Time Pass Programming Manual · 2016. 5. 17. · timepass paystation multiplexer (49-9429)...
Transcript of Time Pass Programming Manual · 2016. 5. 17. · timepass paystation multiplexer (49-9429)...
Document #101-0150 1 7/18/08
Time Pass® ProgrammingManual
Document #101-0150 2 7/18/08
TABLE OF CONTENTS
TIME PASS OVERVIEW ........................................................................................... 4TIME PASS WIRING SCHEMATIC ....................................................................... 5INTERFACE BOX ....................................................................................................... 6TIME PASS WIRING SCHEMATIC ....................................................................... 7TIME PASS ................................................................................................................... 8
HAND-HELD ............................................................................................................. 91-3 SHIFTS .............................................................................................................. 10
VERIFY CODES ................................................................................................ 101-3 SHIFTS .............................................................................................................. 12
EXIT.................................................................................................................... 12MANAGER .............................................................................................................. 14
FOOTER MESSAGE ................................................................................................................ 14EXAMPLE................................................................................................................................. 16
PASSWORD SETTING.......................................................................................... 18DISPLAY CLOCK .................................................................................................................... 20CHANGE TIME ........................................................................................................................ 21PERIOD REPORT ..................................................................................................................... 22DISP. MAN REPORT..... ........................................................................................................... 24DISP. ACW REPORT ................................................................................................................ 26
INSTALLER ............................................................................................................ 28BASIC RATES $$$ .................................................................................................................. 28BASIC RATES TIME ................................................................................................................ 30EVENING RATE ....................................................................................................................... 32EARLY BIRD RATE .................................................................................................................. 35DATE/TIME ............................................................................................................................... 38RECEIPT HEADER ................................................................................................................... 40RESET REPORT # .................................................................................................................... 42CLEAR CODE HIST. ................................................................................................................ 43MAX ISSUERS ......................................................................................................................... 45MAX TELLERS......................................................................................................................... 47PARKING SITE ID# ................................................................................................................. 49RESET COUNTERS ................................................................................................................. 51FACTORY RESET .................................................................................................................... 52
Document #101-0150 3 7/18/08
This manual is designed to guide you through the programming of your Time Pass unit. Each menu screen isrepresented as a separate page. For further information, please contact Hamilton’s Technical Support Depart-ment at (800) 837-5561.
PREFACE
Document #101-0150 4 7/18/08
TIME PASS OVERVIEW
ACW G/L TO JUNCTIONBOX HARNESS(2 WIRE TWISTED PAIR SHEILDED)(48-3124)
COM 2
COM 3
COM 4
COM 1
TXRX
TXRX
TXRX
TXRX
FAULT DIAGON POWER
COM 0TXRX
TIMEPASS PAYSTATION MULTIPLEXER (49-9429)
JUNCTION BOX(49-9390)JUNCTION BOX(49-9390)
JUNCTION BOX(49-9390)
GROUND TO MUX
GROUND TO EARTHPRINTER CABLE(48-3122)
JUNCTION BOX(49-9390)
GROUND
MULTIPLEXER TO HANDHELD HARNESS(48-3126)
POWER CUBE
ACW G/L TO JUNCTIONBOX HARNESS(2 WIRE TWISTED PAIR SHEILDED)(48-3124)
ACW G/L TO JUNCTIONBOX HARNESS(2 WIRE TWISTED PAIR SHEILDED)(48-3124)
PRINTER(47-3120)
PRINTER CABLE(48-3122)
GROUND
MULTIPLEXER TO HANDHELD HARNESS(48-3126)
TIMEPASS PAYSTATION MULTIPLEXER (49-9429)
HANDHELD, AUDIT REMOTE(49-9428)
PASSTIME
AUTOCASHIER 1
AUTOCASHIER 2
ATTENDED STATION
TO BE SET UP IN ATTENDANTS STATION OR PLACE TIMEPASS MULTIPLEXER AND JUNCION BOX IN AUTOCASHIER
TICKET DISPENCER 1
TICKET DISPENCER 2
TICKET DISPENCER 3
PARKING
TIME
PASS
- GND+
SHEILD
Document #101-0150 5 7/18/08
TIME PASS WIRING SCHEMATIC
IF EIC
IS U
SED PL
UG 4 PO
SITIO
N INTO
POSIT
ION 17
IF EIC
IS N
OT USE
D PLUG 3
POSIT
ION IN
TO PO
SITIO
N 16
AND PL
UG EIC B
YPAS
S INTO
POSIT
ION10
10
INSI
DE A
CW
16
RED PO
SITIO
N 19
WHITE
POSIT
ION 18
GROUND U
NDER #1
0 NUT U
SED TO
HOLD TH
E DIST
IBUTIO
N WIRE
COVE
R
COMMUNICA
TION C
ABLE
17
+GN
D-
TIME PAS
S
TO B
E SET
UP
IN A
TTEN
DANT
S STA
TION
OR
PL
ACE T
IMEP
ASS M
ULTI
PLEX
ER A
ND
JUNC
ION
BOX
IN A
UTOC
ASHI
ER
TIM
EPA
SS
HAND
HELD
, AUD
IT R
EMOT
E(4
9-94
28)
TIM
EPAS
S PAY
STAT
ION
MUL
TIPL
EXER
(4
9-94
29)
MUL
TIPL
EXER
TO H
ANDH
ELD
HARN
ESS
(48-
3126
)
GROU
ND
PRIN
TER
CABL
E(4
8-31
22)
PRIN
TER
(47-
3120
)
POW
ER C
UBE
MUL
TIPL
EXER
TO
HAND
HELD
HAR
NESS
(48-
3126
)
GROU
ND
JUNC
TION
BOX
(49-
9390
)
PRIN
TER
CABL
E(4
8-31
22)
GROU
ND TO
EART
H
GROU
ND TO
MUX
JUNC
TION
BOX
(49-
9390
)
JUNC
TION
BOX
(49-
9390
)JU
NCTI
ON B
OX(4
9-93
90)
TIM
EPAS
S PAY
STAT
ION
MUL
TIPL
EXER
(4
9-94
29)
RXTXCO
M 0
POW
ERDI
AGON
FAUL
T
RXTXRXTX RXTXRXTX
COM
1
COM
4
COM
3
COM
2
ACW
G/L
TO JU
NCTI
ONBO
X HA
RNES
S(2
WIR
E TW
ISTE
D PA
IR SH
EILD
ED)
(48-
3124
)
SHEI
LD
49-9
426
SURG
E SUP
PRES
SOR
Document #101-0150 6 7/18/08
• The communication line between the GL-ACW and the Interface Box (Grey Box) is a two wiretwisted pair shielded cable (White and Red).
