Trailer Axles and Components - Standen's

6
ISO 9001 CERTIFIED Genuine Standen’s Parts Distributor Genuine Replacement Parts 2,000 LB. Trailer Axles and Components Top Quality Trailer Axles & Components

Transcript of Trailer Axles and Components - Standen's

Page 1: Trailer Axles and Components - Standen's

ISO 9001CERTIFIED

GenuineStanden’s Parts

Distributor

Genuine Replacement Parts

2,000 LB.

Trailer Axlesand Components

Top Quality Trailer Axles & Components

Page 2: Trailer Axles and Components - Standen's

How to Measure an Axle

There are many ways to measure the length of an axle beam. The most accurate way to measure would be → hub-face-to-hub-face and spring-center-to-spring-center lengths.

What is the hub face measurement? Hub face is the distance from outside of hub mounting face to outside of hub mounting face. The hub face is also known as the mounting surface where the wheel makes contact with the hub. (See straight axle reference diagram below)

The spring centers identify the position of the springs and mounting hardware, as well this should align with the mounting positions on the trailer frame rails.

Please note that the springs can be mounted above (overslung) or below (underslung) the axle. This will raise or lower the axle depending on the configuration.

Alternatively - the flange face to flange face measurement can be provided which is measured from the outside of one brake flange to the outside of the opposite one (Where the brakes bolt on) as you see below.

This length may be easy to obtain if you are replacing an axle, but it’s important to note that this measurement is not the preferred method for determining which axle will best fit your trailer.

Hub face & spring center measurements are required before any order will be built.

www.standens.com

Axle Division Return Policy

AXLES CAN NOT BE RETURNED SPECIAL ORDER PARTS CAN NOT BE RETURNED RETURNS ARE NOT ACCEPTED AFTER 30 DAYS OF PURCHASE DATE There is no restocking fee associated with parts returned within 10 DAYS OF PURCHASE however parts returned after 10 days are subject to a 20% restocking fee. A COPY OF THE ORIGINAL INVOICE MUST ACCOMPANY ALL RETURNS ALL RETURNS MUST BE PREVIOUSLY APPROVED WITH AN RGA NO. PARTS MUST BE RETURNED FREIGHT PREPAID

Standen’s Warranty

IMT Standen’s Limited Partnership warrants Axle products manufactured or supplied by us to be free from defects in ma-terial and workmanship under normal use and service for a period of one year from date of manufacture of the product.

We will repair or replace without charge, shipping included, or at our option give credit for components shown to be out of specifications or defective.

This replacement warranty is limited to parts only and does not include any labour chargers, down time costs or conse-quential costs due to the defective product.

The warranty on our product is void when:1. Axle capacity is exceeded.2. The brakes are not adjusted before the trailer is put into use.3. Products are not installed according to factory recommendations and maintained. 4. Proper maintenance is not carried out. 5. Our products are altered or changed from original factory specifications without our knowledge and consent. 6. Damage occurs due to destructive driving or road conditions. 7. The product sits idle longer than 3 months and is not pre-serviced before being out into service.

This limited Warranty applies to the first use purchaser of the product only.

This limited Warranty is the only Warranty offered by us and therefore no employees, agent, salesperson or other person has the authority to offer or make any other Warranty.

Page 3: Trailer Axles and Components - Standen's

www.standens.com

7 X 1 1/4” Electric Brake

2 & 4

3

5

678

9 & 10

1415

12-70912-71071-361

71-45

47-114-0147-115-0146-030-0027-005-00

71-57

71-323

46-007-0046-114-00

111111111121111111112

Item Part # Qty/Brk Description

LH Complete Brake AssemblyRH Complete Brake AssemblySpring Kit containing:#046-023-00 Shoe Hold Down Spring#046-024-00 Retractor SpringShoe & Lining Kit containing:#040-125-00 Primary S&L#040-049-00 Secondary S&LLH Actuating Lever ArmRH Actuating Level ArmAnchor Post ClipWire ClipMagnet Kit containing:#042-134-00 Magnet#046-121-00 Magnet Clip#046-086-00 Magnet SpringAdjusting Spring Kit#046-022-00 Adjusting Screw Spring#043-021-00 Adjusting ScrewPlugShoe Centering Spring

