOWLS:CHANGE AS FOLLOWS:
CHANGE IN EFFICIENCY MAY AFFECT BOTH HEAD AND HORSEPOWER.
1 2 3
-3 -1 0
NI-R STAINLESSDUCTILE
SINGLE STAGE PERFORMANCE
480 SERIES
US gpm
Pow
er -
hp
13012011010090807060504030200 10
0.5
1
NPSH
r - ft
130120110100908070605040300 20
2.5
10
5
Head
- ft
130120110100908070
15
60
20
5040
25
30
30
20
35
10
6.313 in6.313 in
6 in
5.625 in
65
65
65
65
70
70
70
70
74
74
74
74
76
76 76
76
78
78
-2 0 -1 -2
-2 -2 -2 -5
°
8LS 1760 RPM
JANUARY 2010
TURBINE PUMP CURVE
IMPELLER DATA
PUMP MATERIAL EFFICIENCY CORRECTION
FLANGED BOWL DATAIMPELLER NUMBER 3641TYPE SEMI-OPENTHRUST FACTOR K=3.34EYE AREA 4.64 SQ. IN.WEIGHT 4.25 LB.
Minimum submergence aboveeye of bottom impeller: 14IN.
Performance based on pumping clear, fresh water at a temperature not over 85 F., free of gas, air or abrasives and with bowls properlyadjusted and submerged. Performance curve reflects Hydraulic Institute tolerances and guidelines.
IMPELLER MATERIAL:BOWL MATERIAL:
BRONZE
BOWL NUMBER 3629BOWL MAX. DIAMETER 7.813 IN.BOWL MIN. DIAMETER 7.500 IN.MAX. NO. STAGES 37ONE STAGE WEIGHT 130 LB.ADD STAGE WEIGHT 30 LB.STD. SHAFT DIA. 1.000 IN.STD. LATERAL 0.438 IN.DISCHARGE SIZE 5 - 6 IN.DISCHARGE CONNECTION THD - FLGSUCTION SIZE 5 - 6 IN.SUCTION CONNECTION THDMAX. SPHERE SIZE 0.250 IN.MAX. OPERATIONAL P.S.I. 692 (SPECIAL)
EFFICIENCY CORRECTIONNUMBER OF BOWLS:CHANGE AS FOLLOWS:
CHANGE IN EFFICIENCY MAY AFFECT BOTH HEAD AND HORSEPOWER.
1 2 3
-4 -2 0
NI-R STAINLESSDUCTILE
SINGLE STAGE PERFORMANCE
480 SERIES
US gpm
Pow
er -
hp
20017515012510075500 25
1
2
NPSH
r - ft
20017515012510075500 25
5
Head
- ft
20017515012515 100
20
75
25
50
30
35
25
40 6.313 in6.313 in
6 in
5.625 in
65
65
65
65
70
70
70
70
73
73
73
73
75
75
-2 0 -1 -2
-2 -2 -2 -5
°
8KS 1760 RPM
JANUARY 2010
TURBINE PUMP CURVE
IMPELLER DATA
PUMP MATERIAL EFFICIENCY CORRECTION
FLANGED BOWL DATAIMPELLER NUMBER 3693TYPE SEMI-OPENTHRUST FACTOR K=4.42EYE AREA 6.60 SQ. IN.WEIGHT 3.75 LB.
Minimum submergence aboveeye of bottom impeller: 20 IN.
Performance based on pumping clear, fresh water at a temperature not over 85 F., free of gas, air or abrasives and with bowls properlyadjusted and submerged. Performance curve reflects Hydraulic Institute tolerances and guidelines.
IMPELLER MATERIAL:BOWL MATERIAL:
BRONZE
BOWL NUMBER 3591BOWL MAX. DIAMETER 7.938 IN.BOWL MIN. DIAMETER 7.500 IN.MAX. NO. STAGES 37ONE STAGE WEIGHT 130 LB.ADD STAGE WEIGHT 30 LB.STD. SHAFT DIA. 1.000 IN.STD. LATERAL 0.438 IN.DISCHARGE SIZE 5 - 6 IN.DISCHARGE CONNECTION THD - FLGSUCTION SIZE 5 - 6 IN.SUCTION CONNECTION THDMAX. SPHERE SIZE 0.375 IN.MAX. OPERATIONAL P.S.I. 692 (SPECIAL)
EFFICIENCY CORRECTIONNUMBER OF BOWLS:CHANGE AS FOLLOWS:
CHANGE IN EFFICIENCY MAY AFFECT BOTH HEAD AND HORSEPOWER.
1 2 3
-3 -1 0
NI-R STAINLESSDUCTILE
SINGLE STAGE PERFORMANCE
480 SERIES
US gpm
Pow
er -
hp
300250200150100500
1
2
NPSH
r - ft
300250200150100500
10
20
Head
- ft
300250200150
10
100
20
50
30
6.313 in6.313 in
6 in
5.5 in
60
60
65
65
65
65
70
70
70
70
72
72
72
72
74
74
74
74
76
7676
7678
78
80
80
81
-2 0 -1 -2
-2 -2 -2 -5
°
8MS 1760 RPM
JANUARY 2010
TURBINE PUMP CURVE
IMPELLER DATA
PUMP MATERIAL EFFICIENCY CORRECTION
FLANGED BOWL DATAIMPELLER NUMBER 3590TYPE SEMI-OPENTHRUST FACTOR K=4.28EYE AREA 6.60 SQ. IN.WEIGHT 4.125 LB.
Minimum submergence aboveeye of bottom impeller: 24 IN.
Performance based on pumping clear, fresh water at a temperature not over 85 F., free of gas, air or abrasives and with bowls properlyadjusted and submerged. Performance curve reflects Hydraulic Institute tolerances and guidelines.
IMPELLER MATERIAL:BOWL MATERIAL:
BRONZE
BOWL NUMBER 3591BOWL MAX. DIAMETER 7.938 IN.BOWL MIN. DIAMETER 7.500 IN.MAX. NO. STAGES 23ONE STAGE WEIGHT 130 LB.ADD STAGE WEIGHT 30 LB.STD. SHAFT DIA. 1.000 IN.STD. LATERAL 0.438 IN.DISCHARGE SIZE 5 - 6 IN.DISCHARGE CONNECTION THD - FLGSUCTION SIZE 5 - 6 IN.SUCTION CONNECTION THDMAX. SPHERE SIZE 0.375 IN.MAX. OPERATIONAL P.S.I. 692 (SPECIAL)
EFFICIENCY CORRECTIONNUMBER OF BOWLS:CHANGE AS FOLLOWS:
CHANGE IN EFFICIENCY MAY AFFECT BOTH HEAD AND HORSEPOWER.
