TIN No.37570147098 CST No.37570147098 KBD SUGARS ...staionline.org/Pdf/KBD All.pdf · c) Screening...
Transcript of TIN No.37570147098 CST No.37570147098 KBD SUGARS ...staionline.org/Pdf/KBD All.pdf · c) Screening...
TIN No.37570147098 GST IN NO: 37AAACK5851A1ZU CST No.37570147098
KBD SUGARS & DISTILLERIES LIMITED- SUGAR DIVISION
(Formerly Shree Vaani Sugars & Industries Ltd) Mudipapanapalli Village , Sugalimitta Post, PUNGANUR – 517 247, Chittoor Dist., A.P
E-Mail: [email protected], [email protected]
KBD/GMT/2018/
24th
May, 2018
To
Sub: Lease/sale of 2500 TCD sugar plant with 6 MW co-gen Turbine
With reference to the above subject 2500TCD standard walchand make sugar plant with 6 MW co-gen
provision is ready for sale with 110 acre total land along with good infrastructure and buildings situated in
Mudipapanapalli (village ),Punganur (Taluka ),Chittoor (dist), AP. Or for leasing out basis. Separate
dismantled machineries are not available.
Encl. schedule of machineries -form I(i).
Contact immediately for mobile No: 9480348794/7975639941/matter urgent
With best compliments.
7975639941
KBD SUGARS AND DISTILLERIES LIMITED (Formerly Shree Vaani Sugars & Industries Limited)
PUNGANUR – 517 247, Chittoor Dist. A.P.
FORM – I (i)
SCHEDULE OF MACHINERY
Name of the Factory : KBD SUGARS AND DISTILLERIES LIMITED
MUDIPAPANAPALLI VILLAGE
SUGALIMITTA POST
PUNGANUR – 517 247
CHITTOOR DIST
ANDHRA PRADESH .
Short Name : KUMMARNATHAM
Code No : 34901
Capacity (TCD) Licensed capacity : 2500
Actual capacity : 2500
LICENCE No. & Date : 494 (1989), Dt. 11.07.1989.
Make of the Plant : WALCHANDNAGAR INDUSTRIES
LIMITED, PUNE.
Type of the Plant : SEMI ELECTRIC DRIVE.
(Steam or Semi Electric drive)
Page … 1
I. MILLING PLANT
1. CANE WEIGHMENT : 2 Nos, 30 MTs capacity of Orion make Electro Mechanical
Road Weigh Bridge,
Type: Digital Indicator.
2. CANE UNLOADER & FEEDING
ARRANGEMENT : 3 Nos, Bridges with sling system, 3 motion, 5 T SWL
Electrically operated overhead cranes.
Across the Cane Carrier - 24 Mtrs.
Height from ground - 10 Mtrs
Long Travel - 36 Mtrs
Housing drum drive - 20 HP 960 RPM
Unloading drum drive - 20 HP 960 RPM
Long level drive - 7.5 HP 960 RPM
Gross travel drive - 5.0 HP 960 RPM
(Where the factory has more than one Milling tandem, the particulars required under item 3 to 7 should
be given for each tandem).
3. CANE CARRIER : Size width - 1700 mm
Length between centers - 51.410 Mtrs
Length of horizontal part - 30 Mtrs
Feeding depth - 1.6 Mtrs
Inclination for leveller - 18 Deg.
Details of Chains : 3 strands of chains of 150 mm pitch, tensile strength of
40000 kg/sq.cm, speed 3-7 mtrs. Per minute.
a) Drive H.P if separate drive
steam (or) electric. If electric
state type and range of variable speed : 55 KW, 3 phase, 50 c/s 1475 RPM Motr.
b) Auto cane carrier drive : Dyno drive (Dyno spade)
F.L Torque – 34.90 kgm
Speed – 120-1200 rpm.
Reduction Gear Ratio : Dyno-drive (Dyno spade)
F.L Torque-34.90 kgm
Speed – 120-1200 rpm.
Page … 2
4. FIRST RAKE CARRIER : Width - 1700 mm
Details of chain - 2 strands of chains of229 mm pitch
Tensile Strength - 6000 Kgs per cm.sq.
Speed -10 to 25 Mtr per minute.
Inclination - 45 Deg.
Motor -30 HP, 1460 RPM
Gear Box - 30 HP, 1460 RPM
Ratio - 50 : 1 L
5. PREPARATION OF CANE & CANE KICKER
(a) State No. of sets, number and pitch : One set, 24 Arms (800 thick mounted on 450 dia pipe)
of blades in each set & particulars swing dia 1525 mm clearance from Arm tip to carrier salt
specifying RPM & HP for each set, 1000 mm Motor HP 40, RPM of the kicker 56.7.
clearance between tips & carrier
bed, location of knives (if 2 sets
centre to centre distance).
(b) LEVELLER
Swing Dia : 1600 mm
No. of Sets : One
No. of blades : 32
Pitch : --
HP : 250
RPM : 589
Clearance form knife tip carrier slat : 250 mm
(c) CUTTER
Swing dia : 1675 mm
No. of Sets : One
No. of blades : 48
Pitch : --
HP : 2 Nos Motor 250 HP each (Both side drive)
RPM : 739
Clearance form knife tip carrier slat : 150 mm
Page .. 3
(d) FIBRIZER
Size : 1700 mm
No. of hammers : 120
Shaft Dia : 350
Swing Dia : 1830 mm
Clearance form hammer tip carrier : 50 mm
Slat
Electric Drive : 2 Nos Motor 400 KW each (Both side drive)
RPM : 741
6. CRUSHERS:
State type, Numbers and for each crusher : No crusher provided.
the number of rollers Dia meter and length
of each roller in mm and if splitter type
size of the groove.
7. SHREDDERS:
State type of Shredder and give its : No shredder provided
(a) Size in Centimeter : --
(b) RPM : --
(c) HP of drive & HP used for tonne of
cane : --
(d) Position in mill train : --
8. MILLS:
State number of Mills and for each mill, :1. Four Mills, each mill of 905 mm Dia 1700 mm length
the dia and length or roller in mm. Also consistence of 3 Rollers.
mention if mills have force feed arrangement 2. Under feed rollers provided for 2nd
& 3rd
mill size: 810
their type & No. mm dia x 1680 mm length, TRF Roller provided for
1st & 4
th Mill size: 900 dia.
Give for each Mill:
(a) Type and No. of grooves & size in mm
(Surface & Juice grooves)
Page .. 4
GROOVING DETAILS OF MILL ROLLERS:
Mill Roller Dia Length Pitch
Depth
Groove
Deg.
