To: VLBA Data Acquisition Group From: Alan E.E. Rogers A...

13
VLBA ACQUISITION MEMO #169 MASSACHUSETTS INSTITUTE OF TECHNOLOGY HAYSTACK OBSERVATORY WESTFORD, MASSACHUSETTS 01886 14 September 1989 Area Code 508 692-4764 To: VLBA Data Acquisition Group From: Alan E.E. Rogers Subject: Optimization of equalizer for playback of D1 tapes at 56 Kb/in A] Equalizer circuit An equalizer has been built and tested for playback of D1 tape at 160 IPS and S Mb/s per track (56K flax transitions/in). Figure 1 shows the equalizer circuit and Figure 2 shows the resulting "eye" pattern. B] Equalizer phase and delay response The amplitude and delay response is shown in Figure 3. Two sets of curves are shown giving the response with and without the 470 pf capacitor which provides low pass filtering of the high frequencies above the bandedge. In the new parallel playback electronics this low pass will probably be performed with a separate circuit. C] SNR The spectral signal to noise ratio (which is independent of the equalizer) is shown in Figure 2. The broadband signal to noise ratio is about 18 dB. The broadband SNR is dependent on the equalizer and is optimized by having an equalizer which weights the spectral SNR in proportion to the SNR - at least when the noise is only the random (thermal) portion. The bit error rate (BER) is dependent on a modified SNR which includes the intersymbol interference, due to imperfect waveform equalization, as a reduction of the available signal which competes with the noise in the decision process. D] Optimization by manual adjustment The equalizer was first optimized by substituting potentiometers for some of the resistors and a variable capacitor for the series resonant adjustment of C1,L. To the first order Cl adjusts the peak frequency to bandedge R1 adjusts the Q of the resonance R2,C3 adjusts the mid frequency response R3 adjusts the phasing between bandedge and midband R4 adjusts the low frequency cut-off Ideally the BER should be optimized but in practice it is convenient to watch a spectrum analyzer and "eye" pattern display.

Transcript of To: VLBA Data Acquisition Group From: Alan E.E. Rogers A...

  • VLBA ACQUISITION MEMO #169M ASSA CHU SETTS IN STITU TE O F TEC H N O L O G Y

    HAYSTACK OBSERVATORYWESTFORD, MASSACHUSETTS 01886

    14 September 1989 Area Code 508 692-4764

    To: V L B A D ata Acquisition G ro upFrom : A lan E.E. Rogers

    Subject: O p tim iza tion of equalizer for playback of D1 tapes at 56 K b /in

    A] E qua lize r circuitA n equal izer has been built and tes ted for playback of D1 tape at 160 IPS and S M b /s per

    track (56K flax transi t ions / in ) . Figure 1 shows the equalizer circuit and Figure 2 shows the resulting "eye" pa tte rn .

    B] E q ua lize r phase and delay responseT h e am plitude and delay response is shown in Figure 3. Two sets o f curves a re shown

    giving the resp o nse with and w ithout the 470 p f capacitor which provides low pass filtering of the high frequencies above the bandedge. In the new parallel playback electronics this low pass will p robably be p e rfo rm ed with a sep a ra te circuit.C] S N R

    T h e spectral signal to noise ratio (which is independent o f the equalizer) is shown in Figure 2. T h e b ro a d b a n d signal to noise ra tio is abou t 18 dB. T he b roadband SN R is d epen d en t on the equalizer and is optim ized by having an equalizer which weights the spectral S N R in p ro p o rt ion to the S N R - at least w hen the noise is only the random (therm al) portion. T he bit e r ro r ra te (B E R ) is d e p e n d e n t on a m odified S N R which includes the intersymbol in terference, due to im perfect waveform equalization, as a reduction o f the available signal which com petes with the noise in the decision process.

