The Barton Catalogue - Emotion Yachting · The Barton Catalogue Barton Marine Equipment Limited...
Transcript of The Barton Catalogue - Emotion Yachting · The Barton Catalogue Barton Marine Equipment Limited...
The Barton Catalogue
Barton Marine Equipment Limited
Marine House · Tyler Way · Whitstable · Kent CT5 2RS UK
t +44 (0)1227 792979
f +44 (0)1227 793555
www.bartonmarine.com
www.bartonmarine.com
new
pro
duc
ts Welcome to the new Barton catalogue...At Barton we have continued to improve and widen our choice of product lines.
All of our products are now supplied on attractive backing cards which give full technicaldetails of each item. These include details of safe working loads, maximum line capacities,recommended boat sizes and much more.
We have also included more complete packaged kits for mainsheettravellers, the Boomstrut and lazy jacks to name a few. All the partsrequired together with full fitting instructions are provided in each kit.
New products featured in this catalogue include:DO 550 rope clutches – not only good looking, but a completelynew design to incorporate the latest materials and manufacturingprocesses. Details on page 39.
Backstay tensioner blocks in high load stainless steel.Suitable for yachts with split backstays. Details on page 19.
Fuel Whistle – an environmentally friendly new product that preventsfuel spills when refuelling. This not only keeps your boat clean, buthelps to prevent pollution. Details on page 52.
The award-winning, patented ClamSeal™ – a glue-less repairsystem that instantly repairs small tears or splits in inflatables above orbelow the waterline – regardless of the fact that the material may be wet.Details on page 51.
Our Barton Merchandiser Racks have been updated to bring them in line with our new packaging. This year a newcompact version has been introduced for the smaller chandler that may be limited for space.
The Barton website continues to expand and holds a far greater breadth of technical information than can be containedin this catalogue. Visit us at www.bartonmarine.com to help with your choice of the best product to suit yourrequirements, or we would be pleased to take your telephone call for any information or advice on our products.
Our new home, pictured below, continues to make us more efficient and allow for continued expansionand product development.
We are proud to be based in Whitstable, Kent, UK and from here supply our growing global customer base.
1
contents
www.bartonmarine.com
The Barton Catalogue – contentsBarton Boomstrut .................................................................................................................................................................page 4Blocks
Size 1 (30mm sheave) standard blocks..............................................................................................page 5Size 2 (35mm sheave) standard blocks .....................................................................................pages 6-7Size 3 (45mm sheave) standard blocks .....................................................................................pages 8-9Size 4 (58mm sheave) standard blocks..............................................................................pages 10-11Size 5 (54mm sheave) cruiser blocks ...................................................................................pages 12-13Size 6 (64mm sheave) cruiser blocks ...................................................................................pages 14-15Size 7 (70mm sheave) cruiser blocks ...................................................................................pages 16-17Stainless steel blocks...................................................................................................................................page 18Wire rope blocks ...........................................................................................................................................page 19Snatch blocks...................................................................................................................................................page 20High load & foot blocks............................................................................................................................page 21
Track & travellers – recirculating ball bearing systems
Recirculating ball bearing mainsheet & genoa traveller systems .......................pages 22-29Complete pack mainsheet traveller systems................................................................................page 24Modular components.................................................................................................................................page 25Travellers – single take off .......................................................................................................................page 26Travellers - double take off .....................................................................................................................page 27End fittings........................................................................................................................................................page 28Track; drilled, sliding bolt and beam................................................................................................page 29
‘I’ track & travellers
19mm ‘I’ track & travellers .....................................................................................................................page 3024mm ‘I’ track & travellers .....................................................................................................................page 3128mm ‘I’ track & travellers .....................................................................................................................page 32
‘T’ track genoa cars and accessories
20mm ‘T’ track genoa cars ....................................................................................................................page 3325mm ‘T’ track genoa cars........................................................................................................pages 34-3532mm ‘T’ track genoa cars........................................................................................................pages 36-37
Deck organiser blocks.....................................................................................................................................................page 38DO 550 clutches.................................................................................................................................................................page 39Winch handles ....................................................................................................................................................................page 40Barton composite winches and the Barton ‘Wincher’ ..............................................................................page 41Sail Handling
– lazy jack kits; reefing kits, gooseneck hooks, mast steps ..................................pages 42-43Special cleats & Barton Line Tamer ........................................................................................................................page 44Fairleads, cleats & thimbles ........................................................................................................................................page 45Dinghy & dayboat fittings ...........................................................................................................................................page 46Tiller extensions ..................................................................................................................................................................page 47‘K’ cam cleats.......................................................................................................................................................................page 48Dinghy mast support ......................................................................................................................................................page 49Inspection covers ...............................................................................................................................................................page 50Barton ClamSeal™ ............................................................................................................................................................page 51Barton Fuel Whistle..........................................................................................................................................................page 52Bullseyes, pad eyes & deck eyes...............................................................................................................................page 53Clevis pins, split pins, springs & sheaves............................................................................................................page 54Shackles & ‘S’ hooks .......................................................................................................................................................page 55Part number index ............................................................................................................................................................page 56
The Barton Ball Bearing OptionAll Barton blocks from size 1 to size 7 offer the
option of a high-performance, low-friction ballbearing sheave version. Our design features
twin rows of acetal balls running on a largediameter centre boss. This enables theload bearing surface to be maximised overthe greatest number of bearings, givinghigher performance in all directions.
Ball bearing blocks to the unique Bartondesign bring you the possibility of upgrading
your block systems at a realistic cost.
Barton blocks – a comprehensive rangeto suit every requirement
www.bartonmarine.com
ab
out b
lock
s
2
Barton blocks
Fixed EyeClevis PinA simple, low-priced fixedeye block with removableclevis pin for attachment.
Fixed EyeWith a plainattachment eye.
Reverse ShackleRemovable shackle thatcan be set in-line or at90° to the sheave.
SwivelFully swivelling head withremovable shackle.
Snap ShackleWith a cast stainlesssteel swivelling snapshackle – ideal forquick-release downhaulsor vang tackles.
BecketAll the appropriateblocks are availablewith or without becket.
A wide range of attachment heads areavailable on Barton blocks, including:
Probably one of the most comprehensive ranges of blocks available from anymanufacturer – these compact, high strength products are manufactured from the most
modern materials and are suitable for use on dinghies, dayboats, cruising and racing yachts.
Designed for high performance, strength and light weight, these products provide maximumefficiency and a long working life.
With sheaves ranging from 30mm to 85mm, safe working loads up to 2700kg, rope capacity up to 14mm and a widevariety of sheave permutations, you are sure to find the right product to suit your requirements.
Although we madeour name worldwidewith the design andmanufacture ofblocks, at Barton ourongoing programmeof R&D means wehave developed amuch wider range of state-of-the-art deck hardware.
From complete packaged mainsheet systems to genoa track andtravellers, the 2008 Barton range covers virtually all your deckrigging requirements, and more.
See page 39 of this new catalogue for details of our brand newclutch – available in single, double and triple and ideal for cruisingor racing yachts.
Variloc Multi HeadAllows swivel to be locked at30° positions in relation tosheave. Inverting the plasticlocking piece converts toswivel mode. Supplied withscrew pin strip shackle.
Barton PlainBearing BlocksAll Barton plain bearing blocks have aprecision moulded acetal sheave running a
large diameter brass bearing, ensuring freerunning under the highest of loads.
We don’t just make blocks...
3control the power
ab
out blocks
Barton blocks
Some tips when selectingand fitting blocks...• Choose carefully, ensuring the block is strong
enough for the job required. Rope capacitydoes not denote strength.
• Check line capacity is sufficient. A tight fitwill cause friction, side plate and line wear.
• Always ensure a fair lead. Blocks are designedto run at maximum load bearing and efficiencywith the load running directly through thecentral axis.
• Never load one sheave of a double block.This will cause the block to fall to one sideand create side plate and line wear.
• When fitting blocks to the masthead alwaysensure that there is sufficient articulation.
• When fitting mainsheet cam cleat blocks,ensure that the cam cleat is set at the correctangle to allow easy release in an emergency.
• Foot blocks & cheek blocks should always bethrough-bolted for maximum strength.
Care of blocks and deck fittings...• Regularly rinse blocks and deck fittings
with fresh water to remove salt.
• Ensure that sheaves run freely.
• Check all masthead blocks on a regular basis.
• Check shackles for signs of strain or overload.
• Inspect cam cleats (where fitted) forexcessive wear.
The comprehensiveBarton range includes:
• Single
• Single & cam cleat
• Double
• Triple
• Triple & cam cleat
• Fiddle
• Fiddle & cam cleat
• Snatch blocks
• Foot blocks
• Foot blocks with jamming cam
• High load blocks
• Wire sheave blocks.
control the power4
boo
mst
rut
Barton Boomstrut
*The maximum amount the boomstrut rods can beshortened to fit inside the vang area.
** The maximum amount of available pin-to-pin travelwhen flexed.
*** The downward force the boomstrut will support atthe point of the boom fitting attachment.
These are approximate measurements which may varydepending on boat type.
Max Max Maxpin-to-pin rods can be initial full stroke at full
Suggested boat length (m) Part length reduced by* adjustment** adjustment Force***No. mm mm mm mm kg
Barton BoomstrutUp to 6.0m 44 010 960 150 300 150 90
6.0m to 7.5m 44 020 1070 150 300 150 140
7.5m to 9.0m 44 030 1180 150 300 150 185
9.0m to 10.5m 44 035 1320 150 400 200 230
10.5m to 12m 44 040 1450 150 400 200 270
Boomstrutextended
Boomstrutcompressed
• Five sizes to suit yachts up to 12m/40ft LOA
• Patented flexing spring provides fast responseand a constant force for vang efficiencyThe boomstrut’s lightweight, low-profile design featurestwo flexible coated fibreglass rods which provide the forceto support the boom. Pulling the boom down with aconventional kicker causes the Boomstrut to flex upwards;releasing straightens the rods, thereby lifting andsupporting the boom.
• Maintenance-free, durable designEliminates friction and sliding parts.
• Improved performanceLess weight and windage.
• Easy installationThere’s no need to replace your existing hardware – theBoomstrut mounts independently inside the existingkicking strap tackle.
• Simple-to-follow instructionsThe Boomstrut is supplied with complete fitting instructionsand more comprehensive details are available on ourwebsite, www.bartonmarine.com.
• Mast fitting can use existing luff grooveTo eliminate drilling, the Boomstrut’s mast bracketcan be slotted into your mast’s luff groove.
• Contoured boom fittingThe Boomstrut’s boom bracket is contoured to fit bothround and flat boom profiles.
• Carefully designed & constructedThe Barton Boomstrut has been carefully designed andconstructed to eliminate sharp edges, minimise parts andprovide trouble-free installation and use.
All parts are from high-grade stainless steel and Spectrogrey anodised aluminium for good looks and durability.
You’ll find many reasons to appreciate theBarton Boomstrut – no more topping lift hassles,
no adjustments and no hang-ups – neveragain will your boom fall
accidentally.
Back-to-back swivelA useful doubleswivelling blockwith a variety ofapplications,especially dinghymainsheet/horse blocks.
Plain Ball-bearing Length Weight (g)sheave sheave mm plain ball
Single size 1 blocksSingle – fixed eye clevis pin 01 090 11 090 78 48 46
Single – fixed eye clevis pin + becket 01 091 11 091 87 52 51
Single – fixed eye 01 110 11 110 70 41 40
Single – fixed eye + becket 01 111 11 111 80 46 44
Single – reverse shackle 01 120 11 120 82 51 49
Single – reverse shackle + becket 01 121 11 121 93 56 55
Single – swivel 01 130 11 130 85 57 55
Single – swivel + becket 01 131 11 131 98 61 60
Single – upright 01 150 11 150 53 64 62
Single – upright with fairlead 01 151 11 151 63 70 78
Lightweight cheek block 01 160 11 160 55 21 20
Single – stand up block 01 170 11 170 79 62 60
Single – spinnaker lead 01 180 11 180 114 59 57
Lightweight lead block 01 190 11 190 44 20 18
Double size 1 blocksDouble – fixed eye 01 210 11 210 69 65 63
Double – fixed eye + becket 01 211 11 211 78 71 69
Double – reverse shackle 01 220 11 220 83 77 73
Double – reverse shackle + becket 01 221 11 221 91 82 78
Double – swivel 01 230 11 230 90 83 80
Double – swivel + becket 01 231 11 231 99 88 85
Double – upright 01 250 11 250 53 89 86
Back to back swivel 01 280 11 280 118 81 78
Triple size 1 blocksTriple – reverse shackle 01 320 11 320 81 102 97
Triple – reverse shackle + becket 01 321 11 321 94 109 103
Triple – swivel 01 330 11 330 85 108 103
Triple – swivel + becket 01 331 11 331 98 112 108
5www.bartonmarine.com
size 1 blocks
30mm standard blocks
Fixed EyeClevis PinA simple, low-priced fixedeye block with removableclevis pin for attachment.Pin Ø 5mm. Widthbetween straps 13mm.
Fixed EyeWith a plainattachment eye.
Reverse ShackleRemovable shackle thatcan be set in-line or at90° to the sheave.
SwivelFully swivelling headwith removable shackle.
BecketAll the appropriate size1 blocks are availablewith or without becket.
A strong, lightweight range of blocks for use on dinghiesand dayboats or as lead blocks on larger craft.
All available with plain or ball bearing sheaves:
Ball bearing blocksWith our unique super-low friction ball racesystems, featuring acetal sheaves and delrin ballbearings, running on a large diameter centreboss. This allows us to fit more load-bearingballs, which ensure extremely low frictionperformance, even under high loads.
Plain bearing blocksBarton plain bearing blocks have a precisionmoulded acetal sheave running on a largediameter brass bearing, ensuring freerunning under the highest of loads.
Sheave size 30mm x 11mm (13/16 x 7/16”)
Important note – break loads:Where break and safe working loads are stated,it is assumed that all sheaves are evenly loadedas in a purchase tackle. Uneven loading, orloading of one sheave in a double or tripleblock, will severely effect strength quoted.If unsure, please seek further advice.
Maximum rolling load on ball bearing blocksis the maximum free running load beforeball bearings will distort.
Available with these heads and shackles...
SWL350kg (771lbs)
Max rolling load(ball bearing blocks)245kg (540lbs)
Max rope diameter
8mm (5/16”)
Break load700kg (1543lbs)
01 090 01 130
UprightWith or without fairlead.
Fairlead prevents linefalling away whennot under load.
Fastenings 5mm.
01 150
01 151
01 160Lightweight leadA handy lightweight blockfor use where high load isnot expected.
01 190
01 170
Spinnaker leadA useful block
mounted on astainless steel tang.
Fastenings 5mm.
01 280
01 230
01 250
01 330
01 180
Cam cleat blocksFitted with Kevlar ‘K’ cams
(unless otherwise stated).Cam arms are fullyadjustable by movingthe locking clevis pinto achieve the correct
cleating angle. Used inconjunction with the relevant
top block, this range of blocks isparticularly useful for mainsheet,vang tackles or downhauls ondinghies, dayboats or lightcruising yachts.
Fixed EyeClevis PinA simple, low-priced fixedeye block with removableclevis pin for attachment.Pin Ø 5mm. Widthbetween straps 13mm.
Fixed EyeWith a plainattachment eye.
Reverse ShackleRemovable shackle thatcan be set in-line or at90° to the sheave.
SwivelFully swivelling headwith removable shackle.
Snap ShackleWith a cast stainless steelswivelling snap shackle.Ideal for quick-releasedownhauls or vang tackles.
BecketAll the appropriate size 2blocks are available withor without becket.
Stand upFeatures aflexible plasticspring for anti-tumble action.Base Ø 58mm.
Fastenings5mm.
02 150
02 170
02 130
Stanchion leadDesigned for use
on 25mm Ø tubes,with a swivelling
action with up-downmovement allowing
for a fair lead oncontrol lines.
Note: A larger size 3should be used for
final take off onfurling lines.
UprightWith orwithout fairlead.
Fairlead preventsline falling awaywhen notunder load.
Fastenings 5mm.
02 161
02 571
www.bartonmarine.com
size
2 b
lock
s A strong, lightweight range of blocks for use on dinghiesand dayboats or as lead blocks on larger boats.
A comprehensive range of multiple sheave options,together with fiddles and cam cleat blocks, allowpowerful, lightweight tackles to be achieved.
Sheave size
Single 35mm x 11mm (13/8 x 7/16”)
Fiddle 30/45mm x 11mm (13/16 ” /13/4” x 7/16”)
Important note – break loads:Where break and safe working loads are stated, it is assumed that all sheaves are evenlyloaded as in a purchase tackle. Uneven loading, or loading of one sheave in a double ortriple block, will severely effect strength quoted. If unsure, please seek further advice.
Maximum rolling load on ball bearing blocks is the maximum free running load beforeball bearings will distort.Available with these heads and shackles...
6
02 151
02 190
SWL
370kg (815lbs)
Max rolling load(ball bearing blocks)
260kg (573lbs)
Max rope diameter
8mm (5/16”)
Break load
740kg (1630lbs)
02 140Back-to-backswivel
A useful doubleswivelling block
with a variety ofapplications,
especially dinghymainsheet/
horse blocks.
