Toshiba D-r160-Sb Dvd Video Recorder
description
Transcript of Toshiba D-r160-Sb Dvd Video Recorder
SERVICE MANUAL
TOSHIBA CORPORATION 2006
The above model is classified as a green product (*1), as indicated by the underlined serialnumber. This Service Manual describes replacement parts for the green product. Whenrepairing this green product, use the part(s) described in this manual and lead-free solder (*2).
For (*1) and (*2), see the next page.
FILE NO. 810-200617GR
DVD Video Recorder
D-R160SB
Published in Japan, Mar. 2006 GREEN
®
(*1) GREEN PRODUCT PROCUREMENTThe EC is actively promoting the WEEE & RoHS Directives that define standards for recyclingand reuse of Waste Electrical and Electronic Equipment and for the Restriction of the use ofcertain Hazardous Substances. From July 1, 2006, the RoHS Directive will prohibit anymarketing of new products containing the restricted substances.
Increasing attention is given to issues related to the global environmental. Toshiba Corporationrecognizes environmental protection as a key management tasks, and is doing its utmost toenhance and improve the quality and scope of its environmental activities. In line with this,Toshiba proactively promotes Green Procurement, and seeks to purchase and use products,parts and materials that have low environmental impacts.
Green procurement of parts is not only confined to manufacture. The same green parts used inmanufacture must also be used as replacement parts.
(*2) LEAD-FREE SOLDERThis product is manufactured using lead-free solder as a part of a movement within the consumerproducts industry at large to be environmentally responsible. Lead-free solder must be used in theservicing and repair of this product.
WARNINGThis product is manufactured using lead free solder.
DO NOT USE LEAD BASED SOLDER TO REPAIR THIS PRODUCT !
The melting temperature of lead-free solder is higher than that of leaded solder by 86°F to 104°F(30°C to 40°C). Use of a soldering iron designed for lead-based solders to repair product madewith lead-free solder may result in damage to the component and or BOARD being soldered.Great care should be made to ensure high-quality soldering when servicing this product —especially when soldering large components, through-hole pins, and on BOARDs — as the levelof heat required to melt lead-free solder is high.
IMPORTANT SAFETY NOTICE
Proper service and repair is important to the safe, reliable operation of all TOSHIBA Equipment. The service procedures recommended by TOSHIBA and described in this service manual are effective methods of performing service operations. Some of these service special tools should be used when and as recommended.
It is important to note that this service manual contains various CAUTIONS and NOTICES which should be carefully read in order to minimize the risk of personal injury to service personnel. The possibility exists that improper service methods may damage the equipment. It also is important to understand that these CAUTIONS and NOTICES ARE NOT EXHAUSTIVE. TOSHIBA could not possibly know, evaluate and advice the service trade of all conceivable ways in which service might be done or of the possible hazardous consequences of each way. Consequently, TOSHIBA has not undertaken any such broad evaluation. Accordingly, a servicer who uses a service procedure or tool which is not recommended by TOSHIBA must first use all precautions thoroughly so that neither his safety nor the safe operation of the equipment will be jeopardized by the service method selected.
TABLE OF CONTENTS
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1-1Laser Beam Safety Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2-1Important Safety Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3-1Standard Notes for Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4-1Cabinet Disassembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5-1How to Initialize the DVD Recorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6-1Firmware Renewal Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7-1Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8-1Function Indicator Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9-1Block Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10-1Schematic Diagrams / BOARD’s and Test Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11-1Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12-1Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13-1System Control Timing Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14-1IC Pin Function Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-15-1Lead Identifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-16-1Exploded Views . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-17-1Mechanical Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-18-1Electrical Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-19-1
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
1-1-1 E7B71SP
SPECIFICATIONS
General
SystemDVD-Video, DVD-R/RW, CD-DA, CD-R/RW,VCD, SVCD
Power requirements220–240V ± 10%, 50Hz ± 0.5%
Power consumption25W (standby: 4.5W)
Weight2.4kg
Dimensions (width x height x depth)435 x 66 x 244mm
Operating temperature5ºC to 40ºC
Operating humidityLess than 80% (no condensation)
TV formatPAL - I
Recording
Recording formatVideo Recording format (DVD-RW only),Video format (DVD-RW, DVD-R)
Recordable discsDVD-Rewritable, DVD-Recordable
Video recording formatSampling frequency : 13.5MHzCompression format : MPEG
Audio recording formatSampling frequency : 48kHzCompression format : Dolby Digital
Tuner
Receivable channelsIRA - E69
Input/Output
Front Panel : (AV4)
Video inputOne RCA connectorInput level : 1Vp-p (75 Ω)
S-Video inputOne Mini DIN 4-pin jackInput level : Y (Iuminance) 1Vp-p (75 Ω) C (colour) 300mVp-p (75 Ω)
Audio inputTwo RCA connectorsInput level : 2Vrms (Input impedance: more than
10k Ω)
Rear Panel :
VHF/UHF antenna input/output terminalVHF/UHF set 75 Ω
Audio input /outputTwo 21-pin scart jack (AV1, AV2)
Video input /outputTwo 21-pin scart jack (AV1, AV2)Input /output level : 1Vp-p (75 Ω) each
S-Video input (AV3) /outputTwo Mini DIN 4-pin jacksInput /output level : Y (Iuminance) 1Vp-p (75 Ω) C (colour) 300mVp-p (75 Ω)
Component video outputThree RCA connectorsOutput level : Y: 1.0Vp-p (75 Ω) P B/CB, P R /CR : 0.7Vp-p (75Ω) each
Audio inputTwo RCA connectors (AV3)Input level : 2Vrms (Input impedance: more than
10k Ω)
Analogue audio outputTwo RCA connectorsOutput level : 2Vrms (Output impedance: Ω)
Digital audio outputOne Coaxial pin jackOutput level : 500mVp-p (75 Ω)
NoteThe specifications and design of this product are subject to change without notice.
680
1-2-1 R3PLSP
LASER BEAM SAFETY PRECAUTIONS
This DVD player uses a pickup that emits a laser beam.
The laser beam is emitted from the location shown in the figure. When checking the laser diode, be sure to keep your eyes at least 30 cm away from the pickup lens when the diode is turned on. Do not look directly at the laser beam.
CAUTION: Use of controls and adjustments, or doing procedures other than those specified herein, may result in hazardous radiation exposure.
Location: Inside Top of DVD mechanism.
Do not look directly at the laser beam coming from the pickup or allow it to strike against your skin.
Drive Mechanism Assembly
Laser Beam Radiation
Laser Pickup
Turntable
1-3-1 DVD_SFNP
IMPORTANT SAFETY PRECAUTIONS
Product Safety NoticeSome electrical and mechanical parts have specialsafety-related characteristics which are often not evi-dent from visual inspection, nor can the protectionthey give necessarily be obtained by replacing themwith components rated for higher voltage, wattage,etc. Parts that have special safety characteristics areidentified by a ! on schematics and in parts lists. Useof a substitute replacement that does not have thesame safety characteristics as the recommendedreplacement part might create shock, fire, and/or otherhazards. The Product’s Safety is under review continu-ously and new instructions are issued wheneverappropriate. Prior to shipment from the factory, ourproducts are carefully inspected to confirm with therecognized product safety and electrical codes of thecountries in which they are to be sold. However, inorder to maintain such compliance, it is equally impor-tant to implement the following precautions when a setis being serviced.
Precautions during ServicingA. Parts identified by the ! symbol are critical for
safety. Replace only with part number specified.
B. In addition to safety, other parts and assembliesare specified for conformance with regulationsapplying to spurious radiation. These must also bereplaced only with specified replacements.Examples: RF converters, RF cables, noise block-ing capacitors, and noise blocking filters, etc.
C. Use specified internal wiring. Note especially:
1)Wires covered with PVC tubing2)Double insulated wires3)High voltage leads
D. Use specified insulating materials for hazardouslive parts. Note especially:
1)Insulation tape2)PVC tubing 3)Spacers4)Insulators for transistors
E. When replacing AC primary side components(transformers, power cord, etc.), wrap ends ofwires securely about the terminals before solder-ing.
F. Observe that the wires do not contact heat produc-ing parts (heatsinks, oxide metal film resistors, fus-ible resistors, etc.).
G. Check that replaced wires do not contact sharpedges or pointed parts.
H. When a power cord has been replaced, check that5 - 6 kg of force in any direction will not loosen it.
I. Also check areas surrounding repaired locations.
J. Be careful that foreign objects (screws, solderdroplets, etc.) do not remain inside the set.
K. Crimp type wire connectorThe power transformer uses crimp type connectorswhich connect the power cord and the primary sideof the transformer. When replacing the transformer,follow these steps carefully and precisely to pre-vent shock hazards.Replacement procedure
1)Remove the old connector by cutting the wires at apoint close to the connector.Important: Do not re-use a connector. (Discard it.)
2)Strip about 15 mm of the insulation from the endsof the wires. If the wires are stranded, twist thestrands to avoid frayed conductors.
3)Align the lengths of the wires to be connected.Insert the wires fully into the connector.
4)Use a crimping tool to crimp the metal sleeve at itscenter. Be sure to crimp fully to the complete clo-sure of the tool.
L. When connecting or disconnecting the internalconnectors, first, disconnect the AC plug from theAC outlet.
1-3-2 DVD_SFNP
Chassis or Secondary Conductor
Primary Circuit
d' d
AC Voltmeter(High Impedance)
Exposed Accessible Part
B One side of Power Cord Plug Prongs
Z
Safety Check after ServicingExamine the area surrounding the repaired locationfor damage or deterioration. Observe that screws,parts, and wires have been returned to their originalpositions. Afterwards, do the following tests and con-firm the specified values to verify compliance withsafety standards.
1. Clearance DistanceWhen replacing primary circuit components, confirmspecified clearance distance (d) and (d’) between sol-dered terminals, and between terminals and surround-ing metallic parts. (See Fig. 1)
Table 1 : Ratings for selected area
Note: This table is unofficial and for reference only. Be sure to confirm the precise values.
2. Leakage Current TestConfirm the specified (or lower) leakage currentbetween B (earth ground, power cord plug prongs)and externally exposed accessible parts (RF termi-nals, antenna terminals, video and audio input andoutput terminals, microphone jacks, earphone jacks,etc.) is lower than or equal to the specified value in thetable below.
Measuring Method (Power ON) :Insert load Z between B (earth ground, power cordplug prongs) and exposed accessible parts. Use anAC voltmeter to measure across the terminals of loadZ. See Fig. 2 and the following table.
AC Line Voltage Clearance Distance (d), (d’)
220 to 240 V≥ 3 mm(d)≥ 6 mm(d’)
Table 2: Leakage current ratings for selected areas
Note: This table is unofficial and for reference only. Be sure to confirm the precise values.
AC Line Voltage Load Z Leakage Current (i) One side of power cord plug prongs (B) to:
220 to 240 V
2kΩ RES. Connected in
parallel
i≤0.7mA AC Peaki≤2mA DC
RF orAntenna terminals
50kΩ RES. Connected in
parallel
i≤0.7mA AC Peaki≤2mA DC A/V Input, Output
Fig. 1
Fig. 2
1-4-1 DVDN_SN
STANDARD NOTES FOR SERVICING
Circuit Board Indications1. The output pin of the 3 pin Regulator ICs is
indicated as shown.
2. For other ICs, pin 1 and every fifth pin are indicated as shown.
3. The 1st pin of every male connector is indicated as shown.
Instructions for Connectors1. When you connect or disconnect the FFC (Flexible
Foil Connector) cable, be sure to first disconnect the AC cord.
2. FFC (Flexible Foil Connector) cable should be inserted parallel into the connector, not at an angle.
Pb (Lead) Free SolderWhen soldering, be sure to use the Pb free solder.
How to Remove / Install Flat Pack-IC
1. Removal
With Hot-Air Flat Pack-IC Desoldering Machine:
1. Prepare the hot-air flat pack-IC desoldering machine, then apply hot air to the Flat Pack-IC (about 5 to 6 seconds). (Fig. S-1-1)
2. Remove the flat pack-IC with tweezers while applying the hot air.
3. Bottom of the flat pack-IC is fixed with glue to the BOARD; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6)
4. Release the flat pack-IC from the BOARD using tweezers. (Fig. S-1-6)
CAUTION:
1. The Flat Pack-IC shape may differ by models. Use an appropriate hot-air flat pack-IC desoldering machine, whose shape matches that of the Flat Pack-IC.
2. Do not supply hot air to the chip parts around the flat pack-IC for over 6 seconds because damage to the chip parts may occur. Put masking tape around the flat pack-IC to protect other parts from damage. (Fig. S-1-2)
NOTE: BOARD MEANS PRINTED CIRCUIT BOARD.
Top View
Out In
Bottom ViewInput
5
10
Pin 1
Pin 1
FFC Cable
Connector
BOARD
* Be careful to avoid a short circuit.
Fig. S-1-1
1-4-2 DVDN_SN
3. The flat pack-IC on the BOARD is affixed with glue, so be careful not to break or damage the foil of each pin or the solder lands under the IC when removing it.
With Soldering Iron:
1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3)
2. Lift each lead of the flat pack-IC upward one by one, using a sharp pin or wire to which solder will not adhere (iron wire). When heating the pins, use a fine tip soldering iron or a hot air desoldering machine. (Fig. S-1-4)
3. Bottom of the flat pack-IC is fixed with glue to the BOARD; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6)
4. Release the flat pack-IC from the BOARD using tweezers. (Fig. S-1-6)
Hot-airFlat Pack-ICDesolderingMachine
BOARD
Flat Pack-IC
Tweezers
MaskingTape
Fig. S-1-2
Flat Pack-IC Desoldering Braid
Soldering Iron
Fig. S-1-3
Fine TipSoldering Iron
SharpPin
Fig. S-1-4
1-4-3 DVDN_SN
With Iron Wire:
1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3)
2. Affix the wire to a workbench or solid mounting point, as shown in Fig. S-1-5.
3. While heating the pins using a fine tip soldering iron or hot air blower, pull up the wire as the solder melts so as to lift the IC leads from the BOARD contact pads as shown in Fig. S-1-5.
4. Bottom of the flat pack-IC is fixed with glue to the BOARD; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6)
5. Release the flat pack-IC from the BOARD using tweezers. (Fig. S-1-6)
Note: When using a soldering iron, care must be taken to ensure that the flat pack-IC is not being held by glue. When the flat pack-IC is removed from the BOARD, handle it gently because it may be damaged if force is applied.
2. Installation1. Using desoldering braid, remove the solder from
the foil of each pin of the flat pack-IC on the BOARD so you can install a replacement flat pack-IC more easily.
2. The “” mark on the flat pack-IC indicates pin 1. (See Fig. S-1-7.) Be sure this mark matches the 1 on the BOARD when positioning for installation. Then presolder the four corners of the flat pack-IC. (See Fig. S-1-8.)
3. Solder all pins of the flat pack-IC. Be sure that none of the pins have solder bridges.
To Solid Mounting Point
Soldering Iron
Iron Wire
or
Hot Air Blower
Fig. S-1-5
Fine TipSoldering IronBOARD
Flat Pack-ICTweezers
Fig. S-1-6
Example :
Pin 1 of the Flat Pack-ICis indicated by a " " mark. Fig. S-1-7
Presolder
BOARD
Flat Pack-IC
Fig. S-1-8
1-4-4 DVDN_SN
Instructions for Handling Semi-conductorsElectrostatic breakdown of the semi-conductors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work.
1. Ground for Human Body
Be sure to wear a grounding band (1 MΩ) that is properly grounded to remove any static electricity that may be charged on the body.
2. Ground for Workbench
Be sure to place a conductive sheet or copper plate with proper grounding (1 MΩ) on the workbench or other surface, where the semi-conductors are to be placed. Because the static electricity charge on clothing will not escape through the body grounding band, be careful to avoid contacting semi-conductors with your clothing.
<Incorrect>
BOARD
Grounding Band
Conductive Sheet orCopper Plate
1MΩ
1MΩ
<Correct>
BOARD
1-5-1 E7B71DC
CABINET DISASSEMBLY INSTRUCTIONS
1. Disassembly FlowchartThis flowchart indicates the disassembly steps to gain access to item(s) to be serviced. When reassembling, follow the steps in reverse order. Bend, route, and dress the cables as they were originally.
2. Disassembly Method
Note:
(1) Identification (location) No. of parts in the figures
(2) Name of the part
(3) Figure Number for reference
(4) Identification of parts to be removed, unhooked, unlocked, released, unplugged, unclamped, or desoldered. P = Spring, L = Locking Tab, S = Screw, CN = Connector* = Unhook, Unlock, Release, Unplug, or Desoldere.g. 2(S-2) = two Screws (S-2), 2(L-2) = two Locking Tabs (L-2)
(5) Refer to “Reference Notes.”
Reference Notes1. CAUTION 1: Locking Tabs (L-1) and (L-2) are
fragile. Be careful not to break them.
NOTE: BOARD MEANS PRINTED CIRCUIT BOARD.
ID/Loc. No.
Part
Removal
Fig.No.
Remove/*Unhook/Unlock/Release/Unplug/Desolder
Note
[1] COVER TOP D1 8(S-1) ---
[2] PANEL FRONT D2 *6(L-1), *3(L-2) 1
[3]
DVD MECHANISM & DVD MAIN BOARD ASSEMBLY
D34(S-2), *CN101, *CN701, LOCKING CARD SPACERS
---
[4] BOARD SWITCH D4 (S-3), Desolder ---
[5] BOARD HOLDER D4 2(S-4) ---
[6]BOARD POWER SUPPLY
D4 2(S-5), *CN1152 ---
[7] POWER HOLDER D4 (S-6) ---
[8] FAN COVER D5 2(S-7) ---
[9] FAN D5 FAN EARTH, *CN1601 ---
[1] COVER TOP
[2] PANEL FRONT
[9] FAN
[8] FAN COVER
[3] DVD MECHANISM & DVD MAIN BOARD ASSEMBLY
[4] BOARD SWITCH
[5] BOARD HOLDER
[6] BOARD POWER SUPPLY
[7] POWER HOLDER
[10] PANEL REAR
[11] BOARD POWER
[12] BOARD JACK [13] BOARD AFV
[10] PANEL REAR D5 (S-8), 6(S-9), 2(S-10) ---
[11] BOARD POWER D6 3(S-11) ---
[12] BOARD JACK D6 Desolder ---
[13] BOARD AFV D6 Desolder ---
↓(1)
↓(2)
↓(3)
↓(4)
↓(5)
ID/Loc. No.
Part
Removal
Fig.No.
