This Illustration Example Uses · 2020. 10. 16. · Project: X-Band Repeater with 2 BTECH Mobiles...
Transcript of This Illustration Example Uses · 2020. 10. 16. · Project: X-Band Repeater with 2 BTECH Mobiles...
![Page 1: This Illustration Example Uses · 2020. 10. 16. · Project: X-Band Repeater with 2 BTECH Mobiles BaoFengTech.com BaoFeng Tech Page 1 of 4 PROJECT: CROSS BAND REPEATER WITH 2 BTECH](https://reader036.fdocuments.net/reader036/viewer/2022081410/609e7f62da69ae351f5768f1/html5/thumbnails/1.jpg)
Project:X-BandRepeaterwith2BTECHMobiles BaoFengTech.com BaoFengTech
Page1of4
PROJECT:CROSSBANDREPEATERWITH2BTECHMOBILES
WHAT’SNEEDED:RJ-45CABLE (Diagram on Page 4)
2BTECHMOBILESThisIllustrationExampleUses:
136.025MHzto465.025MHz–PL(CTCSS)74.4Hz
SETTDR(DualWatch)‘OFF’ONBOTHRADIOS
---------------------------------
1:Firstsettheparametersonthetwomobiles.Onthefirstmobileselectthe
lowerdisplay(withtheA/BButton).Setthefrequencyto465.025MHz(oryour
ownUHFfrequency)
The frequencies used in this guide are for illustrative purposes only. It is
the responsibility of the user to program frequencies that he(she) has
been granted the authority to use.
![Page 2: This Illustration Example Uses · 2020. 10. 16. · Project: X-Band Repeater with 2 BTECH Mobiles BaoFengTech.com BaoFeng Tech Page 1 of 4 PROJECT: CROSS BAND REPEATER WITH 2 BTECH](https://reader036.fdocuments.net/reader036/viewer/2022081410/609e7f62da69ae351f5768f1/html5/thumbnails/2.jpg)
Project:X-BandRepeaterwith2BTECHMobiles BaoFengTech.com BaoFengTech
Page2of4
On the other radio select the upper display (with the A/B Button). Set the
frequencyto136.025MHz(oryourownVHFfrequency)
2:OnbothBTECHmobileradiossetthePLToneswithMENUS11and13. In
thisexamplesetR-CTCS(Menu11)to74.4HzandT-CTCS(Menu13)to74.4Hz
![Page 3: This Illustration Example Uses · 2020. 10. 16. · Project: X-Band Repeater with 2 BTECH Mobiles BaoFengTech.com BaoFeng Tech Page 1 of 4 PROJECT: CROSS BAND REPEATER WITH 2 BTECH](https://reader036.fdocuments.net/reader036/viewer/2022081410/609e7f62da69ae351f5768f1/html5/thumbnails/3.jpg)
Project:X-BandRepeaterwith2BTECHMobiles BaoFengTech.com BaoFengTech
Page3of4
3:EnterMENU43REP-MandselectCTDCSfortwomobiles–thiswillrequire
the repeater forwarding (X-Band Repeat) to activate once the confirmed PL
signal(CTCSSorDCS)isreceivedwilltransmititon.
4: Exit the Menus and connect the radios with a RJ-45 cable (diagram on
page 4). Insure your external antennas are not in close proximity to avoid
interference.
![Page 4: This Illustration Example Uses · 2020. 10. 16. · Project: X-Band Repeater with 2 BTECH Mobiles BaoFengTech.com BaoFeng Tech Page 1 of 4 PROJECT: CROSS BAND REPEATER WITH 2 BTECH](https://reader036.fdocuments.net/reader036/viewer/2022081410/609e7f62da69ae351f5768f1/html5/thumbnails/4.jpg)
Project:X-BandRepeaterwith2BTECHMobiles BaoFengTech.com BaoFengTech
Page4of4
WIRE PINS: 2 TO 5, 3 TO 8, 4 TO 4, 5 TO 2, 6 TO 6, 8 TO 3
5:IftheradioreceivesthecarrierfrequencywiththerequiredCTCSSorDCS
tone(dependingonyourconfiguration)theradioswillnowpassalongand
transmitthesignalfromVHF-UHForviceversa as a cross-band repeater
NOTES:THISISONLYRECOMMENDEDTOSUPPORTCROSS-BANDREPEATING– DO
NOTUSE2VHFOR2UHFFREQUENCIES
MAKESURETHETWOANTENNASAREFARAWAYINORDERTOPREVENT
THEINTERFERENCEBETWEENTHETWOBTECHMOBILES