02 280
Spinnaker leadA useful block
mounted on astainless steel tang.
Fastenings 5mm.
02 180
02 160
CheekWith a plastic
backing platestandard –
curved backingplate also
available (02161),to allow snug
attachment to spars etc.
Base size 79mm x 43mm.Fastenings 5mm.
35mm standard blocksAll available with plain or ball bearing sheaves:
Ball bearing blocksWith our unique super-low friction ball racesystems, featuring acetal sheaves and delrin ballbearings, running on a large diameter centreboss. This allows us to fit more load-bearingballs, which ensure extremely low frictionperformance, even under high loads.
Plain bearing blocksBarton plain bearing blocks have a precisionmoulded acetal sheave running on a largediameter brass bearing, ensuring freerunning under the highest of loads.
7
Plain Ball-bearing Length Weight (g)sheave sheave mm plain ball
Single size 2 blocks
Single – fixed eye clevis pin 02 090 12 090 87 56 54
Single – fixed eye clevis pin + becket 02 091 12 091 97 63 60
Single – fixed eye 02 110 12 110 79 50 47
Single – fixed eye + becket 02 111 12 111 88 56 53
Single – reverse shackle 02 120 12 120 94 60 58
Single – reverse shackle + becket 02 121 12 121 112 66 64
Single – swivel 02 130 12 130 97 64 62
Single – swivel + becket 02 131 12 131 105 70 69
Single – snap shackle 02 140 12 140 106 96 93
Single – snap shackle + becket 02 141 12 141 115 101 98
Single – upright 02 150 12 150 51 78 76
Single – upright with fairlead 02 151 12 151 75 87 85
Single – cheek block 02 160 12 160 80 73 69
Curved backing plate (for cheek block) 02 161 – 80 15 –
Single – stand up 02 170 12 170 112 138 137
Single – stand up + becket 02 171 12 171 117 142 140
Single – spinnaker lead 02 180 12 180 122 68 66
Double size 2 blocksDouble – fixed eye 02 210 12 210 79 80 77
Double – fixed eye + becket 02 211 12 211 87 86 84
Double – reverse shackle 02 220 12 220 93 91 89
Double – reverse shackle + becket 02 221 12 221 97 97 94
Double – swivel 02 230 12 230 98 96 95
Double – swivel + becket 02 231 12 231 109 102 100
Double – upright 02 250 12 250 63 110 108
Back to back swivel 02 280 12 280 141 98 96
Triple size 2 blocksTriple – reverse shackle 02 320 12 320 91 121 120
Triple – reverse shackle + becket 02 321 12 321 100 127 126
Triple – swivel 02 330 12 330 94 125 124
Triple – swivel + becket 02 331 12 331 105 132 130
Fiddle size 2 blocksFiddle – fixed eye 02 410 12 410 128 98 97
Fiddle – fixed eye + becket 02 411 12 411 137 100 99
Fiddle – reverse shackle 02 420 12 420 140 109 108
Fiddle – reverse shackle + becket 02 421 12 421 150 113 112
Fiddle – swivel 02 430 12 430 147 113 112
Fiddle – swivel + becket 02 431 12 431 155 117 116
Fiddle – snap shackle 02 440 12 440 155 142 141
Fiddle – snap shackle + becket 02 441 12 441 163 150 147
Cam cleat size 2 blocksSingle – swivel + becket + cam 02 531 12 531 119 127 125
Single – snap shackle + becket + cam 02 541 12 541 122 157 155
Single – stand up + becket + cam 02 571 12 571 132 201 197
Fiddle – swivel + becket + cam 02 631 12 631 155 165 164
Fiddle – snap shackle + becket + cam 02 641 12 641 165 196 195
Fiddle – swivel + becket + plastic cam 02 731 12 731 157 167 166
Stanchion lead size 2 blocksSingle – stanchion lead 02 190 12 190 110 78 77
Double – stanchion lead 02 290 12 290 108 108 104
control the power
size 2 blocks
02 09002 230
02 290
02 330
02 430
02 531
02 440
02 541
02 631
02 731
35mm standard blocks
02 250
Fixed EyeClevis PinA simple, low-pricedfixed eye block withremovable clevis pinfor attachment.Pin Ø 5mm. Widthbetween straps 13mm.
Fixed EyeWith a plainattachment eye.
ReverseShackleRemovable shacklethat can be setin-line or at 90°to the sheave.
SwivelFully swivelling headwith removable shackle.
Snap ShackleWith a cast stainlesssteel swivelling snapshackle. Ideal forquick-release down-hauls or vang tackles.
VarilocMulti HeadAllows swivel to belocked at 30° positionsin relation to sheave.Inverting the plasticlocking piece convertsto swivel mode.Supplied with screwpin strip shackle.
BecketAll the appropriate size3 blocks are availablewith or without becket.
Stand upFeatures a flexibleplastic spring foranti-tumble action.Base Ø 58mm.
Fastenings 5mm.
03 151
03 160
03 170
03180
Stanchion leadDesigned for use on25mm Ø tubes, with aswivelling action withup-down movementallowing for a fair leadon control lines.Note: A larger size 4 shouldbe used for final take off onfurling lines.
UprightWith or without fairlead.
Fairlead prevents linefalling away when notunder load.
Fastenings 5mm.
CheekWith a plastic backingplate standard - curvedbacking plate alsoavailable (03161),to allow snugattachment to spars etc.
Base size 92mm x52mm. Fastenings 5mm.
03161
03 511
Cam cleat blocksFitted with Kevlar ‘K’ cams(unless otherwise stated).Cam arms are fullyadjustable by movingthe locking clevis pin to
achieve the correct cleatingangle. Used in conjunction
with the relevant top block, this range ofblocks is particularly useful for mainsheet,vang tackles or downhauls on dinghies,dayboats or light cruising yachts.
control the power
size
3 b
lock
s A strong, lightweight range of blocks for use ondinghies, dayboats and light cruising yachts. Ideal formainsheet, vang, lead blocks or wherever a powerfuland compact purchase tackle is required.
A comprehensive range of cam cleat, fiddle, andfiddle & cam cleat versions are available.
Sheave size
Single 45mm x 13mm (13/4 x 1/2”)
Fiddle 30/54mm x 13mm (13/16 ” /13/4” x 1/2”)
Available with these heads and shackles...
8
03 150
03 190
03 090
45mm standard blocks
SWL
385kg (848lbs)
Max rolling load(ball bearing blocks)
270kg (595lbs)
Max rope diameter
10mm (3/8”)
Break load
770kg (1697 lbs)
Important note – break loads:Where break and safe working loads are stated, it is assumed that all sheaves are evenlyloaded as in a purchase tackle. Uneven loading, or loading of one sheave in a double ortriple block, will severely effect strength quoted. If unsure, please seek further advice.
Maximum rolling load on ball bearing blocks is the maximum free running load beforeball bearings will distort.
All available with plain or ball bearing sheaves:
Ball bearing blocksWith our unique super-low friction ball racesystems, featuring acetal sheaves and delrin ballbearings, running on a large diameter centreboss. This allows us to fit more load-bearingballs, which ensure extremely low frictionperformance, even under high loads.
Plain bearing blocksBarton plain bearing blocks have a precisionmoulded acetal sheave running on a largediameter brass bearing, ensuring freerunning under the highest of loads.
9
Plain Ball-bearing Length Weight (g)sheave sheave mm plain ball
Single size 3 blocksSingle – fixed eye clevis pin 03 090 13 090 97 85 88
Single – fixed eye clevis pin + becket 03 091 13 091 112 94 96
Single – fixed eye 03 110 13 110 90 77 79
Single – fixed eye + becket 03 111 13 111 107 84 88
Single – reverse shackle 03 120 13 120 105 85 88
Single – reverse shackle + becket 03 121 13 121 117 94 96
Single – swivel 03 130 13 130 107 89 90
Single – swivel + becket 03 131 13 131 122 97 99
Single – snap shackle 03 140 13 140 118 121 122
Single – snap shackle + becket 03 141 13 141 132 130 131
Single – upright 03 150 13 150 75 122 126
Single – upright with fairlead 03 151 13 151 85 132 133
Single – cheek block 03 160 13 160 92 109 110
Curved backing plate (for cheek block) 03 161 – 92 19 –
Single – stand up 03 170 13 170 118 158 162
Single – stand up + becket 03 171 13 171 129 169 172
Single – variloc 03 180 13 180 104 90 92
Single – variloc + becket 03 181 13 181 117 98 100
Double size 3 blocksDouble – fixed eye 03 210 13 210 90 124 131
Double – fixed eye + becket 03 211 13 211 100 132 136
Double – reverse shackle 03 220 13 220 104 134 139
Double – reverse shackle + becket 03 221 13 221 117 142 146
Double – swivel 03 230 13 230 107 138 144
Double – swivel + becket 03 231 13 231 127 147 152
Double – upright 03 250 13 250 75 171 176
Triple size 3 blocksTriple – reverse shackle 03 320 13 320 104 183 193
Triple – reverse shackle + becket 03 321 13 321 117 191 199
Triple – swivel 03 330 13 330 117 204 213
Triple – swivel + becket 03 331 13 331 130 211 220
Fiddle size 3 blocksFiddle – fixed eye 03 410 13 410 147 151 156
Fiddle – fixed eye + becket 03 411 13 411 160 157 167
Fiddle – reverse shackle 03 420 13 420 162 161 165
Fiddle – reverse shackle + becket 03 421 13 421 175 168 172
Fiddle – swivel 03 430 13 430 165 163 168
Fiddle – swivel + becket 03 431 13 431 176 170 177
Fiddle – snap shackle 03 440 13 440 174 195 199
Fiddle – snap shackle + becket 03 441 13 441 188 202 206
Fiddle – variloc 03 480 13 480 160 165 169
Fiddle – variloc + becket 03 481 13 481 175 163 188
Cam cleat size 3 blocksSingle – swivel + becket + cam 03 511 13 511 121 188 196
Triple – swivel + becket + cam 03 531 13 531 137 306 315
Single – snap shackle + becket + cam 03 541 13 541 129 345 347
Single – stand up + becket + cam 03 571 13 571 136 261 263
Fiddle – swivel + becket + cam 03 631 13 631 178 250 255
Fiddle – snap shackle + becket + cam 03 641 13 641 188 281 280
Fiddle – variloc + becket + cam 03 681 13 681 170 253 257
Fiddle – swivel + becket + plastic cam 03 731 13 731 178 253 257
Stanchion lead size 3 blocksSingle – stanchion lead 03 190 13 190 120 104 106
03 140
03 250
03 440
www.bartonmarine.com
size 3 blocks
03 330
03 130
03 230
03 430
03 631
03 641
03 731
03 531 03 571
45mm standard blocks
Fixed EyeClevis PinA simple, low-pricedfixed eye block withremovable clevis pinfor attachment.Pin Ø 6mm. Widthbetween straps 13mm.
Fixed EyeWith a plainattachment eye.
ReverseShackleRemovable shacklethat can be setin-line or at 90°to the sheave.
SwivelFully swivelling headwith removable shackle.
Snap ShackleWith a cast stainlesssteel swivelling snapshackle. Ideal forquick-release down-hauls or vang tackles.
VarilocMulti HeadAllows swivel to belocked at 30° positionsin relation to sheave.Inverting the plasticlocking piece convertsto swivel mode.Supplied with screwpin strip shackle.
BecketAll the appropriate size4 blocks are availablewith or without becket.
Cam cleat blocksFitted with Kevlar
‘K’ cams (unlessotherwise stated).Cam arms are fullyadjustable bymoving the locking
clevis pin to achievethe correct cleating angle.
Used in conjunction with therelevant top block, this range ofblocks is particularly useful formainsheet, vang tackles ordownhauls on dinghies, dayboatsor light cruising yachts.
Stand upFeatures a flexibleplastic spring foranti-tumble action.Base Ø 58mm.
Fastenings 5mm.
04 150
04 170
04 090
UprightWith or withoutfairlead.
Fairlead preventsline falling awaywhen notunder load.
Fastenings 5mm.
04 931
www.bartonmarine.com
size
4 b
lock
s A strong, lightweight range of blocks for use on dayboatsand cruising yachts. Ideal for mainsheets, vang tackles,lead blocks or wherever a powerful and compact purchasetackle is required.
A comprehensive range of cam cleat, fiddle, and fiddle &cam cleat versions are available.
Sheave size
Single 58mm x 17mm (21/4 x 5/8”)
Fiddle 32/58mm x 17mm (11/14 ” /21/4” x 5/8”)
Available with these heads and shackles...
10
04190
SWL
630kg (1385lbs)
Max rolling load(ball bearing blocks)
440kg (970lbs)
Max rope diameter
12mm (7/16”)
Break load
1260kg (2770lbs)
04 140
58mm standard blocks
04 130
CheekWith plastic backing plate to eliminate
damage to spars or decks.
Base size 107mm x 67mm.Fastenings 5mm.
04 160
04 180
04 151
Stanchion leadDesigned for use on
25mm Ø tubes, with aswivelling action with
up-down movementallowing for afair lead oncontrol lines.
Important note – break loads:Where break and safe working loads are stated, it is assumed that all sheaves are evenlyloaded as in a purchase tackle. Uneven loading, or loading of one sheave in a double ortriple block, will severely effect strength quoted. If unsure, please seek further advice.
Maximum rolling load on ball bearing blocks is the maximum free running load beforeball bearings will distort.
All available with plain or ball bearing sheaves:
Ball bearing blocksWith our unique super-low friction ball racesystems, featuring acetal sheaves and delrin ballbearings, running on a large diameter centreboss. This allows us to fit more load-bearingballs, which ensure extremely low frictionperformance, even under high loads.
Plain bearing blocksBarton plain bearing blocks have a precisionmoulded acetal sheave running on a largediameter brass bearing, ensuring freerunning under the highest of loads.
11
Plain Ball-bearing Length Weight (g)sheave sheave mm plain ball
Single size 4 blocksSingle – fixed eye clevis pin 04 090 14 090 120 166 161
Single – fixed eye clevis pin + becket 04 091 14 091 140 177 175
Single – fixed eye 04 110 14 110 114 156 150
Single – fixed eye + becket 04 111 14 111 135 170 166
Single – reverse shackle 04 120 14 120 130 172 167
Single – reverse shackle + becket 04 121 14 121 150 187 181
Single – swivel 04 130 14 130 138 187 181
Single – swivel + becket 04 131 14 131 157 199 198
Single – snap shackle 04 140 14 140 148 257 250
Single – snap shackle + becket 04 141 14 141 170 269 266
Single – upright 04 150 14 150 92 218 214
Single – upright with fairlead 04 151 14 151 105 234 231
Single – cheek block 04 160 14 160 107 178 174
Single – stand up 04 170 14 170 135 243 237
Single – stand up block + becket 04 171 14 171 152 262 253
Single – variloc 04 180 14 180 131 189 181
Single – variloc + becket 04 181 14 181 150 203 200
Double size 4 blocksDouble – fixed eye 04 210 14 210 115 270 261
Double – fixed eye + becket 04 211 14 211 135 286 277
Double – reverse shackle 04 220 14 220 130 275 263
Double – reverse shackle + becket 04 221 14 221 147 288 285
Double – swivel 04 230 14 230 138 291 283
Double – swivel + becket 04 231 14 231 162 305 296
Double – upright 04 250 14 250 92 321 314
Triple size 4 blocksTriple – reverse shackle 04 320 14 320 132 377 365
Triple – reverse shackle + becket 04 321 14 321 145 391 380
Triple – swivel 04 330 14 330 139 391 380
Triple – swivel + becket 04 331 14 331 155 406 396
Fiddle size 4 blocksFiddle – fixed eye 04 410 14 410 160 225 211
Fiddle – fixed eye + becket 04 411 14 411 178 237 225
Fiddle – reverse shackle 04 420 14 420 175 239 228
Fiddle – reverse shackle + becket 04 421 14 421 195 253 239
Fiddle – swivel 04 430 14 430 185 254 244
Fiddle – swivel + becket 04 431 14 431 202 267 252
Fiddle – snap shackle 04 440 14 440 195 326 316
Fiddle – snap shackle + becket 04 441 14 441 215 339 322
Fiddle – variloc 04 480 14 480 177 259 243
Fiddle – variloc + becket 04 481 14 481 197 269 260
Fiddle – triple 04 930 14 930 192 359 344
Cam cleat size 4 blocksSingle – swivel + becket + cam 04 531 14 531 157 307 299
Single – snap shackle + becket + cam 04 541 14 541 167 389 381
Single – stand up + becket + cam 04 571 14 571 152 365 358
Fiddle – double swivel + cam 04 630 14 630 150 532 503
Fiddle – swivel + becket + cam 04 631 14 631 198 372 358
Fiddle – snap shackle + becket + cam 04 641 14 641 214 447 432
Fiddle – variloc + becket + cam 04 681 14 681 195 375 361
Fiddle – swivel + becket + plastic cam 04 731 14 731 206 378 364
Triple – swivel + becket + cam 04 931 14 931 150 597 586
Stanchion lead size 4 blocksSingle – stanchion lead 04 190 14 190 140 197 190
control the power
size 4 blocks
04 230
04 330
04 430
04 531
04 440
04 631
04 641
58mm standard blocks
04 250
04 571
04 630
04 930
Fixed EyeWith a plainattachment eye.
