The Peris taltic Transport of MHD Eyring -Powell Fluid through ...walls on peristaltic flow through...
Transcript of The Peris taltic Transport of MHD Eyring -Powell Fluid through ...walls on peristaltic flow through...
The Peristaltic Transport of MHD Eyring-Powell
Fluid through Porous Medium in a Three
Dimensional Rectangular Duct 1Hayat A. Ali and
2Ahmed M. Abdulhadi
1Department of Mathematics,
Baghdad University, Baghdad, Iraq.
[email protected] 2Department of Mathematics,
Baghdad University, Baghdad, Iraq.
Abstract This paper devotedly study the peristaltic transport of MHD Eyring-
Powell fluid flow through a porous medium in a three dimensional
rectangular duct with the effect of no slip condition and complaint wall.
The relevant equations(mass, motion) are first modelled and then
simplified under the assumptions of long wavelength and low Reynolds
number approximation. Homotopy perturbation method (HPM)is applied
to obtain an approximate analytic solution for the velocity distribution.
Physical behaviors of different parameter of interest have been presented
graphically for velocity, and trapping phenomena.
International Journal of Pure and Applied MathematicsVolume 119 No. 18 2018, 273-286ISSN: 1314-3395 (on-line version)url: http://www.acadpubl.eu/hub/Special Issue http://www.acadpubl.eu/hub/
273
1. Introduction
In the history of fluid dynamics, the area of peristaltic transportation has
obtained significant attraction because of its considerable contribution in the
fields of engineering and biomechanics as this process remains vital in many
biological mechanism and biomedical industry. Peristalsis is a mechanism of
pumping fluids in ducts when a progressive wave of area contraction or
expansion propagates along the length of a distensible tube containing fluid. It
includes the transportation of urine from the kidney to the bladder, food through
the digestive tract, bile from the gall-bladder into the duodenum, movement of
ovum in the fallopian tube, the design of roller pumps, etc.[14-16].Beside that
non-Newtonian fluids get more attention because of their vigorous use in
industrial applications, particularly in chemical engineering processes and
polymer processing. Due to this importance of non-Newtonian fluids, in 1944,
Powell and Eyring proposed a new fluid model known as Eyring-Powell fluid.
Even though this model is mathematically more complex, but deserves more
consideration because of its distinct advantages over the non-Newtonian fluid
models. Recently, some effective researches have been done on peristaltic flow
of non-Newtonian fluid in three dimensional rectangular channel with
compliant walls with different flow conditions. Reddy et al.[11] have recently
disclosed the theory that the sagittal cross- section of the uterus may be better
analyzed by a channel of rectangular cross- section than a two dimensional
channel. After that Ellahi et al.[13] examined the mathematical analysis of
peristaltic transport of an Eyring-Powell fluid through a porous rectangular
duct. Also Elliahi et al. [15] investigated the peristaltic flow in non- uniform
rectangular duct under the effects of heat and mass transfer. Effect of lateral
walls on peristaltic flow through an a symmetric rectangular duct discussed by
Mekeimer et al. [12]. Akram et al.[14] studied the same effect on peristaltic
flow of a couple stress fluids in a non- uniform rectangular duct. As well as
Abbas et al.[4] examined three dimensional peristaltic flow of hyperbolic
tangent fluid in non-uniform channel having flexible walls. In the same topic
Riaz et al.[10] detected the effect of wall properties on unsteady peristaltic flow
of an Eyring- Powell fluid in three dimensional rectangular duct .
Motivated by the above studies, in this paper the peristaltic flow of MHD
Eyring-Powell fluid in a rectangular duct through a porous medium under the
effect of compliant walls was analyzed. The flow is taken to be unsteady and
then in wave frame under the assumptions of long wavelength and low Renolds
number, the reduced non- dimensional partial differential equation is solved by
employing homotopy perturbation method (HPM) for velocity field function.
Finally the physical feature of the pertinent parameters is discussed by plotting
velocity and stream function.
