Location N-m lb-ft Location N-m lb-ft Location N-m lb-ft

Center Support Fluid Feed Bolt 11-16 8-12

Trans. Insulator and Retainer to Case

81-108 60-80Trans. Insulator and Retainer to Crossmember

81-108 60-80

Cooler Line To Case Connector 27-33 20-24

Man. Cont. Valve Detent Lever Spring to Case

9-11 6.6-8 Flywheel to Torque Converter 30-41 22-30

Radiator Nipple Connector 23-31 17-23 Reinforcing Plate

to Case 9-11 6.6-8Inner Manual Valve Detent Lever Nut

41-54 30-40

Radiator to Tube Connectors 27-31 20-23 Stator Support to

Pump Body 9-11 6.6-8Low/Rev. OWC Inner Race to Case

24-34 18-25

Radiator to Tube Connectors 24-30 18-22

Cooler Bypass Valve to Case(inlet)

27-33 20-24 Line Press. To Case Plug 8-16 6-12

Cooler Tube to CBV 16-24 12-18

Cooler Bypass Valve to Case(outlet)

33-40 25-29Main and Lower Control Body to Case

9-11 6.6-8

Aux. Cooler tube 11-14 8-10 Trans to Engine Except 7.3L 41-54 30-40

Main Acc. And Sol. Body to Case

9-11 6.6-8

Aux. Cooler tube 22-30 16-22 Trans to Engine With 7.3L 52-70 39-52 Digital Trans.

Range Sensor 8-10 5.9-7.4

Control Assembly to Pump 24-31 18-23 Trans.Crossmem

ber to Frame 68-95 50-70 Int/OD Cyl. Fluid Feed Bolt 8-14 6-10

Torque Converter Drain Plug 24-27 18-20

Vapor Management Valve to Cowl

7.6-10.4 5.6-7.7 Trans. Pan to Case 14-16 10-12

Flywheel Inspection Cover to 7.3L

18-23 13-17Output Shaft Drive Sprocket Speed Sensor

8-10 5.9-7.4 Pump Body To Case 24-31 18-23

Flywheel Inspection Cover Except 7.3L

30-39 22-29 Turbine Shaft Sensor 8-10 5.9-7.4Parking Prawl Abutment to Case

22-27 16-20

Extension Housing to Case 41-54 30-40

Cooler By-Pass Valve Fitting to Case (front&rear)

33-40 24-29Parking Rod Guide Plate to Case

22-27 16-19

Liters16.1Approximately Dry Fill Capacity16.7 1

Approximately Dry Fill Capacity

4R100 with a 26 Plate Oil-To-Air Cooler

17.7 1

Approximately Dry Fill Capacity

1 5.4L applications within tank coolers and OTA may require an additional few ouncesPage 1

Torque Specifications

Fluid Fill CapacityTransmission Type Quarts

4R100 with a 20 Plate Oil-To-Air Cooler

17.1

Approximately Dry Fill Capacity

GearIntermediate

Band Coast Over- drive Intermediate Direct For- ward Re- verse Drive Coast Drive Coast Drive CoastD first - ab - - - apply - HOLD ab - - HOLD O/R

D second - ab - apply - apply - HOLD ab HOLD O/R O/R O/RD third - ab - apply apply apply - HOLD ab O/R O/R O/R O/RD fourth - - apply apply apply apply - O/R O/R O/R O/R O/R O/R

1 - apply - - - apply apply HOLD CC - - HOLD -2 apply apply - apply - apply - HOLD CC HOLD BA O/R O/R

reverse - apply - - apply - apply HOLD CC O/R O/R - -ab

O/D - OverdriveO/R - OverrunningCC - Coast Clutch appliedBA - Band Applied

Page 2

Pin No. Gas Diesel *1 71,97 71,972 11 13 6 274 54 285 20 5367 37 378 91 919

Trans. Fluid Temp. Sensor (return)N/A

Ground (Shift Sol. "B" (2))Ground (Shift Sol. "A" (1))Ground (Converter Clutch Sol.)Ground (Coast Clutch Sol.)N/ATrans. Fluid Temp. Sensor

The coast clutch solenoid and clutch is controlled by the PCM in certain applications in D .

Check Ball Location

Solenoid Assembly Pin IdentificationPCM Connector

DescriptionV.P.W.R. for Solenoids

Friction Elements One-Way ClutchesOverdrive Intermediate Low

With the transmission control switch pressed, in D , the coast clutch is applied and the O/D one-way clutch is bypassed.

Band Application Chart

1011 81 8112 71,97 71,97

oC oF Resistance (Ω)

-40 to -20 -40 to -4 1062k - 284k-19 to -1 -3 to 31 284k - 100k

0 to 20 32 to 68 100k - 37k21 to 40 69 to 104 37k - 16k41 to 70 105 to 158 16k - 5k71 to 90 159 to 194 5k - 2.7k91 to 110 195 to 230 2.7k - 1.5k111 to 130 231 to 266 1.5k - 0.8k131 to 150 267 to 302 0.8k - 0.54k

Selector Range

Command Gear Shift Sol. "A" Shift Sol "B" TCC Sol. Coast Clutch

P/R/N 1 O X * *D 1 O X * * O OnD 2 O O * * X OffD 3 X O * *D 4 X X * *D

CanceledMan 2 2 * * * OMan 1 2 X X X OMan 1 1 O X X O

D 2 1 D 2 1

1st 4 2 1 1st 1 2 12nd 3 2 2 2nd 1 2 13rd 3 2 2 3rd 4 2 24th 4 2 2 4th 4 2 2

Page 3

D 2 1 D 2 1

1st 1 2 1 1st 2 2 12nd 2 2 1 2nd 2 2 13rd 2 2 1 3rd 3 2 24th 1 2 1 4th 3 2 2

4R100 and E4OD Extention Housings

Shift Solenoid Application Chart cont.

Shift Solenoid "A" Always On Shift Solenoid "B" Always On

PCM Gear Controlled

Lever PositionPCM Gear Controlled

Lever Position

Actual Gear Actual Gear

Shift Solenoid Application Chart

1st to 3rd Gear Only, SSA, TCC, SSB, Same as O/D, CCS Always On

Shift Solenoid "A" Always Off Shift Solenoid "B" Always Off

PCM Gear Controlled

Lever PositionPCM Gear Controlled

Lever Position

Actual Gear Actual Gear

EPC Solenoid 11 and 12 3.0-5.0 ΩTrans. Fluid Temp. Sensor 7 and 8 See Chart

TCC Solenoid, Diesel (PWM) 1 and 4 10-20 ΩCoast Clutch Solenoid 1 and 5 20-30 Ω

Shift Solenoid "A" (1) 1 and 3 20-30 ΩTCC Solenoid, Gas (on-off) 1 and 4 20-30 Ω

Solenoid Resistance Trans. Fluid Temp Sensor

Solenoid Solenoid Body Pin Numbers ResistanceShift Solenoid "B" (2) 1 and 2 20-30 Ω

N/AE.P.C. (Electronic Press. Control)V.P.W.R. for E.P.C. Solenoid

* All Except Diesel in Cal. (see "Gas" Application for Cal. Diesel)

REV 5/99

COPYRIGHT 1999, PRECISION INTERNATIONALPage 4

We would like to thank ATSG for the information they provided in helping to create this Precision Pointer.

TECHNICAL DEPARTMENT IS-36000R

All of this information is based on the latest technical data available at time of printing. Although every care has been taken to detail & acccuracy, Precision International accepts no liability for inaccuracies, updates, changes &/or misprints in this publication.