Reverse ShackleRemovable shackle thatcan be set in-line or at90° to the sheave.
SwivelFully swivelling headwith removable shackle.
Snap ShackleWith a cast stainless steelswivelling snap shackle.Ideal for quick-releasedownhauls or vang tackles.
Variloc Multi HeadAllows swivel to be locked at 30°positions in relation to sheave.Inverting the plastic locking piececonverts to swivel mode. Suppliedwith screw pin strip shackle.
BecketAll the appropriatesize 5 blocks areavailable with orwithout becket.
Stand upFeatures a flexibleplastic spring foranti-tumble action.Base Ø 67mm.
Fastenings 6mm.
05 170
05 631
control the power
size
5 b
lock
s This range of high load cruiser blocks are of ruggedconstruction, featuring high quality injection moulded sideplates with all load-carrying components from 316 gradestainless steel. Side plates are through-bolted and rivetedfor added strength and security.
This good looking and versatile range is designed for useon larger cruising and racing yachts. All are designed forease of use with our ball-bearing mainsheet travellersystems – see pages 22-27.
A comprehensive range of cam cleat, fiddle, and fiddle& cam cleat versions are available.
Sheave size
Single 54mm x 17mm (21/8 x 5/8”)
Fiddle 38/64mm x 17mm (11/2 ” /21/2” x 5/8”)
Available with these heads and shackles...
12
54mm cruiser blocks
SWL750kg (1650lbs)
Max rolling load(ball bearing blocks)525kg (1157lbs)
Max rope diameter
12mm (7/16”)
Break load1500kg (3300lbs)
Cam cleat blocksFitted with Kevlar ‘K’ cams.Stainless steel cam arms arefully adjustable by moving thelocking clevis pin to achieve thecorrect cleating angle. Used inconjunction with the relevanttop block, this range of blocksis particularly useful formainsheet, vang tackles orpowerful downhauls.
05 641
05 430
05 440
All available with plain or ball bearing sheaves:
Ball bearing blocksWith our unique super-low friction ball racesystems, featuring acetal sheaves and delrin ballbearings, running on a large diameter centreboss. This allows us to fit more load-bearingballs, which ensure extremely low frictionperformance, even under high loads.
Plain bearing blocksBarton plain bearing blocks have a precisionmoulded acetal sheave running on a largediameter brass bearing, ensuring freerunning under the highest of loads.
13
Plain Ball-bearing Length Weight (g)sheave sheave mm plain ball
Single size 5 blocksSingle – fixed eye 05 110 15 110 107 154 140
Single – fixed eye + becket 05 111 15 111 130 177 163
Single – reverse shackle 05 120 15 120 130 178 164
Single – reverse shackle + becket 05 121 15 121 150 204 189
Single – swivel 05 130 15 130 130 197 183
Single – swivel + becket 05 131 15 131 153 220 206
Single – snap shackle 05 140 15 140 142 263 247
Single – snap shackle + becket 05 141 15 141 165 286 272
Single – stand up 05 170 15 170 140 347 329
Single – stand up + becket 05 171 15 171 163 370 352
Single – variloc 05 180 15 180 125 195 181
Single – variloc + becket 05 181 15 181 148 218 205
Double size 5 blocksDouble – reverse shackle 05 220 15 220 125 274 247
Double – reverse shackle + becket 05 221 15 221 147 300 272
Triple size 5 blocksTriple – reverse shackle 05 320 15 320 130 382 337
Triple – reverse shackle + becket 05 321 15 321 148 402 365
Triple – swivel 05 330 15 330 150 490 475
Triple – swivel + becket 05 331 15 331 173 513 498
Fiddle size 5 blocksFiddle – reverse shackle 05 420 15 420 185 278 255
Fiddle – reverse shackle + becket 05 421 15 421 205 300 285
Fiddle – swivel 05 430 15 430 185 300 278
Fiddle – swivel + becket 05 431 15 431 209 318 296
Fiddle – snap shackle 05 440 15 440 200 362 340
Fiddle – snap shackle + becket 05 441 15 441 220 378 360
Fiddle – variloc 05 480 15 480 185 295 275
Fiddle – variloc + becket 05 481 15 481 209 296 276
Cam cleat size 5 blocksFiddle – swivel + becket + cam 05 631 15 631 209 469 449
Fiddle – snap shackle + becket + cam 05 641 15 641 215 568 553
Fiddle – variloc + becket + cam 05 681 15 681 205 508 490
Triple – swivel + cam 05 930 15 930 150 660 645
Triple – swivel + becket + cam 05 931 15 931 173 683 668
www.bartonmarine.com
size 5 blocks
05 130
54mm cruiser blocks
05 140
05 180
05 220
05 320
05 930
05 330
Important note – break loads:Where break and safe working loads are stated, it is assumed that all sheaves are evenlyloaded as in a purchase tackle. Uneven loading, or loading of one sheave in a double ortriple block, will severely effect strength quoted. If unsure, please seek further advice.
Maximum rolling load on ball bearing blocks is the maximum free running load beforeball bearings will distort.
Fixed EyeWith a plainattachment eye.
Reverse ShackleRemovable shackle thatcan be set in-line or at90° to the sheave.
SwivelFully swivelling headwith removable shackle.
Snap ShackleWith a cast stainless steelswivelling snap shackle.Ideal for quick-releasedownhauls or vang tackles.
Variloc Multi HeadAllows swivel to be locked at 30°positions in relation to sheave.Inverting the plastic locking piececonverts to swivel mode. Suppliedwith screw pin strip shackle.
BecketAll the appropriatesize 6 blocks areavailable with orwithout becket.
www.bartonmarine.com
size
6 b
lock
s This range of high load cruiser blocks are of ruggedconstruction, featuring high quality injection moulded sideplates with all load-carrying components from 316 gradestainless steel. Side plates are through-bolted and rivetedfor added strength and security.
This good looking and versatile range is designed for useon larger cruising and racing yachts. All are designed forease of use with our ball-bearing mainsheet travellersystems – see pages 22-27.
A comprehensive range of cam cleat, fiddle, and fiddle &cam cleat versions are available.
Sheave size
Single 64mm x 17mm (21/2 x 5/8”)
Fiddle 44/70mm x 17mm (13/4 ” /23/4” x 5/8”)
Available with these heads and shackles...
14
64mm cruiser blocks
SWL1000kg (2200lbs)
Max rolling load(ball bearing blocks)700kg (1543lbs)
Max rope diameter
12mm (7/16”)
Break load2000kg (4400lbs)
06 930
Cam cleatblocksFitted with Kevlar ‘K’ cams. Stainlesssteel cam arms are fully adjustableby moving the locking clevis pin toachieve the correct cleating angle.Used in conjunction with the relevanttop block, this range of blocks isparticularly useful for mainsheet,vang tackles or powerful downhauls.
Stand upFeatures a flexibleplastic spring foranti-tumble action.Base Ø 67mm.
Fastenings 6mm.
06 170
Important note – break loads:Where break and safe working loads are stated, it is assumed that allsheaves are evenly loaded as in a purchase tackle. Uneven loading, orloading of one sheave in a double or triple block, will severely effectstrength quoted. If unsure, please seek further advice.
Maximum rolling load on ball bearing blocks is the maximum free runningload before ball bearings will distort.
All available with plain or ball bearing sheaves:
Ball bearing blocksWith our unique super-low friction ball racesystems, featuring acetal sheaves and delrin ballbearings, running on a large diameter centreboss. This allows us to fit more load-bearingballs, which ensure extremely low frictionperformance, even under high loads.
Plain bearing blocksBarton plain bearing blocks have a precisionmoulded acetal sheave running on a largediameter brass bearing, ensuring freerunning under the highest of loads.
15
Plain Ball-bearing Length Weight (g)sheave sheave mm plain ball
Single size 6 blocksSingle – fixed eye 06 110 16 110 118 180 172
Single – fixed eye + becket 06 111 16 111 147 210 201
Single – reverse shackle 06 120 16 120 140 206 197
Single – reverse shackle + becket 06 121 16 121 165 232 225
Single – swivel 06 130 16 130 142 227 217
Single – swivel + becket 06 131 16 131 167 255 245
Single – snap shackle 06 140 16 140 170 292 283
Single – snap shackle + becket 06 141 16 141 180 322 307
Single – stand up 06 170 16 170 150 369 361
Single – stand up + becket 06 171 16 171 179 399 391
Single – variloc 06 180 16 180 138 228 217
Single – variloc + becket 06 181 16 181 165 254 244
Double size 6 blocksDouble – reverse shackle 06 220 16 220 135 325 307
Double – reverse shackle + becket 06 221 16 221 164 352 334
Triple size 6 blocksTriple – reverse shackle 06 320 16 320 135 449 425
Triple – reverse shackle + becket 06 321 16 321 167 476 455
Triple – swivel 06 330 16 330 170 686 662
Triple – swivel + becket 06 331 16 331 193 716 692
Fiddle size 6 blocksFiddle – reverse shackle 06 420 16 420 210 339 321
Fiddle – reverse shackle + becket 06 421 16 421 233 366 350
Fiddle – swivel 06 430 16 430 210 357 346
Fiddle – swivel + becket 06 431 16 431 235 388 358
Fiddle – snap shackle 06 440 16 440 220 417 407
Fiddle – snap shackle + becket 06 441 16 441 250 450 437
Fiddle – variloc 06 480 16 480 205 356 335
Fiddle – variloc + becket 06 481 16 481 232 383 362
Cam cleat size 6 blocksFiddle – swivel + becket + cam 06 631 16 631 232 575 554
Fiddle – snap shackle + becket + cam 06 641 16 641 245 639 618
Fiddle – variloc + becket + cam 06 681 16 681 235 575 557
Triple – swivel + cam 06 930 16 930 170 856 832
Triple – swivel + becket + cam 06 931 16 931 193 886 862
06 631
control the power
size6 b
locks06 130
64mm cruiser blocks
06 140
06 180
06 641
06 220
06 43006 440
06 320
06 330
Fixed EyeWith a plainattachment eye.
Reverse ShackleRemovable shackle thatcan be set in-line or at90° to the sheave.
SwivelFully swivelling headwith removable shackle.
Snap ShackleWith a cast stainless steelswivelling snap shackle.Ideal for quick-releasedownhauls or vang tackles.
Variloc Multi HeadAllows swivel to be locked at 30°positions in relation to sheave.Inverting the plastic locking piececonverts to swivel mode. Suppliedwith screw pin strip shackle.
BecketAll the appropriatesize 7 blocks areavailable with orwithout becket.
07 631
control the power
size
7 b
lock
s This range of high load cruiser blocks are of ruggedconstruction, featuring high quality injection moulded sideplates with all load-carrying components from 316 gradestainless steel. Side plates are through-bolted and rivetedfor added strength and security.
This good looking and versatile range is designed for useon larger cruising and racing yachts. All are designed forease of use with our ball-bearing mainsheet travellersystems – see pages 22-27.
A comprehensive range of cam cleat, fiddle, and fiddle &cam cleat versions are available.
Sheave size
Single 70mm x 20mm (23/4 x 3/4”)
Fiddle 44/70mm x 17mm (13/4 ” /23/4” x 5/8”)
Available with these heads and shackles...
16
70mm cruiser blocks
SWL1500kg (3300lbs)
Max rolling load(ball bearing blocks)
875kg (1929lbs)
Max rope diameter
14mm (9/16”)
Break load2500kg (5500lbs)
07 641
07 430
07 440
Cam cleat blocksFitted with Kevlar ‘K’ cams. Stainless steel cam arms are fullyadjustable by moving the locking clevis pin to achieve thecorrect cleating angle. Used in conjunction with the relevanttop block, this range of blocks is particularly useful formainsheet, vang tackles or powerful downhauls.
Important note – break loads:Where break and safe working loads are stated, it is assumed that allsheaves are evenly loaded as in a purchase tackle. Uneven loading, orloading of one sheave in a double or triple block, will severely effectstrength quoted. If unsure, please seek further advice.
Maximum rolling load on ball bearing blocks is the maximum free runningload before ball bearings will distort.
All available with plain or ball bearing sheaves:
Ball bearing blocksWith our unique super-low friction ball racesystems, featuring acetal sheaves and delrin ballbearings, running on a large diameter centreboss. This allows us to fit more load-bearingballs, which ensure extremely low frictionperformance, even under high loads.
Plain bearing blocksBarton plain bearing blocks have a precisionmoulded acetal sheave running on a largediameter brass bearing, ensuring freerunning under the highest of loads.
17
Plain Ball-bearing Length Weight (g)sheave sheave mm plain ball
Single size 7 blocksSingle – fixed eye 07 110 17 110 137 246 237
Single – fixed eye + becket 07 111 17 111 166 282 271
Single – reverse shackle 07 120 17 120 168 308 299
Single – reverse shackle + becket 07 121 17 121 195 343 337
Single – swivel 07 130 17 130 163 354 345
Single – swivel + becket 07 131 17 131 197 389 382
Single – snap shackle 07 140 17 140 168 359 350
Single – snap shackle + becket 07 141 17 141 200 394 385
Single – stand up 07 170 17 170 162 444 439
Single – stand up + becket 07 171 17 171 191 480 471
Single – variloc 07 180 17 180 163 328 317
Single – variloc + becket 07 181 17 181 192 364 348
Double size 7 blocksDouble – reverse shackle 07 220 17 220 160 461 448
Double – reverse shackle + becket 07 221 17 221 195 491 484
Triple size 7 blocksTriple – reverse shackle 07 320 17 320 165 616 604
Triple – reverse shackle + becket 07 321 17 321 199 646 637
Triple – swivel 07 330 17 330 163 734 725
Triple – swivel + becket 07 331 17 331 192 770 761
Fiddle size 7 blocksFiddle – reverse shackle 07 420 17 420 220 398 390
Fiddle – reverse shackle + becket 07 421 17 421 252 428 410
Fiddle – swivel 07 430 17 430 220 449 406
Fiddle – swivel + becket 07 431 17 431 248 470 361
Fiddle – snap shackle 07 440 17 440 222 448 431
Fiddle – snap shackle + becket 07 441 17 441 253 488 461
Fiddle – variloc 07 480 17 480 220 417 405
Fiddle – variloc + becket 07 481 17 481 249 439 430
Cam cleat size 7 blocksFiddle – swivel + becket + cam 07 631 17 631 248 660 651
Fiddle – snap shackle + becket + cam 07 641 17 641 250 668 644
Fiddle – variloc + becket + cam 07 681 17 681 245 637 628
Triple – swivel + cam 07 930 17 930 163 770 761
Triple – swivel + becket + cam 07 931 17 931 192 806 797
Stand upFeatures a flexible plasticspring for anti-tumbleaction. Base Ø 67mm.
Fastenings 6mm.
07 170
www.bartonmarine.com
size7 b
locks07 180
70mm cruiser blocks
07 140
07 130
07 220
07 320
07 930
07 330
Specifications Size 1 Size 2 Size 3
Sheave Ø 30mm 35mm 45mm
Sheave width 11mm 11mm 13mm
Max rope Ø 8mm 8mm 10mm
Break load 560kg 800kg 800kg
SWL 280kg 400kg 400kg
Max rolling load 200kg 280kg 280kg(ball bearing blocks)
95 102
www.bartonmarine.com
sta
inle
ss s
teel
blo
cks For lines up to 10mm diameter.
Available with plain or ball bearing sheaves.A robust range of stainless steel blocks with a multitude ofuses on all types of sailing boats.
Highly polished side plates with flared cheeks prevent thepossibility of chafing the line whilst giving added strength.
A range of jamming blocks is also available – giving the abilityto make up strong, powerful, compact and lightweight tackles.
These are ideal for use on dinghies and dayboats forkicking straps or wherever a compact and powerfulrope tackle is required.
