TIA_EIA-606-A Labeling Compliance Brochure

7/30/2019 TIA_EIA-606-A Labeling Compliance Brochure

1/19

TIA/EIA-606-ALABELING COMPLIANCE

BROCHURE

TIA/EIA-606-ALABELING COMPLIANCE

BROCHURE

(Featuring the PANDUIT ULTIMATE ID Network Labeling Syste

NETWORK CONNECTIVITY GROUP


2/19

For compliance with the TIA/EIA-606-A standard, PANDUIT has the solution. This brochure

will walk you through the labeling requirements of the standard and introduce you to

identification solutions specifically designed to comply with TIA/EIA-606-A. The

standard establishes guidelines for owners, end users, manufacturers, consultants,

contractors, designers, installers, and facility administrators involved in the

administration of the telecommunications infrastructure. Proper identification of your

network allows moves, adds, changes, trouble shooting, and repairs to be accomplished

faster and more efficiently. PANDUIToffers a full line of network connectivity products,

labeling products, software, and printers to assist you with TIA/EIA-606-A compliance.

The ULTIMATE ID Network Labeling System featured in this brochure was designed

specifically with the TIA/EIA-606-A standard in mind. It includes faceplates, surface mount

boxes, patch panels, marker ties, labels for desktop printers, and the PANACEA LS7

hand-held thermal transfer printer. All ULTIMATE ID hardware uses labels with a

common compact height; this not only enhances the appearance of the installation, but

also saves time and money by providing a clear and efficient way to label according to the

TIA/EIA-606-A standard. All labels are positioned adjacent to, centered and parallel to the

module they are identifying. The appearance of the installation can be further enhanced

by using a consistent font size throughout the installation. The PANACEA LS7 printer and

PANDUITdesktop labeling software can both be used to mechanically print labels with the

same font.

For detailed information on related PANDUIT identification products, request any of

the following:

ULTIMATEIDNetwork Labeling System Catalog: SA-IDCB01

PAN-CODE Identification and Labeling Solution Products: SA101N315C

PANACEA LS7 Hand-Held Thermal Transfer Printer: SA-IDCB1000A

VIPER LS6 Portable Thermal Transfer Printer: SA-ID07BR01A

ULTIMATEID

Labeling Software for WINDOWS^: SA-IDCB11 PAN-MARK 2.5 Labeling Software for WINDOWS: SA-IDCB1043A

Detailed printing instructions for ULTIMATEIDlabels with the

PANACEA LS7 Hand-Held Thermal Transfer Printer: SA-IDSP01

TIA/EIA-606-A

Labeling Compliance

Brochure

^WINDOWS is a registered trademark of Microsoft Corp.


3/19

For Technical Assistance, Call: 866-405-6654 (Outside the U.S., see back cover for Regional Directory).

Table of Contents

Roadmaps 2-3

Horizontal Link Identification - Patch Panel 4

Horizontal Link Identification - Outlet 5

Telecommunications Space Identification 8

Telecommunications Main Grounding Busbar andGrounding Busbar Identification 9

Cable Identification 6-7

Portable Printers 13

Overview of TIA/EIA-606-A 15

Computer Printable Software 14

Horizontal Link Identifier Labeling Format 16

Horizontal Link Identification - Connector 12

Horizontal Link Identification - IDC Punch Down Block 10

Firestopping Location Identification 11


4/19

TIA/EIA-606-A Labeling Compliance in the Telecommunications Space Roadmap

1 Telecommunications SpaceIdentification (see page 8)

2 Cable Identification Backbone

(see pages 6-7)

3 Telecommunications (Main) Grounding

Busbar Identification (see page 9)

5 Horizontal Link Identification IDC Punch Down Block (see page 10)

6 Cable Identification

Horizontal Link (see pages 6-7)

7 Firestopping Location Identification

(see page 11)

4 Horizontal Link Identification Patch Panel (see page 4)

2

4

3

5

6

6

1

7

2


5/19

TIA/EIA-606-A Labeling Compliance in the Work Area Roadmap

8 Horizontal Link Identification Outlet(see page 5)

9 Horizontal Link Identification Connector(see page 12)

6 Cable Identification Horizontal Link

(see pages 6-7)

6

8

9


6/19

4

Horizontal Link Identification - Patch Panel

All ULTIMATE ID Patch Panels can be identified with the following labels:

ULTIMATE IDNetwork Label ing System for Patch PanelsULTIMATE IDNetwork Label ing System for Patch Panels

Section 5.1.2 States

A horizontal link identifier, unique within the building, shall be assigned to each horizontal link and to its elements.

In the Telecommunications Space (TS), each patch panel por t shall be labeled with the an portion of theidentifier. This requirement may be met by labeling a patch panel with the a portion of the identifier, and each

port with the n portion where:

a = one to two alpha characters uniquely identifying a single patch panel, or a group of patch panels with

sequentially numbered ports

n = two to four numeric characters designating the port on a patch panel in the TS

For example:

A07 = patch panel A, position 07

The ULTIMATE ID patch panel and labeling system allows you to center the an

identifier over each port.