Remove/*Unhook/Unlock/Release/Unplug/Desolder
Note
[1] COVER TOP
(S-1)(S-1)
(S-1)
Fig. D1
1-5-2 E7B71DC
(L-1)
(L-1)
(L-2)
(L-1)
Fig. D2
[2] PANEL FRONT
(S-2) (S-2)
Fig. D3
CN101
CN701
[3] DVD MECHANISM & DVD MAIN BOARD ASSEMBLY
LOCKINGCARDSPACER
LOCKINGCARDSPACER
(S-4)
Desolder
(S-3)
CN1152
(S-5)
(S-6)
[4] BOARD SWITCH
[5] BOARD HOLDER
[6] BOARD POWER SUPPLY
[7] POWER HOLDER
Fig. D4
Fig. D5
(S-9)(S-10)
FAN EARTH
CN1601
(S-8)
(S-7)
[9] FAN
[8] FAN COVER
[10] PANEL REAR
Fig. D6
(S-11)
(S-11)
Desolder
Desolder[11] BOARD POWER
[12] BOARD JACK
[13] BOARD AFV
1-5-3 E7B71DC
3. How to Eject ManuallyNote: When rotating the gear, be careful not to damage the gear.
1. Remove the COVER TOP.
2. Rotate the gear in the direction of the arrow manually as shown below until the tray descends.
3. Pull the tray out manually and remove a disc.
A
View for A
Rotate this gear in the direction of the arrow
1-6-1 E7B71INT
HOW TO INITIALIZE THE DVD RECORDER
To put the program back at the factory-default, initialize the DVD recorder as the following procedure.
1. Turn the DVD recorder on.
2. Confirm that no disc is loaded or that the disc tray is open. To put the DVD recorder into the Version display mode, press [INSTANT SKIP], [1], [2], and [3] buttons on the remote control in the order. Fig. a appears on the screen.
3. Press [ENTER] button, then the DVD recorder starts initializing. When the initializing is completed, the DVD recorder exits the Version display mode and turns off the power automatically.
* To move into the Normal mode from the Version display mode, press [RETURN] button on the remote control instead of [ENTER] button.
* When [ ] button is pressed before [ENTER] button is pressed, the DVD recorder exits the Version display mode, then the power turns off.
MODEL NAME : *******
FE VERSION :BE VERSION : TT VERSION :
LD ADJUSTMENT : DISC ADJUSTMENT :
DEFAULT SETTING : ENTEREXIT : RETURN
OKOK
R30_011_00tR3T32684U2BT30025FSP
*1: "*******" differs depending on the models.*2: Firmware Version differs depending on the models, and this indication is one example.
Fig. a Version Display Mode Screen
F/W VERSION DISP
1-7-1 E7B71FW
FIRMWARE RENEWAL MODE
1. Turn the power on and remove the disc on the tray.
2. To put the DVD recorder into version up mode, press [INSTANT SKIP], [6], [5], and [4] buttons on the remote control unit in the order. Then the tray will open automatically.Fig. a appears on the screen and Fig. b appears on the VFD.
3. Load the disc for version up.Fig. c appears on the screen. The file on the top is highlighted as the default.When there is only one file to exist, Step 4 will start automatically.
4. Select the firmware version pressing arrow buttons, then press [ENTER].Fig. d appears on the screen and Fig. e appears on the VFD. The DVD recorder starts updating.
About VFD indication of Fig. e:
1) When Fig. d is displayed on the screen, “F-UP” is displayed on the VFD.
2) When “Firmware Updating... XX% Complete.” is displayed on the screen, “32684” is displayed on the VFD.
The appearance shown in (*1) of Fig. d is described as follows.
5. After updating is finished, the tray opens automatically.At this time, no button is available.
6. Pull out the AC code once, then insert it again.
Fig. a Version Up Mode Screen
* Firmware Version differs depending on the models, and this indication is one example.
CurrentF/W version is displayed.
Firm Update Mode
Please insert a disc.
ver. R3T32684U2B
Fig. b VFD in Version Up Mode
Fig. c Update Disc Screen
* Firmware Version differs depending on the models, and this indication is one example.
Disc name is displayed.
Firm Update Mode ver. R3T32684U2B
VOL_200603130934
1 R3T32684U2B 2 R3T32685U2B 3 R3T32686U2B 4 R3T32687U2B
1 / 1
Files includedin the disc are displayed.
No. Appearance State
1 File Loading... Sending files into the memory
2Firmware Updating... XX% Complete.
Writing new version data
--- Firmware Update Failure Failed in updating
Fig. d Programming Mode Screen
* Firmware Version differs depending on the models, and this indication is one example.
Firm Update Mode ver. R3T32684U2B
File Loading...(*1)
Fig. e VFD in Programming Mode (Example)
1-8-1 E7B71TR
TROUBLESHOOTINGNOTE: BOARD MEANS PRINTED CIRCUIT BOARD.
FLOW CHART NO.1The power cannot be turned on.
Is the fuse normal?
Is normal state restored when once unplugged power cord is plugged again after several seconds.
Is the al+5V line voltage normal?
Check each rectifying circuit of secondary circuit and service it if defective.
See FLOW CHART No.2 <The fuse blows out.>
Check for lead or short-circuiting of primarycircuit component and service it if defective.(Q1001,Q1002,Q1003,T1001,D1001,D1002,D1003,D1004,D1011,C1009,C1010)
Yes
Yes
Yes
No
No
No
FLOW CHART NO.2The fuse blows out.
After servicing, replace the fuse.
Check the presence that the primary componentis leaking or shorted and service it if defective.
Check the presence that the rectifying diode or circuit is shorted in each rectifying circuit of secondary side and service it if defective.
FLOW CHART NO.3When the output voltage fluctuates.
No
Yes
Does the secondary side photo coupler circuitoperate normally?
Check the circuit and service it if defective.(IC1001, D1008, D1009, D1010, D1014)
Check the circuit and service it if defective.(IC1001, Q1101, D1111, D1113)
FLOW CHART NO.4When buzz sound can be heard in the vicinity of power circuit.
Check if there is short circuit on the rectifying diode and the circuit in each rectifying circuit of secondary side and service it if defective. (D1101,D1102,D1103,D1104,D1105,D1107,D1108,IC1151,IC1152,Q1154,Q1155,Q1156,Q1158,Q1159,Q1160,Q1163)
No
Yes
FLOW CHART NO.5-FL is not outputted.
Is the supply voltage of -30V fed to the anode of D1104?
Check D1104 and their periphery, and service it if defective.
Check for load circuit short-circuiting or leak, and service it if defective.
1-8-2 E7B71TR
FLOW CHART NO.6P-ON+10V is not outputted.
Is 12V voltage supplied to the emitter of Q1155?
FLOW CHART NO.7AL+9V is not outputted.
Is the "L" pulse outputted to the collector of Q1157?
Check Q1155 and their periphery, and service it if defective.
No
No
NoYes
Yes
Yes
Is the "H" pulse outputted to Pin(53) of IC1501?
Check D1102, D1113, C1117, L1102 and their periphery, and service it if defective.
Is 11V voltage supplied to the collector of Q1156?
Check Q1156, D1156 and their periphery, and service it if defective.
No
Yes
Check D1102, D1113, D1170, D1171, C1117, L1102 and their periphery, and service it if defective.
Is 12V voltage supplied to the collector of Q1160?Yes Check Q1160, D1162 and their periphery, and
service it if defective.
FLOW CHART NO.10EV+32V is not outputted.
Is the supply voltage 44V fed the cathode of D1103?No
YesCheck D1701 and their periphery and service it if defective.
Check D1103, C1113 and their periphery, and service it if defective.
FLOW CHART NO.11AUDIO +5V is not outputted. (P-ON+10V is outputted normally.)
Is 6V voltage supplied to the base of Q1163?No
YesReplace Q1163.
Check D1163, C1168 and their periphery, and service it if defective.
Replace IC1501.
NoReplace Q1157.
FLOW CHART NO.8P-ON+5V(1) is not outputted.
Is 5V voltage supplied to the collector of Q1154?
Check Q1154 and their periphery, and service it if defective.
No
Yes
Check D1108, L1101, C1114 , C1116 and their periphery, and service it if defective.
FLOW CHART NO.9P-ON+5V(2) is not outputted.
Is 5V voltage supplied to the collector of Q1158?
Check Q1158 and their periphery, and service it if defective.
No
Yes
Check D1108, L1105, C1120 and their periphery, and service it if defective.
1-8-3 E7B71TR
Yes
Yes
Yes
Yes
No
No
No
No
FLOW CHART NO.15The fluorescent display tube does not light up.
Is 3.3V voltage supplied to Pin(6, 24) of IC1503?
Is approximately -24V to -28V voltage supplied to Pin(15) of IC1503?
Is there approximately 500kHz oscillation to Pin(26) of IC1503?
Are the filament voltage applied between (1)and (24) of the fluorescent display tube?Also negative voltage applied between these pins and GND?
Replace the fluorescent display tube.
Check the EV+3.3V line and service it if defective.
Check the -FL line and service it if defective.
Check R1560, IC1503 and their periphery, and service it if defective.
Check the power circuit, D1101, D1112, C1106 and their periphery, and service it if defective.
No
YesCheck D1108, L1101, C1114, C1116 and their periphery, and service it if defective.
FLOW CHART NO.14P-ON+3.3V is not outputted.
Is 5V voltage supplied to Pin(1) of IC1152?
Replace IC1152.
NoIs 4V voltage supplied to Pin(1) of IC1151?
FLOW CHART NO.13 P-ON+2.5V is not outputted.
Replace IC1151.
Check D1105, C1110 and their periphery, and service it if defective.Yes
EV+3.3V is not outputted. FLOW CHART NO.12
Is 5V voltage supplied to the collector of Q1159?No
YesIs the voltage of approximately 4V supplied to the base of Q1159?
Check D1108, L1105, C1120 and their periphery, and service it if defective.
NoCheck IC1153 and their periphery, and service it if defective.
Replace Q1159.Yes
1-8-4 E7B71TR
Yes
Yes
No
No
FLOW CHART NO.16The key operation is not functioning.
Are the contact point and the installation state of the key switches normal?
Is the control voltage normally inputted into Pin(1, 2) of IC1501?
Re-install some key switches correctly orreplace some key switches.
Check the key switches and their periphery, and service it if defective.
Replace IC1501 or DVD MECHANISM & DVD MAIN BOARD ASSEMBLY.
Yes
FLOW CHART NO.18The disc tray cannot be opened and closed. (It can be done using the remote control unit.)
Is the normal control voltage inputted to Pin(1) of IC1501? Refer to "FLOW CHART NO.16" <The key operation is not functioning.>
Refer to "FLOW CHART NO.19" <The disc tray cannot be opened and closed.>
Replace the "OPEN/CLOSE" button (SW3006).No
FLOW CHART NO.17
Replace the RM1501 (remote control receiver).Or replace remote control unit.
Check the line between the RM1501 (remote control receiver) and the Pin(27) of IC1501, and service it if defective.
Replace IC1501 or DVD MECHANISM & DVD MAIN BOARD ASSEMBLY.
Is the "L" pulse sent out from Pin(1) terminal of the RM1501 (remote control receiver) when the remote control unit is activated?
Is the "L" pulse signal supplied to the Pin(27) ofIC1501?
Yes
Is 5V voltage supplied to the Pin(3) terminal ofthe RM1501 (remote control receiver)?
Yes
Yes
No
Check AL+5V (1) line and service it if defective.No
No
No operation is possible from the remote control unit. (Operation is possible from the unit.)
0.1460.161
0.4690.4841.1001.1151.7301.7462.4642.4793.300
REC
RECSPEED
REW
PLAY
POWER
FWD
STOP
CH UP
CHDOWNOPEN/CLOSE
----------
KEYTerminal voltage of IC1501-1,2 -1IC1501-1
KEY-2IC1501-2
(V)
1-8-5 E7B71TR
FLOW CHART NO.19The disc tray cannot be opened and closed.
Both functions of picture and sound do not operate normally.
Are the video signals outputted to each pin of CN1201?
Is 5V voltage supplied to the Pin(27,29,47,63) of IC1201?
Replace IC1201. Check AL+5V(2) line and service it if defective.
Yes No
Yes
No
FLOW CHART NO.20
VIDEO E-E does not appear normally.
Are the video signals inputted to each pin of IC1201?
Check the line between video input terminal andeach pin of IC1201.
Are the video signals outputted to each pin of IC1201?
Yes
No
No
IC1201 VIDEO-IN 1 (AV1)16PINIC1201 VIDEO-IN (FRONT)14PINIC1201 Y-IN 1 (FRONT)7PIN
IC1201 VIDEO-Y/CVBS-IN61PINIC1201 VIDEO-C-IN59PIN
CN1201 VIDEO-Y/CVBS-IN10PINCN1201 VIDEO-C-IN8PIN
VIDEO-Y/CVBS-IN10PINVIDEO-C-IN8PIN
IC1201 C-IN 1 (FRONT)9PINIC1201 VIDEO-IN 2 (AV2/REAR)12PINIC1201 Y-IN 2 (REAR)100PINIC1201 C-IN 2 (REAR)1PINIC1201 TUNER-VIDEO
VIDEO-IN 1 (AV1)
Y-IN 1 (FRONT)C-IN 1 (FRONT)VIDEO-IN 2 (AV2)Y-IN 2 (REAR)C-IN 2 (REAR)TUNER-VIDEO20PIN
IC1201 → JK120616PINVIDEO-IN (FRONT)IC1201 → JK120114PIN
IC1201 → JK12127PIN
IC1201 → CN120161PINIC1201 → CN1201 59PIN
Check the line between each pin of IC1201 and each pin of CN1201 and service it if defective.
IC1201 → JK12129PINIC1201 → JK200112PINIC1201 → JK1211100PINIC1201 → JK12111PINIC1201 → TU170120PIN
17PIN
Continued to A on the next page.
Replace the DVD MECHANISM & DVD MAIN BOARD ASSEMBLY.
[No Disc] indicated.
1-8-6 E7B71TR
Is 5V voltage applied to the Pin(27,29,47,63) of IC1201?
Replace IC1201. Check AL+5V(2) line and service it if defective.
Are the video signals outputted to each pin of IC1201?
Yes No
Yes
Yes
No
Check the periphery of JK1205 from Pin (38,39,40) of IC1201 and service it if defective.
Check the periphery of JK1206 from Pin (30) of IC1201 and service it if defective.
Check the periphery of JK2001 from Pin (22) of IC1201 and service it if defective.
Check the periphery of JK1213 from Pin (36) of IC1201 and service it if defective.
Check the periphery of JK1213 from Pin (34) of IC1201 and service it if defective.
Are the video signals outputted to the specific output terminal?
Are the Y, Cb, Cr signals outputted to the COMPONENT OUT terminal (JK1205)?
Are the luminance signals outputted to the S-VIDEO OUT terminal (JK1213)?
Are the chroma signals outputted to the S-VIDEO OUT terminal (JK1213)?
No
No
No
No
No
Are the composite video signals outputted to the VIDEO OUT (AV1) terminal (JK1206)?
Are the composite video signals outputted to the VIDEO OUT (AV2) terminal (JK2001)?
Are the video signals outputted to each pin of CN1201 on the BOARD POWER?
Replace the DVD MECHANISM & DVD MAIN BOARD ASSEMBLY.
Check the line between each pin of CN1201 and each pin of IC1201, and service it if defective.
Are the video signals shown above inputted into each pin of IC1201?
Yes
No
No
CN1201 VIDEO-Y(I/P)-OUT24PINCN1201 VIDEO-Y(I)-OUT30PINCN1201 VIDEO-Cr/Pr-OUT26PINCN1201 VIDEO-Cb/Pb-OUT28PINCN1201 VIDEO-C-OUT
VIDEO-Y(I/P)-OUT
VIDEO-Cr/Pr-OUTVIDEO-Cb/Pb-OUTVIDEO-C-OUT
22PIN
IC1201 VIDEO-Y(I/P)-OUT51PINIC1201 VIDEO-Y(I)-OUT55PINIC1201 VIDEO-Cr/Pr-OUT52PINIC1201 VIDEO-Cb/Pb-OUT53PINIC1201 VIDEO-C-OUT57PIN
IC1201 VIDEO-Y40PINIC1201 VIDEO-Cr/Pr39PINIC1201 VIDEO-Cb/Pb38PINIC1201 Y-OUT36PINIC1201 C-OUT34PINIC1201 VIDEO-OUT 1 (AV1)30PINIC1201 VIDEO-OUT 2 (AV2)22PIN
CN1201 → IC120124PIN
CN1201 → IC120126PINCN1201 → IC120128PIN
→ IC120122PIN
51PINVIDEO-Y(I)-OUTCN1201 → IC120130PIN 55PIN
52PIN53PIN57PINCN1201
A
1-8-7 E7B71TR
FLOW CHART NO.21
Picture does not appear normally.
Set the disc on the disc tray, and playback.
Is 5V voltage applied to the Pin(27,29,47,63) of IC1201?
Replace IC1201. Check AL+5V(2) line and service it if defective.
Are the video signals outputted to each pin of IC1201?
Yes No
Yes
Yes
No
Check the periphery of JK1205 from Pin (38,39,40) of IC1201 and service it if defective.
Check the periphery of JK1206 from Pin (30) of IC1201 and service it if defective.
Check the periphery of JK2001 from Pin (22) of IC1201 and service it if defective.
Check the periphery of JK1213 from Pin (36) of IC1201 and service it if defective.
Check the periphery of JK1213 from Pin (34) of IC1201 and service it if defective.
Are the video signals outputted to the specific output terminal?
Are the Y, Cb, Cr signals outputted to the COMPONENT OUT terminal (JK1205)?
Are the luminance signals outputted to the S-VIDEO OUT terminal (JK1213)?
Are the chroma signals outputted to the S-VIDEO OUT terminal (JK1213)?
No
No
No
No
No
Are the composite video signals outputted to the VIDEO OUT (AV1) terminal (JK1206)?
Are the composite video signals outputted to the VIDEO OUT (AV2) terminal (JK2001)?
Are the video signals outputted to each pin of CN1201 on the BOARD POWER?
Replace the DVD MECHANISM & DVD MAIN BOARD ASSEMBLY.
Check the line between each pin of CN1201 and each pin of IC1201, and service it if defective.
Are the video signals shown above inputted into each pin of IC1201?
Yes
No
No
CN1201 VIDEO-Y(I/P)-OUT24PINCN1201 VIDEO-Y(I)-OUT30PINCN1201 VIDEO-Cr/Pr-OUT26PINCN1201 VIDEO-Cb/Pb-OUT28PINCN1201 VIDEO-C-OUT
VIDEO-Y(I/P)-OUT
VIDEO-Cr/Pr-OUTVIDEO-Cb/Pb-OUTVIDEO-C-OUT
22PIN
IC1201 VIDEO-Y(I/P)-OUT51PINIC1201 VIDEO-Y(I)-OUT55PINIC1201 VIDEO-Cr/Pr-OUT52PINIC1201 VIDEO-Cb/Pb-OUT53PINIC1201 VIDEO-C-OUT57PIN
IC1201 VIDEO-Y40PINIC1201 VIDEO-Cr/Pr39PINIC1201 VIDEO-Cb/Pb38PINIC1201 Y-OUT36PINIC1201 C-OUT34PINIC1201 VIDEO-OUT 1 (AV1)30PINIC1201 VIDEO-OUT 2 (AV2)22PIN
CN1201 → IC120124PIN
CN1201 → IC120126PINCN1201 → IC120128PIN
→ IC120122PIN
51PINVIDEO-Y(I)-OUTCN1201 → IC120130PIN 55PIN
52PIN53PIN57PINCN1201
1-8-8 E7B71TR
Is SIF signal inputted to Pin(2) of IC2?
