Traning Period in industry
-
Upload
prince-sharma -
Category
Documents
-
view
228 -
download
0
Transcript of Traning Period in industry
-
8/6/2019 Traning Period in industry
1/15
TRANING PERIOD INTRANING PERIOD IN
VISA DRUGS &VISA DRUGS &
PHARMACEUTICALS BADDI (HP)PHARMACEUTICALS BADDI (HP)
Presented by: Harwinder Kumar
Roll No. 81307421017
Address :-V.P.O Khera, pin code 146106,Dist Hoshiarpur.
Contacts - 01884242575, +919464065575.
Email Id:- [email protected]@hotmail.com
Collage:- RAYAT BAHRA INSTITUTE OF PHARMACY (Hoshiarpur, PUNJAB)Site:- http://home.rayatbahra.com/
-
8/6/2019 Traning Period in industry
2/15
CONTENTSCONTENTS--
y 1. TABLET SECTION
y 2. CAPSULE SECTION
y 3. PACKAGING SECTION
-
8/6/2019 Traning Period in industry
3/15
Instruments-
1. Paste kettle
2. RMG (Rapid Mixer Granulator)
3. FBD (Fluid Bed Dryer)
4. Vibro Sifter
5. Multimill
6. Blenders ( Double Cone Blender &octagonal blender)
7. Tablet Compression Machine
8. Tablet Coating Pan
-
8/6/2019 Traning Period in industry
4/15
-
8/6/2019 Traning Period in industry
5/15
-
8/6/2019 Traning Period in industry
6/15
Working of CompressionWorking of Compression MMachineachine
-
8/6/2019 Traning Period in industry
7/15
Problems during TabletProblems during Tablet CCompressionompression
y
CAPPING & LAMINATION-Capping
is defined as the splitting of one or both lidsof a tablet from its body. Lamination is similarto capping but here the tablet gets separatedinto layers.
y MOTTLING-Mottling is uneven distributionof the colour on the surface of the tablet,with dark and light patches on it.
y STICKING - It refers to the sticking of thetablet material with the die walls results inrough edges of tablet
y PICKING- Picking happens when a part ofthe tablets gets sticks to the punch surfaceand gets eroded from the tabletsurface.
-
8/6/2019 Traning Period in industry
8/15
Capsule Filling & sealing Machine
Capsule Polishing Machine
-
8/6/2019 Traning Period in industry
9/15
THE FIRSTSTATION:ORIENTATION OF
CAPSULE
The functions of first station
include capsule feeding,
aligning and insertion into boresof holding ring .
Also, vacuum is used for
separating capsule cap and body
in first station.
After orientation of capsule,capsule cap can stay in upper
holding ring and capsule body
can stay in lower holding ring.
-
8/6/2019 Traning Period in industry
10/15
Separate the holding ring , put the lower (body) holding
ring on the rotary table, pull the powder hopper over the
lower (body) holding ring, then auger inside powder
hopper starts to run and fill powder into the capsule body.
While Iower holding ring turns one circle, push powderhopper to its original position.
-
8/6/2019 Traning Period in industry
11/15
Put upper holding ring and lower holding ring together,
then take the holding ring ahead of ejector and aim
ejector at the bores of holding ring . Use hydraulic cylinder
to push ejector and let it press capsules for closing. Finally
push capsules inside the bores of holding ring out, thefinished capsules will be collected into the container.
-
8/6/2019 Traning Period in industry
12/15
LOCKING If the empty shell capsules arelocked then they will not open into the holding
rings and powder filling does not occurs.
Denting Denting of cap or body is occur during
locking when locking is not properly occurred(due to increase in hydraulic pressure during
locking).
-
8/6/2019 Traning Period in industry
13/15
In this packing one side of tablet stripes is PVC (Poly vinyl
Chloride) and another side is alumininum foil is used.
1.PVC FOILS- 1. PVC (Poly vinyl Chloride) foil 2.
PVDC(poly vinyl dichloride foil) foil.
Thickness of PVC foil 0.250mm.
2. ALUMINIUM FOIL
Thickness of aluminum foil 0.075mm.
-
8/6/2019 Traning Period in industry
14/15
In which both side of tablet/capsule strips aluminium foil
is used.
Thickness of alu. Foil - 0.020mm to 0.045mm
-
8/6/2019 Traning Period in industry
15/15