Angle Landing
1st Mill &
2nd
Mill
Top
Feed
Disc
905
905
905
1700
1700
1700
60
60
60
51.5
66
58
50
40
45
6
6
6
3rd
Mill &
4th
Mill
Top
Feed
Disc
905
905
905
1700
1700
1700
30
30
30
25.73
32.96
28.97
50
40
45
3
3
3
Surface Roller Groove : Mess chart grooves in Feed Roller
No.of
Groove
Pitch Width Depth Chevron Groove
1st Mill 26 60 6 25 No applicable
2nd
Mill 13 120 6 25
3rd
Mill 26 60 6 25
4th
Mill 26 60 6 25
b. Mill settling in mm Tip of Top roller to root of bottom roller & Trash plate setting Tip of top roller to
top
of Trash plate.
Mill I II III IV
Feed Opening (mm) 40 38 30 26
Discharge Opening(mm) 22 17 13 08
Trash Plate setting (mm) 68 55 45 40
c) Type & Setting of Trash Plate : Cast Steel trash plates with vertical bolting arrangement to
Trash
Beam grooving on toe side.
d) Speed of Rollers in meters per minute
and also RPM. :
Mill Surface speed of
Roller on Mtr/Min
RPM
I 10.812 4.051
II 10.676 4.000
III 10.676 4.000
IV 10.543 3.950
. Page .. 5
e) Make and type of Hydraulic system used : M/s Industrial Hydraulic system (Belgaum (India) make) with
accumulators. One each for top roller journal on either side
developing pressure of 250 kg/cm2 and applied on 32 cm dia
Ram. (320 mm).
f) Total hydraulic load on top roller (tonne) : Total hydraulic load on both points of top roller = 353 Ton
and hydraulic load per meter length of Hydraulic load per meter length of Roller 208 Tonnes.
rollers (Tonnes).
g) Length and dia of roller journal in mm : Length 545 mm, Dia meter 430 mm.
h) Hydraulic pressure applied on top roller
of each mill : 2502 kg/sq.cm.
9. A) UNDER FEED ROLLER : 810MM Dia x 1680 mm long (Grooved) for 2nd
and 3rd
mill.
9. B) TRF ROLLER : Ulka make TRF Roller for 1st & 4
th mill, 908 mm dia x
1700 mm long.
10. Donnely Type chute : Fabricated out of 8 mm thk M.S Plate for each, inclination
of 85º with horizental, height of 3 meters
11. Rake Type intermediate carrier : 3 Nos, Length 7.868 mtr width, 1700 mm with an angle of
46º two strands chain of 229 mm pitch and drives of TEFC
motor of 25 HP with 1440 RPM, reduction gear box U
1000 Ratio – 40:1. Speed 10 to 25 mtrs per minit
12. Bagasse Elevator: Type Length and
drive (H.P if separate drive). : Slat type bagasse elevator 29.550 mtrs. Length width 1500
mm, Two strands chain 150mm pitch tensile strength of chain
40000kg Drive Motor 40 HP, 1470 RPM Speed of the carrier: 26
Mtr. Per Min., Gear box U-1200, Ratio – 30:1L.
Page…6
Bagasse Carrier : Effected width 1500 mm, length 4825 mm.
Capacity : 60 T per hr.
Drive : 50 HP, 1440 RPM
Ger Box Ratio : 30 : 1L
Two strands of chain 150 mm pitch tensile strength of chain
40000 kgs, Speed of carrier 25 mtr per minute.
13. DRIVE FOR CRUSHERS AND MILLS
a) If steam Engines are used state no,
And type of /Engines, No. of crusher
and mills driven by each Engine the
diameter of cylinder, stroke, RPM
and Normal HP. : ----
b) If steam Turbines are used their H.P
number & exhaust pressure. ----
c) If Electric motors used, state No. : 4 Nos. DC motor one for each mill KW – 375, RPM -1000.
and type of motors, particulars of Make: Kirloskar.
current, no. of crushers and mills
driven by each motor and HP
developed at full loaded by each
motor.
d) Gearing arrangement, Type : Between each DC Motor and mills one enclosed gear box & one
reduction ratio and type of teeth. Set of spur gear arrangement provided.
1st motion gear box, make: FMG.
Type: SDN 630, Power 500 HP, input & output.
Ratio of f1st enclosed gear box FMG: 34.028:1
No.of teeth of spur gear: 130, Pinion-29, Module: 30
Ratio of spur gear set: 4.448, Total Ratio: 152.55:1
14. IMBIBITION:
a) State whether water used in hot or : For last mill imbibitions with hot water at Temp. of 70º is used.
cold and arrangements provided Water weighed by weighing scale capacity = 2.00 MT.
for measuring (or) weighing.
b) State the imbibitions scheme followed: Compound imbibitions is follows.
Page … 7
c) Screening of juice : Rotary juice screen.
Capacity – 150 TCH cane juice
Drum/Screen dia – 1800 mm
Drum length – 2500 mm (2 Nos 1200 mm long screen bolted
Together).
Welding bar opening – 0.5 mm
Screening area – 13.57 Mw
Drive – 3.7 KW, 1440 RPM with planetary gear box.
Model – KT-2055 and power transmission by heavy duty
simplex
2” pitch chain
Drive sprocket 18 teeth
Driven sprocket 92 teeth
Screen rpm – 10
Wash water pump:
Type - KDS 1575
Capacity – 6 LPS
Head – 68 mtrs
Drive – 11 KW, 2880 rpm.
15. Bearing Lubrication : Centralize Lubrication system
Installed for Mill bearing and Transmission gear bearings.
Make: Lincoln.
16. Mill House E.O.T Crane : 1 No. Make steel and structural capacity 20 Tonns.
17. Crown pinion removal : Hydraulic puller.
Model: KE-HP:150/200
Capacity: 150 MT/200 MT
Working pressure: 480 kg/cmw
Stroke: 150 mm
Make: Kamakshi
Page …8
II. CLARIFICATION PLANT:
1. Measurement (or) weighment of Raw Juice :
a) Measuring equipment : Nil
b) Weighting equipment state number, : One automatic weighing scale having capacity of 6.5
type and weighing capacity per charge MT/tip and 10 tons capacity of check weighment
of each tank in tons and arrangements arrangement as provided. (MAXWELL Boulogno type
provided for recording the number of 2 Nos centrifugal pump (one as stand by) of capacity
tips/hour and other details. 150 M/hr. and 53 mtr head.
2. JUICE HEATERS:
State number, type and heating surface : 5 Nos. of high velocity vertical V-24 type juice heater.
