FSB® Hardware Handle Styles

Product Series: - E-Series (Inswing & Outswing) - E-Series Stormwatch (Inswing & Outswing) - A-Series Frenchwood (Inswing & Outswing) - A-Series Frenchwood Stormwatch (Inswing) - 400 Series Frenchwood (Inswing & Outswing) - 200 Series (Inswing) - Complementary Curved Top (Inswing & Outswing) - Folding Doors - Residential Entry Doors with Multi-Point Lock (Inswing & Outswing)

Product Type: Hinged Doors

“Andersen” and all other marks where denoted are trademarks of Andersen Corporation. ©2020 Andersen Corporation. All rights reserved. 9173980 BC-00 02/11/2020

FSB® Trim Set Hardware Application

FSB 1035 hardware style shown in guide. Procedure is similar for all styles.

for Active and Passive Hardware

Active hardware application shown in guide. Procedure is similar for passive hardware.

Spanish Version is 9174221

FSB 1102

FSB 1035 FSB 1075

FSB 1076

Read these instructions before starting procedure. For additional information visit www.andersenwindows.com. For questions call 1-888-888-7020.

Para obtener una versión en español de esta guía, visite el sitio andersenwindows.com/accessory guides

WARNING

Passive Hardware

Before installing hardware, install door panels and finish interior wood surfaces of unit.

NOTICE

Active Hardware(with interior thumb turn knob)

· Use caution when working at elevated heights and around window and door openings. Follow the manufacturers’ instructions for ladders and scaffolding. Failure to do so could result in injury or death.· Follow manufacturers’ instructions for hand and power tools. Always wear safety glasses. Failure to do so could result in injury, product or property damage.· Incorrect installation may affect egress and home security. Follow instruction guide to make sure hardware is installed correctly.· Windows and doors have small parts (e.g. hole plugs, operator spline caps, fasteners, etc.). Small parts if swallowed could pose a choking hazard to young children. Dispose of unused, loose, or easily removed small parts. Failure to do so could result in injury.

Tools and Supplies Needed:

Safety Glasses

Phillips Screwdriver Caulk Gun

Sealant

Interior Handle

29173980

Passive Hardware (AP/PA Kits ONLY)(1) Interior Escutcheon Plate(1) Exterior Escutcheon Plate(2) Escutcheon Base Plate(2) Escutcheon Base Plate Screw(2) Escutcheon Base Plate Sleeve Nut(1) Spindle(1) Interior Handle(1) Exterior Handle(2) Set Screw(1) 3 mm Hex Key

Active Hardware(1) Interior Escutcheon Plate(1) Exterior Escutcheon Plate(2) Escutcheon Base Plate(2) Escutcheon Base Plate Screw(2) Escutcheon Base Plate Sleeve Nut(1) Spindle(1) Interior Handle(1) Exterior Handle(2) Set Screw(1) 3 mm Hex Key(1) Latch Strike Plate (2) Receiver Screw(1) Lock Actuator(1) Limiting Plate(2) Limiting Plate Screw(1) Screw Retainer

Keyed Lock Exterior Escutcheon Plate

Exterior Keyed Lock Gasket

Exterior Keyed Lock Kit (optional)(1) Keyed Lock Exterior Escutcheon Plate (1) Exterior Keyed Lock Gasket

3 mm Hex Key

Exterior Escutcheon

Plate

Screw Retainer

ACTIVE Interior EscutcheonPlate

Escutcheon Base Plate Sleeve Nuts

Escutcheon Base Plate Screws

Spindle

3 mm Hex Key

Set Screw

Set Screw

Set Screw

Set Screw

Spindle

Spindle

Lock Actuator

Single Active Latch Strike Plate -A-Series Frenchwood® (Inswing), -400 Series Frenchwood (Inswing),-Andersen Complementary (Inswing)

Color Matched Latch ReceiverScrews

AP/PA Latch Strike Plate-A-Series Frenchwood®(Inswing), -400 Series Frenchwood (Inswing)

Parts Included:

Additional Parts Included:

Limiting Plate

Escutcheon Base Plate

Escutcheon Base Plate

Limiting PlateScrews

Escutcheon Base Plate

Exterior Escutcheon

Plate

Exterior Handle

Escutcheon Base Plate Sleeve Nuts

Interior Handle

Escutcheon Base Plate Screws

Escutcheon Base Plate

Spindle

Exterior Handle

PASSIVE Interior EscutcheonPlate

39173980

2

Insert limiting plate screws and screw retainer as shown. Hold screw retainer on the exterior while tightening screws on the interior.