1 2 3 4 5
-4 -3 -2 -1 0
NI-R STAINLESSDUCTILE
SINGLE STAGE PERFORMANCE
480 SERIES
US gpm
Pow
er -
hp
4003503002502001501000 50
1
2
3
NPSH
r - ft
4003503002502001501000 50
10
20
Head
- ft
400350300250200
10
150
20
100
30
50
6.313 in6.313 in
6 in
5.5 in
65
65
65
65
70
70
70
70
72
72 72
72
74
7474
74
76
76
76
76
78
78
79
79
-2 0 -1 -2
-2 -2 -2 -5
°
8EHS 1760 RPM
JANUARY 2010
TURBINE PUMP CURVE
IMPELLER DATA
PUMP MATERIAL EFFICIENCY CORRECTION
FLANGED BOWL DATAIMPELLER NUMBER 2981TYPE SEMI-OPENTHRUST FACTOR K=5.40EYE AREA 8.48 SQ. IN.WEIGHT 3.25 LB.
Minimum submergence aboveeye of bottom impeller: 24 IN.
Performance based on pumping clear, fresh water at a temperature not over 85 F., free of gas, air or abrasives and with bowls properlyadjusted and submerged. Performance curve reflects Hydraulic Institute tolerances and guidelines.
IMPELLER MATERIAL:BOWL MATERIAL:
BRONZE
BOWL NUMBER 2883BOWL MAX. DIAMETER 7.938 IN.BOWL MIN. DIAMETER 7.500 IN.MAX. NO. STAGES 19ONE STAGE WEIGHT 130 LB.ADD STAGE WEIGHT 30 LB.STD. SHAFT DIA. 1.188 IN.STD. LATERAL 0.375 IN.DISCHARGE SIZE 5 - 6 IN.DISCHARGE CONNECTION THDSUCTION SIZE 5 - 6 IN.SUCTION CONNECTION THDMAX. SPHERE SIZE 0.625 IN.MAX. OPERATIONAL P.S.I. 692 (SPECIAL)
EFFICIENCY CORRECTIONNUMBER OF BOWLS:CHANGE AS FOLLOWS:
CHANGE IN EFFICIENCY MAY AFFECT BOTH HEAD AND HORSEPOWER.
1 2 3 4
-3 -2 -1 0
NI-R STAINLESSDUCTILE
SINGLE STAGE PERFORMANCE
480 SERIES
US gpm
Pow
er -
hp
4003503002502001501000 50
10
NPSH
r - ft
4003503002502001501000 50
10
20
Head
- ft
400350300250200
75
150
100
100
125
50
150 6.313 in6.313 in
6 in
5.625 in
64
64
64
64
69
69
69
69
72
72
72
72
74
74
-2 0 -1 -2
-2 -2 -2 -5
°
8YS 1760 RPM
JANUARY 2010
TURBINE PUMP CURVE
IMPELLER DATA
PUMP MATERIAL EFFICIENCY CORRECTION
FLANGED BOWL DATAIMPELLER NUMBER 5506TYPE SEMI-OPENTHRUST FACTOR K=8.00EYE AREA 15.9 SQ. IN.WEIGHT 5.00 LB.
Minimum submergence aboveeye of bottom impeller: 30 IN.
Performance based on pumping clear, fresh water at a temperature not over 85 F., free of gas, air or abrasives and with bowls properlyadjusted and submerged. Performance curve reflects Hydraulic Institute tolerances and guidelines.
IMPELLER MATERIAL:BOWL MATERIAL:
BRONZE
BOWL NUMBER 5503BOWL MAX. DIAMETER 7.938 IN.BOWL MIN. DIAMETER 7.500 IN.MAX. NO. STAGES 32ONE STAGE WEIGHT 139 LB.ADD STAGE WEIGHT 39 LB.STD. SHAFT DIA. 1.188 IN.STD. LATERAL 0.375 IN.DISCHARGE SIZE 5 - 6 IN.DISCHARGE CONNECTION THD - FLGSUCTION SIZE 5 - 6 IN.SUCTION CONNECTION THDMAX. SPHERE SIZE 1.125 IN.MAX. OPERATIONAL P.S.I. 692 (SPECIAL)
EFFICIENCY CORRECTIONNUMBER OF BOWLS:CHANGE AS FOLLOWS:
CHANGE IN EFFICIENCY MAY AFFECT BOTH HEAD AND HORSEPOWER.
1 2 3 4
-3 -2 -1 0
NI-R STAINLESSDUCTILE
SINGLE STAGE PERFORMANCE
480 SERIES
US gpm
Pow
er -
hp
6005004003002001000
2.5
NPSH
r - ft
6005004003002000 100
10
20
Head
- ft
600500400
10
300
20
200100
30
6.344 in6.344 in
6.063 in
5.75 in
71
71
71
71
77
77
77
77
80
80
81
81
-2 0 -1 -2
-2 -2 -2 -5
°
10LS 1760 RPM
JANUARY 2010
TURBINE PUMP CURVE
IMPELLER DATA
PUMP MATERIAL EFFICIENCY CORRECTION
FLANGED BOWL DATAIMPELLER NUMBER 3103TYPE SEMI-OPENTHRUST FACTOR K=7.50EYE AREA 11.7 SQ. IN.WEIGHT 6.25 LB.
Minimum submergence aboveeye of bottom impeller: 38 IN.
Performance based on pumping clear, fresh water at a temperature not over 85 F., free of gas, air or abrasives and with bowls properlyadjusted and submerged. Performance curve reflects Hydraulic Institute tolerances and guidelines.
IMPELLER MATERIAL:BOWL MATERIAL:
BRONZE
BOWL NUMBER 3098BOWL MAX. DIAMETER 9.500 IN.BOWL MIN. DIAMETER 9.250 IN.MAX. NO. STAGES 34ONE STAGE WEIGHT 230 LB.ADD STAGE WEIGHT 55 LB.STD. SHAFT DIA. 1.500 IN.STD. LATERAL 0.500 IN.DISCHARGE SIZE 6 - 8 IN.DISCHARGE CONNECTION THD - FLGSUCTION SIZE 6 - 8 IN.SUCTION CONNECTION THDMAX. SPHERE SIZE 0.500 IN.MAX. OPERATIONAL P.S.I. 595 (SPECIAL)
EFFICIENCY CORRECTIONNUMBER OF BOWLS:CHANGE AS FOLLOWS:
CHANGE IN EFFICIENCY MAY AFFECT BOTH HEAD AND HORSEPOWER.
1 2 3 4
-4 -2 -1 0
NI-R STAINLESSDUCTILE
SINGLE STAGE PERFORMANCE
480 SERIES
US gpm
Pow
er -
hp
6005004003002001000
5
NPSH
r - ft
6005004003002000 100
10
Head
- ft
600500400
20
300
30
200
40
100
50
60 7.688 in7.688 in
7.5 in
6.875 in
65
65
65
65
70
70
70
70
75
75 75
75
78
78
78
78
80
80
80
80
81
81
8282
-1 0 -1 -2
-2 -2 -1 -3
°
10MS 1760 RPM
JANUARY 2010
TURBINE PUMP CURVE
IMPELLER DATA
PUMP MATERIAL EFFICIENCY CORRECTION
FLANGED BOWL DATAIMPELLER NUMBER 3099TYPE SEMI-OPENTHRUST FACTOR K=7.50EYE AREA 11.7 SQ. IN.WEIGHT 5.75 LB.
