The Medium Breaker range - DEMOLITION TECHNOLOGIES
Transcript of The Medium Breaker range - DEMOLITION TECHNOLOGIES
�
Atlas Copco’s range of medium-duty hydraulic breakers was developed for a wide variety of applications. The com-bined gas/oil power principle means they are both powerful and highly flexible with regard to oil flow rate and pressure. Their technically advanced percussion mechanisms, e.g. with long piston stroke, reduce unavoidable vibrations far more efficiently than many other makes. Our Medium Breakers are ideal for road work, trenching, general demolition, and primary and secondary rock breaking.
These medium-duty hydraulic breakers are also at home reducing demolition rubble for feeding to recycling plants, and in all other jobs which call for a robust design, reliability and long life.
Both their general versatility and their compatibility with a broad spectrum of carriers make these breakers genuine all-rounders.
Installed as standard: 4 decades of experience in percussion technology
�
Convincing technology for tough jobs
Constant impact energy whatever the oil flow rate The Medium Breakers are powered by a combination of oil and gas (nitrogen). 70% of the impact energy is generated by gas power, which means that the breakers are virtually independent of the hydraulic supply from the carrier.
Dependable and low on service thanks to simple design There are only three moving parts: • the percussion piston • the control valve • the pilot valve
Routine maintenance takes only a matter of minutes.
Robust and stableThe breakers in the medium-duty series have robust and stable guide systems to handle the jobs involved. Exposed areas are made from highly wear-resistant materials to mini-mize wear.
Less strain on man and machineThe long piston stroke and the vibration and noise-insulated mounting of the percussion mechanism mean that the Medium Breakers run very smoothly and quietly.
Field Type of application MB
500
MB
700
MB
100
0M
B 1
�00
MB
170
0
General construction work
Tearing up concrete and asphalt road surfaces • • • •
Landscape gardening and landscaping •
Trenchwork for utilities, foundation work • • • • •
Demolition
Masonry and non-reinforced concrete • • • •
Reinforced concrete • • • •
Heavily reinforced concrete, demolition of power stations and bridges •
Rock mining/bre-aking
Primary breaking •
Secondary breaking, bench leveling, trenchwork, foundation work • • •
Tunneling*, mining*
Roof clearing • • • • •
Bench leveling • • • • •
Tunnel driving •
High-tem-perature applications*
Removing encrustations • • • •
Breaking out ladles and molds • • • •
Breaking up slag •
Underwater applications*
Demolition Deepening shipping channels • •
Service weight of carrier in metric tons
5 10 15 �0 �5 �0 �5 40 45
MB 500
MB 700
MB 1000
MB 1200
MB 1700
* = after prior consultation with Atlas Copco
4
www.atlascopco.comTh
e fa
ce o
f in
nova
tion
High durability thanks to effective dust protection On job sites with particularly high dust loads, e.g. tunneling and overhead demo-lition work, fitting the hydraulic breaker with the DustProtector system has proved invaluable. A combination of several strip-pers reliably prevents abrasive rock dust and other foreign bodies from penetrating the lower breaker section, protecting the percussion mechanism from damage and avoiding premature wear to the bushings. DustProtector is available as an optional extra on models MB 700, MB 1000, MB 1�00 and MB 1700.
Reliable lubrication – life insurance for any breaker The ContiLube® II automatic lube unit ensures the optimum, cost-effective lubri-cation of the breaker. Mounted directly on the hydraulic breaker, the system is easy to set, use and monitor. The cartridges contain 500 g of high-viscosity chisel paste. ContiLube® II is fitted as stand-ard on the MB 700, MB 1000, MB 1�00, MB 1700 breakers, and is available as an optional extra for the MB 500 model.
Advantages: • Compact- self-priming pump, delivers
chisel paste only when needed for opti-mized consumption
• Positioned directly on the breaker, the unit is self-sufficient, easy to access, dispenses with the need for long con-necting hoses and allows the carrier operator to monitor paste levels at all times
• All ports are protected inside the breaker box
• Cartridges can be changed quickly with-out the need for tools (screw fit)
• Cartridges are available worldwide and are refillable
Extras every breaker should have
DustProtector II Dust protection system of the hydraulic breaker
Reusable sleeve – can be reused several times when wear bushings are replaced. Highly resistant to grease and mechanical loads
Reusable sleeve
ContiLube® IIAutomatic lubrication unit mounted directly on the breaker
5
Modern breakers are gentle on the environment but tough on rock
Effective noise and vibration damping as standard The VibroSilenced system is a highly effective arrangement of elastic damping elements which isolate the percussion mechanism acoustically from the external guide system. It is no coincidence that Atlas Copco breakers are among the quietest on the market. Moreover, the VibroSilenced system prevents damaging vibrations which could otherwise be detrimental to both carrier and operator. All Medium Breaker models are fitted with the VibroSilenced system as standard.
Maximum productivity through optimized impact energyThe AutoControl automatic stroke-switching system opti-mizes the ratio of impact energy to impact rate so as to maximize percussive performance at all times. (Percussive performance = impact energy x impact rate). Soft material: lower impact energy, higher impact rate = max. percussive performanceHard material: maximum impact energy, reduced impact rate = max. percussive performance
AutoControl avoids blank firing and reduces the load on both carrier and hydraulic breaker (by reducing energy in the event of blank firing)
AutoControl always starts the breaker in short-stroke mode – reduced energy permits reliable centering.
AutoControl ensures maximum energy recovery from each blow and thus enhances output without increasing hydraulic input.