• Connect the red wire to the positive “+” side (#19) in the interface box and it MUST match up to#19 on the surge suppressor. The white wire will connect to the negative “-” side (#18) in theinterface box and it MUST match up to #18 on the surge suppressor. The shield must connect into#15 or GND in the interface box.
• The first Interface box only had one ground wire coming out of it. That ground wire should beattached to the Multiplexer. The second Interface box (shown above) has two grounds coming offthe box, one is for the Multiplexer (chassis ground) and the second is for earth ground.
INTERFACE BOX
+ GND-
GROUND TO EARTH
GROUND TO MUX
JUNCTION BOX(49-9390)JUNCTION BOX(49-9390)
SHEILD
Document #101-0150 7 7/18/08
• Hand-held will always be COM 0
• COM 1-4 cannot be changed (Preset)
• COM 1 = Not used, COM 2 = Printer, COM 3 = Not used and COM 4 = Interface box
TIME PASS WIRING SCHEMATIC
Document #101-0150 8 7/18/08
TIME PASS
• Upon initial system power up, the first screen will display:
HAMILTON MFGCODE REDEEM CENTER(C) 2004SOFTWARE V X.XX
• Next screen displays model and serial number.
MODEL MUXCSSERIAL NR. XXX(C) 2004
• Next screen displays the Login Menu.
LOGIN MENU1-3 SHIFT4 = MANAGER5 = MANAGER
• You will be entering from both the “F” function keys and numerical keys.
VERIFY CODES
LOGIN MENU1-3 SHIFT4 = MANAGER5 = INSTALLER
Document #101-0150 9 7/18/08
HAND-HELD
Document #101-0150 10 7/18/08
1-3 SHIFTSVERIFY CODES
LOGIN MENU1-3 SHIFT4 = MANAGER5 = INSTALLER
• To enter into the 1-3 Shifts press either 1, 2 or 3.
• Next screen displays:
F1 = VERIFY CODESF2 = EXIT
• To enter into verify codes press F1.
• Next screen displays:
REDEEM CODE MENUDATE: 06/23/04TIME: 13:59...-...-...
• You will enter in the 9 digit ticket code.
• When you enter in the last number it will automatically advance to the next screen.
• If the number you enter is a valid code, then the screen will display:
#1 TO PAY $ X.XXX DAYSX HOURSX MINUTES
• This information will be displayed on the Hand-held and printed out on the receipt. The codeentered will display the amount of money owed and how long they were there. Depending on lengthof stay, it will show in days, hours and minutes.
• If the code had already been used then the screen will display:
VALID CODEALREADY USED
• If the code is entered incorrectly then the screen displays:
INVALID CODE• Lines two and three will display a reason for why the code is invalid.
Document #101-0150 11 7/18/08
• When exiting from verifying code, press the back arrow twice and the next screen will display:
SHIFT REPORT ?
Y=YESN=NO
• By pressing “Y” for YES you will print out the shift report and then automatically advance to thenext screen.
PRINTING REPORT.
• When printing is complete the screen will automatically advance to the next screen.
• Next screen displays:
REPORT COPY?
Y=YESN=NO
• By pressing “Y” for YES will print out another copy of your shift report.
• Very Important *Printing a shift report will clear the shift data and reset the figures back tozero*.
• Next screen displays:
REPORT COPY?
Y=YESN=NO
• You must select “N” for NO to escape.
• Next screen displays:
LOGIN MENU1-3 SHIFT4 = MANAGER5 = INSTALLER
• When the initial request to print a report is prompted, selecting “NO” will not zero out your data.You will only clear data when you print the report. When pressing “NO” at initial prompt, the nextscreen displays:
LOGIN MENU1-3 SHIFT4 = MANAGER5 = INSTALLER
Document #101-0150 12 7/18/08
1-3 SHIFTSEXIT
LOGIN MENU1-3 SHIFT4 = MANAGER5 = INSTALLER
• To enter into the 1-3 Shifts, press 1, 2 or 3.
• Next screen displays:
F1 = VERIFY CODESF2 = EXIT
• If you want to exit the shift without verifying a code or just want to print out a shift report then pressF2 for exit.
• Next screen displays:
SHIFT REPORT ?Y=YESN=NO
• By pressing “Y” for YES you will print out the shift report and then automatically advance to thenext screen.
PRINTING REPORT.
• When printing is complete the screen will automatically advance to the next screen.
• Next screen displays:
REPORT COPY?
Y=YESN=NO
• By pressing “Y” for YES will print out another copy of your shift report.
• Very Important *Printing a shift report will clear the shift data and reset the figures back tozero*.
Document #101-0150 13 7/18/08
• Next screen displays:
REPORT COPY?
Y=YESN=NO
• You must select “N” for NO to escape.
• Next screen displays:
LOGIN MENU1-3 SHIFT4 = MANAGER5 = INSTALLER
• When the initial request to print a report is prompted, selecting “NO” will not zero out your data.You will only clear data when you print the report. When pressing “NO” at initial prompt, the nextscreen displays:
LOGIN MENU1-3 SHIFT4 = MANAGER5 = INSTALLER
Document #101-0150 14 7/18/08
MANAGER
FOOTER MESSAGE
LOGIN MENU1-3 SHIFT4 = MANAGER5 = INSTALLER
• To enter into Manager press 4.
• Next screen displays:
PASSWORD ....
• This screen is prompting you for a password, enter 1234. Once you enter the last digit it willautomatically advance to the next screen.
• Next screen displays:
F1 = GENERAL SETTINGSF2 = TIMEF3 = REPORTS
• To enter into General Settings press F1.
• Next screen displays:
F1 = FOOTER MESSAGEF2 = PASSWORD SETTINGS
• To enter into Footer Message press F1.
• Next screen displays:
THANK YOU
F1 = ACCEPTF2 = MODIFY
• If text is correct then press F1 to Accept.
• Next screen displays:
COME AGAIN
F1 = ACCEPTF2 = MODIFY
Document #101-0150 15 7/18/08
• If text is correct then press F1 to Accept.
• Next screen displays:
F1 = FOOTER MESSAGEF2 = PASSWORD SETTING
• If either line is incorrect or you wish to change the text press F2 to modify.
• CAUTION: Pressing F2 will clear the text.
• Next screen displays:
............................F1 = ENTER TEXT MODEF2 = UPPER/LOWER/SPEC.F3 = SCROLL-UP F4 = DOWN
• Once text is entered, press the right arrow to save.
• To input text, see the example on the following page.
• Press the back arrow or “ESC” button three times to return to the Login Menu.
• When going back to the main menu as a manager you will be prompted to print a shift report, pleaserefer to the shift report section in 1-3 Shifts for procedure.
Document #101-0150 16 7/18/08
EXAMPLE
Press F1 an “A” will appear in the first spotA _ _ _ _ _ _ _ _ _ _ _Using the F2 button will allow you to scroll from upper case to lower case to spec.Using the F3 button will allow you to scroll up the alphabet.Using the F4 button will allow you to scroll down the alphabet.