2. Mathematical Formulation
Consider the unsteady peristaltic transport of an incompressible conductive
Eyring-Powell fluid in a duct of rectangular cross- section through a porous
International Journal of Pure and Applied Mathematics Special Issue
274
medium having the channel width 2π and height2π. The Cartesian coordinate
system is considered in such a way that π β axis is taken along the axial
direction, π β axis along the lateral direction, and π βaxis is along the vertical
direction of rectangular channel. The flow is observed by the peristaltic
sinusoidal waves travelling with velocity π, propagating along the walls of the
channel.
The peristaltic waves through a duct of rectangular cross- section is prescribed
as
π = Β± π + π πππ 2π
π π β ππ‘ (1)
In which π and π are the amplitudes of the waves, π is the wavelength, π‘ is the
time, and π is the direction of wave propagation. The walls parallel to ππ-
plane. The lateral velocity is considered here to be zero since there is no change
in lateral direction of the duct cross- section. The velocity fieldfor unsteady
flows is π = π π, π, π, π‘ , 0, π π, π, π, π‘ where π and π are the axial and
vertical component of the velocity respectively. A uniform magnetic field
π΅ = (0,0, π½0) is applied normal to the flow, with this assumption the magnetic
Renolds number is small so that the induced magnetic field is neglected.
The governing equations for the flow problem are stated as:
The continuity equation ππ
ππ+
ππ
ππ= 0, (2)
π β component momentum equation
π ππ
ππ‘+ π
ππ
ππ+ π
ππ
ππ = β
ππ
ππ+
ππ ππ
ππ+
ππ ππ
ππ+
ππ ππ
ππβ ππ½0
2π βπ
π0π, (3)
π β component momentum equation
0 = βππ
ππ+
ππ ππ
ππ+
ππ ππ
ππ+
ππ ππ
ππ, (4)
π β component momentum equation
π ππ
ππ‘+ π
ππ
ππ+ π
ππ
ππ = β
ππ
ππ+
ππ ππ
ππ+
ππ ππ
ππ+
ππ ππ
ππ, (5)
where π ππ , π, π = π, π, π designates the extra stress tensor for Eyring- Powell
fluid on a face whose normal is the π-axis and act on the face π-axis,it is
described as[10]
π ππ = πππππππ
+1
π½sinhβ1(
1
π1
πππ
πππ ) , (6)
Where ππ = π, π, π , ππ = π, π, π .
π1 and π½ represent the material parameters of Eyring- Powell fluid, The term
sinhβ1 is approximated using the second order approximation of the hyperbolic
International Journal of Pure and Applied Mathematics Special Issue
275
sine function as bellows:
sinhβ1 1
π1
πππ
πππ β
1
π1
πππ
πππβ
1
6
1
π1
πππ
πππ
3
1
π1
πππ
πππ βͺ 1 (7)
Then Eq.(6) will be written as
π ππ = πππππππ
+1
π½π1
ππππππ
β1
6π½π13 πππ
πππ
3
(8)
The corresponding complaint boundary conditions are
No- slip condition at the walls
π = 0 , ππ‘ π = Β±π π = 0, ππ‘ π = Β±π»(π, π‘)
(9)
The governing equation for the flexible wall may be presented as [10]
πΏ(π»(π, π‘)) = π β π0, (10)
Whereπ0is pressure on outside surface of the wall due to tension in muscle,
which is assumed to be zero here.L is an operator used to represent the motion
of stretched membrane with viscosity damping forces such that
πΏ = ππ2
ππ‘2 + π·π
ππ‘+ π΅1
π4
ππ4 β ππ2
ππ2 + π1, (11)
In the above equation, π is mass per unit area, π· is coefficient of the viscosity
damping membrane, π΅1 is flexural rigidity of the plate, πis elastic tension in the
membrane, and π1 is spring stiffness.
