Tradition, quality, and expertise.

PRICE BOOK Effective May 1, 2021

Tradition, quality, and expertise.

2 May 1, 2021Price Book

TABLE OF CONTENTS

GENERAL

3-5 Condition of sale / Terms and Conditions

6 Lead times

FINISHES

7 Field paint instructions/Pre-finish paint

7 Woodgrain - PRIME ONLY

WEIGHTS

8 Door weights

9 Frame weights

10 Mullion weights

11 Stick weights

ORDER FORMS

12 Door order form

13 Frame order form

DOORS

14 CX Series: Standard

15 CX Series - 250° Temperature Rise Doors

16 ST Series - Steel Stiffened Doors

17 Embossed: Panel & Woodgrain Price List

18 BR Series - Bullet Resistant Door Only

19-21 Options

SPECIALTY DOORS

22 FEMA

23 Tornado Series - Options

24 STC

F SERIES FRAMES

25 Masonry Frames

26-30 Options

DRYWALL SERIES

31 Drywall Frames

32 RF Series Remodeling Frames

33 ADJ Series - Adjustable Frames

34 FF Series - Flush Frames

35-37 Options

STICK & MULLION

38 S Series - Stick

39-40 S Series - Stick Options

41 M Series - Mullion

42-43 M Series -Mullion Options

44 Cut & Notch

44 Welded + Glazing Bead

PARTS

45 Doors

46-47 Frames

3May 1, 2021Price Book

TERMS AND CONDITIONS Acceptance. The following Terms and Conditions of sale are applicable to all Quotations, Contract, Purchase Orders, Order Acknowledgement Forms, and sales of Seller’s services and products, and are the only applicable terms and conditions thereto, except for terms establishing prices, quantities, delivery schedules, terms of payment, invoicing, shipping instructions, and the identification of the products associated with each transaction. If any conflict exists between the Terms and Conditions and a Quotation, Purchase Order, Order Acknowledgment form, or sale, these Terms and Conditions shall prevail BY REQUESTING A QUOTATION OF ORDERING ANY PRODUCTS OR SERVICES FROM SELLER, BUYER AGREES TO ALL THE FOLLOWING TERMS AND CONDITIONS. If a written contract signed by both parties is in existence covering the sale of the goods and services, the terms and conditions of the contract shall control to the extent they are inconsistent with these Terms and Conditions.

1. Order Procedure. Buyer may or may not request the preparation of a Quotation prior to ordering any products or services from Seller. Buyer then shall place a Purchase Order with Seller. By placing a Purchase Order, Buyer makes an offer to purchase products or services from Seller pursuant to these Terms and Conditions. Seller, in its discretion, may accept or reject the Purchase Order. If Seller accepts the Purchase Order, Seller shall issue an Order Acknowledgement Form confirming Buyer’s order. No Purchase Order is binding on Seller unless accepted by Seller as provided in these Terms and Conditions.

2. Quotations. Buyer may or may not request the preparation of a Quotation prior to ordering any products or services from Seller. Buyer then shall place a Purchase Order with Seller. By placing a Purchase Order, Buyer makes an offer to purchase products or services from Seller pursuant to these Terms and Conditions. Seller, in its discretion, may accept or reject the Purchase Order. If Seller accepts the Purchase Order, Seller shall issue an Order Acknowledgement Form confirming Buyer’s order. No Purchase Order is binding on Seller unless accepted by Seller as provided in these Terms and Conditions

3. Site Requirements.

a) The Quotation is contingent upon all work being performed during normal business hours unless otherwise negotiated and a mutually agreeable schedule. The Quotation is calculated on one continuous installation engagement based on acceptable site conditions where other dependent scopes have completed preparation for proposed materials (i.e. electrical work, floor work, adjacent construction). When Buyer has given authorization for work to begin, no other scopes may impede Seller’s ability to complete installation in agreed upon area. Seller reserves the right to invoice for costs that are incurred due to unacceptable site conditions or delays by others resulting in additional installation visits.

b) Signed acceptance by Buyer of shop drawings and/or submittals shall be interpreted as acceptance that proposed scope is the correct interpretation of construction documents. Any field verification and/or work required by others as detailed in the submittal will be provided and coordinated by Buyer. Work shall not begin nor shall orders be placed for any projects until all shop drawings and submittals have been approved in writing by Buyer.

4. Warranty. For a period of twelve (12) months from the date of delivery, Seller warrants only that all products sold pursuant to a Quotation or Purchase Order will conform to the description in this Price Book and will be free from defects in workmanship and materials. Extended warranties are available for an additional cost. Seller is not responsible for defects or damages caused by wear and tear, consumable materials, vandalism, fires, storms, floods, acts of God, misuse, abuse or alteration by any company other than Seller. Seller further warrants that Buyer will receive good and valid title to the products. Any claim on account of nonconforming or defective products or for any other cause whatsoever shall conclusively be deemed waived by Buyer unless written notice thereof is given to Seller promptly after discovery but no later than sixty (60) days from date of shipment. Seller shall have the right either to replace or repair any nonconforming or defective products, to refund the purchase price upon return of the products, or to grant a reasonable allowance on account of such nonconformance or defect Seller’s liability and Buyer’s exclusive remedy for nonconforming or defective products shall be limited solely to replacement, repair, refund, or allowance as Seller may elect. Seller shall be given reasonable opportunity to investigate all claims and no materials shall be returned to Seller until after inspection and approval by Seller and receipt by Buyer of written shipping instructions from Seller. Buyer acknowledges and agrees that the remedies set forth in this paragraph are Buyer’s exclusive remedies for the delivery of nonconforming or defective products..

a) No credit will be provided for any work completed by others during warranty term.

b) Warranty work will be performed during normal business hours with our standard response times. Any warranty work taking place beyond normal business hours or with expedited response time may be billable.

c) Products repaired or replaced under the warranty are warranted only through the remainder of the original warranty period.

Disclaimer of Further Warranties. Except as set forth above, there is no warranty, representation, or condition of any kind, express or implied (including no warranty of merchantability or fitness of the products for any use contemplated by Buyer) concerning Seller’s products or services and none shall be implied by law.


5. Limitation of Liability and Remedies. Seller shall not be liable, and Buyer waives all claims against Seller for any incidental, consequential, or special damages, including without limitation, lost revenues and profits even if Seller has been advised of the possibility of such damages. Buyer’s exclusive remedy for any cause of action under these Terms and Conditions is a claim for damages and in no event will damages or any other recovery of any kind against Seller exceed the purchase price of the specific products or services as to which the claim is made. Seller will not be liable to Buyer for any loss, damage, or injury to persons or property resulting from the handling, storage, transportation, resale, or use of the products in manufacturing processes, or in combination with other substances, or otherwise.

6.Intellectual Property Indemnification. a) Seller agrees to defend, indemnify and hold Buyer harmless against any claims, costs, damages, liability and expenses resulting from actual or alleged patent, trademark, or copyright infringement, misappropriation of confidential information, or violation of any other intellectual property right, domestic or foreign, in the selling or use of any part or product that is owned by Seller and that pertains to the subject matter of a Quotation, Purchase Order, or sale of products or services (provided that the product is not modified in anyway by Buyer or any other party, and that the product is used in the manner intended by Seller). If a suit or claim results in any injunction or any other order that would prevent Seller from supplying any product falling under a Quotation, Purchase Order, or sale, or if the result of such a suit or claim would, in the reasonable opinion of Seller, otherwise cause Seller to be unable to supply such products, Seller shall have the right, at its option, if it so chooses, to do one or more of the following: (i) secure an appropriate license to permit Seller to continue supplying the products to Buyer; (ii) modify the relevant product so that it becomes non-infringing, provided that any modification does not cause any material change to the operation or performance of the product; or (iii) replace the relevant product with a non-infringing but practically equivalent product. (b) Buyer agrees to defend, indemnify, and hold Seller harmless against any claims, costs, damages, liability and expenses resulting from actual or alleged patent, trademark, or copyright infringement, misappropriation of confidential information, or violation of any other intellectual property right, domestic or foreign, in the making, using or selling of any product or using any process that is owned by Buyer or is designed or specified by Buyer and that pertains to the subject matter of a Quotation, Purchase Order, or sale.

7. Ownership of Inventions. All drawings, know-how, designs, confidential information, and the like disclosed to Buyer by Seller and all rights therein will remain the property of Seller. Buyer shall have no claim to, ownership interest in, no license to, or no rights to any information provided or communicated by Seller.

8.Lead Times. If applicable, lead times are based on standard requirements by factory to provide materials proposed. Ship dates will be provided as estimate only once order is placed with the factory. Adequate packaging will be provided for any normal shipping circumstance such that materials will be protected and labeled as required. Special packaging may be provided for an additional expense. Shipping will be cost effective unless expedited fees are accepted by Buyer. If materials are to be provided to job site or Buyer location, dormakaba will make an informed decision as to the best instruction to provide the shipping company. If materials are not required to have direct delivery, materials will be brought to branch for pickup by Buyer. All freight terms shall be FOB. Any claims for damage in transit or lost freight, receiving, and inspection of materials is the responsibility of Buyer. It is a requirement of Buyer to inspect and review all materials prior to accepting shipment.

9. Title/Risk of Loss. All products shall be shipped FOB Seller’s manufacturing facility to Buyer’s designated delivery location. Unless otherwise agreed by the parties, Seller shall select the method of and carrier for the products. Seller reserves the right to ship items in a single or in multiple shipments. Title and risk of loss to products ordered passes to Buyer upon delivery of the products to the freight carrier. Unless mutually agreed upon in writing, shipping dates are approximate and are based upon prompt receipt of all necessary information.

10. Prices. Quoted price is valid for 90 days. Seller reserve the right to revise quotations after the 90 days. All accepted Purchase Orders are subject to Seller’s price in effect at time of shipment. Buyer shall be responsible for any increase in freight rates or transportation charges occurring after Seller prepared the Order Acknowledgment Form. on the Order Acknowledgment Form. Buyer shall pay to Seller in addition to the purchase price the amount of all fees, duties, licenses, and all sales, use, privilege, occupation, excise, or other taxes, federal, state, local, or foreign which Seller is required to pay or collect in connection with products or services sold to Buyer.

11. Payments. Unless otherwise agreed in writing between the parties, all Seller’s invoices are payable within thirty (30) days of their date. Time is of the essence. Interest on past due amounts will be assessed at the rate of 1.5% per month (18% per annum), or the maximum allowable by law. Seller reserves the right to full payment upon completion of work unless credit is pre-established. For any work requiring materials purchase or scheduling, a 50% deposit is due at time of proposal acceptance. Twenty percent (20%) of the Quotation, Purchase Order value may be billed after job award. Joint check agreements may be requested at the discretion of Seller. If payment is outstanding for any one account, work may be stopped and outstanding orders cancelled until account is restored. Should Seller require the use of collection, attorney’s fees, or fees for insufficient funds, Buyer agrees that these funds will be repaid to Seller. Seller retains the right to file a lien against all or part of the property being improved. Seller reserves the right to add a 2.5% charge if invoice becomes delinquent beyond terms.


12. Cancellation. In the event a Buyer’s Purchase Order and the issuance of an Order Acceptance Form is cancelled, it will be subject to standard 20% restocking fees, cancellation fees, engineering fees, materials & freight costs incurred, and administrative fees. Standard cancellation is 20% of order as long as no materials have been ordered. Should Buyer release material orders, Buyer will be liable for that portion of the job and 20% of the remaining amount of work unperformed/unordered.

13. Storage. If applicable, Seller reserves the right to implement a storage fee if delivery is delayed after agreed upon date. Should project timeline require storage of materials, Seller reserves the right to bill for those materials at the time they have been received at a Seller location, Buyer location, or at job site. Certificate of insurance for stored materials can be provided to Buyer upon request. Signed acceptance by Buyer of shop drawings and/or submittals shall be interpreted as acceptance that proposed scope is the correct interpretation of construction documents. Any field verification and/or work required by others as detailed in the submittal will be provided and coordinated by Buyer.

14. Insolvency. Seller may, at any time or times, suspend performance of any order or require payment in cash, security, or other adequate assurance satisfactory to Seller when, in Seller’s opinion, the financial condition of Buyer or other grounds for insecurity, including the filing of a petition for bankruptcy, warrant such action.

15. Force Majeure. Seller shall not be liable for any delay in fulfilling any order due to (a) fires, floods, strikes, or other labor disputes, accidents to machinery, acts of sabotage, riots, precedence or priorities granted at the request or for the benefit, directly or indirectly, of the federal or any state government or any subdivision or agency thereof, delays in transportation or lack of transportation facilities, restrictions imposed by federal or state legislation or rules of regulations thereunder; or (b) any cause beyond the control of Seller.

16. Ownership of Equipment. Unless otherwise agreed in a writing, all material, equipment, facilities, and special tooling, which term includes but is not limited to jigs, dies, fixtures, molds, patterns, special taps, special gauges, special test equipment, and manufacturing aids and replacements thereof, used in the manufacture of the products covered by any order shall remain the property of Seller. Any material, tooling, and equipment furnished to Seller by Buyer shall be and remain the personal property of Buyer with the title to and right of possession remaining in Buyer.

17. Confidential Information.All information furnished or made available by Seller to Buyer in connection with a transaction shall be held in confidence by Buyer. Buyer agrees not to use such information or disclose such information to others without Seller’s prior written consent. The obligations of this paragraph does not apply to any information which (a) at the time of disclosure was, or thereafter becomes, generally available to the public by publication or otherwise through no breach by Buyer of any obligation herein,(b) Buyer can show by written records was in Buyer’s possession prior to disclosure by the disclosing party, (c) is legally made available to Buyer by or through a third party having no direct or indirect confidentiality obligation to Seller with respect to such information, (d) was independently developed by Buyer without use of any of Seller’s confidential information, or (e) is required to be disclosed pursuant to applicable law.