Minimum submergence aboveeye of bottom impeller: 38 IN.
Performance based on pumping clear, fresh water at a temperature not over 85 F., free of gas, air or abrasives and with bowls properlyadjusted and submerged. Performance curve reflects Hydraulic Institute tolerances and guidelines.
IMPELLER MATERIAL:BOWL MATERIAL:
BRONZE
BOWL NUMBER 3098BOWL MAX. DIAMETER 9.500 IN.BOWL MIN. DIAMETER 9.250 IN.MAX. NO. STAGES 30ONE STAGE WEIGHT 230 LB.ADD STAGE WEIGHT 55 LB.STD. SHAFT DIA. 1.500 IN.STD. LATERAL 0.625 IN.DISCHARGE SIZE 6 - 8 IN.DISCHARGE CONNECTION THD - FLGSUCTION SIZE 6 - 8 IN.SUCTION CONNECTION THDMAX. SPHERE SIZE 0.625 IN.MAX. OPERATIONAL P.S.I. 595 (SPECIAL)
EFFICIENCY CORRECTIONNUMBER OF BOWLS:CHANGE AS FOLLOWS:
CHANGE IN EFFICIENCY MAY AFFECT BOTH HEAD AND HORSEPOWER.
1 2 3 4
-4 -2 -1 0
NI-R STAINLESSDUCTILE
SINGLE STAGE PERFORMANCE
480 SERIES
US gpm
Pow
er -
hp
8007006005004003002000 100
5
10
NPSH
r - ft
8007006005004003002000 100
10
20
Head
- ft
800700600500400
20
30
300
40
200
50
100
60
7.688 in7.688 in
7.5 in
6.875 in
65
65
65
65
70
70
70
70
75
7575
75
78
78
78
78
80
80
81
81
82
82
8383
-1 0 -1 -2
-2 -2 -1 -3
°
10HS 1760 RPM
JANUARY 2010
TURBINE PUMP CURVE
IMPELLER DATA
PUMP MATERIAL EFFICIENCY CORRECTION
FLANGED BOWL DATAIMPELLER NUMBER 2969TYPE SEMI-OPENTHRUST FACTOR K=9.20EYE AREA 14.9 SQ. IN.WEIGHT 5.25 LB.
Minimum submergence aboveeye of bottom impeller: 27 IN.
Performance based on pumping clear, fresh water at a temperature not over 85 F., free of gas, air or abrasives and with bowls properlyadjusted and submerged. Performance curve reflects Hydraulic Institute tolerances and guidelines.
IMPELLER MATERIAL:BOWL MATERIAL:
BRONZE
BOWL NUMBER 2968BOWL MAX. DIAMETER 9.500 IN.BOWL MIN. DIAMETER 9.250 IN.MAX. NO. STAGES 28ONE STAGE WEIGHT 230 LB.ADD STAGE WEIGHT 55 LB.STD. SHAFT DIA. 1.500 IN.STD. LATERAL 0.625 IN.DISCHARGE SIZE 6 - 8 IN.DISCHARGE CONNECTION THD - FLGSUCTION SIZE 6 - 8 IN.SUCTION CONNECTION THDMAX. SPHERE SIZE 0.500 IN.MAX. OPERATIONAL P.S.I. 595 (SPECIAL)
EFFICIENCY CORRECTIONNUMBER OF BOWLS:CHANGE AS FOLLOWS:
CHANGE IN EFFICIENCY MAY AFFECT BOTH HEAD AND HORSEPOWER.
1 2 3 4
-4 -2 -1 0
NI-R STAINLESSDUCTILE
SINGLE STAGE PERFORMANCE
480 SERIES
US gpm
Pow
er -
hp
9008007006005004003002000 100
5
10
NPSH
r - ft
9008007006005004003002000 100
10
20
Head
- ft
900800700600500
20
400
30
300
40
200
50
100
60
80
7.688 in7.688 in7.5 in
7.125 in
66
66
66
66
70
70
70
70
76
76 76
76
78
78
78
78
80
-1 0 -1 -2
-2 -2 -1 -3
°
10WS 1760 RPM
JANUARY 2010
TURBINE PUMP CURVE
IMPELLER DATA
PUMP MATERIAL EFFICIENCY CORRECTION
FLANGED BOWL DATAIMPELLER NUMBER 3542TYPE SEMI-OPENTHRUST FACTOR K=11.20EYE AREA 19.4 SQ. IN.WEIGHT 7.25 LB.
Minimum submergence aboveeye of bottom impeller: 28 IN.
Performance based on pumping clear, fresh water at a temperature not over 85 F., free of gas, air or abrasives and with bowls properlyadjusted and submerged. Performance curve reflects Hydraulic Institute tolerances and guidelines.
IMPELLER MATERIAL:BOWL MATERIAL:
BRONZE
BOWL NUMBER 3541BOWL MAX. DIAMETER 9.875 IN.BOWL MIN. DIAMETER 9.500 IN.MAX. NO. STAGES 28ONE STAGE WEIGHT 250 LB.ADD STAGE WEIGHT 60 LB.STD. SHAFT DIA. 1.688 IN.STD. LATERAL 0.875 IN.DISCHARGE SIZE 6 - 8 IN.DISCHARGE CONNECTION THD - FLGSUCTION SIZE 6 - 8 IN.SUCTION CONNECTION THDMAX. SPHERE SIZE 0.875 IN.MAX. OPERATIONAL P.S.I. 455 (SPECIAL)
EFFICIENCY CORRECTIONNUMBER OF BOWLS:CHANGE AS FOLLOWS:
CHANGE IN EFFICIENCY MAY AFFECT BOTH HEAD AND HORSEPOWER.
1 2 3 4
-4 -2 -1 0
NI-R STAINLESSDUCTILE
SINGLE STAGE PERFORMANCE
480 SERIES
US gpm
Powe
r - h
p
13001200110010009008007006005004003002000
5
100
10
NPSH
r - ft
13001200110010009008007006005004003000 200
10
100
20
Head
- ft
1300120011001000900800700
10
600
20
500
30
400
40
300
50
200100
60
8.25 in8.25 in
7.75 in
6.75 in
60
60
60
60
64
64 64
64
68
68
68
68
72
72
72
72
74
74
74
74
76
76
76
76
78
78
80
80
81
-1 0 -1 -2
-2 -2 -1 -3
°
10YS 1760 RPM
JANUARY 2010
TURBINE PUMP CURVE
IMPELLER DATA
PUMP MATERIAL EFFICIENCY CORRECTION
FLANGED BOWL DATAIMPELLER NUMBER 3542TYPE SEMI-OPENTHRUST FACTOR K=11.40EYE AREA 19.4 SQ. IN.WEIGHT 7.25 LB.