Desktop Laser / Ink Jet Printing Solution

*Order number of sheets required in multiples of Std. Pkg. Qty.

For detailed information on ULTIMATEIDpatch panels and labeling solutions, request the ULTIMATEIDcatalog, SA-IDCB01.

PANACEA LS7 Hand-Held Thermal Transfer Printing Solution

*Order number of cassettes required.For non-adhesive labeling solutions, do not remove liner from the label.

Patch panels which are not part of the ULTIMATEIDNetwork Labeling System can be identified by utilizing the LS7-25-1 label cassette as

an adhesive label. For a PANACEA LS7 full line product bulletin, request SA-IDCB1000A.

UILJ4

Part Number Part Description

Width

in mm

Height

in mm

Std.Pkg.

Qty.*

Std.Ctn.

Qty.

UILS7BW Black/white non-laminated polyester label cassette 0.236 5.99 26.200 8.00 1 20


Height

in mm

Length

ft m

Std.

Pkg.

Qty.*

Std.

Ctn.

Qty.

2.585 65.65 0.236 5.99 5 50Four port, white non-adhesive polyester labels, 66 labelsper sheet


7/19


Horizontal Link Identification - Outlet

*Order number of cassettes required.

For non-adhesive labeling solutions, do not remove liner from the label.

Faceplates which are not part of the ULTIMATEIDNetwork Labeling System can be identified by utilizing the LS7-25-1 label cassette as an adhesive

label. Non-ULTIMATEIDfaceplates which accept 0.4 inch high labels can be identified by utilizing the LS7-38-1 label cassette as a non-adhesive

label. For a PANACEA LS7 full line product bulletin, request SA-IDCB1000A.

ULTIMATE ID Network Label ing System for Outlets(Faceplates /Surface Mount Boxes) ULTIMATE ID Network Label ing System for Outlets(Faceplates /Surface Mount Boxes) Section 5.1.2 States

A horizontal link identifier, unique within the building, shall be assigned to each horizontal link and to its elements.

In the work area, each individual telecommunications outlet/connector shall be labeled with the horizontal link

identifier. The labeling shall appear on the connector, faceplate, or MUTOA, in a way that clearly identifies the

individual connector associated with the particular identifier. A horizontal link identifier shall have a format of

fs-an where:

f = numeric character(s) identifying the floor of the building occupied by the TS (telecommunications space)

s = alpha character(s) uniquely identifying the TS on floor f, or the building area in which the space is located

a = one to two alpha characters uniquely identifying a single patch panel or a group of

patch panels with sequentially numbered ports, an IDC connector, or a group of IDC

connectors, serving as part of the horizontal cross-connect

n = two to four numeric characters designating the port on a patch panel in the TS or the

section of an IDC connector on which, a four-pair horizontal cable is terminated in the TS

For example:

1A-B02 = origination point first floor, TS A, patch panel B, position 02

Each ULTIMATE ID faceplate/surface mount box is designed in a way that allows you tocenter the an identifier clearly over each connector, while the fs identifier canbe placed in the station space.


*Order number of sheets required in multiples of Std. Pkg. Qty.**For Electrical Ivory labels, add EI at end of part number.

For detailed information on ULTIMATEIDfaceplates and labeling solutions, request the ULTIMATEIDcatalog, SA-IDCB01.

All ULTIMATE ID Faceplates/Surface Mount Boxes can be identified with thefollowing labels:

One port label, white non-adhesive polyester labels, 264 labels per sheet

Two port labels, white non-adhesive polyester labels, 132 labels per sheet

0.680 17.27 0.236 5.99 5 50

UILJ2 1.315 33.40 0.236 5.99 5 50

Three port labels, white non-adhesive polyester labels, 99 labels per sheetUILJ3 1.950 49.53 0.236 5.99 5 50

Four port labels, white non-adhesive polyester labels, 66 labels per sheetUILJ4 2.585 65.66 0.236 5.99 5 50

Six port labels, white non-adhesive polyester labels, 66 labels per sheetUILJ6 3.855 97.92 0.236 5.99 5 50

Label sheets with 40-one port, 60-two port, 3-three port and 24-four port labels

per sheet, white non-adhesive polyesterUILJCOMBO 0.236 5.99 5 50

Part Description

Width

in mm

Height

in mm

Std.

Pkg.

Qty.*

Std.

Ctn.

Qty.




Height

in mm

Length

ft m

Std.

Pkg.

Qty.*

Std.

Ctn.

Qty.

UILJ1

Part Number**


8/19

6

Cable Identification

PANDUIT Cable Identif icat ion ProductsPANDUIT Cable Identif icat ion Products

Section 5.1.2 StatesA horizontal link identifier, unique within the building, shall be assigned to each horizontal link and to its elements.

Each end of a horizontal cable shall be labeled within 300 mm (12 in) of the end of the cable jacket with the

horizontal link identifier, which shall be visible on the exposed part of the cable jacket. This shall include each

cable in the Telecommunications Space (TS), at the work area, and at a Consolidation Point (CP), if present.