18. Waiver. No waiver by Seller of any of these Terms and Conditions shall be effective unless explicitly set forth in writing and signed by Seller. No failure to exercise, or delay in exercising, any rights, remedy, power, or privilege arising from these Terms and Conditions shall operate or be construed as a waiver thereof, nor shall any single or partial exercise of any right, remedy, power, or privilege hereunder preclude any other or further exercise thereof or the exercise of any other right, remedy, power or privilege.

19. Assignment. No assignment of any right or interest or delegation of any obligation or performance of Buyer under this order may be made without the prior written consent of Seller. Any attempted assignment or delegation will be wholly void and totally ineffective for all purposes.

20. Choice of Law. All sales, agreements for sale, offers to sell, proposals, acknowledgments and contracts of sale, including, but not limited to, Purchase Orders accepted by Seller, shall be considered a contract under the laws of the State of Delaware, and the rights and duties of all persons, and the construction and effect of all provisions hereof, shall be governed by and construed according to the laws of the State of Delaware.

21. Integration Clause. These Terms and Conditions constitute the entirety of terms and conditions, except as set forth in paragraph one, governing the sale and purchase of products and services sold by Seller. No modification of these Terms and Conditions shall be of any force or effect unless in writing and signed Seller and Buyer. Buyer may desire to utilize its own form of acknowledgment or acceptance of these Terms and Conditions. However, the use of any such form shall be for convenience only. No modification of these Terms and Conditions shall be affected by the acknowledgment or acceptance of purchase orders, shipping instruction forms, bills of lading or any other document containing terms or conditions at variance with or in addition to those set forth herein, all such varying or additional terms being hereby objected to and rejected by Seller and deemed to be waived by Buyer.


LEAD TIMES*If orders are received before noon CST, lead times begin that day. If orders are received after noon CST, lead times begin the following day.

TURBO (SAME DAY), 1, 3, 5, 7 & 10 DAY QUICK SHIP:

72 Hours:• The 72 HOUR ORDER FORM is a list of specific SKU's that cannot be modified without quickship adders or longer lead times

• Frames must be ordered in bundle quantity minimums. No minimum quantity on doors.

• Max 360 frame pieces per order. Max 120 doors per order.

• For larger orders please consult the factory

• For 72 Hour Order Form please see www.meskerdoor.com

10 Day Order Form• The 10 DAY ORDER FORM is a list of specific SKU's that cannot be modified without quickship adders or longer lead times

• For 10 Day Order Form please see www.meskerdoor.com

QUICK SHIP - HMX Service: Huntsville• Most 4 week orders can be expedited to 3,5,7, or 10 day quick ship. Contact customer service with questions and availability per project.

Consult Factory Website for Current lead times www.meskerdoor.com• Non stock CX, AX, ST, Embossed Doors (SP, P4, P2S, P2A, P1, NW, SPW) BR, F, DW, RF, ADJ, FF, S, & M Series

• Cut & notch elevations

• Tag & Bundled frames

• Hospital stops

• Lead Lined doors and frames

• Welded elevations

• Non stock welded frames

• Non stock embossed doors

• BR Series assemblies

• Wind Storm doors

Please contact your local ISR for Quickship quotes


FINISHES SURFACE PREPARATION AND PAINTING• Mesker Door's recommended guidelines for preparation and painting of doors and frames.

• Maintenance of Steel Doors and frames should be done in accordance with SDI 124-98Maintenance of Standard Steel Doors and Frames"

• Priming and painting of steel doors and frames should be done in accordance with SDI A250.8, sections 2.1.3, 2.1.4, and 2.1.5. We also recommend following ANSI A250 recommendations, including but not limited to A250.8.4.1-4.6, and appendix "B" listed below.

MESKER Wood Grain - only available in Primed or Raw Galv.

Appendix B

ANSI / SDI-A250.8-2014

AESTHETICSThe production of steel doors and frames relies on a variety of manufacturing processes including spot welding, projection welding, arc welding ground smooth, grinding, filling, etc. These processes may result in a show-through after application of finished paint. These characteristics are inherent in production and are not to be considered as manufacturing defects.

The show-through characteristics increase as the paint gloss increases. This standard recommends a maximum paint gloss rating of 20% reflectance, measured using a 6° glass meter, which should be suitable for most applications. Translucent paints may emphasize show=-through characteristics and their use in not recommended. The 20% reflectance is equivalent to a Master Painters Institute (MPI) gloss rating description of a traditional "eggshell-like" finish.


WEIGHTS - DOORS (approximate)

W: H: CX 20

CX 18

CX 16

CX 14

CXF 18

CXF 16

CXF 14

ST 16

20

68

51 63 85 89 93 107 117 130

24 50 72 97 102 107 113 134 142

26 52 75 101 107 115 131 144 146

28 66 81 108 114 120 137 150 168

210, 30 73 88 116 124 132 149 165 176

34 96 126 135 146 164 183 186

36 100 132 142 153 172 192 207

38 104 134 148 159 177 199 209

310, 40 112 147 159 173 193 217 222

20

70

56 66 87 94 97 109 122 132

24 63 75 99 107 110 124 138 144

26 66 80 105 113 116 131 145 150

28 70 84 111 119 125 141 157 171

210, 30 77 92 121 130 136 153 170 181

34 102 135 144 153 173 192 195

36 105 139 149 160 180 200 214

38 110 145 155 171 192 214 220

310, 40 118 155 167 189 211 237 230

20

72

68 88 97 99 110 124 133

24 77 100 109 114 127 143 145

26 82 108 117 120 135 150 153

28 86 112 122 130 145 163 172

210, 30 95 125 134 141 159 177 185

34 105 142 149 156 179 195 202

36 108 145 153 166 189 208 220

38 112 150 159 177 200 222 225

310, 40 122 161 173 193 217 242 236

20

80

76 100 108 111 125 139 148

24 86 113 122 126 142 158 161

26 91 120 129 133 150 167 168

28 96 127 135 143 162 179 191

210, 30 105 138 149 156 175 195 202

34 117 154 165 175 197 219 218

36 120 159 170 183 206 229 239

38 125 166 178 196 220 145 246

310, 40 134 177 190 216 241 270 257

20

90

145 156 183 206 199

24 145 156 183 206 199

26 145 156 183 206 199

28 154 162 199 218 226

210, 30 167 182 214 240 239

34 187 202 240 268 259

36 194 207 253 282 284

38 203 219 271 296 309

310, 40 216 231 296 331 306

26

100

150 161 188 211 204

28 159 167 204 223 231

210, 30 172 187 219 245 244

34 192 207 245 273 264

36 199 212 258 287 289

38 208 224 276 301 314

310, 40 221 236 301 336 311


WEIGHTS - FRAMES (approximate)

16GA 14GA 16GA 14GA 16GA 14GA 16GA 14GA

W: H: 3 & 3-3/4 4-3/4 & 5-3/4 6-3/4 7-3/4, 8-1/4 & 8-3/4

3 SIDED FRAMES

20 24 26 28 210 30

68

37.13 47.03 43.89 55.28 47.03 59.07 53.63 79.37

34 36 38 310 40 39.38 49.88 46.55 58.63 49.88 62.65 56.88 71.23

40 48 50 54 58 60 43.88 55.58 51.87 65.33 55.58 69.81 63.38 79.37

68 70 74 80 48.38 61.28 57.19 72.03 61.28 76.97 69.88 87.51

20 24 26 28 210 30

70

38.25 48.45 45.22 56.95 48.45 60.86 55.25 81.40

34 36 38 310 40 40.50 51.30 47.88 60.30 51.30 64.44 58.50 73.26

40 48 50 54 58 60 45.00 57.00 53.20 67.00 57.00 71.60 65.00 81.40

68 70 74 80 49.50 62.70 58.52 73.70 62.70 78.76 71.50 89.54

20 24 26 28 210 30

72

38.93 49.31 46.02 57.96 49.31 61.93 56.23 82.62

34 36 38 310 40 41.18 52.16 48.68 61.31 52.16 65.51 59.48 74.48

40 48 50 54 58 60 45.68 57.86 54.00 68.01 57.86 72.67 65.98 82.62

68 70 74 80 50.18 63.56 59.32 74.71 63.56 79.83 72.48 90.76

20 24 26 28 210 30

80

42.75 54.15 50.54 63.65 54.15 68.02 61.75 89.54

34 36 38 310 40 45.00 57.00 53.20 67.00 57.00 71.60 65.00 81.40

40 48 50 54 58 60 49.50 62.70 58.52 73.70 62.70 78.76 71.50 89.54

68 70 74 80 54.00 68.40 63.84 80.40 68.40 85.92 78.00 97.68

20 24 26 28 210 30

100

51.75 65.55 61.18 77.05 65.55 82.34 74.75 105.82

34 36 38 310 40 54.00 68.40 63.84 80.40 68.40 85.92 78.00 97.68

40 48 50 54 58 60 58.50 74.10 69.16 87.10 74.10 93.08 84.50 105.82

68 70 74 80 63.00 79.80 74.48 93.80 79.80 100.24 91.00 113.96

HEADERS

20 24 26 28 310 30 6.75 8.55 7.98 10.05 8.55 10.74 9.75 24.42

34 36 38 310 40 9.00 11.40 10.64 13.40 11.40 14.32 13.00 16.28

40 48 50 54 58 60 13.50 17.10 15.96 20.10 17.10 21.48 19.50 24.42

68 70 74 80 18.00 22.80 21.28 26.80 22.80 28.64 26.00 32.56

100 22.50 28.50 26.60 33.50 28.50 35.80 32.50 40.70

HINGE JAMBS

68 15.19 19.24 17.96 22.61 19.24 24.17 21.94 27.47

70 15.75 19.95 18.62 23.45 19.95 25.06 22.75 28.49

72 16.09 20.38 19.02 23.95 20.38 25.60 23.24 29.10

80 18.00 22.80 21.28 26.80 22.80 28.64 26.00 32.56

90 21.50 27.50 25.60 32.50 27.50 34.80 31.50 39.70

100 22.50 28.50 26.60 33.50 28.50 35.80 32.50 40.70

STRIKE JAMBS

68 15.19 19.24 17.96 22.61 19.24 24.17 21.94 27.47

70 15.75 19.95 18.62 23.45 19.95 25.06 22.75 28.49

72 16.09 20.38 19.02 23.95 20.38 25.60 23.24 29.10

80 18.00 22.80 21.28 26.80 22.80 28.64 26.00 32.56

90 21.50 27.50 25.60 32.50 27.50 34.80 31.50 39.70

100 22.50 28.50 26.60 33.50 28.50 35.80 32.50 40.70


WEIGHTS - MULLIONS (approximate)

16GA 16GA 16GA

Mullions: L: 4-3/4 & 5-3/4 6-3/4 7-3/4, 8-1/4 & 8-3/4

BLANK MULL1' 5.5 6.0 7.0

10' 7" 55.0 60.0 70.0

HINGE 68,70,721' 5.6 6.1 7.1

10' 7" 56.0 61.0 71.0

HINGE 76 & UP1' 5.6 6.1 7.1

10' 7" 56.0 61.0 71.0

STRIKE1' 5.6 6.1 7.1

10' 7" 56.0 61.0 71.0

DBL HINGE 68,70,721' 5.7 6.2 7.2

10' 7" 57.0 62.0 72.0

DBL HINGE 76 & UP1' 5.7 6.2 7.2

10' 7" 57.0 62.0 72.0

DBL STRIKE1' 5.6 6.1 7.1

10' 7" 56.0 61.0 71.0

HINGE & STRIKE 68,70,721' 57.0 62.0 72.0

10' 7" 77.0 82.0 92.0

HINGE & STRIKE 76 & UP1' 57.0 62.0 72.0

10' 7" 77.0 82.0 92.0

BLANK HDW SECTION1' 1.4 1.6 2.1

10' 7" 1 .0 16.0 21.0

HINGE HDW SECTION (<75)1' 1.4 1.6 2.1

10' 7" 14.0 16.0 21.0

STRIKE HDW SECTION1' 1.4 1.6 2.1

10' 7" 14.0 16.0 21.0

STOP SECTION1' 1.8 1.8 1.8

10' 7" 18.0 18.0 18.0

CORNER POST1' 5.5 6.0 7.0

10' 7" 55.0 60.0 70.0


WEIGHTS - STICK (approximate)

16GA 16GA 16GA 16GA

Stick: L: 3 & 3-3/4 4-3/4 & 5-3/4 6-3/4 7-3/4, 8-1/4 & 8-3/4

BLANK 2"1' 5.5 5.5 6.0 7.0

10' 7" 55.0 55.0 60.0 70.0

BLANK 4"1' 5.6 5.6 6.1 7.1

10' 7" 56.0 56.0 61.0 71.0

HINGE 68,70,721' 5.6 5.6 6.1 7.1

10' 7" 56.0 56.0 61.0 71.0

HINGE 710, 801' 5.6 5.6 6.1 7.1

10' 7" 56.0 56.0 61.0 71.0

STRIKE1' 5.7 5.7 6.2 7.2

10' 7" 57.0 57.0 62.0 72.0

CASED OPEN 2"1' 5.7 5.7 6.2 7.2

10' 7" 57.0 57.0 62.0 72.0

CASED OPEN 4"1' 5.6 5.6 6.1 7.1

10' 7" 56.0 56.0 61.0 71.0

HAT FILLER1' 57.0 57.0 62.0 72.0

10' 7" 77.0 77.0 82.0 92.0

CASED OPEN HAT1' 57.0 57.0 62.0 72.0

10' 7" 77.0 77.0 82.0 92.0

BASE PANEL 6"1' 1.4 1.4 1.6 2.1

10' 7" 14.0 14.0 16.0 21.0

BASE PANEL 8"1' 1.4 1.4 1.6 2.1

10' 7" 14.0 14.0 16.0 21.0

BASE PANEL 10"1' 1.4 1.4 1.6 2.1

10' 7" 14.0 14.0 16.0 21.0

BASE PANEL 12"1' 1.8 1.8 1.8 1.8

10' 7" 18.0 18.0 18.0 18.0

FLOOR ANCHOR1' 5.5 5.5 6.0 7.0

10' 7" 55.0 55.0 60.0 70.0

PANEL SPREADER1' 5.5 5.5 6.0 7.0

10' 7" 55.0 55.0 60.0 70.0

BASE ANCHOR1' 5.5 5.5 6.0 7.0

10' 7" 5.0 55.0 60.0 70.0

GLAZING BEAD 5/8 x 5/8 x 10'1' 5.5 5.5 6.0 7.0

10' 7" 55.0 55.0 60.0 70.0


ME

SK

ER

DO

OR

- O

RD

ER

FO

RM

: DO

OR

S

Ser

ies:

Co

re:

Ed

ge

Ste

am:

Fire

lab

el:

Top

Cha

nnel

:Fa

ce:

Hd

w. L

oca

tions

:H

ing

e S

tile:

Lock

Stil

e:

CX

= S

tand

ard

ST

= S

teel

Siff

ened

SP

= 6

Pan

elP

4 =

4 P

anel

P2S

= 2

Pnl

. Sq.