7 X 1 3/4” Hydraulic Brake

12

3A & 3B

456789

11121516

13-71113-712

N/AN/A

54-80-0354-80-04

N/AN/AN/AN/AN/A

71-466

46-12646-12743-2946-7

111412111111112421111

Item Part # Qty/Brk Description

LH Complete Brake AssemblyRH Complete Brake AssemblyBacking PlateMounting Stud - Press-inWheel Cylinder Assembly - LH - DexterWheel Cylinder Assembly - RH - DexterAnchor PostLock WasherCounter Sunk Cap ScrewHex NutSocket Head Cap ScrewShoe & Lining Kit - Dexter - containing #040-327-01 Primary S&L#040-328-01 Secondary S&L#046-006-00 Shoe Hold Down Spring#035-001-00 Shoe Hold Down Spring#049-014-00 Hold Down PinRetractor SpringAdjusting Screw SpringAdjuster Screw AssemblyAdjuster Slot Plug

Page 4: Trailer Axles and Components - Standen's

www.standens.com

Item

123456788A8B9

Part #60210-9L44649L44610L44610L44649821-3880-1DC-11DC-11A85-1841-5

DescriptionBearing Kit - 1 Hub10-9 Grease SealInner Bearing ConeInner Bearing CupOuter Bearing CupOuter Bearing ConeSpindle NutCotter Pin (not used with E-Z Lube)Grease CapGrease Cap E-Z LubeRubber Plug for E-Z LubeTang Washer for E-Z Lube

Item2524A

24B

27A

27B

26A

26B

Hubs Part #8-4419-441

9-441H

8-451

8-451-LD

9-451

9-451H

DescriptionPlain Hub - tappedHub & Drum - tappedfor use w/electric brakes onlyHub & Drum - tappedfor use w/hydraulic brakes onlyPlain Hub - tapped5 1/2” dia. flange for 8”Plain Hub -studded6 1/2” dia. flange for 12” & 13” wheelsHub & Drum - studdedfor use w/electric brakes onlyHub & Drum - studdedfor use w/hydraulic brakes only

Bolt Circle4 on 4.004 on 4.00

4 on 4.00

5 on 4.50

5 on 4.50

5 on 4.50

5 on 4.50

Standard Grease Lube Parts

Item2020nsns

Part #12-70912-71013-71113-712

DescriptionLH 7x1 1/4 ElectricRH 7x1 1/4 ElectricLH 7x1 3/4 Hydraulic Uni-servoRH 7x1 3/4 Hydraulic Uni-servo

Brakes

Itemnsns1113

Part #WB-30WB-40DE-04WN-2

Description1/2-20 Bolt - 90 Deg. Taper1/2-20 Bolt - 60 Deg. Taper1/2-20 Double Ended Wheel Stud1/2-20 Wheel Nut

Studs, Bolts & Wheel Nuts Part #5015-35015-45015-5

Capacity/Spring675 lbs.900 lbs.1000 lbs.

Double Eye Springs

Part #540-14540-9545-3801-1810-2

Capacity/SpringFront HangerRear Hanger EyeShackle Strap9/16 Shackle Bolt7/16 Flanged Lock Nut

Single Hanger KitsPart # 579-0

Part #540-2540-14543-0545-225801-1810-2

Capacity/SpringFront and Rear HangerCentre HangerEqualizerShackle Strap9/16 Shackle Bolt7/16 Flanged Lock Nut

Tandem Hanger KitsPart # 577-0

Some combinations of hangers and spring mounting may result in insufficient clearance

* Measurements will be dependent on spring used

2,000 LB. CAPACITYS-20 - BTR HUB GROUP

LEAF SPRING APPLICATION INFORMATIONDOUBLE EYE SPRING SUSPENSION

* 26

* 30 1/4* 30 1/4

* 32 1/2

Page 5: Trailer Axles and Components - Standen's

www.standens.com

LEAF SPRING APPLICATION INFORMATIONSLIPPER SPRING SUSPENSION

Part #BT25-6BT25-9BT25-15

Capacity/Spring500 lbs.750 lbs.1200 lbs.