18
30/35/45mm stainless blocks
Plain Ball-bearing Length Weight (g)sheave sheave mm plain ball
Single size 1 S/S blocks
Single 95 100 95 400 50 34 32
Single + becket 95 101 95 401 67 45 43
Single – Fixed Eye 95 102 95 402 68 39 37
Single – Fixed Eye + becket 95 103 95 403 85 48 46
Single – Swivel 95 104 95 404 86 53 51
Single – Swivel + becket 95 105 95 405 100 63 61
Double size 1 S/S blocksDouble – Fixed Eye 95 120 95 420 68 60 54
Double – Fixed Eye + becket 95 121 95 421 85 70 66
Double – Swivel 95 122 95 422 83 76 72
Double – Swivel + becket 95 123 95 423 100 86 82
Triple size 1 S/S blocksTriple – Fixed Eye 95 130 95 430 68 82 76
Triple – Fixed Eye + becket 95 137 95 437 85 93 87
Triple – Swivel 95 138 95 438 83 99 93
Triple – Swivel + becket 95 139 95 439 100 109 103
Jamming size 1 S/S blocksSingle Jamming + becket 95 131 95 431 100 95 93
Double Jamming + becket 95 132 95 432 100 117 113
Triple Jamming + becket 95 133 95 433 100 140 134
Single size 2 S/S blocksSingle 95 200 95 500 61 45 45
Single + becket 95 201 95 501 84 60 60
Single – Fixed Eye 95 202 95 502 76 48 48
Single – Fixed Eye + becket 95 203 95 503 99 63 63
Single – Swivel 95 204 95 504 96 63 63
Single – Swivel + becket 95 205 95 505 119 79 79
Double size 2 S/S blocksDouble – Fixed Eye 95 220 95 520 76 77 77
Double – Fixed Eye + becket 95 221 95 521 98 92 92
Double – Swivel 95 222 95 522 95 92 92
Double – Swivel + becket 95 223 95 523 116 107 107
Triple size 2 S/S blocksTriple – Fixed Eye 95 230 95 530 75 105 105
Triple – Fixed Eye + becket 95 231 95 531 97 120 120
Triple – Swivel 95 232 95 532 97 121 121
Triple – Swivel + becket 95 233 95 533 117 136 136
Single size 3 S/S blocksSingle 95 300 95 600 80 61 64
Single + becket 95 301 95 601 112 80 83
Single – Fixed Eye 95 302 95 602 93 71 74
Single – Fixed Eye + becket 95 303 95 603 124 94 97
Single – Swivel 95 304 95 604 107 87 90
Single – Swivel + becket 95 305 95 605 139 107 110
Double size 3 S/S blocksDouble – Fixed Eye 95 320 95 620 93 112 118
Double – Fixed Eye + becket 95 321 95 621 124 136 142
Double – Swivel 95 322 95 622 107 129 135
Double – Swivel + becket 95 323 95 623 139 149 155
Triple size 3 S/S blocksTriple – Fixed Eye 95 330 95 630 93 153 162
Triple – Fixed Eye + becket 95 331 95 631 124 185 194
Triple – Swivel 95 332 95 632 167 135 144
Triple – Swivel + becket 95 333 95 633 139 167 176
95 100
95 10495 105
95 121
95 122
95 130
95 123
95 137
95 138 95 132
95 120
19control the power
Important note – break loads:Where break and safe working loads are stated, it is assumed that all sheaves are evenly loaded with a straight lead.
Loads are not given for cheek blocks or upright blocks as this is dependent on fastenings used.To ensure maximum strength and load capabilities, fastenings must pass through hollow centre rivets of cheek blocks.
wire rop
e blocks
Wire Rope blocks
Part Sheave Sheave Rope Wire Break SWL WeightNo. Ø mm width mm Ø mm Ømm Load kg kg g
Aluminium blocksSingle – Fixed Eye 91 600 51 15 12 4 1750 875 155
Single – Fixed Eye 91 700 63 18 16 5 3000 1500 248
Cheek 91 650 51 15 12 4 – – 141
Cheek 91 750 63 18 16 5 – – 227
Brass sheave blocksSingle – Fixed Eye 91 200 35 8 4 4 400 200 67
Single – Fixed Eye 91 300 45 8 5 5 750 375 106
Upright blocksSingle – Fixed Eye 91 400 38 12 8 4 – – 92
Single – Fixed Eye 91 500 51 15 12 5 – – 160
High load wire rope blocksFixed Eye 91 301 45 8 5 5 1300 650 163
Swivel Eye 91 302 45 8 5 5 1300 650 212
Backstay tensionerBackstay tensioner system 02 740 45 8 5 5 1300 650 163
Backstay tensioner block 91 020 35 8 – 5 – – 277
Backstay tensioner block 91 040 50 15 – 10 – – 585
Aluminium high load blocksA range of high strength blocksdesigned for use with wire ropes orin exceptionally rugged conditions.
Cheeks are manufactured frommarine-grade aluminium, ‘Spectro’grey anodised for high UV-resistanceand durability.
Sheaves are precision-turned fromsolid aluminium bar, silver anodisedand running on nylon bearings toreduce friction under load.
Reinforcing plates, rivets andshackle straps are all from 316stainless steel.
Cheek block dimensions
91650 base 103 x 53mmfastenings 5mm
91670 base 120 x 65mmfastenings 6mm
Upright blocksWith heavy-duty 316 stainless steel side plates.Sheaves are precision turned from solidaluminium bar, silver anodised and running onnylon bearings to reduce friction under load.
91 600
91 700
91 650
91 750
91 301
High load wire rope blocksAvailable in fixed eye or swivel head.Cheeks are manufactured from 316stainless steel and sheaves are precisionturned from solid brass bar, runningon a stainless steel centre bush.
91 302
91 200
91 300
Brass SheaveBlocksA simple lead blockwith turned brasssheave and stainlesssteel fixed eye strap.
91 400
91 500
02 740Upright block dimensions
91 400 Base 38 x 45mm Fastenings 5mm91 500 Base 51 x 55mm Fastenings 6mm
BackstaytensionersystemA block andtackle systemdesigned foruse on split ortwin backstays.Features stainlesssteel double blockwith brass sheaves,together withtensioning blocksfrom our size2 range.
Backstay tensioner blocksFeaturing laser-cut stainless steel sideplates with precision turned brass shaves.For use on twin or split backstays – forbackstay wire of up to 10mm Ø.
91 020
91 040
control the power
sna
tch
blo
cks
20
Snatch blocks
Part Sheave Sheave Rope Break SWL Length WeightNo. Ø mm width mm Ø mm Load kg kg mm g
Medium snatch blocksSnatch block + bronze snap 90 400 48 20 16 900 450 429 422
Snatch block + S/S snap 90 401 48 20 16 1100 550 362 378
Snatch block + S/S ‘D’ shackle 90 402 48 20 16 1300 650 370 316
Small snatch blocksSmall snatch block + bronze snap 90 300 35 17 12 500 250 120 203
Small snatch block + S/S snap 90 301 35 17 12 800 400 110 170
Lightweight snatch blocksSnatch block + S/S ‘D’ shackle 90 100 45 13 10 190 95 120 148
Snatch block + S/S snap 90 101 45 13 10 190 95 145 180
Snatch block + S/S ‘D’ shackle 90 200 57 16 12 460 230 155 227
Snatch block + S/S snap 90 201 57 16 12 460 230 178 298
Four sizes – acceptinglines up to 16mm Ø (5/8”)Our ever popular range of snatchblocks - of rugged constructionwith an easy open/close action.
The range features a choice ofstainless snap shackles, chromedbronze snap shackle or stainlesssteel ‘D’ shackle.
Small snatch blocksUnique to Barton, these areprobably the smallest block ofthis type available.
Extremely compact and strong,with a multitude of uses oncruising or racing yachts wherea large unit is not required.
Available with a stainless steel orchromed bronze snap shackle.
Lightweightsnatch blocksDesigned for applications ondinghies, dayboats or light cruisingyachts where a high load capacityis not required. A pivoting sideopening action allows for easyentry of sheets and lines.
Available with a stainless steelsnap shackle or ‘D’ shackle.
Important note– snatch blocks:When using snatch blocks on a toerail, a bungee line should be attachedto the becket to prevent the block‘tumbling’ and causing damageby snagging.
90 201
90 200
90 10090 101
90 402 90 401 90 400
90 30090 301
21www.bartonmarine.com
high loa
d b
locksHigh Load and Foot blocks
Part Sheave Sheave Rope Break SWL Length WeightNo. Ø mm width mm Ø mm Load kg kg mm g
High load blocksHigh load block – 50mm 82 100 50 15 12 1000 500 116 146
High load block – 65mm 82 200 65 18 16 1600 800 142 267
High load block – 85mm 82 300 85 21 18 3000 1500 185 551
Foot blocksFoot block – 50mm 82 995 50 15 12 1000 500 79 114
Foot block – 65mm 82 996 65 18 16 1600 800 100 211
Foot block – 85mm 82 997 85 21 18 3000 1500 132 427
Foot blocks with camsFoot block – 50mm 82 998 50 15 12 1000 500 84 130
Foot block – 65mm 82 999 65 18 16 1600 800 105 230
High load blocksManufactured from marine gradealuminium and ‘Spectro’ grey anodisedfor high UV stability and durability.• Sheaves are precision turned from
solid ‘Ertalyte’ bar with a profilethat is kind to modern ropes.
• Running on a large diametercentre bearing for easy runningunder high loads.
• Fitted with a stainless steelbow shackle to allow forsnag-free operation.
• Bolt-together constructionnot only adds to good looks,but allows for easydismantling shouldservicing become necessary.
• Available in three sizes, theseblocks are compatible with thetoggle connections on our ballbearing mainsheet travellers(pages 22-27).
82 100
Foot blocksFeaturing the same side plate and sheave constructionas the high load blocks detailed above.
• Hollow stainless steel rivets allowfor through-bolt fastening, givingadded strength.
• Through-bolt mounting also means thatthese blocks can easily be stacked toachieve double block capabilities. Note;stacking blocks will reduce working loads.
• Fastenings of the minimum diametersuggested should be used to gain fullload capability.
• Ensure that suitable mounting pads areused under deck.
Foot blocks with camAvailable in two sizes; specifications as perour high load foot block range. Suitablefor a multitude of uses, including lockingcontrol lines on headsail furling gear.
Max holding power of cams: 50mm – 250kg; 65mm – 300kg
82 200
82 99882 999
82 997 82 99682 995
82 300
Important note – foot blocks:Fastenings of the minimum diametersuggested should be used to gain fullload capacity. Ensure that suitablemounting pads are provided under deck.
Stacking blocks to achieve doubles willseverely reduce working loads quoted.
Barton travellers can be easily built up frommodular components to give a wide variety ofcontrol line purchase, either cleated on track ends,traveller or remotely.
The following pages explain how to make up yourown individual system by putting together modularcomponents, including a choice of three types of track.
When selecting which system will suit your requirements,ask the following questions:
1. Size of boat?
2. Control line purchase (2:1, 3:1 or 4:1)?
3. Shackle or toggle take-off?
4. Single or double take-off?
5. Cleating on car, end fittings or remote?
6. End fitting cleats straight or angled?
Guide to choice of size:
Size 1 for yachts up to 8.5m (28.5ft)
Size 2 for yachts up to 11.0m (36ft)
Size 3 for yachts up to 14.0m (46ft)
www.bartonmarine.com
ma
insh
eet &
gen
oa c
ar s
yste
ms
22
Recirculating ball bearing mainsheet systems
A unique way to select the best traveller and genoa car system for yourboat and personal requirements – a truly low friction system, realisticallypriced and designed for use on both cruising and racing yachts.
Travellers, end fittings and track are all extruded from top qualitymarine grade aluminium and finished in our unique ‘Spectro’ greyanodised finish.
• Recirculating precision ground delrin ball system
• Three sizes for yachts up to 14m LOA (46ft)
• Three track options
• Construct your own system from modular components(pages 25-28) or choose one of our new pre-packagedcomplete systems (page 24)
• Single or double take off travellers
• Shackle or toggle take off travellers
• Multiple control line purchase (2:1, 3:1, 4:1)
• Cleating on end fitting or car
• Kevlar ‘K’ cam with 70° or 90° angled cleating options
• Torlon ball option
• Towable genoa cars.
TravellersAesthetic design, clean lines, high-techmaterials and finishes all go to make thisrange of traveller cars a functional andpractical enhancement to any sailboat.
All end fittings feature a soft rubberisedmoulded cap, designed to withstandhigh impact without causing damage.
Standard travellers run onprecision ground delrin balls.
A Torlon ball package is offeredwhere higher load applications arerequired. Torlon balls give up to40% more load bearing capacity.These packages are availablein all three sizes and for longor short travellers.
Double take off travellersWith either shackle or toggleattachments, these allow coarse/finetune mainsheet systems to be achieved.They can also be used with a link plate(page 27) to allow for increasedrolling load with the longer cars.
Control line sheavesIn sizes 2 and 3 these feature ourlow friction large diameter ballbearing sheave system.
Shackle take offFeature a high load forgedstainless steel pivoting shackle.
Toggle take offFeatures a solid cast stainless steelupstand with a soft rubber anti-tumblebearing fitted, preventing damage whenblocks are not under load. These takeoffs accept the swivel post from ourcruiser blocks and help achieve atruly low profile system.
Cam cleatsFrom our Kevlar ‘K’ cam range.
See page 48 for full details.
2:1 purchase system
3:1 purchase system
4:1 purchase system;cleating on end fittings
4:1 purchase system;cleating on traveller
Towable genoa carsAvailable in three sizes for yachts up to 14m LOA (46ft)– all three run on the three track profiles available.
2:1, 3:1 and 4:1 systems can beachieved with the unique Bartonmodular system. Modular componentsare listed on the following 6 pages.
Featuring a precision-turnedErtalyte sheave running on a largediameter bearing.
The bolt-through sheave design notonly looks good, but gives addedstrength to these rugged units.
Technical Length Length Weight Weight Width with Height Height MaxDetails single take off double take off single take off double take off Width control line 2:1 4:1 SWL control line
mm mm g g mm cleats mm mm mm kg Ø mm
TravellersSize 1 132 204 252 411 57 98 30 43 500 6
Size 2 166 254 547 923 70 120 44 57 700 8
Size 3 198 292 872 1378 87 130 47 65 1000 8
Length Weight Width Height SWL Sheave Ø Sheave widthmm g mm mm kg mm mm
Genoa carsSize 1 118 400 57 97 500 50 36
Size 2 145 775 70 116 700 60 36
Size 3 170 1181 87 133 1000 70 45
Width with Height Height MaxLength Weight Width control line 2:1 4:1 control line
mm g mm cleats mm mm mm Ø mm
End fittingsSize 1 67 117 59 100 39 50 6
Size 2 88 234 72 127 50 65 8
Size 3 96 362 85 137 60 74 8
Length Weight Width Sheave Ø Max control linemm g mm mm Ø mm
Control line sheave cageSize 1 41 15 38 20 6
Size 2 52 27 49 30 8
Size 3 65 42 57 35 8 23control the power
ma
insheet & g
enoa ca
r systems
Recirculating ball bearing genoa car systems
Important note: boat sizesSuggested boat sizes are given as a guidance only and assume a monohullwith boom end sheeting, loaded vertically to the traveller.Mid-boom sheeting, severely angled take offs and curved tracks can impose greaterloads and suitable allowances should be made for this. If at all unsure of your choiceit is important to seek further advice.If you are close to the maximum boat size suggested, we would advise upgradingto a torlon package, long car or the next size up.
2:1 purchase system
4:1 purchase system
control the power
ma
insh
eet &
gen
oa c
ar s
yste
ms
24
Complete pack recirculating ball bearing traveller systems
Important note: boat sizesSuggested boat sizes are givenas guidance only and assume amonohull with boom end sheeting,loaded vertically to the traveller.
Mid-boom sheeting and severelyangled take offs can impose greaterloads and suitable allowances shouldbe made for this. If at all unsure ofyour choice it is important to seekfurther advice.
If you are close to the maximumboat size suggested, we would adviseupgrading to the next size up.
Complete pack kits are not suitable foropen span applications as they requirebeam section track – see page 29.
Guide to choice of size:
Size 1 for yachts up to 8.5m (28.5ft)
Size 2 for yachts up to 11.0m (36ft)
Pre-packaged mainsheet systems with all components required in onecomplete kit – sliding bolt track, traveller, end fittings, plastic end caps, pilottrack and full fitting instructions.
Travellers, end fittings and track are all extruded from top quality marine gradealuminium and finished in our unique ‘Spectro’ grey anodised finish.
Sliding bolt track allows for a smooth, clean profile and also makes retro-fittingeasier as bolts can be slid along the extrusion to match existing fastening holes.
• Two sizes – for yachts up to 11m LOA (36ft)
• 2:1 or 4:1 purchase systems
• Recirculating precision ground delrin ball system.
Specifications Size 1 Size 2
Max boat size 8.5m 11.0m28.5ft 36ft
Track width 20mm 26mm
Track length 1.4m 1.6m
Max control line Ø 6mm 8mm
SWL 500kgs 700kgs
Fastenings 5mm 6mm
2:1 Purchase Kitwith cleats at 70° on end fittings
• 1.4m (size 1) /1.6m (size 2)sliding bolt track
• Traveller car with singleshackle take off
• End fittings (pair)• Plastic end caps (pair)• Pilot track & fitting instructions.
Size 1 Size 2
20 900 24 900
4:1 Purchase Kitwith cleats at 70° on end fittings
• 1.4m (size 1) /1.6m (size 2)sliding bolt track
• Traveller car with singleshackle take off
• End fittings (pair)• Plastic end caps (pair)• Pilot track & fitting instructions.
Size 1 Size 2
20 901 24 901
4:1 Purchase Kitincorporating cleats on traveller • 1.4m (size 1) /1.6m (size 2)
sliding bolt track• Traveller car with single
shackle take off• End fittings (pair)• Plastic end caps (pair)• Pilot track & fitting instructions.