P2A

= 2

Pnl

. Arc

h.N

W =

Wd.

gra

inS

PW

, BR

, etc

.A

X =

Sea

mle

ss

- =

Pol

ysty

rene

H =

Hon

eyco

mb

U =

Ure

than

eF

= Fi

berb

oard

- =

Std

. edg

eN

VS =

NVS

/A

XS

= S

titch

+ pu

ttyB

V1 =

1 S

ide

bev

BV2

= 2

Sid

es b

ev

- =

Myl

arU

# =

UL

+ ra

ting

W#

= W

HI +

ratin

g

- =

Inve

rted

T =

Flus

h to

pX

= H

dw. P

rep

Clo

ser r

einf

. Is

defa

ult f

eatu

re

- =

No

cuto

uts

V =

Visi

on li

teN

= N

arro

w li

teG

= H

alf l

iteFG

= F

ull l

iteVP

= V

iew

erC

O =

Cut

out o

nly

- =

Mes

ker

SC

T =

Ste

elcr

aft

AM

W =

Am

wel

dC

EC =

Cec

oC

UR

= C

urrie

sP

NR

= P

ione

erD

NS

= D

ean

Ste

elZZ

Z =

Cus

tom

DD

= D

utch

- =

4.5"

Std

. Wt.

4H =

4.5

" H

vy. W

t.B

= B

lank

edg

eB

R =

Con

t. re

inf.

5 =

5" S

td. W

t.5H

= 5

" H

vy. W

t.4

Inch

= 4

" x

4"Th

e de

faul

t qty

of

hing

e pr

eps

will

be

assu

med

161

= 16

1, 2

3/4

” B

acks

et

161T

= 16

1, 2

3/4

”, w

/ cu

stom

thru

bol

ts

161

Turt

le =

Tur

tle p

rep,

2 3

/4”

back

set

MB

= 8

6 Ed

ge, n

o fa

ce p

reps

MB

+Tem

plat

e =

Sec

tiona

l trim

pre

p

RP

= R

im p

anic

rein

forc

emen

t

RP

+Tem

plat

e =

Rim

rein

f. w

/ fn

c ho

les

VR =

Ver

tical

Rod

Rei

nfor

cem

ent

PP

= M

ortis

e bo

x re

inf.,

no

hole

s S

ee ta

bs

for m

ore

prep

cod

es

Ste

el T

ype:

Thi

ckne

ss:

Thi

ckne

ss:

Bo

tto

m C

hann

el:

A=A

40Z=

A60

G90

= G

90

- =

1 3/

420

= 2

0 G

auge

- =

18 G

auge

16 =

16

Gau

ge14

= 1

4 G

auge

- =

Inve

rted

T =

Flus

h bo

ttom

X =

Hdw

. Pre

p (gla

ss b

y ot

hers

)

QTY

DOOR #

SERIES

WIDTH: NOMINAL

WIDTH: NET UNDERSIZE

HEIGHT: NOMINAL

UNDERCUT

CORE

STEEL TYPE

EDGE SEAM

THICKNESS

GAUGE

LOC

K S

TILE

HIN

GE

STI

LE

HDW. LOCATIONS

FAC

E

TOP CHANNEL

BOTTOM CHANNEL

FIRE LABEL

APPLY DOOR # (Y/N)

HANDING

NO

TES


ME

SK

ER

DO

OR

- O

RD

ER

FO

RM

: FR

AM

ES

Ser

ies:

Co

mp

one

nt:

Typ

e:S

teel

typ

e:E

nds/

corn

ers:

Wel

ded

/anc

hors

Hd

w. L

oca

tions

:H

dw

: see

tab

s fo

r m

ore

F =

mas

onry

DW

= d

ryw

all

RF

= re

mod

elin

gFF

= fl

ush

face

S =

stic

kM

= m

ullio

n

FH =

hea

der

HJ

= hi

nge

jam

bS

J =

strik

e ja

mb

BJ

= bl

ank

strik

eW

J =

win

dow

BS

= b

lank

stic

kB

M =

bla

nk m

ull

HS

= H

inge

stic

kH

M =

Hin

ge M

S/M

= S

trik

e S

or

M

DR

= u

nequ

al ra

b.ER

= e

qual

rab.

SR

= s

ingl

e ra

b.D

E =

dbl.

eggr

ess

CO

= c

ased

ope

nC

= c

omm

unic

atin

gR

F =

Rem

odel

ing

A =

CR

SZ

= A

60G

90 =

G90

Not

chM

iter

Face

wel

dFu

ll w

eld

1 =

tack

ed in

ZEE

's2

= P

&D

hol

e3

= P

&D

+Tub

e4

= A

EW h

ole

only

6 =

Adj

usta

ble

flr.

7 =

othe

r-

= no

ne

Loos

e an

chor

s or

dere

d se

pera

tely

- =

Mes

ker

SC

T =

Ste

elcr

aft

AM

W =

Am

wel

dC

EC =

Cec

oC

UR

= C

urrie

sP

NR

= P

ione

erD

NS

= D

ean

Ste

elZZ

Z =

Cus

tom

DD

= D

utch

U =

AS

AC

= T

Str

ike

DB

S =

dea

dbol

tR

L =

rolle

r lat

chR

PR

= ri

m re

inf.

VRR

= v

. rod

rein

f.FB

= fl

ush

bolt

RA

= re

g. a

rm c

lose

r rei

nf.

PA =

P. a

rm c

lose

r rei

nf.

BR

= c

ont.

hing

e re

inf.

H =

inte

rcon

nect

ed s

trik

eVR

M =

CVR

str

ike

ELS

= e

lect

ric s

trik

eEH

= e

lect

ric h

inge

4H =

4.5

" H

vy. W

t. hi

nges

5 =

5" h

inge

s5H

= 5

" H

vy. W

t. hi

nges

The

defa

ult q

ty o

f Std

. Wt.

4.5"

sq.

hin

ge p

reps

will

be

assu

med

with

out n

eedi

ng a

co

de

Face

:T

hick

ness

- =

2"W

4F =

4"

- =

1 3/

48

= 1

3/8

0 =

no p

ocke

t

QTY

DOOR #

SERIES

COMPONENT

DEPTH

DEPTH: FRACTION

SIZE: NOMINAL

FRAME TYPE

STEEL TYPE

THICKNESS

GAUGE

HD

W P

REP

S /

REI

NFO

RC

EMEN

TS

HDW. LOCATIONS

FACE

RETURNS

WELDED ANCHORS

ENDS / CORNERS

FIRE LABEL

APPLY DOOR # (Y/N)

HANDING

NO

TES


CX Series - Doors

20 GAUGE 18 GAUGE 16 GAUGE 14 GAUGE

W: H: SDI Level 1 SDI Level 2 SDI Level 3 SDI Level 4

STANDARD FEATURES: Square edge non handed

20, 24, 26

68

462 533 622 894

28 470 542 632 904

210, 30 479 550 652 924

34, 36 593 673 779 1051

38 615 691 816 1088

310, 40 637 714 840 1112

20, 24, 26

70

479 555 645 917

28 485 563 660 933

210, 30 503 572 673 946

34, 36 691 781 1054

38 714 816 1088

310, 40 738 846 1118

20, 24, 26

72

563 652 924

28 581 672 943

210, 30 596 691 963

34, 36 706 788 1060

38 732 816 1088

310, 40 755 848 1120

20, 24, 26

80

732 842 1075

28 745 861 1095

210, 30 755 879 1112

34, 36 777 920 1153

38 799 937 1170

310, 40 825 952 1185

20, 24, 26

90

977 1210

28 996 1230

210, 30 1014 1247

34, 36 1055 1288

38 1072 1305

310, 40 1087 1320

20, 24, 26

100

1112 1345

28 1131 1365

210, 30 1149 1382

34, 36 1190 1423

38 1207 1440

310, 40 1222 1455


CX SERIES - 250° TEMPERATURE RISE DOORS

18 GAUGE 16 GAUGE 14 GAUGE

W: H: CX Series Temp Rise CX Series Temp Rise CX Series Temp Rise


20, 24, 26

68

878 967 1239

28 887 977 1249

210, 30 895 997 1269

34, 36 1018 1124 1396

38 1036 1161 1433

310, 40 1059 1185 1457

20, 24, 26

70

900 990 1262

28 908 1005 1278

210, 30 917 1018 1291

34, 36 1036 1126 1399

38 1059 1161 1433

310, 40 1083 1191 1463

20, 24, 26

72

908 997 1269

28 926 1017 1288

210, 30 941 1036 1308

34, 36 1051 1133 1405

38 1077 1161 1433

310, 40 1100 1193 1465

20, 24, 26

80

1077 1187 1420

28 1090 1206 1440

210, 30 1100 1224 1457

34, 36 1122 1265 1498

38 1144 1282 1515

310, 40 1170 1297 1530

20, 24, 26

90

1322 1555

28 1341 1575

210, 30 1359 1592

34, 36 1400 1633

38 1417 1650

310, 40 1432 1665

20, 24, 26

100

1457 1690

28 1476 1710

210, 30 1494 1727

34, 36 1535 1768

38 1552 1785

310, 40 1567 1800


ST SERIES - STEEL STIFFENED DOORS

16 GAUGE 14 GAUGE

W: H: Steel Stiffened ST Series Steel Stiffened ST Series

STANDARD FEATURES: Square edge non handed, Stiffeners 6" CTC

20, 24, 26

68

751 1023

28 762 1034

210, 30 781 1054

34, 36 909 1181

38 946 1218

310, 40 969 1241

20, 24, 26

70

775 1047

28 790 1062

210, 30 803 1075

34, 36 911 1183

38 946 1218

310, 40 976 1248

20, 24, 26

72

781 1054

28 967 1239

210, 30 820 1092

34, 36 917 1190

38 946 1218

310, 40 978 1250

20, 24, 26

80

971 1205

28 991 1224

210, 30 1008 1241

34, 36 1049 1282

38 1066 1300

310, 40 1082 1315

20, 24, 26

90

1106 1340

28 1126 1359

210, 30 1143 1376

34, 36 1184 1417

38 1201 1435

310, 40 1217 1450

20, 24, 26

100

1241 1475

28 1261 1494

210, 30 1278 1511

34, 36 1319 1552

38 1336 1570

310, 40 1352 1585


EMBOSSED DOORS - PANEL AND WOODGRAIN

18 GAUGE 18 GAUGE 18 GAUGE 18 GAUGE 18 GAUGE 18 GAUGE 18 GAUGE

W: H: SP Series P4 Series P2S Series P2A Series P1 Series NW Series SPW Series


20, 24, 26

68

– – – – – 662 –

28 682 737 737 737 737 671 881

210, 30 690 745 745 745 745 679 889

34, 36 813 – – – – – –

38 – – – – – – –

310, 40 – – – – – – –

20, 24, 26

70

− − − − − 684 −

28 703 758 758 758 758 692 902

210, 30 712 767 767 767 767 701 911

34, 36 831 − − − − − −

38 − − − − − − −

310, 40 − − − − − − −

20, 24, 26

80

− − − − − − −

28 885 − − − − − −

210, 30 895 − 972 − − − −

34, 36 − − − − − − −

38 − − − − − − −

310, 40 − − − − − −

***Other panel options available for orders of 25 doors or more. Please consult with the factory for details.

SP Series P4 Series P2S Series P2A Series P1 Series NW Series SPW Series


BR SERIES - BULLET RESISTANT DOOR ONLY

14 GAUGE

W: H: FRAMES PRICED SEPERATELY "F" SERIES 12 GAGE FRAME WITH BR LABEL REQUIRED THIS PRICING IS DOOR ONLY IT DOES NOT INCLUDE FRAME

