TITAN SCBA Pressurization Instructions · PRESSURIZATION INSTRUCTIONS Insert the regulator into the...
1
PRESSURIZATION INSTRUCTIONS Insert the regulator into the Air Klic on the facepiece such that the HUD display is positioned on top, and press firmly until you hear both release buttons snap into place. A CLICK will be heard when each Air Klic button is properly engaged Take a sharp, deep breath to activate the regulator, or press the manual override button on the front of the regulator. Then, take several breaths to check the flow of air. TITAN ™ SCBA Check the Heads-Up Display (HUD) to ensure that the display reads full cylinder pressure (all four green LEDs lit). Remove the second stage regulator from the facepiece by pressing the two release buttons simultaneously. 10 Ensure that the needle on the chest mounted pressure gauge reads in the green (FULL) zone. To remove the second stage from the facepiece first take a deep breath and then press the top of the man- ual override button on the second stage regulator. This stops the flow of air. 9 Verify that the red bypass knob is in the closed position. Fully open the cylinder valve. Quickly open and close the bypass valve to ensure that it is operating properly. Fully depress the shutoff button on the second stage regulator. Remove the second stage regulator from either the waist strap-mounted or shoulder strap-mounted regulator holder by pressing the two release buttons simultaneously. Place the second stage back into either the waist strap-mounted or shoulder strapmounted regulator holder. 11 8 1 2 3 4 5 6 7A 7B Honeywell Industrial Safety 900 Douglas Pike Smithfield, RI 02917 USA US: 800.430.5490 Canada: 888.212.7233 www.honeywellsafety.com HSPRSP.226 Printed in U.S.A. © 2016 Honeywell International Inc. WARNING! Failure to inspect and correctly maintain your SCBA and/or to replace any damaged components can result in the unit not operating correctly and will expose the user to serious illness, injury or death. Carefully follow all of the cleaning and maintenance procedures outlined in the Honeywell TITAN SCBA Operating and Maintenance Instruction Manual.
Transcript of TITAN SCBA Pressurization Instructions · PRESSURIZATION INSTRUCTIONS Insert the regulator into the...
PRESSURIZATION INSTRUCTIONS
Insert the regulator into the Air Klic on the facepiece such that the HUD display is positioned on top, and press firmly until you hear both release buttons snap into place. A CLICK will be heard wheneach Air Klic button is properly engaged
Take a sharp, deep breath to activate the regulator, or press the manual override button on the front of the regulator. Then, take several breaths to check the flow of air.
TITAN™ SCBA
Check the Heads-Up Display (HUD) to ensure that the display reads full cylinder pressure (all four green LEDs lit).
Remove the second stage regulator from the facepiece by pressing the two release buttons simultaneously.10
Ensure that the needle on the chest mounted pressure gauge reads in the green (FULL) zone.
To remove the second stage from the facepiece first take a deep breath and then press the top of the man-ual override button on the second stage regulator. This stops the flow of air.
9
Verify that the red bypass knob is in the closed position. Fully open the cylinder valve.
Quickly open and close the bypass valve to ensure that it is operating properly.
Fully depress the shutoff button on the second stage regulator.
Remove the second stage regulator from either the waist strap-mounted or shoulder strap-mounted regulator holder by pressing the two release buttons simultaneously.
Place the second stage back into either the waist strap-mounted or shoulder strapmounted regulator holder.
11
8
1 2 3 4
5 6 7A 7B
Honeywell Industrial Safety900 Douglas Pike
Smithfield, RI 02917 USA
US: 800.430.5490
Canada: 888.212.7233
www.honeywellsafety.com
HSPRSP.226Printed in U.S.A.© 2016 Honeywell International Inc.
WARNING! Failure to inspect and correctly maintain your SCBA and/or to replace any damaged components can result in the unit not operating correctly and will expose the user to serious illness, injury or death. Carefully follow all of the cleaning and maintenance procedures outlined in the Honeywell TITAN SCBA Operating and Maintenance Instruction Manual.