Defining a wave frame π₯, π¦, π§ moving with the velocity π away from the fixed
frame π, π, π, π‘ and non- dimensional quantities by the following
transformations
π₯ = π β ππ‘ , π¦ = π , π’ = π β π , π£ = π, π€ = π, π π₯, π¦, π§ = π π, π, π, π‘ (12)
where π’, π£, π€ are the velocity components in the wave frame π₯, π¦, π§ .
Introducing the non- dimensional quantities that used to simplify the governing
equations as follows:
π₯ =π₯
π , π¦ =
π¦
π , π§ =
π§
π, π’ =
π’
π , π€ =
π€
ππΏ , π‘ =
ππ‘
π, β =
π» π ,π‘
π , π =
π2π π₯
πππ, πΏ =
π
π , π =
ππ π₯
ππ , π π =
πππ
π,
π΅0
=
1
ππ½ π1, π΄ =
π΅0
6
π
π1π
2, π =
π0
π2 , π2 =ππ½0
2π2
π, π =
π
π , πΌ2 =
1
π+ π2 , π½1 =
π
π, π’ =
ππ
ππ§, π€ = β
ππ
ππ₯ (13)
where π₯ , π¦ , π§ , π’ , π€ , π‘ , β, π, π , π π, πΏ, π, π½1, π΅0, π΄, π, π, describe the dimensionless
axial coordinate, lateral coordinate, transverse coordinate, axial , transverse
velocity components, time, stream function, pressure, Renolds number, wave
number, amplitude ratio, the Eyring-Powell parameters, Hartman number, the
porosity parameter.
Under the assumption of long wavelength π β β and low Reynolds
number π π β 0 , the governing Eqs. (2)β (5) for the EyringβPowell fluid in
International Journal of Pure and Applied Mathematics Special Issue
276
non-dimensional form are achieved as: ππ’
ππ₯+
ππ€
ππ§= 0, (14)
ππ
ππ₯= π½1
2 πππ₯π¦
ππ¦+
πππ₯π§
ππ§β πΌ2 π’ + 1 , (15)
ππ
ππ¦= 0 , (16)
ππ
ππ§= 0 , (17)
While the non- dimensional of extra stress components are
ππ₯π¦ = 1 + π1 ππ’
ππ¦ β π½1
2π΄ ππ’
ππ¦
3
, (18)
ππ₯π§ = 1 + π1 ππ’
ππ§ β π΄
ππ’
ππ§
3
, (19)
The corresponding compliant boundary conditions in non-dimensional form are
described as:
π’ = 0 , ππ‘ π¦ = Β±1 π’ = 0, ππ‘ π§ = Β±β(π₯, π‘)
(20)
where β π₯, π‘ = Β±1 Β± β πππ 2π(π₯ β π‘) and 0 β€ β β€ 1.
and the dimensionless of wall properties is given as
πΈ1π2
ππ‘2 + πΈ2π
ππ‘+ πΈ3
π4
ππ4 β πΈ4π2
ππ2 + πΈ5 β π₯, π‘ = π, (21)
In above relation,πΈ1 = ππ3π/π3π, πΈ2 = π·π3/π2π , πΈ3 = π΅1π3/ππ5π,πΈ4 =
ππ3/ππ3π ,and πΈ5 = π1π3/πππ ,are the non-dimensional elasticity parameters.
From Eqs.(16) and (17) one can deduce that the pressure π is not a function of
π¦ and π§.
Differentiating Eq.(15) w.r.t π₯ and making use of Eqs.(16),(17),and(21) yields 1
1+π1
π
ππ₯ πΈ1
π2
ππ‘2 + πΈ2π
ππ‘+ πΈ3
π4
ππ4 β πΈ4π2
ππ2 + πΈ5 β π₯, π‘ =
π½12 π2π’
ππ¦2 +π2π’
ππ§2 β πΌ2
1+π1 π’ + 1 β
3π΄
1+π1 π½1
4 ππ’
ππ¦
2 π2π’
ππ¦2 + ππ’
ππ§
2 π2π’
ππ§2 , (22)
It is noticed here when π½1 = 0 the problem convert to two- dimensional
channel and π½1 = 1 gives the square duct.It is also observed that π1 = π΄ = 0
reproduce the viscous fluid case in rectangular duct. However when πΌ2 β 0
the solution of Riaz et al. [10] is recovered.