(in sq.m) of each, steam and the purpose Velocity vertical V-24 type juice heater.
for which each is used. Heating surface : 170 M2
No. of tubes : 336
No. of passes : 24
No. of tube/pass : 14
Tube O.D : 45 mm
I.D : 42.6 MM
Length : 4000 mm
Material : S.S
1 No. Dynamic juice heater
Heating surface : 243.35 m2
No. of tubes : 450
No. of passes : 30
No. of tube/pass : 15
Tube O.D : 45 mm
Tube I.D : 42.6 mm
Length : 4000 mm
Material : S.S
Page .. 9
Vapour Line Juice Heater
Heating surface : 240 m2
No. of tubes : 468
No. of passes : 26
No. of tube/pass : 18
Tube O.D : 45 mm
Tube I.D : 42.6 mm
Length : 4000 mm
Material : S.S
One set of Condensate Juice Heater(To heat juice
by condensate)
Heating surface : 138 m2
No. of tubes : 248
No. of passes : 8
No. of tube/pass : 31
Tube O.D : 45 mm
Tube I.D : 42.6 mm
Length : 4000 mm
Material : S.S
One No. Plate Type Juice Heater
Model : AK20
Heat transfer area : 51.0 m2
No. of plate: 104 Nos
No. passes : 1
Plate materials: Alloy 316
Plate thickness : 0.50 mm
Connection : 200 mm
Design pressure : 6 atg
Design Temp: 125º C
Make : Alfa Level
3. JUICE SULPHITATION TANK :
State number, type gross and working : One number continuous juice sulphitation unit with
Capacity in (C.m) of each together with stirrer arrangement, Stirrer rpm: 20,Motor: 5 HP.
Circulation arrangement. RPM: 1440, Gear Box : V-500, Ratio: 70:1,
Capacity : 30.38 M3
Working capacity : 21.90 M3, Working height : 2.5
Mtrs, I.D: 3000 mm, Height : 4300 mm
Page .. 10
4. ELIMINATORS:
State number, type, working capacity : NIL
(in cu.m) and heating surface (in sq.mtr)
of each.
5. SETTLERS:
State Number and working capacity : Rapi dorr Clarifier number of compartment – 5
(in Cu.M) of each in respect of continuous Working capacity : 555 M3 (555 HL), Dia: 9.144 Mtr
settlers mention make, dia, number of Height : 7.620 Mtrs. Juice compartments height:
converted from 242 to 555 system 1.524Mtrs ,compartments and juice holding capacity
6. SULPHUR GAS PLANT : Three Burners
a) Sulphur furnaces – State type and : i) One number of continuous sulphur burner,
number of furnaces, and tray area treay area 0.6 M2.
(in sq.Mtrs) for each furnace continuous
sulphur burner 100 kg/hr.
ii) One No. microprocessor based film type sulphur
burner Capacity : 100 kg/hr., Make: Digital utility,
New Delhi.
iii) One Auto-continuous sulphur burner
Capacity : 100 Kg/hr.
Tray area: 01 Sq.M
Make: Viswa System Pvt. Ltd, Nashik.
b) Air Compressors
State number, type and capacity (in Cu.M) : Three numbers of Rotary type air compressors one
Displacement per minute) of each and for juice sulphitation and syrup sulphitation
Delivery pressure. having Capacity of 600 m33/hr each.
Delivery pressure : 1.0 kgs/cm2 and one as
stand by.
7. FILTERATION EQUIPMENT:
a) Rotary vacuum filter make, number and : Oliver Cambell vacuum filter: 2 Nos
diameter, length of each and filtering Dia: 2.44 Mtrs, Length: 4.876 Mtrs. (8’ x 16’)
area with details of screens. Each filtering area 37.36 mw (402 Sq,.ft). Stainless
steel screens of hole size 0.5 mm., Number of holes:
625 Sq.inch.
b) Vacuum Pump : 3 Nos. Vacuum pump, Type: DV 40, Capacity: 73.5
M3/hr.1450 rpm.
Page … 11
8. MILK OF LIME PLANT:
a) Give details of lime slaker,
type, size and RPM etc. : a) Rotary type of lime slakar of mild steel construction
and complete with electric drive. Lime slaker dia 0.90
Mtrs, Length 3.95 Mtrs. RPM. 29.
b) One lime classifier working in conjunction with slaker.
c) Two numbers of milk of lime storage tanks. Each
having dia: 3 Mtrs, Height: 3.85 Mtrs,
Capacity: 27.20 Cu.Mtrs., Stirrer R.P.M: 20
d) Two numbers of milk of lime pumps each having
capacity of 37.5 Cu.m/hr.
e) Grit catchers are provided for lime pumps.
f) One hydro cyclone provided.
b) Give details of country kiln capacity : NIL.
9. CARBONATION PLANT:
(To be filled up only for the factories : NIL
following carbonation process for
clarification of juice).
a) Carbonaiton tanks-State seperately : NIL
for each set the number iof tanks and
the working capacity in (Cubic Metre)
and the heating surface (in sq. Mtr)
of each tank, also gross capacity.
b) Lime-Kiln. : -----
(i) State number and capacity
(in cubic metre)
(ii) Give particulars of apparatus
if any, provided for analysis
of gas.
Page …12
c) Gas pump-Sate number and capacity : ----
in cubic meter displacement (per minute)
of each type whether steam driven or
electric driven whether rotary or
reciprocation and type of valves.
Alternative Equipment :
Give here any alternative particulars of
Equipment if any in place of any of the
Proceeding items, such as dorr clarified,
Continuous sulphitation.
Syrup Sulpnhitation : ---
III. EVAPORATION AND BOILING PLANT:
i) Evaporators:
(The vessel from which vapours are
bled should be specified stating the
use to which the bled vapours are
put to)
a) State number and for each evaporator the : Details given below.
Number of vessels and the total heating
Surface(in Sq.Mts) of each vessel together
With dimensions of tubes, dia, and height
Of body and size of vapour pipes of each
body.
Particulars Heating
Surface
In M2
Details of S.S Tubes No of
Tubes
Body
Dia
mm
Body
Hgt
Mm
Vapour
Pipe dia
mm I.D
Mm
O.D
mm
Length
mm
1st pressure
effect V.C
880 38.85 41.25 4000 1796 3200 5530 700
2nd
pressure
effect V.C.
880 38.85 41.25 4000 1796 3200 5530 800
1st Body Quad 450 42.60 45.00 2000 1694 2800 4000 500
2nd
Body Quad 600 42.60 45.00 2000 2244 ID 3250 4000 700
3RD
Body Quad A.
B.