Are the audio signal outputted to Pin(30,31) of IC1?
Replace TU1701.
Replace IC1.
Yes
Check the line between Pin(30,31) of IC1 and Pin(84,85) of IC1201, and service it if defective.
Yes
No
No
Check the AL+5V(2) , AL+9Vline and service it if defective.
Replace IC1201.
Yes No
FLOW CHART NO.22
Audio E-E does not appear normally.
Are the audio signals inputted to each pin of IC1201?
Check the line between audio input terminal and each pin of IC1201, and service it if defective.
Are the audio signals outputted to Pin(79,80) of IC1201?
Yes
Are the audio signals outputted to Pin(1,7) of IC1203?
Yes
No (Rear or Front input)
No (Tuner)
Replace IC1203.No
No
IC1201 AUDIO-IN1 (AV1)93,94PINIC1201 AUDIO-IN1 (FRONT)91,92PINIC1201 AUDIO-IN2 (AV2)89,90PINIC1201 AUDIO-IN2 (REAR)81,82PINIC1201 TUNER-AUDIO84,85PIN
IC1201 →JK120693,94PINIC1201 →JK1202,
JK120391,92PIN
IC1201 →JK200189,90PINIC1201 →JK120481,82PIN
AUDIO-IN1 (AV1)AUDIO-IN1 (FRONT)
AUDIO-IN2 (AV2)AUDIO-IN2 (REAR)
Is 5V voltage supplied to Pin(63) of IC1201? Is 9V voltage supplied to Pin(75) of IC1201?
Continued to B on the next page.
1-8-9 E7B71TR
Are the analog audio signals outputted to each pin of CN1201 on BOARD POWER?
CN1201 14PIN AUDIO (L)-OUTCN1201 16PIN AUDIO (R)-OUT
IC1202 1PIN AUDIO (L)-OUTIC1202 7PIN AUDIO (R)-OUT
IC1202 2PIN AUDIO (L)-OUTIC1202 6PIN AUDIO (R)-OUT
Replace IC1202.
Check the periphery between Pin(73,74) of IC1201 and the audio terminal (JK1206), and service it if defective.
Check each line between each pin of CN1201 and each pin of IC1202, and service it if defective.
CN1201 14PIN → IC1202 2PIN AUDIO(L)-OUTCN1201 16PIN → IC1202 6PIN AUDIO(R)-OUT
Are the analog audio signals inputted to each pin of IC1202?
Are the analog audio signals outputted to each pin of IC1202?
Are the audio signals outputted to the specific output terminal?
Are the audio signals outputted to the audioterminal (JK1206)?
Are the audio signals outputted to the audioterminal (JK2001)?
Are the audio signals outputted to the audioterminal (JK1210)?
Yes
Yes
Yes
Yes
No
No
IC1201 77PIN AUDIO (L)-OUTIC1201 76PIN AUDIO (R)-OUT
Check each line between each pin of IC1202 and each pin of IC1201, and service it if defective.
IC1202 1PIN → IC1201 77PIN AUDIO(L)-OUTIC1202 7PIN → IC1201 76PIN AUDIO(R)-OUT
Are the analog audio signals inputted to each pin of IC1201?
Yes
No
IC1201 73,74PIN AUDIO-OUT 1 (AV1)IC1201 71,72PIN AUDIO-OUT 2 (AV2)IC1201 67,68PIN AUDIO-OUT 2 (REAR)
Are the analog audio signals outputted to each pin of IC1201?
Yes
No
No
No
No
Check the periphery between Pin(71,72) of IC1201 and the audio terminal (JK2001), and service it if defective.
No
Check the periphery between Pin(67,68) of IC1201 and the audio terminal (JK1210), and service it if defective.
No
Do Pin(12) of CN1201 and Pin(37) of IC1501 become "H" level?
If Pin(12) of CN1201 become "L" level, replace DVD MECHANISM & DVD MAIN BOARD ASSEMBLY.If Pin(37) of IC1501 become "L" level, replace IC1501.
Replace the DVD MECHANISM & DVD MAIN BOARD ASSEMBLY.
B
Check the AL+5V(2) , AL+9Vline and service it if defective.
Replace IC1201.
Yes No
Is 5V voltage supplied to Pin(63) of IC1201?Is 9V voltage supplied to Pin(75) of IC1201?
1-8-10 E7B71TR
Are the analog audio signals outputted to each pin of CN1201 on BOARD POWER?
CN1201 14PIN AUDIO (L)-OUTCN1201 16PIN AUDIO (R)-OUT
IC1202 1PIN AUDIO (L)-OUTIC1202 7PIN AUDIO (R)-OUT
IC1202 2PIN AUDIO (L)-OUTIC1202 6PIN AUDIO (R)-OUT
Replace IC1202.
Check the periphery between Pin(73,74) of IC1201 and the audio terminal (JK1206), and service it if defective.
Check each line between each pin of CN1201 and each pin of IC1202, and service it if defective.
CN1201 14PIN → IC1202 2PIN AUDIO(L)-OUTCN1201 16PIN → IC1202 6PIN AUDIO(R)-OUT
Are the analog audio signals inputted to each pin of IC1202?
Are the analog audio signals outputted to each pin of IC1202?
Are the audio signals outputted to the specific output terminal?
Are the audio signals outputted to the audioterminal (JK1206)?
Are the audio signals outputted to the audioterminal (JK2001)?
Are the audio signals outputted to the audioterminal (JK1210)?
Yes
Yes
Yes
Yes
No
No
IC1201 77PIN AUDIO (L)-OUTIC1201 76PIN AUDIO (R)-OUT
Check each line between each pin of IC1202 and each pin of IC1201, and service it if defective.
IC1202 1PIN → IC1201 77PIN AUDIO(L)-OUTIC1202 7PIN → IC1201 76PIN AUDIO(R)-OUT
Are the analog audio signals inputted to each pin of IC1201?
Yes
No
IC1201 73,74PIN AUDIO-OUT 1 (AV1)IC1201 71,72PIN AUDIO-OUT 2 (AV2)IC1201 67,68PIN AUDIO-OUT 2 (REAR)
Are the analog audio signals outputted to each pin of IC1201?
Yes
No
No
No
No
Check the periphery between Pin(71,72) of IC1201 and the audio terminal (JK2001), and service it if defective.
No
Check the periphery between Pin(67,68) of IC1201 and the audio terminal (JK1210), and service it if defective.
No
Do Pin(12) of CN1201 and Pin(37) of IC1501 become "H" level?
If Pin(12) of CN1201 become "L" level, replace DVD MECHANISM & DVD MAIN BOARD ASSEMBLY.If Pin(37) of IC1501 become "L" level, replace IC1501.
Replace the DVD MECHANISM & DVD MAIN BOARD ASSEMBLY.
Check the AL+5V(2) , AL+9Vline and service it if defective.
Replace IC1201.
Yes No
Is 5V voltage supplied to Pin(63) of IC1201?Is 9V voltage supplied to Pin(75) of IC1201?
FLOW CHART NO.23
Audio is not outputted during playback.
Set the disc on the disc tray, and playback.
1-9-1 E7A70FIS
FUNCTION INDICATOR SYMBOLS
Note: If an error occurs, a message with the error number appears on the screen.
Message Solution Error No. Error Description Priority
Can not record on this disc.Insert the recordable disc, and ensure the disc status satisfies the recording requirements.
1 An error occurs during data reading. -
2 There is no reply for 15 seconds in Test Unit Ready. -
3 Cannot write the data after trying three times. -
4 An error occurs with OPC. -
5 During recovery in a record. -
6 An error occurs even if recovery has been tried three times. -
7 An error occurs in a format. -
8 It cannot start an encode. -
9 NV_PCK/RDI_PCK is not in encoded data. -
10 Encode Pause condition continued for 10 minutes. -
11 Encode Pause condition continued in normal REC condition for 10 minutes. -
12 Difference in the address and can not get StreamID of RDI/VIDEO. -
13 It is a reply that “ATAPI is not readable.” -
14 Cannot write the data after recovering SMALL VMGI. -
15 Cannot write the data after DVD-R Reverse Track. -
16 An error occurs in Finalize Close. -
17 An error occurs in Rec Stop Close. -
18 An error occurs in PCA Full (DVD_R). -
19 Safety Stop occurs during editing. -
20 High Speed Disc. 2
21 The disc is not formatted. 5
22 Disc Error has occurred. 3
23 The -R Disc of VR Mode. 6
24 The disc except DVD-R/RW or finalized DVD-R. 1
This program is not allowed to be recorded.
You cannot record copy prohibited programs.
25 During the Macrovision picture input. 11
26 During the CGMS picture input. 12
This program is not recordable in Video mode.
Set “DVD-RW Recording Format” to “VR mode”. 27 During the CGMS picture (possible to
record once) input. (Video Format Disc) 12
This program is not allowed to be recorded on this disc.
Insert a ver.1.1 CPRM compatible DVD-RW disc. 28
During the CGMS picture (possible to record once) input. (Disc which is not for the correspondence to VR Format CPRM)
12
Recording Error
You cannot record on this disc as Power Calibration Area is full.
E35 Error No.
Error message
1-9-2 E7A70FIS
If an error occurs during the timer recording, one of the following error numbers (40 to 42) or the above error messages (error number: 1 to 39) is displayed on the recording menu after timer recording.(Once the screen of the program line is exited, the program line for the error will be cleared.)(No Error Message is displayed for the error No. 40 ~ 42.)
This disc is protected and not recordable.
Release the disc protect setting in the Disc Setting menu.
29 Disc Protected Disc. 7
Disc is full. (No area for new recording)
Insert the recordable disc with enough recording space. 30 No avilable recording space. 5
You cannot record more than 99 titles on one disc.(The maximum is 99.)
Delete unnecessary titles.31 Its recording capacity has been reached.
(Video Format Disc) 7
32 Its recording capacity has been reached. (VR Format Disc) 8
You cannot record more than 999 chapters on one disc.(The maximum is 999.)
Delete unnecessary chapter markers. 33 The 999 chapter has been reached. (VR
Format Disc) 9
You cannot record on this disc as Control Information is full. Delete unnecessary titles. 34 There is not space to record field of
control information. 10
You cannot record on the disc as Power Calibration Area is full.
Insert a new disc. 35 PCA is Full. (in REC start) 4
This disc is already finalized. Release the finalizing for this disc. 36 It is finalized. (Video Format Disc) 6
Can not record on this disc. Repeat the same operation.
37 Access to Memory Area range outside. -
38 Sector Address is wrong. -
39 BUP writing error of chapter editing. -
Message Solution Error No. Error Description Priority
Error message is not displayed.
- Set the timer programming correctly.
- Set the timer programming before the start time.
40
- Some portion has not been recorded because of program overlapping.
- Recording did not start at the start time.-
Turn the power on and set the clock correctly then set timer programming again.
41 Power failed -
Insert the recordable disc. 42 No disc when recording -
Message Solution Error No. Error Description Priority
2. ---
3. ---
4. ---
5. ---
6. ---
7. ---
8. ---
A program with the error number is grayed out and asterisked on the timer programming list.
The speed mode changes to the error number.
Timer Programming
1-17-1 E7B71CEX
EXPLODED VIEWS
Cabinet
NOTE: BOARD MEANS PRINTED CIRCUIT BOARD.
See Electrical Parts Listfor parts with this mark.
Some Ref. Numbers are not in sequence.
2L021
2L021
2L021
2L011
2L011
2L021
2L0312L031
2L031
2B15
A6
2L021
2L012
2L013
2L021
2L081
2L081
2L081
2L081
2L081
2B1
2B112B9
2B5
2B2
A5
A5A4
A1X
2B3
2B4
2B13
2B12
A2
BOARD JUNCTION
BOARD AFV
BOARD JACK
BOARD PSV
2L019
FM1001
BOARD POWER
BOARD SWITCH
BOARD POWER SUPPLY
POWER ASSEMBLY ( P1 )
( P3 )
( P4 )
( P2 )DVD MECHANISM & DVD MAIN BOARD ASSEMBLY
NOTES1. BOARD POWER and
BOARD SWITCH are supplied as an Assembly.
2. BOARD POWER SUPPLY, BOARD JACK and BOARD JUNCTION are supplied as an Assembly.
( Refer to the Electrical Parts List )
1-17-2 E7B71PEX
Packing
Some Ref. Numbers are not in sequence.
Unit
X10X8X7 X4 X1
20060313 1-18-1 E7B71CA
MECHANICAL PARTS LIST
PRODUCT SAFETY NOTE: Products marked with a ! have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
!Loca-
tion No. TSB P/N Reference No. Description
A1X P000459750 1VM222036 PANEL FRONT E7B71BD
A2 P000459740 1VM120917 COVER TOP(R3 PAL) E7B70ED
A4 1VM120045A CHASSIS E6700ED
A5 0VM403657A FOOT K7010UA
A6 1VM220260 FAN COVER E6800ED
2B1 1VM220926A BOARD HOLDER E7A00UD
2B2 1VM422494 COVER CABLE E7A00UD
2B4 XP0U039WD001 LOCKING CARD SPACER KGLS-22S
2B5 1VM420990 POWER PLATE EARTH E6800ED
2B9 1VM322117 POWER HOLDER E7B20ED
2B13 1VM320610 PLATE GROUND(RCA) E6800ED
2B15 1VM320812 FAN EARTH E6800ED
FM1001 P000459880 MMEZL12NH008 MOTOR DC FAN D05U-12TS1 09(UX)
2L011 GBJP3060 SCREW P-TIGHT M3X6 BIND HEAD+
2L012 GBHB3080 SCREW B-TIGHT M3X8 BIND HEAD+
2L013 GBHP3080 SCREW P-TIGHT M3X8 BIND HEAD+ BLK
2L021 GBCS3060 SCREW S-TIGHT M3X6 BIND CROM
2L031 GBJS3100 SCREW S-TIGHT M3X10 BIND HEAD+
2L081 GBJS3060 SCREW S-TIGHT M3X6 BIND HEAD+
ACCESSORIESX1 P000459890 NB311BD REMOTE CONTROL UNIT
NB311BD
X4 P000460030 WPZ0122LG001 RF CORD PAL 1.2M
X7 P000459770 1VMN22905 QUICK GUIDE E7B71BD
X8 1VMN22863 REGISTE RATION CARD E7B71BD
X10 P000459760 1VMN22575 OWNERS MANUAL E7B71BD
20060313 1-19-1 E7B71EL
ELECTRICAL PARTS LIST
PRODUCT SAFETY NOTE: Products marked with a ! have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
NOTES:
