TMT, TMTU, TMTW, TMT FL and TMTW FL Technical … · 18 520L0523 • Rev CB • Mar 2010 TMT, TMTU,...
17
18 520L0523 • Rev CB • Mar 2010 TMT, TMTU, TMTW, TMT FL and TMTW FL Technical Information Shaft Versions Shaft Versions, European Versions A: Cylindrical shaft Ø 40 mm F: Parallel key A12 x 8 x 70 DIN 6885 B: Involute splined shaft ANS B92.1 - 1970 standard Flat root side fit Pitch 12/24 Teeth 17 Major diam. 1.50 inch Pressure angle 30˚ C: Tapered shaft Ø 45 mm (ISO/R775) E: DIN 937 Across flats: 46 mm Tightening torque: 500 ± 30 N•m [4425 ± 265 lbf•in] D: Taper 1 : 10 G: Parallel key B12 x 8 x 28
Transcript of TMT, TMTU, TMTW, TMT FL and TMTW FL Technical … · 18 520L0523 • Rev CB • Mar 2010 TMT, TMTU,...
18 520L0523 • Rev CB • Mar 2010
TMT, TMTU, TMTW, TMT FL and TMTW FL Technical Information
Shaft Versions
Shaft Versions, European Versions
A: Cylindrical shaft Ø 40 mmF: Parallel key A12 x 8 x 70 DIN 6885
B: Involute splined shaft ANS B92.1 - 1970 standard Flat root side fit Pitch 12/24 Teeth 17 Major diam. 1.50 inch Pressure angle 30˚
C: Tapered shaft Ø 45 mm (ISO/R775)E: DIN 937 Across flats: 46 mm Tightening torque: 500 ± 30 N•m [4425 ± 265 lbf•in]D: Taper 1 : 10G: Parallel key B12 x 8 x 28
19520L0523 • Rev CB • Mar 2010
TMT, TMTU, TMTW, TMT FL and TMTW FL Technical Information
Shaft Versions
Shaft Versions, US Versions
D: Cylindrical shaft Ø 1 1/2 inchI: Parallel key 3/8 x 3/8 x 2 1/4 inch B.S. 46
E: Involute splined shaft ANS B92.1 - 1970 standard Flat root side fit Pitch 12/24 Teeth 17 Major diam. 1.50 inch Pressure angle 30˚
F: Tapered shaft 1 3/4 inG: Cone 1 : 8 SAE J501H: 1 1/4 - 18 UNEF across flats: 2 3/16 inch Tightening torque: 4425 ± 265 lbf.in [500 ± 30 N•m]J: Parallel key 7/16 x 7/16 x 1 1/4 inch B.S. 46
20 520L0523 • Rev CB • Mar 2010
TMT, TMTU, TMTW, TMT FL and TMTW FL Technical Information Technical Data
Port Thread Versions
A: G Main portF: ISO 228/1 – G ¾
C: G Drain/release portH: ISO 228/1 – G 1/4
B: UNF Main portP: 1 1/16 – 12 UN
D: UNF Drain portI: 9/16 – 18 UNF O-ring boss port
E: UNF Release portJ: 7/16 – 20 UNF O-ring boss port
21520L0523 • Rev CB • Mar 2010
TMT, TMTU, TMTW, TMT FL and TMTW FL Technical Information Dimensions – Attached Component
Dimensions of the Attached Component for TMT U (bearing less)
Internal spline data for the component to be attachedThe attached component must have internal splines corresponding to the external splines on the motor cardan shaft, please see drawings.Material:Case hardening steel with a tensile strenght corresponding at least to 20 MoCr4 (90 daN/mm2). See also SAE 8620 for further information on steel material.
Hardening specification:• on the surface: HV = 750 ± 50• 0.7± 0.2 mm under the surface: HV = 560
Standard ANS B92.1 - 1970, class 5 (corrected m . x = 1; m = 2.1166
Flat root side fit mm inchNumber of teeth z 16 16Pitch DP 12/24 12/24Pressure angle 30˚ 30˚Pitch dia. D 33.8656 1.3333
Major dia. Dri 38.4 +0.4
1.5118 +0.0157
0 0Form dia. (min) Dfi 37.6 1.4803
Minor dia. Di 32.15 +0.04
1.2657 +0.00157
0 0Space width (circular)Lo 4.516 ± 0.037 0.1777 ± 0.0014Tooth thicknes
So 2.170 0.0854
(circulator)Fillet radius Rmin. 0.5 0.02Max. measurement
I 26.9+0.1
1.059+0.004
between pins* 0 0Pin dia. d 4.843 ± 0.001 0.1903 ± 0.00004
*Finished dimensions (when hardened)
A: Hardened stop plateB: Oil circulation holeC: O-ring 125 x 2 mm [ 0.08 in]D: Drain connection
22 520L0523 • Rev CB • Mar 2010
TMT, TMTU, TMTW, TMT FL and TMTW FL Technical Information Dimensions
Drain Connection on TMTU or Attached Component
A drain line should always be used.