Minimum submergence aboveeye of bottom impeller: 28IN.
Performance based on pumping clear, fresh water at a temperature not over 85 F., free of gas, air or abrasives and with bowls properlyadjusted and submerged. Performance curve reflects Hydraulic Institute tolerances and guidelines.
IMPELLER MATERIAL:BOWL MATERIAL:
BRONZE
BOWL NUMBER 3541BOWL MAX. DIAMETER 9.875 IN.BOWL MIN. DIAMETER 9.500 IN.MAX. NO. STAGES 28ONE STAGE WEIGHT 250 LB.ADD STAGE WEIGHT 60 LB.STD. SHAFT DIA. 1.688 IN.STD. LATERAL 0.750 IN.DISCHARGE SIZE 6 - 8 IN.DISCHARGE CONNECTION THD - FLGSUCTION SIZE 6 - 8 IN.SUCTION CONNECTION THDMAX. SPHERE SIZE 0.875 IN.MAX. OPERATIONAL P.S.I. 455 (SPECIAL)
EFFICIENCY CORRECTIONNUMBER OF BOWLS:CHANGE AS FOLLOWS:
CHANGE IN EFFICIENCY MAY AFFECT BOTH HEAD AND HORSEPOWER.
1 2 3 4
-4 -2 -1 0
NI-R STAINLESSDUCTILE
SINGLE STAGE PERFORMANCE
480 SERIES
US gpm
Pow
er -
hp
125010007505002500
10
NPSH
r - ft
125010007505002500
10
20
Head
- ft
12501000750
10
20
500
30
40
250
50
608.25 in8.25 in
7.75 in
6.75 in
64
64 64
64
68
68
68
68
72
72
72
72
74
74
74
74
76
76
76
76
78
78
79
79
8080
81
-1 0 -1 -2
-2 -2 -1 -3
°
10ZS 1760 RPM
JANUARY 2010
TURBINE PUMP CURVE
IMPELLER DATA
PUMP MATERIAL EFFICIENCY CORRECTION
FLANGED BOWL DATAIMPELLER NUMBER 3863TYPE SEMI-OPENTHRUST FACTOR K=13.50EYE AREA 26.7 SQ. IN.WEIGHT 5.75 LB.
Minimum submergence aboveeye of bottom impeller: 30 IN.
Performance based on pumping clear, fresh water at a temperature not over 85 F., free of gas, air or abrasives and with bowls properlyadjusted and submerged. Performance curve reflects Hydraulic Institute tolerances and guidelines.
IMPELLER MATERIAL:BOWL MATERIAL:
BRONZE
BOWL NUMBER 3864BOWL MAX. DIAMETER 9.875 IN.BOWL MIN. DIAMETER 9.500 IN.MAX. NO. STAGES 26ONE STAGE WEIGHT 250 LB.ADD STAGE WEIGHT 60 LB.STD. SHAFT DIA. 1.688 IN.STD. LATERAL 0.500 IN.DISCHARGE SIZE 6 - 8 IN.DISCHARGE CONNECTION THD - FLGSUCTION SIZE 6 - 8 IN.SUCTION CONNECTION THDMAX. SPHERE SIZE 1.438 IN.MAX. OPERATIONAL P.S.I. 455 (SPECIAL)
EFFICIENCY CORRECTIONNUMBER OF BOWLS:CHANGE AS FOLLOWS:
CHANGE IN EFFICIENCY MAY AFFECT BOTH HEAD AND HORSEPOWER.
1 2 3 4 5
-5 -4 -2 -1 0
NI-R STAINLESSDUCTILE
SINGLE STAGE PERFORMANCE
480 SERIES
US gpm
Pow
er -
hp
200017501500125010007505000 250
10
NPSH
r - ft
200017501500125010007505000 250
10
20
30
Head
- ft
200017501500125010
1000
20
750
30
500
40
250
50
8.25 in8.25 in
7.875 in
7.125 in
70
70
70
70
75
75
75
75
78
78
80
80
81
81
82
82
-1 0 -1 -2
-2 -2 -1 -3
°
12IS 1760 RPM
JANUARY 2010
TURBINE PUMP CURVE
IMPELLER DATA
PUMP MATERIAL EFFICIENCY CORRECTION
FLANGED BOWL DATAIMPELLER NUMBER 2997TYPE SEMI-OPENTHRUST FACTOR K=8.20EYE AREA 18.1 SQ. IN.WEIGHT 9.50 LB.
Minimum submergence aboveeye of bottom impeller: 30 IN.
Performance based on pumping clear, fresh water at a temperature not over 85 F., free of gas, air or abrasives and with bowls properlyadjusted and submerged. Performance curve reflects Hydraulic Institute tolerances and guidelines.
IMPELLER MATERIAL:BOWL MATERIAL:
BRONZE
BOWL NUMBER 2994BOWL MAX. DIAMETER 12.000 IN.BOWL MIN. DIAMETER 11.500 IN.MAX. NO. STAGES 19ONE STAGE WEIGHT 340 LB.ADD STAGE WEIGHT 100 LB.STD. SHAFT DIA. 1.688 IN.STD. LATERAL 0.625 IN.DISCHARGE SIZE 8 - 10 IN.DISCHARGE CONNECTION THD - FLGSUCTION SIZE 8 - 10 IN.SUCTION CONNECTION THDMAX. SPHERE SIZE 0.625 IN.MAX. OPERATIONAL P.S.I. 585 (SPECIAL)
EFFICIENCY CORRECTIONNUMBER OF BOWLS:CHANGE AS FOLLOWS:
CHANGE IN EFFICIENCY MAY AFFECT BOTH HEAD AND HORSEPOWER.
1 2 3 4
-4 -3 -2 -1
NI-R STAINLESSDUCTILE
SINGLE STAGE PERFORMANCE
480 SERIES
US gpm
Pow
er -
hp
9008007006005004003002000 100
10
20
NPSH
r - ft
9008007006005004003002000 100
10
Head
- ft
900800700600500
40
400
50
300
60
70
200
80
100
90 9.313 in9.313 in
8.75 in
8.25 in
81
8181
81
83
83
83
83
84
84
86
-2 0 -1 -2
-2 -1 -2 -3
°
12KS 1760 RPM
JANUARY 2010
TURBINE PUMP CURVE
IMPELLER DATA
PUMP MATERIAL EFFICIENCY CORRECTION
FLANGED BOWL DATAIMPELLER NUMBER 2992TYPE SEMI-OPENTHRUST FACTOR K=7.75EYE AREA 20.4 SQ. IN.WEIGHT 9.00 LB.
Minimum submergence aboveeye of bottom impeller: 30 IN.
Performance based on pumping clear, fresh water at a temperature not over 85 F., free of gas, air or abrasives and with bowls properlyadjusted and submerged. Performance curve reflects Hydraulic Institute tolerances and guidelines.