A horizontal link identifier shall have a format of fs-an where:

f = numeric character(s) identifying the floor of the building occupied by the TS

s = alpha character(s) uniquely identifying the TS on floor f, or the building area in which the space

is located

a= one to two alpha characters uniquely identifying a single patch panel or a group of patch panels with

sequentially numbered ports, an IDC connector, or a group of IDC connectors serving as part of the

horizontal cross-connect

n = two to four numeric characters designating the port on a patch panel in the TS or the section of an

IDC Connector on which a four pair horizontal cable is terminated in the TS

For example: ULTIMATE ID Solution Non-ULTIMATE IDSolutions

1A-B01 = cable origination point first

floor, TS A, patch panel B,

position 01


A unique building backbone cable identifier shall be assigned to each backbone cable between two TSs in one

building and it shall have a format of fs

1

/fs

2

-n where:

fs1 = TS identifier for the space containing the termination of one end of the backbone cable

fs2 = TS identifier for the space containing the termination of the other end of the backbone cable

n = one to two alphanumeric characters identifying a single cable with one end terminated in the TS

designated fs1 and the other end terminated in the TS designated fs2

In this format, the TS with the lesser alphanumeric identifier shall be listed first. If the entire cable is within one

TS, the format may be fs1/fs1-n. All building backbone cable identifiers in a single infrastructure should have the

same format where possible. The backbone cable identifier shall be marked on each end of the backbone cable

within 300 mm (12 in) of the end of the cable jacket.

Ultimate ID Solution Non-ULTIMATE IDSolution

For example:

1A/2A-1 = TS A on first floor to

TS A on second floor, cable 1

PANDUIT labels for laser/ink jet printers and hand-held thermal transfer printers can

be generated by a mechanical device and are made of durable polymer construction

that will withstand the effects of moisture, heat and time.

UILJ2 Label and LS7-75NL-1UIHL12-X0 or Label Cassette

UIHL22X0 Marker Tie

UILJ2 Label S100X150FAJ S100X160FAJand UICBM1M Self-Laminating Self-Laminating

Marker Tie Label Label andNWSLC-3 Sleeve


9/19

*Order number of labels required in multiples of Std. Pkg. Qty.Ûse this label with NWSLC-2 LABELCOREto identify 2 mm fiber, and with NWSLC-3 LABELCOREto identify 3 mm fiber.Use this label with NWSLC-7 LABELCOREto identify 3 mm duplex fiber.

For Technical Assistance, Call:866-405-6654 (Outside the U.S., see back cover for Regional Directory).

LABELCORE Fiber Optic Cable Identification System


*Order number of sheets required in multiples of Std. Pkg. Qty.**For Electrical Ivory labels, add EI at end of part number.For use with UICM1M-C, UIHL12-XO and UIJL22-XO ULTIMATEIDMarker Ties to mark cables and bundles up to 1 inch in diameter.For detailed information on ULTIMATEIDpatch panels and labeling solutions, request the ULTIMATEIDcatalog, SA-IDCB01.


*Order number of cassettes required.For non-adhesive labeling solutions, do not remove liner from the label.

VIPER LS6 Portable Thermal Transfer Printing Solution

*Order number of rolls required.Ûse this label with NWSLC-2 LABELCOREto identify 2mm fiber, and with NWSLC-3 LABELCOREto identify 3mm fiber.Use this label with NWSLC-7 LABELCOREto identify 3mm duplex fiber.


*Order number of cassettes required.Ûse these labels with NWSLC LABELCOREsleeves to identify fiber.

Apply LABELCORE

Sleeve to cable

Wrap label around

LABELCORE Sleeve

*Order number of sleeves required in multiples of Std. Pkg. Qty.Locate on straight section of cable at least 2" from fiber boot.

NON-ULTIMATE IDNetwork Labeling System Solutions

Part Number Part DescriptionStd. Pkg.

Qty*

Std. Ctn.

Qty

NWSLC-2

NWSLC-3

NWSLC-7

100

100

100

1000

1000

1000

Cable identification sleeve, 2mm fiber cable, yellow

Cable identification sleeve, 3mm fiber cable, orange

Cable identification sleeve, 3mm duplex fiber cable, white

UILJ2**Two port labels, non-adhesive white polyester labels, 132 labelsper sheet

1.315 33.40 0.236 5.99 5 50


Width

in mm

Height

in mm

Std.

Pkg.

Qty.*

Std.

Ctn.

Qty.



Height

in mm

Length

ft m

Std.

Pkg.

Qty.*

Std.

Ctn.

Qty.

LS7-75NL-1^ Black/white non-laminated polyester label cassette 0.708 17.98 26.200 8.00 1 20

LS7-75NL-2^ Black/clear non-laminated polyester label cassette 0.708 17.98 26.200 8.00 1 20


Width

in mm

Length

ft m

Std.

Pkg.

Qty.*

Std.

Ctn.

Qty.