Size 1 Size 2
20 902 24 902
24 900
24 901
24 902
25www.bartonmarine.com
ma
insheet & g
enoa ca
r systems
Traveller Carwith single shackle take offand internal control line sheaves
Size 1 Size 2 Size 3
20 101 24 101 30 101
see page 23 for specifications.
Modular Components for recirculating ball bearing traveller systems
• Recirculating precision grounddelrin ball system
• Three sizes for yachts up to 14mLOA (46ft)
• Build your choice of traveller,cleating system and end fittings.
Guide to choice of size:
Size 1 for yachts up to 8.5m (28.5ft)
Size 2 for yachts up to 11.0m (36ft)
Size 3 for yachts up to 14.0m (46ft)
Important note: boat sizesSuggested boat sizes are given as a guidance only and assume amonohull with boom end sheeting, loaded vertically to the traveller.Mid-boom sheeting, severely angled take offs and curved trackscan impose greater loads and suitable allowances should be madefor this. If at all unsure of your choice it is important to seekfurther advice.If you are close to the maximum boat size suggested, we wouldadvise upgrading to a torlon package, long car or the next size up.
Choose the individual components required to build the system of your choice which is the most suitable for your boat.See pages 26-28 for pre-designed combinations available.
Traveller Carwith double shackle take offand internal control line sheaves
Size 1 Size 2 Size 3
20 103 24 103 30 103
see page 23 for specifications.
Traveller Carwith single toggle take offand internal control line sheaves
Size 1 Size 2 Size 3
20 105 24 105 30 105
see page 23 for specifications.
End Fittingwith integral sheaves(supplied in pairs).
Size 1 Size 2 Size 3
20 110 24 110 30 110
see page 23 for specifications.
Traveller Carwith double toggle take offand internal control line sheaves
Size 1 Size 2 Size 3
20 107 24 107 30 107
see page 23 for specifications.
Genoa CarWith integral sheaves(2:1, 3:1 or 4:1)
Size 1 Size 2 Size 3
20 300 24 300 30 300
see page 23 for specifications.
End Fittingwith cleat at 90° to track(supplied in pairs).
Size 1 Size 2 Size 3
20 113 24 113 30 113
see page 23 for specifications.
End Fittingwith cleat at 70° to track(supplied in pairs).
Size 1 Size 2 Size 3
20 114 24 114 30 114
see page 23 for specifications.
Traveller CleatPlate Assembly(supplied in pairs)
Size 1 Size 2 Size 3
20 117 24 117 30 117
Control LineSheave Cagefor use on travellersand end fittings(supplied in pairs)
Size 1 Size 2 Size 3
20 112 24 112 30 112
see page 23 for specifications.
www.bartonmarine.com
ma
insh
eet &
gen
oa c
ar s
yste
ms
26
The unique Barton modular system allows a wide variety of systems to be constructed, giving multiplecontrol line options.In the following tables, order both part numbers listed (where appropriate) for the traveller illustrated.
Travellers recirculating ball bearing – single take off
Traveller Carwith single shackle take off andintegral control line sheaves 2:1 or 3:1 purchase.
Size 1 Size 2 Size 3
20 101 24 101 30 101
Traveller Carwith single toggle take off andintegral control line sheaves 2:1 or 3:1 purchase.
Size 1 Size 2 Size 3
20 105 24 105 30 105
Genoa CarWith integral controlline sheaves2:1 or 3:1
Size 1 Size 2 Size 3
20 300 24 300 30 300
see page 23 for specifications.
Traveller Carwith single shackle take off 4:1 purchase. Comprises:-
Size 1 Size 2 Size 3
20 101 24 101 30 101
20 112 24 112 30 112Order both part numbers to achievethe product shown.
Traveller Carwith single toggle take off 4:1 purchase. Comprises:-
Size 1 Size 2 Size 3
20 105 24 105 30 105
20 112 24 112 30 112Order both part numbers to achievethe product shown.
Traveller Carwith cleats and singleshackle take off 4:1 purchase. Comprises:-
Size 1 Size 2 Size 3
20 101 24 101 30 101
20 117 24 117 30 117Order both part numbers to achievethe product shown.
Traveller Carwith cleats and singletoggle take off 4:1 purchase. Comprises:-
Size 1 Size 2 Size 3
20 105 24 105 30 105
20 117 24 117 30 117Order both part numbers to achievethe product shown.
Genoa CarWith integral control line sheaves(4:1) Comprises:-
Size 1 Size 2 Size 3
20 300 24 300 30 300
20 112 24 112 30 112Order both part numbers to achievethe product shown.
27control the power
ma
insheet & g
enoa ca
r systems
Travellers recirculating ball bearing – double take off
Traveller Carwith double shackle take off 4:1 purchase. Comprises:-
Size 1 Size 2 Size 3
20 103 24 103 30 103
20 112 24 112 30 112Order both part numbers to achievethe product shown.
Traveller Carwith double shackle take offand integral control line sheaves
2:1 or 3:1 purchase.
Size 1 Size 2 Size 3
20 103 24 103 30 103
Traveller Carwith double toggle take offand integral control line sheaves
2:1 or 3:1 purchase.
Size 1 Size 2 Size 3
20 107 24 107 30 107
Traveller Carwith double toggle take off 4:1 purchase. Comprises:-
Size 1 Size 2 Size 3
20 107 24 107 30 107
20 112 24 112 30 112Order both part numbers to achievethe product shown.
Traveller Carwith cleats and doubleshackle take off 4:1 purchase. Comprises:-
Size 1 Size 2 Size 3
20 103 24 103 30 103
20 117 24 117 30 117Order both part numbers to achievethe product shown.
Traveller Carwith cleats and doubletoggle take off 4:1 purchase. Comprises:-
Size 1 Size 2 Size 3
20 107 24 107 30 107
20 117 24 117 30 117Order both part numbers to achievethe product shown.
Link PlateFor long double toggle take off cars.Heavy-duty stainless plate that spanstoggles - for heavy-duty applications.
Size 1 Size 2 Size 3
20 202 24 202 30 202
control the power
ma
insh
eet &
gen
oa c
ar s
yste
ms
28
The unique Barton modular system allows a wide variety of systems to be constructed, giving multiple control lineand cleating options for track end fittings.In the following tables, order both part numbers listed (where appropriate) for the end fitting illustrated.
End Fittings recirculating ball bearing
End Fitting4:1 purchase.
(supplied as a pair of each p/no.).
Size 1 Size 2 Size 3
20 110 24 110 30 110
20 112 24 112 30 112Order both part numbers to achievethe product shown.
End Fittingwith cleat at 90°2:1 or 3:1 purchase.
(supplied as a pair of each p/no.).
Size 1 Size 2 Size 3
20 110 24 110 30 110
20 113 24 113 30 113Order both part numbers to achievethe product shown.
End Fitting2:1 or 3:1 purchase.
(supplied in pairs).
Size 1 Size 2 Size 3
20 110 24 110 30 110
see page 23 for specifications.
End Fittingwith cleat at 70°2:1 or 3:1 purchase.
(supplied as a pair of each p/no.).
Size 1 Size 2 Size 3
20 110 24 110 30 110
20 114 24 114 30 114Order both part numbers to achievethe product shown.
End Fittingwith cleat at 90°4:1 purchase.
(supplied as a pair of each p/no.).
Size 1 Size 2 Size 3
20 110 24 110 30 110
20 113 24 113 30 113
20 112 24 112 30 112Order all part numbers to achievethe product shown.
End Fittingwith cleat at 70°4:1 purchase.
(supplied as a pair of each p/no.).
Size 1 Size 2 Size 3
20 110 24 110 30 110
20 114 24 114 30 114
201 12 24 112 30 112Order all part numbers to achievethe product shown.
Torlon BallsTorlon ball packages available for all traveller sizes:
Size 1 Size 2 Size 3short long short long short long
20 200 20 201 24 200 24 201 30 200 30 201
Crash Stopfor genoa track.
(supplied in pairs).
Size 1 Size 2 Size 3
20 310 24 310 30 310
29www.bartonmarine.com
ma
insheet & g
enoa ca
r systems
Per metre or in set lengths – choose fromthe adjacent table.Hollow section extruded aluminium track for light weight yetretaining high load capacity.
‘Spectro’ grey anodised finish is extremely durable and addsto the friction-free efficient performance of these products.
Size 1 Size 2 Size 3
Drilled trackper metre 20 000 24 000 30 000
0.6 metre 20 010 24 010 30 010
1.2 metre 20 020 24 020 30 020
1.8 metre 20 030 24 030 30 030
2.4 metre 20 040 24 040 30 040
3.0 metre 20 050 24 050 30 050
5.0 metre 20 060 24 060 30 060
End cap (pair) 20 001 24 001 30 001
Sliding bolt trackper metre 20 002 24 002 30 002
0.6 metre 20 012 24 012 30 012
1.2 metre 20 022 24 022 30 022
1.8 metre 20 032 24 032 30 032
2.4 metre 20 042 24 042 30 042
3.0 metre 20 052 24 052 30 052
5.0 metre 20 062 24 062 30 062
End cap (pair) 20 001 24 001 30 001
Beam trackper metre 20 003 24 003 30 003
0.6 metre 20 013 24 013 30 013
1.2 metre 20 023 24 023 30 023
1.8 metre 20 033 24 033 30 033
2.4 metre 20 043 24 043 30 043
3.0 metre 20 053 24 053 30 053
5.0 metre 20 063 24 063 30 063
End cap (pair) 20 100 24 100 30 100
Track 20mm/26mm/30mm
Drilled trackThe most commonly used, drilled andcountersunk at 100mm centres, withthe first hole at 50mm from track end.
Specifications Size 1 Size 2 Size 3
Width 20mm 26mm 30mm
Height 12mm 15mm 18mm
Fastenings 5mm 6mm 8mm
Sliding bolt trackTo allow for a smooth profile with no visiblefastenings. Also makes retro fit an easier job,as bolts can be slid along the extrusion tomatch existing fastening holes.
Ensure washers are fitted beneath track to ensure a good seal(see diagram).
Specifications Size 1 Size 2 Size 3
Width 20mm 26mm 30mm
Height 12mm 16.5mm 19mm
Fastenings 5mm 6mm 8mm
Beam trackUse beam track when spanning cockpits or companionway hatches,where unsupported length is required. A minimum of threefastenings should be used on either side of the unsupported length– place fastenings at 100mm centres in supported sections.
Ensure washers are fitted under the head of the bolt and betweentrack & deck to ensure a secure seal (see diagram).
Specifications Size 1 Size 2 Size 3
Max unsupported 400mm 700mm 800mmlength
Width W 20mm 26mm 30mm
Width W2 26mm 34mm 40mm
Height 27mm 34.5mm 40.5mm
Fastenings 6mm 8mm 10mm
Apply sealant
Fittingslidingbolt track
Fittingbeamtrack
Curved trackSome curving oftrack can beaccommodated,depending onwhich traveller/genoa caris selected.
Please contact usfor further advice.
24 000
24 003
24 002
20 001
24 100
Three styles of track are available– drilled, sliding bolt and beam:-
Part End Length Width Break SWL WeightNo. Fitting mm mm Load kg kg g
19mm traveller cars4 wheels plain 19 100 19900 52 38 1200 600 127
4 wheels, control line eyes 19 101 19 902 52 38 1200 600 136
4 wheels, control line sheaves 19 102 19902 52 38 1000 500 152
4 wheels, control cleats & sheaves 19 103 19902 122 75 1000 500 339
6 wheels, control line sheaves 19 105 19 902 85 38 2240 1120 284
Part Length Width WeightNo. mm mm g
19mm track end fittings (pairs)Adjustable plunger stops 19 900 38 29 83
Plastic track end 19 901 16
End fitting - horizontal sheave 19 902 45 22 44
www.bartonmarine.com
I sec
tion
track
&tra
velle
rs
30
19mm ‘I’ section track & travellers
19 000
19mm ‘I’ section trackExtruded with a hollow section for lightweight and high load capacity.
Drilled for fastenings and plunger stops.
Supplied in metric lengths as shownin the table below.
Specifications & dimensions
Width W 19mm
Height 24mm
Width X 11mm
Fastenings Ø 5mm
Fastening centres 100mm
Plunger hole centres 50mm
Weight 479g per m
for yachts up to 7.3m (24ft) LOAA comprehensive range of traveller systems suitable for use on dinghies,dayboats and light cruising yachts.
Also ideal for use in self-tacking jib systems on larger yachts and catamarans.
Manufactured from marine grade aluminium and stainless steel. ‘I‘ sectiontrack is silver anodised. Fittings are black anodised.
• Stainless steel captive bearing ball race wheels
• Rugged, lightweight ‘I’ section track
• Various control line options
• Cam cleat versions feature ‘K cam’ Kevlar cleats.
PartNo.
19mm I section trackper metre 19 000
0.6 metre 19 010
1.2 metre 19 020
1.8 metre 19 030
2.4 metre 19 040
3.0 metre 19 050
5.0 metre 19 060
Track end cap (pair) 19 901
19 900
19 902
19 103
19 100
19 101
19 105
19 102
19 901
Curved track‘I‘ section track canbe custom curved tospecial requirements.Please enclose adetailed drawingwhen ordering,giving all dimensionsof curvature.
31control the power
Isection track &
travellers
Part End Length Width Break SWL WeightNo. Fitting mm mm Load kg kg g
24mm traveller cars4 wheels plain 26 101 26900 69 47 2560 1280 257
4 wheels, control line sheave 26 102 26110 69 47 2560 1280 287
6 wheels, control blocks 2:1 purchase 26 103 26110+26902 226 47 3000 1500 560
6 wheels, control blocks 3:1 purchase 26 104 26111+26902 245 47 3000 1500 566
Part Length Width WeightNo. mm mm g
24mm track end fittings (pairs)End fitting with sheave & cleat 26 110 90 75 412
End fitting with double sheave & cleat 26 111 90 75 96
Adjustable plunger stops 26 900 32 30 64
Plastic track end 26 901 20
Crash stop 26 902 32 30 36
24mm ‘I’ section track & travellers
Important note: boat sizesSuggested boat sizes are given asguidance only and assume a monohullwith boom end sheeting, loaded verticallyto the traveller.
Mid-boom sheeting and severely angledtake offs can impose greater loads andsuitable allowances should be made forthis. If at all unsure of your choice it isimportant to seek further advice.
Crash stops should be used to preventcars from damaging track and end fittings.
26000
24mm ‘I’ section trackExtruded with a hollow section for light weightand high load capacity.
Silver anodised drilled for fastenings andplunger stops.
Supplied in metric lengths as shown in the table.
Specifications & dimensions
Width W 24mm
Height 28mm
Width X 16mm
Fastenings Ø 5mm
Fastening centres 100mm
Plunger hole centres 50mm
Weight 721g per m
for yachts up to 10.7m (35ft) LOAA mid range of traveller systems, manufactured from marine grade aluminiumand stainless steel. All feature heavy-duty attachments. Control line blocks (wherefitted) have low friction ball bearing sheaves, accepting lines up to 8mm diameter.‘I‘ section track is silver anodised. Fittings are black anodised.
End fittings are secured through track with track fastening bolts.
• Heavy duty take off attachments
• Four and six wheel options
• Stainless steel captive bearing ball race wheels
• Ball bearing control line blocks
• End fittings give varied control line options
• Cam cleat versions feature ‘K cam’ Kevlar cleats.
PartNo.
24mm I section trackper metre 26 000
0.6 metre 26 010
1.2 metre 26 020
1.8 metre 26 030
2.4 metre 26 040
3.0 metre 26 050
5.0 metre 26 060
Track end cap (pair) 26 901
26101
26 102
Curved track‘I’ section track canbe custom curved tospecial requirements.Please enclose adetailed drawingwhen ordering,giving all dimensionsof curvature.
26902
26 900
26 901
26 110
26 103
26 104
26 111
I sec
tion
track
&tra
velle
rs
32
28mm ‘I’ section trackExtruded with a hollow section for lightweight and high load capacity.Drilled for fastenings and plunger stops.Supplied in metric lengths as shown inthe table below.
Specifications & dimensions
Width W 28mm
Height 34mm
Width X 17mm
Fastenings Ø 6mm
Fastening centres 100mm
Plunger hole centres 50mm
Weight 1041g per m
for yachts up to 15m (50ft) LOAA range of traveller systems for larger yachts up to 15m LOArunning on our heavy-duty track. Four and six wheel travellersshould be used on boats up to approximately 12m LOA;the eight wheel models are for larger craft. Please seenote marked *.
All feature heavy-duty attachments, through-bolted for addedsecurity. Control line blocks (where fitted) have low frictionball bearing sheaves, accepting lines up to 10mm diameter.‘I‘ section track is silver anodised. Fittings are black anodised.
End fittings are secured through track with trackfastening bolts.
