TOPAZ PARTFILL - Irrigation Direct · 2017. 11. 7. · 3 4 TPPP1 TPPP21 TPP3 Float, Arm & Stop...
3
© Jobe Valves P.O Box 17 Matamata New Zealand P: +64 (0)7 880 9090 F: +64 (0)7 880 9099 E: [email protected] W: www.jobevalves.com 1 Valve Inlet Pressure Flow Litres/Minute Gallons/Minute Key 25mm & 32mm (1’’ & 1 ¼”) 20mm (¾”) 15mm (½’’) Flow Graph TOPAZ PARTFILL PRODUCT INFO Description Applications Maintaining water levels in: • Rain water harvesting tanks • Water cisterns • Irrigation and process applications. Features • Ideal for use with all makes and models of rain water harvesting tanks • Compact • Constructed from non corroding materials • Built in non return valve • Valve can be locked in off position using the lock off switch • Up to 150mm differential obtainable (dependant on pressure) • Detach TM Valve Seal Access System for quick access to valve seal (Patented) Available Inlet Sizes 15mm (1/2”) 20mm (3/4”) 25mm (1”) 32mm (1 ¼”) All supplied in Detach TM long tail thread with back nut. Topaz Part Fill is a high flow valve intended for use in rain water harvesting tanks. The purpose of the float valve is to automatically maintain a low level of water in the tank during periods of no or low rainfall. This allows services fed by the tank to continue while leaving capacity in the tank for refilling by the next rain. Principle of Operation • The Valve is installed through the side wall of a storage tank. It should be mounted above the overflow level of the tank to prevent backflow. • As the tank empties the weighted float travels down the cord and sits on the bottom stop to activate the valve. • The valve will run until the weighted float lifts clear of the bottom stop. • The float will then rise as rainwater fills the tank and falls as the tank water is used. • The Valve will only function at times when rain fall is insufficient to maintain a water level in the tank above the bottom stop. Pressure Range 0.3 Bar – 10 Bar (5 psi-150 psi) Typical Installaton
Transcript of TOPAZ PARTFILL - Irrigation Direct · 2017. 11. 7. · 3 4 TPPP1 TPPP21 TPP3 Float, Arm & Stop...
-
© Jobe Valves P.O Box 17 Matamata New Zealand P: +64 (0)7 880 9090 F: +64 (0)7 880 9099 E: [email protected] W: www.jobevalves.com 1
Valv
e In
let
Pres
sure
Flow Litres/Minute
Gallons/Minute
Key
25mm & 32mm (1’’ & 1 ¼”)20mm (¾”)15mm (½’’)
Flow Graph
TOPAZ PARTFILL PROducT InFO
Description
ApplicationsMaintaining water levels in:• Rain water harvesting tanks• Water cisterns• Irrigation and process applications.
Features• Ideal for use with all makes and models of rain water harvesting tanks• Compact• Constructed from non corroding materials• Built in non return valve• Valve can be locked in off position using the lock off switch• Up to 150mm differential obtainable (dependant on pressure)• DetachTM Valve Seal Access System for quick access to valve seal (Patented)
Available Inlet Sizes15mm (1/2”)20mm (3/4”)25mm (1”)32mm (1 ¼”)
All supplied in DetachTM long tail thread with back nut.
Topaz Part Fill is a high flow valve intended for use in rain water harvesting tanks. The purpose of the float valve is to automatically maintain a low level of water in the tank during periods of no or low rainfall. This allows services fed by the tank to continue while leaving capacity in the tank for refilling by the next rain.
Principle of Operation• The Valve is installed through the side wall of a storage tank. It should be mounted above the overflow level of the tank to prevent backflow.
• As the tank empties the weighted float travels down the cord and sits on the bottom stop to activate the valve.
• The valve will run until the weighted float lifts clear of the bottom stop.
• The float will then rise as rainwater fills the tank and falls as the tank water is used.
• The Valve will only function at times when rain fall is insufficient to maintain a water level in the tank above the bottom stop.
Pressure Range0.3 Bar – 10 Bar (5 psi-150 psi)
Typical Installaton
-
© Jobe Valves P.O Box 17 Matamata New Zealand P: +64 (0)7 880 9090 F: +64 (0)7 880 9099 E: [email protected] W: www.jobevalves.com2
mm inches
Topaz Dimensions Materials
ABS
Acetal
Acetal
EPDM
Urethane
304 Stainless Steel
Santoprene
Nitrile
HDPE
Polyester
Valve Body
Yellow & White Internal Parts
Filter
Diaphragm
Seal
Springs, Bolts, Nuts, Pin, Screws
Detach Seal
O’Rings
Float
Float Cord
Maximum Temperature of Operation 45ºC, 115ºFNB: High Temperature models on request.
ABCDEFG 15mm (1/2”) Long Tail 20mm (3/4”) Long Tail 25mm (1” ) Long Tail 32mm (1 1/4”) Long TailH
8822790208622010046626735
3 1/28 15/163 17/328 3/162 7/1612/16
3 15/161 13/162 7/162 21/321 3/8
Topaz Dimensions
TOPAZ PARTFILLdImensIOns & mATeRIALs
A
B
C
G
D
E
H
F
-
© Jobe Valves P.O Box 17 Matamata New Zealand P: +64 (0)7 880 9090 F: +64 (0)7 880 9099 E: [email protected] W: www.jobevalves.com 3
TOPAZ PARTFILLdImensIOns & mATeRIALs
21
23
45
6
7
8
9
CODE: TPVP
DESCRIPTION CODE
1
2
3
4
5
6
7
8
9
TPPP2011
TPP2020
TPP2030
TPP2040
TPP2050
TPPP2061
TPP2080
TPP2090
TPP2100
Actuator Cap6g x 10 S/S Screw Frost Pro Plug Frost Pro O’ring Valve Cap Assembly Damping Spring Bearings (set of two) Actuator Arm 6g x 25 S/S Screw
1
2
3
4
TPPP1
TPPP21
TPP3
Float, Arm & Stop Assembly
Cap & Actuator Assembly
Diaphragm Assembly
Detach Base Assembly
DESCRIPTION CODE
2
4
3
1 DESCRIPTION CODE 1
2
3
4
5
Bottom Stop
Weighted Float
Cord
Arm Extension
M5 x 12 Bolt
TPPP010
TPPP020
TPPP1020
TPPP1050
TPP1040
1
23
4
DESCRIPTION CODE 4
56
Detach Base
Detach Filter
Detach Seal
Detach Tail 15mm (½’’) Long
Detach Tail 20mm (¾’’) Long
Detach Tail 25mm (1”) Long
Detach Tail 1” NPT Long
Detach Tail 32mm (1¼”) Long
Detach Tail 1¼” NPT Long
Seal Washer 15mm (½’’)
Seal Washer 20mm (¾’’)
Seal Washer 25mm (1’’)
Seal Washer 32mm (1¼”)
Backing Washer 32mm (1¼”)
Backnut 15mm (½’’)
Backnut 20mm (¾’’)
Backnut 25mm (1’’)
Backnut 32mm (1¼”)
1
2
3
4
5
6
TPP4A010
TPP4A030
TPP4A020
TPP4A0410
TPP4A0420
TPP4A0431
TPP4A0432
TPP4A0441
TPP4A0442
TPP4A050
TPP4A051
TPP4A052
TPP4A053
TPP4A054
TPP4A060
TPP4A061
TPP4A062
TPP4A063
TOPAZ PARTFILLPARTs IdenTIFIcATIOn sheeT
4
3
5
1
2
1