2

1

Insert lock actuator and limiting plate into lock hole on interior side of door panel as shown.

Construction handle set components cannot be used with standard trim sets. Remove all construction handle set components before installing FSB trim set hardware.

IMPORTANT

Screw Retainer

If optional exterior keyed lock is being installed with patio door hardware, substitute cylinder assembly in place of screw retainer.

NOTICE

Exterior Keyed Lock Cylinder Assembly

Active Hardware Application Only

Active Hardware Application Only

49173980

Fill bottom screw hole with sealant as shown. Position escutcheon base plates over spindle on both sides. Fasten using escutcheon base plate screws and sleeve nuts as shown. (DO NOT fully tighten screws until escutcheon base plates are straight up and down.)

3

Escutcheon base plate screws must be installed from interior and sleeve nuts from exterior to prevent tampering with the handle set from the exterior.

CAUTIONEscutcheon Base Plate Sleeve Nuts (exterior side)

(side view)

Escutcheon Base Plate Screws (interior side)

NOTICEFor optional exterior keyed lock hardware, make sure exterior keyed lock gasket is positioned securely to the exterior escutcheon base plate before applying to panel, as shown.

Exterior Keyed Lock Gasket(for optional exterior keyed lock)

DO NOT overfill hole with sealant or allow sealant to seep out the other side.

59173980

Position interior and exterior escutcheon plates over the escutcheon base plates as shown. Apply firm pressure to top and bottom ends until attachment clips engage.

4

Partially insert set screw into hole on bottom of handles. Slide handles onto spindle, tight to escutcheon plate. Tighten set screws on both handles using 3 mm hex key.

5

Attachment Clip

Attachment Clip

Apply firm pressure to top and bottom ends of both escutcheon plates to engage attachment clips.

Handles must point toward the glass with set screw on the bottom.

Partially insert set screw before applying handle to panel.

69173980

6

Check operation. If handles do not seat or operate smoothly, loosen interior set screw one-quarter turn at a time until handles operate smoothly.

▶ For A-Series Frenchwood® Hinged Patio Doors (Outswing) and 200 Series Hinged Patio Doors (Inswing), discard remaining latch strike plate. Active trim set hardware application is complete.

▶ For A-Series Frenchwood® Hinged Patio Doors (Inswing) and 400 Series Frenchwood® Hinged Patio Doors (Inswing) proceed to next step.

NOTICELabel on edge of panel describes lock operation.

General InformationYour Andersen® hardware has been manufactured of high quality, fine metal. Fine metal requires periodic attention to maintain its beauty and characteristics. Climate, location, and exposure to corrosive environments such as industrial areas, pesticides, herbicides, or salts are challenges to your ability to maintain the hardware’s beauty and characteristics.

Wash hardware using a mild detergent and a soft cloth to remove mild stains, loose dirt, and soil. Avoid abrasive cleaners, cloths, or brushes. When mild detergent and a soft cloth are not adequate, a diluted, household vinegar solution (5%) and a soft bristled, non-abrasive brush may be used. Avoid contact with painted components and nearby surfaces. After cleaning, wipe down with a damp cloth and wipe dry to prevent spots.

Satin Stainless Steel

Care and Maintenance

Do not use or apply harsh chemicals, abrasives and/or cleaners. Product damage could occur.

Do not refurbish hardware. Contact a professional hardware restorer for refurbishing.

79173980

▶ Procedure is complete.

Remove existing latch receiver screws from latch receiver and dispose of properly. Position latch strike plate over latch receiver and fasten with color matched latch receiver screws (provided).

7

NOTICEFrenchwood® Patio Door latch strike plates differ for active doors versus active-passive/passive-active two panel doors. Follow procedure for your type of door.

▶ For passive hardware application for AP/PA doors: follow steps 3 - 7.

CAUTION

A-Series Frenchwood® Hinged Inswing and 400 Series Frenchwood Hinged Inswing Patio Doors Only

AP/PA Unit (Passive Panel)

Active Unit (Jamb)

Color MatchedLatch Receiver Screws (provided)

Color MatchedLatch Receiver Screws (provided)

Latch Receiver

Latch Strike Plate

Latch Receiver Screws

Latch ReceiverScrews

Latch Receiver

Latch Strike Plate