450
300
42.60
42.60
45.00
45.00
2000
2000
1694
1130
2800
2400
4000
5000
700
600
4th
Body Quad 450 42.60 45.00 2000 1694 2800 4000 900
Page .. 13
VAPOUR BLEEDING ARRANGEMENT.
i) Semi kestner vapour bleed to Evaporator, sulphited juice (1st heating) clear juice heating
(1st stage) and Pans.
ii) Raw juice heating 1st stage, through vapour line juice heater using V body vapour. Raw juice
heating IInd stage through condensate juice heater using combind condensate water coming out
from cigar. Raw juice III stage heating through Dynamic juice heater using IV body vapour.
b) Give particulars of apparatus, if any
provided for recording and controlling.
i) Density of syrup : Density of syrup by brix hydrometers.
ii) Vacuum in last body : Vacuum by Vacuum guages.
c) State the heating surface of pre-evaporator
if any provided : Double pressure effects details are given.
d) Details of save-all and juice catchers : Centrifugal type save-all.
e) Arrangements for drawing condensate : i) Semi kestner condensate used for boiler by
from vessels providing separate mond.
ii) Evaporators, juice heaters and pans condensate
are withdrawn through cigar and vapour flash is
utilized for evaporators.
2) Syrup Treatment Plant:
a) Sulphuring tanks. : One continuous syrup sulphitation vessel.
State number and working capacities Working capacity : 6.44 Cu.Mtrs.
(in cubic meter) and gross capacities and Gross capacity : 10.05 Cu.Mtrs
whether continuous (or) intermittent. Working height : 1.8 Mtrs.
b) Filters – State type, number and filtering : i) Syrup clarification system of capacity suitable
for 3000 TCD plant.
(in Sq.Mtrs) (Particulars to type of filter ii) E-Melt system for sulphur melting.
press may be omitted if desired). iii) So2 water system.
Capacity : 230 TCH (5000 TCD)
Make: Digital Utilities, New Delhi.
Syrup clarifier capacity 160 H.L.
Buffer tank capacity 230 H.L
3) Syrup Storage.
State number of tanks and capacity : 4 Nos of storage tanks of 20.0 Cu.Mtrs. capacity
(in cubic Mtrs. of each) each.
Page …14
4) Molasses Storage (Process). : 11 Nos 20.0 Cu.Mtrs. capacity each
State number of tanks and capacity (Melt-1 Tank: A.L-1 Tank: A.H-4 Tanks, B.H-3
(in Cu.Mtrs. of each). Tank, C.L-2 Tanks).
5) Vacuum Pans:
a) State type and number of Pans of each type : 6 Nos, if Calandria Pans, each of striking capacity
(Coil or Calandria) and for each pan state 60 MTs. (420 HL) details given below, tube
the normal strike capacity (in Hecto Litrs) material S.S.
and total heating surface in Sq.Mtrs. and the
mechanical circulators if any, (Dia, Pitch
and RPM) and the size of the tubes or coil
in Sq.Mtrs.
Pan
No.
Heating
Surface
In M2
Details of S.S Tubes No. of
Tubes
Body
Dia
In mm
Strike
Valume
In H.L
Vapour
Pipe
Dia in
mm
I.D.
MM
O.D
MM
Length
MM
1. 277.55 98.0 102 900 1064 4900 420 1100
2. 277.55 98.0 102 900 1064 4900 420 1200
3. 277.55 98.0 102 900 1064 4900 420 1200
4. 277.55 98.0 102 900 1064 4900 420 1200
5. 277.55 98.0 102 900 1064 4900 420 1200
6. 277.55 98.0 102 900 1064 4900 420 1200
b) Give particulars of apparatus if any provided
i) For recording vacuum : Vacuum Gauges
ii) For controlling boiling pan : --
iii) Details of save-all & Juice catchers : Helmet type save-alls
iv) Details of Booster if any :
6) Condensation Plant:
a) Condenses, state number, type dia and : Individual S.S condensers for Pan No.1,2,3,4,5,6
height (in cms) also give particulars of and Evaporator IV., Make: Spray Engineering.
pans and evaporators connected to each 1st pan Multi jet condensate replaced by SS
condensers. Condenser.
Page …15
b) Condenser water pumps, State No, type, : For Pans 3 Nos, 1500 m 3/hr, 25 MTs head type-
capacity (Lits/hr) for each Centrifugal, Drive-150 HP, 1480 RPM, Make:Sam,
Greaves Cotton. 1 No. 2500 M3/hr capacity had –
24 Mtrs, Type: MF 40 x 40, 250 HP, 978 RPM
For Evaporator: Type – 250 MF, Capacity – 450 –
500 M3/hr. Head-25 mtr, Make-Gita,
Drive:55 KW, 1480 rpm.
c) Air Pumps: State number, type and : ---
capacity (in cubic meter displacement/
min. for each)
d) Water cooling system:
i) Spray pump-State number & type and : 2 Nos. each having a capacity of 2500 Cu.Mtrs/hr.
capacity (in lts/hr) for each. Type: M.P 450/550 drive. 90 KW/93KW, 975 RPM.
1 No. Gita make Type:250 MF, Capacity:800 M3/hr
Head – 11 mtr., Drive – 55 KW, 1480 rpm.
ii) Spray pond-State number & Type of : One mist flow spray pond size: 100 mtr x 26.5 mm
Nozzels. Mtr, 410 nozzles, involute type.
iii) Cooling Tower-Sgtaet Platform area : Cooling Tower is provided with 4 Fans.
(in M2). Dimensions: Width : 9855 mm
Length: 19660 mm
Height: 6553 mm
Fan Drive H.P : 30
IV. Condensate hot water cooling Tower : Type: Natural Cooling. No.of Nozzels: 24
Capacity: 15m3/hr., 3 Nos Pumps,
Flow range 4 to 2.5 ltr/sec., Head: 30 mtr.
Drive: 2.2 KW, RPM: 2880.
V. Pan discharge valve operation : 2 Nos Hydraulic operated system provided for
Operation of discharge valve of Pan No. 2 & 3.,
Make: Kamkshi.
Page .. 16
VI) Cooling, curing and drying Plant:
1. Crystallizers:
State number of crystallizers of each type : 4 Nos. of Air cooled “U” shaped crystallizers for “A”
(open (or) closed and jacketed etc) and for “A” massecuite. Capacity: 420 H.L-3 Nos & 455 HL
each crystallizer give the normal massecuite Capacity-1 No. 3 nos of water cooled “U” shaped
cooled and the cooling surface (in M2 of crystallizers for “B” massecuite. Capacity: 455 HL
coils if any type of cooling coils. each Cooling surface area – 68 sq. Mtrs. each
2 Nos of Air cooled crystallizers (“U” shaped) for
C-massecuite strike receivers, capacity: 420 H.L
each. One number mono- overtical crystallizer for
C-massecuite cooling. Capacity: 1750 H.L Cooling
Surface area: 380 Sq.Mtrs.
