892019 TPE 575 CHIMEI

httpslidepdfcomreaderfulltpe-575-chimei 15

Trang 1

TPE PB-575SẢN PHẨM CỦA CHI MEI

TPE PB-575SẢN PHẨM CỦA CHI MEI

SPECIFICITY

- General purpose grade

- Oil Extended thermal plastic elastomer

-

High flow and has widest applications which may be used with large quantity of additives used in sole

and machinery products

CHARACTERISTIC

Typical Properties Test Method Units PB-575

Butadiene-Styrene ratio ASTM D-1416 Wt 6040

Volatile ASTM D-1416 Wt ＜06

Oil Content ASTM D-1416 phr 50

Melt Flow Index ASTM D-1238 200degC 5 g

g10min

60

Hardness ASTM D-2240 Shore A 63

PROCESSING GUIDE

The injection temperature is between 130degC~190degC

APPLICATION

- TPE PB-575 can be mixed with GPPS to manufacture shoe sole industrial accessory

- Asphaltbitumen modifier for roads and roofing

- Adhesives Shoe soles Instrument handles Toys

REMARKS

TPE PB-575 meets the requirements of Japan High Polymer Center

Tại Việt Nam sản phẩm TPE PB-575 trecircn được tiếp thị tư vấn sử dụng phacircn phối bởi

Cocircng Ty TNHH RICH DEM ANDER (VN)

Địa chỉ Locirc 01 Tacircn Thuận KCX Tacircn Thuận P Tacircn Thuận Đocircng Quận 7 TPHCM

Tel (08) 37700899 EXT 313- Fax (08) 37700897 Email haihuynh1510yahoocom

Website http wwwchimeicorpcom

Vui lograveng liecirc n hệ chuacuteng tocirci khi quiacute vị cần thecircm thocircng tin sản phẩm

892019 TPE 575 CHIMEI

httpslidepdfcomreaderfulltpe-575-chimei 25

59-1 SAN CHIA JEN TE TAINAN COUNTY TAIWANTEL 886-6-266-5000 FAX 886-6-266-5555~7

TPE KIBITON

reg

PB-575 February 1 2012 V1W

Typical Characteristic

Properties Test Method Test Condition Unit PB-575

BDSM Ratio ASTM D1416 - 5842

Volatile matter ASTM D1416 - wt 06

Ash Content ASTM D1416 - wt 03

Oil Content ASTM D1416 - phr 50

Melt Flow Index ASTM D1238 200983084983093983115983143 g10min 70

Melt Flow Index ASTM D1238 190983084983093983115983143 g10min 45

Hardness ASTM D2240 - Shore A 65

Specific Gravity ASTM D792 23 - 094

Appearance - - 983085 Foam Pellet

Bale Weight - - 983115983143 20

The data are intended as a general guide only and do not necessarily represent results that may

be obtained elsewhere

For further information please contact your local agent or fax to Chi Mei Technical Services Dept at

886-6-2665555

892019 TPE 575 CHIMEI

httpslidepdfcomreaderfulltpe-575-chimei 35

CH I M EI CORPORAT I ON

59-1 SAN CHI A JEN TE TAINAN COUNTY TAIWAN ROC TEL 886-6-266-5000 FAX 886-6-266-5555~7

KIBITON reg PB-575

Recommended Processing Condition

A Predrying 60~70degC 1~2 hr

depending on a) Humidity b) Ratio of Regrind c) Storage conditions

B Barrel Setting Profile

Metering Zone Compression Zone Feeding Zone

Max(degC) 190 190 150

Min(degC) 150 150 130

The suggested processing temperature is 160~170degC

C Mold Temperature30~70degC

depending on a) Thickness b) Dimension c) Gate and runner system

D Injection Pressure 20~80 kgcm2

Holding Pressure 20~40 kgcm2

Back Pressure 5~10 kgcm2

E Purging

Purging for shutdown should include complete removal of PB-575 with either PE or

GPPS(PG-33)