S100X150FA6 White self-laminating polyolefin labels, 250/roll 1.000 25.40 1.500 38.10 0.50 12.70 0.16 4.04 0.32 8.09 1 10


Width

in mm

Length

in mm

Print-OnHeight

in mm

Min. CableDiameter

in mm

Max. CableDiameter

in mm

Std.

Pkg.

Qty.*

Std.

Ctn.

Qty.

S100X160FA6^ White self-laminating polyolefin labels, 250/roll 1.000 25.40 1.600 40.64 0.80 20.32 0.25 6.47 0.25 6.47 1 10

S100X225FA6 White self-laminating polyolefin labels, 150/roll 1.000 25.40 2.250 57.15 0.75 19.05 0.24 6.07 0.48 12.13 1 10


S100X150FAJ White self-laminating polyolefin labels 1.000 25.40 1.500 38.10 0.50 12.70 0.16 4.04 0.32 8.09 2500 12500


Width

in mm

Length

in mm

Print-OnHeight

in mm

Min. CableDiameter

in mm

Max. CableDiameter

in mm

Std.Pkg.

Qty.*

Std.Ctn.

Qty.

S100X160FAJ^ White self-laminating polyolefin labels 1.000 25.40 1.600 40.64 0.80 20.32 0.25 6.47 0.25 6.47 2500 12500

S100X225FAJ White self-laminating polyolefin labels 1.000 25.40 2.250 57.15 0.75 19.05 0.24 6.07 0.48 12.13 1000 5000

Cables and Cable Bundles can be identified with the following labels:

ULTIMATE ID Network Labeling System Solutions


10/19

8

PANDUIT Network Label ing Products for Telecommunications Space Identif icat ionPANDUIT Network Label ing Products for Telecommunications Space Identif icat ion


A Telecommunications Space (TS) identifier, unique within the building, shall be assigned to the TS, and it shall

have the format fs, where:

f = numeric character(s) identifying the floor of the building occupied by the TS


For buildings with non-numeric floors, alpha-numeric characters may be used in the f format and shall be

consistent with the floor naming convention used within the building.The TS shall be labeled with the TS identifier

inside the room so as to be visible to someone working in that room.

For example:

1A = first floor, TS A

PANDUIT labels for laser/ink jet printers and hand-held thermal transfer printers canbe generated by a mechanical device and are made of durable polymer construction

that will withstand the effects of moisture, heat and time.

Telecommunications Space Identification

Telecommunications Spaces can be identified with the following labels:


*Order number of labels required in multiples of Std. Pkg. Qty.




*Order number of rolls required.

C200X100FJJ White adhesive polyolefin labels 2.000 50.80 1.000 25.40 1000 5000


Width

in mm

Height

in mm

Std.

Pkg.

Qty.*

Std.

Ctn.

Qty.

C200X100FJ6 White adhesive polyolefin labels, 500/roll 2.000 50.80 1.000 25.40 1 10


Width

in mm

Height

in mm

Std.

Pkg.

Qty.*

Std.

Ctn.

Qty.

LS7-75NL-1 Black/white non-laminated polyester label cassette 0.708 17.98 26.200 8.00 1 20


Height

in mm

Length

ft m

Std.

Pkg.

Qty.*

Std.

Ctn.

Qty.


11/19


PANDUIT Network Labeling Products for Telecommunications

Main Grounding Busbar and Grounding Busbar

PANDUIT Network Labeling Products for Telecommunications

Main Grounding Busbar and Grounding BusbarSection 5.1.3 States

The Telecommunications Main Grounding Busbar (TMGB) identifier is used to identify the single TMGB present

in a building. The TMGB shall be labeled with the TMGB identifier. The format for the TMGB identifier shall be

fs-TMGB, where:

fs = TS (telecommunications space) identifier for the space containing the TMGBTMGB = portion of an identifier designating a telecommunications main grounding busbar

For example:1A-TMGB = first floor, TS A,telecommunications main grounding busbar


A Telecommunications Grounding Busbar (TGB) identifier is used to identify TGBs in the grounding and

bonding system. Each TGB shall be labeled with the TGB identifier. A unique TGB identifier shall be assigned

to each TGB and the format for the TGB identifier shall be fs-TGB, where

fs = TS identifier for the space containing the TGBTGB = portion of an identifier designating a telecommunications grounding busbar

All of the TGB identifiers in a single infrastructure should have the same format where possible.

For example:1A-TGB = first floor, TS A,telecommunications grounding busbar

PANDUIT labels for laser/ink jet printers and hand-held thermal transfer printerscan be generated by a mechanical device and are made of durable polymerconstruction that will withstand the effects of moisture, heat and time.

Telecommunications Main Grounding Busbar and

Grounding Busbar Identification

Telecommunications (Main) Grounding Busbars can be identified withthe following labels:








Part Number Part DescriptionWidth

in mm

Height

in mm

Std.

Pkg.

Qty.*

Std.

Ctn.

Qty.



in mm

Height

in mm

Std.

Pkg.

Qty.*

Std.

Ctn.

Qty.