1. Parts that are not assigned part numbers (---------) are not available.
2. Tolerance of Capacitors and Resistors are noted with the following symbols.
DVD MECHANISM & DVD MAIN BOARD ASSEMBLY
POWER ASSEMBLY
BOARD POWER
C.....±0.25% D.....±0.5% F.....±1%
G.....±2% J......±5% K.....±10%
M.....±20% N.....±30% Z.....+80/-20%
!Location
No. TSB P/N Reference No. Description
! P2 P000460160 N78E3CBN DVD MECHANISM & DVD MAIN BOARD ASSEMBLY
!Location
No. TSB P/N Reference No. Description
! P1 P000459800 1VSA14365 POWER ASSEMBLYConsists of the following:
---------- BOARD POWER (SUB-A)
---------- BOARD SWITCH (SUB-B)
!Location
No. TSB P/N Reference No. Description
---------- BOARD POWER (SUB-A)Consists of the following:
CAPACITORSC1151 CE1CMASDL100 ELECTROLYTIC CAP. 10µF/
16V M
C1152 CE1CMASDL470 ELECTROLYTIC CAP. 47µF/16V M
C1153 CE1CMASDL101 ELECTROLYTIC CAP. 100µF/16V M
C1154 CE1CMASDL221 ELECTROLYTIC CAP. 220µF/16V M
C1155 CCA1JZTFZ104 CERAMIC CAP.(AX) F Z 0.1µF/50V
C1160 CE1CMASDL470 ELECTROLYTIC CAP. 47µF/16V M
C1163 CHD1JK30B103 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V
C1164 CE1CMASDL101 ELECTROLYTIC CAP. 100µF/16V M
C1167 CE0KMASDL101 ELECTROLYTIC CAP. 100µF/6.3V M
C1168 CE1CMASDL470 ELECTROLYTIC CAP. 47µF/16V M
C1173 CE0KMASDL101 ELECTROLYTIC CAP. 100µF/6.3V M
C1174 CE0KMASDL101 ELECTROLYTIC CAP. 100µF/6.3V M
C1175 CE0KMASDL471 ELECTROLYTIC CAP. 470µF/6.3V M
C1176 CHD1JZ30F104 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V
C1177 CHD1JZ30F104 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V
C1202 CHD1JK30B102 CHIP CERAMIC CAP.(1608) B K 1000pF/50V
C1203 CHD1JZ30F104 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V
C1206 CHD1JZ30F104 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V
C1207 CHD1JZ30F104 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V
C1208 CE1CMASDL221 ELECTROLYTIC CAP. 220µF/16V M
C1209 CHD1JZ30F104 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V
C1210 CE1CMASDL100 ELECTROLYTIC CAP. 10µF/16V M
C1211 CE1CMASDL100 ELECTROLYTIC CAP. 10µF/16V M
C1212 CHD1JJ3CH330 CHIP CERAMIC CAP.(1608) CH J 33pF/50V
C1213 CHD1JJ3CH330 CHIP CERAMIC CAP.(1608) CH J 33pF/50V
C1215 CHD1JZ30F104 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V
C1216 CE0KMASDL101 ELECTROLYTIC CAP. 100µF/6.3V M
C1218 CE0KMASDL471 ELECTROLYTIC CAP. 470µF/6.3V M
C1221 CE1CMASDL100 ELECTROLYTIC CAP. 10µF/16V M
C1222 CE1CMASDL100 ELECTROLYTIC CAP. 10µF/16V M
C1223 CHD1JJ3CH271 CHIP CERAMIC CAP.(1608) CH J 270pF/50V
C1224 CHD1JJ3CH271 CHIP CERAMIC CAP.(1608) CH J 270pF/50V
C1225 CHD1JJ3CH470 CHIP CERAMIC CAP.(1608) CH J 47pF/50V
C1226 CHD1JJ3CH470 CHIP CERAMIC CAP.(1608) CH J 47pF/50V
C1227 CHD1JZ30F104 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V
C1228 CE1CMASDL100 ELECTROLYTIC CAP. 10µF/16V M
C1229 CE1CMASDL100 ELECTROLYTIC CAP. 10µF/16V M
C1230 CE1JMASDLR47 ELECTROLYTIC CAP. 0.47µF/50V M
C1231 CE1JMASDLR47 ELECTROLYTIC CAP. 0.47µF/50V M
C1232 CE1JMASDLR47 ELECTROLYTIC CAP. 0.47µF/50V M
C1233 CE1JMASDLR47 ELECTROLYTIC CAP. 0.47µF/50V M
C1234 CE1JMASDLR47 ELECTROLYTIC CAP. 0.47µF/50V M
C1235 CE1JMASDL1R0 ELECTROLYTIC CAP. 1µF/50V M
C1236 CE1JMASDLR47 ELECTROLYTIC CAP. 0.47µF/50V M
C1237 CHD1JZ30F104 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V
C1238 CE1JMASDLR47 ELECTROLYTIC CAP. 0.47µF/50V M
C1239 CE1EMASDL4R7 ELECTROLYTIC CAP. 4.7µF/25V M
C1240 CE1JMASDLR47 ELECTROLYTIC CAP. 0.47µF/50V M
C1241 CE1JMASDLR47 ELECTROLYTIC CAP. 0.47µF/50V M
C1242 CE1JMASDLR47 ELECTROLYTIC CAP. 0.47µF/50V M
C1243 CE1JMASDL1R0 ELECTROLYTIC CAP. 1µF/50V M
C1244 CE1EMASDL4R7 ELECTROLYTIC CAP. 4.7µF/25V M
!Location
No. TSB P/N Reference No. Description
20060313 1-19-2 E7B71EL
C1245 CHD1JZ30F104 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V
C1246 CE1EMASDL4R7 ELECTROLYTIC CAP. 4.7µF/25V M
C1247 CE1AMASDL470 ELECTROLYTIC CAP. 47µF/10V M
C1248 CE1EMASDL4R7 ELECTROLYTIC CAP. 4.7µF/25V M
C1249 CE1JMASDL1R0 ELECTROLYTIC CAP. 1µF/50V M
C1250 CHD1JZ30F104 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V
C1251 CE1EMASDL4R7 ELECTROLYTIC CAP. 4.7µF/25V M
C1252 CE1EMASDL4R7 ELECTROLYTIC CAP. 4.7µF/25V M
C1253 CE1JMASDL1R0 ELECTROLYTIC CAP. 1µF/50V M
C1254 CE1EMASDL4R7 ELECTROLYTIC CAP. 4.7µF/25V M
C1255 CE1EMASDL4R7 ELECTROLYTIC CAP. 4.7µF/25V M
C1256 CHD1JZ30F104 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V
C1257 CE1EMASDL4R7 ELECTROLYTIC CAP. 4.7µF/25V M
C1258 CE1JMASDL1R0 ELECTROLYTIC CAP. 1µF/50V M
C1259 CE1EMASDL4R7 ELECTROLYTIC CAP. 4.7µF/25V M
C1260 CE1EMASDL4R7 ELECTROLYTIC CAP. 4.7µF/25V M
C1261 CE1JMASDL1R0 ELECTROLYTIC CAP. 1µF/50V M
C1262 CE0KMASDL470 ELECTROLYTIC CAP. 47µF/6.3V M
C1263 CHD1JZ30F104 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V
C1264 JW5.0T BOARD JUMPER D0.6-P5.0
C1265 CE1JMASDL1R0 ELECTROLYTIC CAP. 1µF/50V M
C1266 CHD1JZ30F104 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V
C1267 CE1CMASDL100 ELECTROLYTIC CAP. 10µF/16V M
C1268 CHD1JZ30F104 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V
C1269 CE1JMASDL1R0 ELECTROLYTIC CAP. 1µF/50V M
C1270 CHD1JZ30F104 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V
C1272 CHD1JZ30F104 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V
C1273 CHD1JZ30F104 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V
C1274 CE1JMASDL1R0 ELECTROLYTIC CAP. 1µF/50V M
C1275 CHD1JZ30F104 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V
C1276 CE0KMASDL470 ELECTROLYTIC CAP. 47µF/6.3V M
C1277 CE1JMASDL1R0 ELECTROLYTIC CAP. 1µF/50V M
C1278 CHD1JZ30F104 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V
C1279 CE0KMASDL470 ELECTROLYTIC CAP. 47µF/6.3V M
C1280 CE1JMASDL1R0 ELECTROLYTIC CAP. 1µF/50V M
C1281 CE1JMASDL1R0 ELECTROLYTIC CAP. 1µF/50V M
C1282 CE0KMASDL471 ELECTROLYTIC CAP. 470µF/6.3V M
C1283 CE0KMASDL471 ELECTROLYTIC CAP. 470µF/6.3V M
C1284 CCA1EKT0B104 CERAMIC CAP.(AX) B K 0.1µF/25V
C1285 CE1JMASDL1R0 ELECTROLYTIC CAP. 1µF/50V M
C1286 CE0KMASDL471 ELECTROLYTIC CAP. 470µF/6.3V M
!Location
No. TSB P/N Reference No. Description
C1287 CE1JMASDL1R0 ELECTROLYTIC CAP. 1µF/50V M
C1288 CE0KMASDL471 ELECTROLYTIC CAP. 470µF/6.3V M
C1290 CE1JMASDL1R0 ELECTROLYTIC CAP. 1µF/50V M
C1291 CE0KMASDL471 ELECTROLYTIC CAP. 470µF/6.3V M
C1292 CE0KMASDL471 ELECTROLYTIC CAP. 470µF/6.3V M
C1293 CE0KMASDL471 ELECTROLYTIC CAP. 470µF/6.3V M
C1294 CE0KMASDL471 ELECTROLYTIC CAP. 470µF/6.3V M
C1295 CHD1JZ30F104 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V
C1296 CHD1JZ30F104 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V
C1297 CE0KMASDL470 ELECTROLYTIC CAP. 47µF/6.3V M
C1301 CHD1JK30B222 CHIP CERAMIC CAP. B K 2200pF/50V
C1302 CHD1JK30B222 CHIP CERAMIC CAP. B K 2200pF/50V
C1303 CE1CMASDL101 ELECTROLYTIC CAP. 100µF/16V M
C1501 CHD1JJ3CH220 CHIP CERAMIC CAP.(1608) CH J 22pF/50V
C1502 CHD1JJ3CH180 CHIP CERAMIC CAP. CH J 18pF/50V
C1504 CHD1JZ30F104 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V
If C1507A is 0.015µF, then IC1502A is R3112N191A-TR-FA.
C1507A CHD1JK30B153 CHIP CERAMIC CAP.(1608) B K 0.015µF/50V
IC1502A P000459990 QSZBA0TRC021 VOLTAGE DETECT R3112N191A-TR-FA
If C1507B is 0.1µF, then IC1502B is PST3619NR.
C1507B CHD1JK30B104 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V
IC1502B P000459980 QSZBA0TMM151 SYSTEM RESET IC PST3619NR
C1508 CCA1JZTFZ104 CERAMIC CAP.(AX) F Z 0.1µF/50V
C1509 CE0KMASDL471 ELECTROLYTIC CAP. 470µF/6.3V M
C1510 CCA1JZTFZ104 CERAMIC CAP.(AX) F Z 0.1µF/50V
C1512 CHD1JJ3CH101 CHIP CERAMIC CAP.(1608) CH J 100pF/50V
C1515 CE1JMASDL220 ELECTROLYTIC CAP. 22µF/50V M
C1517 CHD1JZ30F104 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V
C1519 CHD1JZ30F104 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V
C1520 CHD1JZ30F104 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V
C1521 CE1JMASDL3R3 ELECTROLYTIC CAP. 3.3µF/50V M
C1522 CHD1JJ3CH101 CHIP CERAMIC CAP.(1608) CH J 100pF/50V
C1523 CHD1JZ30F104 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V
C1524 CE0KMASDL101 ELECTROLYTIC CAP. 100µF/6.3V M
C1526 CE1CMASDL100 ELECTROLYTIC CAP. 10µF/16V M
C1527 CE0KMASDL470 ELECTROLYTIC CAP. 47µF/6.3V M
C1641 CHD1JJ3CH220 CHIP CERAMIC CAP.(1608) CH J 22pF/50V
C1645 CHD1JJ3CH270 CHIP CERAMIC CAP. CH J 27pF/50V
C1646 CE1EMASDL4R7 ELECTROLYTIC CAP. 4.7µF/25V M
C1647 CDA1EKS0X183 SEMICONDUCTOR CAP. SR K 0.018µF/25V
C1648 CE1JMASDL1R0 ELECTROLYTIC CAP. 1µF/50V M
!Location
No. TSB P/N Reference No. Description
20060313 1-19-3 E7B71EL
C1649 CE1JMASDL1R0 ELECTROLYTIC CAP. 1µF/50V M
C1650 CHD1JK30B103 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V
C1651 CE0KMASDL470 ELECTROLYTIC CAP. 47µF/6.3V M
C1704 CHD1JK30B103 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V
C1708 CHD1JZ30F104 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V
C1709 CHD1JK30B103 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V
C1710 CHD1JK30B102 CHIP CERAMIC CAP.(1608) B K 1000pF/50V
C1711 CHD1JZ30F103 CHIP CERAMIC CAP. F Z 0.01µF/50V
C1713 CHD1JZ30F103 CHIP CERAMIC CAP. F Z 0.01µF/50V
C1714 CE1JMASDL100 ELECTROLYTIC CAP. 10µF/50V M
C1715 CE1JMASDLR33 ELECTROLYTIC CAP. 0.33µF/50V M
C1716 CE1CMASDL100 ELECTROLYTIC CAP. 10µF/16V M
C1801 CHD1JK30B222 CHIP CERAMIC CAP. B K 2200pF/50V
C1803 CHD1JK30B222 CHIP CERAMIC CAP. B K 2200pF/50V
C1806 CHD1JK30B222 CHIP CERAMIC CAP. B K 2200pF/50V
C1807 CHD1JK30B102 CHIP CERAMIC CAP.(1608) B K 1000pF/50V
C1808 CHD1JK30B222 CHIP CERAMIC CAP. B K 2200pF/50V
C1809 CHD1JK30B222 CHIP CERAMIC CAP. B K 2200pF/50V
C1811 CE1JMASDL1R0 ELECTROLYTIC CAP. 1µF/50V M
C1812 CHD1JK30B222 CHIP CERAMIC CAP. B K 2200pF/50V
C1813 CHD1JZ30F104 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V
C1814 CHD1JK30B102 CHIP CERAMIC CAP.(1608) B K 1000pF/50V
C1816 CHD1JZ30F104 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V
C1817 CE1JMASDL1R0 ELECTROLYTIC CAP. 1µF/50V M
C1819 CHD1JK30B222 CHIP CERAMIC CAP. B K 2200pF/50V
C1820 CHD1JK30B222 CHIP CERAMIC CAP. B K 2200pF/50V
C1821 CHD1JK30B222 CHIP CERAMIC CAP. B K 2200pF/50V
C1823 CHD1JK30B222 CHIP CERAMIC CAP. B K 2200pF/50V
C1825 CE0KMASDL470 ELECTROLYTIC CAP. 47µF/6.3V M
C1827 CHD1JK30B102 CHIP CERAMIC CAP.(1608) B K 1000pF/50V
C1831 CE1JMASDL1R0 ELECTROLYTIC CAP. 1µF/50V M
C1834 CE0KMASDL470 ELECTROLYTIC CAP. 47µF/6.3V M
CONNECTORSCN1152 J322C15TG001 242 SERIES CONNECTOR
224202115W1
CN1601 J3PHC02JG017 PH CONNECTOR (WHITE) TOP 2P B2B-PH-K-S(LF)
CN1701 E6851AFV AFV BOARD ASSEMBLY E6851BD
DIODESD1151 NDLZ001N5397 DIODE 1N5397-B
D1154 NDLZ001N5397 DIODE 1N5397-B
D1156 NDTB00DZ10BS ZENER DIODE DZ-10BSBT265
D1157 JW5.0T BOARD JUMPER D0.6-P5.0
D1158 NDTZ01N4148M SWITCHING DIODE 1N4148M
D1159 NDTZ01N4148M SWITCHING DIODE 1N4148M
D1160 NDTZ01N4148M SWITCHING DIODE 1N4148M
!Location
No. TSB P/N Reference No. Description
D1162 NDTB00DZ11BS ZENER DIODE DZ-11BSBT265
D1163 NDTB0DZ5R6BS ZENER DIODE DZ-5.6BSBT265
D1165 NDTZ01N4148M SWITCHING DIODE 1N4148M
D1166 NDTZ01N4148M SWITCHING DIODE 1N4148M
D1167 NDTZ01N4148M SWITCHING DIODE 1N4148M
D1170 NDQZ001N4005 RECTIFIER DIODE 1N4005
D1171 NDQZ001N4005 RECTIFIER DIODE 1N4005
D1172 NDQZ001N4005 RECTIFIER DIODE 1N4005
D1173 NDQZ001N4005 RECTIFIER DIODE 1N4005
D1174 NDTZ01N4148M SWITCHING DIODE 1N4148M
D1175 NDTZ01N4148M SWITCHING DIODE 1N4148M
D1501 NDTZ01N4148M SWITCHING DIODE 1N4148M
D1502 NDTA0DZ7R5BS ZENER DIODE DZ-7.5BSAT265
D1507 NDTC0DZ4R3BS ZENER DIODE DZ-4.3BSCT265
D1508 NDTC0DZ5R6BS ZENER DIODE DZ-5.6BSCT265
D1509 NDTZ01N4148M SWITCHING DIODE 1N4148M
D1601 NDTZ01N4148M SWITCHING DIODE 1N4148M
D1701 NDTB00DZ33BS ZENER DIODE DZ-33BSBT265
D1801 NDTA00DZ11BS ZENER DIODE DZ-11BSAT265
D1802 NDTA00DZ11BS ZENER DIODE DZ-11BSAT265
D1803 NDTA00DZ11BS ZENER DIODE DZ-11BSAT265
D1804 NDTA00DZ11BS ZENER DIODE DZ-11BSAT265
D1805 NDTA00DZ11BS ZENER DIODE DZ-11BSAT265
D1806 NDTA00DZ11BS ZENER DIODE DZ-11BSAT265
D1807 NDTA00DZ11BS ZENER DIODE DZ-11BSAT265
D1808 NDTA00DZ11BS ZENER DIODE DZ-11BSAT265
D1809 NDTA00DZ11BS ZENER DIODE DZ-11BSAT265
D1810 NDTA00DZ11BS ZENER DIODE DZ-11BSAT265
D1811 NDTC0DZ4R3BS ZENER DIODE DZ-4.3BSCT265
ICSIC1151 P000457260 QSZBA0SSH054 VOLTAGE REGULATOR
PQ070XF01SZH
IC1152 P000457260 QSZBA0SSH054 VOLTAGE REGULATOR PQ070XF01SZH
IC1153 P000459940 NSZBA0TJY036 IC SHUNT REGULATOR KIA431-AT/P
IC1201 P000459970 QSZBA0RHT051 IC INTERFACE HA118326APF-E
IC1202 P000459910 NSZBA0SJY035 IC OP AMP KIA4558P/P
IC1203 P000457180 NSZBA0STY173 IC OP AMP RC4580IP
IC1501 P000459960 QSZAA0RMS051 MICROCONTROLLER 8BIT MN101C77A FM
If IC1502A is R3112N191A-TR-FA, then C1507A is 0.015µF.
IC1502A P000459990 QSZBA0TRC021 VOLTAGE DETECT R3112N191A-TR-FA
C1507A CHD1JK30B153 CHIP CERAMIC CAP.(1608) B K 0.015µF/50V
If IC1502B is PST3619NR, then C1507B is 0.1µF.