The drain line can be connected at two different points:• at the motor drain connection• at the drain connection of the attached component
If a drain is fitted to the attached component, it must be possible for oil to flow freely between motor and the attached component.
The drain line must be led to the tank in such a way that there is no risk of the motor and the attached component being drained of oil when at rest.
The maximum pressure in the drain line is limited by the attached component and its shaft seal.
A blank shaft is available for TMTU motor, please contact Sauer-Danfoss Sales Organisation.
After machining the blank shaft must be hardened according to Sauer-Danfoss specification on page 21.
Blank shaft
23520L0523 • Rev CB • Mar 2010
TMT, TMTU, TMTW, TMT FL and TMTW FL Technical Information
Dimensions
Dimensions, European Version
4-Bolt flange-spigot diameter ∅160 mm - BC ∅200 mm
Type
L mm
L1 mm
L2
mm (in) (in) (in)
TMT 250 191.5 165 150.5
[7.54] [6.50] [5.93]
TMT 315 200.8 174.3 158.9
[7.91] [6.86] [6.26]
TMT400 211.3 184.8 170.3
[8.32] [7.28] [6.70]
TMT 470 219.5 193 178.5
[8.64] [7.60] [7.03]
TMT 500 211.3 184.8 170.3
[8.32] [7.28] [6.70]
TMT 630 225.3 198,8 184.3
[8.87] [7.83] [7.26]
C: G 3/4 ; 17 mm [0.67 in] deepD: Drain connection G 1/4 ; 12 mm [0.47 in] deep
24 520L0523 • Rev CB • Mar 2010
TMT, TMTU, TMTW, TMT FL and TMTW FL Technical Information
Dimensions
Dimensions, European Version
4-Bolt flange-spigot diameter ∅125 mm - BC ∅160 mm
Type
L mm
L1 mm
L2
mm (in) (in) (in)
TMT 250 200 173.5 159
[7.87] [6.83] [6.26]
TMT 315 209.3 182.8 168.3
[8.24] [7.20] [6.63]
TMT400 219.8 193.3 178.8
[8.65] [7.61] [7.04]
TMT 470 228 201.5 187
[8.98] [7.93] [7.36]
TMT 500 219.8 193.3 178.8
[8.65] [7.61] [7.04]
TMT 630 233.8 207.3 192.8
[9.20] [8.16] [7.59]
C: G 3/4 ; 17 mm [0.67] deepD: Drain connection G 1/4 ; 12 mm [0.47 in] deep
25520L0523 • Rev CB • Mar 2010
TMT, TMTU, TMTW, TMT FL and TMTW FL Technical Information
Dimensions
Dimensions, US Version
Type
L mm
L1 mm
L2
mm (in) (in) (in)
TMT 250 218.7 192.4 177.9
[8.61] [7.57] [7.00]
TMT 315 227.9 201.7 187.2
[8.97] [7.94] [7.37]
TMT400 238.4 212.2 197.7
[9.39] [8.35] [7.78]
TMT 470 246.7 220.4 205.9
[9.71] [8.68] [8.11]
TMT 500 238.4 212.2 197.7
[9.39] [8.35] [7.78]
TMT 630 252.4 226.2 211.7
[9.94] [8.91] [8.33]
C: 1 1/16 - 12 UN O-ring boss port; 19 mm [0.75 in] deepD: Drain connection 9/16 - 18 UNF O-ring boss port; 12.7 mm [0.5 in] deep
4-Bolt flange-spigot diameter ∅5 in, SAE C mounting flange - BC ∅6.37 in
26 520L0523 • Rev CB • Mar 2010
TMT, TMTU, TMTW, TMT FL and TMTW FL Technical Information
Dimensions
Dimensions, European Version
Bearing less
Type
L mm
L1 mm
L2
mm (in) (in) (in)
TMTU 250 158.5 131 117.5
[6.24] [5.16] [4.63]