STANDARD FEATURES: Square edge non handed, Stiffeners 6" CTC

20, 24, 26

68

2515

28 2545

210, 30 2575

34, 36 2660

38 2692

310, 40 2712

20, 24, 26

70

2535

28 2565

210, 30 2598

34, 36 2683

38 2715

310, 40 2734

20, 24, 26

72

2545

28 2575

210, 30 2608

34, 36 2698

38 2730

310, 40 2749

20, 24, 26

80

2625

28 2665

210, 30 2716

34, 36 2818

38 2860

310, 40 2880

20, 24, 26

90

2845

28 2885

210, 30 2940

34, 36 3062

38 3112

310, 40 3168

20, 24, 26

100

3122

28 3185

210, 30 3230

34, 36 3452

38 3522

310, 40 3608


DOOR OPTIONS

Description Code List

DOOR SERIESStandard CX

DOOR THICKNESSDEFAULT = 1 3/4"

NON-STANDARD DOOR SIZES (for nominal sizes not listed on price chartSpecial width = add to price of next wider (4'0" max width) 21.00Standard = listed widths with 1/4" undersizing No ChargeSpecial height = add to price of next taller (10'0" max height) 21.00Standard = listed heights w/ 1/8" off top, 3/4" or 3/8" undercut) No Charge

SPECIAL HARDWARE LOCATIONSDEFAULT - Mesker locationsOther SDI locationsCustom lock height ZZZ 28.00Custom hinge locations ZZZ 28.00Special backset for lock 86.00

CORE OPTIONSDEFAULT = Polystyrene P No ChargeHigh Density Poly P3 68.00Urethane (not available in 20GA) U 228.00Honeycomb (non-insulated) Not available on EMB doors H 32.00

STEEL TYPESGalvannealed - A40 A No ChargeGalvannealed - A60 Z 38.00Galvanized - G90 G90 515.00

EDGE SEAM CONSTRUCTIONDEFAULT - SQUARE / NON HANDED, mechanically Interlocking (SDI Model 1)BEVELED / HANDED, lock stile, mechanically Interlocking (SDI Model 1) BVS 74.00BEVELED / HANDED, both stiles, mechanically Interlocking (SDI Model 1)***All inactive leafs of pairs will be manufactured as SQUARE EDGE

BV2 No Charge

Seamless - stitch weld & putty (SDI Model 2) (square edge) S 99.00AX Series- continuously welded HDP (SDI Model 2) (not available in 20GA)***AX Requires 6" min stile on cutouts

NVS 129.00

PUSH / PULLSREINFORCEMENT: surface mounted MBNPREP: flush cup pull, other than 2 1/8" hole Price per side 54.00

LOCKS / LATCHESPREP: 161, 2 3/4" backset, cylindrical 161 No ChargePREP: 161, 2 3/4", cylindrical, custom thru bolts 161TB 21.00PREP: turtle, 2 3/4", cylindrical, ANSI 115.18 161 TURTLE No ChargePREP: 161, 2 3/4", cylindrical, blank edge 161BE No ChargePREP: 161, 2 3/8", cylindrical -- No ChargeREINFORCEMENT: single dummy function PP No ChargePREP: 86 edge, no face holes - mortise 86E No ChargePREP: 86 edge, teardrop, mortise escutcheon, ANSI A115.1 86M No ChargePREP: 86 edge, w/ function holes - mortise Sectional 86E+ 54.00PREP: unit lock prep 154.00PREP: card lock prep 54.00

DOUBLE COMBO LOCKSPREP: interconnected series prep (5 1/2" or less center-to-center) 1C 118.00

DEADLOCKS

PREP: cylindrical deadlock prep (2 1/8" bore, default height = 48" center line to floor) CDL 30.00PREP: mortise deadlock prep MDL 132.00

ROLLER LATCHPREP: located at lock height, 2 1/4" x 1 1/8" Latch prep, no face holes -- No ChargePREP: located on top edge of door 52.00

RIM EXIT DEVICEREINFORCEMENT: exit only, plus reinforcement on hinge stile RPD 34.00PREP: exit only (reinforcement lock stile only) no reinforcement on hinge stile MBN No ChargePREP: basic trim, 2 1/8" hole, 2 3/4" backset, no reinforcement on hinge stile 161 BE No ChargePREP: custom trim, function holes & thru bolts 54.00


DOOR OPTIONS


SVR EXIT DEVICEREINFORCEMENT: head & floor on lock stile, mid rail on lock & hinge stile SVR 101.00PREP: basic trim, 2 1/8" hole, 2 3/4" backset no top, bottom or hinge side reinforcement C4BE No ChargePREP: custom trim, function holes & thru bolts 155.00

MORTISE EXIT DEVICEREINFORCEMENT: mortise panic MP 34.00REINFORCEMENT: mortise panic - vertical rod MPVR+ 300.00PREP: custom trim, function holes & thru bolts MP+ 54.00

CVR EXIT DEVICEREINFORCEMENT & PREP: concealed vertical rod CVR 300.00

ELECTRIFIED HARDWAREPREP: electric lock w/ raceway -- 140.00PREP: electric Strike Prep w/ raceway -- 140.00PREP: electric hinge prep -- 21.00PREP: electric power transfer (EPT) no raceway EPT 75.00PREP: door position switch (DPS) (hole only) DPS 18.00PREP: door position switch (DPS) (with tabs) DPS wTabs 43.00PREP: Raceway RW 108.00PREP: Add Cat5 Cable to any of the above CAT5 25.00

CLOSERS / HOLDERSDEFAULT = REINFORCEMENT: surface mounted closer (14" double sided) Standard CL, No ChargePREP: concealed overhead closer CONC 300.00REINFORCEMENT: surface mounted closer - full door width Full Width CL 32.00PREP: hold open arm - mortise in top of door HOAM 120.00REINFORCEMENT: hold open arm - surface mount HOAs 32.00

DOOR BOTTOMSPREP: automatic door bottom - mortised w/ activator hole (5/8" height or taller) 150.00PREP: automatic door bottom - mortised w/ activator hole (1/2" height or shorter) 21.00

INACTIVE LEAF WITH ASTRAGAL PREPSAttach flat astragal to outside of door screwed on FAS 75.00Attach blank Z astragal Z 170.00Attach blank Z astragal + flush bolts Z-FB 210.00Attach Z astragal + U strike ZA 150.00Attach Z astragal + F.B. & U strike ZFBA 210.00Attach flat astragal to outside of door welded on FAW 150.00

INACTIVE LEAF WITHOUT ASTRAGAL PREPSFlush bolts cutout only (for use w/ ZA purchases seperately - no tabs) FBC 64.00Flush bolts prep (door prep with tabs) FB 85.00Surface bolts reinforcement SBP 64.00Deadlock strike Minimum 5 1/2" CtoC DLS 43.00Open back strike OBS 50.00U strike (ASA) ASA 30.00

�� MAR 2014

��

�� MAR 2014

��

��

�� MAR 2014

��

�� MAR 2014

��

��


DOOR OPTIONS


CUTOUTS, LITE KITS & LOUVERS***Special glass thickness kits are by quote only***6" from stile minimumIntegral lites only on BR doors mo lite kits

Stitch cutout only STITCH 33.00Cutout only Channel required on FG doors use pricing below C.O. 44.00Cutout HALF LITE w/ channel CO+G/C 108.00Cutout FULL LITE w/ channel CO+FG/C 172.00Install lite, 1/4" pocket up to 150 SQ" V 192.00Install lite Up to 1020 SQ" L1 269.00Install lite Up to 2800SQ" Includes Channeling cutout L2 417.00Integral Lite 1/4" pocket up to 100 SQ" INTLTV 225.00Integral Lite 1/4" pocket up to 1020 SQ" INTLTG 290.00Intergral Lite 1/4" pocket up to 2800 SQ" INTLTFG 450.00Install bottom louver 24x12 Consult factory for additional sizes L 475.00Install fire rated bottom louver FIRE-L 1,600.00Install full louver FL 1,187.00

MISC CUTOUTSViewer prep VP 15.00Mail slot MS 30.00Monorail MONO 225.00

LABELED DOORSDEFAULT = mylar FM (if applicable) FM No ChargeUL label metal (UL-C / UL-US) (specify UL-C if needed) ULM 45.00WHI label metal WHIM 45.00UL label mylar (UL-C / UL-US) (specify UL-C if needed) ULMYL 22.00WHI label mylar WHIMYL 22.00UL supplemental smoke label SMOKE 22.00Hurricane label - FBC FBCMYL 45.00Hurricane label - Miami Dade MIAMYL 45.00Hurricane label - TDI TDMYL 45.00ICC500-2014 Tornado Commercial (FEMA 361) ICCCOM 45.00ICC500-2014 3 deadlock (FEMA 320) ICC3DL 45.00E330 E330MYL 22.00Construction Label UL CONST 22.00

HINGE REINFORCEMENTSDEFAULT - 4 1/2" X 4 1/2" STD Wt. hinge - high frequency top hinge 4 No ChargeFor heavy weight - 4 1/2" X 4 1/2" hinges, use thinner Handing Plate option 4H No Charge5" hinges 5 15.005" heavy weight hinges 5H 15.004" hinges (blank for field tap) (offset needed) (no handing plates available) 4 INCH 62.006" hinges (blank for field tap) (offset needed) (no handing plates available) 6 INCH 62.00Anchor hinge prep AH 587.00Double mortise hinge 1 1/2PR DM 323.00Extra hinge Xtra Hinge 30.00Invisible hinge prep 3ea hinge Soss drilled and tapped other reinforce for field drill and tap O 300.00Invisible hinge prep 4ea hinge Soss drilled and tapped other reinforce for field drill and tap 400.00

CONTINUOUS HINGE (verify net width needed)Blank hinge style (does not include undersizing) B No ChargeReinforcement for fully mortised continuous hinge (does not include undersizing) BR 53.00

PIVOTSTop & bottom pivot Field Drill and Tap P2-TB 360.00Top & bottom & interm. pivot Field Drill and Tap P3-TIB 540.00

DUTCH DOOR PREPS - (not available in 20ga)Dutch DD 475.00Dutch shelf - 8" one side 345.00Dutch shelf - 6" both sides 425.00

TOP & BOTTOM CHANNELDEFAULT - inverted No ChargeFlush top Flush Top No ChargeTop caps, see door parts See Door PartsTop channel w/ putty & sealed Sealed Top 75.00Top rail rabbet Rabbet Top 700.00


FEMA

W: H:FEMA ICC−500−2014

Priced for door & frame, no hardwareRESIDENTIAL UNIT PREPED FOR 3 DL

FEMA ICC 500 2014 COMMERCIALPriced for door & frame, no hardware

PREPED FOR SECURITECH HARDWARE

STANDARD FEATURES: (price includes welded frame up to 8−3/4 but no hardware)

20, 24, 26

68

1310 −

28 1320 −

30 1340 4700

34, 36 − 5070

38 − 5070

310, 40 − 5070

20, 24, 26

70

1343 −

28 1359 −

30 1372 4700

34, 36 − 5070

38 − 5070

310, 40 − 5070

30

80

− 5070

34, 36 − 5070

38 − 5070

310, 40 − 5070

6068

− 8580

70, 80 − 9660

60, 7070

− 8580

80 − 9660

60, 7080

− 9660

80 − 9660

Please review listing for requirements before ordering Tornado Doors


TORNADO SERIES - OPTIONS


DOOR SERIESICC-500 ICC500

DOOR THICKNESSDEFAULT = 1 3/4" 4 No Charge

NON-STANDARD DOOR SIZES (for nominal sizes not listed on price chart)Special width = add to price of next wider 21.00Special height = add to price of next taller 21.00

CORE OPTIONSDEFAULT = High Density Polystyrene with Steel Stiffeners as require per listing. HDP No Charge

STEEL TYPESGalvannealed - A40 A No ChargeGalvannealed - A60 Z 38.00

EDGE SEAM CONSTRUCTION NVS already inlcuded in price of FEMA 320DEFAULT - SQUARE / NON HANDED No ChargeDEFAULT - continuously welded (SDI Model 2) No Charge

LOCKS / LATCHESFEMA 320 PREP: 161, 2 3/4" backset, cylindrical & 3 deadbolt preps FEMA(3)CDL No Charge

RIM EXIT DEVICEFEMA 361 PREP: Securitech 2 or 3 point locking No Charge

CLOSERS / HOLDERSREINFORCEMENT: surface mounted closer frame door comes with Closer reinforcing std. 17.00

DOOR BOTTOMSDEFAULT = REINFORCEMENT: door sweep - surface mounted - - No ChargeREINFORCEMENT: automatic door bottom - surface mounted No Charge

HINGE REINFORCEMENTS HW reccomended 5" HW recomended on CommercialDefault - heavy weight - 4 1/2" X 4 1/2" hinges, Not Recommended on Commercial door 4H 05" hinges optional 5 15.00Recommended 5" heavy weight hinge 5H 15.00

CONTINUOUS HINGE (verify net width needed)REINFORCEMENT: Must use Stainless Steel Screws with Design Hardware hinge BR 55.00

TOP & BOTTOM CHANNFlush bottom channel Flush Bottom No Charge


STC

STC

DOOR & FRAME ASSEMBLY - STC 43 - Specify 4.5"/5"/Cont

DOOR & FRAME ASSEMBLY - STC 45 - Specify 4.5"/5"/Cont

DOOR & FRAME ASSEMBLY - STC 48 PR - Includes cam lift hinges

DOOR & FRAME ASSEMBLY - STC 50 - Includes cam lift hinges

DOOR & FRAME ASSEMBLY - STC 50E - Includes cam lift hinges

DOOR & FRAME ASSEMBLY - STC 50PR - Includes cam lift hinges

DOOR & FRAME ASSEMBLY - STC 51L - Includes cam lift hinges (available with lite kit adder)

DOOR & FRAME ASSEMBLY - STC 52 - Includes cam lift hinges

W: H: STC

BORROWED LITES - All glass is by others, glass will ultimatey controlthe STC value

Max Size: 88"x88". Depth up to 9". Includes loose stops, anchors, glazing.