Part End Length Width Break SWL WeightNo. Fitting mm mm Load kg kg g
28mm traveller cars4 wheels plain 28 101 28900 88 54 2522 1250 438
4 wheels, control line sheaves 28 102 28110 88 54 2500 1250 472
6 wheels, control blocks 2:1 purchase 28 103 28110+28902 245 54 3400 1700 850
6 wheels, control blocks 3:1 purchase 28 104 28111+28902 272 55 3400 1700 864
6 wheels, control blocks 4:1 purchase 28 105 28112+28902 245 55 3400 1700 951
Part Length Width WeightNo. mm mm g
28mm track end fittings (pairs)End fitting with sheave, becket & cleat 28 110 108 90 620
End fitting with double sheave & cleat 28 111 108 90 716
End fitting with double sheave, becket & cleat 28 112 108 90 724
Adjustable plunger stops 28 900 35 34 112
Plastic track end 28 901 42
Crash stop 28 902 35 34 76
Curved track‘I’ section track canbe custom curved tospecial requirements.Please enclose adetailed drawingwhen ordering,giving all dimensionsof curvature.
28 10528 112
PartNo.
28mm I section trackper metre 28 000
0.6 metre 28 010
1.2 metre 28 020
1.8 metre 28 030
2.4 metre 28 040
3.0 metre 28 050
5.0 metre 28 060
Track end cap (pair) 28 901
28 104
28 111
28 103
28 110
28 101
control the power
28mm ‘I’ section track & travellers
• Stainless steel captivebearing ball race wheels
• Four, six and eightwheeled options
• Rugged, lightweight‘I’ section track
• Cam cleat versions feature‘K’ cam Kevlar cleats
• End fittings give variedcontrol line options
• Ball bearing control line blocks.
*Note: for yachts over 12 metres our eight wheeled travellers must be used.These are made to order so please state requirements when ordering.
28 102
28 000
28 902
28 900
28 901
Important note: boat sizesSuggested boat sizes are givenas guidance only and assume amonohull with boom end sheeting,loaded vertically to the traveller.
Mid-boom sheeting and severelyangled take offs can impose greaterloads and suitable allowancesshould be made for this. If atall unsure of your choice it isimportant to seek further advice.
Crash stops should be used toprevent cars from damagingtrack and end fittings.
33
sliders &
genoa
cars for T tra
ck
www.bartonmarine.com
20mm ‘T’ section track, sliders, genoa cars
Part Length Width Height Sheave Ø Max Rope Ø Break SWL WeightNo. mm mm mm mm mm Load kg kg g
Genoa cars & towable genoa carsGenoa car 22 100 60 34 65 30 10 1160 580 119
Towable genoa car 22 200 110 34 65 30 10 1160 580 127
Towable genoa car 2:1 purchase 22 220 138 34 65 30 10 1160 580 160
Towable car end fittingsTrack end 22 210 80 32 36 30 8 – – 97
Track end + becket 22 221 80 32 47 30 8 – – 99
Mainsheet/genoa slides & stopsMainsheet slide 22 300 60 32 35 – – 1200 600 55
Genoa slide 22 301 60 32 35 – – 1200 600 68
Plunger stop 22 900 30 32 30 – – – – 30
Bullseye & fairlead slidesBullseye slide 22 310 80 32 60 – 14 400 200 150
Fairlead slide 22 311 90 32 42 – 12 400 200 102
Stand up blockStand up block 22 312 75 32 115 35 8 740 370 195
Track end caps (pair)Track end caps (supplied in pairs) 22 901 20 – – – – – – 55
20mm ‘T’ section trackFor use with all slidersfeatured on this page.Drilled for fastenings andplunger stops. ‘Spectro’grey anodised and suppliedin metric lengths.
Specifications & dimensions
Width W 20mmWidth X 11mm
Height H 8mmHeight J 2.5mm
Fastenings Ø 5mm
Fastening centres 100mm
Plunger hole centres 50mm
Weight 270g per m
Plain bearing genoa cars and slidersA lightweight and compact range of plain bearingextruded aluminium sliders, running on 20mm (3/4”)‘T’ track and finished in our unique ‘Spectro’ greyanodised finish.
This useful range will find a wide variety ofapplications on larger dinghies, dayboats andlight cruiser/racers.
PartNo.
20mm T section trackper metre 22 000
0.6 metre 22 010
1.2 metre 22 020
1.8 metre 22 030
2.4 metre 22 040
3.0 metre 25 050
5.0 metre 22 060
Track end caps (pair) 22 901
22 312
22 901
22 900
22 221
22 220
22 300
22 200
22 310
22 311
22 100
22 301
22 210
22 000
Genoa car withplunger stopFeatures a precision turned Ertalytesheave, through-bolted for extrastrength. The positive actionplunger mechanism has aneasy-grip knob.
Towable genoa carsWith tow eye or sheave in place ofplunger, allowing a control line tobe lead aft so that genoa caradjustments can be made fromthe cockpit. Use in conjunctionwith end fittings shown.
Genoa andmainsheet slidesA strong unit which will acceptmost Barton blocks – with astainless steel attachment loop,through-bolted for strength.
Bullseye slideWith a swivelling bullesye that willalways accommodate the correctangle of sheeting. Accepts linesup to 14mm diameter. A stainlesssteel insert is provided toprevent wear.
Fairlead slideFeatures a plain moulded plasticfairlead fitted to an adjustableslide. Accepts lines up to 12mmdiameter; not suitable forhigh loads.
Stand up blockHas a stainless eye fitted to astainless loop, through-bolted forstrength. The moulded plasticspring/gaiter prevents the blocktumbling or ropes snagging.Supplied with a size 2 blockaccepting lines up to8mm diameter.
Plunger stopsFor use with mainsheet orgenoa track sliders. Sold singly.
slid
ers
&g
enoa
ca
rs fo
r T tr
ack
34
Plain bearing genoa cars, sliders andspinnaker pole slides
A popular range of genoa cars and sliders designed to run on25mm (1”) ‘T’ track. All are manufactured from high qualitymarine grade aluminium and finished with our unique‘Spectro’ grey anodised finish for added protection.
All cars and sliders featured on these pages have mouldednylon inserts to ensure free, smooth running under load andprevent damage to finish or potential corrosion.
• ‘Spectro’ grey anodised finish
• Stainless plunger stops with positive action
• Moulded nylon slide inserts ensure free running
• Large, easy-grip plunger knobs.
Important note – foot blocks:Fastenings of the minimum diameter suggested should be used to gain full load capacity. Ensure that suitable mounting pads are provided underdeck. Stacking blocks to achieve doubles will severely reduce working loads quoted.
www.bartonmarine.com
25mm ‘T’ section track, sliders, genoa cars
25mm ‘T’ section trackFor use with all sliders featuredon this page. Drilled forfastenings and plunger stops.‘Spectro’ grey anodised andsupplied in metric lengths.
Specifications & dimensions
Width W 25mm
Width X 14mm
Height H 10mm
Height J 4mm
Fastenings Ø 5mm
Fastening centres 100mm
Plunger hole centres 50mm
Weight 441g per m
25 000
25 900
Part Sheave Sheave Rope Break SWL Length Fastenings WeightNo. Ø mm width mm Ø mm Load kg kg mm mm g
Foot blocksFoot block – 50mm 82 995 50 15 12 1000 500 79 3 x M6 114
Foot block – 65mm 82 996 65 18 16 1600 800 100 2 x M6/1 x M8 211
Foot block – 85mm 82 997 85 21 18 3000 1500 132 2 x M8/1 x M10 427
Foot blocksDesigned for use with the genoa cars shown in this range,these strong foot blocks have a three-bolt fixing and can bestacked to achieve doubles (see note below). ‘Spectro’grey finish. Precision turned Ertalyte sheaves run on largediameter centre bearing to give low friction performanceunder high loads.
See page 21 for further details and our foot blockwith cam range.
25 901
82 996 82 995
25 220
25 100
25 200
25 221
25 210
35
sliders &
genoa
cars for T tra
ck
control the power
25mm ‘T’ section track, sliders, genoa cars
Part Length Width Height Sheave Ø Max Rope Ø Break SWL WeightNo. mm mm mm mm mm Load kg kg g
Genoa cars & towable genoa carsGenoa car 25 100 80 42 87 40 2 x 12 2280 1140 247
Towable genoa car 25 200 127 42 87 40 2 x 12 2280 1140 258
Towable genoa car 2:1 purchase 25 220 170 42 87 40 2 x 12 2280 1140 297
Towable car end fittingsTrack end 25 210 88 37 35 35 8 – – 116
Track end + becket 25 221 88 37 50 35 8 – – 121
Mainsheet/genoa slides & stopsMainsheet slide 25 300 80 42 42 – – 2860 1430 111
Genoa slide 25 301 80 42 40 – – 2860 1430 123
Plunger stop 25 900 30 33 34 – – – – 36
Bullseye slideBullseye slide 25 303 80 42 60 – 14 – – 184
Stand up blocksStand up block – size 3 25 310 80 42 120 45 10 980 490 223
Stand up block – size 4 25 311 80 42 142 57 12 1580 790 312
Track end caps (pair)Track end caps (supplied in pairs) 25 901 23 – – – – – – 11
PartNo.
25mm T section trackper metre 25 000
0.6 metre 25 010
1.2 metre 25 020
1.8 metre 25 030
2.4 metre 25 040
3.0 metre 25 050
5.0 metre 25 060
Track end caps (pair) 25 901
Part Length Width Height Eye internal WeightNo. mm mm mm Ø mm g
Spinnaker pole slidesSpinnaker pole slide 25 302 80 42 74 35 237
Towable spinnaker pole slide 25 304 80 42 74 35 253
25 310
25 311
25 300
25 301
25 303
25 304
25 302
Genoa car with plunger stopsFeatures precision turned Ertalyte sheaves running ona large diameter centre bearing, for friction-freeperformance under load. Sheaves are designed withextra width to accept two sheets. The sheave axle isthrough-bolted and riveted for extra strength.
Towable genoa carsWith tow eye or sheave in place of plunger, allowing acontrol line to be lead aft so that genoa car adjustmentscan be made from the cockpit. Use in conjunction withend fittings shown.
Genoa and mainsheet slidesHave a heavy duty stainless steel attachment loop,through-bolted and riveted for extra strength. These unitswill accept most Barton blocks featured on pages 6-17.
Bullseye slideFeatures a swivelling bullseye that will alwaysaccommodate the correct angle of sheeting. A stainlesssteel insert is provided to prevent wear. Accepts linesup to 14mm diameter.
Spinnaker pole slideHave a heavy duty stainless steel ring welded to anattachment plate which is through-bolted to the slide.Generous ring opening to accept most pole ends.Towable spinnaker pole slide has eyes fitted toboth ends of the slide for the attachment of control lines.Use with 25 210 end fittings.
Stand up blocksHave a stainless steel eye fitted to a stainless steel loop,through-bolted for strength. The moulded plastic spring/gaiter prevents the block tumbling or ropes snagging.Two sizes are available – for 10mm and 12mm lines.
slid
ers
&g
enoa
ca
rs fo
r T tr
ack
36
Plain bearing genoa cars, slidersand spinnaker pole slides, plusstand up blocks
A popular range of genoa cars and sliders designed to runon 32mm (11/4”) ‘T’ track. All are manufactured from highquality marine grade aluminium and finished with ourunique ‘Spectro’ grey anodised finish for added protection.
All cars and sliders featured on these pages have mouldednylon inserts to ensure free, smooth running under loadand prevent damage to finish or potential corrosion.
All genoa cars in this range are available in a heavy-dutyversion for larger craft or for larger load applications.
• ‘Spectro’ grey anodised finish
• Stainless steel plunger stops with positive action
• Moulded nylon slide inserts ensure free running
• Large, easy-grip plunger knobs
• Heavy-duty genoa car options.
control the power
32mm ‘T’ section track, sliders, genoa cars
32mm ‘T’ section trackFor use with all sliders featuredon this page. Drilled forfastenings and plunger stops.‘Spectro’ grey anodised andsupplied in metric lengths.
Specifications & dimensions
Width W 32mm
Width X 20mm
Height H 15mm
Height J 5mm
Fastenings Ø 6mm
Fastening centres 100mm
Plunger hole centres 50mm
Weight 756g per mtre
32 000
32 900
Part Sheave Sheave Rope Break SWL Length Fastenings WeightNo. Ø mm width mm Ø mm Load kg kg mm mm g
Foot blocksFoot block – 50mm 82 995 50 15 12 1000 500 79 3 x M6 114
Foot block – 65mm 82 996 65 18 16 1600 800 100 2 x M6/1 x M8 211
Foot block – 85mm 82 997 85 21 18 3000 1500 132 2 x M8/1 x M10 427
32 901
82 996 82 995
32 100
32 221
32 220
32 101
32 200
32 201
32 211
Important note – foot blocks:Fastenings of the minimum diametersuggested should be used to gain fullload capacity. Ensure that suitablemounting pads are provided underdeck. Stacking blocks to achievedoubles will severely reduceworking loads quoted.
32 210
Foot blocksDesigned for use withthe genoa cars shown inthis range, these strongfoot blocks have athree-bolt fixing and canbe stacked to achievedoubles (see note below).‘Spectro’ grey finish. Precisionturned Ertalyte sheaves run on largediameter centre bearing to give low frictionperformance under high loads.See page 21 for further details and our foot block with cam range.
32 301
Part Length Width Height Eye internal WeightNo. mm mm mm Ø mm g
Spinnaker pole slidesSpinnaker pole slide 32 302 109 52 80 40 357
Towable spinnaker pole slide 32 304 109 52 80 40 359
37
sliders &
genoa
cars for T tra
ck
www.bartonmarine.com
32mm ‘T’ section track, sliders, genoa cars
Part Length Width Height Sheave Ø Max Rope Ø Break SWL WeightNo. mm mm mm mm mm Load kg kg g
Genoa cars & towable genoa carsGenoa car 32 100 109 52 102 50 2 x 16 3280 1640 469
Genoa car – heavy-duty 32 101 127 55 117 60 2 x 16 5970 2985 728
Towable genoa car 32 200 170 52 102 50 2 x 16 3280 1640 503
Towable genoa car – heavy-duty 32 201 190 55 117 60 2 x 16 5970 2985 749
Towable genoa car 2:1 purchase 32 210 220 52 102 50 2 x 16 3280 1640 561
Towable genoa car 2:1 purchase – heavy-duty 32 211 235 55 117 60 2 x 16 5970 2985 820
Towable car end fittingsTrack end 32 220 109 47 44 45 10 – – 230
Track end + becket 32 221 109 47 58 45 10 – – 236
Mainsheet/genoa slides & stopsMainsheet slide 32 300 109 52 50 – – 2980 1490 231
Genoa slide 32 301 109 52 50 – – 2980 1490 254
Plunger stop 32 900 35 42 40 – – – – 70
Stand up blocksStand up block – size 5 32 310 109 52 150 54 12 1800 900 450
Stand up block – size 6 32 311 109 52 165 60 12 2300 1150 489
Stand up block – size 7 32 312 109 52 170 72 14 2800 1400 565
Track end caps (pair)Track end caps (supplied in pairs) 32 901 29 – – – – – – 19
PartNo.
32mm T section trackper metre 32 000
0.6 metre 32 010
1.2 metre 32 020
1.8 metre 32 030
2.4 metre 32 040
3.0 metre 32 050
5.0 metre 32 060
Track end caps (pair) 32 901
Genoa cars with plunger stopsFeature precision turned Ertalyte sheaves running ona large diameter centre bearing, for friction-freeperformance under load. Sheaves are designed withextra width to accept two sheets. The sheave axle isthrough-bolted and riveted for extra strength.
Towable genoa carsWith tow eye or sheave in place of plunger, allowing acontrol line to be lead aft so that genoa car adjustmentscan be made from the cockpit. Use in conjunction withend fittings shown.
Genoa and mainsheet slidesWith a heavy-duty stainless steel attachment loop,through-bolted and riveted for extra strength. These unitswill accept most Barton blocks featured on pages 6-17.
Spinnaker pole slideHas a heavy duty stainless steel ring welded to anattachment plate which is through-bolted to the slide.Generous ring opening to accept most pole ends.
Towable spinnaker pole slide has eyes fitted toboth ends of the slide for the attachment of control lines.Use with 32 220 end fittings.
Stand up blocksHave a stainless steel eye fitted to a stainless steelloop, through bolted for strength. The mouldedplastic spring/gaiter prevents the block tumbling orropes snagging. Three sizes are available – for linesup to 14mm.
32 311
32 310
32 304
32 302
32 300
32 312
Rope clutchesManufactured from high grade plastics and aluminium with ‘Spectro’grey anodised finish.
Lines can be drawn through the clutch in the locked position as the linemoves freely in the direction of pull and is restricted from returning bya spring-loaded cam mechanism.
This compact range is suitable for securing halyards and control lineson yachts up to approx 30ft – or for lighter duties on large craft.
dec
kor
ga
nise
rs
www.bartonmarine.com
38
Deck organisers and clutches
Part Length Width Height WeightNo. mm mm mm g
Size 1 deck organisers2-sheave 81 582 115 28 25 108
3-sheave 81 583 157 28 25 155
4-sheave 81 584 200 28 25 200
5-sheave 81 585 244 28 25 244
6-sheave 81 586 287 28 25 295
Size 2 deck organisers2-sheave 81 682 148 38 28 205
3-sheave 81 683 205 38 28 290
4-sheave 81 684 262 38 28 378
5-sheave 81 685 318 38 28 465
6-sheave 81 686 376 38 28 555
Specifications Size 1 Size 2
Sheave Ø 32mm 44mmSheave width 16mm 17mm
Fastenings 6mm 8mm
Max line Ø 12mm 14mm
Hole centres 43mm 58mm
Available in two sheave sizes andin 2, 3, 4, 5 and 6-sheave modelsDesigned for use when leading control lines andhalyards across the coach roof and back tothe cockpit.