Press the F3 button to desired letter, digit or symbol.T_ _ _ _ _ _ _ _ _ _ _ _
Next by pressing the F1 button will place an “A” in the next spaceTA _ _ _ _ _ _ _ _ _ _ _Using the F2 button will allow you to scroll from upper case to lower case to spec.Using the F3 button will allow you to scroll up the alphabet.Using the F4 button will allow you to scroll down the alphabet.Using the F1 button will allow you to move to the next space
Next by pressing the F1 button will place an “A” in the next space.THA_ _ _ _ _ _ _ _ _ _ _Using the F2 button will allow you to scroll from upper case to lower case to spec.Using the F3 button will allow you to scroll up the alphabet.Using the F4 button will allow you to scroll down the alphabet.Using the F1 button will allow you to move to the next space.
Next by pressing the F1 button will place an “A” in the next space.THAA_ _ _ _ _ _ _ _ _ _
Using the F2 button will allow you to scroll from upper case to lower case to spec.Using the F3 button will allow you to scroll up the alphabet.Using the F4 button will allow you to scroll down the alphabet.Using the F1 button will allow you to move to the next space.
Next by pressing the F1 button will place an “A” in the next space.THANA_ _ _ _ _ _ __ _Using the F2 button will allow you to scroll from upper case to lower case to spec.Using the F3 button will allow you to scroll up the alphabet.Using the F4 button will allow you to scroll down the alphabet.Using the F1 button will allow you to move to the next space.Next by pressing the F1 button will place an “A” in the next space.THANKA_ _ _ _ _ _ _ _ _
Using the F2 button will allow you to scroll from upper case to lower case to spec.Using the F3 button will allow you to scroll up the alphabet.
Document #101-0150 17 7/18/08
Using the F4 button will allow you to scroll down the alphabet.Using the F1 button will allow you to move to the next space.Next by pressing the F1 button will place an “A” in the next space.THANK A_ _ _ _ _ _ _ _Using the F2 button will allow you to scroll from upper case to lower case to spec.Using the F3 button will allow you to scroll up the alphabet.Using the F4 button will allow you to scroll down the alphabet.Using the F1 button will allow you to move to the next space.Next by pressing the F1 button will place an “A” in the next space.THANK YA_ _ _ __ _ _ _ _
Using the F2 button will allow you to scroll from upper case to lower case to spec.Using the F3 button will allow you to scroll up the alphabet.Using the F4 button will allow you to scroll down the alphabet.Using the F1 button will allow you to move to the next space.Next by pressing the F1 button will place an “A” in the next space.THANK YOA_ _ _ _ _ _ _
Using the F2 button will allow you to scroll from upper case to lower case to spec.Using the F3 button will allow you to scroll up the alphabet.Using the F4 button will allow you to scroll down the alphabet.Using the F1 button will allow you to move to the next space.Next by pressing the F1 button will place an “A” in the next space.THANK YOU_ _ _ _ _ _ _
Using the F2 button will allow you to scroll from upper case to lower case to spec.Using the F3 button will allow you to scroll up the alphabet.Using the F4 button will allow you to scroll down the alphabet.Using the F1 button will allow you to move to the next space.Once text is complete then press the right —> to save.
Document #101-0150 18 7/18/08
MANAGERPASSWORD SETTING
LOGIN MENU1-3 SHIFT4 = MANAGER5 = INSTALLER
• To enter into Manager press 4.
• Next screen displays:
PASSWORD ....
• This screen is prompting you for a password, enter 1234. Once you enter the last digit it willautomatically advance to the next screen.
• Next screen displays:
F1 = GENERAL SETTINGSF2 = TIMEF3 = REPORTS
• To enter into General Settings press F1.
• Next screen displays:
F1 = FOOTER MESSAGEF2 = PASSWORD SETTING
• To enter into Password Setting press F2.
• Next screen displays:
F1 = SHIFT 1F2 = SHIFT 2F3 = SHIFT 3F4 = MANAGER
• The manager has the ability to set passwords to protect the settings and data of the system.
• To view the password for Shift 1 press F1.
• Next screen displays:
PASSWORD 0
F1 = ACCEPTF2 = MODIFY
Document #101-0150 19 7/18/08
• If password is correct then press F1.
• Next screen displays:
F1 = SHIFT 1F2 = SHIFT 2F3 = SHIFT 3F4 = MANAGER
• If password is incorrect then press F2 to modify.
• Next screen displays:
PASSWORD . . . . . . .
PRESS <— TO CORRECTPRESS —> TO ACCEPT
• Enter in a password up to 4 digits long. Make sure that it is a unique password. You may want towrite them down and store them in a secure place.
• Once the last digit is entered the screen will automatically advance to the next screen.
• Next screen displays:
F1 = SHIFT 1F2 = SHIFT 2F3 = SHIFT 3F4 = MANAGER
• To view or change Shift 2 , Shift 3 or Manager follow the steps above.
• Press the back arrow 4 times to return to the Login Menu.
• When going back to the main menu as a manager you will be prompted to print a shift report, pleaserefer to the shift report section in 1-3 Shifts for procedure.
Document #101-0150 20 7/18/08
MANAGER
DISPLAY CLOCK
LOGIN MENU1-3 SHIFT4 = MANAGER5 = INSTALLER
• To enter into Manager press 4.
• Next screen displays:
PASSWORD ....
• This screen is prompting you for a password, enter 1234. Once you enter the last digit it willautomatically advance to the next screen.
• Next screen displays:
F1 = GENERAL SETTINGSF2 = TIMEF3 = REPORTS
• To enter into Time press F2.
• Next screen displays:
F1 = DISPLAY CLOCKF2 = CHANGE TIME
• To display clock press F1. Please note that this is a view only screen.
• Next screen displays:
CLOCK SETTINGSDATE: 06/25/04TIME: 11:13
• Press the back arrow or “ESC” button 4 times to return to the Login Menu.
• When going back to the main menu as a manager you will be prompted to print a shift report, pleaserefer to the shift report section in 1-3 Shifts for procedure.
Document #101-0150 21 7/18/08
MANAGER
CHANGE TIME
LOGIN MENU1-3 SHIFT4 = MANAGER5 = INSTALLER
• To enter into Manager press 4.
• Next screen displays:
PASSWORD ....
• This screen is prompting you for a password, enter 1234. Once you enter the last digit it willautomatically advance to the next screen.
• Next screen displays:
F1 = GENERAL SETTINGSF2 = TIMEF3 = REPORTS
• To enter into Time press F2.
• Next screen displays:
F1 = DISPLAY CLOCKF2 = CHANGE TIME
• To enter into Change Time press F2.
• Next screen displays:
ENTER TIME ..-..