NOTE 1 Keep the resin from dust and contamination during handling and production

2 Do not retain the hot melt at the barrel for a long time between injection cycles

892019 TPE 575 CHIMEI

httpslidepdfcomreaderfulltpe-575-chimei 45

59-1 SAN CH IA JEN TE TAINAN CITY TAIWAN

TEL 886-6-266-5000 FAX 886-6-266-5555~7

Mater ial Safety Data Sheet Apr i l 01 2014 V1W

Product Name KIBITONreg

PB-511 PB-575 PB-5301 PB-5302 PB-5502

KIBIPOLreg

PR-1205

1 COMPANY IDENTIFICATION

Company Chi Mei CorporationAddress 59-1 San Chia Jen Te Tainan City Taiwan ROCInformation Phone No 886-6-2663000Emergency Phone No 886-6-2663000Fax No 886-6-2667981

2 COMPOSITION INFORMATION ON INGREDIENTS

Substance or Preparation SubstanceChemical Name Styrene-Butadiene CopolymerFormula (C8H8C4H6)x

CAS No 9003-55-8Impurities Contributing to Hazard None

3 HAZARD IDENTIFICATION

Most Important Hazards NoneAdverse Human Health Effects NoneEnvironmental Effects NonePhysical and Chemical Hazards None

4 FIRST AID MEASURES

Inhalation In case of gases evolving from melted resin move subject to fresh air Treat

symptomaticallySkin Contact In case of pellets or powder wash with water

In case of melt wash affected skin area and clothing with plenty of (soap and) water seekmedical advice

Eye Contact In case of pellets or powder flush with plenty of water for at least 15 minutes Seek medicaladvice if any dust particles still remain

In case of gases evolving from melted resin of high temperature flush with plenty of waterfor at least 15 minutes Seek medical advice if necessary

Ingestion Induce vomiting Rinse mouth with water Seek medical advice if necessary

5 FIRE-FIGHTING MEASURES

Extinguishing Media Water Foam Dry chemical powder

Special Fire-Fighting Procedure Self contained breathing apparatusFire and Explosion Hazards None

6 ACCIDENTAL RELEASE MEASURES

Methods for Cleaning up Recovery if not contaminated or DisposalPersonal Precautions Pellets or powder remained on ground may cause slippingEnvironmental Precautions Gather pellets and powder thoroughly to avoid birds or fishes taking from

draining water

7 HANDLING AND STORAGE

Handling Prevent from fire around handling area Maintain good housekeeping standards to preventaccumulation of dust To avoid dust explosion resulting from the existence of powder

electrostatics eliminators and grounding should be fixed to such equipment as air transferring pipes bag filters and hoppers Use electrically conductive filters for bag filters

Storage Keep the materials at a cool dry place Protect from direct sunlight rain and violent temperaturefluctuation Fire is inhibited around storage area

892019 TPE 575 CHIMEI

httpslidepdfcomreaderfulltpe-575-chimei 55

59-1 SAN CH IA JEN TE TAINAN CITY TAIWAN

TEL 886-6-266-5000 FAX 886-6-266-5555~7

8 EXPOSURE CONTROLS PERSONAL PROTECTION

Threshold Limit Value Not determined

Ventilation Necessary to exclude dust fumes and gases

Personal Protection Eye Wear safety glasses for general purpose Wear chemical goggles for

cleaning molding machinesRespiratory Wear masks for cleaning molding machines

Gloves Necessary for handling melted resin

9 PHYSICAL AND CHEMICAL PROPERTIES

Appearance Off white pellets

Melting Temperature Start Softening above 70

degC

Solubility Insoluble in water

Specific Gravity 092 ~ 095

10 STABILITY AND REACTIVITY

Flammability Yes

Flash Point Not Applicable

Autoignition Temperature Not Applicable

Reactivity with Water No

Stability Stable and non-reactive under normal handling and storage condition

Thermal Decomposition Gases CO SM and NO

Combustion Energy 353 x 107 Jkg (8424 Kcalkg)

11 HEALTH HAZARD DATA

Irritation Fumes or vapors generated from decomposing resin may be irritant to eyes