Spring

Part #540-14540-15801-1810-2

DescriptionFront HangerRear Hanger Eye9/16 Shackle Bolt7/16 Flanged Lock Nut3/8 x 3 1/2 Bolt3/8 Lock Nut

Single Hanger KitsPart #580

Some combinations of hangers and spring mounting may result in insufficient bump clearance

Wheel & Tire AssembliesSee Attached page

2000

Wheels

Rim Size13 x 4 1/2JJ

Part #15-1345-5-1

Bolt Circle5 on 4.50

Offset Capacity & psi 0 1360@50

TypeEight Spoke

Wheel and Tire Assemblies

Rim Size8”8”8”8”12”12”13”13”

Part #24-480C8-424-480C8-524-570C8-424-570C8-524-530C12-424-530C12-525-17580C13-527-17580C13-55

Bolt Circle4 on 4.004 on 4.004 on 4.004 on 4.004 on 4.005 on 4.505 on 4.505 on 4.50

Offset Capacity & psi 0 760 @ 90psi0 760 @ 90psi0 910 @ 75psi0 910 @ 75psi0 1050 @ 80psi0 1050 @ 80psi0 1360 @ 50psi0 1360 @ 50psi

TypeConventionalConventionalConventionalConventionalConventionalConventionalSpokeAluminum

Load RangeCCCCCCCC

Page 6: Trailer Axles and Components - Standen's

NOTES

HEAD OFFICE & MAIN PLANT

1222 - 58th Avenue S.E.P.O. Box 67, Station “T”Calgary, AlbertaCanada T2H 2G7

Toll Free: 1-800-663-7800Phone: (403) 258-7800Fax: (403) 258-7897Toll Free Fax: 1-866-258-7897

www.standens.com

AXLE DIVISION

5760 - 11th Street SECalgary, ABCanada T2H 2G7Phone: (403) 258-7896Fax: (403) [email protected]

DISTRIBUTION CENTRES

EDMONTON18922 - 111 Avenue NWEdmonton, ABCanada T5S 0B6Phone: (780) 430-7130Fax: (780) 430-7037

VANCOUVERUnit B 19372 - 94 AvenueSurrey, BCCanada V4N 4E4Toll Free: 1-800-665-9633Phone: (604) 888-7287Fax: (604) 888-7260

LONGUEUIL430 rue Jean-NeveuLongueuil, QuebecCanada J4G 1N8Toll Free: 1-866-674-0855Phone: (450) 674-0855Fax: (866) 674-0938

DISTRIBUTION CENTRES

TORONTO1238 Aimco Blvd.Mississauga, Ont.Canada L4W 1B2Toll Free: 1-800-567-7800Phone: (905) 625-0341Fax: (905) 625-2551

RANCHO CUCAMONGA9881 - 6 Street, Suite 205Rancho Cucamonga, CAU.S.A. 91730-5700Phone: (909) 466-5655Fax: (909) 466-0060

INDIANA6450 English AvenueIndianapolis, INU.S.A. 46219Toll Free: 1-800-851-2254Phone: (317) 423-1471Fax: (317) 423-1925

SERVICE CENTRE

1222 - 58th Avenue S.E.P.O. Box 67, Station “T”Calgary, AlbertaCanada T2H 2G7Toll Free: 1-800-663-7800Phone: (403) 258-7800Fax: (403) 258-7897Toll Free Fax: 1-866-258-7897

CHINA PLANT

Standen`s L & H(Xuzhou) Co. Ltd.28 Jinshan RoadXuzhou Economic andDevelopment ZoneXuzhou, Jiangsu 221004Phone: 86-516-8798-7958Fax: 86-516-8798-7900

CONTACT NUMBERS