• The time must be entered in Military time.
• Once the last number is entered the screen will automatically advance to the next screen.
• Next screen displays:
F1 = DISPLAY CLOCKF2 = CHANGE TIME
• Press the back arrow or “ESC” button 3 times to return to the Login Menu.
• When going back to the main menu as a manager you will be prompted to print a shift report, pleaserefer to the shift report section in 1-3 Shifts for procedure.
Document #101-0150 22 7/18/08
MANAGER
PERIOD REPORT
LOGIN MENU1-3 SHIFT4 = MANAGER5 = INSTALLER
• To enter into Manager press 4.
• Next screen displays:
PASSWORD ....
• This screen is prompting you for a password, enter 1234. Once you enter the last digit it willautomatically advance to the next screen.
• Next screen displays:
F1 = GENERAL SETTINGSF2 = TIMEF3 = REPORTS
• To enter into Reports press F3.
• Next screen displays:
F1 = PERIOD REPORTF2 = DISP. MAN REPORTF3 = DISP. ACW REPORT
• To enter into Period Report press F1.
• Next screen displays:
FR MMDD ../..
• Enter the starting Month and Date for the data you wish to retrieve.
• Once last number is entered the screen will automatically advance to the next screen.
• Next screen displays:
TO MMDD ../..
Document #101-0150 23 7/18/08
• Enter the starting Month and Date for the data you wish to retrieve.
• Once the last number is entered, the report will begin printing. After it has printed it will prompt youto print another copy. If you would like a second copy press “Y” or if you do not want anothercopy then press “N”.
• Next screen displays:
F1 = GENERAL SETTINGSF2 = TIMEF3 = REPORTS
• Press the back arrow or “ESC” button twice to return to the Login Menu.
• When going back to the main menu as a manager you will be prompted to print a shift report, pleaserefer to the shift report section in 1-3 Shifts for procedure.
Document #101-0150 24 7/18/08
MANAGER
DISP. MAN REPORT
LOGIN MENU1-3 SHIFT4 = MANAGER5 = INSTALLER
• To enter into Manager press 4.
• Next screen displays:
PASSWORD ....
• This screen is prompting you for a password, enter 1234. Once you enter the last digit it willautomatically advance to the next screen.
• Next screen displays:
F1 = GENERAL SETTINGSF2 = TIMEF3 = REPORTS
• To enter into Reports press F3.
• Next screen displays:
F1 = PERIOD REPORTF2 = DISP. MAN REPORTF3 = DISP. ACW REPORT
• To enter into Disp. Man Report press F2.
• Next screen displays:
FR MMDD ../..
• Enter the starting Month and Date for the data you wish to retrieve.
• Once last number is entered the screen will automatically advance to the next screen.
• Next screen displays:
TOTAL COUNTERS XSALES —> XTIME ——> XCARS ——> X
Document #101-0150 25 7/18/08
• The “Sales,” “Time” and “Cars” are a one day total based on the date that you enter in “FRMMDD.”
• Sales will be in cents (example 800 = 8 dollars).
• Time will be in minutes.
• Cars will increase by 1 every time one uses the manual lane.
• Press the back arrow or “ESC” button three times to return to the Login Menu.
• When going back to the main menu as a manager you will be prompted to print a shift report, pleaserefer to the shift report section in 1-3 Shifts for procedure.
Document #101-0150 26 7/18/08
MANAGER
DISP. ACW REPORT
LOGIN MENU1-3 SHIFT4 = MANAGER5 = INSTALLER
• To enter into Manager press 4.
• Next screen displays:
PASSWORD ....
• This screen is prompting you for a password, enter 1234. Once you enter the last digit it willautomatically advance to the next screen.
• Next screen displays:
F1 = GENERAL SETTINGSF2 = TIMEF3 = REPORTS
• To enter into Reports press F3.
• Next screen displays:
F1 = PERIOD REPORTF2 = DISP. MAN REPORTF3 = DISP. ACW REPORT
• To enter into Disp. ACW Report press F3.
• Next screen displays:
FR MMDD ../..
• Enter the starting Month and Date for the data you wish to retrieve.
• Once last number is entered the screen will automatically advance to the next screen.
• Next screen displays:
TOTAL COUNTERS XSALES —> XTIME ——> XCARS ——> X
Document #101-0150 27 7/18/08
• The “Sales,” “Time” and “Cars” are a one day total based on the date that you enter in “FRMMDD.”
• Sales will be in cents (example 800 = 8 dollars).
• Time will be in minutes.
• Cars will increase by 1 every time one uses the Autocashier.
• Press the back arrow or “ESC” button three times to return to the Login Menu.
• When going back to the main menu as a manager you will be prompted to print a shift report, pleaserefer to the shift report section in 1-3 Shifts for procedure.
Document #101-0150 28 7/18/08
INSTALLER
BASIC RATES $$$
LOGIN MENU1-3 SHIFT4 = MANAGER5 = INSTALLER
• To enter into Installer press 5.
• Next screen displays:
PASSWORD ....
• This screen is prompting you for a password, enter 0108. Once you enter the last digit it willautomatically advance to the next screen.
• Next screen displays:
F1 = RATE STRUCTUREF2 = DATE/TIMEF3 = DATABASE FUNCTIONF4 = FACTORY SETUP
• To enter into Rate Structure press F1.
• Next screen displays:
F1 = BASIC RATES $$$F2= BASIC RATES TIMEF3 = EVENING RATESF4 = EARLY BIRD RATE
• To enter into Basic Rates $$$ press F1.
• Next screen displays:
F1=$ 1.00 15MINF2=$ 2.00 30MINF3=$ 3.00 45MINF4=$ 4.00 60MIN
• You have up to 26 dollar rates.
• You have 1 daily dollar rate.
• You have 1 weekly dollar rate.
• To change a dollar rate press the “F” button of the rate you wish to change.
• Press F1 to change rate.
Document #101-0150 29 7/18/08
• Next screen displays:
PRICE: $1.00
F1=ACCEPTF2=MODIFY
• If price is correct then press F1 to accept.
• Next screen displays:
F1=$ 1.00 15MINF2=$ 2.00 30MINF3=$ 3.00 45MINF4=$ 4.00 60MIN
• If price is incorrect press F2 for modify.
• Next screen displays:
PRICE: .......
PRESS <— TO CORRECTPRESS —> TO ACCEPT
• Enter in the value of the price in cents (example 100 = 1.00).
• When entering an amount up to four digits, press the right arrow key to accept. If a five digit numberis entered, the screen will automatically advance to the next.
• Next screen displays:
F1=$ 1.00 15MINF2=$ 2.00 30MINF3=$ 3.00 45MINF4=$ 4.00 60MIN
• To change any other rate follow the steps above.
• Once you have changed your rates press “ESC.”
