TOYOTA COROLLA 2009– TVIP V4 PREPARATION...

TOYOTA COROLLA 2009 TVIP V4PREPARATION REMOTE ENGINE STARTER (RES)

Page 1 of 40Issue: C 03/25/08

Part #: PT398-02080 NOTE: Part number of this accessory may not be the same as the part number shown.Conflicts: Do not install into Manual Transmission Vehicles or Vehicles without RKE systems.

RecommendedToolsPersonal&VehicleProtection Description

Safety Glasses

Safety Gloves (Optional

Vehicle Protection Blankets, Parts Boxes

SpecialToolsCable Wire Routing Tool

InstallationToolsScrewdriver #2 Phillips, Phillips Jewelers, Flat Blade Jewelers

Nylon Panel Removal Tool e.g. Panel Pry Tool #1 Toyota SST# 00002-06001-01

Side Cutters

Torque Wrench 36 inlbf (4.07 Nm); 66.4 inlbf (7.5 Nm); 70.8 inlbf (8.0 Nm)

Utility Knife

Tape Clear, Electrical

Socket 10mm, extension

Pliers Needle Nose, Pliers

SpecialChemicalsCleaner

Glass Cleaner

x1

x1

x2 x1

x1

x40

x2

x1

x1

x1

x1

x1

x1

x3

Spanish x2

Spanish x1

Spanish x2

Spanish x2

x1 English x2

English x1

English x2

English x2

KitContents

AdditionalItems(may be required)

Item# Description

RecommendedSequence ofApplicationItem# Description

1 TVIP V5 System

2 TVIP V4 System

RES ECU

RES Harness

Harness Clamp Hood Switch

RES ECU Bracket

Wire Tie

Hood Switch Screw

Remote Label

Window Label

Owners GuideGateway ECU

Hood switch Harness

Scotch Lock

Butyl Tape

Gateway ECU Bracket

Foam Tape

M6 Screw

Key Tag

Engine Room Label

TOYOTA COROLLA 2009 TVIP V4PREPARATION REMOTE ENGINE STARTER (RES)


TableofContentsPreparationI. ............................................................................................................................ 1 3

Table of Contents1. ................................................................................................................................................2Wire Routing Overview2. .................................................................................................................................. 34

ProcedureII. ............................................................................................................................5 3 7Disassembly (Engine Compartment)1. ..................................................................................................................5Hood Switch Installation2. ......................................................................................................................................5Disassembly (Passengers Area)3. .........................................................................................................................9V4 Wire Harness Installation (Drivers Side)4. .....................................................................................................14V4 Wire Harness Installation (IP Panel)5. ............................................................................................................18V4 Wire Harness Installation (Steering Column)6. ..............................................................................................19V4 Wire Harness Installation (Passengers Side)7. ..............................................................................................20Hood Switch Harness Routing (Continued)8. ......................................................................................................21RES ECU and Gateway ECU Preparation9. .......................................................................................................24V4 Harness Installation (Glovebox Area)10. ..........................................................................................................24Hood Switch Pin11. ................................................................................................................................................25V4 Harness Installation (Continued)12. .................................................................................................................27Registration Preparation13. ...................................................................................................................................30Registration14. .......................................................................................................................................................31Tags and Labels15. ................................................................................................................................................35Completing the Installation16. ................................................................................................................................36

ChecklistIII. ........................................................................................................................... 3 7 3 9Accessory Function Checks1. ..............................................................................................................................37Vehicle Function Checks2. ...................................................................................................................................38

Addendum IIV. ..............................................................................................................................4 0

LegendDo not proceed until process has been completed.

Follow steps carefully to avoid damaging the Vehicle or AccessoryUse caution to avoid injury.

Used in Figures to call attention to specific tools recommended for the process.

Highlights a change in installation with respect to previous issue.

AccessoryInstallationPractice(readbeforeinstallation)Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory should follow approved guidelines to ensure a quality installation.These guidelines can be found in the Accessory Installation Practices document.This document covers such items as:

Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.)Safety (eye protection, checking torque procedure, etc.) Vehicle Disassembly/Reassembly (panel removal, part storage, etc.) Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.)