STC52FW

STC53FW

STC54FW

Please contact your Customer Service ISR for STC pricing.


F SERIES - MASONRY FRAMES

Standard Depths Custom Depths

W: H: 3 & 3-3/4 4-3/4 & 5-3/4 6-3/4 7-3/4, 8-1/4

& 8-3/43-1/8 to

4-5/84-7/8 to

6-5/86-7/8 to

8-5/88-7/8 to 12-3/4

12-7/8 to 14-3/4

3 SIDED FRAMES (not welded) (anchors NOT included)

20 24 26 28 210 30

68

185 186 196 213 258 284 313 399 526

34 36 38 310 40 189 192 200 223 264 294 324 410 537

48 50 54 58 60 223 228 238 266 287 318 343 428 555

68 70 74 80 233 239 256 284 300 339 364 449 576

20 24 26 28 210 30

70

194 196 206 224 258 284 313 399 526

34 36 38 310 40 198 202 210 234 264 294 324 410 537

48 50 54 58 60 233 238 248 278 287 318 343 428 555

68 70 74 80 243 249 266 296 300 339 364 449 576

20 24 26 28 210 30

72

196 199 222 240 258 284 313 399 526

34 36 38 310 40 200 205 226 250 264 294 324 410 537

48 50 54 58 60 235 242 266 296 287 318 343 428 555

68 70 74 80 245 253 284 314 300 339 364 449 576

20 24 26 28 210 30

80

221 227 251 270 276 306 334 420 547

34 36 38 310 40 225 233 255 280 282 316 345 431 558

48 50 54 58 60 269 280 304 330 303 338 363 448 575

68 70 74 80 279 291 322 348 316 359 384 469 596

20 24 26 28 210 30

100

276 270 295 325 334 363 387 473 631

34 36 38 310 40 280 276 299 335 340 373 398 484 642

48 50 54 58 60 333 328 352 394 371 404 427 512 665

68 70 74 80 343 339 370 412 384 425 448 533 686

HEADERS

20 24 26 28 310 30 35 33 36 39 50 53 60 103 146

34 36 38 310 40 39 39 40 49 56 63 71 114 157

48 50 54 58 60 63 64 68 80 67 74 81 124 167

68 70 74 80 73 75 86 98 80 95 102 145 188

100 83 86 104 116 93 116 130 166 209

HINGE JAMBS (anchors NOT included)

68 80 82 85 93 110 122 131 152 194

70 85 87 90 99 110 122 131 152 194

72 86 89 99 108 110 122 131 152 194

80 103 108 118 125 118 132 141 162 204

90 119 120 130 141 135 149 157 178 227

100 135 132 142 157 152 165 173 194 249

STRIKE JAMBS (anchors NOT included)

68 70 71 75 81 98 109 122 144 186

70 74 76 80 86 98 109 122 144 186

72 75 77 87 93 98 109 122 144 186

80 83 86 97 106 108 121 133 155 197

90 95 96 107 118 120 133 144 166 217

100 106 105 117 129 132 145 154 176 236


F SERIES - OPTIONS


FRAME SERIESStandard / masonry F

COMPONENT TERMINOLOGYHeader FH FH No ChargeHinge jamb HJ HJ No ChargeStrike jamb - ASA strike SJ SJ No ChargeStrike jamb - blank, mute holes only BJ BJ No ChargeWindow jamb - tabs both ends (add price to equal header length) WJ 15

DOOR POCKETDEFAULT = 1 3/4" 4 No Charge1 3/8" 8 No Charge2 1/4" per component 2-1/4 30.00Custom size (per component) CUSTOM 30.00KERF 1 3/4" (per component) (max 90min fire) (cost includes weatherstrip) 4-KERF 62.00Bronze* colored gasket standard. Consult factory for other colors. No ChargeThermal broken (per component) (not fire rated) (cost includes weatherstrip) 4-THERM 80.00

NON-STANDARD FRAME SIZES (nominal)Special width = add to price of next wider (per header) 14.00Special height = add to price of next taller (per jamb leg) 14.00

SPECIAL HARDWARE LOCATIONSDEFAULT - Mesker locations No ChargeCustom lock height -- No Add for SDI member locations ZZZ 30.00Custom hinge locations -- No Add for SDI member locations ZZZ 30.00

SPECIAL FACES4" Header (Under 4' 1") W4F W4F 40.004" Header (4' 1" and larger) W4F W4F 51.00Custom face dimension (1" to 1 7/8") (single or double) (per component) 64.00Custom face dimension (2 1/8" to 3 7/8") (single or double) (per component) 75.00Custom face dimension (4 1/8" to 6") (single or double) (per component) 100.00Custom face dimension (6 1/8" to 12") (single or double) (per component) 150.00

GAUGE14 Gauge (per component) 14 17.0012 Gauge (per component) May be square end depending on manufacturing location must be welded 12 87.00

STEEL TYPESGalvannealed - A40 - (per component) A No ChargeGalvannealed - A60 - (per component) Z 7.00Galvanized - G90 (per component) G90 85.00

STRIKE PREPSDEFAULT = PREP: ASA strike, 4 7/8" – No ChargePREP: additional ASA strike 30.00PREP: T strike, 2 3/4" C 30.00PREP: Double lip strike / emergency rescue hardware DLS 156.00PREP: emergency stop for double lip strike E-STOP E-STOP 85.00PREP: Custom Strike Request quote from Factory CSP Per Quote

INTERCONNECTED LOCKSPREP: interconnected strike (Anything Less than 5 1/2" CtoC) HS 100.00

DEADLOCKSPREP: deadlock strike (default height = 48" ctr to floor) DL-STK 30.00PREP: mortise deadlock strike MDL-STK 45.00

ROLLER LATCHPREP: roller latch strike at lock height - (use ASA or T strike pricing) No ChargePREP: roller latch strike in header (each) 30.00PREP: Roller latch in Header other than ASA or T 67.00

RIM EXIT DEVICEREINFORCEMENT: rim strike in jamb RPD 17.00


F SERIES - OPTIONS


SVR EXIT DEVICEREINFORCEMENT: surface strike in header (per head) SVR 17.00

MORTISE EXIT DEVICEPREP: mortise strike (ASA 4 7/8") in jamb ASA No Charge

CVR EXIT DEVICEPREP: CVR strike (each) CVR 75.00

ELECTRIFIED HARDWAREPREP: electric strike prep junction box not included add per below if required ES 60.00PREP: electric hinge prep junction box not included add per below if required EH 22.00PREP: electric power transfer (EPT) junction box not included add per below if required EPT 67.00PREP: door position switch (DPS) (hole only) junction box not included add per below if required DPS1 21.00PREP: door position switch (DPS) (with tabs) junction box not included add per below if required DPS wTabs 43.00REINFORCEMENT: junction box J-BOX 30.00

CLOSERS / HOLDERSREINFORCEMENT: closer - face - (flat plate) RA 17.00REINFORCEMENT: closer - soffit - (flat plate) PA 17.00REINFORCEMENT: closer - face & soffit - (flat plate) RA/PA 34.00REINFORCEMENT: closer sleeve - full profile Sleeve 40.00REINFORCEMENT: closer sleeve - full width 60.00REINFORCEMENT: closer sleeve - full width 4’ and over 120.00PREP: concealed closer 391.00Concealed OHS 120.00REINFORCEMENT: hold open - rabbet (flat plate) PA 111.00

INACTIVE LEAF PREPSStandard flush bolt strike prep FB 51.00Surface bolt strike reinforcement VRR 17.00Auto flushbolt w/lip 62.00

LABELED FRAMES (UL-Canada now available by request)DEFAULT = embossed (if applicable) No ChargeMylar Fire rated UL / Intertek - single frame 25.00Mylar Fire rated UL / Intertek - double frame 50.00Metal Fire Rated UL / Intertek- single frame 30.00Metal Fire Rated UL / Intertek- double frame 60.00Hurricane label - FBC / Miami Dade / TDI 45.00Hurricane label - Miami Dade 45.00

HINGE REINFORCEMENTSDEFAULT - 4 1/2" X 4 1/2" standard weight hinge 4 No Charge4 1/2" X 4 1/2" heavy weight hinge 4H No Charge5" hinges (up to 7' 6") 5 15.005" hinges (over 7' 6") 5 20.005" Heavy weight hinges (up to 7' 6") 5H 15.005" Heavy weight hinges (over 7' 6") 5H 20.004" or 6" hinges (blank for field tap) 4or6" Blanks 62.003 1/2" hinges (only available on 1-3/8" frame) 3 No ChargeDouble mortise hinge 1 1/2PR DMH 335.00Reinforcement for double acting hinge (each hinge) D 40.00Extra hinge Extra 30.00High frequency hinge prep (SDI 111-H example B) HiFRQ 11.00Full depth hinge reinforcement -- consult factory for quote FDH No ChargeInvisible hinge prep- if Soss hinge holes drilled and tapped others field drill and tap 3 hinge 225.00Invisible hinge prep- if Soss hinge holes drilled and tapped others field drill and tap 4 hinge 300.00

CONTINUOUS HINGEReinforcement for full mortised continuous hinge BR 55.00Blank hinge jamb w/ no reinforcement B No Charge

PIVOTSPivot prep (each) field drill and tap PV# 201.00Pocket field drill and tap POCKET 21.00Anchor hinge prep (per frame) field drill and tap AH 604.00Eliason Reinf. (Single) field drill and tap Eli.R(S) 40.00Eliason Reinf. (Double) field drill and tap Eli.R(D) 80.00


F SERIES - OPTIONS


CASED OPEN FRAMES (use pricing for 2 blank jambs (BJ) + header) CO No ChargeDUTCH DOOR PREPS

Dutch door frame - Hinge jamb DD 31.00Dutch door frame - Strike jamb DD 15.00

EQUAL or SINGLE RABBET ADDER (depths under 4-5/8" are single rabbet only)Header ER/SR No ChargeHinge jamb or strike jamb ER/SR No Charge

COMMUNICATING PREPS ADDERHeader C No ChargeHinge jamb C 90.00Strike jamb C 30.00

DOUBLE EGRESS ADDERHeader DE 135.00Hinge jamb per component 2 hinge jambs DE 135.00

SPECIAL CONSTRUCTION ADDERSDrywall returns on KD frame (per component) DW 8.00Special returns (per component) 45.00Special returns, square ends 30.00Cap end frame -- Per end 66.00Pocket frame (per component) HM trim only does not include pocket structure POCKET 120.00

HOSPITAL STOPS***Alters lead times 75.004" & 45 Degree (per jamb) 75.006" & 45 Degree (per jamb) 75.008" & 45 Degree (per jamb) 75.004" & 90 Degree (per jamb) 75.006" & 90 Degree (per jamb) 75.008" & 90 Degree (per jamb) 75.00

TAGGINGTag - opening number is listed on component label (per component) No ChargeTag & bundle - components wrapped & labeled w/ door number (per frame) 21.00

WELDINGFace weld (per corner) 22.00Face weld (3 sided frame) 44.00Face & throat weld in (3 sided frame) up to 81/4 75.00Face and throat weld 3 sided frame over 8 1/4 96.00


F SERIES - OPTIONS

ANCHORS

Wire Anchor PFMWA MWA 2.00T 4 3/4 PFMT4 MTA 4.00T 5 3/4 PFMT5 MTA 4.00T 6 3/4 PFMT6 MTA 4.00T 7 3/4 PFMT7 MTA 4.00T 8 3/4 PFMT8 MTA 4.00T 5 3/4 - Double egress PFDE684 MTA 7.00

Universal 4 3/4 PFUA4 UNA 3.00Universal 5 3/4 PFUA5 UNA 3.00Universal 6 3/4 PFUA6 UNA 3.00Universal 7 1/4 PFUA725 UNA 3.00Universal 7 3/4 PFUA7 UNA 3.00Universal 8 1/4 PFUA825 UNA 3.00Universal 8 3/4 PFUA8 UNA 3.003/4" Hole - (per hole) (5 3/4 profile only) – – 2.00Tack in anchor (per anchor) (no hole) (price of anchor not included) – – 3.00Tack in anchor (per anchor) (with hole) (price of anchor included) – – 8.00

ZEE anchor – ZEE 3.00Tack in anchor (per anchor) (no hole) (price of anchor not included) – – 3.00

Punch & dimple (hole only, each) (not including anchor) 2.00Per jamb - punch & dimple + tube anchor installed (up to 7'6", 4 holes) 52.00Per jamb - punch & dimple + tube anchor installed (up to 9'2", 5 holes) 65.00Per jamb - punch & dimple + tube anchor installed (above 9'2", 6 holes) 78.00Additional hole - punch & dimple + tube anchor installed 13.00


F SERIES - OPTIONS

ANCHORS

Sill (standard / default feature) PSF# SA No ChargeReverse floor anchor (per component) – Rev. F.A. No ChargeAdjustable floor anchor (4 3/4 thru 8 3/4) PFAAF AAF 15.00Tack in anchor (per anchor) 3.00