IC1502B P000459980 QSZBA0TMM151 SYSTEM RESET IC PST3619NR
C1507B CHD1JK30B104 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V
IC1503 P000459930 NSZBA0T0S005 VFD DRIVER IC SC16313G
IC1641 P000460000 QSZBA0TSY018 IC VPS/PDC SLICER LC74793JM-TLM-E
COILSL1201 LLAXKATTU101 INDUCTOR(100µH K)
LAP02TA101K
L1203 LLBD00PKV022 CHOKE COIL 47µH
L1205 LLAXKATTU101 INDUCTOR(100µH K) LAP02TA101K
L1206 LLAXKATTU101 INDUCTOR(100µH K) LAP02TA101K
L1207 JW5.0T BOARD JUMPER D0.6-P5.0
L1209 LLAXKATTU101 INDUCTOR(100µH K) LAP02TA101K
L1501 LLAXKATTU101 INDUCTOR(100µH K) LAP02TA101K
!Location
No. TSB P/N Reference No. Description
20060313 1-19-4 E7B71EL
L1502 LLAXKATTU101 INDUCTOR(100µH K) LAP02TA101K
L1703 LLAXKATTU100 INDUCTOR 10µH-K-26T
L1801 LLAXKATTU101 INDUCTOR(100µH K) LAP02TA101K
L1802 LLAXKATTUR47 INDUCTOR(0.47µH K) LAP02TAR47K
L1803 1VSA11351 BEAD CORE ASSEMBLY E6820ED
TRANSISTORSQ1154 NQS4KTC3266P TRANSISTOR KTC3266-GR-
AT/P
Q1155 NQSYKTA1273P TRANSISTOR KTA1273-Y-AT/P
Q1156 QQSK2SC2001A TRANSISTOR 2SC2001-T-A-K
Q1157 NQSYKTC3199P TRANSISTOR KTC3199-Y-AT/P
Q1158 NQSYKTC3203P TRANSISTOR KTC3203-Y-AT/P
Q1159 NQSYKTC3199P TRANSISTOR KTC3199-Y-AT/P
Q1160 NQSYKTC3199P TRANSISTOR KTC3199-Y-AT/P
Q1163 NQSYKTC3199P TRANSISTOR KTC3199-Y-AT/P
Q1164 NQSZKRC103MP NPN TRANSISTOR KRC103M-AT/P
Q1201 NQSYKTC3199P TRANSISTOR KTC3199-Y-AT/P
Q1202 NQSYKTC3199P TRANSISTOR KTC3199-Y-AT/P
Q1203 NQSZKRC103MP NPN TRANSISTOR KRC103M-AT/P
Q1204 NQS4KTA1266P TRANSISTOR KTA-1266-GR-AT/P
Q1205 NQSZKRC103MP NPN TRANSISTOR KRC103M-AT/P
Q1207 NQSYKTC3199P TRANSISTOR KTC3199-Y-AT/P
Q1501 NQS5KTC3199P TRANSISTOR KTC3199-BL-AT/P
Q1502 NQSZKRC103MP NPN TRANSISTOR KRC103M-AT/P
Q1503 NQSZKRC103MP NPN TRANSISTOR KRC103M-AT/P
Q1504 NQSYKTA1267P TRANSISTOR KTA1267-Y-AT/P
Q1505 NQSYKTC3199P TRANSISTOR KTC3199-Y-AT/P
Q1506 QF1GSSM3K15F MOS FET SSM3K15F(TE85L F)
Q1507 QF1GSSM3K15F MOS FET SSM3K15F(TE85L F)
Q1508 NQSYKTC3203P TRANSISTOR KTC3203-Y-AT/P
Q1602 NQSYKTC3199P TRANSISTOR KTC3199-Y-AT/P
Q1801 NQSYKTA1267P TRANSISTOR KTA1267-Y-AT/P
Q1802 NQS4KTA1266P TRANSISTOR KTA-1266-GR-AT/P
Q1803 NQSYKTC3199P TRANSISTOR KTC3199-Y-AT/P
Q1804 NQSYKTC3199P TRANSISTOR KTC3199-Y-AT/P
Q1805 NQSYKTC3199P TRANSISTOR KTC3199-Y-AT/P
Q1806 NQSYKTC3199P TRANSISTOR KTC3199-Y-AT/P
Q1807 NQSYKTC3199P TRANSISTOR KTC3199-Y-AT/P
Q1810 NQSYKTC3199P TRANSISTOR KTC3199-Y-AT/P
Q1811 NQSYKTC3199P TRANSISTOR KTC3199-Y-AT/P
Q1812 NQSYKTC3199P TRANSISTOR KTC3199-Y-AT/P
Q1813 NQSYKTC3199P TRANSISTOR KTC3199-Y-AT/P
Q1814 NQSYKTC3199P TRANSISTOR KTC3199-Y-AT/P
RESISTORSR1151 RRXAZR5Z0000 CHIP RES.(1608) 1/10W 0 ΩR1152 RCX4JATZ0102 CARBON RES. 1/4W J 1k ΩR1155 RCX4JATZ0102 CARBON RES. 1/4W J 1k ΩR1156 RCX4JATZ05R6 CARBON RES. 1/4W J 5.6 ΩR1157 RCX4JATZ08R2 CARBON RES. 1/4W J 8.2 ΩR1158 RCX4JATZ0391 CARBON RES. 1/4W J 390 ΩR1159 RRXAJR5Z0473 CHIP RES. 1/10W J 47k ΩR1160 JW5.0T BOARD JUMPER D0.6-P5.0
R1162 RCX4JATZ0561 CARBON RES. 1/4W J 560 ΩR1163 RCX4JATZ0561 CARBON RES. 1/4W J 560 ΩR1164 RCX4JATZ0561 CARBON RES. 1/4W J 560 ΩR1165 RCX4JATZ0561 CARBON RES. 1/4W J 560 ΩR1167 RCX4JATZ0152 CARBON RES. 1/4W J 1.5k ΩR1170 RRXAJR5Z0472 CHIP RES. 1/10W J 4.7k ΩR1171 RCX4JATZ0681 CARBON RES. 1/4W J 680 Ω
!Location
No. TSB P/N Reference No. Description
R1172 RCX4JATZ0681 CARBON RES. 1/4W J 680 ΩR1173 RRXAJR5Z0471 CHIP RES. 1/10W J 470 ΩR1174 RCX4JATZ0391 CARBON RES. 1/4W J 390 ΩR1175 RRXAJR5Z0151 CHIP RES. 1/10W J 150 ΩR1176 RRXAJR5Z0331 CHIP RES. 1/10W J 330 ΩR1177 RRXAJR5Z0151 CHIP RES. 1/10W J 150 ΩR1178 RRXAFR5H4701 CHIP RES. 1/10W F 4.7k ΩR1179 RRXAFR5H1501 CHIP RES. 1/10W F 1.5k ΩR1180 RRXAFR5H1000 CHIP RES. 1/10W F 100 ΩR1182 JW5.0T BOARD JUMPER D0.6-P5.0
R1183 RRXAJR5Z0471 CHIP RES. 1/10W J 470 ΩR1184 RRXAJR5Z0471 CHIP RES. 1/10W J 470 ΩR1186 RRXAFR5H1002 CHIP RES. 1/10W F 10k ΩR1187 RRXAFR5H1002 CHIP RES. 1/10W F 10k ΩR1188 RRXAFR5H1502 CHIP RES. 1/10W F 15k ΩR1189 RRXAFR5H1002 CHIP RES. 1/10W F 10k ΩR1190 RRXAFR5H2701 CHIP RES. 1/10W F 2.7k ΩR1191 RRXAFR5H1200 CHIP RES. 1/10W F 120 ΩR1192 RRXAFR5H1501 CHIP RES. 1/10W F 1.5k ΩR1193 RRXAJR5Z0222 CHIP RES. 1/10W J 2.2k ΩR1194 RRXAJR5Z0222 CHIP RES. 1/10W J 2.2k ΩR1195 RRXAJR5Z0102 CHIP RES. 1/10W J 1k ΩR1199 RRXAJR5Z0473 CHIP RES. 1/10W J 47k ΩR1200 RRXAJR5Z0472 CHIP RES. 1/10W J 4.7k ΩR1201 RRXAFR5H2400 CHIP RES. 1/10W F 240 ΩR1202 RRXAFR5H2000 CHIP RES. 1/10W F 200 ΩR1203 RRXAFR5H2000 CHIP RES. 1/10W F 200 ΩR1204 RRXAFR5H2000 CHIP RES. 1/10W F 200 ΩR1205 RRXAFR5H2200 CHIP RES. 1/10W F 220 ΩR1207 RRXAJR5Z0102 CHIP RES. 1/10W J 1k ΩR1208 RRXAJR5Z0332 CHIP RES. 1/10W J 3.3k ΩR1209 RRXAJR5Z0302 CHIP RES. 1/10W J 3k ΩR1210 RRXAJR5Z0302 CHIP RES. 1/10W J 3k ΩR1214 RRXAJR5Z0471 CHIP RES. 1/10W J 470 ΩR1215 RRXAJR5Z0471 CHIP RES. 1/10W J 470 ΩR1216 RCX4JATZ0102 CARBON RES. 1/4W J 1k ΩR1217 RCX4JATZ0331 CARBON RES. 1/4W J 330 ΩR1219 RRXAJR5Z0123 CHIP RES. 1/10W J 12k ΩR1220 RRXAJR5Z0123 CHIP RES. 1/10W J 12k ΩR1221 RRXAFR5H3302 CHIP RES. 1/10W F 33.0k ΩR1222 RRXAFR5H3302 CHIP RES. 1/10W F 33.0k ΩR1224 RCX6JATZ0682 CARBON RES. 1/6W J 6.8k ΩR1225 RRXAJR5Z0682 CHIP RES. 1/10W J 6.8k ΩR1226 RRXAJR5Z0683 CHIP RES. 1/10W J 68k ΩR1227 RRXAJR5Z0683 CHIP RES. 1/10W J 68k ΩR1228 RRXAFR5H8201 CHIP RES. 1/10W F 8.2k ΩR1229 RRXAFR5H8201 CHIP RES. 1/10W F 8.2k ΩR1230 RRXAFR5H1302 CHIP RES. 1/10W F 13k ΩR1231 RRXAJR5Z0133 CHIP RES. 1/10W J 13k ΩR1232 RRXAFR5H1302 CHIP RES. 1/10W F 13k ΩR1233 RRXAJR5Z0133 CHIP RES. 1/10W J 13k ΩR1234 RRXAJR5Z0104 CHIP RES. 1/10W J 100k ΩR1235 RRXAJR5Z0104 CHIP RES. 1/10W J 100k ΩR1236 RRXAJR5Z0471 CHIP RES. 1/10W J 470 ΩR1237 RRXAJR5Z0471 CHIP RES. 1/10W J 470 ΩR1238 RRXAJR5Z0103 CHIP RES. 1/10W J 10k ΩR1239 RCX4JATZ0750 CARBON RES. 1/4W J 75 ΩR1244 RRXAJR5Z0105 CHIP RES. 1/10W J 1M ΩR1245 RRXAJR5Z0105 CHIP RES. 1/10W J 1M ΩR1246 RRXAJR5Z0105 CHIP RES. 1/10W J 1M ΩR1247 RRXAJR5Z0105 CHIP RES. 1/10W J 1M ΩR1248 RRXAJR5Z0183 CHIP RES. 1/10W J 18k ΩR1249 RRXAJR5Z0183 CHIP RES. 1/10W J 18k ΩR1250 RCX6JATZ0151 CARBON RES. 1/6W J 150 ΩR1251 RRXAFR5H3301 CHIP RES. 1/10W F 3.3k ΩR1253 RCX4JATZ0681 CARBON RES. 1/4W J 680 Ω
!Location
No. TSB P/N Reference No. Description
20060313 1-19-5 E7B71EL
R1254 RRXAJR5Z0221 CHIP RES. 1/10W J 220 ΩR1501 RCX4JATZ0821 CARBON RES. 1/4W J 820 ΩR1502 RRXAJR5Z0101 CHIP RES. 1/10W J 100 ΩR1504 RRXAJR5Z0103 CHIP RES. 1/10W J 10k ΩR1505 RRXAJR5Z0103 CHIP RES. 1/10W J 10k ΩR1506 RRXAJR5Z0103 CHIP RES. 1/10W J 10k ΩR1508 RRXAJR5Z0103 CHIP RES. 1/10W J 10k ΩR1510 RRXAJR5Z0473 CHIP RES. 1/10W J 47k ΩR1511 RRXAJR5Z0393 CHIP RES. 1/10W J 39k ΩR1513 RRXAZR5Z0000 CHIP RES.(1608) 1/10W 0 ΩR1515 RRXAJR5Z0332 CHIP RES. 1/10W J 3.3k ΩR1516 RRXAJR5Z0471 CHIP RES. 1/10W J 470 ΩR1517 RRXAJR5Z0332 CHIP RES. 1/10W J 3.3k ΩR1518 RRXAJR5Z0823 CHIP RES. 1/10W J 82k ΩR1519 RRXAJR5Z0473 CHIP RES. 1/10W J 47k ΩR1520 RRXAJR5Z0101 CHIP RES. 1/10W J 100 ΩR1521 RRXAJR5Z0101 CHIP RES. 1/10W J 100 ΩR1522 RRXAJR5Z0101 CHIP RES. 1/10W J 100 ΩR1525 RRXAJR5Z0101 CHIP RES. 1/10W J 100 ΩR1527 RRXAJR5Z0103 CHIP RES. 1/10W J 10k ΩR1528 RRXAJR5Z0223 CHIP RES. 1/10W J 22k ΩR1531 RRXAJR5Z0101 CHIP RES. 1/10W J 100 ΩR1532 RRXAJR5Z0103 CHIP RES. 1/10W J 10k ΩR1533 RRXAJR5Z0223 CHIP RES. 1/10W J 22k ΩR1534 RCX6JATZ0101 CARBON RES. 1/6W J 100 ΩR1535 RRXAJR5Z0473 CHIP RES. 1/10W J 47k ΩR1536 RRXAJR5Z0101 CHIP RES. 1/10W J 100 ΩR1537 RRXAJR5Z0101 CHIP RES. 1/10W J 100 ΩR1540 RRXAJR5Z0101 CHIP RES. 1/10W J 100 ΩR1542 RRXAJR5Z0473 CHIP RES. 1/10W J 47k ΩR1543 RRXAZR5Z0000 CHIP RES.(1608) 1/10W 0 ΩR1544 RRXAZR5Z0000 CHIP RES.(1608) 1/10W 0 ΩR1545 RRXAJR5Z0473 CHIP RES. 1/10W J 47k ΩR1546 RRXAJR5Z0473 CHIP RES. 1/10W J 47k ΩR1548 RRXAJR5Z0472 CHIP RES. 1/10W J 4.7k ΩR1549 RRXAJR5Z0473 CHIP RES. 1/10W J 47k ΩR1551 RRXAJR5Z0472 CHIP RES. 1/10W J 4.7k ΩR1553 RRXAJR5Z0471 CHIP RES. 1/10W J 470 ΩR1554 RRXAJR5Z0103 CHIP RES. 1/10W J 10k ΩR1555 RRXAJR5Z0103 CHIP RES. 1/10W J 10k ΩR1556 RRXAJR5Z0102 CHIP RES. 1/10W J 1k ΩR1557 RRXAJR5Z0102 CHIP RES. 1/10W J 1k ΩR1559 RRXAJR5Z0102 CHIP RES. 1/10W J 1k ΩR1560 RRXAJR5Z0683 CHIP RES. 1/10W J 68k ΩR1561 RRXAZR5Z0000 CHIP RES.(1608) 1/10W 0 ΩR1563 RRXAJR5Z0682 CHIP RES. 1/10W J 6.8k ΩR1564 JW5.0T BOARD JUMPER D0.6-P5.0
R1565 JW5.0T BOARD JUMPER D0.6-P5.0
R1566 RCX4JATZ0561 CARBON RES. 1/4W J 560 ΩR1567 RRXAJR5Z0473 CHIP RES. 1/10W J 47k ΩR1568 RRXAJR5Z0473 CHIP RES. 1/10W J 47k ΩR1569 RRXAJR5Z0473 CHIP RES. 1/10W J 47k ΩR1570 RRXAJR5Z0473 CHIP RES. 1/10W J 47k ΩR1571 RRXAJR5Z0473 CHIP RES. 1/10W J 47k ΩR1572 JW5.0T BOARD JUMPER D0.6-P5.0
R1604 RCX4JATZ0820 CARBON RES. 1/4W J 82 ΩR1605 RRXAJR5Z0102 CHIP RES. 1/10W J 1k ΩR1606 RRXAJR5Z0102 CHIP RES. 1/10W J 1k ΩR1645 RRXAJR5Z0272 CHIP RES. 1/10W J 2.7k ΩR1646 RRXAZR5Z0000 CHIP RES.(1608) 1/10W 0 ΩR1647 RRXAZR5Z0000 CHIP RES.(1608) 1/10W 0 ΩR1648 RRXAJR5Z0103 CHIP RES. 1/10W J 10k ΩR1649 RRXAJR5Z0103 CHIP RES. 1/10W J 10k ΩR1650 RRXAJR5Z0562 CHIP RES. 1/10W J 5.6k ΩR1651 RRXAJR5Z0103 CHIP RES. 1/10W J 10k ΩR1652 RRXAJR5Z0101 CHIP RES. 1/10W J 100 Ω
!Location
No. TSB P/N Reference No. Description
R1706 RCX6JATZ0332 CARBON RES. 1/6W J 3.3k ΩR1707 RCX6JATZ0222 CARBON RES. 1/6W J 2.2k ΩR1708 RRXAZR5Z0000 CHIP RES.(1608) 1/10W 0 ΩR1709 RRXAZR5Z0000 CHIP RES.(1608) 1/10W 0 ΩR1710 RRXAJR5Z0331 CHIP RES. 1/10W J 330 ΩR1711 RRXAJR5Z0331 CHIP RES. 1/10W J 330 ΩR1712 RRXAJR5Z0331 CHIP RES. 1/10W J 330 ΩR1713 RRXAJR5Z0331 CHIP RES. 1/10W J 330 ΩR1714 RRXAZR5Z0000 CHIP RES.(1608) 1/10W 0 ΩR1801 RRXAJR5Z0750 CHIP RES. 1/10W J 75 ΩR1802 RRXAJR5Z0750 CHIP RES. 1/10W J 75 ΩR1803 RRXAJR5Z0750 CHIP RES. 1/10W J 75 ΩR1804 RRXAJR5Z0102 CHIP RES. 1/10W J 1k ΩR1806 RRXAJR5Z0102 CHIP RES. 1/10W J 1k ΩR1808 RRXAJR5Z0223 CHIP RES. 1/10W J 22k ΩR1809 RRXAJR5Z0223 CHIP RES. 1/10W J 22k ΩR1810 RRXAZR5Z0000 CHIP RES.(1608) 1/10W 0 ΩR1812 RRXAJR5Z0103 CHIP RES. 1/10W J 10k ΩR1813 RCX6JATZ0303 CARBON RES. 1/6W J 30k ΩR1814 RRXAJR5Z0182 CHIP RES. 1/10W J 1.8k ΩR1815 RRXAJR5Z0222 CHIP RES. 1/10W J 2.2k ΩR1816 RCX4JATZ0750 CARBON RES. 1/4W J 75 ΩR1817 RCX6JATZ0911 CARBON RES. 1/6W J 910 ΩR1818 RRXAJR5Z0222 CHIP RES. 1/10W J 2.2k ΩR1819 RRXAJR5Z0750 CHIP RES. 1/10W J 75 ΩR1820 RCX4JATZ0471 CARBON RES. 1/4W J 470 ΩR1821 RCX4JATZ0471 CARBON RES. 1/4W J 470 ΩR1822 RRXAJR5Z0221 CHIP RES. 1/10W J 220 ΩR1824 RRXAJR5Z0750 CHIP RES. 1/10W J 75 ΩR1825 RRXAJR5Z0102 CHIP RES. 1/10W J 1k ΩR1826 RRXAJR5Z0102 CHIP RES. 1/10W J 1k ΩR1827 RCX6JATZ0911 CARBON RES. 1/6W J 910 ΩR1829 RCX4JATZ0750 CARBON RES. 1/4W J 75 ΩR1830 RCX4JATZ0750 CARBON RES. 1/4W J 75 ΩR1831 RCX4JATZ0750 CARBON RES. 1/4W J 75 ΩR1833 RCX4JATZ0750 CARBON RES. 1/4W J 75 ΩR1834 RCX4JATZ0750 CARBON RES. 1/4W J 75 ΩR1835 RRXAJR5Z0750 CHIP RES. 1/10W J 75 ΩR1836 RRXAJR5Z0750 CHIP RES. 1/10W J 75 ΩR1837 RRXAJR5Z0750 CHIP RES. 1/10W J 75 ΩR1840 RRXAJR5Z0221 CHIP RES. 1/10W J 220 ΩR1841 RRXAJR5Z0221 CHIP RES. 1/10W J 220 ΩR1842 RRXAJR5Z0104 CHIP RES. 1/10W J 100k ΩR1844 RRXAJR5Z0750 CHIP RES. 1/10W J 75 ΩR1845 RCX6JATZ0101 CARBON RES. 1/6W J 100 ΩR1848 RRXAJR5Z0102 CHIP RES. 1/10W J 1k ΩR1849 RRXAJR5Z0102 CHIP RES. 1/10W J 1k ΩR1850 RRXAJR5Z0221 CHIP RES. 1/10W J 220 ΩR1851 RRXAJR5Z0221 CHIP RES. 1/10W J 220 ΩR1853 RRXAJR5Z0750 CHIP RES. 1/10W J 75 ΩR1854 RRXAJR5Z0472 CHIP RES. 1/10W J 4.7k ΩR1855 RRXAJR5Z0472 CHIP RES. 1/10W J 4.7k ΩR1856 RRXAJR5Z0472 CHIP RES. 1/10W J 4.7k ΩR1857 RRXAJR5Z0472 CHIP RES. 1/10W J 4.7k ΩR1858 RRXAJR5Z0103 CHIP RES. 1/10W J 10k ΩR1859 RRXAJR5Z0471 CHIP RES. 1/10W J 470 ΩR1860 RRXAJR5Z0473 CHIP RES. 1/10W J 47k ΩR1861 RRXAJR5Z0472 CHIP RES. 1/10W J 4.7k Ω
MISCELLANEOUS2B3 1VM320515 FL HOLDER E6700UD
FL1501 P000457330 TVFD1C0FT048 VACUUM FLUORESCENT DISPLAY 7-BT-301N
JK1201 P000457110 JXRL010LY135 JACK RCA(YELLOW) MTJ-032-05B-20(B110)
JK1202 P000457120 JXRL010LY136 JACK RCA(WHITE) MTJ-032-05B-22(B110)
JK1203 P000457090 JYRL010LY029 JACK RCA(RED) MTJ-032-05A-21(B110)