    D] O p tim iza tion by m anual ad justm entT h e equalizer was first optim ized by substituting po ten tiom ete rs for som e of the resistors

    and a variable capac ito r for the series resonan t ad justm ent of C1,L. To the first o rderC l adjusts the peak frequency to bandedgeR1 adjusts the Q of the resonanceR2,C3 adjusts the mid frequency responseR3 adjusts the phasing between bandedge and m idbandR4 adjusts the low frequency cut-off

    Ideally the B E R should be optim ized but in practice it is convenient to watch a spectrum analyzer and "eye" p a tte rn display.

  • E] C heck ing optim ization by circuit simulationA co m ple te circuit sim ulation provides som e useful added insight into the optimization. The

    following m odel was ad op ted1] G e n e ra te p seudo random square wave with 8 M H z sam ple rate2] F F T to frequency dom ain3] F ilter signal with

    a) C u rre n t source into parallel L = 23 /iH, C = 8pf to sim ulate inductive pick-up ofhead and its resonance.b) G ap loss o f 0.35 microns (see Acquisition M em o #150).c) Spacing o f 0.35 microns.

    4] A d d noise filtered with head resonant circuit5] E qualize signal plus noise6] F F T to t im e dom ain7] D evelop an "eve" pa tte rn8] M e asu re signal from the opening of eye9] R ep ea t with signal tu rned off to m easu re noise level and hence the SN R

    Figure 4 shows som e examples of the input signal, reconstructed waveform and "eve" p a t te rn s from the co m p u te r simulation. N oted are cases w here the eye pa tte rn is d ecrad ed bv low frequency baseline w an d er and high frequency noise p resen t without low pass filter.

    F igure 5 gives the m odified SN R from which the B ER can be calculated as a function of various p a ram e te rs .F] T h e n eed for "DC restoration"

    T h e n eed for "DC restora tion ' was described in a Haystack m em o of 8 June 1988 (attached). A circuit for the D C res to ra t ion was tested and found to substantially improve the M KIIIA p e rfo rm an c e (by a factor o f 10-100 in PER ). However, owing to its complexity, the circuit has not yet been re tro f i t ted into M KIIIA. An a l te rna te and som ewhat simpler circuit by W.D. H uber has b een found (by D an Sm ythe) in the IE E E Transactions on Magnetics, M A G - 17, N o .6, p^. 3352, 1981) and D C re s to ra t ion is p lanned for the V LBA parallel reproduce electronics. T h e com puter s im ula tion confirm s the advantage of DC resto ra tion even for a random signal without lonti runs o f zeroes.G] T h e need for a low pass filter

    T h e high frequency noise (especially around head resonance) has to be m ore adequately filtered than it is in the p resen t MKIILA electronics. Adding one additional high frequency poie (with the 470 p f in th e equalizer) may be adequ a te for the acquisition recorders - but even better p e rfo rm a n ce can be achieved with an even be tte r filter.H] E qua lize r dispersion

    Ideally the equalizer should be non-dispersive. T he delay characteristic has som e ripple and increases rapidly below 70 KHz. T he co m pu te r simulation shows that there are two p rob lem s with not allowing the in teg ra to r to go sufficiently low in frequency:

    1] T h e re is baseline wander.2] D ispers ion increases the intersymbol in terference and degrades the eye pattern .

    In o rd e r to optim ize pe rfo rm ance with D C resto ra tion to reduce the effect of low frequencv noise, it is advan tageous to first extend the in tegra tor to the lowest possible frequencv to reduce dispersion. T his can be accom plished by increasing C3 (and decreasing R3 to preserve the C3 R3 t im e cons tan t) as m uch as possible while still m ain ta in ing acceptable loss in the equalizer.