Miscellaneous

Multi-Purpose Double Egress anchor (must be welded in) PFDE680 7.00


DW SERIES - DRYWALL FRAMES


W: H: 4-1/2, 5-5/8, 5-7/8

7-3/4 & 8-1/4

3-5/8 to 5-15/16

6 to 7-1/4

7-5/16 to 9-1/4

9-5/16 to 12-3/4

12-15-16 to 14-3/4

3 SIDED FRAMES (knocked down)

20 24 26 28 210 30

68

215 266 268 294 323 409 540

34 36 38 310 40 229 273 278 308 334 420 551

48 50 54 58 60 259 310 309 339 365 438 565

68 70 74 80 290 355 338 375 406 459 586

20 24 26 28 210 30

70

221 268 268 294 323 409 540

34 36 38 310 40 235 275 278 308 334 420 551

48 50 54 58 60 267 312 309 339 365 438 565

68 70 74 80 298 357 338 375 406 459 586

20 24 26 28 210 30

72

233 281 268 294 323 409 540

34 36 38 310 40 247 288 278 308 334 420 551

48 50 54 58 60 279 324 309 339 365 438 565

68 70 74 80 310 369 338 375 406 459 586

20 24 26 28 210 30

80

264 309 294 319 346 430 560

34 36 38 310 40 278 316 304 333 357 441 571

48 50 54 58 60 319 364 341 365 389 458 585

68 70 74 80 350 409 370 401 430 479 606

20 24 26 28 210 30

100

313 408 343 382 432 492 641

34 36 38 310 40 327 415 353 396 443 503 652

48 50 54 58 60 367 458 391 439 489 540 675

68 70 74 80 398 503 420 475 530 561 696

HEADERS

20 24 26 28 210 30 43 57 52 55 62 105 148

34 36 38 310 40 57 64 62 69 73 116 159

48 50 54 58 60 73 84 81 87 95 126 169

68 70 74 80 104 129 110 123 136 147 190

100 135 170 142 155 168 181 211

HINGE JAMBS

68 93 113 114 126 135 156 198

70 97 114 114 126 135 156 198

72 103 120 114 126 135 156 198

80 123 140 130 139 147 166 208

90 135 164 143 158 172 182 231

100 147 187 155 176 197 207 253

STRIKE JAMBS

68 79 96 102 113 126 148 194

70 81 97 102 113 126 148 194

72 87 104 102 113 126 148 194

80 98 112 112 125 137 159 204

90 111 138 124 137 148 170 221

100 123 164 136 151 173 180 240


RF SERIES - REMODELING FRAMES

Standard Depths

W: H:2-1/4 Trim

Wall = 3-1/4 < > 4-1/8)

3-1/4 TrimWall =

(4-1/4 < > 5-1/8)

4-1/4 TrimWall =

(5-1/4 < > 6-1/8)

5-1/4 TrimWall =

(6-1/4 < > 7-1/8)

7-1/4 TrimWall =

(8-1/4 < > 9-1/8)

6 PIECE FRAMES (knocked down)

20 24 26 28 210 30

68

278 280 295 321 599

34 36 38 310 40 284 289 301 336 615

48 50 54 58 60 335 342 358 400 642

68 70 74 80 350 359 385 427 674

20 24 26 28 210 30

70

292 295 309 337 599

34 36 38 310 40 298 304 315 352 615

48 50 54 58 60 351 358 372 418 642

68 70 74 80 366 375 399 445 674

20 24 26 28 210 30

72

295 300 334 361 599

34 36 38 310 40 301 309 340 376 615

48 50 54 58 60 353 364 400 444 642

68 70 74 80 368 381 427 471 674

20 24 26 28 210 30

80

333 341 377 406 631

34 36 38 310 40 339 350 383 421 647

48 50 54 58 60 405 420 456 496 672

68 70 74 80 420 437 483 523 704

20 24 26 28 210 30

100

415 406 443 489 710

34 36 38 310 40 421 415 449 504 726

48 50 54 58 60 501 492 528 592 768

68 70 74 80 516 509 555 619 800

HEADERS

20 24 26 28 310 30 53 50 54 59 155

34 36 38 310 40 59 59 60 74 171

48 50 54 58 60 95 96 102 120 186

68 70 74 80 110 113 129 147 218

HINGE JAMBS

68 120 123 128 140 228

70 128 131 135 149 228

72 129 134 149 162 228

80 155 162 177 188 243

90 179 180 198 212 267

100 203 198 213 236 291

STRIKE JAMBS

68 105 107 113 122 216

70 111 114 120 129 216

72 113 116 131 140 216

80 125 129 146 159 233

90 142 144 161 177 249

100 159 158 176 194 264


ADJ SERIES - ADJUSTABLE FRAMES

Adjustable Depths

W: H:8-3/4

Slides to wall thickness of: (4-5/8 < > 7-3/4)12-1/4

Slides to wall thickness of: (7-1/2 < > 11-1/4)

3 SIDED FRAMES (knocked down) (raw A60 steel)

20 24 26 28 210 30

68

445 475

34 36 38 310 40 485 515

48 50 54 58 60 545 575

68 70 74 80 575 605

20 24 26 28 210 30

70

465 495

34 36 38 310 40 505 535

48 50 54 58 60 565 595

68 70 74 80 595 625

20 24 26 28 210 30

72

475 505

34 36 38 310 40 515 545

48 50 54 58 60 575 605

68 70 74 80 605 635

20 24 26 28 210 30

80

495 525

34 36 38 310 40 535 565

48 50 54 58 60 595 625

68 70 74 80 625 655

20 24 26 28 210 30

100

605 635

34 36 38 310 40 645 675

48 50 54 58 60 715 745

68 70 74 80 745 775

HEADERS

20 24 26 28 310 30 85 95

34 36 38 310 40 125 135

48 50 54 58 60 155 165

68 70 74 80 185 195

HINGE JAMBS

68 195 205

70 205 215

72 210 220

80 220 230

90 260 270

100 280 290

STRIKE JAMBS

68 165 175

70 175 185

72 180 190

80 190 200

90 210 220

100 240 250


FF SERIES - FLUSH FRAMES Jamb depth = wall size + 1/8"


W: H:3 1/83 5/83 7/8

4-3/4 &5 5-3/8 & 6-3/8

6-7/8, 7-3/8, 7-7/8

3-1/4 to

4-7/8

5-1/8 to 6-3/4 7 to 8-7/8 9 to 12

3 SIDED FRAMES (knocked down)

20 24 26 28 210 30

68

185 183 186 196 213 258 284 313

34 36 38 310 40 189 189 192 200 223 264 294 324

48 50 54 58 60 223 223 228 238 266 287 318 343

68 70 74 80 233 233 239 256 284 300 339 364

20 24 26 28 210 30

70

194 192 196 206 224 258 284 313

34 36 38 310 40 198 198 202 210 234 264 294 324

48 50 54 58 60 233 233 238 248 278 287 318 343

68 70 74 80 243 243 249 266 296 300 339 364

20 24 26 28 210 30

72

196 194 199 222 240 258 284 313

34 36 38 310 40 200 200 205 226 250 264 294 324

48 50 54 58 60 235 235 242 266 296 287 318 343

68 70 74 80 245 245 253 284 314 300 339 364

20 24 26 28 210 30

80

221 219 227 251 270 276 306 334

34 36 38 310 40 225 225 233 255 280 282 316 345

48 50 54 58 60 269 269 280 304 330 303 338 363

68 70 74 80 279 279 291 322 348 316 359 384

20 24 26 28 210 30

100

276 274 270 295 325 334 363 387

34 36 38 310 40 280 280 276 299 335 340 373 398

48 50 54 58 60 333 333 328 352 394 371 404 427

68 70 74 80 343 343 339 370 412 384 425 448

HEADERS

20 24 26 28 310 30 35 33 33 36 39 50 53 60

34 36 38 310 40 39 39 39 40 49 56 63 71

48 50 54 58 60 63 63 64 68 80 67 74 81

68 70 74 80 73 73 75 86 98 80 95 102

100 83 83 86 104 116 93 116 130

HINGE JAMBS

68 80 80 82 85 93 110 122 131

70 85 85 87 90 99 110 122 131

72 86 86 89 99 108 110 122 131

80 103 103 108 118 125 118 132 141

90 119 119 120 130 141 135 149 157

100 135 135 132 142 157 152 165 173

STRIKE JAMBS

68 70 70 71 75 81 98 109 122

70 74 74 76 80 86 98 109 122

72 75 75 77 87 93 98 109 122

80 83 83 86 97 106 108 121 133

90 95 95 96 107 118 120 133 144

100 106 106 105 117 129 132 145 154


DW,RF,ADJ,FF SERIES - OPTIONS


FRAME SERIESDrywall FDJ

COMPONENT TERMINOLOGYHeader FH FH No ChargeHinge jamb HJ HJ No ChargeStrike jamb - ASA strike SJ SJ No ChargeStrike jamb - blank, mute holes only BJ BJ No ChargeWindow jamb - tabs both ends (add price to equal header length) WJ 31.00

DOOR POCKETDEFAULT = 1 3/4" 4 No Charge1 3/8" 8 No Charge2 1/4" (per component) 2-1/4 30.00Custom size (per component) CUSTOM 30.00KERF 1 3/4" (per component) (max 90min fire) (cost includes weatherstrip) 4-KERF 62.00Bronze* colored gasket standard. Consult factory for other colors. No Charge

NON-STANDARD FRAME SIZES (nominal)Special width = add to price of next wider (per header) 14.00Special height = add to price of next taller (per jamb leg) 14.00

SPECIAL HARDWARE LOCATIONSDEFAULT - Mesker locations No ChargeCustom lock height -- No Add for SDI member locations SLL 30.00Custom hinge locations -- No Add for SDI member locations SHL 30.00

SPECIAL FACESCustom face dimension (1" to 1 7/8") (single or double) (per component) 64.00Custom face dimension (2 1/8" to 3 7/8") (single or double) (per component) 75.00

GAUGEDEFAULT = 16 Gauge Standard 16 No Charge14 Gauge (per component) 14 17.00

STEEL TYPESGalvannealed - A40 - (per component) Z No ChargeGalvannealed - A60 - (per component) Z 7.00Galvanized - G90 (per component) G90 85.00

PUSH/PULL BJ No ChargeSTRIKES

DEFAULT = PREP: ASA strike, 4 7/8" - No ChargePREP: additional ASA strike US 30.00PREP: T strike, 2 3/4" C 30 C 30.00PREP: Double lip strike / emergency rescue hardware (ERH) DLS(ERH) 156.00PREP: emergency stop for double lip strike E-STOP 85.00PREP: Custom Strike CONSULT FACTORY FOR QUOTE CSP No Charge

INTERCONNECTED LOCKSPREP: interconnected strike (Anything Less than 5 1/2" CtoC) HS 100.00

DEADLOCKSPREP: deadlock strike (default height = 48" ctr to floor) DBS 30.00PREP: mortise deadlock strike MDBS 45.00

ROLLER LATCHPREP: roller latch strike at lock height - (use ASA or T strike pricing) - or C No ChargePREP: roller latch strike in header (each) RL 30.00PREP: Roller latch in Header other than ASA or T 67.00

RIM EXIT DEVICEREINFORCEMENT: rim strike in jamb RPR 17.00

SVR EXIT DEVICEREINFORCEMENT: surface strike in header (per head) VRR 17.00

MORTISE EXIT DEVICEPREP: mortise strike (ASA 4 7/8") in jamb U No Charge




CVR EXIT DEVICEPREP: CVR strike (each) VRM 75.00

ELECTRIFIED HARDWAREPREP: electric strike prep junction box not included add per below if required ES 60.00PREP: electric hinge prep junction box not included add per below if required EH 22.00PREP: electric power transfer (EPT) junction box not included add per below if required EPT 67.00PREP: door position switch (DPS) (hole only) junction box not included add per below if required DPS1 21.00PREP: door position switch (DPS) (with tabs) junction box not included add per below if required DPS2 43.00REINFORCEMENT: junction box JBOX 30.00

CLOSERS / HOLDERSREINFORCEMENT: closer - face - (flat plate) RA 17.00REINFORCEMENT: closer - soffit - (flat plate) PA 17.00REINFORCEMENT: closer - face & soffit - (flat plate) RA+PA 34.00REINFORCEMENT: closer sleeve - full profile Clr Sleeve 40.00REINFORCEMENT: closer sleeve - full width up to 3’11” RA+FullWidth 60.00REINFORCEMENT: closer sleeve - full width 4” and over 120.00PREP: concealed closer 391.00Concealed OHS 120.00REINFORCEMENT: hold open - rabbet (flat plate) PA 111.00

INACTIVE LEAF PREPSStandard flush bolt strike prep FB 51.00Surface bolt strike reinforcement VRR 17.00Auto flushbolt strike w/lip 62.00

LABELED FRAMES (UL-Canada now available by request)DEFAULT = embossed (if applicable) No ChargeMylar - single frame 25.00Mylar - double frame 50.00Metal - single frame 30.00Metal - double frame 60.00Hurricane label - (each) 45.00

HINGE REINFORCEMENTSDEFAULT - 4 1/2" X 4 1/2" standard weight hinge 4 No Charge4 1/2" X 4 1/2" heavy weight hinge 4H No Charge5" hinges (up to 7' 6") 5 15.005" hinges (over 7' 6") 5 20.005" Heavy weight hinges (up to 7' 6") 5H 15.005" Heavy weight hinges (over 7' 6") 5H 20.004" or 6" hinges (blank for field tap) 4or6" Blanks 62.003 1/2" hinges (only available on 1-3/8" frame) 3 No ChargeDouble mortise hinge 1 1/2PR DMH 335.00Reinforcement for double acting hinge (each hinge) D 40.00Extra hinge Extra 30.00High frequency hinge prep (SDI 111-H example B) per hinge HiFRQ 11.00Full depth hinge reinforcement -- consult factory for quote FDH No ChargeInvisible hinge prep- if Soss hinge holes drilled and tapped others field drill and tap 3 hinge O 225.00Invisible hinge prep- if Soss hinge holes drilled and tapped others field drill and tap 3 hinge O 300.00