Part Number Part Description Heightin mmLength

ft m

Std.

Pkg.Qty.*

Std.

Ctn.Qty.


12/19

10

Horizontal Link Identification - IDC Punch Down Block

PANDUIT Network Label ing Products for IDC Punch Down BlocksPANDUIT Network Label ing Products for IDC Punch Down BlocksSection 5.1.2 States

A horizontal link identifier, unique within the building, shall be assigned to each horizontal link and to its

elements. In the TS (telecommunications space), each section of an IDC connector (punch-down block)

terminating a four-pair cable shall be labeled with the an portion of the identifier. This requirement may be met

by labeling an IDC connector or group of IDC connectors with the a portion of the identifier, and the section of

an IDC connector terminating a four-pair cable labeled with the n portion where:

a = one to two alpha characters uniquely identifying an IDC connector, or a group of IDC connectors,

serving as part of the horizontal cross-connect

n = two to four numeric characters designating the section of an IDC connector on which a four-pair

horizontal cable is terminated

For example:

B04 = IDC block B, position 04

PANDUIT labels for laser/ink jet printers and hand-held thermal transfer printerscan be generated by a mechanical device and are made of durable polymer

construction that will withstand the effects of moisture, heat and time.

IDC Punch Down Blocks can be identified with the following labels:




*Order number of cassettes required.For non-adhesive labeling solutions, do not remove liner from label.



For non-adhesive labeling solutions, do not remove liner from label.

C750X050Y1J Punchdown block, white non-adhesive polyester labels 7.50 190.50 0.500 12.70 500 2500


Width

in mm

Height

in mm

Std.

Pkg.

Qty.*

Std.

Ctn.

Qty.

C750X050Y16 Punchdown block, white non-adhesive polyester labels, 50/roll 7.50 190.50 0.500 12.70 1 10


Width

in mm

Height

in mm

Std.

Pkg.

Qty.*

Std.

Ctn.

Qty.

LS7-50-1 Black/white laminated polyester label cassette 0.472 17.98 26.200 8.00 1 20


Height

in mm

Length

ft m

Std.

Pkg.

Qty.*

Std.

Ctn.

Qty.


13/19


PANDUIT Network Label ing Products for F irestopping

Locations

PANDUIT Network Label ing Products for F irestopping

LocationsSection 6.1.3 States

A Firestopping Location (FSL) identifier shall identify each installation of firestopping material.

The format for the firestopping location identifier shall be f-FSLn(h), where:


FSL = an identifier referring to a firestopping location

n = two to four numeric characters identifying one firestopping location

h = one numeric character specifying the hour rating of the firestopping system

All firestopping location identifiers in a single infrastructure should have the same format where possible.

Each firestopping location shall be labeled at each location where firestopping is installed, on each side of thepenetrated fire barrier, within 300 mm (12 in) of the firestopping material.

For example:

1-FSL01(2) = first floor, firestopping location

number 01, two hour rating

PANDUIT labels for laser/ink jet printers and hand-held thermal transfer printers

can be generated by a mechanical device and are made of durable polymer


Firestopping Location Identification

Firestopping Locations can be identified with the following labels:









Width

in mm

Height

in mm

Std.

Pkg.

Qty.*

Std.

Ctn.

Qty.



Width

in mm

Height

in mm

Std.

Pkg.

Qty.*

Std.

Ctn.

Qty.



Height

in mm

Length

ft m

Std.

Pkg.

Qty.*

Std.

Ctn.

Qty.


14/19

12

Horizontal Link Identification - Connector

Section 5.1.2 StatesA horizontal link identifier, unique within the building, shall be assigned to each horizontal link and to its elements.In the work area, each individual telecommunications outlet/connector shall be labeled with the horizontal linkidentifier. The labeling shall appear on the connector, faceplate, or MUTOA, in a way that clearly identifies theindividual connector associated with the particular identifier. A horizontal link identifier shall have a format offs-an where:



a = one to two alpha characters uniquely identifying a single patch panel or a group of patch panels with

sequentially numbered ports, an IDC connector, or a group of IDC connectors, serving as part of the

horizontal cross-connect

n = two to four numeric characters designating the port on a patch panel in the TS or the section of an IDC

connector on which a four-pair horizontal cable is terminated in the TS.

For example:

1A-B01 = origination point first floor,TS A, patch panel B, position 01

PANDUIT labels for laser/ink jet printers and hand-held thermal transfer printers canbe generated by a mechanical device and are made of durable polymer constructionthat will withstand the effects of moisture, heat and time.

PANDUIT Network Label ing Products for ConnectorsPANDUIT Network Label ing Products for Connectors

Horizontal Link Connectors can be identified with the following labels:







in mmHeight

in mm

Std.

Pkg.Qty.*

Std.

Ctn.Qty.



Width

in mm

Height

in mm

Std.

Pkg.

Qty.*

Std.

Ctn.

Qty.


15/19


Portable Printers

PANDUIT Network Label ing Systems Portable Pr intersPANDUIT Network Label ing Systems Portable Pr inters

Section 10.1 States

The size, color, and contrast of all labels should be selected to ensure that the identifiers are easily read.