Please see your Toyota dealer for a copy of this document.

TOY

OTA

C

OR

OL

LA

2009

TV

IP V4

PREPA

RATIO

N

R

EM

OT

E E

NG

INE

STAR

TE

R (R

ES)

Page 3 of 40Issue: C

03/25/08

TVIP Vehicle Description

A 2D 14P WHITE

B WIRE TERMINAL (Not Used)

C E46 WIRE TERMINAL (Red Wire)D WHITE TAPE E FUSEF RELAYG E4 8P WHITEH RES ECU

I 20P WHITE (for RES ECU)

J 8P WHITE (for RES ECU)

K WIRE TERMINAL (Green/Red Wire)

L WIRE TERMINAL (White/Black Wire)

M 2P WHITE (for Hood Switch)N Gateway ECU

O 5P WHITE (for Gateway ECU)

P E92 2P WHITE (Male)

Q 1P WHITE (for Registration)R EM3 13P WHITE

A

B

D

FE G

C

JI

P

NO

K

LM

Q

R

H

WireH

arnessOutline(PassengersC

ompartm

ent)

TOY

OTA

C

OR

OL

LA

2009

TV

IP V4

PREPA

RATIO

N

R

EM

OT

E E

NG

INE

STAR

TE

R (R

ES)

Page 4 of 40Issue: C

03/25/08

J WIRE TERMINAL (Green/Red Wire)

K WIRE TERMINAL (White/Black Wire)

S Hood Switch

T 2P BLACK

U 2P WHITE

T

K

S

L

TU

WireH

arnessOutline(EngineC

ompartm

ent)

TOYOTA COROLLA 2009 TVIP V4PROCEDURE REMOTE ENGINE STARTER (RES)


1) Disassembly. (EngineCompartment)

Place the Vehicle in Park with a) the Parking Brake set.Disconnected the Negative b) Battery Terminal.

Protect the Fender.

Note the Battery Cable Position as it will be re-installed in the same position.

CAUTION:Do not touch the Positive Terminal.

ForBoltonEngineCoversRemove the Engine Cover.c)

Remove 2 Nuts.

ForCliponEngineCoversRemove the Engine Cover.d)

Pull up on the Engine Cover eas- ing the Rubber Grommets off of the Metal Studs on the Engine.

Dislodge the Relay block.e) Press in on the clip and slide it off its Bracket.

10mm Socket Fig. 1-1





2) HoodSwitchInstallation.Dislodge the Hood Lock a) Assembly.

Remove 3 Bolts.

Remove the Hood Lock b) Cable from the Hood Lock.Release the Spring from the c) Hood Lock.

Cut the Harness Clamp from d) the Hood Switch Harness.

Make sure to hold the Hood Switch by the its sides. If the Hood Switch is broken RES will not function.

Side Cutters Fig. 2-3

Needle Nose Pliers Fig. 2-2




Install the e) Hood Switch with the Switch Lever underneath the Hood Lock Trigger Lever.

Make sure the Hood Switch Lever is positioned properly. If the Hood Switch is Broken RES will not function.

Route the Hood Switch f) Harness as shown.Reinstall the Spring.g)

CAUTION: Make sure that the Spring seats properly.

Needle Nose Pliers Fig. 2-5

Phillips Jewelers Screwdriver Fig. 2-4

Route the Hood Switch h) Harness below the Radiator Reinforcement Brace.

Fig. 1-6Fig. 2-6



i) Connect the 2P Hood Switch Connector to the 2P Hood Switch Harness Connector.Place the 2P Connectors j) and Wire Harness Under the Radiator Reinforcement Brace.

CAUTION: Wrap the Hood Latch in a small blanket before continuing with the Hood Switch Harness routing.

Fig. 2-7


k) Route and Secure the Hood Switch Harness as shown. (3 Wire Ties)

When installing the Wire Ties be sure to rotate their Rachet End under the Radiator Reinforcement Brace as shown.