  • NDTl S:

    47,000 pF 5600

    l h v p a s s

    1] Cl ADJUSTS PESnr-JAi t d b a n nrnor; d F -l̂ SHNANCl2] Rl ADJUSTS Q DF

    3] R3 ADJUSTS PHASE4] R2 ADJUSTS LL'VE!. ,UF MIDBAND5] R4 ADJUSTS LCIV/ FRFQ. CUTOFF CIF INTEGRATEIR6] SCALING DOWN R3 AND SCALING UP C3

    IMPROVES INTEGRATOR AT THE EXPENCE □F INCREASED EQUALIZER LEISS

    5600

    R4

    i u ! b u i i \FILECQCIR.DV/G

  • 1i.w s\.:

    * / . -

    h 3 C l 1 5 U?«

    e'

    f *‘

    K

    •* .

    Ps P

    & , A .

    • ' ^ : F

    A li ii

    * J" A * - / »

    it-. i f c . i f e -j • i : ^ r j r r n ^ ?W ' * % « * *

    A / , A A A A;j f i> a~~.f ’t—Jt 3 --*- 1p . , * . V - v . r V V !

    1£*

    '

    i-

    ; • V r L ■ £. lOOn;L • ,

    \

    i> 1 /6c XPS IS. Se?T 27

    j / V / f £>2 /-6v IPS >2 m'e/TS'I

  • FIG 3 EQUALIZER AMPLITUDE AND DELAY RESPONSE WITH AND VITHDUT

    LDVPASS

  • l x in

    EQUALIZATION WITH NO PHASE ERROR

    WITH R 4 = 1 0 0 0 OHMS - SHOWING DEGRADATION OF EYE PATTERN BY "DC BASELINE WANDER" (SEE TEXT FOR USE OF "DC RESTORATIO N")

    FIG 4ry SOME SAMPLE "EYE" PATTERNS r \ O M COMPUTER SIMULATION

  • RELA

    TIV

    E

    SNR

    dB

    12 -

    10 -

    8

    .................. .....

    ....................1 ......................

    4’""

    J ...........

    2 '

    .4 " ' ' 53

    1--------------- T

    FIG 5 OPTIMIZATION

    CURVE #1: - PHASING R3 FROM 9 TD 191 DHMS

    CURVE tt2: - LOW FREQ. CUTOFF R4 FRDM 560 TD 11760 OHMS

    CURVE #3; - SPACING LDSS SPACING FRDM 0.035 TD 0.74 MICRONS

    CURVE tt4! - L D W PA S S LDWPASS CAP FRDM 50 TO 1050 PF

    CURVE #5: - EXTENDING INTEGRATOR C3 FRDM 100 PF TD 2100 PF R3 FRDM 910 DHMS TO 43 DHMS LDWPASS CAP FRDM 47 PF TD 990 PF

    NOTE* RIPPLE ON CURVES 1 AND 4 IS DUE TD NUMERICAL APPROXIMATIONS IN PROGRAM

    FILE'BER.DVG

    CURVES

  • M ASSA CHU SETTS IN STITU TE O F TEC H N O L O G Y HAYSTACK OBSERVATORY

    WESTFORD, MASSACHUSETTS 01886 8 June 1988 Area Code 508

    692-4764

    To:From :

    V LB I G ro upA lan E.E. Rogers H a n s F. H in teregger

    Subject: N arrow T rack S N R M argin Equalization Im provem ents and the U se ofD.C. R esto ra tion

    In troduct ionW e a re studying the p resen t M K IIA system in the hope that a few m inor changes might lead to a substan tia l im provem ent in the margin over which the system will opera te . So far we have found two a rea s which might yield som e im provm ent as follows:

    a) L im iting the analog response to 4 M H z (at 135 IPS playback) so that the noise from the h ead resonance at 12 M H z and high frequency noise pick-up d oesn ’t d eg rad e the b ro ad b an d SNR.b) D ynam ic ad justm en t of the co m para to r threshold to reduce the erro rs p roduced by the inability o f equalized signal to follow low frequency components.