2. Seed Crystallizers:
a) Mention number and size (in hecto liters) : Four No’s out of which one open crystallizer for
for each. B-seed of Capacity: 325 H.L.
One vacuum crystallizer for A-footing of capacity
325 HL and One vacuum crystallizer for B-grain of
capacity 325 H.L and one vacuum crystallizer for
B-grain of capacity 325
H.L and one vacuum crystallizer of C-grain of
capacity 325 H.L All these crystallizers are provided
with planetary gears for power saving.
b) Give details of reheating arrangement : C-fore worker Pug Mill is provided with transient
heaters with hot water re-heating arrangement.
3. Centrifugal Machines
a) State number of machines used as fore : Details of Centrifugal machine given below.
Workers and After workers separately
for each type of Massecuite and mention
separately their basket diameter and
height (in mm) R.P.M and type of
drive.
b) Give gravity factor and particulars of
high speed machines if any such as size
cubic content, speed and number of
cycles/hour low grade massecuites
particulars of liners and packing.
Page…17
Massecuite
Machine Basket
R.P.M Drive
Gravity Factor (max)
Capacity MT/Hr per Machine
No.of cycles per hr.
per Machine
Liner
Type Nos Type Size Top Inner
1 2 3 4 5 6 7 8 9 10 11 12
A. Fully Automatic
flat bottom
6
Flat bottom
48"/30" 1450 4-Speed pole changing motor
80/200/750/1450
1430 9.80 MT 14 Brass 8.5
mm 8
mech
B. Continuous Centrifugal
2 30 Semi cone angle
1350 mm
1450 120 HP 1580 15 to 18 MTs per
hour
Nickel screen 0.09 % 2.20 mm
C-Fore worker
Continuous Centrifugal
2 30 Semi cone angle
1350 mm
1750 120 HP 2300 8 to 12
MTs per hour
Nickel screen 0.06 % 2.20 mm
C-After worker
Continuous Centrifugal
1 30 Semi
cone angle
1350 mm
1450 120 HP 1580 15 to 18 Mts per
hour
Nickel screen
0.09% 2.2 mm
Air compressors : 2 Nos Air compressors
1 No. Ingersoll Ran d make, Size: 8 x 5 ESV-1-LUB
Pressure-100 lbs/sq.inches RPM-750
1 No. Kirloskar Khosla make, Model:SFS 325, HP: 50,
Water cooled.
Capacity and pressure of hydraulic pump : 1 No. of super hated wash water unit to supply spray water
For centrifugals. for Centrifugals.
4. SUGAR DRIER:
a) State number and type (eg) : Grass hoppers – 3 No’s
Granulator, Grass Hopper, Cooling i) First one plain tray hopper.
Tower etc) and total heating surface ii) Second one multi tray hopper with hot air supply.
(in m2) iii) Third one multi tray hopper with cold air supply.
First hopper: Length : 12800 mm
Width : 1500 mm
Depth : 230 mm
Second hopper: Length : 12000 mm
Width : 1500 mm
Depth : 230 mm
Third hopper: Length : 12800 mm
Width : 1500 mm
Depth : 230 mm
Heating Surface: 18 Sq.Mts
iv) One magnetic separator installed over 3rd
sugar hopper
to remove iron particles from sugar.
b) Sugar Elevator : 1 No. Sugar elevator (bucket type) having M.S galvanized
buckets mounted on 2 chain stand. Capacity : 12 Tonns/hr.
c) Sugar Grader : 2 No’s four deck sugar graders of Ravalgoan make,
vibrating type, each of 12 MTs/hr capacity.
d) Sugar Weighing scales : 3 No’s Electronic Weighing scale Model:DS415 series
Capacity: 300 kg – 1 Nos
200 kg – 2 Nos
e) Bag stitching machine : 3 No’s bag stitching machines of capacity 150 bags per
hour, Make: Stitch well Qualitex.
page…19
f) Sugar Bag Slacker : 3 No’s
g) Sugar Bag conveyor : 16 Nos
600 mm width, 6.1 meter long – 2 Nos
7.8 meter long – 2 Nos
9.1 meter long – 12 Nos.
h) Sugar bag printing machine : 1 No., Make: Drava.
i) Sugar Melter : 1 No. Capacity : 15 M3/hr. with stirrer drive arrangement.
5. Sugar Silo (Bin) : a) 1 No Food grade type sugar silo of Rostfrei make holding
Capacity 110 Tons.
b) Automatic weighing machines of Hi-tech make – 2 Nos
Each capacity 20 Tons . Per hour
6. Sugar Go down : 3 No’s Size – 80 mtr x 40 meter – 1 No.
80 mrt x 20 meter – 2 No’s
Capacity: 300000 Bags (Qtls)
V. STEAM & POWER PLANT:
1. a) Boilers
State numbers, type and make of boilers : i) Number off: One
and for each boiler it’s working pressure ii) Type-Bent water tube boiler with side water walls.
(in kgs. Per sq.cm), hating surface (Indian iii) Make – M/s Thermax Babcock & Wilcox Ltd.
rating), steam generating capacity in Kg. iv) Working pressure – 42 kg/cm2
per hour,grate are for Bagasse and coal v) Heating surface furnace & Bank tubes – 1785 M2
(in sq.mtrs) super heater heating surface Economizer - 895 M2
and degrees of super heat and details of Super Heater coil - 160 <2
soot blower. vi) Steam Generating capacity – 64 TPH.
vii) Travelling Grate Furnace area 4.92 Sq.,
viii) Super heated steam temperature 390º C C+10º
C-15º C.
ix) Soot Blower-4 Nos at various levels in Boiler and
4 Nos in economizer.
b) Feed water Treatment:
Give particulars of arrangements if any, : DM plant is provided
for softening or other wise treating the Make : ION Exchange
feed water entering the boiler. Having: Multigrade Filter, cat ion unit, Degasification
system, Anion unit.
Capacity: 200 M3/24 hrs.