IMPELLER MATERIAL:BOWL MATERIAL:
BRONZE
BOWL NUMBER 2994BOWL MAX. DIAMETER 12.000 IN.BOWL MIN. DIAMETER 11.500 IN.MAX. NO. STAGES 16ONE STAGE WEIGHT 340 LB.ADD STAGE WEIGHT 100 LB.STD. SHAFT DIA. 1.688 IN.STD. LATERAL 0.500 IN.DISCHARGE SIZE 8 - 10 IN.DISCHARGE CONNECTION THD - FLGSUCTION SIZE 8 - 10 IN.SUCTION CONNECTION THDMAX. SPHERE SIZE 0.625 IN.MAX. OPERATIONAL P.S.I. 584 (SPECIAL)
EFFICIENCY CORRECTIONNUMBER OF BOWLS:CHANGE AS FOLLOWS:
CHANGE IN EFFICIENCY MAY AFFECT BOTH HEAD AND HORSEPOWER.
1 2 3 4 5
-4 -3 -2 -1 0
NI-R STAINLESSDUCTILE
SINGLE STAGE PERFORMANCE
480 SERIES
US gpm
Pow
er -
hp
110010009008007006005004003002000 100
10
20
NPSH
r - ft
110010009008007006005004003002000 100
10
Head
- ft
1100100090080070060040
500
50
400
60
300
70
200
80
100
90 9.313 in9.313 in
8.75 in
7.938 in
80
80
80
80
81
81
83
83
83
83
84
84
-2 0 -1 -2
-2 -1 -2 -3
°
12LS 1760 RPM
JANUARY 2010
TURBINE PUMP CURVE
IMPELLER DATA
PUMP MATERIAL EFFICIENCY CORRECTION
FLANGED BOWL DATAIMPELLER NUMBER 3779TYPE SEMI-OPENTHRUST FACTOR K=12.50EYE AREA 20.1 SQ. IN.WEIGHT 8.13 LB.
Minimum submergence aboveeye of bottom impeller: 30 IN.
Performance based on pumping clear, fresh water at a temperature not over 85 F., free of gas, air or abrasives and with bowls properlyadjusted and submerged. Performance curve reflects Hydraulic Institute tolerances and guidelines.
IMPELLER MATERIAL:BOWL MATERIAL:
BRONZE
BOWL NUMBER 2952BOWL MAX. DIAMETER 11.563 IN.BOWL MIN. DIAMETER 11.250 IN.MAX. NO. STAGES 19ONE STAGE WEIGHT 340 LB.ADD STAGE WEIGHT 100 LB.STD. SHAFT DIA. 1.688 IN.STD. LATERAL 0.875 IN.DISCHARGE SIZE 8 - 10 IN.DISCHARGE CONNECTION THD - FLGSUCTION SIZE 8 - 10 IN.SUCTION CONNECTION THDMAX. SPHERE SIZE 0.625 IN.MAX. OPERATIONAL P.S.I. 584 (SPECIAL)
EFFICIENCY CORRECTIONNUMBER OF BOWLS:CHANGE AS FOLLOWS:
CHANGE IN EFFICIENCY MAY AFFECT BOTH HEAD AND HORSEPOWER.
1 2 3 4
-4 -2 -1 0
NI-R STAINLESSDUCTILE
SINGLE STAGE PERFORMANCE
480 SERIES
US gpm
Pow
er -
hp
13001200110010009008007006005004003002000 100
10
20
NPSH
r - ft
13001200110010009008007006005004003000 200
10
100
20
Head
- ft
130012001100100090080020 700
30
600
40
500400
50
300
60
200
70
100
80
9.375 in9.375 in
8.75 in
7.75 in
70
70
70
70
75
75 75
75
78
78
78
78
80
80
80
80
82
82
83
83
83
-2 0 -1 -2
-2 -1 -2 -3
°
12MS 1760 RPM
JANUARY 2010
TURBINE PUMP CURVE
IMPELLER DATA
PUMP MATERIAL EFFICIENCY CORRECTION
FLANGED BOWL DATAIMPELLER NUMBER 2956TYPE SEMI-OPENTHRUST FACTOR K=12.50EYE AREA 20.1 SQ. IN.WEIGHT 10.00 LB.
Minimum submergence aboveeye of bottom impeller: 30 IN.
Performance based on pumping clear, fresh water at a temperature not over 85 F., free of gas, air or abrasives and with bowls properlyadjusted and submerged. Performance curve reflects Hydraulic Institute tolerances and guidelines.
IMPELLER MATERIAL:BOWL MATERIAL:
BRONZE
BOWL NUMBER 2952BOWL MAX. DIAMETER 11.563 IN.BOWL MIN. DIAMETER 11.250 IN.MAX. NO. STAGES 14ONE STAGE WEIGHT 340 LB.ADD STAGE WEIGHT 100 LB.STD. SHAFT DIA. 1.688 IN.STD. LATERAL 0.750 IN.DISCHARGE SIZE 8 - 10 IN.DISCHARGE CONNECTION THD - FLGSUCTION SIZE 8 - 10 IN.SUCTION CONNECTION THDMAX. SPHERE SIZE 0.625 IN.MAX. OPERATIONAL P.S.I. 584 (SPECIAL)
EFFICIENCY CORRECTIONNUMBER OF BOWLS:CHANGE AS FOLLOWS:
CHANGE IN EFFICIENCY MAY AFFECT BOTH HEAD AND HORSEPOWER.
1 2 3 4
-3 -2 -1 0
NI-R STAINLESSDUCTILE
SINGLE STAGE PERFORMANCE
480 SERIES
US gpm
Pow
er -
hp
1500125010007505002500
10
20
30
NPSH
r - ft
1500125010007505000 250
10
20
30
Head
- ft
150012501000
25
750
50
500250
75
9.375 in9.375 in
9 in
8.625 in
8 in
65
65
65
65
70
70 70
70
75
75
75
75
80
80
82
83
-2 0 -1 -2
-2 -1 -2 -3
°
12HS 1760 RPM
JANUARY 2010
TURBINE PUMP CURVE
IMPELLER DATA
PUMP MATERIAL EFFICIENCY CORRECTION
FLANGED BOWL DATAIMPELLER NUMBER 2953TYPE SEMI-OPENTHRUST FACTOR K=19.00EYE AREA 32.4 SQ. IN.WEIGHT 11.25 LB.
Minimum submergence aboveeye of bottom impeller: 30 IN.
Performance based on pumping clear, fresh water at a temperature not over 85 F., free of gas, air or abrasives and with bowls properlyadjusted and submerged. Performance curve reflects Hydraulic Institute tolerances and guidelines.