66.4 inlbf (7.5 Nm)

70.8 inlbf (8.0 Nm)3

2

1

12

3

TIGHTEN

Torque Wrench Fig. 2-10


l) Route and secure the Hood Switch Harness as shown. (4 Wire Ties and 2 Harness Clamps)

Reinstall the Hood Lock.m)

Make sure to Torque the Bolts.

NOTE: Clean the mounting surface with VDC approvided Cleaner and Cleaning Method.



1 Glovebox Under Cover

2 PS Step Cover

3 PS Cowl Cover

4 Glovebox

5 DS Lower Dash Cover

6 Lower Steering Column Cover

7 Lower Dash Brace

8 Left Hand Lower Dash Cover

9 Center Console Lower Trim

10 Center Console Upper Trim

11 IP Panel Trim

12 IP Panel

Disconnect all Corresponding Connectors

DisassemblyOverview

3) Disassembly (PassengersArea)

Remove the Glove Box a) Under Panel.

Protect the Vehicles Interior.

Fig. 3-1

PASSENG

ERS SIDE

DRIVERS

SIDE

1

3

4

10

9

12

11

6

8

75

2



Remove the Passengers b) Step Cover.

Remove the Passengers c) Cowl Cover.

Disconnect the Dampener d) from the Glove Box.Remove the Glove Box. e)

Fig. 3-4

Nylon Panel Removal Tool Fig. 3-2




Remove the Lower Dash. f)

Release the Steering g) Columns Tilt and Telescope Lock.Dislodge the Center Clip.h)

Insert fingers into the opening of the Tilt Lever of the Steering Col-umn Under Cover to disengage 1 Claw.

CAUTION: Do not force this clip as it is very easy to break.


Fig. 3-6

Dislodge the Back Clips on i) both sides.Release the Front Clips on j) both sides.

Insert the Key into the Ignition and turn it to ON.

Turn the Steering wheel from Right to Left to access the Holes.

Use a Flat Blade Jewelers Screwdriver wrapped with Electrical Tape to release the clips.

Remove the Key from the Ignition.

Nylon Panel Removal Tool, Flat Blade Jewelers Screwdriver, Electrical Tape Fig. 3-7



Remove the Lower Dash k) Brace.

Remove 2 Nuts.

Disconnect the Vehicle Harness Clip from the Brace.

CAUTION: Sharp metal edges.

Remove the Left Hand Lower l) Dash Panel.


10mm Socket, Pliers Fig. 3-8

Remove the Center m) Consoles Left Lower Trim.




Remove the IP Panels Trim. p)

Remove the Center o) Consoles Left Upper Trim.



Nylon Panel Removal Tool Fig. 3-11Use Masking tape to protect n) the Dash.



4) V4HarnessInstallation. (DriversSide)

Locate the Vehicle Harness a) Clamp below the Steering column on the Drivers Side. Secure the White Tape b) Marker to the Vehicle Harness with 1 Wire Tie.Secure the V4 Harness and c) its Relay to the Vehicle Harness with 1 Wire Tie.

Remove 2 Screw from the IP q) Panel.Remove the IP Panel. r)

Phillips Screwdriver Fig. 3-14

White Tape Marker



Disconnect the Vehicle 14P f) Connector from the Drivers Side Junction Box.

V4ONLYRoute the two 14P V4 d) Connectors toward the Drivers Side Junction Block.Secure the V4 Harness e) to the Vehicle Harness with 1 Wire Tie.



Disconnect the Vehicle 14P k) Connector from the V5 Connector.

V4 /V5ADDONONLYCut the Wire Tie securing the i) V5 14P Connector.Cut the Wire Tie securing the j) V5 Harness to the Vehicle Harness.

Plug the V4 14P Connectors g) in between the Vehicle Connector and the Junction Box. Secure the Connectors to h) the Vehicle Harness with 1 Wire Tie.



