Bridge Saw Blades Area of influence: North America

Recommended tools

What are the recommended parameters?

Requirements of my machine

Feed Speed

Quality Quality

Tools Technical Datasheets

Dongsin KCBL+KCBL-FLAvailable in 14"-16"-18"

Diameter of the blade (inches) 14 16 18

2400 - 2200 * 1900 - 1500 * 1500 - 1200 *Rotation speed (rpm)

*Follow the recommendations of every manufacturer

*This feed speed is under optimal conditions of work.

White RestThickness of the slab

20 * 40 *Feed speed (inches/min)

10 25Speed at the exit (inches/min)

2-3 2-3Plunge speed (inches/min)

10 * 20 *Speed cutting 45º (inches/min)

Cooling water flowfocused on the cutting area

Sharpen frequentlythe diamond

Use large flange

Well-leveledbed support

Support of largerdimension of the slab

Blade depth 1/8 inch to3/16 inch on the cutting bed

Konig DIAREX UCSAvailable in 14"-16"-18"

Feed Speed

Quality

Italdiamant EVOGRESAvailable in 12"-14"-16"

Feed Speed

Quality

Terminator nanocut DK3Available in 14"-16"-18"

Feed Speed

Tenax DEKTONAvailable in 14" and 16"

Feed Speed

Quality

Diatex DEKCUTAvailable in 14", 16" and 18"

Feed Speed

Quality

Alpha SILENCER IIIAvailable in 12", 14", 16" and 18"

Feed Speed

Quality

REV.01-01/2019

HighQualityMaximum feed speed

Medium Poor

80"/min 40"/min 20"/min

Where can I get these tools?

The diamond grits on the edge of the blade tend to wear down and glaze over when you are cutting hard materials. Sharpening the blade requires making a slurry out of an abrasive material. The following dressing stones are recommended for that purpose:

Italdiamant/ Koing/ AlphaA) By the authorized dealer in your areaB) www.granquarzt.com

TerminatorA) By the authorized dealer in your areaB) www.terminatordia.comC) www.braxton-bragg.com

TenaxA) By the authorized dealer in your areaB) www.braxton-bragg.com

DiatexA) By the authorized dealer in your areaB) http://usa.diatex.eu

C) www.grandquartz.com

DongsinA) By the authorized dealer in your areaB) www.diaflx.com/index.htm

Should I sharpen the blades?

www.Braxton-Bragg.com www.GrandQuartz.com

Sharpen dry Low RPMGet wet the stone

Adhesive Area of influence: North America

What are the recommended parameters?

Requirements of my machine

Where can I get these tools?

Tools Technical Datasheets

Initial waste (inch) 2-430-150Drying time (minimum) **

Apply with a gun anddisposable mouthpiece

The pieces must bepreviously clean and dry

TenaxA) By the authorized dealer in your area

(www.granquarzt.com)

Integra adhesivesA) By the authorized dealer in your area

B) Sales contact: contact@integra-adhesives.com

AkemiA) Web contact:www.braxton-bragg.com B) Web contact: www.granquarzt.com

Slots in the edges toimprove adhesion

HighQualityDrying Time

Medium Poor

30 min 90 min 150 min

Indoors adhesives

Outdoors adhesives

Tenax MASTIDEK(Indoors)

Drying time

Quality

Integra SURFACE BONDER ULTRA(Indoors)

Quality

Drying time

Tenax MASTIDEK(Outdoors)

Feed Speed

Quality

Integra SURFACE BONDER ULTRA(Outdoors)

Quality

Feed Speed

Akemi COLORBOND

Quality

Drying time

Akemi PLATINUM

Quality

Drying time

Akepox 5010

Quality

Drying time

REV.01-01/2019

Area of influence: North America

Recommended Blades

Manual cutter Blades Tools Technical Datasheets

Feed Speed

Quality

Feed Speed

Quality

Feed Speed

Quality

Terminator NANOCUT DKAvailable in 4,5”, 5”, 6” and 7”

Weha R-MESH TURBO BLADEAvailable in 4,5”, 5” and 7”

Pearl P4Available in 4”, 4’5”, 5”,6” ,7”, 10” and 14”

ADW SLIMAvailable in 4,5” and 5”

Feed Speed

Quality

Feed Speed

Quality

Feed Speed

Quality

Feed Speed

Quality

Cyclone MESH THINAvailable in 4”,4,5”,5”,10” and 14”

Apha KATANAAvailable in 4”, 4,5”and 5”

Italdiamant EVOGRESAvailable in 5”

What are the recommended parameters?