Storage tank: M.S.Cylinderical tank capacity: 50 M3.
c) Economizer and Feed water heaters:
Give particulars stating type and heating : Feed water heating economizer is provided &
Surface. Economize heating surface = 895 Sq. Meters.
d) State accumulators-Number, Type and
capacity : ---
Pate…20
e) Auxiliary fuel:
Give particulars of arrangements for : Coal and Fire wood.
burning auxiliary fuel, if any (e.g,Crude
Oil, Molasses, coal etc.)
f) Chimney :
State if it is of cricks or of steel and give : R.C.C. Chimney - 1 No.
diameter and height. Also type of draught Diameter – 3 Meter, Height – 40 Mtr., Draughts –
(eg) forced, induced or natural) capacity 1 No. Secondary Air Fan Capacity – 47640 M3/hr.
of froced and induced draught fans. Model – RPM 1630 A SZ 108 SWSI, arr-3–CCW
Drive – 160 KW,1485 RPM,
1 No. F.D Fan.
Make – Industrial Fans (India) Pvt.Ltd
Capacity : 80000 M3/hr.
Fan RPM – 1120 (Belt drive)
Drive : V Belt
Shaft power- 46.29 KW
2 Nos I.D Fan, Make: Enviro division (Thermax)
Capacity : 117600 M3/hr., Drive: 187 KW,
740 RPM each.
g) Fly ash Arrester : Multi cyclone dust collector with air lock valve.
Increased cyclone cells from 156 to 228 Nos and
Adding one more rotary air valve.
h) Feed water tank : M.S Cylinderical tank
Size: 3000 mm dia, 9226 mm long,
Capacity: 60 M3
i) De Aerator storage tank : Capacity: 54 M3, Normal water level-40 M3
Size: 2800 mm dia, 9606 mm long.
j) Feed Pump : 3 Nos KSB make pump, Type: WL 80/10
Capacity: 50 M3/hr. Head-560 mtr. (M/c)
Drive – 132 KW, 2975 RPM each.
1 No. Turbo Feed pump capacity: 135 M3/hr,
Head-5602 mtr., Turbine HP 296 KW, 2930 RPM.
3 Nos Transfer pump Make: Kirloskar, Model: CPG
50/200, Capacity – 50 M3/hr.Head-55 mtr. Drive:
11.18 KW, 2900 RPM each.
Page…21
k) Chemical dosing pump : L.P Chemical dosing pump, Capacity : 16.8 LPH
HP Chemical dosing pump capacity : 20 LPH.
l) Compressor : 4 Nos, Make : Ingersollrand- 2 Nos of Type 30
Size: 5” & 2 ¾” x 3 ½”, Drive: 5.5 KW, 1440 RPM
2 Nos, of Model 2475, Drive: 7.5 HP, 1440 RPM.
m) Continuous Bagasse feeding system : 4 sets, Drum extractor: 800 mm dia
Casting length: 1650 mm, Drive: 5.5 KW, RPM: 960
Planetary gear type: KT 4009 M, Ratio: 307.9.1
Output speed: 2.4 rpm.
Screw conveyor: Width – 627 mm, Length – 2330 mm
Drive: 3.7 KW,RPM: 1440. Planetary gear KT 2005 M
Ratio: 27:7:1, Output speed: 51 rpm.
n) Coal & Wood Chips handling equipments
and Belt conveyors for co-gen plant.
i) Straight Conveyor : Width of the Belt : 910 mm
Rubber Belt : 3 ply
Thickness : 10 mm
Length of the Conveyor : 80.45 Mtr
Drive H.P : 15 H.P
Size of Gear box : 4.700
ii) Inclined Conveyor : Width of the Belt : 910 mm
Rubber Belt : 3 Ply
Thickness : 10 mm
Length of the Conveyor : 24.25 Mtrs
Drive H.P : 5 H.P
Size of the Gear Box : 4 knifes
iii) Coal handling equipment : a) Coal crushers, Make: - , H.P: 25 HP.
b) Coal Conveyor
Length of coal conveyor: 10.85 Mtrs
Belt width : 500 mm
Belt Thickness : 6 mm
3 Ply Rubber Belt.
iv) Wood Chipping Machine : Make : CIBI
Capacity : 10 Tonns/Hr.
H.P : 145 H.P
No. of knifes : 4 knife
Page…22
2. POWER PLANT : 2.5 MW
a) Sate number of prime movers, stating
for each : ---
i) The purpose for which used it’s make,
cylinder diameter stroke RPM and normal
H.P or B.H.P : ---
ii) If any turbine is also used, state it’s type : Make: Triveni, Frame: 14 A, S. No.F 14 A-048-
number of stages and steam conditions 1991, Power 2500 KW,
of inlet and outlet. Rotor Gear sped 8250/1500 RPM
Trip speed: 1650 RPM,
Steam pressure: 42/45 kg /cm2
Exhaust pressure: 1.2/1.5 kg/cm2,
Steam temperature 425º C/445ºC.
b) State number of electric generators s
stating for each : Alternator, Make: Kirloskar, Frame: 4 AB 710/6
KVA – 3125, RPM – 1500, Volt – 420, Amp –
4296.
i) D.C, or A,C : 1 No. A.C set
ii) Voltage and make : 440 Volts, M/s. Kirloskar.
iii) Out put in K.W : 2500 K.W
iv) Purpose for which used : Generation of power for lighting as well as running
(Lighting only or development of of factory units.
power in factory).
v) If A.C power factor number of phase : Power factory = 0.8
and frequency
.
vi) Maximum demand in KW during the : Maximum demand in season = 2400 K.W
season and the off season In off season power turbine is not in operation.
vii) KW hour generated during the season : ---
viii) KW hour generated during the off
season : Nil
2-A) POWER PLANT : 5.0 MW
a) Sate number of prime movers, stating
for each : ---
i) The purpose for which used it’s make,
cylinder diameter stroke RPM and normal
H.P or B.H.P : ---
Page..23
ii) If any turbine is also used, state it’s type : Make: W.H Allen Sons & Company Ltd, Bedford,
England.
number of stages and steam conditions Year : 1968, Sl.No. T4/67359
of inlet and outlet. Power – 5000 KW
Normal running speed: 10250 rpm
Trip speed – 11275 rpm.
Inlet pressure – 44 brg(625 psig)
Exhaust pressure – Minimum 15 psig, Max. 45 psig
Steam temperature: 780 deg. F (415 Deg. C)
Max. inlet temp. – 850 Deg. F (415 Deg.)
Steam consumption – 42184.52 kg/hr at 5.0 MW load
~ 8.44 kg/KWHr.