Secure the V4 and V5 14P o) Connectors to the Vehicle Harness with 1 Wire Tie.Secure the V4 and V5 p) Harnesses to the Vehicle Brace with 1 Wire Tie.

Connect the Vehicle 14P n) Connector to the V4 14P Connector.

Route the two V4 14P l) Connectors towards the Drivers Side Junction Box.Connect the V4 14P m) Connector to the V5 14P Connector.



5) V4HarnessInstallation. (IPPanel)

GO BACK to the White Tape Marker

Route the Red Wire upward a) as shown.Secure the Red Wire and b) the Bundled up Black Wire to the Vehicle Harness with 1 Wire Tie.

Route the Red Wire and c) secure it with 1 Wire Tie.



Route the Red Wire and d) secure it with 3 Wire Ties to the Vehicle Harness.Use a Splicing Connector to e) secure the V4 Red Wire to the Wire from Pin 1 on the 40P Vehicle Connector. Bundle up the excess TVIP f) wire and secure to the Vehicle Harness with 1 Wire Tie.

6) V4HarnessInstallation. (SteeringColumn)

Disconnect the 8P IG a) Connector.Remove the Tape securing b) the 8P IG Connectors Wires and the Black 2P Connector Harness. Re-Tape the Black 2P c) Connector Wires.

Do not secure the 8P IG Connectors Wires.

Plug the V4 8P Connectors in d) between the Vehicles 8P IG Connectors.



Secure the 8P Connectors e) to Vehicle Harness with 1 Wire Tie.

CAUTION:Make sure the Connectors and Harness align properly.

Secure the V4 Harness to f) the Vehicle Harness with 1 Wire Tie.

NOTE: Verify that the Steering Column Tilts and Telescopes without interference and there is no tension on the connectors.

Route the V4 Harness g) through the Center Console.On the Drivers Side secure h) the V4 Harness to the Vehicle Brace with 1 Wire Tie. i)

7) V4harnessInstallation (PassengersSide)

Secure the V4 Harness a) to the Vehicle Braces with 3 Wire Tie.



Route the V4 Harnesss 8P b) and 20P Connectors as shown.Secure the V4 Harness to the c) Vehicle Harness with 1 Wire Tie as shown.

8) HoodSwitchHarnessRouting.(Continued)

Dislodge the Vehicle ECU.a) Remove 1 bolt.

Dislodge the Grommet. b)



Rotate the Grommet to gain c) access to the Large Rubber Nipple.

Secure the Pin Terminals d) from the Hood Switch Harness to the Wire Routing Tool with Electrical Tape.

Cut the Large Nipple.e)

NOTE:Do not cut the Small Nipple.

CAUTION: Do not damage the Pin Terminals.

Pull the Hood Switch f) Harness through the Large Hole.Remove the Tape securing g) the Hood Switch Harness to the Wire Routing Tool



Using 1/2 Piece of Butyl h) Tape fill the opening of the Grommet.Secure with Electrical Tape.i) Re-rotate the Grommet. j)

Re-fit the Grommet into the k) Firewall.

CAUTION: Makes sure that the Grommet seats into the Firewall.

Secure the Hood Switch l) Harness to the Vehicle Harness with 1 Wire Tie.



9) RESECUandGatewayECUPreparation.

Attach the RES Bracket to a) the RES ECU as shown.

Attach the Gateway ECU b) Bracket to the Gateway ECU as shown.

V4Installation 10)(GloveboxArea)

Install the a) RES ECU and Bracket.

Fig. 9-1

Fig. 9-2



Connect the b) 8P Connector to the RES ECU.Connect the 20P Connector c) to the RES ECU.

Route the V4 Harness d) securing it with 2 Wire Tie.

11)HoodSwitchPin.Disconnect the Empty a) 2P Connector from the V4 Harness.Lift up the Terminal Retainer b) Clip.

Do not Remove the Clip.