3. Solution of the Problem
The solution of the previously mentioned nonlinear partial differential equation
has beencalculated by homotopy perturbation method [HPM], which is defined
as []
π» π’ π₯, π¦, π§, π‘ ;π = πΏ1 π’ π₯, π¦, π§, π‘ β πΏ1 π’ 0 π₯, π¦, π§, π‘ + ππΏ1 π’ 0 π₯, π¦, π§, π‘ + π β3π΄
1+π1 π½1
4 ππ’
ππ¦
2 π2π’
ππ¦2+
International Journal of Pure and Applied Mathematics Special Issue
277
ππ’
ππ§
2 π2π’
ππ§2 β
πΌ2
1+π1 β πΆ π₯, π‘ = 0 (23)
whereβ 0,1 , is called homotopy parameter which under the condition that
for π = 0 ,the initial guess achieved and for π = 1 we seek the final
solution.
Hereπ’ 0is an initial guess for the solution of Eq. (22), which satisfies the
boundary conditions Eq.(20). πΏ1is the linear operator which defined as
πΏ1 π’ = π½12 π2π’
ππ¦2 +π2π’
ππ§2 β πΌ2
1+π1 π’, (24)
and πΆ π₯, π‘ =1
1+π1
π
ππ₯ πΈ1
π2
ππ‘2 + πΈ2π
ππ‘+ πΈ3
π4
ππ4 β πΈ4π2
ππ2 + πΈ5 β π₯, π‘ , (25)
We choose the following initial guess
π’ 0 π₯, π¦, π§, π‘ =(1 βπ¦2)
πΌπ½ 2 + π§2ββ2
πΌ2 , (26)
Let us expand the solution of Eq. (23)as a power series in π as follows:
π’ = π’0 + ππ’1 + π2π’2 + β―, (27)
Substituting Eq.(27) into Eq.(23) and then comparing the same power of π and
choosing powers of π from zero to one, we obtain the following problems
together with the corresponding boundary conditions.
Zeroth- Order Deformation
The differential equation of the zero- order with the boundary conditions is
obtained as follows:
πΏ1 π’0 π₯, π¦, π§, π‘ β πΏ1 π’ 0 π₯, π¦, π§, π‘ = 0, (28)
π’0 = 0 , ππ‘ π¦ = Β±1 π’0 = 0, ππ‘ π§ = Β±β(π₯, π‘)
(29)
From Eq.(23), the zero- order solution is
π’0 π₯, π¦, π§, π‘ = π’ 0 π₯, π¦, π§, π‘ =(1 βπ¦2)
πΌπ½ 2 + π§2ββ2
πΌ2 , (30)
First- Order Deformation
The first order equation is constructed as
π½12 π2π’1
ππ¦2+
π2π’1
ππ§2β
πΌ2
1+π1 π’1 β
3π΄
1+π1 π½1
4 ππ’0
ππ¦
2 π2π’0
ππ¦2+
ππ’0
ππ§
2 π2π’0
ππ§2 β
πΌ2
1+π1 β πΆ π₯, π‘ = 0, (31)
Associated with the boundary conditions
π’1 = 0 , ππ‘ π¦ = Β±1 π’1 = 0, ππ‘ π§ = Β±β(π₯, π‘)
(32)
by substituting the zero- order solution π’0 π₯, π¦, π§, π‘ into Eq.(31) and with some
simplification along with boundary conditions, the resulting partial differential
equation is derived as below:
International Journal of Pure and Applied Mathematics Special Issue
278
π½12 π2π’1
ππ¦2 +π2π’1
ππ§2 β πΌ2
1+π1 π’1 =
24π΄
1+π1 π§2
πΌ6 βπ¦2
π½12πΌ6 +
πΌ2
1+π1 + πΆ π₯, π‘ = 0, (33)
π’1 = 0 , ππ‘ π¦ = Β±1 π’1 = 0, ππ‘ π§ = Β±β(π₯, π‘)
(34)
Incorporating with the method of eigen function expansion, the final closed
form of solution to Eq.(33).