Acute oral toxicity (LD50) Not determined

Mutagenicity Not determined

12 ECOLOGICAL INFORMATION

Put into containers for reclaiming or disposal

13 DISPOSAL CONSIDERATIONS

Controlled incineration or landfill according to local state or national laws and regulations concerning health

and pollution

Inadequate incineration may generate toxic gases such as CO and SM

14 TRANSPORT INFORMATION

Not classified

15 REGULATORY INFORMATION

Not available

16 OTHER INFORMATION

None

892019 TPE 575 CHIMEI

httpslidepdfcomreaderfulltpe-575-chimei 35

CH I M EI CORPORAT I ON

59-1 SAN CHI A JEN TE TAINAN COUNTY TAIWAN ROC TEL 886-6-266-5000 FAX 886-6-266-5555~7

KIBITON reg PB-575

Recommended Processing Condition

A Predrying 60~70degC 1~2 hr

depending on a) Humidity b) Ratio of Regrind c) Storage conditions

B Barrel Setting Profile

Metering Zone Compression Zone Feeding Zone

Max(degC) 190 190 150

Min(degC) 150 150 130

The suggested processing temperature is 160~170degC

C Mold Temperature30~70degC

depending on a) Thickness b) Dimension c) Gate and runner system

D Injection Pressure 20~80 kgcm2

Holding Pressure 20~40 kgcm2

Back Pressure 5~10 kgcm2

E Purging

Purging for shutdown should include complete removal of PB-575 with either PE or

GPPS(PG-33)

NOTE 1 Keep the resin from dust and contamination during handling and production

2 Do not retain the hot melt at the barrel for a long time between injection cycles

892019 TPE 575 CHIMEI

httpslidepdfcomreaderfulltpe-575-chimei 45

59-1 SAN CH IA JEN TE TAINAN CITY TAIWAN

TEL 886-6-266-5000 FAX 886-6-266-5555~7

Mater ial Safety Data Sheet Apr i l 01 2014 V1W

Product Name KIBITONreg

PB-511 PB-575 PB-5301 PB-5302 PB-5502

KIBIPOLreg

PR-1205

1 COMPANY IDENTIFICATION

Company Chi Mei CorporationAddress 59-1 San Chia Jen Te Tainan City Taiwan ROCInformation Phone No 886-6-2663000Emergency Phone No 886-6-2663000Fax No 886-6-2667981

2 COMPOSITION INFORMATION ON INGREDIENTS

Substance or Preparation SubstanceChemical Name Styrene-Butadiene CopolymerFormula (C8H8C4H6)x

CAS No 9003-55-8Impurities Contributing to Hazard None

3 HAZARD IDENTIFICATION

Most Important Hazards NoneAdverse Human Health Effects NoneEnvironmental Effects NonePhysical and Chemical Hazards None

4 FIRST AID MEASURES

Inhalation In case of gases evolving from melted resin move subject to fresh air Treat

symptomaticallySkin Contact In case of pellets or powder wash with water

In case of melt wash affected skin area and clothing with plenty of (soap and) water seekmedical advice

Eye Contact In case of pellets or powder flush with plenty of water for at least 15 minutes Seek medicaladvice if any dust particles still remain

In case of gases evolving from melted resin of high temperature flush with plenty of waterfor at least 15 minutes Seek medical advice if necessary

Ingestion Induce vomiting Rinse mouth with water Seek medical advice if necessary

5 FIRE-FIGHTING MEASURES

Extinguishing Media Water Foam Dry chemical powder

Special Fire-Fighting Procedure Self contained breathing apparatusFire and Explosion Hazards None

6 ACCIDENTAL RELEASE MEASURES

Methods for Cleaning up Recovery if not contaminated or DisposalPersonal Precautions Pellets or powder remained on ground may cause slippingEnvironmental Precautions Gather pellets and powder thoroughly to avoid birds or fishes taking from

draining water

7 HANDLING AND STORAGE

Handling Prevent from fire around handling area Maintain good housekeeping standards to preventaccumulation of dust To avoid dust explosion resulting from the existence of powder

electrostatics eliminators and grounding should be fixed to such equipment as air transferring pipes bag filters and hoppers Use electrically conductive filters for bag filters