• Next screen displays:
F1 = BASIC RATES $$$F2 = BASIC RATES TIMEF3 = EVENING RATESF4 = EARLY BIRD RATE
• Press the back arrow or “ESC” button twice to return to the Login Menu.
Document #101-0150 30 7/18/08
INSTALLER
BASIC RATES TIME
LOGIN MENU1-3 SHIFT4 = MANAGER5 = INSTALLER
• To enter into Installer press 5.
• Next screen displays:
PASSWORD ....
• This screen is prompting you for a password, enter 0108. Once you enter the last digit it willautomatically advance to the next screen.
• Next screen displays:
F1 = RATE STRUCTUREF2 = DATE/TIMEF3 = DATABASE FUNCTIONF4 = FACTORY SETUP
• To enter into Rate Structure press F1.
• Next screen displays:
F1 = BASIC RATES $$$F2= BASIC RATES TIMEF3 = EVENING RATESF4 = EARLY BIRD RATE
• To enter into Basic Rates Times press F2.
• Next screen displays:
F1=$ 1.00 15MINF2=$ 2.00 30MINF3=$ 3.00 45MINF4=$ 4.00 60MIN
• You have up to 26 hourly rates of time.
• You have 1 daily rate of time.
• You have 1 weekly rate of time.
• To change a time rate press the “F” button of the rate you wish to change.
• Press F1 to change rate.
Document #101-0150 31 7/18/08
• Next screen displays:
15 MINUTES
F1 = ACCEPTF2 = MODIFY
• If time is correct then press F1 to accept.
• Next screen displays:
F1=$ 1.00 15MINF2=$ 2.00 30MINF3=$ 3.00 45MINF4=$ 4.00 60MIN
• If price is incorrect press F2 for modify.
• Next screen displays:
........... MINUTES
PRESS <— TO CORRECTPRESS —> TO ACCEPT
• Enter the value of the time in minutes (example 120 = 2 hours). The maximum number of minutesyou can input is 1440 minutes, which will automatically change it to a daily rate (1439 minutes =23.98 hours).
• When entering an amount up to three digits amount you will have to press the right arrow key toaccept. If a four digit number is entered, the screen will automatically advance to the next.
• Next screen displays:
F1=$ 1.00 15MINF2=$ 2.00 30MINF3=$ 3.00 45MINF4=$ 4.00 60MIN
• To change any other time rate follow the steps above.
• Once you have changed your time rates press “ESC.”
• Next screen displays:
F1 = BASIC RATES $$$F2 = BASIC RATES TIMEF3 = EVENING RATESF4 = EARLY BIRD RATE
• Press the back arrow or “ESC” button twice to return to the Login Menu.
Document #101-0150 32 7/18/08
INSTALLER
EVENING RATE
LOGIN MENU1-3 SHIFT4 = MANAGER5 = INSTALLER
• To enter into Installer press 5.
• Next screen displays:
PASSWORD ....
• This screen is prompting you for a password, enter 0108. Once you enter the last digit it willautomatically advance to the next screen.
• Next screen displays:
F1 = RATE STRUCTUREF2 = DATE/TIMEF3 = DATABASE FUNCTIONF4 = FACTORY SETUP
• To enter into Rate Structure press F1.
• Next screen displays:
F1 = BASIC RATES $$$F2= BASIC RATES TIMEF3 = EVENING RATESF4 = EARLY BIRD RATE
• To enter into Evening Rates press F3.
• Next screen displays:
F1 EV. VALUE = $ .00F2 EV. START = 00:00F3 EV. STOP = 00:00MAKE SELECTION
• You can enter in a flat rate for the evening in this category.
• You will also set the start time for the evening rate.
• You will also set the stop time for the evening rate.
• To enter or change the Evening value amount press F1.
Document #101-0150 33 7/18/08
• Next screen displays:
F1 EV. VALUE = .......PRESS <— TO CORRECTPRESS —> TO ACCEPT
• Enter the dollar rate in cents (example 100 = $1.00).
• When entering an amount up to three digits amount you will have to press the right arrow key toaccept. If a four digit number is entered, the screen will automatically advance to the next.
• Next screen displays:
F1 EV. VALUE = $ 5.00F2 EV. START = 00:00F3 EV. STOP = 00:00MAKE SELECTION
• Set the start time of your evening rate by pressing F2.
• Next screen displays:
F1 EV. VALUE = $ 5.00F2 EV. START = ..:..F3 EV. STOP = 00:00MAKE SELECTION
• Enter the time when you want the evening rate to start. Use military time (Example 7:00 PM =19:00PM)
• Once the last number is entered, the screen will automatically advance to the next screen.
• Next screen displays:
F1 EV. VALUE = $ 5.00F2 EV. START = 19:00F3 EV. STOP = 00:00MAKE SELECTION
• Set the stop time of your evening rate by pressing F3.
• Next screen displays:
F1 EV. VALUE = $ 5.00F2 EV. START = 19:00F3 EV. STOP = ..:..MAKE SELECTION
• Enter the time when you want the evening rate to stop. Use military time (Example 11:00 PM =23:00PM)
• Once the last number is entered, the screen will automatically advance to the next screen.
Document #101-0150 34 7/18/08
• Next screen displays:
F1 EV. VALUE = $ 5.00F2 EV. START = 19:00F3 EV. STOP = 23:00MAKE SELECTION
• Once you have set the Time and Rates, press the back arrow or “ESC” once.
• Next screen displays:
F1 = BASIC RATES $$$F2= BASIC RATES TIMEF3 = EVENING RATESF4 = EARLY BIRD RATE
• Press the back arrow or “ESC” button twice to return to the Login Menu.
Document #101-0150 35 7/18/08
INSTALLER
EARLY BIRD RATE
LOGIN MENU1-3 SHIFT4 = MANAGER5 = INSTALLER
• To enter into Installer press 5.
• Next screen displays:
PASSWORD ....
• This screen is prompting you for a password, enter 0108. Once you enter the last digit it willautomatically advance to the next screen.
• Next screen displays:
F1 = RATE STRUCTUREF2 = DATE/TIMEF3 = DATABASE FUNCTIONF4 = FACTORY SETUP
• To enter into Rate Structure press F1.
• Next screen displays:
F1 = BASIC RATES $$$F2= BASIC RATES TIMEF3 = EVENING RATESF4 = EARLY BIRD RATE
• To enter into Early Bird Rate press F4.
• Next screen displays:
F1 EB. START = 00:00F2 EB. STOP = 00:00F3 MIN VALUE = $ .00F4 DISCOUNT = $ .00
• You can enter the start time for the Early Bird Rate.
• You can enter the stop time for the Early Bird Rate.
• You will also set the Min Value which is the lowest amount charged before you will get a discount.
• You will also set the Discount which is the maximum discount allowed for the early bird rate.