π’1 π₯, π¦, β, π‘ = ππ π¦ πΆππ πππ§,βπ=1 (35)
where
ππ π¦ = π1πΆππ β πππ¦ + π2 + π3π¦2, (36)
ππ = ππ 2
π½12 +
πΌ2
π½12 1+π1
, (37)
π1 =1
πΆππ βππ
48π΄πΆππ ππ
π2π 1+π1 πππ½1
4βπΌ6 +96π΄πΆππ ππ
π4π 1+π1 πππ½1
4βπΌ6 +1
π2ππ½1
2 48π΄
1+π1 βπΌ6 2πΆππ ππ
ππ 3 β
β2πΆππ ππ
ππ β
2πΆππ ππ
ππβ
πΌ2
1+π1 + πΆ π₯, π‘ , (38)
π2 =β96π΄πΆππ ππ
π4π 1+π1 πππ½1
4βπΌ6 β1
π2ππ½1
2 48π΄
1+π1 βπΌ6 2πΆππ ππ
ππ 3 β β2πΆππ ππ
ππ β
2πΆππ ππ
ππβ
πΌ2
1+π1 +
πΆ π₯, π‘ , (39)
π3 =β48π΄πΆππ ππ
π2π 1+π1 πππ½1
4βπΌ6 , (40)
The final solution of Eq.(31) will be obtained at π β 1, which can be defined as
π’ π₯, π¦, π§, π‘ =(1 βπ¦2)
πΌπ½ 2 + π§2ββ2
πΌ2 + ππ π¦ πΆππ 2πβ1 π
2β π§,β
π=1 (41)
4. Graphical Results and discussion
In this section, we inspect physical effect of various parameters on the axial
velocity and the stream function are recorded graphically.
Velocity Profile
The velocity profile is sketched for both three and two dimensional channel
upon the variation of important parameters involved in the expression of
velocity field via Figures. (1)-(6). Figs. (1), and (2) show the variation of
velocity axial against the wall tension parameterπΈ1, and viscous dampingπΈ3
respectively. It is depicted that the velocity profile decreases for ascending
values of πΈ1but An increasing function of the velocity field is seen for
ascending values of πΈ3. Completely opposite influence for Eyring-Powell fluid
parameters π΄ and π1on the axial velocity is noticed through Figs.(3) and (4)
respectively, i.e. the velocity axial enhances for greater values of π΄and
decreasing againstπ1enhancement. One can observed from Fig. (5) a decreasing
function for velocity field with the rise of Hartman number π. Fig.(6) describes
that when the porosity parameter π increases the velocity profile increases very
International Journal of Pure and Applied Mathematics Special Issue
279
rapidly.
(a) (b)
Fig. 1: Axial velocity π’ versus π§- direction for different values of wall
tensionπΈ1 and with fixed values of parameters {πΈ2 = 0.2, πΈ3 = 0.1, πΈ4 =0.1, πΈ5 = 0.3, π = 0.9, π΄ = 2, π = 0.8, π = 1, π½1 = 0.02, π = 0.09, π₯ =0.02, π‘ = 0.01, π¦ = 0} in (a) Two dimension (b) Three dimension.
