7/28/2019 TQ 503 Module 1 Solution

1/3

B. Tech.

Industrial Engg. & Mgmt.

(Spl. in TQM)

Name: .. SID No: .. Date: 10/07/11

Duration: 6 min Max. Marks: 3 Marks obtained:

Tick ( ) most appropriate choice.1. Cost of correcting errors at process planning stage are approximately ___ more than cost

of correcting errors at product design stage.

a) Ten times b) Hundred times

c) One thousand times d) Ten thousand times

2. When management prevents or corrects unwanted bad change, this process is knownas_____.

a) Control b) breakthroughc) Strategic planning d) Quality planning

3. Breakthrough is a deliberate change, a dynamic, decisive movement to unprecedentedhigher levels of organizational performance.

a) True b) False

4. During prototype design ______ is used as a form of early warning of new producttrouble.

a) Concept review b) PFMEA

c) Prototype test d) DFMEA

5. Understanding gap is lack of understanding of what the ________

a) customer really needs b) designer should do

c) supplier should do d) None of the above

6. The following vehicle was developed using Jurans quality roadmap.

a) Tata 407 b) Mahindra Scorpio

c) Both a and b d) Neither a nor b

7. The basic model of Tata Nano will be fitted with ______

a) Air conditioner b) Power steering

c) Both a and b d) None of the above

8. Before beginning regular operations, the process must be capable of meeting ____ goals.

a) design b) customer

c) Quality d) trial

9. Tata Nano is 8% shorter than Maruti 800, but ______ roomier inside.

a) 30% b) 21%

c) 11% d) 3%

10. Control is an essential part of quality planning but not necessary for breakthroughimprovement.

a) True b) False

11. Critical factors are those aspects which present serious danger to _____

a) human life b) health

c) environment d) All of the above

12. Product features answer the question, What characteristics of the product do we need tomeet _____ needs?

a) human b) customer

TQ 503 Mod 1 Quiz A

7/28/2019 TQ 503 Module 1 Solution

2/3

B. Tech.

Industrial Engg. & Mgmt.

(Spl. in TQM)

c) environment d) design

7/28/2019 TQ 503 Module 1 Solution

3/3

B. Tech.

Industrial Engg. & Mgmt.

(Spl. in TQM)

Name: .. SID No: .. Date: 10/07/11

Duration: 6 min Max. Marks: 3 Marks obtained:

Tick ( ) most appropriate choice.1. Cost of correcting errors at prototype testing stage are approximately ___ more than cost

of correcting errors at product design stage.

a) Ten thousand times b) Hundred times

c) Ten times d) One thousand times

2. Breakthrough is an accidental change to unprecedented higher levels of organizationalperformance than is currently in the plan and maintained by current controls.

a) True b) False

3. During process design ______ is used as a form of early warning of potential processfailure.

a) QFD b) In-house testing

c) DFMEA d) PFMEA

4. Control is an integral part of quality planning as well as for breakthrough improvement.

a) True b) False

5. During prototype construction, ______ is used as a form of early warning of new producttrouble.

a) Concept review b) In-house testing

c) Prototype test d) FMEA

6. Quality planning is the activity of establishing quality goals and developing the productsand processes required to meet those goals.

a) True b) False

7. Product development translates customer expectations for functional requirements intospecific _________.

a) features and processes b) process and design needs

c) engineering and quality characteristics d) design requirements

8. Process gap is concerned with inability of designed process to consistently produce______

a) designed product b) good products

c) quality products d) None of the above

9. The following vehicle was developed using Jurans quality roadmap.

a) Tata Nano b) Mahindra Scorpio

c) Both a and b d) Neither a nor b

10. Before beginning regular operations, the process must be capable of meeting ____ goals.

a) trial b) Quality

c) process design d) product design

11. Critical factors are those aspects which present serious danger to _____

a) human life b) health

c) environment d) All of the above

12. Tata Nano is fitted with a _____ body

a) Fibre glass b) Sheet metal

c) Plastic d) Aluminium

TQ 503 Mod 1 Quiz B