CONTINUOUS HINGEReinforcement for full mortised continuous hinge BR 55.00Blank hinge jamb w/ no reinforcement B No Charge

PIVOTSPivot prep (each) field drill and tap PV# 201.00Pocket field drill and tap POCKET 21.00Anchor hinge prep (per frame) field drill and tap AH 604.00Eliason Reinf. (Single) field drill and tap Eli.R(S) 40.00Eliason Reinf. (Double) field drill and tap Eli.R(D) 80.00

CASED OPEN FRAMES (use pricing for 2 blank jambs (BJ) + header) CO No ChargeDUTCH DOOR PREPS

Dutch door frame - Hinge jamb DD 31.00Dutch door frame - Strike jamb DD 15.00




EQUAL or SINGLE RABBET ADDER (depths under 4-5/8" are single rabbet only)Header ER/SR No ChargeHinge jamb or strike jamb ER/SR No Charge

COMMUNICATING PREPS ADDERHeader C No ChargeHinge jamb C 60.00Strike jamb C 30.00

DOUBLE EGRESS ADDERHeader DE 135.00Hinge jamb (2 hinge jambs needed per frame) DE 135.00

SPECIAL CONSTRUCTION ADDERSSpecial returns (per component) 45.00

HOSPITAL STOPS***Alters lead times4" & 45 Degree (per jamb) 75.006" & 45 Degree (per jamb) 75.008" & 45 Degree (per jamb) 75.004" & 90 Degree (per jamb) 75.006" & 90 Degree (per jamb) 75.008" & 90 Degree (per jamb) 75.00

TAGGINGTag - opening number is listed on component label (per component) No ChargeTag & bundle - components wrapped & labeled w/ door number (per frame) 21.00

ANCHORS

Punch & dimple for screw (standard / default feature) No ChargeDrywall snap in anchor - no punch & dimple (2 needed per jamb) PFDSNA DSNA 1.00Installed compression anchor (standard / default feature) ***See Parts page for price on loose compression anchors PFDCA DCA No Charge

Tack in anchor (per anchor) (no hole) (price of anchor not included) – – 3.00

WELDING

Face weld (per corner) 22.00Face weld (3 sided frame) 44.00Face & throat weld (3 sided frame) up to 8-1/4 75.00Face & throat weld (3 sided frame) over 8-1/4 96.00


S SERIES - STICK


Stick: L: 3 & 3 3/4

4-3/4 & 5-3/4 6-3/4 7-3/4, 8-1/4,

8-3/43-1/8 to

4-5/84-7/8 to

6-5/86-7/8 to

8-5/88-7/8 to 12-3/4

12-7/8 to 14-3/4

BLANK 2"1' 14 14 15 16 16 18 21 28 34

10' 7" 111 104 113 141 134 163 184 245 315

BLANK 4"1' – 21 22 24 – 27 32 35 42

10' 7" – 180 194 218 – 244 284 323 393

HINGE 68,70,721' Per foot = (desired length in BLANK 2") + (qty of hinges x hinge prep charge)

10' 7" 201 194 203 183 184 253 274 355 405

HINGE 710, 801' Per foot = (desired length in BLANK 2") + (qty of hinges x hinge prep charge)

10' 7" 231 224 233 213 214 283 304 365 435

STRIKE1' Per foot = (desired length in BLANK 2") + (qty of hinges x hinge prep charge)

10' 7" 141 134 143 171 164 193 214 275 345

CASED OPEN 2"1' 14 14 15 17 16 18 23 28 34

10' 7" 111 104 113 141 134 163 184 245 315

CASED OPEN 4"1' – 21 22 24 – 27 32 35 42

10' 7" – 180 194 218 – 244 284 323 393

HAT FILLER1' 14 14 16 19 17 18 26 27 34

10' 7" 121 121 138 162 144 151 206 243 311

CASED OPEN HAT1' 13 13 14 17 15 16 24 26 33

10' 7" 102 102 120 150 124 131 193 229 300

BASE PANEL 6"1' – 22 24 30 – 28 34 40 49

10' 7" – 176 192 240 – 219 269 320 387

BASE PANEL 8"1' – 30 32 40 – 36 42 49 57

10' 7" – 240 256 320 – 286 336 387 454

BASE PANEL 10"1' – – 40 48 – – 51 57 66

10' 7" – – 320 384 – – 404 454 521

BASE PANEL 12"1' – – – 36 – – 59 66 74

10' 7" – – – 270 – – 471 521 588

FLOOR ANCHOR1' 15 15 20 22 19 19 30 32 39

10' 7" 127 127 174 197 151 158 242 286 356

PANEL SPREADER1' 15 15 20 22 19 19 30 32 39

10' 7" 127 127 174 197 151 158 242 286 356

BASE ANCHOR1' 15 15 20 22 19 19 30 32 39

10' 7" 127 127 174 197 151 158 242 286 356

GLAZING BEAD 5/8 x 5/8 x 10'1' 3 – – – – – – – –

10' 7" 32 – – – – – – – –


S SERIES - OPTIONS


FRAME SERIESStick S No Charge

COMPONENT TERMINOLOGYBlank stick 2" BS No ChargeBlank stick 4" BS4 No ChargeHinge stick HS No ChargeStrike stick SS No ChargeCased open stick 2" CS No ChargeHat HAT No ChargeHat - cased open HAC No ChargeBase panel 6" BP6 No ChargeFloor anchor AFL No ChargePanel spreader PSP No ChargeBase anchor ABP No Charge

DOOR POCKET

Special depth, (add to next larger size)1' 2 .00

10' 7" 20.00SPECIAL FACES

2" Face No Charge4" Face W4F No Charge

1"-3 15/16" Face (add to 2" face stick)1' W#F 7.00

10' 7" W#F 70.00

6" Face (add to 4" face stick)1' W6F 7.00

10' 7" W6F 70.00


10' 7" W8F 150.00


10' 7" W10F 230.00


10' 7" W12F 310.00GAUGE

DEFAULT = 16 Gauge 16 No Charge

14 Gauge1' 14 3.00

10' 7" 14 30.00STEEL TYPES

Galvannealed - A40 - (per component)1' Z No Charge

10' 7" Z No Charge

Galvannealed - A60 - (per component)1' Z 1.00

10' 7" Z 10.00

Galvanized - G90 (per component)1' G90 12.00

10' 7" G90 120.00LOCKS / LATCHES

DEFAULT = PREP: ASA strike, 4 7/8" or blank stick prep – 21.00PREP: additional ASA strike US 30.00PREP: T strike, 2 3/4" C 30.00PREP: Double lip strike / emergency rescue hardware (ERH) DLS(ERH) 156.00

INTERCONNECTED LOCKSPREP: interconnected strike (4" ctc) HS 71.00

DEADLOCKSPREP: deadlock strike (default height = 48" ctr to floor) DBS 55.00

ROLLER LATCHPREP: roller latch strike at lock height - (use ASA or T strike pricing) on strike stick - or C No ChargePREP: roller latch strike in header (each) RL 57.00


S SERIES - OPTIONS



SVR EXIT DEVICEREINFORCEMENT: surface strike in header (per head) VRR 17.00



ELECTRIFIED HARDWAREPREP: electric strike prep junction box not included add pe below if required ES 60.00PREP: electric hinge prep junction box not included add pe below if required EH 22.00PREP: electric power transfer (EPT) junction box not included add per below if required EPT 67.00PREP: door position switch (DPS) (hole only) junction box not included add pe below if required DPS1 21.00

PREP: door position switch (DPS) (with tabs) junction box not included add pe below if required DPS2 43.00

REINFORCEMENT: junction box JBOX 30.00CLOSERS / HOLDERS

REINFORCEMENT: closer - face - (flat plate) RA 17.00REINFORCEMENT: closer - soffit - (flat plate) PA 17.00REINFORCEMENT: closer - face & soffit - (flat plate) RA+PA 34.00

INACTIVE LEAF PREPSStandard flush bolt strike prep FB 51.00Surface bolt strike reinforcement VRR 17.00

HINGE REINFORCEMENTS (add to cost of Hinge Stick)DEFAULT - 4 1/2" X 4 1/2" standard weight hinge 4 No Charge4 1/2" X 4 1/2" heavy weight hinge 4H No Charge5" hinges (up to 7' 6") 5 15.005" hinges (over 7' 6") 5 20.005" Heavy weight hinges (up to 7' 6") 5H 15.005" Heavy weight hinges (over 7' 6") 5H 20.00

CASED OPEN (see cased open sick for pricing) CO No ChargeSPECIAL CONSTRUCTION ADDERS

Drywall returns1' DW 4.00

10' 7" DW 40.00SPECIAL HARDWARE LOCATIONS

DEFAULT - Mesker locations No ChargeCustom lock height No Add for SDI member locations SLL 30.00Custom hinge locations No Add for SDI member locations SHL 30.00

HOSPITAL STOPS4" & 45 Degree (per jamb) 75.006" & 45 Degree (per jamb) 75.008" & 45 Degree (per jamb) 75.004" & 90 Degree (per jamb) 75.006" & 90 Degree (per jamb) 75.008" & 90 Degree (per jamb) 75.00

TAGGINGTag - opening number is listed on component label (per component) No Charge


M SERIES - MULLION

STANDARD DEPTHS CUSTOM DEPTHS

Mullions: L: 4-3/4 & 5-3/4 6-3/4 7-3/4, 8-1/4

& 8-3/44-1/2 & 4-5/8

4-7/8 & 6-5/8

6-7/8 & 8-5/8

8-7/8 to 12-3/4

12-7/8 to 14-3/4

BLANK MULL1' 26 27 29 44 48 51 56 65

10' 7" 260 270 290 440 480 510 560 650

HINGE 68,70,721' Per foot = (desired length in BLANK MULL) + (qty of hinges x hinge charge)

10' 7" 350 360 380 530 570 600 650 740

HINGE 76 & UP1' Per foot = (desired length in BLANK MULL) + (qty of hinges x hinge charge)

10' 7" 380 390 410 560 600 630 680 770

STRIKE1' Per foot = (desired length in BLANK MULL) + (qty of hinges x hinge charge)

10' 7" 290 300 320 470 510 540 590 680

DBL HINGE 68,70,721' Per foot = (desired length in BLANK MULL) + (qty of hinges x hinge charge)

10' 7" 440 450 470 620 660 690 740 830

DBL HINGE 76 & UP1' Per foot = (desired length in BLANK MULL) + (qty of hinges x hinge charge)

10' 7" 470 480 500 650 690 720 770 860

DBL STRIKE1' Per foot = (desired length in BLANK MULL) + (qty of hinges x hinge charge)

10' 7" 320 330 350 500 540 570 620 710

HINGE & STRIKE 68,70,721' Per foot = (desired length in BLANK MULL) + (qty of hinges x hinge charge)

10' 7" 380 390 410 560 600 630 680 770

HINGE & STRIKE 76 & UP1' Per foot = (desired length in BLANK MULL) + (qty of hinges x hinge charge)

10' 7" 410 420 440 590 630 660 710 800

BLANK HDW SECTION1' – – – – – – – –

10' 7" 90 90 90 – – – – –

HINGE HDW SECTION (<75)1' – – – – – – – –

10' 7" 180 180 180 – – – – –

STRIKE HDW SECTION1' – – – – – – – –

10' 7" 120 120 120 – – – – –

STOP SECTION1' – – – – – – – –

10' 7" 170 180 200 – – – – –

CORNER POST1' 59 63 66 – 63 66 71 80

10' 7" 600 630 660 – 680 690 720 800

Equal Rabbet Mullion1' 48 49 51 66 70 73 78 87

10' 7" 480 490 510 660 700 730 780 870

Single Rabbet Mullion1' 42 44 49 47 47 58 68 –

10' 7" 415 441 493 468 474 580 678 –

Cased Open Mullion1' 41 42 48 46 48 53 – –

10' 7" 430 457 515 482 518 601 – –

Used: Profiles under 4-3/4" Profiles over 8-3/4" Faces other than 2"

Standard

Custom Profile


M SERIES - OPTIONS


FRAME SERIESMullion M No Charge

COMPONENT TERMINOLOGYBlank mullion BM No ChargeHinge mullion HM No ChargeStrike mullion SM No ChargeDouble hinge mullion DHM No ChargeDouble strike mullion DSM No ChargeHinge & strike mullion HSM No ChargeBlank hardware section MHSB -Hinge hardware section MHSH No ChargeHinge hardware section - hinge both sides MHSDH No ChargeStrike hardware section MHSS No ChargeStrike hardware section - strike both sides MHSDS No ChargeHinge & strike section MHSHS No ChargeStop section MSS No ChargeCorner post No Charge

DOOR POCKET1 3/4" Door pocket 4 No ChargeNo door pocket (cased open or blank) 0 No ChargeKERF 1 3/4" (per component) (max 90min fire) (cost includes weatherstrip) 4-KERF 153.00