Gear box input rpm: 10250
Gear box output rpm: 1500
b) State number of electric generators
stating for each. : Alternator, Make: Lancashire Dynamo & Crypto Ltd,
England
Type – Brushless AC Exciter, Sl.No. 371260
Enclosure – C.A.C.W. Size: EAD 60
Standard – B.S.2613/1957 Class B
Year – 1967
Max. Cont. Rating – 6250 KVA (5000 KW
@ 0.8 power factor)
Voltage – 3300 V
Frequency – 50 Hz
No. of phase – 3
Speed – 1500 rpm
x) Diesel set : i) 1 No. Model 320-26, KW=250, PF=0.8, 3 phase,
50 cycles/second, V=415 V,KVA=320,
RPM:Make: Powerica.
ii) 1 No. 500 KVA D.G set
Type: W6AG, RPM: 1000,
Make:Kirloskar Oil Engine Ltd, Pune.
Generator : 500 KVA, Speed: 1000 RPM,
Volts: 415,
Amps: 696, Make: Jyothi.
xi) Transformer : 2500 KVA 11 KV/433 V – 1 No.
6000 KVA 11 KV 433 – 1 No.
3000KVA 11 KV 433 – 1No
Page…24
CO-GEN CAPTIVE POWER PLANT : 6.0 M.W
TURBINE: Make: Triveni Engineering
Model: FR 13, Steam
Pressure: 42 kg/cm2
Temperature : 400º C
Serial No; : 41, Year-2002
Power : 6000 KW
Turbine speed : 8312 RPM
Output speed : 1500 RPM
Trip speed range : 9145 to 9560 rpm
1st Critical speed : 3200 to 3600
Bleeding steam pr : 7 kg/cm2
Exhaust steam pr : 0.1 kg/cm2
Extraction : 1.5 kg/cm2
Gear Box : Triveni make
Model : 0560
Sl. No. : 03
Gear Ratio : 5.54
Power HP/KW : 6600 KW
Rated input : 8312
Rated output : 1500
Service Factor : 1.5
No. of Teeth : Gear/Pinion-
138/25
CONDENSOR : 1 No.
Make : TEAM Indian Limited
Type : Surface fixed tube type
No. of Pass : Two water box type divided
Steam Flow : 29500 kg/hr,
Steam Pressure-ATA 0.12
Steam Temp. – 49.5º C
Clearness factor : 0.85
Cooling water temp. inlet 32º C
Outlet 42º C
Cooling water pressure 0.3 kg/cm2
Cooling water quantity : 1578 m3/hr
Surface area : 557.2 m2
COOLING TOWER : 1 No. Masonry cooling tower Fan
drive: 60 HP,
1480 RPM, Fan dia: 4250 mm,
Type : Two cells.
Page…25
SPRAY PUMP : 2 Nos
Pump No. 1 Pump No. 2
Make : Kirloskar Beacon weir Lt
Type : 14 UP 1M SDA
Head : 25 mtr 35 mtr.
Capacity : 486 ltr/sec. 444.44 ltr/sec
Size : 400 x 350 300 x 400
Drive : 180 KW 187 KW
RPM : 1480 1478
ALTERNATER : Make : BHEL
Frame : G74904
KVA : 7500
KW : 6000
RPM : 1500
Voltage : 11 KV
P.F : 0.8
Starter AMP : 394
Phase :3,
Hz : 50
Connection star
Ambient Temp.: 50º C
Inlet Temp : 50º C
Exct Volt : 125
Exct Amps : 406
Specification: IS4722
Duty: Continuous
Brushless excitor : Make : BHEL
Kw : 62.6
Excitation Amp: 3.6 A
Excitation Volt : 108 A
Connection : Star
Volts : 139
Amp : 450
RPM : 1500
Hz : 150
Specification: IS 4722
Makers No. : 222A 231-11
Division : Bhopal
Year : 2001
Page…26
TRANSFORMER : 1 No.
Rated MVA : 8 MVA
Voltage : 11 KV/33KV
VI GENERAL
i) Make of Plant:
State name of maker or principal makers of : Walchandnagar Industries Ltd., & Thermax
machinery Babcock & Wilcox Ltd., Triveni
Engineering, Dorr Oliver, Nizam Sugars
Spray Engineering, Kirloskar,
BHEL, Digital Utilities.
ii) Final Molasses Storage Tank State Number,
type and capacity of each tank : 2 No’s, steel storage tanks,
Capacity: 3077 Cu.Mtrs each.
iii) Effluent Disposal:
Give particulars of arrangements for disposal : Effluent treatment plant is provided with
Of factory effluents anaerobic lagoon, Oxidation pond with
Aerators and with Second clarifier etc.
Treated effluent is utilized for irrigation
purpose
Capacity: 3500 M3/day.
Upgraded ETP by adopting diffuser system
and adding one more clarifier.
iv) Sampling equipment:
Give particulars of equipment provided for : Automatic sampling for mixed juice hand
Sampling various juices, bagasse and other sampling at all other stages.
Material for analysis.
v) Control instruments:
Number of specification : Pressure, Vacuum and temperature gauges
are arranged wherever required for pans and
evaporators.
VRL Automation have provided for Boiler
control Panel. (Steam Flow, Water flow, Co2
recorder Drought gauges, pressure and temp.
guages for water and steam, ID & FD Damper
control arrangement).
VRL Automation of PRD station 42 kg/cm2 7
kg/cm2 and 7 kg/cm2 to 1 kg/cm.
VRL Automation for Raw Juice and imbibition
water flow & Control System.
Page…27
VRL Automation of sulphited juice and sulphur
burner.
vi) Final Molasses weightment : One automatic weighing scale is provided of
capacity 3.0 MTs/tip.
vii) Details of the machinery of workshop:
a) State number of Laths and their sizes : 3 Nos
Make, Type, size, HP, maximum speed
Minimum speed : Centre height : 12”, Length of bed: 6 feet,
HP: 2, RPM: 1440
b) Imported Lathe Make: Lodge & Shipley
M/c USA Bed Length: 4 feet, Drive, 3 HP
1440 RPM.
c) Lathe Machine Make: Kirloskar,
Bed Length: 7 feet, Drive H.P : 3 HP,
d) Roller Lathe Make: G.R.D.,
Bed Length: 24 feet, Drive H.P: 15 .
e) Radian Drilling Machine,
Make: Archadle England,
Height: 10 feet, Drive: 3 HP.
g) Number of shapping machines : 1 No. HP:3, Make: Leader,Maximum
stroke 24”, minimum stroke
h) Couple size and capacity : ---
i) Planning machines and their sizes : ---
j) Other smaller items in the (Workshop):
1. Power Hacksaw Machine : 1 No.
Make: J.E.W Ram Length: 545 mm
Ram Width: 155 mm, Blade
Length: 525,Motor: Belco, KW:
1.5, HP: 2, Amps: 3.3, Volts: 415, RPM
1440,M/c NO. 23371, Frame: 90
2. Grinding Machine : 1 No
Make: I.F.I., Frame: BGM/MD, Wheel
size:8”x 1” x 3/4m GOL 0.8, Amps: 1.4,
Volts: 400/400,Cos 0.8, RPM: 2860
Rating: INT, S.No.4241/91.