Storage Keep the materials at a cool dry place Protect from direct sunlight rain and violent temperaturefluctuation Fire is inhibited around storage area

892019 TPE 575 CHIMEI

httpslidepdfcomreaderfulltpe-575-chimei 55

59-1 SAN CH IA JEN TE TAINAN CITY TAIWAN

TEL 886-6-266-5000 FAX 886-6-266-5555~7

8 EXPOSURE CONTROLS PERSONAL PROTECTION

Threshold Limit Value Not determined

Ventilation Necessary to exclude dust fumes and gases

Personal Protection Eye Wear safety glasses for general purpose Wear chemical goggles for

cleaning molding machinesRespiratory Wear masks for cleaning molding machines

Gloves Necessary for handling melted resin

9 PHYSICAL AND CHEMICAL PROPERTIES

Appearance Off white pellets

Melting Temperature Start Softening above 70

degC

Solubility Insoluble in water

Specific Gravity 092 ~ 095

10 STABILITY AND REACTIVITY

Flammability Yes

Flash Point Not Applicable

Autoignition Temperature Not Applicable

Reactivity with Water No

Stability Stable and non-reactive under normal handling and storage condition

Thermal Decomposition Gases CO SM and NO

Combustion Energy 353 x 107 Jkg (8424 Kcalkg)

11 HEALTH HAZARD DATA

Irritation Fumes or vapors generated from decomposing resin may be irritant to eyes

Acute oral toxicity (LD50) Not determined

Mutagenicity Not determined

12 ECOLOGICAL INFORMATION

Put into containers for reclaiming or disposal

13 DISPOSAL CONSIDERATIONS

Controlled incineration or landfill according to local state or national laws and regulations concerning health

and pollution

Inadequate incineration may generate toxic gases such as CO and SM

14 TRANSPORT INFORMATION

Not classified

15 REGULATORY INFORMATION

Not available

16 OTHER INFORMATION

None

892019 TPE 575 CHIMEI

httpslidepdfcomreaderfulltpe-575-chimei 45

59-1 SAN CH IA JEN TE TAINAN CITY TAIWAN

TEL 886-6-266-5000 FAX 886-6-266-5555~7

Mater ial Safety Data Sheet Apr i l 01 2014 V1W

Product Name KIBITONreg

PB-511 PB-575 PB-5301 PB-5302 PB-5502

KIBIPOLreg

PR-1205

1 COMPANY IDENTIFICATION

Company Chi Mei CorporationAddress 59-1 San Chia Jen Te Tainan City Taiwan ROCInformation Phone No 886-6-2663000Emergency Phone No 886-6-2663000Fax No 886-6-2667981

2 COMPOSITION INFORMATION ON INGREDIENTS

Substance or Preparation SubstanceChemical Name Styrene-Butadiene CopolymerFormula (C8H8C4H6)x

CAS No 9003-55-8Impurities Contributing to Hazard None

3 HAZARD IDENTIFICATION

Most Important Hazards NoneAdverse Human Health Effects NoneEnvironmental Effects NonePhysical and Chemical Hazards None

4 FIRST AID MEASURES

Inhalation In case of gases evolving from melted resin move subject to fresh air Treat

symptomaticallySkin Contact In case of pellets or powder wash with water

In case of melt wash affected skin area and clothing with plenty of (soap and) water seekmedical advice

Eye Contact In case of pellets or powder flush with plenty of water for at least 15 minutes Seek medicaladvice if any dust particles still remain

In case of gases evolving from melted resin of high temperature flush with plenty of waterfor at least 15 minutes Seek medical advice if necessary

Ingestion Induce vomiting Rinse mouth with water Seek medical advice if necessary

5 FIRE-FIGHTING MEASURES

Extinguishing Media Water Foam Dry chemical powder

Special Fire-Fighting Procedure Self contained breathing apparatusFire and Explosion Hazards None