AutoControl guarantees maximum efficiency and smooth running.
�
Perfect handling ensures maximum productivityThe “StartSelect” system allows the start-up and shut-off behavior of the breaker to be set in line with conditions.
“AutoStart” modefor jobs in unstable ground, such as:
• secondary reduction of mined rock• working horizontally or overhead• breaking light concrete structures
“AutoStop” modefor jobs on firm ground such as:
• trenching • bench leveling in the quarry • excavating foundations in rock • breaking heavy concrete structures
Perfect handling for perfect results
Long stroke
Short stroke
Impact level
Pis
ton
str
oke
[%]
Long stroke
Short stroke
Impact level
Pis
ton
str
oke
[%]
AutoStart – for jobs in unstable ground
AutoStop – for jobs on firm ground
7
MB-hydraulic breakers MB 500 MB 700 MB 1000 MB 1200 MB 1700
Carrier weight class 1) t 8-15 10-18 1�-�0 15-�� 18-�4
Service weight �) kg 550 750 1000 1�00 1700
Oil flow rate l/min �0-100 80-1�0 85-1�0 100-140 1�0-1�0
Operating pressure bar 1�0-1�0 140-170 1�0-180 1�0-180 1�0-180
Blow frequency bpm 440-1000 �70-800 �50-750 �40-�80 ��0-�00
Stroke-length switching - - Auto Control Auto Control Auto Control
Start-up mode AutoStop AutoStart AutoStart StartSelect StartSelect
Working tool diameter mm 90 100 110 1�0 140
Useful length of tool mm 450 550 570 �05 �50
Pt.-Id. No. ���� 0901 87 - - - -
Equipped with ContiLube® II
Pt.-Id. No. ���� 0895 09 ���� 09�8 95 ���� 0887 85 ���� 0904 41 ���� 0904 49
Equipped with DustProtector
Useful length of tool mm - 510 540 580 ��5
Pt.-Id. No. - ���� 09�8 97 ���� 0887 87 ���� 0904 4� ���� 0904 51
1) Weights apply to standard carriers only. Any variances must be agreed with Atlas Copco and/or the carrier manufacturer prior to attachment.
�) Breaker and breaker box with standard adapter plus working tool.
GENUINEPA
RT
S•
AC
CESSORIES•WORKIN
GT
OO
LS
•SE
RVICE •
��90
051
5 01
©
�00
�, A
tlas
Cop
co C
onst
ruct
ion
Tool
s G
mbH
, Ess
en, G
erm
any.
Sub
ject
to
tech
nica
l mod
ifica
tions
.
Blunt toolfor primary and secondary rock breaking
Use only authorized parts. Any damage or malfunction caused by the use of unauthorized parts is not covered by Warranty or Product Liability.
www.atlascopco.com/cto
Chiselfor rock breaking and demolition work
Moil point for multi-purpose use
Total length P-Line T-Line
in mm
MB 500 ��00 ���0 ���� 94 ���0 ���� 94
MB 500 �800 ���� 0859 47 ���� 0859 47
MB 700 ��00 ���0 99�� 40 ���0 99�� 40
MB 700 �800 ���1 85�8 59 ���1 85�8 59
MB 1000 ��00 ���0 99�� 40 ���0 99�� 40
MB 1000 �800 ���1 85�8 59 ���1 85�8 59
MB 1200 ��00 ���0 99�� 40 ���0 99�� 40
MB 1200 �800 ���1 85�8 59 ���1 85�8 59
MB 1700 ��00 ���� 0870 15 ���� 0870 15
MB 1700 �800 ���� 0870 1� ���� 0870 1�
Moil point Chisel (cross) Chisel (parallel) Blunt tool
Standard length Standard length Standard length Standard length
MB 500 ���� ��55 �5 ���� ��84 45 - ���� 0�54 71
MB 700 ���� 0�87 05 ���� 0�87 07 - ���� 0944 48
MB 1000 ���� 0848 77 ���� 0848 87 ���� 094� 51 ���� 0901 1�
MB 1200 ���� 08�7 87 ���� 08�9 4� ���� 094� 5� ���� 08�9 45
MB 1700 ���� 08�� �5 ���� 08�� �7 ���� 094� 5� ���� 08�� �9
Description Remarks Pt.-Id. No.
Service box No. I with nitrogen cylinder � l ���� 0898 44
Service box No. II with nitrogen cylinder 5 l ���� 0898 45
Service box No. III without nitrogen bottle ���� 0949 40
Don’t compromise on productivity
Tools for every jobToday’s hydraulic breakers offer a significantly improved ratio of percussive performance to weight, which in turn imposes far greater loads on all breaker components. The dimensions, material properties and tip geometry of work-ing tools have a major impact on reliability, wear behavior, performance and productivity.
Genuine working tools from Atlas Copco are made from a special alloy that has been optimized for hydraulic breaker applications. A complex heat treatment process and strict quality control at all stages of production in our own facili-ties guarantee maximum durability.
Working tools may look just like a piece of steel, but they are the result of a long and complex development process backed by extensive experience in the field.
So do not take any risks. Only genuine working tools will ensure that your Atlas Copco breaker remains the unit that you bought: a reliable, safe production unit good for many millions of impacts.
Connection hosesGenuine Atlas Copco hoses are designed to with-stand the strains of demolition work and are available in a standard and special length. The hose material is protected against chafing by a spiral steel wire. Special screw couplings allow the hoses to be attached to all industrial carriers.
Service boxes