Labels should be visible during the installation of and normal maintenance of the infrastructure. Labels should

be resistant to the environmental conditions at the point of installation (such as moisture, heat or ultraviolet

light), and should have a design life equal to or greater than that of the labeled component.

Section 10.2 States

To maximize legibility, all labels shall be printed or generated by a mechanical device.

The PANACEA LS7 Hand-Held Thermal Transfer Printer and the VIPER LS6 Portable

Thermal Transfer Printer mechanically generate labels that are made of durable

polymer construction and will withstand the effects of moisture, heat and time.

128 K file memory reduces setup time by recalling

frequently used labels

Nickel Metal Hydride battery provides longer battery life

Advanced functions including serialization, bar code

printing, vertical and horizontal lines, date and time stamp,

variety of font sizes and a symbol library containing over

40 electrical, safety and network symbols

For a VIPERLS6 full product line brochure, request

SA-ID07BR01A

Create wiremarkers, heat shrink labels, continuous tape,

component labels, bin markers, pipe markers, safety/facility

identification and network connectivity labels

High quality thermal transfer print for professional looking

labels that will not smear

AC Adapter included so you can start printing right out of

the box

Serial port/PC interfacing

Fast loading ribbon cartridge lets you slide, lock and go!

No more spacing and guess work length function alignslegends with ports

Advanced functions including serialization, vertical and

horizontal lines, symbol library and memory

Six AA alkaline batteries and hardside case included

For a PANACEA LS7 full product line brochure, request

SA-IDCB1000A

Multi-purpose printer supports ULTIMATE ID and additionalnetwork labeling requirements. For detailed printing

instructions, request SA-IDSP01

High quality thermal transfer print for professional looking

labels that will not smear

Fast loading label cassettes include both label material and

ribbon to make changing labels easy

VIPERLS6 Portable Thermal Transfer Printer

PANACEA LS7Hand-Held Thermal Transfer Printer

*Order number required in multiples of Std. Pkg. Qty.

^Cannot be used to recharge batteries.


Std. Pkg.

Qty*

Std. Ctn.

Qty

LS7

LS7-ACS^

1

1

4

6

LS7 Hand-Held Thermal Transfer Printer Kit: Includes printer, 3/4" (18mm) non-laminated black/whitecassette, hardside carrying case, wrist strap, batteries, label separator tool and operator's manual

120 VAC Adapter

LS7-CLN 1 20Cleaning Cassette

Part Number Part Description Std. Pkg.Qty* Std. Ctn.Qty

LS6-KIT

LS6-RWBLK

1

1

6

Includes printer, LS6-RWBLK ribbon, battery pack, 120 VAC adapter/charger, hardside carrying caseand operator's manual

Wax Ribbon, Black, 2" x 100'. For use with self-laminating vinyl, heat shrink and vinyl cloth materials

LS6-RRBLK 1 6Resin Ribbon, Black, 2" x 100'. For use with polyester, polyolefin and vinyl materials

LS6-RRWHT 1 6Resin Ribbon, White, 2" x 75'. For use with clear and colored polyester and vinyl tape

LS6-BP 1 Replacement Battery Pack

LS6-ACS 1 Replacement 120 VAC Adapter/Charger

LS6-PCKIT 1 PC Interface Kit. Serial Cable and VIPERLINK Software

LS6-CLN 1 5Package of 5 Printer Cleaning Cards

*Order number required in multiples of Std. Pkg. Qty.


16/19

14

Computer Printable Software

PANDUIT Network Label ing Systems ComputerPr intable SoftwarePANDUIT Network Label ing Systems ComputerPr intable Software

Section 10.1 StatesThe size, color, and contrast of all labels should be selected to ensure that the identifiers are easily read.Labels should be visible during the installation of and normal maintenance of the infrastructure. Labelsshould be resistant to the environmental conditions at the point of installation (such as moisture, heat orultraviolet light), and should have a design life equal to or greater than that of the labeled component.

Section 10.2 States

To maximize legibility, all labels shall be printed or generated by a mechanical device.

Laser/Ink Jet printers mechanically generate labels made of durable polymer


Fast and easy creation of labels for ULTIMATE IDNetwork Labeling

System patch panels, faceplates, surface mount boxes and

marker ties

Automatically aligns legends with ports on patch panels

and faceplates

Create alpha and numeric serializations

Import information from EXCEL^ and text files directly onto

the ULTIMATE ID label formats

Image library includes commonly used symbols for fax,

data and voice

Vertical line function enables users to separate legends

Automatic font sizing

On-line help function assists in understanding the TIA/EIA-606-A

standard to insure network labeling compliance

Easy to install and supplied on CD-ROM

Supports most WINDOWS printer drivers and is compatible with

standard desktop laser and ink jet printers

For ULTIMATE IDLabeling Software full product line brochure,

request SA-IDCB11

System Requirements: WINDOWS 95, 98, Me, 2000, NT 4.x, and XP; minimum 486

processor; minimum 10MB of RAM; 30 MB hard drive space

* Order number of software packages required.