6 ACCIDENTAL RELEASE MEASURES

Methods for Cleaning up Recovery if not contaminated or DisposalPersonal Precautions Pellets or powder remained on ground may cause slippingEnvironmental Precautions Gather pellets and powder thoroughly to avoid birds or fishes taking from

draining water

7 HANDLING AND STORAGE

Handling Prevent from fire around handling area Maintain good housekeeping standards to preventaccumulation of dust To avoid dust explosion resulting from the existence of powder

electrostatics eliminators and grounding should be fixed to such equipment as air transferring pipes bag filters and hoppers Use electrically conductive filters for bag filters

Storage Keep the materials at a cool dry place Protect from direct sunlight rain and violent temperaturefluctuation Fire is inhibited around storage area

892019 TPE 575 CHIMEI

httpslidepdfcomreaderfulltpe-575-chimei 55

59-1 SAN CH IA JEN TE TAINAN CITY TAIWAN

TEL 886-6-266-5000 FAX 886-6-266-5555~7

8 EXPOSURE CONTROLS PERSONAL PROTECTION

Threshold Limit Value Not determined

Ventilation Necessary to exclude dust fumes and gases

Personal Protection Eye Wear safety glasses for general purpose Wear chemical goggles for

cleaning molding machinesRespiratory Wear masks for cleaning molding machines

Gloves Necessary for handling melted resin

9 PHYSICAL AND CHEMICAL PROPERTIES

Appearance Off white pellets

Melting Temperature Start Softening above 70

degC

Solubility Insoluble in water

Specific Gravity 092 ~ 095

10 STABILITY AND REACTIVITY

Flammability Yes

Flash Point Not Applicable

Autoignition Temperature Not Applicable

Reactivity with Water No

Stability Stable and non-reactive under normal handling and storage condition

Thermal Decomposition Gases CO SM and NO

Combustion Energy 353 x 107 Jkg (8424 Kcalkg)

11 HEALTH HAZARD DATA

Irritation Fumes or vapors generated from decomposing resin may be irritant to eyes

Acute oral toxicity (LD50) Not determined

Mutagenicity Not determined

12 ECOLOGICAL INFORMATION

Put into containers for reclaiming or disposal

13 DISPOSAL CONSIDERATIONS

Controlled incineration or landfill according to local state or national laws and regulations concerning health

and pollution

Inadequate incineration may generate toxic gases such as CO and SM

14 TRANSPORT INFORMATION

Not classified

15 REGULATORY INFORMATION

Not available

16 OTHER INFORMATION

None

892019 TPE 575 CHIMEI

httpslidepdfcomreaderfulltpe-575-chimei 55

59-1 SAN CH IA JEN TE TAINAN CITY TAIWAN

TEL 886-6-266-5000 FAX 886-6-266-5555~7

8 EXPOSURE CONTROLS PERSONAL PROTECTION

Threshold Limit Value Not determined

Ventilation Necessary to exclude dust fumes and gases

Personal Protection Eye Wear safety glasses for general purpose Wear chemical goggles for

cleaning molding machinesRespiratory Wear masks for cleaning molding machines

Gloves Necessary for handling melted resin

9 PHYSICAL AND CHEMICAL PROPERTIES

Appearance Off white pellets

Melting Temperature Start Softening above 70

degC

Solubility Insoluble in water

Specific Gravity 092 ~ 095

10 STABILITY AND REACTIVITY

Flammability Yes

Flash Point Not Applicable

Autoignition Temperature Not Applicable

Reactivity with Water No

Stability Stable and non-reactive under normal handling and storage condition

Thermal Decomposition Gases CO SM and NO

Combustion Energy 353 x 107 Jkg (8424 Kcalkg)

11 HEALTH HAZARD DATA

Irritation Fumes or vapors generated from decomposing resin may be irritant to eyes

Acute oral toxicity (LD50) Not determined

Mutagenicity Not determined

12 ECOLOGICAL INFORMATION

Put into containers for reclaiming or disposal

13 DISPOSAL CONSIDERATIONS

Controlled incineration or landfill according to local state or national laws and regulations concerning health

and pollution

Inadequate incineration may generate toxic gases such as CO and SM

14 TRANSPORT INFORMATION

Not classified

15 REGULATORY INFORMATION

Not available

16 OTHER INFORMATION

None