• To enter EB Start Time press F1.
Document #101-0150 36 7/18/08
• Next screen displays:
F1 EB. START = ..:..F2 EB. STOP = 00:00F3 MIN VALUE = $ .00F4 DISCOUNT = $ .00
• Enter the time you want the Early Bird rate to start. (Example 08:00)
• Once the last number is entered the screen will automatically advance to the next screen.
• Next screen displays:
F1 EB. START = 08:00F2 EB. STOP = 00:00F3 MIN VALUE = $ .00F4 DISCOUNT = $ .00
• To enter EB Stop Time press F2.
• Next screen displays:
F1 EB. START = 08:00F2 EB. STOP = ..:..F3 MIN VALUE = $ .00F4 DISCOUNT = $ .00
• Enter the time you want the Early Bird rate to stop. (Example 10:00)
• Once last number is enter the screen will automatically advance to the next screen.
• Next screen displays:
F1 EB. START = 08:00F2 EB. STOP = 10:00F3 MIN VALUE = $ .00F4 DISCOUNT = $ .00
• To enter in the Min Val press F3.
• Next screen displays:
F1 EB. START = 08:00F2 EB. STOP = 10:00F3 MIN VALUE = $ ....PRESS —> TO ACCEPT
• Enter in the amount in cents (example 0300 = $3.00).
• Once last number is enter the screen will automatically advance to the next screen.
Document #101-0150 37 7/18/08
• Next screen displays:
F1 EB. START = 08:00F2 EB. STOP = 10:00F3 MIN VALUE = $ 3.00F4 DISCOUNT = $ .00
• To enter in to Discount press F4
• Next screen displays:
F1 EB. START = 08:00F2 EB. STOP = 10:00F3 MIN VALUE = $ 3.00F4 DISCOUNT = $ ....
• Enter amount in cents (example 050 =$0.50).
• When entering an amount up to three digits amount you will have to press the right arrow key toaccept. If a four digit number is entered, the screen will automatically advance to the next.
• Next screen displays:
F1 EB. START = 08:00F2 EB. STOP = 10:00F3 MIN VALUE = $ 3.00F4 DISCOUNT = $ .50
• Press the back arrow or “ESC” button three times to return to the Login Menu.
Document #101-0150 38 7/18/08
INSTALLER
DATE/TIME
LOGIN MENU1-3 SHIFT4 = MANAGER5 = INSTALLER
• To enter into Installer press 5.
• Next screen displays:
PASSWORD ....
• This screen is prompting you for a password, enter 0108. Once you enter the last digit it willautomatically advance to the next screen.
• Next screen displays:
F1 = RATE STRUCTUREF2 = DATE/TIMEF3 = DATABASE FUNCTIONF4 = FACTORY SETUP
• To enter into Date/Time press F2.
• Next screen displays:
F1 = DISPLAY CLOCKF2 = CHANGE TIMEF3 = CHANGE DATE
• You will be able to Display the clock.
• You will be able Change the time.
• You will be able to Change the date.
• To display the clock press F1.
• Next screen displays:
CLOCK SETTINGSDATE: 07/02/04TIME: 14:27
• Press the Back arrow or “ESC” button once to return to previous screen.
Document #101-0150 39 7/18/08
• Next screen displays:
F1 = DISPLAY CLOCKF2 = CHANGE TIMEF3 = CHANGE DATE
• To change the time press F2.
• Next screen displays:
ENTER TIME ..:..
• Enter the time in military time (example 1:00 PM = 13:00).
• Once the last number is entered the screen will automatically advance to the next screen.
• Next screen displays:
F1 = DISPLAY CLOCKF2 = CHANGE TIMEF3 = CHANGE DATE
• To change the Date press F3.
• Next screen displays:
MMDDYY ../../..
• Enter the two digit month, two digit day and two digit year.
• Once the last number is entered the screen will automatically advance to the next screen.
• Next screen displays:
F1 = DISPLAY CLOCKF2 = CHANGE TIMEF3 = CHANGE DATE
• Press the back arrow or “ESC” button twice to return to the Login Menu.
Document #101-0150 40 7/18/08
INSTALLER
RECEIPT HEADER
LOGIN MENU1-3 SHIFT4 = MANAGER5 = INSTALLER
• To enter into Installer press 5.
• Next screen displays:
PASSWORD ....
• This screen is prompting you for a password, enter 0108. Once you enter the last digit it willautomatically advance to the next screen.
• Next screen displays:
F1 = RATE STRUCTUREF2 = DATE/TIMEF3 = DATABASE FUNCTIONF4 = FACTORY SETUP
• To enter into Database Function press F3.
• Next screen displays:
F1 = RECEIPT HEADERF2 = RESET REPORT #F3 = CODE GENERATORF4 = RESET COUNTERS
• To enter into Receipt Header press F1.
• Next screen displays:
SELECT ITEM 1-6
• You will have up to six lines of text for your receipt header.
• To proceed to line 1 press 1.
Document #101-0150 41 7/18/08
• Next screen displays:
HAMILTON SYS III
F1 = ACCEPTF2 = MODIFY
• If text is correct press F1 to accept.
• Next screen displays:
SELECT ITEM 1-6
• If text is incorrect press F2 to modify.
• Next screen displays:
....................................................F1 = ENTER TEXT MODEF2 = UPPER/LOWER/SPEC.F3 = SCROLL-UP F4 = DOWN
• To program see example in Manager Footer Message section.
• Next screen displays:
SELECT ITEM 1-6
• To program items 2-6 follow the above steps.
• Press the back arrow or “ESC” button twice to return to the Login Menu.
Document #101-0150 42 7/18/08
INSTALLER
RESET REPORT #
LOGIN MENU1-3 SHIFT4 = MANAGER5 = INSTALLER
• To enter into Installer press 5.
• Next screen displays:
PASSWORD ....
• This screen is prompting you for a password, enter 0108. Once you enter the last digit it willautomatically advance to the next screen.
• Next screen displays:
F1 = RATE STRUCTUREF2 = DATE/TIMEF3 = DATABASE FUNCTIONF4 = FACTORY SETUP
• To enter into Database Function press F3.
• Next screen displays:
F1 = RECEIPT HEADERF2 = RESET REPORT #F3 = CODE GENERATORF4 = RESET COUNTERS
• To Reset Report # press F2.
• Once you press F2 the Report # will automatically reset itself back to zero.
• Next screen displays:
F1 = RATE STRUCTUREF2 = DATE/TIMEF3 = DATABASE FUNCTIONF4 = FACTORY SETUP
• Press the back arrow or “ESC” button once to return to the Login Menu.
Document #101-0150 43 7/18/08
INSTALLER
CLEAR CODE HIST.
LOGIN MENU1-3 SHIFT4 = MANAGER5 = INSTALLER
• To enter into Installer press 5.