ULTIMATE ID Labeling Software For WINDOWS^

PAN-MARK 2.5 for WINDOWS Labeling Software


Std.

Pkg.

Qty*

Std.

Ctn.

Qty

UISW 1 10Windows labeling software, CD-ROM

* Order number of software packages required.


Std.

Pkg.

Qty*

Std.

Ctn.

Qty

PROG-WIN2CD 1 10Windows labeling software, CD-ROM

^ WINDOWS, EXCEL and ACCESS are registered trademarks of Microsoft Corp.TrueType is a registered trademark of Apple Computing, Inc.

PAN-MARKfor Windows Labeling Software has preloaded and

ready to use, thermal transfer, dot-matrix, laser and ink jet label

formats. For use with non-ULTIMATE IDlabeling solutions

ODBC (Open Data-Base Connectivity) allows importing of

information from electronic databases such as EXCEL and

ACCESS^ directly onto the label formats Easy to install and supplied on CD-ROM

Uses a full range of WINDOWS fonts including TrueType fonts

Use image library to add commonly used symbols to your labels

(Fax, Data, Voice, etc.)

Import Bitmap (.bmp) graphic images on to a label

Create Alpha and numeric serializations

For PAN-MARKfor Windows full product line brochure,

request SA-IDCB1043A

System Requirements: WINDOWS 95, 98, Me, 2000, NT 4.x, and XP; minimum 486

processor; minimum 8MB of RAM; 30 MB hard drive space


17/19

Labeling Solutions for TIA/EIA-606-A

The TIA/EIA-606-A standard establishes guidelines for owners, end users, manufacturers, consultants,

contractors, designers, installers, and facilities administrators involved in the administration of the

telecommunications infrastructure.

Four classes of administration are specified in the standard, to accommodate diverse degrees of

complexity present in the telecommunications infrastructure. The specifications for each class includerequirements for identifiers, records, and labeling.

Class 1addresses the administration needs of a premises that is served by a single

telecommunications space (TS) containing its telecommunications equipment.Required in class 1 administration are identifiers for the TS, any Telecommunications Main Grounding

Busbar, and all elements of the horizontal links.

For a copper horizontal link, the elements include:

the connecting hardware (e.g., patch panel port or the section of a punchdown blockterminating a four-pair horizontal cable)

a four-pair horizontal cable

a telecommunications outlet/connector terminating a four-pair horizontal cable in the work areaIf a consolidation point (CP) is present: the segment of four-pair horizontal cable extending from the TS to the CP connecting hardware

the CP connecting hardware or section of a punchdown block terminating a four-pair horizontal cable the segment of four-pair horizontal cable extending from the CP connecting hardware to the outlet/

connector of a multi-user telecommunications outlet assembly (MUTOA) or to the work area outlet

If a MUTOA is present: a telecommunications outlet/connector in the MUTOA

For an optical fiber horizontal link, the elements include: a pair of optical fiber terminations on a patch panel in the TS

a pair of optical fibers in a cable

a pair of optical fiber terminations in the work area a telecommunications outlet/connector terminating a pair of optical fibers in the work area

If a consolidation point (CP) is present: the segment of optical fiber cable extending from the TS to the CP connecting hardware. the CP connecting hardware or section terminating a pair of optical fibers

the segment of optical fiber cable extending from the CP connecting hardware to the outlet/connector of

a multi-user telecommunications outlet assembly (MUTOA) or to the work area outlet.

Class 2administration provides for telecommunications infrastructure administration

needs of a single building or tenant that is served by a single or multiple TSswithin a single building. Class 2 administration includes all elements of class 1 administration, plusidentifiers for backbone cabling, multiple-element grounding and bonding systems, and firestopping.

Class 3administration addresses the needs of a campus, including its buildings and

outside plant elements. Class 3 administration includes all elements of class 2administration, plus identifiers for buildings and interbuilding cabling. Administration of pathways andspaces, and of outside plant elements is recommended.

Class 4administration addresses the needs of a multi-site system. Class 4

administration includes all elements of class 3 administration, plus anidentifier for each site, and optional identifiers for wide area network connections.


18/19

16

PANDUIT Identification Products can assist you with all the labeling procedures required by this standard.The size, color, and contrast of all labels should be selected to ensure that the identifiers are easily read.Labels should be visible during the installation of and normal maintenance of the infrastructure. Labels should

be resistant to the environmental conditions at the point of installation (such as moisture or heat), and shouldhave a design life equal to or greater than that of the labeled component. To maximize legibility, all labels shall

be printed or generated by a mechanical device. Panduit provides everything you need to comply with the

TIA/EIA-606-A standard for all of your structured cabling labeling requirements!