TMTU 315 168.8 141.3 126.8
[6.65] [5.56] [4.99]
TMTU 400 178.3 151.8 137.3
[7.02] [5.98] [5.41]
TMTU 470 186.5 160 145.5
[7.32] [6.26] [5.73]
TMTU 500 178.3 151.8 137.3
[7.02] [5.98] [5.41]
TMTU 630 192.3 165.8 151.3
[7.57] [6.53] [5.96]
C: G 3/4 ; 17 mm [0.67 in] deepD: Drain connection G 1/4 ; 12 mm [0.47 in] deep
27520L0523 • Rev CB • Mar 2010
TMT, TMTU, TMTW, TMT FL and TMTW FL Technical Information
Dimensions
Dimensions, US Version
Bearing less
C: 1 1/16 - 12 UN O-ring boss port; 19 mm [0.75 in] deepD: Drain connection 9/16 - 18 UNF O-ring boss port; 12.7 mm [0.5 in] deep
Type
L mm
L1 mm
L2
mm (in) (in) (in)
TMTU 250 158.5 131 117.5
[6.24] [5.16] [4.63]
TMTU 315 168.8 141.3 126.8
[6.65] [5.56] [4.99]
TMTU 400 178.3 151.8 137.3
[7.02] [5.98] [5.41]
TMTU 470 186.5 160 145.5
[7.32] [6.26] [5.73]
TMTU 500 178.3 151.8 137.3
[7.02] [5.98] [5.41]
TMTU 630 192.3 165.8 151.3
[7.57] [6.53] [5.96]
28 520L0523 • Rev CB • Mar 2010
TMT, TMTU, TMTW, TMT FL and TMTW FL Technical Information
Dimensions
Dimensions, European Version
Type
L mm
L1 mm
L2
mm (in) (in) (in)
TMT 250 FL 240.1 213.6 199.1
[9.45] [8.41] [7.84]
TMT 315 FL 249.4 222.9 208.4
[9.82] [8.78] [8.20]
TMT 400 FL 259.9 233.4 218.9
[10.23] [9.19] [8.62]
TMT 470 FL 268.2 241.7 227.2
[10.56] [9.52] [8.94]
TMT 500 FL 259.9 233.4 218.9
[10.23] [9.19] [8.62]
TMT 630 FL 273.9 247.4 232.9
[10.78] [9.74] [9.17]
4-Bolt flange-spigot diameter ∅125 mm - BC ∅160 mm
C: G 3/4 ;17 mm [0.67 in] deepD: Drain connection G 1/4 ; 12 mm [0.47 in] deepE: Release port G 1/4 ; 12 mm [0.47 in] deep
29520L0523 • Rev CB • Mar 2010
TMT, TMTU, TMTW, TMT FL and TMTW FL Technical Information
Dimensions
Dimensions, US Version
4-Bolt flange-spigot diameter ∅5 in, SAE C mounting flange - BC ∅6.37 in
Type
L mm
L1 mm
L2
mm (in) (in) (in)
TMT 250 FL 259 232.5 218
[10.20] [9.15] [8.58]
TMT 315 FL 268.3 241.8 227.3
[10.56] [9.52] [8.95]
TMT 400 FL 278.8 252.3 237.8
[10.98] [9.93] [9.36]
TMT 470 FL 287 260.5 246
[11.30] [10.26] [9.69]
TMT 500 FL 278.8 252.3 237.8
[10.98] [9.93] [9.36]
TMT 630 FL 292.8 266.3 251.8
[11.53] [10.48] [9.91]
C: 1 1/16 - 12 UN O-ring boss port; 19 mm [0.75 in] deepD: Drain connection 9/16 - 18 UNF O-ring boss port; 12.7 mm [0.5 in] deepE: Release port 7/16 - 20 UNF O-ring boss port; 12.7 mm [0.5 in] deep
30 520L0523 • Rev CB • Mar 2010
TMT, TMTU, TMTW, TMT FL and TMTW FL Technical Information
Dimensions
Dimensions, US Version
4-Bolt flange-spigot diameter ∅7.08 in - BC ∅8.82 in
C: 1 1/16 - 12 UN O-ring boss port; 19 mm [0.75 in] deepD: Drain connection 9/16 - 18 UNF O-ring boss port; 12.7 mm [0.5 in] deepE: Release port 7/16 - 20 UNF O-ring boss port; 12.7 mm [0.5 in] deep
Type
L mm
L1 mm
L2
mm (in) (in) (in)
TMT 250 FL 232 205.5 191
[9.13] [8.09] [7.52]