!Location
No. TSB P/N Reference No. Description
20060313 1-19-6 E7B71EL
BOARD SWITCH
BOARD PSV
BOARD POWER SUPPLY
JK1204 P000459860 JXRL020LY123 PIN JACK 2P MSD-242V-01 NI FE LF
JK1205 P000457140 JXRL030LY132 JACK RCA 3PIN MSD-243V-18 NI FE LF
JK1206 P000459850 JXGL210LY008 RGB CONNECTOR MRC-021V-05 ABS(B110
JK1209 P000457100 JXRL010LY125 JACK RCA(BLACK) MSP-251V-01 NI FE LF
JK1210 P000459860 JXRL020LY123 PIN JACK 2P MSD-242V-01 NI FE LF
JK1211 P000457070 JXEL040LY003 JACK S TYPE MDC-050V-2.4 LF(B110
JK1212 P000457080 JXEL040RP003 MINI DIN SOCKET MDC1-34-020
JK1213 P000457070 JXEL040LY003 JACK S TYPE MDC-050V-2.4 LF(B110
JW001 P000460040 WX1E6820-002 FFC CABLE 30P FFC/P1.00/70
JW002 P000460040 WX1E6820-002 FFC CABLE 30P FFC/P1.00/70
JW010 P000460060 WX1E6820-006 FLAT CABLE 3P AWG26#2651/P2.0/100
JW011 P000460090 WX1E7B20-003 1PIN WIRE AWG26/UL1007 TR-64/7
RM1501 P000457340 USESJRSKK039 REMOTE RECEIVER PIC-37043LU
TU1701 P000460020 UTUNPLGAL017 TUNER UNIT TMFE2-301A
X1501 P000459810 FXC323LQUA02 XTAL QTF38-32768K125P20L
X1502 P000459830 FY0805PMR002 CERAMIC RESONETOR CSTLS8M00G56-B0
X1641 P000459820 FXC445LDS003 Xtal 1K*044335DA
!Location
No. TSB P/N Reference No. Description
---------- BOARD SWITCH (SUB-B)Consists of the following:
RESISTORSR3003 RRXAJR5Z0301 CHIP RES. 1/10W J 300 ΩR3004 RRXAJR5Z0621 CHIP RES. 1/10W J 620 ΩR3005 RRXAJR5Z0102 CHIP RES. 1/10W J 1k ΩR3006 RRXAJR5Z0222 CHIP RES. 1/10W J 2.2k ΩR3007 RRXAJR5Z0682 CHIP RES. 1/10W J 6.8k ΩR3010 RRXAJR5Z0301 CHIP RES. 1/10W J 300 ΩR3012 RRXAJR5Z0222 CHIP RES. 1/10W J 2.2k ΩR3015 RRXAJR5Z0621 CHIP RES. 1/10W J 620 ΩR3016 RRXAJR5Z0102 CHIP RES. 1/10W J 1k ΩR3017 RRXAJR5Z0682 CHIP RES. 1/10W J 6.8k Ω
SWITCHESSW3001 P000460010 SST0101HH003 TACT SWITCH KSM0612B
SW3002 P000460010 SST0101HH003 TACT SWITCH KSM0612B
SW3003 P000460010 SST0101HH003 TACT SWITCH KSM0612B
SW3004 P000460010 SST0101HH003 TACT SWITCH KSM0612B
SW3005 P000460010 SST0101HH003 TACT SWITCH KSM0612B
SW3006 P000460010 SST0101HH003 TACT SWITCH KSM0612B
SW3007 P000460010 SST0101HH003 TACT SWITCH KSM0612B
SW3008 P000460010 SST0101HH003 TACT SWITCH KSM0612B
SW3009 P000460010 SST0101HH003 TACT SWITCH KSM0612B
SW3011 P000460010 SST0101HH003 TACT SWITCH KSM0612B
!Location
No. TSB P/N Reference No. Description
! P3 P000459790 1VSA14349 BOARD PSVConsists of the following:
---------- BOARD POWER SUPPLY (PSV-A)
---------- BOARD JUNCTION (PSV-B)
---------- BOARD JACK (PSV-C)
!Location
No. TSB P/N Reference No. Description
!Location
No. TSB P/N Reference No. Description
---------- BOARD POWER SUPPLY (PSV-A) Consists of the following:
CAPACITORS! C1001 CT2E683DC011 METALIZED FILM CAP. 0.068µF/
250V K
! C1002 CE1CMASDL100 ELECTROLYTIC CAP. 10µF/16V M
C1003 CCD1JZSYV223 CERAMIC CAP. YV Z 0.022µF/50V
! C1004 CCN2EMA0E222 SAFTY CAP. 2200pF/250V
C1005 CA2H101S6016 ELECTROLYTIC CAP. 100µF/400V M
C1006 CCA1CKT0X182 CERAMIC CAP.(AX) X K 1800pF/16V
C1008 CCA1JKT0B102 CERAMIC CAP.(AX) B K 1000pF/50V
C1009 CCD3AKPSL560 CERAMIC CAP. SL K 56pF/1KV
C1010 CCD2JKP0B103 CERAMIC CAP. B K 0.01µF/500V
C1101 CCD2JKP0B471 CERAMIC CAP. B K 470pF/500V
C1104 CHD1JK30B333 CHIP CERAMIC CAP.(1608) B K 0.033µF/50V
C1106 CE1CMASDL101 ELECTROLYTIC CAP. 100µF/16V M
C1107 CE1JMASDL220 ELECTROLYTIC CAP. 22µF/50V M
C1108 CHD1JK30B103 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V
C1109 CHD1JZ30F104 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V
C1110 CE0KMASDL102 ELECTROLYTIC CAP. 1000µF/6.3V M
C1111 CE0KMZADL332 ELECTROLYTIC CAP. 3300µF/6.3V SL
C1112 CE1CMASDL102 ELECTROLYTIC CAP. 1000µF/16V M
C1113 CE1JMASDL100 ELECTROLYTIC CAP. 10µF/50V M
C1114 CE0KMZADL472 ELECTROLYTIC CAP. 4700µF/6.3V SL
C1115 CHD1JK30B103 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V
C1116 CE0KMASDL102 ELECTROLYTIC CAP. 1000µF/6.3V M
C1117 CE1CMASDL471 ELECTROLYTIC CAP. 470µF/16V M
C1120 CE0KMASDL102 ELECTROLYTIC CAP. 1000µF/6.3V M
DIODESD1001 NDLZ001N5397 DIODE 1N5397-B
D1002 NDLZ001N5397 DIODE 1N5397-B
D1003 NDLZ001N5397 DIODE 1N5397-B
D1004 NDLZ001N5397 DIODE 1N5397-B
D1005 NDTZ01N4148M SWITCHING DIODE 1N4148M
D1006 NDTZ01N4148M SWITCHING DIODE 1N4148M
D1007 NDTZ01N4148M SWITCHING DIODE 1N4148M
D1008 NDTZ01N4148M SWITCHING DIODE 1N4148M
D1009 NDTZ01N4148M SWITCHING DIODE 1N4148M
D1010 NDTZ01N4148M SWITCHING DIODE 1N4148M
D1011 NDQZ000BA159 RECTIFIER DIODE BA159
D1013 JW5.0T BOARD JUMPER D0.6-P5.0
D1101 NDQZ000BA157 RECTIFIER DIODE BA157
D1102 NDQZ000SB380 SCHOTTKY BARRIER DIODE SB380
D1103 NDQZ000BA157 RECTIFIER DIODE BA157
D1104 NDQZ000BA157 RECTIFIER DIODE BA157
D1105 NDQZ000SB140 SCHOTTKY BARRIER DIODE SB140
D1107 NDQZ000SB240 SCHOTTKY BARRIER DIODE SB240-B/P
D1108 NDQZ000SB340 SCHOTTKY BARRIER DIODE SB340
D1111 NDTB0DZ6R8BS ZENER DIODE DZ-6.8BSBT265
D1112 NDTA00DZ20BS ZENER DIODE DZ-20BSAT265
D1113 NDTB00DZ15BS ZENER DIODE DZ-15BSBT265
20060313 1-19-7 E7B71EL
BOARD JUNCTION
BOARD JACK
IC! IC1001 P000459900 NPEA000EL817 PHOTOCOUPLER EL817A
COILSL1001 1VSA11355 BEAD CORE ASSEMBLY
E6820ED
L1002 1VSA11355 BEAD CORE ASSEMBLY E6820ED
L1003 1VSA11355 BEAD CORE ASSEMBLY E6820ED
! L1004 LLBG00ZTU022 LINE FILTER 56MH TLF14CB5630R2
L1005 XL03010XM001 BEAD CORE B16 RH 3.5X10X1.3
L1101 LLC150KKV007 POWER INDUCTORS TWKBNP-150K
L1102 LLC180KKV007 POWER INDUCTORS TWKBNP-180K
L1105 LLBD00PKV022 CHOKE COIL 47µH
TRANSISTORSQ1001 NQSYKTC3199P TRANSISTOR KTC3199-Y-AT/P
Q1002 QQS12SC1815F TRANSISTOR 2SC1815-GR(TE2 F T)
! Q1003 QFWZ02SK3566 FET 2SK3566
Q1101 NQSYKTA1267P TRANSISTOR KTA1267-Y-AT/P
RESISTORS! R1001 RCX2565FS001 CARBON RES. 1/2W K 5.6M Ω
R1002 RCX4JATZ0564 CARBON RES. 1/4W J 560k ΩR1003 RCX4JATZ0564 CARBON RES. 1/4W J 560k ΩR1004 RCX6JATZ0104 CARBON RES. 1/6W J 100k ΩR1005 RCX6JATZ0103 CARBON RES. 1/6W J 10k ΩR1006 RCX6JATZ0474 CARBON RES. 1/6W J 470k ΩR1007 RCX6JATZ0104 CARBON RES. 1/6W J 100k ΩR1009 RCX4JATZ0105 CARBON RES. 1/4W J 1M ΩR1010 RCX4JATZ0105 CARBON RES. 1/4W J 1M ΩR1011 RCX4JATZ0105 CARBON RES. 1/4W J 1M ΩR1012 RCX6JATZ0152 CARBON RES. 1/6W J 1.5k ΩR1013 RCX4GATZ0821 CARBON RES. 1/4W G 820 ΩR1014 RCX6JATZ0104 CARBON RES. 1/6W J 100k ΩR1016 RN01JZLZ02R7 METAL OXIDE FILM RES. 1W J
2.7 ΩR1017 RCX6JATZ0562 CARBON RES. 1/6W J 5.6k ΩR1018 RCX4JATZ0102 CARBON RES. 1/4W J 1k ΩR1019 RN02823ZU001 METAL OXIDE FILM RES. 2W J
82k ΩR1020 RN011R8ZU001 METAL OXIDE FILM RES. 1W J
1.8 ΩR1101 RRXAJR5Z0102 CHIP RES. 1/10W J 1k ΩR1102 RRXAZR5Z0000 CHIP RES.(1608) 1/10W 0 ΩR1103 RRXAJR5Z0472 CHIP RES. 1/10W J 4.7k ΩR1104 RRXAJR5Z0182 CHIP RES. 1/10W J 1.8k ΩR1105 RRXAZR5Z0000 CHIP RES.(1608) 1/10W 0 ΩR1106 RRXAFR5H0222 CHIP RES.(1608) 1/10W F 2.2k
ΩR1108 RRXAFR5H0562 CHIP RES. 1/10W F 5.6k ΩR1109 RCX4JATZ0102 CARBON RES. 1/4W J 1k Ω
MISCELLANEOUS2B11 1VM420987 HEAT SINK E6800ED
2L019 GBJS3080 SCREW S-TIGHT M3X8 BIND HEAD+
! AC1001 WAB0182LW016 POWER CORD PE8G2X91H0AA061
! F1001 P000459950 PAGC20BW3162 FUSE T1.6AL/250V
FH1001 XH01Z00LY002 FUSE HOLDER MSF-015 LF (B110)
FH1002 XH01Z00LY002 FUSE HOLDER MSF-015 LF (B110)
SA1001 P000457210 NVQZ10D471KB SURGE ABSORBER 470V+-10PER
! T1001 P000459870 LTTZPE0XB003 TRANS POWER BCK-28-9980
!Location
No. TSB P/N Reference No. Description
!Location
No. TSB P/N Reference No. Description
---------- BOARD JUNCTION (PSV-B) Consists of the following:
CONNECTORCN1106 JCTUB15TG002 242 SERIES CONNECTOR
TUC-P15X-B1 WHT ST
MISCELLANEOUSJW1001 P000460050 WX1E6820-005 FLAT CABLE 8P AWG26#2651/
P2.0/70
JW1002 P000460070 WX1E6820-007 FLAT CABLE 7P AWG26#2651/P2.0/70
!Location
No. TSB P/N Reference No. Description
---------- BOARD JACK (PSV-C) Consists of the following:
CAPACITORSC2002 CCA1CKT0X222 CERAMIC CAP.(AX) X K 2200pF/
16V
C2004 CCA1CKT0X222 CERAMIC CAP.(AX) X K 2200pF/16V
C2005 CHD1JJ3CH471 CHIP CERAMIC CAP.(1608) CH J 470pF/50V
C2006 CHD1JK30B222 CHIP CERAMIC CAP. B K 2200pF/50V
C2007 CHD1JJ3CH471 CHIP CERAMIC CAP.(1608) CH J 470pF/50V
C2008 CCA1JKT0B102 CERAMIC CAP.(AX) B K 1000pF/50V
C2009 CE1JMASDL1R0 ELECTROLYTIC CAP. 1µF/50V M
C2010 CE1JMASDL1R0 ELECTROLYTIC CAP. 1µF/50V M
C2011 CHD1JK30B102 CHIP CERAMIC CAP.(1608) B K 1000pF/50V
C2021 CE0KMASDL471 ELECTROLYTIC CAP. 470µF/6.3V M
C2022 CE1CMASDL101 ELECTROLYTIC CAP. 100µF/16V M
DIODESD2001 NDTA00DZ11BS ZENER DIODE DZ-11BSAT265
D2002 NDTA00DZ11BS ZENER DIODE DZ-11BSAT265
D2003 NDTA00DZ11BS ZENER DIODE DZ-11BSAT265
D2004 NDTA00DZ11BS ZENER DIODE DZ-11BSAT265
D2005 NDTA00DZ11BS ZENER DIODE DZ-11BSAT265
D2006 NDTA00DZ11BS ZENER DIODE DZ-11BSAT265
D2007 NDTA00DZ11BS ZENER DIODE DZ-11BSAT265
D2008 NDTA00DZ11BS ZENER DIODE DZ-11BSAT265
D2009 NDTA00DZ11BS ZENER DIODE DZ-11BSAT265
D2010 NDTA00DZ11BS ZENER DIODE DZ-11BSAT265
COILL2003 1VSA11351 BEAD CORE ASSEMBLY
E6820ED
TRANSISTORSQ2001 NQSYKTC3199P TRANSISTOR KTC3199-Y-AT/P
Q2002 NQSYKTC3199P TRANSISTOR KTC3199-Y-AT/P
Q2003 NQS4KTA1266P TRANSISTOR KTA-1266-GR-AT/P
RESISTORSR2001 RRXAJR5Z0221 CHIP RES. 1/10W J 220 ΩR2002 RCX4JATZ0750 CARBON RES. 1/4W J 75 ΩR2003 RRXAJR5Z0750 CHIP RES. 1/10W J 75 ΩR2004 RCX4JATZ0681 CARBON RES. 1/4W J 680 ΩR2005 RCX4JATZ0821 CARBON RES. 1/4W J 820 ΩR2006 RCX6JATZ0472 CARBON RES. 1/6W J 4.7k ΩR2007 RCX4JATZ0821 CARBON RES. 1/4W J 820 ΩR2008 RCX6JATZ0472 CARBON RES. 1/6W J 4.7k ΩR2009 RRXAJR5Z0750 CHIP RES. 1/10W J 75 ΩR2010 RRXAJR5Z0750 CHIP RES. 1/10W J 75 ΩR2011 RRXAJR5Z0750 CHIP RES. 1/10W J 75 Ω
20060313 1-19-8 E7B71EL
BOARD AFV
R2012 RRXAJR5Z0102 CHIP RES. 1/10W J 1k ΩR2013 RRXAJR5Z0102 CHIP RES. 1/10W J 1k ΩR2014 RRXAJR5Z0750 CHIP RES. 1/10W J 75 Ω
MISCELLANEOUS2B12 1VM423185 21P PLATE EARTH E7B20ED
JK2001 P000459840 JXGL210LY006 RGB CONNECTOR MRC-021V-03 ABS(B11
JW2001 P000460080 WX1E7B20-002 FLAT CABLE 15P AWG26#2651/P2.0/70
!Location
No. TSB P/N Reference No. Description
P4 P000459780 1VSA12358 BOARD AFVConsists of the following:
CAPACITORSC1 CHD1JZ30F104 CHIP CERAMIC CAP.(1608) F Z
0.1µF/50V
C4 CHD1JJ3CH560 CHIP CERAMIC CAP. CH J 56pF/50V
C5 CHD1JJ3CH220 CHIP CERAMIC CAP.(1608) CH J 22pF/50V
C6 CHD1JJ3CH560 CHIP CERAMIC CAP. CH J 56pF/50V
C7 CHD1JC3CH3R0 CHIP CERAMIC CAP. CH C 3pF/50V
C8 CHD1JC3CH3R0 CHIP CERAMIC CAP. CH C 3pF/50V
C11 CHD1JK30B103 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V
C12 CE1CMASSL100 ELECTROLYTIC CAP. 10µF/16V M H7
C13 CHD1JK30B103 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V
C14 CHD1JK30B103 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V
C15 CE1CMASSL100 ELECTROLYTIC CAP. 10µF/16V M H7
C16 CE1CMASSL100 ELECTROLYTIC CAP. 10µF/16V M H7
C17 CHD1JZ30F104 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V
C19 CHD1JZ30F104 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V
C20 CE1JMASSL3R3 ELECTROLYTIC CAP. 3.3µF/50V M H7
C21 CHD1JZ30F104 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V
C22 CE1CMASSL100 ELECTROLYTIC CAP. 10µF/16V M H7
C24 CE1JMASSLR22 ELECTROLYTIC CAP. 0.22µF/50V M H7
C27 CCA1JZTFZ104 CERAMIC CAP.(AX) F Z 0.1µF/50V
CONNECTORCN1 JTED009ER045 ANGLE PIN HEADER 9P IMSA-
6029B-1-09Z003-
DIODED2 NDTZ01N4148M SWITCHING DIODE 1N4148M
ICIC1 P000459920 NSZBA0SP3005 IC AUDIO PROCESSOR
MSP3417G-QG-B8-V3
COILSL1 LLAXKATTU100 INDUCTOR 10µH-K-26T
L2 JW5.0T BOARD JUMPER D0.6-P5.0
L3 LLAXKATTU180 INDUCTOR 18µH-K-26T
L4 LLAXKATTU100 INDUCTOR 10µH-K-26T
RESISTORSR1 RRXAJR5Z0102 CHIP RES. 1/10W J 1k ΩR4 RRXAJR5Z0124 CHIP RES. 1/10W J 120k ΩR5 RRXAZR5Z0000 CHIP RES.(1608) 1/10W 0 ΩR6 RRXAZR5Z0000 CHIP RES.(1608) 1/10W 0 Ω
MISCELLANEOUSX1 FXD186LLN001 XTAL 18.432MHz
!Location
No. TSB P/N Reference No. Description
SERVICE MANUAL
TOSHIBA CORPORATION 2006
The above model is classified as a green product (*1), as indicated by the underlined serialnumber. This Service Manual describes replacement parts for the green product. Whenrepairing this green product, use the part(s) described in this manual and lead-free solder (*2).