Horizontal Link Identifier Labeling Format

A horizontal link identifier shall have a format of fs-anwhere:

f = numeric character(s) identifying the floor of the building occupiedby the Telecommunications Space (TS)

s = alpha character(s) uniquely identifying the TS on floor f, or thebuilding area in which the space is located

a= one to two alpha characters uniquely identifying a single patchpanel, a group of patch panels with sequentially numbered ports,

an IDC connector, or a group of IDC connectors, serving as partof the horizontal cross-connect

n= two to four numeric characters designating the port on apanel in the TS, or the section of an IDC connector on which afour pair horizontal cable is terminated in the TS

EXAMPLE- 1A-A004 = Origination Point 1st Floor, Closet A, Panel A, Position 004

Floor (1)

TelecommunicationsSpace (A)

Patch Panel ID (A)

Port ID (004)

R = required identifier for class, when corresponding element is presentO = optional identifier for class

Identifier

fs

fs-an

fs-TMGB

fs-TGB

fs1/fs2-n

fs1/fs2-n.d

f-FSLn(h)

[b1-fs1]/[b2-fs2]-n

[b1-fs1]/[b2-fs2]-n.d

b

c

fs-UUU.n.d(q)

fs1/fs2-UUU.n.d(q)

c-UUU.n.d(q)

[b1-fs1]/[b2-fs2]-UUU.n.d(q)

TextClauses

5.1.1

5.1.2

5.1.3

5.1.4

6.1.1

6.1.2

6.1.3

7.1.2

7.1.3

7.1.1

8.1.1

annex B

annex B

annex B

annex B

[c1-b1-fs1]/[c2-b2-fs2]-UUU.n.d(q) annex B

Description of Identifier

telecommunications space (TS)

horizontal link

telecommunications main grounding busbar

telecommunications grounding busbar

building backbone cable

building backbone pair of optical fiber

firestop location

campus backbone cable

campus backbone pair of optical fiber

building

campus or site

intra-space pathway

building pathway

outside plant pathway

campus pathway

inter-campus element

Class of Administration

1 2 3 4

R R R R

R R R R

R R R R

R R R R

R R R

R R R

R R R

R R

R R

R R

R

O O O

O O O

O O

O O

O


19/19

NETWORK CONNECTIVITY GROUP

All PANDUIT PAN-NET non-consumable products have a 20 year warranty. When installedper TIA/EIA or ISO/IEC standards, the PANDUIT PAN-NET System will operate theapplication(s) which the system was designed to support. Applications may include, butare not limited to: 10/100/1000 Mbps Ethernet (IEEE 802.3), 4/16 Mbps Token Ring (IEEE

802.5), 155/622/1.25 Gbps ATM, SONET, FDDI/CDDI and ISDN.In order to qualify for the warranty, the system must be installed per the following: 1. Meetall TIA/EIA commercial building wiring standards. 2. PANDUITcategorized product mustbe used in conjunction with an equivalent or higher Category UL or ETL verified cable. 3.PANDUITproducts must be installed per appropriate PANDUITinstruction sheets. Note: Allnetworks shall be installed per applicable standards and manufacturers guidelines.If any PANDUIT PAN-NET product fails to perform as stated above, PANDUITwill providenew components at no charge. THIS WARRANTY IS MADE IN LIEU OF AND EXCLUDESALL OTHER WARRANTIES, EXPRESSED OR IMPLIED. THE IMPLIED WARRANTIES OFMERCHANTABILITY AND FITNESS FOR A PARTICULAR USE ARE SPECIFICALLYEXCLUDED. Neither seller nor manufacturer shall be liable for any other injury, loss ordamage, whether direct or consequential.

All PANDUIT electrical products are warranted to be free from defects in material andworkmanship at the time of sale but our obligation under this warranty is limited to thereplacement of any product proved to be defective within 6 months (for product) or 90days (for tools) from the date of delivery. Tool warranty is void if PANDUIT tools are

modified, altered or misused in any way. Use of PANDUIT tooling with any product otherthan the specified PANDUITproducts for which the tool was designed, constitutes misuse.Before using, user shall determine the suitability of the product for his intended use anduser assumes all risk and liability whatsoever in connection therewith.This warranty is made in lieu of and excludes all other warranties, expressed or implied.THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULARUSE ARE SPECIFICALLY EXCLUDED. Neither seller nor manufacturer shall be liable for anyother injury, loss or damage, whether direct or consequential, arising out of the use of, orthe inability to use, the product. The information contained in this literature is based on ourexperience to date and is believed to be reliable. It is intended as a guide for use by personshaving technical skill at their own discretion and risk. We do not guarantee favorableresults or assume any liability in connection with its use. Dimensions contained herein arefor reference purposes only. For specific dimensional requirements consult the factory.This publication is not to be taken as a license to operate under, or a recommendation toinfringe any existing patents. This supersedes and voids all previous literature, etc.

USA: Contact PANDUIT Corporate headquarters or visit our website at www.panduit.com/ncg for a listing of localsales representatives in the USA. INTERNATIONAL: Call our regional Headquarters Offices or visit our website tolocate PANDUITsales personnel and distributors in your area:

TIA_EIA-606-A Labeling Compliance Brochure

Documents

Transcript of TIA_EIA-606-A Labeling Compliance Brochure