(a) (b)
Fig. 2: Axial velocity π’ versus π§- direction for different values of viscous
dampingπΈ3 and with fixed values of parameters {πΈ1 = 0.1, πΈ2 = 0.2, πΈ4 =0.1, πΈ5 = 0.3, π = 0.9, π΄ = 2, π = 0.8, π = 1, π½1 = 0.02, π = 0.09, π₯ =0.02, π‘ = 0.01, π¦ = 0} in (a) Two dimension (b) Three dimension.
(a) (b)
Fig. 3: Axial velocity π’ versus π§- direction for different values of Eyring-
Powell fluid parameterπ΄,and with fixed values of parameters {πΈ1 = 0.1, πΈ2 =0.2, πΈ3 = 0.3, πΈ4 = 0.1, πΈ5 = 0.2, π1 = 0.9, π = 0.8, π = 1, π½1 = 0.02, π =0.09, π₯ = 0.02, π‘ = 0.01, π¦ = 0} in (a) Two dimension (b) Three dimension.
"E10.1 "
"E10.5 "
"E10.9 "
1.0 0.5 0.0 0.5 1.0
1524.6
1524.8
1525.0
1525.2
1525.4
1525.6
z
u
"E30.1 "
"E30.15 "
E30.2 "
1.0 0.5 0.0 0.5 1.0
1524.5
1525.0
1525.5
1526.0
1526.5
z
u
A2 "
A4"
A6"
1.0 0.5 0.0 0.5 1.0
1525
1526
1527
1528
1529
z
u
International Journal of Pure and Applied Mathematics Special Issue
280
(a) (b)
Fig. 4: Axial velocity π’ versus π§- direction for different values of Eyring-
Powell fluid parameterπ1,and with fixed values of parameters {πΈ1 =0.1, πΈ2 = 0.2, πΈ3 = 0.3, πΈ4 = 0.1, πΈ5 = 0.2, π΄ = 0.9, π = 0.8, π = 1, π½1 =0.02, π = 0.09, π₯ = 0.02, π‘ = 0.01, π¦ = 0} in (a) Two dimension (b) Three
dimension.
(a) (b)
Fig. 5: Axial velocity π’ versus π§- direction for different values of Hartman
numberπ,and with fixed values of parameters {πΈ1 = 0.1, πΈ2 = 0.2, πΈ3 =0.3, πΈ4 = 0.1, πΈ5 = 0.2, π΄ = 0.9, π1 = 0.8, π = 1, π½1 = 0.02, π = 0.09, π₯ =0.02, π‘ = 0.01, π¦ = 0} in (a) Two dimension (b) Three dimension.
(a) (b)
Fig. 6: Axial velocity π’ versus π§- direction for different values of porosity
parameter π,and with fixed values of parameters {πΈ1 = 0.1, πΈ2 = 0.2, πΈ3 =0.3, πΈ4 = 0.1, πΈ5 = 0.2, π΄ = 0.9, π1 = 0.8, π = 0.8, π½1 = 0.02, π =0.09, π₯ = 0.02, π‘ = 0.01, π¦ = 0} in (a) Two dimension (b) Three dimension.
Trapping Mechanism
Trapping phenomena is also an important part of peristaltic motion which is a
formation of an inside moving bolus that are bounded by multiple streamlines.
For this purpose, Figs.(7)-(10) are drawn for multiple values of important
"W10.9 "
"W11.9 "
"W12.9 "
1.0 0.5 0.0 0.5 1.0
1524.6
1524.8
1525.0
1525.2
1525.4
1525.6
1525.8
z
u
M0.01 "
M0.012 "
M0.013 "
1.0 0.5 0.0 0.5 1.0
2500.0
2500.5
2501.0
z
u
k0.1 "
k0.2 "
k0.3 "
1.0 0.5 0.0 0.5 1.0
806
808
810
812
z
u
International Journal of Pure and Applied Mathematics Special Issue
281
parameters that impact on the trapping streamlines. From Fig.(7) we deduced
that grown up ofπ΄magnitude causes two opposite effect on the trapping bolus
i.e. the magnitude of the bolus in the left side of the plane β0.7 < π₯ β€β0.4 increase while the right side of the plane for β0.2 < π₯ β€ 0.27 decreases
in diameter and number. The streamlines pattern for multiple values of
Hartman number π are plotted in Fig.(8). It is found that for ascending values
of π, the trapping bolus reduces in size and more bolus create. The influence of
porosity parameter π on the trapping bolus is seen in Fig.(9). It can be observed
that the diameter of trapped bolus rapidly increases with arising of π magnitude.