For (*1) and (*2), see the next page.
FILE NO. 810-200617GR
DVD Video Recorder
D-R160SB
Published in Japan, Mar. 2006 GREEN
®
1-10-1
BLOCK DIAGRAMSSystem Control Block Diagram
E7B71BLS
IC101(MAIN MICRO CONTROLLER)
IC1501(SUB MICRO CONTROLLER)
REMOTESENSOR
RM1501
1G
7G
~
23
17
~
a
hi
~
7
14
~
GRID
RESET EV+3.3V
VFD
SEGMENT
FL1501IC1503
IC1502
BOARD POWER
DVD MAIN BOARD
(VFD DRIVER)
KEY SWITCH
KEY SWITCH
CN1502CN3001
KEY-1 11KEY-2 22
BOARD SWITCH
16
2812
485049
27
12
52
53
38393334
2219182029
N23J25T4
N24L25R24
89
12
14
30
7
1 2
11
27MHzX'TAL
X802
CLK 27 IN
CLK 27 OUT
SYS-RESETSYS-RESET
SUB-RXDSUB-TXD
SUB-SCLKRDY
CN701SYS-RESETSUB-RXDSUB-TXDSUB-SCLKRDY
CN1201
REG-CONT
PWSW
AUDIO-MUTEDVD-AUDIO-MUTE
DAVN-LDAVN-L
DVD-AUDIO-MUTE
SCART-AUDIO-MUTESCART-AUDIO-MUTE
SUB-SDASUB-SCL
OSC2OSC1
X OUTX IN
RESET
P-DOWN
BUP+3.3V
FL-DINFL-CLKFL-STB
REMOTE
KEY-1KEY-2
REG-CONT
PWSW
SDASCL
AUDIO-MUTE37
24
TO POWER SUPPLYBLOCK DIAGRAM
TO AUDIO BLOCK DIAGRAM
8MHzRESONATOR
X1502
32.768KHzX'TAL
X1501
Q1504
Q1505C1509
(BACKUP CAPACITOR)
DINCLKSTB
2 FAN-GND1 FAN+12V
CN1601FAN
N1
SCL
SDA
TU1701(TUNER UNIT)
9
10
EV+5V
Q1602
Q1506Q1507
FAN-AL+12V55FAN-CONT2
N2
4 4SYS-RESET1 1SUB-RXD3 3SUB-TXD5 5SUB-SCLK2 2RDY
IC106
CN101 CN115126
P-ON+1.2V
30 301V2CONT
+1.2VREGULATOR
SDASCL TO VIDEO
BLOCK DIAGRAM
1V2CONT
VI+1.2V
NOTE: BOARD MEANS PRINTED CIRCUIT BOARD.
1-10-2
Digital Signal Process Block Diagram
E7B71BLD
IC101
FRONT-ENDDIGITALSIGNALPROCESS
IC201
RF/ERROR AMP
IC301
MOTORDRIVER
MOTORDRIVER
IC202
OP AMP
IC302
IC104 (FLASH MEMORY)
DVD MAIN BOARD
TO VIDEOBLOCKDIAGRAM
TO AUDIOBLOCKDIAGRAM
T2
M4
G4
L4
K1
G3
U1R3U2
M25K26P24T3
P2R1P3
R2R26
D/A
D/A
D/A
D/A
AUDIOI/F
VIDEOENCODER
BACK-ENDDIGITALSIGNALPROCESS
VIDEOI/F
FLASH MEMORY
FEENCODER
TRAY OPEN
IC102,IC103 (DDR SDRAM)
DDR SDRAM
CN201
DVD MECHANISM
TILT
TRACKING
FOCUS
PICK-UP
SLEDMOTOR
M
REC VIDEO SIGNAL PB VIDEO SIGNAL REC AUDIO SIGNAL PB AUDIO SIGNAL
D/A
BOARDENCODER
LPC
CN1001
CN701
CN1003
SPINDLEMOTOR
MCN1002
BOARDRELAY
CN301
+3.3V
IC701 (VIDEO DECODER)
DECODER A/D45-50Y2, AA4, AB1-AB4
DECODER A/D39-44V3, Y3, W1,Y4, W2, AA3
1013
VIDEO-Y(I/P)-OUT 24VIDEO-Y(I)-OUT 30VIDEO-C-OUT 22
VIDEO-C-IN 8
VIDEO-Cb/Pb-OUT 28VIDEO-Cr/Pr-OUT 26VIDEO-Y/CVBS-IN 10
IC801(AUDIO D/A CONVERTER)
AUDIO D/ACONVERTER
768
151416
43
5
IC802(AUDIO A/D CONVERTER)
AUDIO A/DCONVERTER
789
1314
6
2
L-CHR-CH
MUTE
R-CHL-CH
101112
CN701AUDIO(L)-OUT 14AUDIO(R)-OUT 16DVD-AUDIO-MUTE 12AUDIO(L)-IN 20AUDIO(R)-IN 18
28 28SPDIFCN101 CN1151
DIGITALAUDIO OUT(COAXIAL)
JK1209 (REAR)BUFFER
Q1803
BOARD POWER
WF7
NOTE: BOARD MEANS PRINTED CIRCUIT BOARD.
1-10-3 E7B71BLV
TO DIGITALSIGNALPROCESSBLOCKDIAGRAM
TO SYSTEM CONTROL BLOCK DIAGRAM
(VIDEO SIGNAL PROCESS)IC1201
TU1701(TUNER UNIT)
17 VIDEO OUT
CN120110 VIDEO-Y/CVBS-IN8 VIDEO-C-IN
24 VIDEO-Y(I/P)-OUT26 VIDEO-Cr/Pr-OUT28 VIDEO-Cb/Pb-OUT30 VIDEO-Y(I)-OUT22 VIDEO-C-OUT
JK1211(REAR)S-VIDEOIN2
3 4
21
CY
Y
JK1213(REAR)S-VIDEOOUT
VIDEO-Y-OUT
VIDEO-Cb/Pb-OUT
VIDEO-Cr/Pr-OUT
21
3 4CY
JK1212(FRONT)S-VIDEOIN1
3 4
21
C
VIDEO-IN2
JK1204 (REAR)
VIDEO-IN1
JK1201 (FRONT)
DRIVER
VIDEO OUT2VIDEO-GVIDEO-BVIDEO-R
19CN2001 CN1801
VIDEO-OUT28 8
BOARD JACK BOARD JACK
JK2001
CN1801 CN2001VIDEO-IN210 10 VIDEO
IN220
JK2001
VIDEO IN120
JK1206
11 VIDEO-G-IN13 1315 VIDEO-B-IN12 12 7
VIDEO OUT1VIDEO-GVIDEO-BVIDEO-R
19117
15
VIDEO-R-IN14 14
JK1206
JK1205 (REAR)
12
62
161420
SW
SW
SW
SW
IICI/F
SW
SW
SW
GCL
SW
SW
AGC
AGC
LPF
1007
19
22485049
30
61
59
5152535557
46
44
45
DRIVER
DRIVER
DRIVER
40
38
39
DRIVER
DRIVER
DRIVER
DRIVER FBC
MUTE FBC
MUTE
MUTE
MUTE
MUTE
SW
DRIVER FBC
DRIVER
DRIVER
36
34
+
+
65
64
SW
SW
SW
SW
LPF
Q1202
Q2003
BUFFER
BUFFER
Q1201BUFFER
Q1204BUFFER
+
REC VIDEO SIGNAL PB VIDEO SIGNAL
IC1641 (VPS)
VPS-VSDA
SDA
DAVN-L
DAVN-L
SCL
SCL
64243
147
16
BOARD POWER
WF5
WF4WF2
WF3
WF1
NOTE: BOARD MEANS PRINTED CIRCUIT BOARD.
Video Block Diagram
1-10-4
Audio Block Diagram
E7B71BLA
IC1201(AUDIO SIGNAL PROCESS)
JK1210
Q1802
Q1806
AUDIO(L)-OUT2
BOARD POWER
AUDIO(R)-OUT2
JK1202
AUDIO(L)-IN1
AUDIO(R)-IN1
JK1203
JK1204
AUDIO(L)-IN2
AUDIO(R)-IN2
SIF OUT
5 5TU-AUDIO(L)
2 2AUDIO-MUTE
2 2SIF
4 4TU-AUDIO(R)
3 3AUDIO(L)-OUT2
6 6AUDIO(L)-IN25 5AUDIO(R)-IN2
1 1AUDIO(R)-OUT2
(OP AMP)IC1203
TO DIGITALSIGNALPROCESSBLOCKDIAGRAM
TU1701 (TUNER UNIT)
OPAMP
OPAMP
7
1
7
2
6
MUTE-ON
DRIVE
Q1807
(FRONT)
(REAR)
(REAR)
(FRONT)
MUTE-ON
CN1201
(OP AMP)IC1202
OPAMP
OPAMP
SW
SW
SW
2
6
1
7
REC AUDIO SIGNAL PB AUDIO SIGNAL
Q1804MUTE-ON
Q1805MUTE-ON
Q2002MUTE-ON
Q2001MUTE-ON
IF SINALPROCESS
BOARD AFV
BOARD JACK
CN1701
CN1801 CN2001
CN1
JK2001
AUDIO(R)-IN2AUDIO(L)-OUT2AUDIO(R)-OUT2
2
AUDIO(L)-IN26
1
3
JK1206
AUDIO(R)-IN1AUDIO(L)-OUT1AUDIO(R)-OUT1
2
AUDIO(L)-IN16
1
3
79
80
76
77
90
67
68
94859282
8993849181
SW
SW
72
SW 71
SW 74
SW
SW
SW
73
14 AUDIO(L)-OUT16 AUDIO(R)-OUT12 DVD-AUDIO-MUTE20 AUDIO(L)-IN18 AUDIO(R)-IN
DVD-AUDIO-MUTESCART-AUDIO-MUTE
AUDIO-MUTE
TO SYSTEM CONTROLBLOCK DIAGRAM
Q1801DRIVE
IICI/F
4243
TO SYSTEM CONTROL BLOCK DIAGRAM
SDASCL
WF6
NOTE: BOARD MEANS PRINTED CIRCUIT BOARD.
1-10-5
Power Supply Block Diagram
AC1001 F1001T1.6A L 250V
LINE
FILTER
L1004 D1001 - D1004
BRIDGERECTIFIER
3
5
Q1003
Q1002
Q1001
Q1101
7
8
1
23
4
IC1001ERRORVOLTAGE DET
T1001
BOARD POWERBOARD POWER SUPPLY
HOT CIRCUIT. BE CAREFUL.
11
12
13
14
15
16
17
18
19
20
25 P-ON+2.5V(1)
14 P-ON+3.3V15 P-ON+3.3V16 P-ON+3.3V9 P-ON+5V
4 EV+10.5V5 EV+10.5V
19 VI+1.2V
EV+3.3V
PWSW
+32V
AL-30V
AL+12V
TIMER+5V
P-ON+10V
EV+5V
Q1155,Q1157
SW+12V
Q1159SW+3.3V
AL+5V
F2
F1
CN1103 CN1105 CN11525 AL+44V 5
4 FAN-AL+12V 4
2 AL+5V 2
CN1102 CN1104
3 AL-30V
7 AL+3V
1
3
7
1F1IC1152+3.3V REG.
+2.5V REG.IC1151
+5V REG.
BOARDJUNCTION
CN1106131211109
131211109
P-ON+3.3VAL+5V
P-ON+5VQ1154
CN1151
SW+5V
Q1158
Q1508
AUDIO+5V+5V REG.Q1163
+10V REG.Q1160
SW+5V
5 AL+4V 5
2 F2 2
3 AL+12V 3
1 AL+5V 1
TO SYSTEMCONTROLBLOCKDIAGRAM
Q1156SW+9V AL+9V
REG.IC1153
24 P-ON+2.5V(1)
6 EV+10.5V
10 P-ON+5V11 P-ON+5V
20 VI+1.2V21 VI+1.2V
1 12 23 35 57 7
CN1152CN1106 TO DVD MAIN BOARDCN101
FAN-AL+12V
VIDEO+5V
Q1164
REG-CONT TO SYSTEM CONTROLBLOCK DIAGRAM
HOT COLD
CAUTION !Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.If Main Fuse (F1001) is blown , check to see that all components in the power supplycircuit are not defective before you connect the AC plug to the AC power supply.Otherwise it may cause some components in the power supply circuit to fail.
"Ce symbole reprèsente un fusible à fusion rapide."
CAUTION !For continued protection against fire hazard,replace only with the same type fuse.ATTENTION : Pour une protection continue les risqesd'Incele n'utiliser que des fusible de même type.Risk of fire-replace fuse as marked.
"This symbol means fast operating fuse."
A V
FNOTE:The voltage for parts in hot circuit is measured usinghot GND as a common terminal.
NOTE: BOARD MEANS PRINTED CIRCUIT BOARD.
E7B71BLP
1-11-1 R2P_SC
SCHEMATIC DIAGRAMS / BOARD’S AND TEST POINTS
Standard Notes
WARNINGMany electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts that have these special safety characteristics are identified in this manual and its supplements; electrical components having such features are identified by the mark " ! " in the schematic diagram and the parts list. Before replacing any of these components, read the parts list in this manual carefully. The use of substitute replacement parts that do not have the same safety characteristics as specified in the parts list may create shock, fire, or other hazards.
Notes:1. Do not use the part number shown on these
drawings for ordering. The correct part number is shown in the parts list, and may be slightly different or amended since these drawings were prepared.
2. All resistance values are indicated in ohms
(K=103, M=106).
3. Resistor wattages are 1/4W or 1/6W unless otherwise specified.
4. All capacitance values are indicated in µF
(P=10-6 µF).
5. All voltages are DC voltages unless otherwise specified.
6. Electrical parts such as capacitors, connectors, diodes, IC’s, transistors, resistors, switches, and fuses are identified by four digits. The first two digits are not shown for each component. In each block of the diagram, there is a note such as shown below to indicate these abbreviated two digits.
NOTE: BOARD MEANS PRINTED CIRCUIT BOARD.
1-11-2 R3PT_SC
LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWING PAGES:
1. CAUTION:
FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE SAME TYPE FUSE.
2. CAUTION:
Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F1001) is blown, first check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail.
3. Note:1. Do not use the part number shown on the drawings for ordering. The correct part number is shown in the
parts list, and may be slightly different or amended since the drawings were prepared.
2. To maintain original function and reliability of repaired units, use only original replacement parts which are listed with their part numbers in the parts list section of the service manual.
4. Voltage indications for PLAY and REC mode on the schematics are as shown below:
5. How to read converged lines
6. Test Point Information
2 31 5.0(2.5)
5.0
The same voltage for both PLAY & REC modes
Indicates that the voltage is not consistent here.
PLAY modeREC mode
(Unit: Volt)
3
2
1
A B C D
1-B1
1-D3
AREA D3
AREA B1
1-D3
Distinction AreaLine Number (1 to 3 digits)
Examples:1. "1-D3" means that line number "1" goes to the line number "1" of the area "D3". 2. "1-B1" means that line number "1" goes to the line number "1" of the area "B1".
: Indicates a test point with a jumper wire across a hole in the BOARD.
: Used to indicate a test point with a component lead on foil side.
: Used to indicate a test point with no test pin.
: Used to indicate a test point with a test pin.
1-11-3
DVD MAIN 1/5 Schematic Diagram
E7B71SCD1
NOTE:1. The order of pins shown in this diagram is different from that of actual IC101.2. IC101 is divided into five and shown as IC101 (1/5) ~ IC101 (5/5) in this DVD Main Schematic Diagram Section.
NOTE: BOARD MEANS PRINTED CIRCUIT BOARD.
1-11-4
DVD MAIN 2/5 Schematic Diagram
E7B71SCD2
NOTE:1. The order of pins shown in this diagram is different from that of actual IC101.2. IC101 is divided into five and shown as IC101 (1/5) ~ IC101 (5/5) in this DVD Main Schematic Diagram Section.
NOTE: BOARD MEANS PRINTED CIRCUIT BOARD.
1-11-5
DVD Main 3/5 Schematic Diagram
E7B71SCD3
NOTE:1. The order of pins shown in this diagram is different from that of actual IC101.2. IC101 is divided into five and shown as IC101 (1/5) ~ IC101 (5/5) in this DVD Main Schematic Diagram Section.
NOTE: BOARD MEANS PRINTED CIRCUIT BOARD.
1-11-6
DVD Main 4/5 Schematic Diagram
E7B71SCD4
NOTE:1. The order of pins shown in this diagram is different from that of actual IC101.2. IC101 is divided into five and shown as IC101 (1/5) ~ IC101 (5/5) in this DVD Main Schematic Diagram Section.
NOTE: BOARD MEANS PRINTED CIRCUIT BOARD.
1-11-7
DVD Main 5/5 Schematic Diagram
E7B71SCD5
NOTE:1. The order of pins shown in this diagram is different from that of actual IC101.2. IC101 is divided into five and shown as IC101 (1/5) ~ IC101 (5/5) in this DVD Main Schematic Diagram Section.
NOTE: BOARD MEANS PRINTED CIRCUIT BOARD.
1-11-8
POWER 1/5 Schematic Diagram
E7B71SCP1
*1 NOTE
IC1502A
IC1502B
R3112N191A-TR-FA/BU4219G-TR
PST3619NR
Group A Group B
C1507A
C1507B
0.015
0.1
These components (IC1502A, C1507A, IC1502B, C1507B) can be used in any models. However, you cannot mix components under Group A with the ones under Group B. You can choose either Group. The difference between Group A and Group B is shown below.
----------
----------
----------
----------
NOTE: BOARD MEANS PRINTED CIRCUIT BOARD.
1-11-9
POWER 2/5 Schematic Diagram
E7B71SCP2
NOTE: BOARD MEANS PRINTED CIRCUIT BOARD.