• Next screen displays:
PASSWORD ....
• This screen is prompting you for a password, enter 0108. Once you enter the last digit it willautomatically advance to the next screen.
• Next screen displays:
F1 = RATE STRUCTUREF2 = DATE/TIMEF3 = DATABASE FUNCTIONF4 = FACTORY SETUP
• To enter into Database Function press F3.
• Next screen displays:
F1 = RECEIPT HEADERF2 = RESET REPORT #F3 = CODE GENERATORF4 = RESET COUNTERS
• To enter into Code Generator press F3.
• Next screen displays:
F1 = CLEAR CODE HISTORYF2 = MAX ISSUERSF3 = MAX TELLERSF4 = PARKING SITE ID
• To enter into Clear Code History press F1.
Document #101-0150 44 7/18/08
• Next screen displays:
F1 = ERASE CODEHISTORY TABLES
• By pressing F1 you will erase your code history.
• Next screen displays:
ERASING CODEHISTORY TABLES
• Once the process is complete the screen will automatically advance to next screen.
• Next screen displays:
F1 = CLEAR CODE HIST.F2 = MAX ISSUERSF3 = MAX TELLERSF4 = PARKING SITE ID#
• Pressing the back arrow or “ESC” button twice to return to the Login Menu.
Document #101-0150 45 7/18/08
INSTALLER
MAX ISSUERS
LOGIN MENU1-3 SHIFT4 = MANAGER5 = INSTALLER
• To enter into Installer press 5.
• Next screen displays:
PASSWORD ....
• This screen is prompting you for a password, enter 0108. Once you enter the last digit it willautomatically advance to the next screen.
• Next screen displays:
F1 = RATE STRUCTUREF2 = DATE/TIMEF3 = DATABASE FUNCTIONF4 = FACTORY SETUP
• To enter into Database Function press F3.
• Next screen displays:
F1 = RECEIPT HEADERF2 = RESET REPORT #F3 = CODE GENERATORF4 = RESET COUNTERS
• To enter into Code Generator press F3.
• Next screen displays:
F1 = CLEAR CODE HIST.F2 = MAX ISSUERSF3 = MAX TELLERSF4 = PARKING SITE ID
• To enter into Max Issuers press F2.
Document #101-0150 46 7/18/08
• Next screen displays:
MAX ISSUERS 1
F1 = ACCEPTF2 = MODIFY
• This will allow you to set the number of ticket dispensers you have on your network.
• If the text is correct press F1 to accept.
• Next screen displays:
F1 = CLEAR CODE HIST.F2 = MAX ISSUERSF3 = MAX TELLERSF4 = PARKING SITE ID#
• If text was incorrect press F2 to modify.
• Next screen displays:
MAX ISSUES .
PRESS <— TO CORRECTPRESS —> TO ACCEPT
• Enter a number from 1 to 8.
• Note: Entering a 0 it will automatically default to a 1. Entering a 9 will automatically default to 8.
• Once you enter the number, the screen will automatically advance to the next.
• Next screen displays:F1 = CLEAR CODE HIST.F2 = MAX ISSUERSF3 = MAX TELLERSF4 = PARKING SITE ID#
• Press the back arrow or “ESC” button twice to return to the Login Menu.
Document #101-0150 47 7/18/08
INSTALLER
MAX TELLERS
LOGIN MENU1-3 SHIFT4 = MANAGER5 = INSTALLER
• To enter into Installer press 5.
• Next screen displays:
PASSWORD ....
• This screen is prompting you for a password, enter 0108. Once you enter the last digit it willautomatically advance to the next screen.
• Next screen displays:
F1 = RATE STRUCTUREF2 = DATE/TIMEF3 = DATABASE FUNCTIONF4 = FACTORY SETUP
• To enter into Database Function press F3.
• Next screen displays:
F1 = RECEIPT HEADERF2 = RESET REPORT #F3 = CODE GENERATORF4 = RESET COUNTERS
• To enter into Code Generator press F3.
• Next screen displays:
F1 = CLEAR CODE HISTORYF2 = MAX ISSUERSF3 = MAX TELLERSF4 = PARKING SITE ID #
• To enter into Max Tellers press F3.
Document #101-0150 48 7/18/08
• Next screen displays:
MAX TELLERS 1
F1 = ACCEPTF2 = MODIFY
• This will allow you to set the number of Tellers (ACW’s) you have on your network.
• If the text is correct press F1 to accept.
• Next screen displays:
F1 = CLEAR CODE HIST.F2 = MAX ISSUERSF3 = MAX TELLERSF4 = PARKING SITE ID#
• If text was incorrect press F2 to modify.
• Next screen displays:
MAX TELLERS .
PRESS <— TO CORRECTPRESS —> TO ACCEPT
• Enter in a number from 1 to 8.
• Note: Entering a 0 it will automatically default to a 1. Entering a 9 will automatically default to 8.
• Once you enter the number, the screen will automatically advance to the next.
• Next screen displays:
F1 = CLEAR CODE HIST.F2 = MAX ISSUERSF3 = MAX TELLERSF4 = PARKING SITE ID#
• Press the back arrow or “ESC” button twice to return to the Login Menu.
Document #101-0150 49 7/18/08
INSTALLER
PARKING SITE ID#
LOGIN MENU1-3 SHIFT4 = MANAGER5 = INSTALLER
• To enter into Installer press 5.
• Next screen displays:
PASSWORD ....
• This screen is prompting you for a password, enter 0108. Once you enter the last digit it willautomatically advance to the next screen.
• Next screen displays:
F1 = RATE STRUCTUREF2 = DATE/TIMEF3 = DATABASE FUNCTIONF4 = FACTORY SETUP
• To enter into Database Function press F3.
• Next screen displays:
F1 = RECEIPT HEADERF2 = RESET REPORT #F3 = CODE GENERATORF4 = RESET COUNTERS
• To enter into Code Generator press F3.
• Next screen displays:
F1 = CLEAR CODE HISTORYF2 = MAX ISSUERSF3 = MAX TELLERSF4 = PARKING SITE ID #
• To enter into Parking Site ID# press F4.
Document #101-0150 50 7/18/08
• Next screen displays:
PARKING CODE # 1234
F1 = ACCEPTF2 = MODIY
• The Parking Code is a unique code that links your Tellers and the Issuers. What is set in this cat-egory will have to match the same in the Issuers.
• If the text is correct then press F1 to accept.
• Next screen displays:
F1 = CLEAR CODE HIST.F2 = MAX ISSUERSF3 = MAX TELLERSF4 = PARKING SITE ID#
• If text is incorrect then press F2 to modify.
• Next screen displays:
PARKING CODE # ......
PRESS <— TO CORRECTPRESS —> TO ACCEPT
• The code should be at least four digits long and unique.