IMPELLER MATERIAL:BOWL MATERIAL:
BRONZE
BOWL NUMBER 2915BOWL MAX. DIAMETER 11.563 IN.BOWL MIN. DIAMETER 11.250 IN.MAX. NO. STAGES 15ONE STAGE WEIGHT 340 LB.ADD STAGE WEIGHT 100 LB.STD. SHAFT DIA. 1.688 IN.STD. LATERAL 0.750 IN.DISCHARGE SIZE 8 - 10 IN.DISCHARGE CONNECTION THD - FLGSUCTION SIZE 8 - 10 IN.SUCTION CONNECTION THDMAX. SPHERE SIZE 0.750 IN.MAX. OPERATIONAL P.S.I. 584 (SPECIAL)
EFFICIENCY CORRECTIONNUMBER OF BOWLS:CHANGE AS FOLLOWS:
CHANGE IN EFFICIENCY MAY AFFECT BOTH HEAD AND HORSEPOWER.
1 2 3 4
-4 -2 -1 0
NI-R STAINLESSDUCTILE
SINGLE STAGE PERFORMANCE
480 SERIES
US gpm
Pow
er -
hp
17501500125010007505000 250
10
20
30
NPSH
r - ft
17501500125010007505000 250
10
20
Head
- ft
17501500125025 1000750
50
500
75
250
9.563 in9.563 in
9.281 in
8.875 in 70
70
70
70
75
75 75
75
78
78
78
78
80
80
80
80
82
82
83
83
84
8485
-2 0 -1 -2
-2 -1 -2 -3
°
12XS 1760 RPM
JANUARY 2010
TURBINE PUMP CURVE
IMPELLER DATA
PUMP MATERIAL EFFICIENCY CORRECTION
FLANGED BOWL DATAIMPELLER NUMBER 3374TYPE SEMI-OPENTHRUST FACTOR K=20.80EYE AREA 35.6 SQ. IN.WEIGHT 11.50 LB.
Minimum submergence aboveeye of bottom impeller: 30 IN.
Performance based on pumping clear, fresh water at a temperature not over 85 F., free of gas, air or abrasives and with bowls properlyadjusted and submerged. Performance curve reflects Hydraulic Institute tolerances and guidelines.
IMPELLER MATERIAL:BOWL MATERIAL:
BRONZE
BOWL NUMBER 3361BOWL MAX. DIAMETER 11.563 IN.BOWL MIN. DIAMETER 11.250 IN.MAX. NO. STAGES 11ONE STAGE WEIGHT 340 LB.ADD STAGE WEIGHT 100 LB.STD. SHAFT DIA. 1.688 IN.STD. LATERAL 0.875 IN.DISCHARGE SIZE 8 - 10 IN.DISCHARGE CONNECTION THD - FLGSUCTION SIZE 8 - 10 IN.SUCTION CONNECTION THDMAX. SPHERE SIZE 1.000 IN.MAX. OPERATIONAL P.S.I. 584 (SPECIAL)
EFFICIENCY CORRECTIONNUMBER OF BOWLS:CHANGE AS FOLLOWS:
CHANGE IN EFFICIENCY MAY AFFECT BOTH HEAD AND HORSEPOWER.
1 2 3 4
-4 -2 -1 0
NI-R STAINLESSDUCTILE
SINGLE STAGE PERFORMANCE
480 SERIES
US gpm
Pow
er -
hp
2250200017501500125010007505000 250
10
20
30
NPSH
r - ft
2250200017501500125010007505000 250
10
20
Head
- ft
2250200017501500125020
30
1000
40
750
50
500
60
70
250
80
9.563 in9.563 in
8.875 in
71
71
71
71
80
80
80
80
82
82 82
82
83
83
-2 0 -1 -2
-2 -1 -2 -3
°
12WS 1760 RPM
JANUARY 2010
TURBINE PUMP CURVE
IMPELLER DATA
PUMP MATERIAL EFFICIENCY CORRECTION
FLANGED BOWL DATAIMPELLER NUMBER 4777TYPE SEMI-OPENTHRUST FACTOR K=17.40EYE AREA 29.7 SQ. IN.WEIGHT 14.50 LB.
Minimum submergence aboveeye of bottom impeller: 32 IN.
Performance based on pumping clear, fresh water at a temperature not over 85 F., free of gas, air or abrasives and with bowls properlyadjusted and submerged. Performance curve reflects Hydraulic Institute tolerances and guidelines.
IMPELLER MATERIAL:BOWL MATERIAL:
BRONZE
BOWL NUMBER 4771BOWL MAX. DIAMETER 12.188 IN.BOWL MIN. DIAMETER 11.750 IN.MAX. NO. STAGES 9ONE STAGE WEIGHT 415 LB.ADD STAGE WEIGHT 140 LB.STD. SHAFT DIA. 1.688 IN.STD. LATERAL 0.750 IN.DISCHARGE SIZE 8 - 10 IN.DISCHARGE CONNECTION THD - FLGSUCTION SIZE 8 - 10 IN.SUCTION CONNECTION THDMAX. SPHERE SIZE 1.375 IN.MAX. OPERATIONAL P.S.I. 584 (SPECIAL)
EFFICIENCY CORRECTIONNUMBER OF BOWLS:CHANGE AS FOLLOWS:
CHANGE IN EFFICIENCY MAY AFFECT BOTH HEAD AND HORSEPOWER.
1 2 3 4
-3 -2 -1 0
NI-R STAINLESSDUCTILE
SINGLE STAGE PERFORMANCE
480 SERIES
US gpm
Pow
er -
hp
25002250200017501500125010007505000 250
25
NPSH
r - ft
25002250200017501500125010007505000 250
25
Head
- ft
25002250200017501500
40
1250
50
1000
60
750
70
500
80
250
90 10.063 in10.063 in
9.75 in
9.375 in72
72
78
78
81
81 81
81
83
83
83
83
8484
-2 0 -1 -2
-2 -1 -2 -3
°
12YS 1760 RPM
JANUARY 2010
TURBINE PUMP CURVE
IMPELLER DATA
PUMP MATERIAL EFFICIENCY CORRECTION
FLANGED BOWL DATAIMPELLER NUMBER 4778TYPE SEMI-OPENTHRUST FACTOR K=16.50EYE AREA 38.0 SQ. IN.WEIGHT 19.00 LB.
Minimum submergence aboveeye of bottom impeller: 36 IN.
Performance based on pumping clear, fresh water at a temperature not over 85 F., free of gas, air or abrasives and with bowls properlyadjusted and submerged. Performance curve reflects Hydraulic Institute tolerances and guidelines.
IMPELLER MATERIAL:BOWL MATERIAL:
BRONZE
BOWL NUMBER 4772BOWL MAX. DIAMETER 12.188 IN.BOWL MIN. DIAMETER 11.750 IN.MAX. NO. STAGES 8ONE STAGE WEIGHT 415 LB.ADD STAGE WEIGHT 140 LB.STD. SHAFT DIA. 1.688 IN.STD. LATERAL 0.875 IN.DISCHARGE SIZE 8 - 10 IN.DISCHARGE CONNECTION THD - FLGSUCTION SIZE 8 - 10 IN.SUCTION CONNECTION THDMAX. SPHERE SIZE 1.500 IN.MAX. OPERATIONAL P.S.I. 584 (SPECIAL)
EFFICIENCY CORRECTIONNUMBER OF BOWLS:CHANGE AS FOLLOWS:
CHANGE IN EFFICIENCY MAY AFFECT BOTH HEAD AND HORSEPOWER.