5G 4G 3G 2G 1G7G 6G
a
d
g
h
h
gc b
efREPEATPMREC
VCD VCR DVD RXP SPLP EP
SLPP.SCAN
SEP
WCDT C
7G 6G 5G 4G 3G 2G 1G
a
b
c
d
e
f
g
c
d
e
f
gg
c
d
e
f
g
c
d
e
f
g
c
d
e
f
g
c
d
e
f
g
h h
i
a
b
a
b
a
b
a
b
a
b
FL1501 MATRIX CHART
REPEAT
PMREC
VCD VCR DVD R
XPSPLPEPSLP
P.SCANSEP
WCD
T C
1-11-10 E7B71SCP3
POWER 3/5 Schematic DiagramNOTE: BOARD MEANS PRINTED CIRCUIT BOARD.
1-11-11 E7B71SCP4
POWER 4/5 Schematic DiagramNOTE: BOARD MEANS PRINTED CIRCUIT BOARD.
1-11-12 E7B71SCP5
POWER 5/5 Schematic DiagramNOTE: BOARD MEANS PRINTED CIRCUIT BOARD.
1-11-13
CAUTION !Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.If Main Fuse (F1001) is blown , check to see that all components in the power supplycircuit are not defective before you connect the AC plug to the AC power supply.Otherwise it may cause some components in the power supply circuit to fail.
NOTE:The voltage for parts in hot circuit is measured usinghot GND as a common terminal.
"Ce symbole reprèsente un fusible à fusion rapide."
CAUTION !For continued protection against fire hazard,replace only with the same type fuse.ATTENTION : Pour une protection continue les risqesd'Incele n'utiliser que des fusible de même type.Risk of fire-replace fuse as marked.
"This symbol means fast operating fuse."
A V
F
E7B71SCPS
POWER SUPPLY & JUNCTION Schematic DiagramNOTE: BOARD MEANS PRINTED CIRCUIT BOARD.
1-11-14 E7B71SCSW
NOTE: BOARD MEANS PRINTED CIRCUIT BOARD.
SWITCH Schematic Diagram
1-11-15 E7B71SCJ
NOTE: BOARD MEANS PRINTED CIRCUIT BOARD.
JACK Schematic Diagram
1-11-16 E7B71SCAFV
NOTE: BOARD MEANS PRINTED CIRCUIT BOARD.
AFV Schematic Diagram
1-11-17 BE7B00F01011A
NOTE: BOARD MEANS PRINTED CIRCUIT BOARD.
BOARD POWER Top View
1-11-18
WF4PIN 28 OFCN1201
WF2PIN 22 OFCN1201
WF3
WF7PIN 28 OFCN1151
WF5PIN 26 OFCN1201
WF6PIN 143 OFCN1201
WF1PIN 24 OFCN1201PIN 30 OF
IC1201
BE7B00F01011A
BOARD POWER Bottom ViewNOTE: BOARD MEANS PRINTED CIRCUIT BOARD.
1-11-19 BE7B00F01021A
NOTE: BOARD MEANS PRINTED CIRCUIT BOARD.
NOTE:The voltage for parts in hot circuit is measured usinghot GND as a common terminal.
CAUTION !For continued protection against fire hazard,replace only with the same type fuse.
CAUTION !Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.If Main Fuse (F1001) is blown , check to see that all components in the power supplycircuit are not defective before you connect the AC plug to the AC power supply.Otherwise it may cause some components in the power supply circuit to fail.
Because a hot chassis ground is present in the powersupply circut, an isolation transformer must be used.Also, in order to have the ability to increase the inputslowly, when troubleshooting this type power supplycircuit, a variable isolation transformer is required.
BOARD POWER SUPPLY Top View
1-11-20
NOTE:The voltage for parts in hot circuit is measured usinghot GND as a common terminal.
CAUTION !For continued protection against fire hazard,replace only with the same type fuse.
CAUTION !Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.If Main Fuse (F1001) is blown , check to see that all components in the power supplycircuit are not defective before you connect the AC plug to the AC power supply.Otherwise it may cause some components in the power supply circuit to fail.
Because a hot chassis ground is present in the powersupply circut, an isolation transformer must be used.Also, in order to have the ability to increase the inputslowly, when troubleshooting this type power supplycircuit, a variable isolation transformer is required.
NOTE: BOARD MEANS PRINTED CIRCUIT BOARD.
BE7B00F01021A
BOARD POWER SUPPLY Bottom View
1-11-21
BE7B00F01021B
BE7B00F01011B
BOARD JUNCTION
Top View
BOARD JUNCTION
Bottom View
BOARD SWITCH Top View BOARD SWITCH Bottom View NOTE: BOARD MEANS PRINTED CIRCUIT BOARD.
1-11-22
BOARD AFV Top View
BE6800F01091
BOARD AFV Bottom View
BOARD JACK Top View BOARD JACK Bottom View
BE7B00F01021C
NOTE: BOARD MEANS PRINTED CIRCUIT BOARD.
WAVEFORMS
WF6
AUDIO(L)-OUT
Pin 14 of CN1201
1V 0.5ms
WF1 Pin 24 of CN1201
WF3 Pin 30 of IC1201
WF4
VIDEO-Cb
Pin 28 of CN1201
0.2V 20µsec
WF5
VIDEO-Cr
Pin 26 of CN1201
0.2V 20µsec
SPDIF 1V 0.1µsec
WF7 Pin 28 of CN1151
WF2 Pin 22 of CN1201
VIDEO-Y 0.2V 20µsec
VIDEO-C 0.2V 20µsec
VIDEO-CVBS 0.5V 20µsec
NOTE:Input: COLOR BAR SIGNAL (WITH 1KHz AUDIO SIGNAL)
1-12-1 R3PWF
118
217
415
514
613
712
811
910
109
118
127
136
145
154
163
172
316
DVD MECHANISM
DVD MECHANISM & DVD MAIN BOARD ASSEMBLY
BOARD RELAY
BOARD ENCODER
CN201
CN301
CN1003
HW
+H
W-
BOARD POWERBOARD JACK BOARD AFV
BOARDJUNCTION
BOARDPOWERSUPPLY
GN
D1
1G
ND
22
EV
+10.5V
44
EV
+10.5V
55
EV
+10.5V
66
GN
D7
7G
ND
88
P-O
N+
5V9
9P
-ON
+5V
1010
P-O
N+
5V11
11G
ND
1212
GN
D13
13P
-ON
+3.3V
1414
P-O
N+
3.3V15
15P
-ON
+3.3V
1616
GN
D17
17G
ND
1818
CN701
CN1201
CN101
JW001
JW002
JW010
JW2001
CN1151
AC CORDAUDIO(L)-OUT2
AUDIO(R)-OUT2
AUDIO(L)-IN2
AUDIO(R)-IN2
AUDIO(L)-IN1
AUDIO(R)-IN1
VIDEO-IN1
FRONT
VIDEO-IN2
DIGITALAUDIO OUT(COAXIAL)
S-VIDEOOUT
S-VIDEOIN2
S-VIDEOIN1
GN
D3
3
BOARDSWITCH
CN3001
CN1502 CN1701
CN1CN2001
CN1801
CN1152 CN1106JW1001
JW1002
CN1102CN1104
CN1103CN1105KE
Y-11
1
GN
D3
3K
EY-2
22
AUD
IO(R
)-OU
T21
1
AUD
IO(L)-O
UT2
33
GN
D4
4A
UD
IO(R
)-IN2
55
AU
DIO
(L)-IN2
66
SC
2-IN7
7V
IDE
O-O
UT
28
8G
ND
99
VID
EO
-IN2
1010
16P11
11V
IDE
O-B
-IN12
12V
IDE
O-G
-IN13
13V
IDE
O-R
-IN14
14A
L+12V
1515
AU
DIO
-MU
TE
22
NU
11
GN
D3
3T
U-A
UD
IO(R
)4
4T
U-A
UD
IO(L)
55
P-O
N+
5V6
6P
-ON
+5V
77
IIC-B
US
-SC
L8
8IIC
-BU
S-S
DA
99
SIF
22
VIDEO-Y-OUT
VIDEO-Cb/Pb-OUT
REAR
VIDEO-Cr/Pr-OUT
SLEDSENSOR SPINDLE
MOTOR
123
PICKUP
FO
CU
SA
CT
UATO
R
TR
AC
KIN
GA
CT
UATO
R
TILT
AC
TU
ATOR
M
VI+
1.2V19
19V
I+1.2V
2020
VI+
1.2V21
21G
ND
2222
GN
D23
23P
-ON
+2.5V
(1)24
24P
-ON
+2.5V
(1)25
25G
ND
2626
GN
D27
27S
PD
IF28
28G
ND
2929
1V2C
ON
T30
30
CN1001
W V U VC
CH
U+
HU
-H
V+
HV
-
VH
-T-S
CN
3T-S
CN
2G
ND
SL+
SL-
SW
1
CN1002
1234567891011
MSLEDMOTOR
DVD MAIN BOARD
VIDEO-Cb/Pb-O
UT3
28
VIDEO-Cr/Pr-O
UT5
26
VIDEO-Y(I/P)-O
UT7
24
AL-30V 33
AL+5V 1010AL+5V 99
GND 44AL+4V 55GND 66AL+3V 77GND 88
AL+12V 1111FAN-AL+12V 1212AL+44V 1313GND 1414GND 1515
F1 11F2 22
12345678
1234567
12345678
1234567
12
34
56
78
910
1112
1314
1516
1718
1920
21
12
34
56
78
910
1112
1314
1516
1718
1920
21
JK1206
JK2001
CN1601
1FA
N+
12V2
FAN
- GN
D
FAN
1F
CS
(+)
4T
RK
(-)3
TR
K(+
)2
FC
S(-)
6T
ILT(-)
5T
ILT(+
)
7F
PD
-VO
UT
9F
PD
-VC
C10
GN
D11
FP
D-V
SW
8F
PD
-VC
12G
ND
14R
F(+
)15
C16
B17
F18
E19
D20
PD
-SW
21H
22G
23A
24P
D-V
CC
25P
D-V
C26
VC
C1
27V
CC
228
TH
29G
ND
30G
ND
31IIN
R32
IINW
33IIN
E34
GN
D35
HF
SW
36E
NA
BLE
37O
CE
38G
ND
39O
CW
40LD
SW
13R
F(-)
DVD/CD LASER DIODE DRIVEPDIC FPDIC
SU
B-R
XD
11
RD
Y2
2S
UB
-TX
D3
3
VIDEO-Y/CVBS-IN
1010
GN
D9
9
SY
S-R
ES
ET
44
SU
B-S
CLK
55
GN
D6
6G
ND
77
VID
EO
-C-IN
88
AUD
IO(R
)-OU
T16
16
AU
DIO
+5V
1111
DVD-AUDIO-M
UTE12
12G
ND
1313
AUD
IO(L)-O
UT
1414
GN
D15
15
GN
D17
17A
UD
IO(R
)-IN18
18G
ND
1919
AU
DIO
(L)-IN20
20G
ND
2121
VID
EO
-C-O
UT
2222
GN
D23
23
GN
D25
25
GN
D27
27
GN
D29
29VID
EO-Y(I)-O
UT
3030
CD
-LD
DV
D-LD
NOTE: BOARD MEANS PRINTED CIRCUIT BOARD.
WIRING DIAGRAM
1-13-1 E7B71WI
1-14-1 R2NTI
SYSTEM CONTROL TIMING CHARTS
INNER-SWopen?
Rezero 1
To discdistintion
Power on
Yes
Yes
No
Yes
Tray insertion
[ Tray Open ] button is pressed.
[ Tray Open ] button is pressed.
Tray ejection
Tray ejection completion
Push Close
Rezero 2
INNER-SWopen?
Is TimerET1 passed?
INNER-SWopen?
Is TimerET4 passed?
Is slit S5 passed?
Is TimerET3 passed?
Is TimerET1 passed?
Retry OK?
Is slit S1passed?
Is not slit passed?
Is TimerET2 passed?
No
No
Case 1
Case 2
Yes
Yes
YesYes
No
No
Case 4[ open ] button is pressed.
Case 5Retry.
Case 3[ open ] button is pressed.
No
No
Yes
Yes
Yes No
Yes
Yes
No
No
No
No
Tray insertion
In case of "No" by the 6th time retry.
1-14-2 R2NTI
Parameter
Tray open
Tray close
V*: Voltage (HEX) S*: Encoder pulse (HEX) T*: Event timer ET*: Error
detection timer
V0: 2.0 V (00d) S1: 300 (12c) T1: 0.1 s ET1: 5.0 s
V1: 4.5 V (022) S2: 3300 (ce4) T2: 3.0 s ET2: 5.0 s
V2: 2.2 V (010) S3: 3935 (f5f) T3: 3.0 s ET3: 3.0 s
V3: 2.4 V (013) S4: 0 (000) T4: 0.1 s ET4: 3.0 s
V4: 6.0 V (030) S5: 3000 (bb8) T5: 0.1 s
SLED
Encoder pulse
INNER-SW
close
open
Tray insersion direction
Tray ejection direction
Timer ET1
S1
S2
S3
ET2
T1
V0
V2
V1
SLED
INNER-SW
Timer
close
open
Tray insersion direction
Tray ejection direction
S5
V3
V4
S4
ET3 ET4
1-14-3 R2NTI
Push close
Case 1
Case 2
SLED
Encoder pulse
S5
T3
V3
V4
ET4
Push Close
INNER-SW
close
open
Tray insersion direction
Timer
SLED
open
Tray insersion direction
close
INNER-SW
TimerT2
Rezero 1
ET4
V3
V4
SLED
INNER-SW
open
Rezero 2
Tray insersion direction
Tray ejection direction
close
V0
V0
1-14-4 R2NTI
Case 3 (When [OPEN] button is pressed before the S5 passage.)
Case 4 (When [OPEN] button is pressed after the S5 passage.)
It starts opening after making closing complete once.
Case 5 (Retry.)
Retry frequency V1+
1st time retry 6 v
2nd time retry 7 v
3rd time retry 8 v
4th time retry 9 v
5th time retry 9 v
6th time retry 9 v
SLED
Encoder pulse
Tray ejection direction
T1Timer
V2
SLED
Tray ejection direction
S1
V1+
V2
6v
open
Tray insersion direction
Start retry.close
INNER-SW
1-15-1 E7B71PIN
IC PIN FUNCTION DESCRIPTIONS
IC1501 (SUB MICRO CONTROLLER)
Pin No.
IN/OUT
Signal Name Function
1 IN KEY-1 Key Data Input 1
2 IN KEY-2 Key Data Input 2
3 IN POW-SW Abnormal Voltage Detection
4 IN AFT Tuner Voltage Input Signal
5 - NU Not Used
6 IN EV+3.3V +3.3V Power Supply
7 IN BUP+3.3V +3.3V Power Supply
8 OUT OSC2 Main Clock Output
9 IN OSC1 Main Clock Input
10 - VSS Ground
11 IN XCIN Sub Clock Input
12 OUT XCOUT Sub Clock Output
13 - GND Ground
14 IN RESET Micro Controller Reset Signal
15 OUT 8POUT-1Control SCART 18Pin Level by using 8POUT-1 and 8POUT-2
16 OUT 8POUT-2Control SCART 18Pin Level by using 8POUT-1 and 8POUT-2
17 - NU Not Used
18 OUT SUB-TXD Transmission Data to Main Micro Controller
19 IN SUB-RXD Reception Data from Main Micro Controller
20 OUT SUB-SCLK Communication Clock with Main Micro Controller
21 - NU Not Used
22 OUT SYS-RESET System Reset Signal
23 - NU Not Used
24 IN DAVN-L VPS/PDC Data Receive = “L”
25 - NU Not Used
26 OUT 1V2CONT Power Regulator Control Signal
27 IN REMOTE Remote Signal Input
28 - NU Not Used
29 IN RDYReady/Busy communication Control with Main Micro Controller
30 IN P-DOWN Power Voltage Down Detector Signal
31 - NU Not Used
32 - NU Not Used
33 IN/OUT SDA Serial Data
34 OUT SCL Serial Clock
35 - NU Not Used
36 - NU Not Used
37 INDVD-AUDIO-MUTE
DVD-Audio Mute Control Signal
38 OUT AUDIO-MUTE Audio Mute Control Signal
39 OUTSCART-AUDIO-MUTE
SCART-Audio Mute Control Signal
40 - NU Not Used
41 - NU Not Used
42 - NU Not Used
43 - NU Not Used
44 - NU Not Used
45 - NU Not Used
46 - NU Not Used
47 - NU Not Used
48 OUT FL-DIN Serial Data
49 OUT FL-STB Serial Interface Strobe
50 OUT FL-SCL Serial Clock
51 - NU Not Used
52 OUT REG-CONT
Power Regulator Control Signal
53 OUT PWSW Power ON Signal Output
54 - NU Not Used
55 OUT FAN-CONT2 Fan Motor Control Signal
56 - NU Not Used
57 - NU Not Used
58 - NU Not Used
59 - NU Not Used
60 - NU Not Used
61 - AVss AVSS (GND)
62 IN FAN-LOCK Fan Motor Lock Detection
63 IN AGC IF AGC Comparator Signal
64 IN SC2-IN Input Signal from Pin 8 of SCART2
Pin No.
IN/OUT
Signal Name Function
1-15-2 E7B71PIN
IC2001 (VFD DRIVER)
Pin No.
IN/OUT
Signal Name Function
1 IN CLK Serial Clock
2 IN STB Serial Interface Strobe
3 - NU Not Used
4 - NU Not Used
5 - VSS GND
6 - VDD Power Supply
7
OUT
a
Segment Output
8 b
9 c
10 d
11 e
12 f
13 g
14 h
15 - VEE Pull Down Level
16 OUT i Segment Output
17
OUT
7G
Grid Output
18 6G
19 5G
20 4G
21 3G
22 2G
23 1G
24 - VDD Power Supply
25 - VSS GND
26 IN OSC Oscillator Input
27 - NU Not Used
28 IN DIN Serial Data Input
1-16-1 E7B71LE
LEAD IDENTIFICATIONS
33
12
22
23
111
44
34
80
31
50
51
301
100
81
Note:A: AnodeK: CathodeE: EmitterC: CollectorB: BaseR: ReferenceS: SourceG: GateD: Drain
E C B
KRC103M-AT/PKTA-1266-GR-AT/PKTA1267-Y-AT/PKTA1273-Y-AT/PKTC3199-(BL,Y)-AT/P
E C B
EL817A
G D S
2SK3566
1 4
8 5
KIA4558P/PRC4580IP
28 15
14
SC16313G
1
SSM3K15F(TE85L F)
D
G S
2SC1815-GR(TE2 F T)2SC2001-T-A-KKTC3203-Y-AT/PKTC3266-GR-AT/P
KIA431-AT/P
48
17
32
33
161
64
49
MN101C77A FM
24 13
12
LC74793JM-TLM-E
1
MSP3417G-QG-B8-V3 HA118326APF-E
1 2 3 4
PQ070XF01SZH
1 2 3
5 4
BU4219G-TRPST3619NRR3112N191A-TR-FA
1: R2: A3: K
1 2 3
1
2
4
3
1: A2: K3: E4: C