• When entering an amount up to four digits, press the right arrow key to accept. If a five digit numberis entered, the screen will automatically advance to the next.
• Next screen displays:
F1 = CLEAR CODE HIST.F2 = MAX ISSUERSF3 = MAX TELLERSF4 = PARKING SITE ID#
• Press the back arrow or “ESC” button twice to return to the Login Menu.
Document #101-0150 51 7/18/08
INSTALLER
RESET COUNTERS
• Not applicable.
• Press the back arrow or “ESC” button once to return to the Login Menu.
Document #101-0150 52 7/18/08
INSTALLER
FACTORY RESET
• This setting is only used for the factory (Hamilton Manufacturing Corp.)
Document #101-0150 53 7/18/08
(See next page for additional provisions)
LIMITED WARRANTY AGREEMENTOF HAMILTON MANUFACTURING CORP.
Hamilton Manufacturing Corp., an Ohio Corporation, (“Seller”) warrants to Purchaser that all newequipment shall be free from defects in material and factory workmanship for a period of one (1) year from theoriginal shipping date. Hamilton Manufacturing Corp. further warrants if any part of said new equipment inSeller’s sole opinion, requires replacement or repair due to a defect in material or factory workmanship duringsaid period, Seller will repair or replace said new equipment. Purchaser’s remedies and the liabilities andobligations of Seller herein shall be limited to repair or replacement of the equipment as Seller may choose, andSeller’s obligation to remedy such defects shall not exceed the Purchaser’s original cost for the equipment.Purchaser EXPRESSLY AGREES this is the EXCLUSIVE REMEDY under this warranty. There are no otherexpress or implied warranties which extend beyond the face hereof. All warranty repair service must beperformed by either a Factory Trained Service Representative or HAMILTON MANUFACTURINGCORP., 1026 Hamilton Drive, Holland, Ohio 43528 PHONE (419) 867-4858 or (800) 837-5561, FAX(419) 867-4867.
The limited warranty for new equipment is conditioned upon the following:
1. The subject equipment has not, in the Seller’s sole opinion, been subjectedto: accident, abuse, misuse, vandalism, civil disobedience, riots, acts ofGod, natural disaster, acts of war or terrorism.
2. The Seller shall not be liable for any expense incurred by Purchaser inci-dental to the repair or replacement of equipment and Purchaser shallassume full responsibility for any freight or shipping charges.
3. The coverage of this warranty shall not extend to expendable parts.4. Purchaser shall have a warranty registration card on file with Seller prior to
any claim in order for warranty protection to apply.5. No warranty coverage is applicable to any equipment used for currency
other than that specified at the time of the purchase.6. Seller expressly disclaims any warranty that counterfeit currency will not
activate said equipment.7. Seller expressly disclaims any warranty for any losses due to bill manipula-
tion or theft or loss of cash under any circumstances.8. Use of the equipment for anything other than its intended and designed use
will void the Limited Warranty Agreement. Use of equipment for anythingother than its intended and designed use includes, but is not limited to,downloading software/applications not certified by Seller such as e-mail,spyware, screen savers, viruses, worms, third party software, web searchengines, cookies, spam, desktop applications, games, web surfing, etc.
Seller further warrants all repair or service work performed by a factory trained representative orHamilton Manufacturing Corp. for a period of ninety (90) days from the date the repair or service work wasperformed. Purchaser’s remedies and the liabilities and obligations of Seller herein shall be limited to repair orreplacement of equipment as Seller may choose, and Seller’s obligation to remedy such defects shall notexceed the Purchaser’s depreciated value of the equipment. Purchaser EXPRESSLY AGREES this is anEXCLUSIVE REMEDY under this warranty. There are no other express or implied warranties on repair orservice work performed by a factory trained representative or Hamilton Manufacturing Corp. which extendbeyond the face hereof.
Document #101-0150 54 7/18/08
The limited warranty for repair and service work is conditioned upon the following:
1. The subject equipment has not, in the Seller’s sole opinion, been subjectedto: accident, abuse, misuse, vandalism, civil disobedience, riots, acts ofGod, natural disaster, acts of war or terrorism.
2. The Seller shall not be liable for any expense incurred by Purchaser inciden-tal to the repair or replacement of equipment and Purchaser shall assume fullresponsibility for any freight or shipping charges.
3. The coverage of this warranty shall not extend to expendable parts.4. Purchaser shall have a warranty registration card on file with Seller prior to
any claim in order for warranty protection to apply.5. No warranty coverage is applicable to any equipment used for currency
other than that specified at the time of the purchase.6. Seller expressly disclaims any warranty that counterfeit currency will not
activate said equipment.7. Seller expressly disclaims any warranty for any losses due to bill manipula-
tion or theft or loss of cash under any circumstances.8. No person or entity other than a factory trained representative or Hamilton
Manufacturing Corp. has performed or attempted to perform the subjectrepair or service.
9. Using equipment which has been serviced or repaired for anything otherthan its intended or designed use such as downloading software applicationsnot certified by Seller will void the Limited Warranty Agreement. Thisincludes software/applications such as e-mail, spyware, screen savers,viruses, worms, third party software, web search engines, cookies, spam,desktop applications, games, web surfing, etc.
THIS AGREEMENT IS MADE WITH THE EXPRESS UNDERSTANDING THAT THERE ARENO IMPLIED WARRANTIES THAT THE EQUIPMENT SHALL BE MERCHANTABLE, OR THATTHE GOODS SHALL BE FIT FOR ANY PARTICULAR PURPOSE. PURCHASER HEREBY AC-KNOWLEDGES THAT IT IS NOT RELYING ON THE SELLER’S SKILL OR JUDGMENT TO SE-LECT OR FURNISH EQUIPMENT SUITABLE FOR ANY PARTICULAR PURPOSE AND THATTHERE ARE NO WARRANTIES WHICH EXTEND BEYOND THAT WHICH IS DESCRIBED HEREIN.
The Purchaser agrees that in no event will the Seller be liable for direct, indirect, or consequentialdamages or for injury resulting from any defective or non-conforming new, repaired or serviced equipment, orfor any loss, damage or expense of any kind, including loss of profits, business interruption, loss of businessinformation or other pecuniary loss arising in connection with this Limited Warranty Agreement, or with the useof, or inability to use the subject equipment regardless of Sellers knowledge of the possibility of the same.
Document #101-0150 55 7/18/08
1026 Hamilton DriveHolland, OH 43528
Sales Phone: (888) 723-4858 Sales Fax: (419) 867-4850Customer Service Phone: (800) 837-5561 Customer Service Fax: (419) 867-4857
Parts Phone: (866) 835-1721 Parts Fax: (419) 867-4867Website: http:\\www.hamiltonmfg.com
Email Addresses:[email protected]@[email protected]
Hamilton Manufacturing Corp.