Flat Blade Jewelers Screwdriver Fig. 11-1



Insert the Terminal on the c) WHITE/BLACK Wire of the Hood Switch Harness into the Connector.Insert the Terminal on the d) GREEN/RED Wire of the Hood Switch Harness into the Connector.

VERIFY: Terminal Pins are properly inserted and do not come out.

Close the Terminal Retainer e) Clip.

Re-Connect the V4 2P f) Connectors.Wrap the 2P Connectors with g) 1/2 Piece of Foam Tape.

Re-install the Vehicles ECU. h)

GREEN/REDWHITE/BLACK

Fig. 11-2



12)V4HarnessInstallation (PassengersCowlArea).a) Connect the V4 2P

Connector, marked with Sky Blue Tape, to the Vehicles Pre-wire.

Secure both Connectors and b) the V4 Harness to the Vehicle Harness with 2 Wire Ties.

Install the c) Gateway ECU.



Connect the d) V4 5P Connector to the Gateway ECU.

Route the V4 Harness down e) towards the Passengers Cowl Area.Secure the V4 Harness to f) the Vehicle Harness with 1 Wire Tie.

Route the V4 Harness as g) shown.



Secure the V4 Harness to h) the Vehicle Harness with 1 Wire Tie.

Locate and disconnect the i) 13P Connector from the Passengers Cowl Connector Block.

Plug the V4j) 13P Connector in between the Connector Block and the Vehicle 13P Connector.



Secure the 13P Connectors k) to the Vehicle Harness with 1 Wire Tie.Secure the l) 1P Male RES Diagnostic Connector and the V4 Harness to the Vehicle Harness with 1 Wire Tie.

NOTE: Do not secure Female Connector or its wire.

13)RegistrationPreparation.Reassemble the Vehicle.a)

Note:Make sure that all Connectors are reconnected. Note: Verify that panels fit together properly, with no uneven gaps.

Verify that the Short Pin is b) Installed.

If not Install now.

10mm Socket, Phillips Screwdriver Fig. 13-1

Do Not Install



14)Registration.Open the Hood. a) Temporarily reconnect the b) Negative Battery Cable.

CAUTION: Do not touch the Positive Terminal.

Locate the 1P RES c) Diagnostic Connectors in the Passengers Side Cowl Area and connect them.

NOTE:Once connected you will have 10 minutes to complete this section, steps dx.

Close all doors. d)

Insert the key into the e) Ignition.Turn it from OFF to ON f) 5 times.

LOOK:For the Hazard Lights to flash Once.

Turn the key to the OFF g) position.

Audio AssistancePress to play/repeat

Fig. 14-1

Fig. 14-2

Fig. 14-3



Start the Engine.h) After 10 seconds stop the i) Engine.

LOOK: For the Hazard Lights to flash Once.

IFTHISPROCEDUREFAILED

The Hazard Lights flash Twice.Disconnect the V4 Harnesss 1P RES Diagnostic Connectors.

Start again from step c.

Turn the key to the ON posi-j) tion and back to the OFF position.Remove the key from the k) Ignition.

10 Seconds

Fig. 14-4

Holdup! You can actually take

a break here before you open the Drivers Door. Once you open

the door the next few steps go pretty fast so you might want to look

over them first.

Fig. 14-6

Fig. 14-5

If you are stuck at this step. Do the following:

Make sure the Vehicles Check Engine Light is not on. If so youll have to fix this.

Use the TVIP V4 EWD and Troubleshooting Guide to locate the Check Engine Signal.

Make sure the signal is getting to the RES ECU.

Check the Connector or Splicing Connector.

Make sure the Vehicles Electrical System is OK.



Open the Drivers Door.l) Using the Remote press the m) Lock Button twice within 2 Seconds.Press and hold the Lock n) Button for 4 Seconds.

Insert the Key into the o) Ignition.Remove and Insert the Key 6 p) times.Close the Drivers Door.q) Open and Close the Door 7 r) times, ending in the closed position.

This step needs to be completed in 35 seconds.