Fig.(10) depicted that the volume of the bolus decrease but more boluscreate
when the values of aspect ratio π½1 increase.
(a) (b)
Fig. 7: Streamlines for different values of Eyring-Powell parameterπ΄,and with
fixed values of parameters πΈ1 = 0.1, πΈ2 = 0.3πΈ3 = 0.1, πΈ4 = 0.2, πΈ5 =
0.3, π1 = 0.8, π = 0.8, π½1 = 0.2, π = 1, π =Ο
9, π‘ = 0.25, π¦ = 0.1 (a) π΄ =
0.9(b)π΄ = 1.9 .
(a) (b)
Fig. 8: Streamlines for different values of Hartman numberπ,and with fixed
values of parameters πΈ1 = 0.1, πΈ2 = 0.3πΈ3 = 0.1, πΈ4 = 0.2, πΈ5 = 0.3, π΄ =
0.8, π1 = 0.8, π½1 = 0.2, π = 1, π =Ο
9, π‘ = 0.25, π¦ = 0.1 (a) π = 0.2(b)π =
1 .
International Journal of Pure and Applied Mathematics Special Issue
282
(a) (b)
Fig. 9: Streamlines for different values of porosity parameter π,and with fixed
values of parameters πΈ1 = 0.1, πΈ2 = 0.3πΈ3 = 0.1, πΈ4 = 0.2, πΈ5 = 0.3, π΄ =
0.8, π1 = 0.8, π½1 = 0.2, π = 0.9, π =Ο
9, π‘ = 0.25, π¦ = 0.1 (a) π = 0.2(b)π =
1 .
(a) (b)
Fig. 10: Streamlines for different values of aspect ratio parameterπ½1,and with
fixed values of parameters πΈ1 = 0.1, πΈ2 = 0.3πΈ3 = 0.1, πΈ4 = 0.2, πΈ5 =
0.3, π΄ = 0.8, π1 = 0.8, π = 0.2, π = 0.9, π =Ο
9, π‘ = 0.25, π¦ = 0.1 (a)π½1 =
0.7(b)π½1 = 0.9 .
5. Conclusion
In this paper, a mathematical model of the peristaltic transport of Eyring-Powell
fluid flows in a three dimensional rectangular duct with porous medium under
the influence of magnetic field has been investigated. No- slip velocity
International Journal of Pure and Applied Mathematics Special Issue
283
condition and wall properties are taken into account. A long- wavelength and
low-Renolds number approximations are employed to simplify the governing
equation into a high non-linear partial differential equation and by solving the
resulted equation using homotopy perturbation method (HPM), the series
solution of velocity field is found. In this chapter the scope and applicability of
earlier results given by Riaz et al.[5] was extended to effect of magnetic field
and porous medium. The main results and conclusions of this investigation are
summarized as follows:
The velocity axial is an increasing function with ascending values of
viscos damping πΈ3, and decreasing function with wall rigidity πΈ1.
Totally opposite impact for the Eyring-Powell parameters π΄ and π1 on
the velocity profile is noticed, enhancement of the first one increase the
velocity profile while for ascending values of the second parameter
reduces the velocity.
The trapped bolus decreases in magnitude but enclosed by more
streamlines due enhancement of aspect ratioπ½1values.
Enhancement of the Hartman number has a reduction effect on the
trapped bolus magnitude however bolus' number increases in the right
side of the plane only.
The flow characterization (velocity profile and streamlines) are very
sensitive against a very little variation of porosity and aspect ratio
parameters π, π½1respectively.