Diameter of the blade (inches)

Rotation speed* (rpm)

7”5”4.5”11000-12000 11000-1200011000-12000

*The feed speed should be adjusted according to the type of machine and the thickness of the material. Larger thickness willrequire reduce the feed speed

Requirements of my machine

Water flow focused on the cutting area

Support of largerdimension of the slab

Well-leveledbed support

Sharpen every 4holes drilled

Where can I get these tools?

Alpha/ Cyclone/ PearlA) By the authorized dealer in your area

WehaA) By the authorized dealer in your area

TerminatorA) By the authorized dealer in your areaB) www.Terminatordia.com B) www.grandquartz.com

HighQualityMaximum feed speed

Medium Poor

Fast Medium Slow

Blade depth 1/8 inch to3/16 inch on the cutting bed

REV.01-01/2019

Area of influence: North America

Recommended tools

Drill Bits Tools Technical Datasheets

Feed Speed

Quality

Feed Speed

Quality

Feed Speed

Quality

Feed Speed

Quality

Terminator NANOCUT.DKAvailable in ¼”, 5/16”, 3/8”, ¾”, 1”,

1-1/4”, 1-3/8”, 1-1/2”, 1-3/4”and 2”

Weha WERAMIC CNC BITAvailable in 1”, 1-1/4”, 1-3/8”, 1-1/2”,

2”, 2-1/2” and 3”

ADIAvailable in 3/8”, ¾”, 1”, 1-3/4”, 1-

1/2”, 1-3/4”and 2”

Cyclone Wet Core BitAvailable in either a T-segment

style (1-1 ¾”) or segmented style(2” -5”)

Feed Speed

Quality

Feed Speed

Quality

Feed Speed

Quality

Feed Speed

Quality

ADWAvailable in 5/16”, 25/64”, 5/8”,

25/32”, 3/16”and 5/32”

AppexAvailable in 1/4", 3/8", 1/2",

5/8", 3/4", 7/8", 1", 1-1/8", 1-1/4", 1-3/8", 1-1/2", 1-5/8", 1-3/4", 1-7/8", 2", 2-1/4", 2-

1/2", 2-3/4", 3", 3-1/2", and 4

ProSeriesAvailable in 3/8”, ¾”, 1”, 1-3/4”, 1-

1/2”, 1-3/4”and 2”

Diamut DEKTONAvailable in 1-3/8”

What are the recommended parameters?

Rotation Speed (rpm) 4500*

*This rotation speed will depend on the manufacturer and the diameter of the toolThe working parameters should be recommended mainly by the tools manufacturer.

Requirements of my machine

Sharpen every 4holes drilled

Water flow focused on the cutting area

Support of largerdimension of the slab

Well-leveledbed support

Where can I get these tools?

ADWA) By the authorized dealer in your area

TerminatorA) By the authorized dealer in your areaB) www.diaflx.com/index.htm

HighQualityMaximum feed speed

Medium Poor

Fast Medium Slow

REV.01-01/2019

HighQualityMaximum feed speed

Medium Poor

10 inch/min 8 inch/min 6 inch/min

Finger bits Area of influence: North America

Recommended bits

What are the recommended parameters?

Requirements of my machine

Where can I get these tools?

Tools Technical Datasheets

Italdiamant / ADIA) At www.grandquartz.com

B) By the authorized dealer in your area

TerminatorA) By the authorized dealer in your area

B) www.terminatordia.com

DongsinA) By the authorized dealer in your area

Terminator NANOCUT DKAvailable in 8"x12", 8"x16" and 8"x20"

Dongsin M1Available in one size

ADI Seg FOR DEKTONAvailable in one size

Quality

Feed Speed

Quality

Feed Speed

Quality

Feed SpeedFeed Speed

Quality Quality

Feed Speed

Italdiaman EVOGRESAvailable in one size

Thickness of the slab 8mm 12mm 20mm

4500 4500 4500Rotation speed (rpm)6000 - 7500* 6000 - 7500* 6000 - 7500*Rotation speed

milling tool (rpm)

8 mm 12 mm 20 mmThickness of the slab

8 7,5 7Feed speed (inches/min)3 3 3Speed at exit (inches/min)

Cooling water flowfocused on thecutting area

Well-leveled bed support

Sharpen the toolbefore each real job

Support of largerdimension of the slab

Diamut DEKTON BITAvailable in one size

*Follow the recommendations of every manufacturer

REV.01-03/2019