Look for the Immobilizer LED s) to turn on for 1 Second and go off.After 1 Second look for the t) Immobilizer LED to come back on and stay on.Remove the key from the u) Ignition. Look for the Immobilizer LED v) to turn off.

IFTHISPROCEDUREFAILEDThe Immobilizer LED does not Light properly.

Disconnect the V4 Harnesss 1P RES Diagnostic Connectors.


PRESS 2 Seconds

4 Seconds

PRESS

HOLD

Fig. 14-7

Fig. 14-8

Fig. 14-9

1 Second

Stays O

nTurns O

ff1 S

econd



Exit the vehicle.w) Close the Hood.x) Look for the Hazards to flash y) twice.

IFTHISPROCEDUREFAILED

The Hazard Lights flash Three Times.

Disconnect the V4 Harnesss 1P RES Diagnostic Connectors.


After a successful Registra-z) tion Disconnect the 1P RES Diagnostic Connectors.Using Electrical Tape secure aa) the Female Connector and Harness to the Vehicle Harness.

Fig. 14-10

Fig. 14-11



15)TagsandLabels.

For US Vehicles us the English Tags and Labels, and discard the Spanish Tags and Labels.

For Mexico Vehicles us the Span- ish Tags and Labels, and discard the English Tags and Labels.

Using VDC approved cleaner a) and cleaning method, clean the area indicated in the Engine Compartment.Attach the Engine Room b) Warning Label as shown.

CAUTION: Do not touch the adhesive surface.

Using VDC approved cleaner c) and cleaning method, clean the indicated area on the key.Use a piece of Clear Tape to d) lift the label off its protective backing.


Attach the Key Label as e) shown.

Attach the Key Tag.f)

REPEAT: steps c f with the other Key.

Use Household Glass g) Cleaner to clean the inside of the Front Door Windows.Use a piece of Clear Tape h) to lift the Label from the protective backing.


Attach the Label as shown.i)

NOTE:Make sure to Align according to Etching or Other Label.

REPEAT: steps g i with the other Window.

Fig. 15-1

Clear Tape Fig. 15-2

HOW T

O ALIG

N TO T

HE ET

CHING

10 mm

15 mm

Clear Tape Fig. 15-3

HOW T

O ALIG

N TO O

THER

LABE

LS



16)CompletetheInstallation.Finish reassembling the a) Vehicle.

VERIFY: that panels fit together properly, with no uneven gaps.

VERIFY: that all Connectors are plugged in.

Position the Negative Battery b) Cable at the original factory position.

Tighten the Nut to 36 inlbf (4.07 Nm)

CAUTION: Do not touch the positive terminal.

Clean up and Remove trash.c) Sealed in its protective bag, d) place the Owners Manual in the Glovebox.

Reset the power windows.e) Turn the ignition ON.

Lower the Windows halfway.

Pull up on the Power Window Switches until the windows close.

Continue to hold up on the switches for a minimum of 1 Second.

Reset the Moon Roof.f) Turn the ignition ON.

Open the Moon Roof halfway.

Push and hold the Moon Roof Switch to close until the Moon Roof closes.

Continue to hold the switch for a minimum of 1 Second.

Torque Wrench Fig. 16-2

Fig. 16-1

TOYOTA COROLLA 2009 TVIP V4CHECKLIST these points MUST be checked to ensure a quality installation. REMOTE ENGINE STARTER (RES)


AccessoryFunctionChecks

Close the hood, place the shift lever in the P (parking) position, set the parking brake, remove the key from the igni-tion, close all doors, and exit the vehicle.

1 Press the remote controls lock button twice within 2 seconds, then press and hold the lock button 3 seconds.

The hazard lights flash after 3 seconds. The engine starts. The hazard lights flash repeatedly for 20 seconds.

2 Press the remote controls unlock button. The engine stops. The hazard lights flash twice.

3 Start the Vehicle again using the remote. With the engine running, press and hold the remote controls lock button 2 seconds.

Refer to Step 1. The engine stops. The hazard lights flash once.

