Thick Cylinder Full
-
Upload
tangtszloong -
Category
Documents
-
view
83 -
download
6
description
Transcript of Thick Cylinder Full
BDA 37301 SOLID MECHANICS 2 LABORATORY 6
THICK CYLINDER
TAN KANG HUAI AD120174MUHAMMAD NURSYARAFFI BIN MOHD NAZRI AD120037TANG TSZ LOONG AD120160TEE JIANG HAO AD120154NURUL NADIRAH NASHARUDIN DD120066
UNIVERSITI TUN HUSSEIN ONN MALAYSIA Faculty of Mechanical and Manufacturing Engineering
The hoop stress is the force exerted circumferentially (perpendicular both to the axis and to the radius of the object) in both directions on every particle in the cylinder wall
The difference between a thin cylinder and a thick cylinder is that a thick cylinder has a stress in the radial direction as well as a circumferential stress and longitudinal stress.
Hoop stress, σH
Radial stress, σR
o where A and B are constants which can be determine using its boundary conditions
THEORY
OBJECTIVE
to demonstrate and analyze the stress systems in a thick cylinder.
The value in pressure gauge adjusted is not synominous with the computer pressure value
For computerized 5 MPa, the value in pressure gauge was a bit higher that value.
It took time for pressure to reach a stable value in computer as the reading always fluctuating.
All the strain value in every part of thick cylinder were stimulated in computer.
OBSERVATION
Gun barrel Piping
Pressure vessel
APPLICATION
Radius Gauge Number Nature of Strain Measured Strain(x 10^-6) Theoretical Strain(x 10^-6) Error Difference
1 Ɛh 42.2 45.3 3.12 ƐR -69.7 -39.3 -24.4
3 Ɛh 22.8 28.6 5.84 ƐR -36.4 -22.6 13.8
5 Ɛh 11.6 19.3 7.76 ƐR -29.2 -13.4 15.8
7 Ɛh 3.2 13.5 10.38 ƐR -19.16 -7.6 12
9 Ɛh 1.7 11.3 9.610 ƐR -18.1 -5.4 12.7
18.5 11 Ɛh 93.6 99.8 6.212 ƐL -4.9 -2.9 2
13 Ɛh -1.3 8.9 7.1
28
36
45
75
63
56
Table 1: Measured and calculated strain gauge values
RESULT
Formula for calculate strain gauge values
Radiusr/mm σh (N/m^2) σR (N/m^2) σh (N/m^2) σR (N/m^2)18.5 7680000 -2530000 5640000 -500000028 1740000 -4080000 2650000 -200000036 880000 -2370000 1730000 -108000045 160000 -2080000 1220000 -58000056 -270000 -1520000 910000 -26000063 -350000 -1440000 780000 -14000075 -110000 -350000 650000 0
Derived Theoretical
Table 2:Derived and theoretical stress values
Formula for calculate derived and theoretical stress
DISCUSSION
1. Radius increases, hoop stress decreases.2. Radius increases, radius stress increases.3. Both fulfilled Lame’s equation.4. Obvious deviation, errors like systematic existed5. Piping industry – maximum pressure & strain to avoid
break
We can conclude that:
Student able to know about stress and strain in cylinder.Experiment has achieved the objective. The data value obtained for experimental and theoretical are
different because of error.Parallax error while observe and taking reading.Overcome by taking reading repeatedly.Make sure the apparatus in good condition.
CONCLUSION