References
[1] J.H. He, Homotopy perturbation technique, Comp. Meth. Appl. Mech. Eng. 178 (1999) 257_262.
[2] J.H. He, A coupling method of homotopy technique and a perturbation technique for non- linear problems, Int. J. Non -linear Mech. 35 (2000) 37_43.
[3] E. Babolian, A. Azizi, J. Saeidian"Some notes on using the homotopy perturbation method for solving time-dependent differential equations"J.Mathematical and Computer Modelling,50, (2009),pp. 213-224.
[4] M. Ali Abbas , Y.Q. Bai , M.M. Bhatti , M.M. Rashidi ,"Three dimensional peristaltic flow of hyperbolic tangent fluid in non-uniform channel having flexible walls"Alexandria Engineering Journal, (2016), 55, 653β662.
[5] Arshad Riaz, R. Ellahi , S. Nadeem"Peristaltic transport of a Carreau fluid in a compliant rectangular duct "Alexandria Engineering Journal, (2014) ,53, 475β484.
[6] S. Nadeem , Arshad Riaz , R. Ellahi ,N. S. Akbar," Mathematical model for the peristaltic flow of Jeffrey fluid with nanoparticles
International Journal of Pure and Applied Mathematics Special Issue
284
phenomenon through a rectangular duct"Appl Nanosci J, (2014) 4,613β624.
[7] Ahmet Yidirm , S. A. Sezer,"Effects of partial slip on the peristaltic flow of a MHD Newtonian fluid in an asymmetric channel"Mathematical and Computer Modelling J, 52, (2010),pp. 618-625.
[8] Rahmat Ellahi , Arshad Riaz , S. Nadeem ,"A theoretical study of Prandtl nanofluid in a rectangular duct through peristaltic transport", Appl. Nanosci ,(2014), 4,pp.753β760.
[9] R. Ellahi, Arshad Riaz, S. Nadeem, and M. Ali,"Peristaltic Flow of Carreau Fluid in a Rectangular Duct through a Porous Medium"Hindawi Publishing Corporation,Math. Prob. Eng,doi:10.1155/2012/329639.
[10] Arshad Riaz,S. Nadeem,R. Ellahi,"Effects of the wall properties on unsteadyperistaltic flow of an Eyring- Powell fluid in a three-dimensional rectangular duct",8 (6), (2015), 1550081 (17 pages).
[11] MVS. Reddy, M. Mishra, S. Sreenadh, AR. Rao," Influence of lateral walls on peristaltic flow in a rectangular duct", J. Fluids Eng, 127, PP. 824-827,(2005).
[12] KhS. Mekheimer, SZ. Husseny, AI. Abdellateef," Effect of lateral walls on peristaltic flow through a symmetric rectangular duct", Appl. Bion. Biomech,8,PP.295-308,(2011).
[13] R. Ellahi, M.M. Bhatti, A. A. Khan," Mathematical analysis of peristaltic transport of an Eyring-Powell fluid through a porous rectangular duct", J. Wulfenia, 22(1),PP. 266-283,(2015).
[14] S. Akram, Kh.S. Mekheimer, S. Nadeem," Influence of lateral walls on peristaltic flow of a couple stress fluid in a non-uniform rectangular duct", Appl. Math. Inf. Sci., 8,PP. 1127-1133,(2014).
[15] R. Ellahi, M. M. Bhatti, K. Vafai," Effects of heat and mass transfer on peristaltic flow in a non- uniform rectangular duct", Int.J. Heat Mass Transfer, 71, PP. 706-719,(2014).
[16] R. Ellahi, M.M. Bhatti, C. M. Khalique," Three- dimensional flow analysis of Carreau fluid model induced by peristaltic wave in the presence of magnetic field", J. Molecular Liquids, 241,PP. 1059-1068,(2017).
International Journal of Pure and Applied Mathematics Special Issue
285
286