4 Start the Vehicle again using the remote. Unlock the doors with the key.


Enter the vehicle and close all doors.

5 Start the Vehicle again using the remote. With the engine running, manually unlock any door with the inside lock switch.

Refer to Step 1. The engine stops. The hazard lights flash once. The security alarm triggers. (if equipped)

6 Start the Vehicle again using the remote. With the engine running, push down on the accelera-tor until the engine speed exceeds 3000 RPMs.


7 Start the Vehicle again using the remote. With the engine running, push on the foot brake.


8 Start the Vehicle again using the remote. With the engine running, insert the key into the igni-tion switch.

Refer to Step 1. The engine stops. The hazard lights flash once

9 Move the shift lever out of P (Park). Attempt to start the Vehicle using the remote.

The engine does not start.

10 Start the Vehicle again using the remote. With the engine running, pull the hood release handle.

Refer to Step 1. The engine stops. The hazard lights flash once. The security alarm triggers. (if equipped)



VehicleFunctionCheck

Function Function

Head Light ABS Light (if equipped) If the warning light remains on, it may indicate a system malfunction.

High Beams Rear Wiper/Washer (if equipped) Turn Signal Lights Clock (if equipped) Tail Lights Accessory Power Socket (if equipped) Stop Lights Starter Backup Lights Audio/Video (if equipped) Hazard Lights Power Sliding Door (if equipped) Marker Lights Convenience Memory Settings (if equipped) Dome/Courtesy Lights Heated Seats (if equipped) Panel/Switch Illumination Massage Seats (if equipped) Accessory Controls/Illumination

(if equipped) Rear Window Defogger (if equipped)

Key Sensor Buzzer Power Side Mirrors (if equipped) Fog Lights (if equipped) Side Mirror Defogger (if equipped) Daytime Running Lights (if equipped) Front Windshield Defogger (if equipped) Trunk/Tailgate/Bed Lights (if equipped) Navigation System (if equipped) Glove Box Light (if equipped) I Rear Sunshade (if equipped) Cruise Control Light (if equipped) Steering Wheel Audio Control (if equipped) Seat Belt Warning Light

If the warning light remains on, it may indi-cate a system malfunction.

Steering Wheel Column Adjusts Without Interference



Function Function

Air Bag Warning Light If the warning light remains on, it may indicate a system malfunction.

Lamp Failure Sensor If the warning light remains on, it may indicate a sys-tem malfunction.

Track/Skid Control Light (if equipped) If the warning light remains on, it may indicate a system malfunction.

Front Wiper/Washer

HVAC Hood Latch Release Power Locks (if equipped) Passenger Air Bag Switch (if equipped) Power Windows (if equipped) Rollover Side Curtain Air Bag Switch (RSCA) (if

equipped)

Power Seats (if equipped) Tire Pressure Monitoring System (TPMS).Prior to TPMS activation and Pre-delivery Service (PDS) of the Vehicle the TPMS light will blink when IG is turned on.

After TPMS activation and PDS of the Vehicle the TPMS light will illuminate for a few seconds and go off when IG is turned on.

Horn

Gauges

RemovetheshortpinafterFunctioncheck. Check with your Port/Dealer to see if this step is necessary.

TOYOTA COROLLA 2009 TVIP V4ADDENDUM I REMOTE ENGINE STARTER (RES)


Button 38: Button 83: Button 39: Button 34: Button 79: Button 36: Button 30: Button 32: Button 33: Button 29: Button 80: Button 40: Button 41: Button 86: Button 43: Button 87: Button 85: Button 44: Button 45: Button 46: Button 47: Button 48: Button 76: Button 77: Button 51: Button 54: Button 55: Button 56: Button 68: Button 82: Button 60: Button 61: Button 62: Button 70: Button 71: Button 72: Button 73: Button 64: Button 65: Button 78: Button 69:

TOYOTA COROLLA 2009– TVIP V4 PREPARATION...

Documents

Transcript of TOYOTA COROLLA 2009– TVIP V4 PREPARATION...