    P resen t E qua lize r L im itationsT h e p re se n t equalizer whose transfer function is shown in Figure 1 has the low frequency rolloff o f the equal izer set a t abou t 40 K H z and as a result low frequency signals a re poorly rep ro d u c ed as illustrated by the "D.C." shifts shown in Figure 2. This prob lem is especially bad during the t im e code and auxilliary da ta portions of the fram e and results in C R C errors. We rec o m m e n d tha t m o re ones be encoded into the auxilliary data field when tapes a re recorded. H ow ever the p rob lem is not limited to the auxilliary data and additional m easu res a re probably needed . Simply reducing the low frequency roll-off actually degrades the b ro ad b and S N R as the spectra l S N R (shown in F igure 6) is degrad ing by 6 d B /oc tav e at low frequencies.D.C. R es to ra tionT he effect o f the D.C. shifts can be greatly reduced by adding positive and negative p eak level de tec to rs and using the ir m ean to s tee r the re ference on the com parator . F igure 3 shows both the equalized signal and the voltage mid-way between the positive and negative peaks.Im proved E qualizer

    With a D.C . re s to ra t ion circuit the low frequency response can actually be ex tended since the c o m p a ra to r re fe ren ce now tracks low frequency com ponents. In addition an additional high frequency cut-off has been added as illustrated in Figure 5.

  • C om p ariso n T estsT h e im proved equalizer with D.C. res to ra tion circuit was tested on the W estford acquisition re c o rd e r using a tap e record ed at H a t C reek during the 3 m m experim ent (which reproduced poorly on the processor) . T h e results a re shown in Figure 6.T h e im proved equal izer a lone gives about a factor o f two im provem ent in e r ro r ra te while the com bina tion of b e t te r equalizer plus D.C. resto ra tion gives about 10-100 fold im provem ent in e r ro r rate.C onclusionsU n fo r tu n a te ly the circuit changes needed to im plem ent D.C. restora tion a re fairly extensive. T h e next step is to test the p ro to type on the processor and if the im provem ent is d ram atic look for s im pler ways o f achieving the sam e result. This study indicates tha t the p resen t m argin (to 0 .1% e r ro r ra te ) on the H a t C reek tapes is about 3 dB and increases to about 5 dB with im proved equaliza tion and D.C. restoration.

    A t ta ch m e n ts (5 F igures)

  • e.os-

    - b b b a b b a a b b a a b b a a ba

    bbbbbb b a11-_ pAc;>f̂Sŷ > *

  • Ŝ>0rr, f J~c

    c*/yso,r;„V

    >70 /

    etcX o

    /-, -tyi J t~G^n C-iy <7 '

    ^ +**gr jo > < /• • i^: / 3£r * J V ^ t r .

    s .j ^ y e J ,y ^ ( V£ k f

    /* s /& re & . f. Gyr>y> osi a ^ /~ C ospba fGŝ oi

    ■CxSe/r/

    h ju L£ 3 .

  • /2_ '3 /y- /S' 14,

    tT/i//^ c/g

    h j „ ,e I f . /V fi j ,

    < • 4 < / a L ^ T / o _ / c o

    °̂ ~f* C*nr' Cr>y> s'C*St>ryypr, /

    - ^ ’ CA?C- t f j p s f , ___

    ^ w O ;^ " e V " ^ /°~ ,o o ) w U f ■ y /r ^ y ^ ^ r . ^ Z ,/ ^ " X -e -L/* e e ;« ‘ ''*/*■•£- M * C y , „ y y , „ x . z _ 3 J

    * -30

    4

    N-£

    S', . \T/V^ t/j* hf̂uMsic

    - L . - M H 7 -____5^o_JcVjr 3 »

    \ ___ / p o A "/y z_ -2.C? o ^ fr - 2 o - \ S o k /jz . /J T ^

    \ • 2 * k H z ?

  • 12.00

    --J |-----tf>T5>-------- WV^-'

    6x

    H-Voo dII

    ((/~ /pj /s

    | A M S ^ c,,I 7>-r- >