Touchscreen thermostat programming guide (8259)€¦ · Heating Schedule Options. 6 Tap the button...
2
Touchscreen thermostat programming guide (8259) www.comfortzone.co [email protected] Watch the wiring guide video on our website °C Power button Clock button/Backlight Menu button Down button Up button 1 To access advanced settings switch the unit off by tapping the button. 2 Then press and hold both the and button. 3 Tap the button to switch to Sensor mode (2SEN) and set to OUT Before you start (Advanced settings) 8259 has some advanced settings which must be configured before programming. These include Sensor Setup, Frost Protection & Heating Schedule Options. 6 Tap the button to set your program days. 7 Tap and to set the program days. 8 Program options include: 9 Switch off to save your settings using the button. • Seven days same • Five days & weekend • Six days same & 1 separate day • Program off Heating schedule options Set the time and date Your heating schedule can be configured to suit most lifestyles. The options are Mon – Fri (1-5) the same with Sat – Sun (6-7) separate. Mon – Sat (1-6) the same with Sun (7) separate and All Days (1-7) the same. You can also switch off the heating schedule if you require. 1-5 days settings have 3 comfort periods. 6-7 day settings has 1 comfort period. Sensor mode The 8259 has three sensor settings. Air Sensor (IN), Floor Sensor (OUT) and Air Sensor with Floor Limit (All). We recommend Floor Sensor (OUT) for the most accurate control. Air Sensor (IN) Floor Sensor (OUT) Air Sensor with Floor Limit (All) °C °C °C 4 Tap the button until you see Frost protection mode (5LrP - pictured left). 5 Set this to “On” using the and arrows. °C Frost protection When set to ON, the built in frost protection feature will ensure the temperature of your substrate never dips below 10 o c. This protects against frozen substrates and ensures economical heat up times. Up Manual control mode Period 1 Down Program mode indicator Power Menu button Period 4 Period 2 Period 5 Heating on Period 3 Period 6 Clock Button 1 Tap the button to switch unit on. 2 The backlight will fade after around 10 seconds. 3 Tap the button to switch it back on at any point. 4 Press and hold the button for around 7 seconds or until the minutes begin to flash. 5 Use the and arrows to select the correct minute. 6 Tap the button to switch to hour and use and to select the correct hour. 7 Tap the button again to edit the day. 8 Use the and arrows to select the correct day number: 1 = Mon 7 = Sun.
Transcript of Touchscreen thermostat programming guide (8259)€¦ · Heating Schedule Options. 6 Tap the button...
Touchscreen thermostat programming guide (8259)
Watch the wiring guide video on our website
1
5432
67
°C
°C
°C
°C
Power button
Clock button/Backlight
Menu button
Down button
Up button
1 Toaccessadvancedsettingsswitchtheunitoffbytappingthe button.
2 Then press and hold both the and button.
3 Tap the button to switch to Sensor mode (2SEN) and set to OUT
Before you start (Advanced settings)8259hassomeadvancedsettingswhichmustbeconfiguredbeforeprogramming. These include Sensor Setup, Frost Protection & Heating Schedule Options.
6 Tapthebuttontosetyourprogramdays.
7 Tap and to set the program days.
8 Program options include:
9 Switchofftosaveyoursettingsusingthe button.
• Sevendayssame• Fivedays&weekend• Sixdayssame&1separateday• Programoff
Heating schedule options
Set the time and date
Yourheatingschedulecanbeconfiguredtosuitmostlifestyles.TheoptionsareMon–Fri(1-5)thesamewithSat–Sun(6-7)separate.Mon–Sat(1-6)thesamewithSun(7)separateandAllDays(1-7)thesame.Youcanalsoswitchofftheheatingscheduleifyourequire.1-5dayssettingshave3comfortperiods.6-7daysettingshas1comfortperiod.
Sensor modeThe8259hasthreesensorsettings.AirSensor(IN),FloorSensor(OUT)andAirSensorwithFloorLimit(All).WerecommendFloorSensor(OUT)forthemost accurate control.