1 2 3 4
-4 -2 -1 0
NI-R STAINLESSDUCTILE
SINGLE STAGE PERFORMANCE
480 SERIES
US gpm
Pow
er -
hp
300025002000150010005000
25
50
NPSH
r - ft
300025002000150010000 500
25
Head
- ft
30002500200030
1500
40
1000
50
60
500
70
80 9.5 in9.5 in
9 in
8.625 in78
7878
78
80
80
80
8081
81
82
82
-2 0 -1 -2
-2 -1 -2 -3
°
14LS 1750 RPM
JANUARY 2010
TURBINE PUMP CURVE
IMPELLER DATA
PUMP MATERIAL EFFICIENCY CORRECTION
FLANGED BOWL DATAIMPELLER NUMBER 3107TYPE ENCLOSEDTHRUST FACTOR K=19.70EYE AREA 31.5 SQ. IN.WEIGHT 18.50 LB.
Minimum submergence aboveeye of bottom impeller: 30 IN.
Performance based on pumping clear, fresh water at a temperature not over 85 F., free of gas, air or abrasives and with bowls properlyadjusted and submerged. Performance curve reflects Hydraulic Institute tolerances and guidelines.
IMPELLER MATERIAL:BOWL MATERIAL:
BRONZE
BOWL NUMBER 3106BOWL MAX. DIAMETER 13.500 IN.BOWL MIN. DIAMETER 13.250 IN.MAX. NO. STAGES 12ONE STAGE WEIGHT 490 LB.ADD STAGE WEIGHT 175 LB.STD. SHAFT DIA. 1.938 IN.STD. LATERAL 0.875 IN.DISCHARGE SIZE 10 - 12 IN.DISCHARGE CONNECTION THD - FLGSUCTION SIZE 10 - 12 IN.SUCTION CONNECTION THDMAX. SPHERE SIZE 0.750 IN.MAX. OPERATIONAL P.S.I. 540 (SPECIAL)
EFFICIENCY CORRECTIONNUMBER OF BOWLS:CHANGE AS FOLLOWS:
CHANGE IN EFFICIENCY MAY AFFECT BOTH HEAD AND HORSEPOWER.
1 2 3
-2 -1 0
NI-R STAINLESSDUCTILE
SINGLE STAGE PERFORMANCE
480 SERIES
US gpm
Pow
er -
hp
2250200017501500125010007505000 250
25
50
NPSH
r - ft
2250200017501500125010007505000 250
10
20
30
Head
- ft
22502000175015001250
50
1000
75
750500
100
250
125
11.313 in11.313 in
10.688 in
10.313 in
75
75
75
75
78
78 78
78
80
8080
80
82
82
84
84
85
85
-2 0 -1 -1
-2 -1 -2 -2
°
14MS 1750 RPM
JANUARY 2010
TURBINE PUMP CURVE
IMPELLER DATA
PUMP MATERIAL EFFICIENCY CORRECTION
FLANGED BOWL DATAIMPELLER NUMBER 3078TYPE SEMI-OPENTHRUST FACTOR K=23.40EYE AREA 40.9 SQ. IN.WEIGHT 20.25 LB.
Minimum submergence aboveeye of bottom impeller: 30 IN.
Performance based on pumping clear, fresh water at a temperature not over 85 F., free of gas, air or abrasives and with bowls properlyadjusted and submerged. Performance curve reflects Hydraulic Institute tolerances and guidelines.
IMPELLER MATERIAL:BOWL MATERIAL:
BRONZE
BOWL NUMBER 3042BOWL MAX. DIAMETER 13.500 IN.BOWL MIN. DIAMETER 13.250 IN.MAX. NO. STAGES 10ONE STAGE WEIGHT 490 LB.ADD STAGE WEIGHT 175 LB.STD. SHAFT DIA. 1.938 IN.STD. LATERAL 0.875 IN.DISCHARGE SIZE 10 - 12 IN.DISCHARGE CONNECTION THD - FLGSUCTION SIZE 10 - 12 IN.SUCTION CONNECTION THDMAX. SPHERE SIZE 1.250 IN.MAX. OPERATIONAL P.S.I. 540 (SPECIAL)
EFFICIENCY CORRECTIONNUMBER OF BOWLS:CHANGE AS FOLLOWS:
CHANGE IN EFFICIENCY MAY AFFECT BOTH HEAD AND HORSEPOWER.
1 2 3 4
-3 -2 -1 0
NI-R STAINLESSDUCTILE
SINGLE STAGE PERFORMANCE
480 SERIES
US gpm
Pow
er -
hp
300025002000150010005000
25
50
NPSH
r - ft
300025002000150010005000
25
Head
- ft
3000250020001500
50
1000
75
500
100
12511.313 in11.313 in
11 in
10.688 in
70
70
70
70
75
75
75
75
78
78
78
78
80
80 80
80
82
8282
82
83
83
84
84
-2 0 -1 -1
-2 -1 -2 -2
°
14HS 1760 RPM
JANUARY 2010
TURBINE PUMP CURVE
IMPELLER DATA
PUMP MATERIAL EFFICIENCY CORRECTION
FLANGED BOWL DATAIMPELLER NUMBER 3029TYPE SEMI-OPENTHRUST FACTOR K=25.20EYE AREA 43.9 SQ. IN.WEIGHT 21.25 LB.
Minimum submergence aboveeye of bottom impeller: 32 IN.
Performance based on pumping clear, fresh water at a temperature not over 85 F., free of gas, air or abrasives and with bowls properlyadjusted and submerged. Performance curve reflects Hydraulic Institute tolerances and guidelines.
IMPELLER MATERIAL:BOWL MATERIAL:
BRONZE
BOWL NUMBER 3042BOWL MAX. DIAMETER 13.500 IN.BOWL MIN. DIAMETER 13.250 IN.MAX. NO. STAGES 9ONE STAGE WEIGHT 490 LB.ADD STAGE WEIGHT 175 LB.STD. SHAFT DIA. 1.938 IN.STD. LATERAL 0.875 IN.DISCHARGE SIZE 10 - 12 IN.DISCHARGE CONNECTION THD - FLGSUCTION SIZE 10 - 12 IN.SUCTION CONNECTION THDMAX. SPHERE SIZE 1.250 IN.MAX. OPERATIONAL P.S.I. 540 (SPECIAL)
EFFICIENCY CORRECTIONNUMBER OF BOWLS:CHANGE AS FOLLOWS:
CHANGE IN EFFICIENCY MAY AFFECT BOTH HEAD AND HORSEPOWER.