This range features aluminium construction with‘Spectro’ grey anodised finish. Sheaves are frommoulded acetal with hollow stainless rivets toallow easy and tidy fitting.
81 586
81 585
815 84
81 582
815 83
80 500
80 501
80 502
Specifications
Max holding capacity 350kg
Max rope capacity 10mm
Fastenings 6mm
Part Length Width Height WeightNo. mm mm mm g
Rope ClutchSingle rope clutch 80 500 107 28 62 250
Double rope clutch 80 501 107 54 62 480
Triple rope clutch 80 502 107 80 62 710
Locking levers comein grey, red andwhite and a set ofmarking stickersis included.
39control the power
clutchesBarton D0550 clutches
An all-new design for cruising andracing yachts, offering a holding powerof up to 550kgs (see chart below).
Modern, high-performance materialsManufactured from modern lightweight materials, the DO550 mouldedparts are from high-grade plastics which are strong, light and impact-resistant. Cams and bases are from marine grade aluminium, ‘Spectro’anodised for long life in the harsh marine environment.
True clutch mechanismThis true clutch mechanism allows line to be adjusted through theunit in the closed, locked position with minimal slippage. Releaseunder load is positive and requires little effort.
The mechanism’s opening and closing action is precise and easy tooperate, even with cold wet hands. A positive handle lock in theclosed position is also featured.
Kind to linesThe clutch’s cam and base, manufactured from high grade extrudedaluminium, feature a specially tempered tooth design which allows formaximum grip with minimal slippage, whilst being kind to your lines.
Stainless steel rope fairleads are fitted to both line entry and exit points;a feature which help to prevent wear to both clutch and lines.
Bolt-together constructionfor straighforward servicingThe DO 550 clutch range features the advantage of a bolt-togetherconstruction which allows for ease of servicing and replacement of parts.A full range of components is available from your Barton stockist.
Ergonomically designed handleThe handle is strong and easy to grip, with a positive smooth lockand unlock action.
A unique feature of this new design is the removable insert on thetop face of the handle. These inserts are available packaged separatelywith a selection for both cruising and racing yachts.
81 540 ‘Cruiser’ insert pack contains: Main, Genoa 1, Spin Halyard 1,Topping Lift, Spin pole up, Spin pole down, Blank.
81 540 ‘Racer’ insert pack contains: Reef 1, Cunningham, Reef 2, Kicker,Mainsheet, Genoa Furling, Genoa 2, Spin Halyard 2, Backstay, Outhaul,Downhaul, Blank.
Specifications
Max holding power 550kg
Rope capacity up to 12mm
Fastening diameter 6mm
Fastening centres 79mm
Important fitting notes: rope clutches
• When fitting ensure a fair lead straight through the clutch to prevent wearto side plates and/or reduced load capabilities.
• For best performance site clutch approximately 2ft (600mm) forward ofthe winch to ensure a fair lead both vertically and horizontally.
• Use Barton deck organisers forward of the clutch to gain perfect alignment.• Always use a bolt-through fastening with a suitable sealant.• A drilling template is provided on our packaging for your convenience.
PartNo.
Printed handle inserts‘Cruiser’ handle insert pack (7 inserts) 81 540
‘Racer’ handle insert pack (12 inserts) 81 541
Spare partsHandle 81 545
Cam 81 546
Base 81 547
Set of 4 x pan head machine screws & nuts 81 548
8mm
10mm
12mm
0 200 400 600
line Ø
DO550 clutches – holding power
kg
Part Length Width Height WeightNo. mm mm mm g
DO550 clutchesSingle DO 550 clutch 81 500 133 38 68 343
Double DO 550 clutch 81 501 133 65 68 544
Triple DO 550 clutch 81 502 133 91 68 754
81 500
81 501
81 502
81 54181 540
control the power
win
ches
& w
inch
ha
ndle
s
40
Winch handles & accessories
Part Length WeightNo. mm g
Aluminium winch handles8” Aluminium handle 21 001 225 290
8” Aluminium handle – locking 21 011 225 302
10” Aluminium handle 21 002 280 335
10” Aluminium handle – locking 21 022 280 347
Floating winch handles10” Floating handle – locking 21 033 290 267
8” Floating handle – locking 21 034 235 306
Special handlesHandle for 602 winch 21 000 250 420
Reefing gear handle 21 323 – 160
Winch handle pocketFabric winch handle pocket 21 050 300 70
Winch handle holderWinch handle holder 21 055 52mm Ø base
A range of light duty winch handles and accessories,manufactured from quality modern materials.All designed to fit international star socketsand standard deck filler caps.
Extruded aluminium handlesLight duty, inexpensive handles in two lengths andeither plain or locking. Both styles have easy-griproller handle and ‘Spectro’ grey anodised finish.
Important note:These handles should not be used on large, two-speedwinches as they are not designed for high loads in ananti-clockwise direction. SWL 40kg.
Floating handlesFeaturing a moulded body with an integralmoulded handle shaft. The bright red handleroller is mounted on ball bearing for friction-freeoperation. Locking mechanism is with a positive,easy action thumb switch. Handle floats in saltand fresh water.
Important note:Floating winch handles have a SWL of 40kg andare intended for lightweight use only.
Chrome handleFor use with the now-discontinued ‘602’bottom handle winch.
Winchhandle pocketManufactured fromhard-wearing syntheticfabric which will notdegrade like mouldedplastic versions.
Winchhandle holder
Utilises the star socketsystem to provide a
unique way of stowingwinch handles.
Mounts ontobulkheads or
locker lids.Requires 3 x 4mm
fastenings.
Base Ø 52mm
21 050
21 055
21 000
Reefinggear handleFor use with the now-discontinued ‘323’roller reefing gear.
21 323
21 001
21 011
21 002
21 022
21 034
21 033
41www.bartonmarine.com
winches &
winch ha
ndles
Barton composite winches & the Barton ‘Wincher’
Part Base Ø Drum Ø WeightNo. mm mm g
Sheet winchesSingle speed 8:1 21 200 101.6 66.7 835
Twin speed 16:1 21 201 114.3 66.7 1264
Twin speed 23:1 21 202 114.3 66.7 1600
Spares kitsSingle speed 8:1 21 210
Twin speed 16:1 21 211
Twin speed 23:1 21 212
Snubbing winchesSnubbing winch 21 100 64 37 175
Snubbing winch 21 101 75 50 230
Barton composite winchesA versatile alternative to conventional aluminium winches, the Bartonrange of composite winches offer significant cost and weight savingsand are truly low maintenance.
Virtually self-lubricating, friction-free and corrosion resistant, theingenious use of advanced materials ensure consistent performanceand reliability.
• Three models available – a single-speed 8:1 and twotwin-speeds; 16:1 and 23:1
• Suitable as primaries for yachts up to 10m (30ft) or asspinnaker /halyard winches on larger craft
• Red, blue and green coloured top rings are included,giving you the ability to colour-code winches to controllines, port or starboard, or just to match the colourscheme of your boat
• Comprehensive spares kits available.
Part Max drum Ø Max rope Ø WeightNo. mm mm g
Barton ‘Winchers’Wincher small (pair) 21 641 64-70 8-10 202
Wincher medium (pair) 21 642 70-80 10-14 223
Wincher large (pair) 21 643 80-90 12-14 278
Wincher ex large (pair) 21 644 90-100 12-16 387
21 202
Snubber winchesNeat, lightweight units which are ideal for use onlarger dinghies and dayboats. Manufacturedfrom glass fibre reinforced nylonwith anodised aluminium ribs.
21 201
21 200
The Barton ‘Wincher’A specially designed rubber moulding which fits over the topof standard winches, converting them to self-tailing.
This simple operation works when the line is sheeted under load,which means the coils climb up the winch drum and then becomegripped by the underside of the Wincher’s rubber body.
Cleating is achieved by lockingthe sheet into the Wincher’s
ribbed central groove.
Barton ‘Winchers’ are easyto fit and available in foursizes to suit a wide rangeof popular winches.
Full fitting instructionsare included.
21 101
21 100
Self-TailingFor self-tailing, the entirewinch must be stacked
with line.
Cleating...To cleat, lock sheet into
ribbed groove.
21 643
www.bartonmarine.com
sail
hand
ling
42
Lazy jack kits
PartNo.
Lightweight lazy jack kitsFor yachts up to 9m (30ft) 41 140
Cascade system for yachts up to 10.5m (35ft) 41 143
Lazy jack kitsFor yachts up to 9m (30ft) 41 150
For yachts up to 12m (40ft) 41 151
For yachts over 12m (40ft) 41 152
Cascade system for larger yachts 41 153
Lazy jack kitsAllow mainsails to be reefed or dropped with ease, byretaining the sail between lines running from the mast(near the hounds) to the boom. These lines can be slackenedwhilst sailing to avoid restricting sail shape.
Ideal for use with fully battened or conventional mainsails,these complete kits contain stainless steel, plastic-coatedwires with blocks and fixing eyes attached. High qualitybraided line, all fixings and comprehensive fittinginstructions are also included.
A unique feature of Barton lazy jack kits is the softplastic block covers which prevent sail chafe andenhance appearance.
Lightweight lazy jack kitsThese all-rope kits still feature our unique block covers butare intended for smaller yachts or lightweight use.
Not recommended for large yachts or fully battened mains.We also recommend that the use of a topping lift is retained.
Cascade lazy jack kitsAvailable in standard and lightweight format. For use withlonger boom lengths or where more sail control is required.
Standard lazy jack kitsNo modifications to sail, mast orboom required.
Blocks, cleats, mounting eyes andfixings included in the kit.
Chafe coversprevent blocksfrom wearing sail Nylon-coated
stainless wire
High qualitybraided line
High qualitycheek block
Adjustmentcleat
Stainless steelpad eyes
Cascade lazy jack kitsBlocks, cleats, mounting eyes and
fixings included in the kit.
60 750
PartNo.
Mast stepMast step (stainless steel) 60 750
Important note:mast stepsMast steps shouldalways be used inconjunction with abosun’s chair.
Always have a crewmember at hand tocontrol the halyard.
Do not go aloft barefootand always put safetyfirst when going aloft.
Mast stepLow profile, lightweight hinged mast step, manufacturedfrom bright polished stainless. Featuring a secure and positive
hinge action to ensure that the product is rattle-free. The foot hold area has a toothed non-slipsurface and the profile turns up at the out-
board end for a firm and secure foothold.
Secure using 4 x 5mm pop rivets and fitat 500mm spacing (as shown in theadjacent diagram).
41 150
41 140
41 143
43control the power
sail ha
ndling
Reefing kits & hooks
41 496
Single line reefing kitA boxed complete single-line reefing kit thatallows reefing lines to be led aft to the safetyof the cockpit.
This system makes reefing your mainsail a quickand easy operation – just lower the main to apredetermined mark on the halyard, tensionthe reefing line and re-trim the sail.
Supplied as a complete set with all the partsand fixings required, together with full fittinginstructions. All you need to provide is a lineand a cleat or stopper.
Slab reefing kitsSupplied with sliding blocks which are held in placewith spring-loaded plungers. Manufactured fromstainless steel and ‘Spectro’ anodised aluminium.Available in two sizes and complete with sufficientlength of ‘T’ track and end stops.
Specifications
41 483 – supplied with 60cm of 25mmanodised ‘T’ track
41 496 – supplied with 100cm of 32mm
anodised ‘T’ track
PartNo.
Single line reefing kitFor yachts up to 9m (30ft) 41 130
Slab reefing kitsFor yachts up to 8.5m (28ft) 41 483
Spare slider for above 41 484
For yachts up to 12m (39ft) 41 496
Spare slider for above 41 497
Plain Ball-bearing Sheave Ø Max line Ø Max tube Øsheave sheave mm mm mm
Stanchion lead blocks
Single stanchion – size 2 02 190 12 190 35 8 25
Double stanchion – size 2 02 290 12 290 30 10 25
Single stanchion – size 3 03 190 13 190 45 10 25
Single stanchion – size 4 04 190 14 190 58 12 25
Stanchion bullseye
Stanchion bullseye 60 142 bullseye internal diameter 17mm
PartNo.
Reefing hooksBoom fitting (pair) 41 517
Gooseneck or stemhead fitting 41 518
Reefing/gooseneck hooksManufactured in stainless steel, both thesetypes of hook are used in conjunction with slabreefing kits for securing the mainsail tack.
Type 41 517 is supplied in pairs and is intendedfor mounting either side of the boom atgooseneck level.
Type 41 518 can be mounted above thegooseneck or can be used at the stemheadto accept a jib tack.
Stanchion lead blocksMainly used for leading headsail furling linesaft, Barton stanchion blocks are available inthree sizes to suit most applications.
Double blocks are designed for use with endlessline systems and can easily be taken apart toaccept pre-spliced lines.
A larger size 4 block should be used for finaltake-off, especially if the furling line is to belead to a winch.
All stanchion blocks are available with eitherplain or ball-bearing sheave.
41 130
41 483 41 517
41 518
02 190
03 190
04 190
60 142
02 290
control the power
44
Special cleats
51 250
Clamp-on cleatsExclusive to Barton, this unique design features an opening basewhich fits over existing ‘T’ track. The clamp design then screwsfirmly into place, allowing this cleat to be fixed in any positionon your track in seconds.
• Leaves deck clear when not in use• Fitted, adjusted or removed in seconds• Position exactly where required along existing ‘T’ track• Available for 25mm and 32mm ‘T’ track.
51 320
Part Cleat Length T track WeightNo. material mm width mm g
Clamp-on cleatsClamp-on cleat 51 250 Ali 175 25 260
Clamp-on cleat 51 320 Ali 205 32 389
Sliding cleats165mm sliding cleat 51 253 Nylon 165 25 134
200mm sliding cleat 51 254 Nylon 200 25 178
175mm sliding cleat 51 322 Ali 175 32 328
205mm sliding cleat 51 323 Ali 205 32 402
Stanchion cleatStanchion cleat 52 100 Nylon 111 – 90
Shroud cleatsShroud cleat 52 110 Nylon 100 – 26
Shroud cleat with eye 52 111 Nylon 100 – 26
Stanchion bullseyeStanchion bullseye 60 142 Nylon bullseye int. Ø 17mm
Line TamerLine tamer grey (pair) 52 000 Nylon 73 – 12
Line Tamer white (pair) 52 001 Nylon 73 – 12
51 253
51 254
51 323
51 322
Fits standardsection ‘T’ trackAll stainless construction
with cast aluminium cleat
Heavy-dutyhinge allowseasy positioningover track
Easy to use,clamp-on action
Sliding cleatsA cost-effective solution to fitting a mid-ship spring cleat whereaccess under the side deck is limited - simply remove a genoa trackend stop, slide on the cleat and lock it in the desired position.When not in use, slide the cleat to one end of the track, or leaveoff one track end permanently to enable easy removal of cleat.Alternatively, fit a short length of track in the desired position sothat cleats can be fitted when required and removed when not inuse – reducing deck clutter and rope snags.
• Available for 25mm and 32mm ‘T’ track, eachin two sizes
• 25mm cleats have an extruded aluminium basewith a moulded nylon cleat and screw lock
• 32mm cleats have an extruded aluminium base,cast aluminium cleat and plunger type lock.
The Barton ‘Line Tamer’A new line storage device designed to keep cockpits free fromun-used lines and halyards. A smooth profile ensures no snaggingas crew members brush past. Sold in pairs in grey or white.
Full fitting instructions are included. Suitable for rope coils ofup to 20cm diameter.
Important note:clamp-on cleatClamp-on cleats will only work correctlyand safely with ‘T’ section track.
Stanchion cleatDesigned to fit stanchions orpushpit/pullpit tubes – fits inseconds and features softnylon jaws that will notdamage the tube.
52 111
60 142
52 100
52 110
Shroud cleatsTwo handy cleats that simply clamponto shroud wire (max 8mm Ø)without causing damage.
52 110 is a plain cleat for flaghalyards etc.