Page ..28
3. Sensitive Drilling Machine : 1 No.
Drill size:1” (25.4mm), Basic plate dia: 350 mm
Motor: Accurate 30 induction motor, KW: 0.75
HP: 01, RPM: 1440, Insulation class E,
M/c No. 2130.
4) Light duty Gun type Drilling : 1 No.
Make: Ralliwolf, Type: EJ36,
Drill: 010
Duty: 15 minutes, Code EVolts235,
Watts: 235 F/L Amps 3.0, RPM: 700,
S.No.D69934.
5) Magnetic Drilling Machine : 1 No.
Make: Ralliwolf, Type: NW10, Code: AR,
Drill: 031,F/L Amps 3.8, Volts: 235,
Watts: 850, RPM: 280, S.No. C3480
6. Light Duty Drilling Machine : 1 No.
Make: Ralliwolf, Size: 1/2:”, RPM: 1440
7. Portable Blower : 1 No.
Make: Neutron (Pvt) Ltd
Type: N21B, F/L Amps: 1.65 AC & DC 235
RPM: 1.55 M3/Minutes 310 KM PH,
S.No.580590
8. High Speed Angular Grinder : 1 No.
Make: Ralliwalf, Type: Ag7, Wheel: 180,
Code BP, F/L Amps: 10, M/L RPM: 7000,
Duty cycles: 30 mts, S.No. C66655
9. Flexible Shaft-Grinder : 2 Nos
Ralliwolf machine, Type: FF2,
Collect 60, Code:
D, Volts 235, Watts: 370 F/L /amps: 1.7,
M/L RPM: 11500/1200, Duty
cycles: 30 min.
10. Air Blower Machine : 1 No.
Make: Ralliwolf, Model: 77750 Head:
750/4802mm Cap: 20/1, 6M3/Minute,
Amps: 3.5/2.4, S.No.BL118354 Double
Insulation.
Page…29
11. Straight Grinding Machine : 1 No.
Make: Ralliwolf, Type: MQ7, Wheel Dia: 100 mm
Code: BP, Watts: 750, RPM: 5000, Duty cycle: 30
Minutes, S.No. 1303127.
12. 3” Radial Drilling Machine : 1 No., Make: Archdale England
13. Welding Transformer : 6 Nos
14. Welding Generator : 1 No.
15. Plate Bending machine : 1 No. width: 2500 mm.
16. Cold water arrangement : 8 Bore wells,
7.5 HP submersible pump – 6 Nos 15 HP
submersible pump – 2 Nos
17. Cold Water storage : One masonry tank.
Size: 50 Mtrr dia, 2.5 Mtr, depth capacity: 4700
Cum.Mtr.
18. Power House Crane : 1 No. Make: Steel and structural capacity: 20
Tonnes
19. Reverse Osmosis Plant : R.O Plant Make : Wellknown,
Capacity : 50 Tons/hr
Discharge: 30 Tons,
Reject Water:20 Tons/hr.
20. Ultra Filter Plant : Capacity : 40 Tons/hr.
I hereby declare that all the details given in this returns are true to the best of my knowledge and belief.
Signature of the Owner or Person Authorized.
D.K.AUDIKESAVULU
CHAIRMAN/MANAGING DIRECTOR
Page…30
KBD SUGARS & DISTILLERIES LIMITED - PUNGANUR
SUGARCANE AREA AVAILABLE FOR 2018-'19 CRUSHING SEASON
Existing sugarcane area; As on
31/05/2017
Sl.no DIVISION Plant
Ac Ratoon
Ac Total
Ac
Further expected
plantation Ac
1 PUNGANUR 461 429 890 30 2 CHOWDEPALLI 855 409 1264 50 3 GANGAVARAM 504 351 855 25 4 V.KOTA 356 22 378 30 5 MADANAPALLI 20 0 20 10
TOTAL AREA (AC) 2196 1211 3407 145
MANDAL WISE EXISTING SUGARCANE AREA FOR 2018-'19 CRUSHING SEASON
SL NO.,
NAME OF THE MANDAL SUGARCANE EXTENT FOR 2018 - '19 ESTIMATED YIELD., MT
P R G.TOTAL., AC P R G.TOTAL., MT
1 PUNGANUR 231.05 250.29 481.34 5776.25 5005.8 10782.05
2 RAMASAMUDRAM 23 32.54 55.54 575 650.8 1225.8
3 PEDDA PANJANI 162.98 42.56 205.54 4074.5 851.2 4925.7
4 CHOWDE PALLI 587.05 345.23 932.28 14676.25 6904.6 21580.85
5 SOMALA 89.26 16.3 105.56 2231.5 326 2557.5
6 SADUM 11.5 14 25.5 287.5 280 567.5
7 GANGAVARAM 464 321.15 785.15 11600 6423 18023
8 BAI REDDY PALLI 164.25 118.85 283.1 4106.25 2377 6483.25
9 V-KOTA 200 25 225 5000 500 5500
10 RAMA KUPPAM 54 6 60 1350 120 1470
11 SHANTHI PURAM 170 29 199 4250 580 4830
12 KUPPAM 0 0 0 0 0 0
13 MADANA PALLI 1 0 1 25 0 25
14 KALIKIRI 5.5 0 5.5 137.5 0 137.5
15 GUDU PALLI 0 0 0 0 0 0
16 MOLAKALA CHERUVU 0 0 0 0 0 0
17 GURRAM KONDA 0 4.5 4.5 0 90 90
18 KURABALA KOTA 0 0 0 0 0 0
19 B-KOTHA KOTA 9.2 2 11.2 230 40 270
20 P.T.M 3 0 3 75 0 75
21 VOYAL PADU 1 8.5 9.5 25 170 195
22 THAMBALLA PALLI 0 0 0 0 0 0
23 NIMMANA PALLI 1 14 15 25 280 305
24 PALAMANER 0 0 0 0 0 0
25 PADDAMANDYAM 0 0 0 0 0 0
TOTAL ., AC 2177.79 1229.92 3407.71 54444.75 24598.4 79043.15
K.VARADARAJAN
AGM- CANE
KB.D- Sqge€: Zorr. trlop
,&9sf$.-r6d
E
'$"c\r,,
s;r*i
L#1s'4,!o
M
$o*;d"$,
Nota:
-r
7t6lz
rlcndnlt'
Ra.cnue villaf ,