SPECIAL FACESSpecial profiles from 4-3/4" - 8-3/4" No Charge

Special depth, (add to next larger size)1' 1.00

10' 7" 50.00Special profiles larger than 8 3/4":Use custom profile pricing

SPECIAL FACES (only available for Range Profile)2" Face No Charge

1 1/8"-4" Face (add to 2" face mullion)1' W#F 7.00

10' 7" W#F 70.00

6" Face (add to 2" face mullion)1' W6F 15.00

10' 7" W6F 150.00

8" Face (add to 2" face mullion)1' W8F 23.00

10' 7" W8F 230.00

10" Face (add to 2" face mullion)W10F 31.00W10F 310.00

12" Face (add to 2" face mullionW12F 39.00W12F 390.00

GAUGEDEFAULT = 16 Gauge 16 No Charge

14 Gauge (add to 2 piece mullions1' 14 7.00

10' 7" 14 70.00

14 Gauge (add to hardware sections)1' 14 7.00

10' 7" 14 70.00

14 Gauge (add to stop sections)1' 14 7.00

10' 7" 14 70.00STEEL TYPES

Galvannealed - A40 - (per component)1' Z No Charge

10' 7" Z No Charge

Galvannealed - A60 - (per component)1' Z 1.00

10' 7" Z 10.00

Galvanized - G90 (per component)1' G90 36.00

10' 7" G90 360.00


M SERIES - OPTIONS


LOCKS / LATCHESDEFAULT = PREP: ASA strike, 4 7/8" on Strike Mullions – No ChargePREP: additional ASA strike US 30.00PREP: T strike, 2 3/4" C 30.00

INTERCONNECTED LOCKSPREP: interconnected strike (4" ctc) HS 100.00

DEADLOCKSPREP: deadlock strike (default height = 48" ctr to floor) DBS 30.00

ROLLER LATCHPREP: roller latch strike at lock height - (use ASA or T strike pricing) on strike stick - or C No ChargePREP: roller latch strike in header (each) ASA or T strike RL 30.00




ELECTRIFIED HARDWAREPREP: electric strike prep junction box not included add pe below if required ES 60.00PREP: electric hinge prep junction box not included add pe below if required EH 22.00PREP: electric power transfer (EPT) junction box not included add per below if required EPT 67.00PREP: door position switch (DPS) (hole only) junction box not included add pe below if required DPS1 21.00

PREP: door position switch (DPS) (with tabs) junction box not included add pe below if required DPS2 43.00

REINFORCEMENT: junction box JBOX 30.00INACTIVE LEAF PREPS

Standard flush bolt strike prep FB 51.00LABELED FRAMES (UL-Canada now available by request

Mylar - single frame 25.00Metal - single frame 30.00

HINGE REINFORCEMENTS (add to cost of Hinge Stick)4 1/2" X 4 1/2" STD or HW weight hinge up to 7'6" 4 No Charge4 1/2" X 4 1/2" STD or HW weight hinge over 7'6" 4H No Charge5" hinges (up to 7' 6") 5 15.005" hinges (over 7' 6") 5 20.005" Heavy weight hinges (up to 7' 6") 5H 15.005" Heavy weight hinges (over 7' 6") 5H 20.00

SPECIAL HARDWARE LOCATIONSDEFAULT - Mesker locations No ChargeCustom lock height No Add for SDI member locations SLL 30.00Custom hinge locations No Add for SDI member locations SHL 30.00

HOSPITAL STOPS4" & 45 Degree (per jamb) 75.006" & 45 Degree (per jamb) 75.008" & 45 Degree (per jamb) 75.004" & 90 Degree (per jamb) 75.006" & 90 Degree (per jamb) 75.008" & 90 Degree (per jamb) 75.00

REMOVABLE MULLIONRemovable Mullon prep (add this to cost of mullion) (anchors included)*Cost of hardware preps are additional 300.00

TAGGINGTag - opening number is listed on component label (per component) No Charge


CUT & NOTCH

Description Image List

MITERED CORNER - STICK

45 Degree cut, no tabs, price per end 15.00

NOTCH - STICK

Square, cut & notch, price per end 20.00

NOTCH - MULLION

NOTCH - MULLION 40.00

PARTIAL SIDELITE MULLION NOTCH

Back notch 178.00

INSTALLED HATS

Square, cut, tack welded 224.00

GLAZING BEAD

5/8" x 5/8" x 10'. FHD SCREW #10 X 1 1/4 32.00

DRYWALL COMPRESSION ANCHOR

Install compression anchor (each) 25.00

WELDED + GLAZING BEAD

Description Image List

CORNER JOINT

Face weld, primed, included both sides / priced per joint 22.00

MULLION T JOINT


CENTER JOINT


HINGE PREP

4.5" x 4.5" Standard weight 30.00

STRIKE PREP

4 7/8" ASA strike 30.00

PARTIAL SIDELITE MULLION NOTCH

Back notch 178.00

INSTALLED HATS

Square, cut, tack welded 224.00

GLAZING BEAD + CUT TO SIZE

5/8" x 5/8" x 1' 4.00

FIELD SPLICE

for oversized frame - priced per slice 200.00

METAL PANEL18 GA per square foot A40 (3/4" Sandwhich Panel) 55.0016 GA per square foot A40 (3/4" Sandwhich Panel 55.0014 GA per square foot A40 (3/4" Sandwhich Panel 75.00For fire rated panel, build ST Series door without preps Per Price Book Page 16Install panel 275.00


PARTS - DOORS


HINGE PARTS - DOORDF door hinge filler plate PD401 14.00Template hinge shim 4 1/2" PD42S 2.00Short door hinge (HR450) PDNHR450 7.00Short door hinge 5" (HR500) PDNHR500 14.00Long door hinge (LHR450) PDNLHR450 8.00Hinge filler (handing plate) 4 1/2" (HFDP450) PDHF4 2.00Hinge filler (handing plate) 4 1/2" (heavy weight) PDHF4H 3.00Hinge Filler (handing plate) 5" (HFP500) PDHF5 5.00Hinge Filler (handing plate) 5" (heavy weight) PDHF5H 5.00

INTERCONNECTED LOCKSStrike adapter PD86SA 23.00Cylindrical lock box (C4) PDCLB 7.00Strike tab reinforcement 8-32 (RCS001) PDCR 5.00Strike tab reinforcement 12-24 (RMS401) PDMR 5.00Cylindrical lock edge filler (CLE161) PDLEC 4.00Cylindrical lock face filler (CLF161) PDLFC 21.00Mortise lock filler (MLE086) PDLEM 11.00Filler change MB to C4 edge PDLMC 23.00Flush bolts reinforcment tab (MBR001) PDFBA 6.00Flush bolt guide (MBR401) PDFBG 13.00

ASTRAGALSFlat astragal (68) PDFA (68) 50.00Flat astragal (70) PDFA (70) 50.00Flat astragal (72) PDFA (72) 50.00Flat astragal (80) PDFA (80) 60.00Flat astragal (100) PDFA (100) 60.00Z astragal blank 6'8" PDZAB68 105.00Z astragal blank 7' PDZAB70 105.00Z astragal blank 8' PDZAB 105.00Z astragal blank 10' PDZABT 125.00Z astragal + U strike 6'8" NONHANDED PDZAU68 105.00Z astragal + U strike 7' RH PDZAU70R 105.00Z astragal + U strike 7' LH PDZAU70L 105.00Z astragal + U strike 8' RH PDZAU80R 105.00Z astragal + U strike 8' LH PDZAU80L 105.00Z astragal + U strike 10' PDZAUT 125.00Z astragal + U strike 6'8" RH + FB Prep PDZAU68RFB 128.00Z astragal + U strike 6'8" LH + FB Prep PDZAU68LFB 128.00Z astragal + U strike 7' RH + FB Prep PDZAU70RFB 128.00Z astragal + U strike 7' LH + FB Prep PDZAU70LFB 128.00Z astragal + U strike 8' RH + FB Prep PDZAU80RFB 128.00Z astragal + U strike 8' LH + FB Prep PDZAU80LFB 128.00Flat Astragal cut to size price next largest size 165.00“Z” Astragal w/ ASA & F.B. cut to size (handing required) PDMAC 162.00“Z” Astragal w/ F.B. cut to size (handing required) PDMACF 142.00Astragal screw #6 x 1/2 (qty 5) PFASCREW 1.00

DOOR ASSEMBLY PARTSTop & bottom channel 3' (TC-430) PDTC3 21.00Top & bottom channel 4' (TC-440) PDTC4 25.00Top channel 10' (TC4100) PDC10 73.006' Channel reinforcement for cutouts PDCOC 51.00Door conversion style (DCS) (used to change door width in shop) PDDCS 47.00Door caps 30 (metal snap in) PDSICAP30 30.00Door caps 40 (metal snap in) PDSICAP40 30.00Door caps 30 w/ holes (metal snap in) PDSICAP30WH 41.00Door caps 40 w/ holes (metal snap in) PDSICAP40WH 41.00FCS cap to flush door top (30) PDCAP30 21.008" Dutch shelf (30) DS0830 425.00


PARTS - FRAMES


ANCHORSWire (case = 500) PFMWA 2.00T 4 3/4 PFMT4 4.00T 5 3/4 PFMT5 4.00T 6 3/4 PFMT6 4.00T 7 3/4 PFMT7 4.00T 8 3/4 PFMT8 4.00T 5 3/4 - Double egress PFDE684 7.00Multi-Purpose egress anchor-5 PFDE680 7.00Universal 4 3/4 PFUA4 3.00Universal 5 3/4 (case = 350) PFUA5 3.00Universal 6 3/4 PFUA6 3.00Universal 7 1/4 PFUA725 3.00Universal 7 3/4 PFUA7 3.00Universal 8 1/4 PFUA825 3.00Universal 8 3/4 PFUA8 3.00Adjustable anchor (110) 4 3/4 to 6 3/4 PFA110 7.00Adjustable anchor (380) 5 3/4 to 8 3/4 PFA380 7.00Adjustable anchor (380A) 8 3/4 to 12 3/4 PF380A 8.00Wood stud strap anchor ea. PFWSSA 1.00Steel stud anchor 5 3/4 PFSSA5 3.00ZEE anchor (specify size) - 3.00

Flat head SLEEVE anchor - 3/8" x 5" PFSA3/8X5 8.00Flat head SLEEVE anchor - 3/8" x 6" PFSA3/8X6 8.00

Flat head WOOD screw - 3/8" x 5" PFLB3/8X5 6.00Flat head WOOD screw - 3/8" x 6" PFLB3/8X6 6.00Tube PFMTA 5.00

Sill anchor 4 3/4 PFSA4 3.00Sill anchor 5 3/4 PFSA5 3.00Sill anchor 6 3/4 PFSA6 3.00Sill anchor 7 3/4 PFSA7 3.00Sill anchor 8 3/4 PFSA8 3.00Adjustable floor anchor (4 3/4 thru 8 3/4) PFAAF 5.00Drywall snap in anchor (2 needed per jamb) PFDSNA 1.00Drywall compression anchor PFDCA 8.00

Mullion anchor 4 3/4 PFMUA4 9.00Mullion anchor 5 3/4 PFMUA5 9.00Mullion anchor 6 3/4 PFMUA6 9.00Mullion anchor 7 3/4 PFMUA7 9.00Mullion anchor 8 3/4 PFMUA8 9.00

CLOSER REINFORCEMENTS - FRAMESCloser reinforcement frame face (CRF) PFFCR 5.00Closer reinforcement 4-1/2 frame (CRB) PFSOR45 5.00Closer sleeve (4 1/2) PFSCR45 24.00Closer sleeve (4 3/4) PFSCR47 24.00Closer sleeve (5 5/8) PFSCR56 24.00Closer sleeve (5 3/4) PFSCR57 24.00Closer sleeve (5 7/8) PFSCR58 24.00Closer sleeve (6 1/4) PFSCR62 24.00Closer sleeve (6 3/4) PFSCR67 24.00Closer sleeve (7 1/8) PFSCR712 24.00Closer sleeve (7 3/4) PFSCR77 24.00Closer sleeve (8 1/4) PFSCR82 24.00Closer sleeve (8 3/4) PFSCR87 24.00Closer sleeve (specify profile) PFSCRXX 24.00Steel glazing bead 5/8" x 5/8" x 10' PFSGB 32.00


PARTS - FRAMES


HINGE PARTS -FRAMESFrame hinge filler plate PF402 5.003-1/2" Hinge reinforcement PF3HR 4.004-1/2" Hinge reinforcement PF4HR 4.005" Hinge reinforcement PF5HR 9.004-1/2" Hinge reinforcement HVY. WT. PF4HHR 6.005" Hinge reinforcement HVY. WT. PF5HHR 9.003-1/2 Hinge plaster guard PF3PG 2.004-1/2 Hinge plaster guard PF4PG 2.00

STRIKE PARTS - FRAMESReversible flush bolt strike & reinf. PFFBREV 18.00Strike filler 2-3/4 PFFCS 5.00Strike filler 4-7/8 PFFUS 5.00ASA Strike reinforcement 4-7/8 PFSRU 3.002-3/4 Strike reinforcement cyl. "T" STRIKE PFSRC 3.00

MISCELLANEOUS FRAME PARTSSpreader bar 3' PFSB3 5.00Spreader bar 6' PFSB6 10.00Spreader bar 8' PFSB8 13.00Plastic plug for UNA 5-3/4 PFPP 1.00Mutes - push through (qty 5) PFPTM 1.00Mutes - stick on (qty 2) PFSOM 1.00Mullion clips PFMC 1.00Frame corner tabs PFTAB 1.00#8 x 1/2 phillips flat screw (qty 2) PFASCREW 1.00Glazing bead screws #10 x 1-1/4 (qty 2) PFGSCREW 1.00

PAINTQty: 4 - 1 gallon cans of primer direct shipped from manufacturer – 560.00

Providing total openings solutions, BASED ON INNOVATION AND TRADITION COMBINED.

meskerdoor.com 256-851-66703440 Stanwood Blvd NE, Huntsville, AL 35811

KA

A14

58 0

6-21

R2

Tradition, quality, and expertise.

Documents

Transcript of Tradition, quality, and expertise.