AirSensor(IN) Floor Sensor (OUT) AirSensorwithFloorLimit(All)
°C °C
°C
°C
°C°C
°C°C°C
1
5432
67
°C
4 TapthebuttonuntilyouseeFrostprotectionmode(5LrP-picturedleft).
5 Set this to “On” using the and arrows.
°C
Frost protectionWhensettoON,thebuiltinfrostprotectionfeaturewillensurethetemperatureofyoursubstrateneverdipsbelow10oc. This protects against frozensubstratesandensureseconomicalheatuptimes.
Up
Manual control mode
Period1
Down
Program mode indicator
Power
Menu button
Period 4
Period 2
Period 5
Heating on
Period3
Period6
Clock Button
1 Tap the button to switch unit on.
2 Thebacklightwillfadeafteraround10seconds.
3 Tapthebuttontoswitchitbackonatanypoint.
4 Pressandholdthebuttonforaround7secondsoruntiltheminutesbegintoflash.
5 Use the and arrows to select the correct minute.
6 Tap the button to switch to hour and use and to select the correct hour.
7 Tapthebuttonagaintoedittheday.
8 Usetheandarrowstoselectthecorrectdaynumber:1=Mon7=Sun.
Watch the wiring guide video on our website
Manual heating mode
Creating your heating schedule
1 Tap button to switch the unit into Schedule mode.
2 You will see both the and (Period1-6)symbolsdisplayed.
3 Pressandholdfor7secondstoedityourschedule.
4 Firstly,setthestarttimefor(period1)usingtheupand down buttons.
5 TaptosaveyourstarttimeandsettheComfortTemperaturetobetween200Cand270C.
6 Tap to advance to (period 2) and select the desired time using and .
7 TaptosaveyourstarttimeandsettheEcoTemperaturebetween180Cand200C.
8 Taptoadvanceto(period3)andselectthedesiredtimeusing and .
9 TaptosaveyourstarttimeandsettheComfortTemperaturetobetween200Cand270C.
10 Tap to advance to (period 4) and select the desired time using and .
11 TaptosaveyourstarttimeandsettheEcoTemperaturebetween180Cand200C.
12 Tap to advance to (period 5) and select the desired time using and .
13 TaptosaveyourstarttimeandsettheComfortTemperaturetobetween200Cand270C.
14 Taptoadvanceto(period6)andselectthedesiredtimeusing and .
1 YoucanswitchbetweenManualmodeandyourcustomSchedulebytapping.
2 Whenin(Manualcontrolmode),setatargettemperaturemanuallyusingand.
3 Whenthetargettemperatureissetabovetheambienttemperature,youwillseethe(Heatingon)symbolbelowthetargettemperature.Youmayalsoheara‘click’.
15 TaptosaveyourstarttimeandsettheEcoTemperaturebetween180Cand200C.
16 Nowyouhaveasetschedulefor5days.Taptosetyourweekend heating.
17 Selectalaterstarttimeifyoulikealiein.Thistimewillapplytobothdays.
18 TaptosaveyourstarttimeandsettheComfortTemperaturebetween200Cand270C.
19 Taptosaveyourtemperatureandadvanceto
(Period 2).
20 Set the desired start time and set the Eco Temperature between 180Cand200C.
21 Youshouldnowhaveacomplete7dayheatingschedule!
22 Simplytap(Power)toactivateyourscheduleandyou’redone.
Taptheiconatanytimetoswitchonthebacklight.Itwillturnoffautomaticallyafterasetperiodoftime.
Presstoswitchtheunitoffthenpressandholdandtogether.PresstoscrolltoAFAC.Holduntil“---”isdisplayed.Nowpressthenswitchofftocompletethefactoryreset.
Press and hold the and to lock the screen, press and hold againtounlock.Thisfeatureisusefulifthethermostatisinstalledinanenvironment where access to the heating setting must be restricted.
ER0Damaged or disconnected ambient temperature sensor (internal). This errorusuallyrequiresareplacementthermostat.
ER1Damagedordisconnectedfloorsensorprobe(external).Werecommendthatyoucontactyourelectriciantoisolatetheelectricitysupplyandcheckthesensorisworkingandconnected.
Screen lock (Child lock)
Error codes
Backlight control
Factory reset
Touchscreen thermostat programming guide (8259)