1 2 3 4
-3 -2 -1 0
NI-R STAINLESSDUCTILE
SINGLE STAGE PERFORMANCE
480 SERIES
US gpm
Pow
er -
hp
300025002000150010005000
50
NPSH
r - ft
300025002000150010000 500
25
Head
- ft
3000250020001500
50
75
1000
100
500
125
11.313 in11.313 in
10.844 in
10.5 in
70
70
75
75
77
7778
78
80
8080
80
82
82
82
82
83
83
83
83
8484
-2 0 -1 -1
-2 -1 -2 -2
°
14XS 1750 RPM
JANUARY 2010
TURBINE PUMP CURVE
IMPELLER DATA
PUMP MATERIAL EFFICIENCY CORRECTION
FLANGED BOWL DATAIMPELLER NUMBER 3092TYPE SEMI-OPENTHRUST FACTOR K=23.40EYE AREA 40.9 SQ. IN.WEIGHT 20.25 LB.
Minimum submergence aboveeye of bottom impeller: 32 IN.
Performance based on pumping clear, fresh water at a temperature not over 85 F., free of gas, air or abrasives and with bowls properlyadjusted and submerged. Performance curve reflects Hydraulic Institute tolerances and guidelines.
IMPELLER MATERIAL:BOWL MATERIAL:
BRONZE
BOWL NUMBER 3042BOWL MAX. DIAMETER 13.500 IN.BOWL MIN. DIAMETER 13.250 IN.MAX. NO. STAGES 8ONE STAGE WEIGHT 490 LB.ADD STAGE WEIGHT 175 LB.STD. SHAFT DIA. 1.938 IN.STD. LATERAL 0.875 IN.DISCHARGE SIZE 10 - 12 IN.DISCHARGE CONNECTION THD - FLGSUCTION SIZE 10 - 12 IN.SUCTION CONNECTION THDMAX. SPHERE SIZE 1.250 IN.MAX. OPERATIONAL P.S.I. 540 (SPECIAL)
EFFICIENCY CORRECTIONNUMBER OF BOWLS:CHANGE AS FOLLOWS:
CHANGE IN EFFICIENCY MAY AFFECT BOTH HEAD AND HORSEPOWER.
1 2 3 4
-3 -2 -1 0
NI-R STAINLESSDUCTILE
SINGLE STAGE PERFORMANCE
480 SERIES
US gpm
Pow
er -
hp
300025002000150010005000
50
NPSH
r - ft
300025002000150010000 500
25
Head
- ft
300025002000
50
1500
75
1000
100
500
125 11.313 in11.313 in
11 in
10.625 in
75
75
75
75
78
78 78
78
80
80
80
80
81
81
81
81
82
82
83
83
-2 0 -1 -1
-2 -1 -2 -2
°
14WS 1750 RPM
JANUARY 2010
TURBINE PUMP CURVE
IMPELLER DATA
PUMP MATERIAL EFFICIENCY CORRECTION
FLANGED BOWL DATAIMPELLER NUMBER 4153TYPE SEMI-OPENTHRUST FACTOR K=26.20EYE AREA 47.3 SQ. IN.WEIGHT 23.25 LB.
Minimum submergence aboveeye of bottom impeller: 34 IN.
Performance based on pumping clear, fresh water at a temperature not over 85 F., free of gas, air or abrasives and with bowls properlyadjusted and submerged. Performance curve reflects Hydraulic Institute tolerances and guidelines.
IMPELLER MATERIAL:BOWL MATERIAL:
BRONZE
BOWL NUMBER 4152BOWL MAX. DIAMETER 14.063 IN.BOWL MIN. DIAMETER 13.750 IN.MAX. NO. STAGES 9ONE STAGE WEIGHT 500 LB.ADD STAGE WEIGHT 185 LB.STD. SHAFT DIA. 1.938 IN.STD. LATERAL 0.875 IN.DISCHARGE SIZE 10 - 12 IN.DISCHARGE CONNECTION THD - FLGSUCTION SIZE 10 - 12 IN.SUCTION CONNECTION THDMAX. SPHERE SIZE 1.500 IN.MAX. OPERATIONAL P.S.I. 540 (SPECIAL)
EFFICIENCY CORRECTIONNUMBER OF BOWLS:CHANGE AS FOLLOWS:
CHANGE IN EFFICIENCY MAY AFFECT BOTH HEAD AND HORSEPOWER.
1 2 3 4
-4 -2 -1 0
NI-R STAINLESSDUCTILE
SINGLE STAGE PERFORMANCE
480 SERIES
US gpm
Pow
er -
hp
3500300025002000150010000 500
50
NPSH
r - ft
3500300025002000150010000 500
25
Head
- ft
3500300025002000
25
1500
50
75
1000
100
500
125
11.813 in11.813 in
11.5 in
10.5 in
70
70
70
70
75
75
75
75
80
80 80
80
82
8282
82
84
84
86
86
87
87
-2 0 -1 -1
-2 -1 -2 -2
°
15KS 1750 RPM
JANUARY 2010
TURBINE PUMP CURVE
IMPELLER DATA
PUMP MATERIAL EFFICIENCY CORRECTION
FLANGED BOWL DATAIMPELLER NUMBER 0004TYPE SEMI-OPENTHRUST FACTOR K=30.00EYE AREA 63.6 SQ. IN.WEIGHT 21.00 LB.
Minimum submergence aboveeye of bottom impeller: 36 IN.
Performance based on pumping clear, fresh water at a temperature not over 85 F., free of gas, air or abrasives and with bowls properlyadjusted and submerged. Performance curve reflects Hydraulic Institute tolerances and guidelines.
IMPELLER MATERIAL:BOWL MATERIAL:
BRONZE
BOWL NUMBER 0001BOWL MAX. DIAMETER 15.250 IN.BOWL MIN. DIAMETER 14.750 IN.MAX. NO. STAGES 6ONE STAGE WEIGHT 375 LB.ADD STAGE WEIGHT 170 LB.STD. SHAFT DIA. 1.938 IN.STD. LATERAL 0.688 IN.DISCHARGE SIZE 10 - 12 IN.DISCHARGE CONNECTION THD - FLGSUCTION SIZE 10 - 12 IN.SUCTION CONNECTION THDMAX. SPHERE SIZE 2.250 IN.MAX. OPERATIONAL P.S.I. 540 (SPECIAL)
EFFICIENCY CORRECTIONNUMBER OF BOWLS:CHANGE AS FOLLOWS:
CHANGE IN EFFICIENCY MAY AFFECT BOTH HEAD AND HORSEPOWER.
1 2 3 4
-3 -2 -1 0
NI-R STAINLESSDUCTILE
SINGLE STAGE PERFORMANCE
480 SERIES
US gpm
Pow
er -
hp
55005000450040003500300025002000150010000 500
50
100
NPS
Hr -
ft
55005000450040003500300025002000150010000 500
25
50
Hea
d - f
t
550050004500400035003000
25
2500
50
20001500
75
1000
100
500
11.85 in11.85 in
11 in
10.5 in 80
8080
80
81
81
83
83
84
84
-2 0 -1 -1
-2 -1 -2 -2