TMT 315 FL 241.2 214.7 200.2
[9.50] [8.45] [7.88]
TMT 400 FL 251.7 225.2 210.7
[9.91] [8.87] [8.30]
TMT470 FL 260 233.5 219
[10.24] [9.19] [8.62]
TMT 500 FL 251.7 225.2 210.7
[9.91] [8.87] [8.30]
TMT 630 FL 265.7 239.2 224.7
[10.46] [9.42] [8.85]
31520L0523 • Rev CB • Mar 2010
TMT, TMTU, TMTW, TMT FL and TMTW FL Technical Information
Dimensions
Dimensions, European Version
4-Bolt flange-spigot diameter ∅180 mm - BC ∅224 mm
C: G 3/4 ; 17 mm [0.67 in] deepD: Drain connection G 1/4 ; 12 mm [0.47 in] deepE: Release port G 1/4 ; 12 mm [0.47 in] deep
Type
L mm
L1 mm
L2
mm (in) (in) (in)
TMT 250 FL 232 205.5 191
[9.13] [8.09] [7.52]
TMT 315 FL 241.2 214.7 200.2
[9.50] [8.45] [7.88]
TMT 400 FL 251.7 225.2 210.7
[9.91] [8.87] [8.30]
TMT470 FL 260 233.5 219
[10.24] [9.19] [8.62]
TMT 500 FL 251.7 225.2 210.7
[9.91] [8.87] [8.30]
TMT 630 FL 265.7 239.2 224.7
[10.46] [9.42] [8.85]
32 520L0523 • Rev CB • Mar 2010
TMT, TMTU, TMTW, TMT FL and TMTW FL Technical Information
Dimensions
Dimensions, European Version
Wheel - Spigot diameter ∅180 mm - BC ∅210 mm
Type
L1
mm L2
mm (in) (in)
TMT W 250 250.1 99
[9.85] [3.90]
TMTW 315 259.4 108.3
[10.21] [4.26]
TMTW 400 269.9 118.8
[10.63] [4.68]
TMTW 470 278.1 127
[10.95] [5.00]
TMTW 500 269.9 118.8
[10.63] [4.68]
TMTW 630 283.9 132.8
[11.18] [5.23]
C: G 3/4 ; 17 mm [0.67 in] deepD: Drain connection G 1/4 ; 12 mm [0.47 in] deepE: Ø 14.1F: 5 x M14 • 1.5 H: M10, 17 mm [0.67 in] deep
-------not painted
33520L0523 • Rev CB • Mar 2010
TMT, TMTU, TMTW, TMT FL and TMTW FL Technical Information
C: 1 1/16 - 12 UN O-ring boss port; 19 mm [0.75 in] deepD: Drain connection 9/16 - 18 UNF O-ring boss port; 12.7 mm [0.5 in] deepE: Ø 14.1F: 5 x M14 • 1.5
----not painted
Dimensions
Dimensions, US Version
Wheel - Spigot diameter ∅180 mm - BC ∅210 mm
Type
L1
mm L2
mm (in) (in)
TMT W 250 250.1 99
[9.85] [3.90]
TMTW 315 259.4 108.3
[10.21] [4.26]
TMTW 400 269.9 118.8
[10.63] [4.68]
TMTW 470 278.1 127
[10.95] [5.00]
TMTW 500 269.9 118.8
[10.63] [4.68]
TMTW 630 283.9 132.8
[11.18] [5.23]
34 520L0523 • Rev CB • Mar 2010
TMT, TMTU, TMTW, TMT FL and TMTW FL Technical Information
C: 1 1/16 - 12 UN O-ring boss port; 19 mm [0.75 in] deepD: Drain connection 9/16 - 18 UNF O-ring boss port; 12.7 mm [0.5 in] deepE: Release port; 7/16 - 20 UNF, 13 mm [0.51 in] deep
Dimensions
Dimensions, US Version
Wheel - Spigot diameter ∅160 mm - BC ∅194 mm
Type
L mm
L1 mm
L2
mm L3
mm (in) (in) (in) (in)
TMTW 250 FL 131.0 86.8 101.3 110.8
[5.16] [3.42] [3.99] [4.36]
TMTW 315 FL 140.2 96.0 110.5 120.0
[5.52] [3.78] [4.35] [4.72]
TMTW 400 FL 150.7 106.5 121.0 130.5
[5.93] [4.19] [4.76] [5.14]
TMTW 500 FL 150.7 106.5 121.0 130.5
[5.93] [4.19] [4.76] [5.14]
TMTW 630 FL 164.7 120.5 135.0 144.5
[6.48] [4.74] [5.31] [5.69]