52 111 features a wide eye openingfor stowage of halyard shackles.
clea
ting
52 000
45www.bartonmarine.com
cleating
Fairleads, cleats and thimbles
Part Length Width Fastenings Ø Weight Max Rope ØNo. mm mm mm g mm
Fairleads (pairs)Nylon fairleads (pair) 60 160 115 25 5 72 10
Nylon fairleads (pair) 60 161 155 34 6 140 12
Part Length Fastenings Ø Weight Bore (int Ø)No. mm mm g mm
Tubular CleatsTube cleat 52 120 55 4 4 8
Tube cleat 52 121 80 6 13 13
Part Max rope Ø Fastening centres Fastenings Ø Holding powerNo. mm mm mm kg
Aluminium cam cleatsAluminium cam cleat midi 70 400 10 37 5 180
Ali cam cleat midi + f/lead 70 401 10 37 5 180
Aluminium cam cleat maxi 70 500 14 50 5 230
Ali cam cleat maxi + f/lead 70 501 14 50 5 230
Budget cam cleatsBudget cam cleat mini 70 600 10 30 4 –
Budget cam cleat midi 70 601 6-12 40 5 –
Budget cam cleat maxi 70 602 10-14 50 5 –
Part Length Fastenings Ø WeightNo. mm mm g
Open nylon cleatsOpen nylon cleat 52 140 75 3 6
Open nylon cleat 52 141 100 4 12
Open nylon cleat 52 142 130 4 26
Open nylon cleat 52 143 170 5 49
Open nylon cleat 52 144 210 6 84
Open nylon cleat 52 145 245 8 157
Part Length Width Max rope ØNo. mm mm mm
Nylon thimblesNylon thimble 60 404 35 26 6
Nylon thimble 60 405 38 28 8
Nylon thimble 60 406 48 36 10
Nylon thimble 60 407 53 40 12
Nylon fairleadsMoulded from tough black nylon with smooth,snag-free design. Supplied in handed pairs.
Tubular cleatsAvailable in 2 sizes, these handy cleats havemany uses where light loads are expected.
Aluminium cam cleatsAvailable in two sizes, accepting lines up to14mm. A well-proven design; extremely strongand rugged, with a hard anodised satin finish.Bases on the fairlead models are fromstainless steel.
Budget cam cleatsOf the same design as our ‘K’ cam range (page48), this low cost range features camsmoulded from light grey glass-reinforced nylon.
All ‘K’ cam accessories shown on page 48are compatible.
Open (horn) cleatsA wide range of open horn cleats mouldedfrom high strength black nylon.
ThimblesA range of thimbles mouldedin white nylon.
52 14552 144
52 143
52 142
52 141
52 140
52 120
52 121
60 161
60 160
70 400
70 401
70 500
70 501
60 404 60 40760 405 60 406
70 602 70 601 70 600
www.bartonmarine.com
46
Dinghy & dayboat fittingsd
ing
hy s
aili
ngFurling gearSingle line operation for dinghies, dayboatsand light cruising yachts – two drum sizeswork with a common top head swivel. All havestainless steel ball races for smooth operation.
Drums are moulded from glass fibre reinforcednylon with stainless steel swivel and ballbearing assemblies.
Top head swivel is from machine-turned solidaluminium with stainless steel ball bearing.
Mainsheet swivelswith cam cleatSwivel block accepts lines up to 10mm Øand features a fully articulated block withanti-tumble spring and ‘K’ cam cleat.
Swivel bullseye accepts lines up to12mm Ø and features a stainless steelinsert and ‘K’ cam cleat.
Part Drum Ø Sail area Break load SWL WeightNo. mm sq ft kg kg g
Furling gearsFurling drum 42 334 76 60 1108 554 218Furling drum 42 335 95 100 1108 554 281Top swivel 42 336 25 100 1108 554 55
Part Max line Ø Base Ø Fastenings Ø WeightNo. mm mm mm g
Mainsheet swivels with camSwivel block with cam 42 600 10 58 5 250Bullseye swivel with cam 42 601 12 58 5 217
Part Length Fastenings Ø Max line Ø WeightNo. mm mm mm g
FairleadsFairlead + cam (handed pair) 42 102 90 5 12 732Sheet fairlead 42 200 65 5 14 16Spinnaker fairlead 42 201 75 4 8 8
Part Bore Ø Cutting Ø Fastenings Ø WeightNo. mm mm mm g
Drain bungs & socketsBung & socket – black 42 356 15 22 4 11Bung only – black 42 357 15 – – 7Bung & socket – white 42 358 15 22 4 11Bung only – white 42 359 15 – – 7
Part Strap width Pintle Ø Fastenings Ø WeightNo. mm mm mm g
Rudder & transom fittingsRudder pintle 42 419 19 9.5 5 91Rudder pintle 42 422 22 9.5 5 95Rudder pintle 42 435 35 9.5 5 104Rudder pintle 42 450 50 9.5 5 114Rudder gudgeon 42 519 19 – 5 81Rudder gudgeon 42 522 22 – 5 82Rudder gudgeon 42 535 35 – 5 91Rudder gudgeon 42 550 50 – 5 101Transom pintle 42 400 – 9.5 5 70Transom gudgeon 42 500 – – 5 30
Rigging adjusterRigging adjuster 42 700
42 334 42 335
42 357 42 356
42 400
42 500
42 519
42 700
42 419
42 359 42 358
42 600
42 336
42 201
42 601
42 102
42 200
FairleadsFairleads with plunger andcam cleat for use on 20mm ‘T’ track(see page 33 for complete range of20mm ‘T’ track fittings). Sold in handedpairs. Includes budget cam cleat fixedon stainless steel plate.
Sheet fairlead – a moulded plasticfixed fairlead.
Spinnaker fairlead – a mouldedplastic sheet fairlead with snap in/outhook design.
Drain bungs & socketsThis screw-type drain bung andsockets is still among the best available.Supplied with rubber ‘O’ ring fora watertight seal. Available inblack or white.
Rudder & transom fittingsManufactured from stainless steel with tough nylonsurrounds. A wide range of rudder fitting widthsare available.
Rigging adjusterManufactured from 16mm stainless steel plate– allows for total 50mm adjustment in 10mm steps.Clevis pin 5mm Ø. Overall length 91mm.
47control the power
tiller extensionsTiller extensions
43 103
PartNo.
Ali extensions – plain buttonTiller extension – ali – plain button 600mm 43 101
Tiller extension – ali – plain button 700mm 43 102
Tiller extension – ali – plain button 800mm 43 103
Tiller extension – ali – plain button 900mm 43 104
Tiller extension – ali – plain button 1050mm 43 105
Tiller extension – ali – plain button 1200mm 43 106
Ali extensions – golf gripTiller extension – ali – golf grip 600mm 43 201
Tiller extension – ali – golf grip 700mm 43 202
Tiller extension – ali – golf grip 800mm 43 203
Tiller extension – ali – golf grip 900mm 43 204
Tiller extension – ali – golf grip 1050mm 43 205
Tiller extension – ali – golf grip 1200mm 43 206
Plastic extensions – plain buttonTiller extension – plastic – plain button 600mm 43 001
Tiller extension – plastic – plain button 700mm 43 002
Tiller extension – plastic – plain button 800mm 43 003
Tiller extension – plastic – plain button 900mm 43 004
Plastic extensions – golf gripTiller extension – plastic – golf grip 600mm 43 011
Tiller extension – plastic – golf grip 700mm 43 012
Tiller extension – plastic – golf grip 800mm 43 013
Tiller extension – plastic – golf grip 900mm 43 014
Part Length Tube int Ø WeightNo. mm mm g
Flexible tiller jointsFlexible tiller joint 43 600 58 13 20
Light flexible tiller joint 43 601 58 13 20
43 102
43 101
43 10443 204
43 203
43 202
43 201
43 600
Barton tiller extensionsManufactured from 15mm diameter aluminium orextruded PVC tube and available in a wide varietyof lengths.
All Barton tiller extensions feature our flexible joint whichcan easily be removed from the tiller when required.
• Aluminium extensions in ‘Spectro’ greyanodised material.
• Plastic extensions in heavy-duty, UV-stabilisedgrey PVC tube, manufactured especiallyfor Barton.
• Both types available with either golf gripor plain button end options.
Flexible tiller joints
Manufactured from high-tech polymers to withstandcountless tiller flexings. The joint can easily be removedfrom the tiller assembly by popping off the snap-on cover.
Two versions are available – the smaller diametergiving a softer action for shorter extensions.
control the power
48
‘K’ cam cleatsca
m c
lea
ts
Specifications ‘K’ cam mini ‘K’ cam midi ‘K’ cam maxi
Max line Ø 10mm 6-12mm 10-14mm
Fastenings Ø 4mm 5mm 5mm
Fastening 30mm 40mm 50mmcentres
Holding power 190kg 230kg 260kg
Weight 17g 34g 50g
‘K’ cam ‘K’ cam ‘K’ cammini midi maxi
‘K’ cam cleat only‘K’ cam cleat only 70 100 70 200 70 300
‘K’ cam cleat with wire front fairlead
‘K’ cam cleat with wire front fairlead 70 101 70 201 70 301
Wire front fairlead onlyWire front fairlead, stainless steel 70 104 70 204 70 304
Pillar fairlead onlyPillar fairlead, grey 70 105 70 205 70 305
Pillar fairlead, green 70 115 70 215 70 315
Pillar fairlead, red 70 125 70 225 70 325
Pillar fairlead, yellow 70 135 70 235 70 335
Top fairlead onlyTop fairlead, grey 70 106 70 206 70 306
Top fairlead, green 70 116 70 216 70 316
Top fairlead, red 70 126 70 226 70 326
Top fairlead, yellow 70 136 70 236 70 336
Wedge mountWedge mount 70 140 70 240 70 340
Cam top capsPack cam top caps, 2 x red, green, yellow 70 141 70 241 70 341
70 300
70 200
70 100
70 30170 304
70 104
70 340
70 204
70 140
70 240
‘K’ cam cleatsManufactured from a composite Kevlar/Zytal material and available in 3 sizes toaccept lines up to 14mm in diameter. This advanced material offers performanceadvantages over carbon fibre and conventional glass-reinforced resins; ‘K’ camsare very strong, lightweight and have excellent wear-resistance. A progressive toothdesign ensures maximum holding power on all types of line, whilst maintainingminimum wear to both cam and line.
‘K’ Cam bases feature a stainless steel wear bar for prolonged life.
Cams utilise stainless steel leaf springs which give a smooth but positive action.They are also stronger and have a longer life than conventional wire springs.
‘K’ cam cleats are supplied as cleat only plus separate accessories in grey, green, redor yellow where appropriate, to allow colour co-ordination for port, starboard etc.
Wire front fairleadsFrom stainless steel.
Pillar fairleadsThese add-ons enable the cam cleat to be engaged from a variety of angles.Cams can be fitted either way around to achieve a lead from in front or behind.Stainless steel pillars add strength and wear resistance.
Top fairleadsIncorporating stainless steel reinforcing for added strength and wear resistance.
Wedge mountsAngled wedge mounts to suit the 3 sizes of ‘K’ cam cleat.
Cam top capsSupplied in packs containing 2 each of red, green and yellow cam top caps.
49www.bartonmarine.com
ma
st supp
ort‘K’ cam cleats Dinghy mast support
PartNo.
Dinghy mast supportDinghy mast support 42 300
70 135
70 215
70 205
70 325
70 206 70 226 70 21670 236
70 241
Dinghy mast supportDesigned to support the aft end of a dinghy mast when towing.Simply fits onto standard transom fittings and is instantly ready foruse. Fully adjustable for different transom heights and features aremovable pintle to accommodate different transom layouts.
The yolk features a soft neoprene pad to protect the mast, shroudsand lines. Generous eyelets in the yolk allow for a securing line to beeasily attached. A trailer board can be fitted to the cross plate with2 x 6mm screws (not supplied).
• Easy to fit• No fastenings required• Fully and easily adjustable• Increases towing safety• Prevents damage to mast and deck.
Neat mouldedtop cap assembly
Cams mouldedfrom Kevlar/Zytalcomposite – ensureshigh strength andwear resistance
Mouldedbase platepreventsharmfulbuild-upof dirtand gritin movingparts
Stainlesssteel barpreventsbaseburn-out
Progressivetoothdesign formaximumholdingpower andease ofentryand release
Self-lubricating,low frictionslotted cambearing
Base mouldedfrom long-fibrereinforcedengineeringpolymer
Stainless steelleaf springsensure alightweight,smooth camaction
Adjustablemax/minheight
Adjustableheight
Removablepintle
Adjustbottomfitting andheight ofyolk to suittransomfittings andtransomheight, thentighten thelocking nut.
Remove bottompintle if transomhas 2 gudgeons.
Attach trailer lightingboard with 2 x 6mmfastenings
42 300
www.bartonmarine.com
50
Inspection coversin
spec
tion
cove
rs
Part No. Part No. Part No. Aperture Ø Cutting Ø Overall Ø Fastenings Ø WeightWhite Black Clear mm mm mm mm g
Screw inspection covers – round
Screw inspection cover – round 40 040 40 041 40 042 103 114 145 4 84
Screw inspection cover – round 40 050 40 051 40 052 130 139 170 4 107
Screw inspection cover – round 40 060 40 061 40 062 155 165 215 4 172
Screw inspection cover – round 40 080 40 081 40 082 200 215 260 4 400
Push-fit inspection covers – round
Push-fit inspection cover – round 40 220 40 221 – 195 205 240 5 326
Push-fit inspection cover – round + ‘T’ lock 40 240 40 241 – 185 217 268 5 508
Push-fit inspection cover – round + ‘T’ lock 40 250 40 251 – 257 267 317 5 739
Hinged inspection covers – rectangular
Hinged insp cover – rectangular + ‘T’ lock 40 320 – – 178 x 279 208 x 310 260 x 362 5 900
Hinged insp cover – rectangular + ‘T’ lock 40 340 – – 216 x 289 273 x 329 318 x 394 5 1134
40 051
Inspection coversBarton offer a wide range of inspection covers in screw, push-fit,and locking versions. Round and rectangular covers are available.
Screw inspection covers
Manufactured from high-impact polycarbonate, these coversfeature a course, easy-start thread and a built-in ‘O’ ring seal.
Available in four diameters and in white, back and clear window.
Push-fit inspection covers
A range of larger-sized covers with a firm push-fitaction which seals onto a soft rubber ‘O’ ring.The two largest models are fitted with a lock-downsystem which operates by lifting the ‘T’ bar andturning it through 90°. UV and acetone-resistant.
Hinged rectangular inspection covers
Hinged on the top edge, these covers featurethe ‘T’ lock system and a soft rubber seal.Available in white only. UV and acetone-resistant.
40 042
40 04140 050
40 062
40 240
40 320
40 221
40 08040 061
51control the power
inflata
ble rep
air
ClamSeal™
Dame award category winnerWinner of a National MarineManufacturer’s Association ProductInnovation Award
Pull theplates of theClamSeal™together,across thesplit, usingthe lanyard
With the 2plates pulledtogether,simply hand-tighten thenut for aClam-tightseal!
Reinflate andyou’re safeto continueon yourway!
The award-winning, patentedClamSeal™ – repairs inflatablesfast – even when wet
The ClamSeal™ can instantly repair splits and tears up to 90mm (31/2”) in lengthwithout the use of any hand tools, or adhesive.
ClamSeal™ is a patented glue-less repair system that instantly repairs small tears orsplits in inflatables above or below the waterline – regardless of the fact that thematerial may be wet.
The system works by using two half ‘shells’ that screw together tightly, using theinflatable material itself as a water and air-tight seal. It is quick and easy to fit andeffects an immediate repair which can keep you afloat until a more permanentrepair can be made.
• Quick and easy to fit
• Requires no adhesive or tape
• Can be used above or below the waterline
• Can be used on wet materials
• Provides an instant repair
• Re-useable again and again.
PartNo.
ClamSeal™
Barton ClamSeal™ 60 001
ClamSeal™ is suitable for use on:
• RIBs
• Dinghies
• Liferafts
• Buoyancy bags
• Virtually any inflatable product.
Open theClamSeal™and insertthe baseplateinto thesplit.
1
The ClamSeal™ can be carried as part of your emergency equipment on board. Itcan be used at sea, on shore; even underwater as no adhesive or tape is involved.The clever mechanics of the ClamSeal™ design mean this simple product cankeep you safely afloat.
The ClamSeal™ has now become a permanent part of the safety kit on many RIBsaround the world and is continuing to amaze those who have used them – aneffective, low cost solution to an otherwise complicated problem.
2
3 4
Pat pending GB0329522.7
60 001
60 001
control the power
52
Fuel Whistlefu
el w
hist
le
fuel tank
The Barton Fuel WhistleA simple device to prevent accidentalspillages whilst refuelling
This unique patented product has been designed to give anaudible warning to prevent fuel spills during the refuelling ofyour boat. This helps prevent marine pollution and ensuresthat your topsides and deck are kept free from spills.
Tens of thousands of boats are refuelled every day and each timeup to half a gallon of fuel is potentially spilled into our waterways.For the most part this environmental hazard goes unreportedand unchecked.
Disturbed by an oily sheen on the surface of the water,some boat-owners may spray a liquid soap on the slickto break up the mess. This is actually even more harmfulto the environment, as the soap carries the oil to thesediment at the bottom where it builds up year after year.This sediment threatens all sea bed-dwelling life.
Until now, controlling these fuel spills has been difficult.Barton Marine has produced a simple and inexpensive fuelspill prevention device to warn that the fuel tank isapproaching full without spilling a single drop of fuel.
With the ‘Fuel Whistle’, there will be no more guess work, nowaste, no pollution. Every boat-owner can be a partner inprotecting our precious resources.
Installing the Fuel Whistle
• The 16mm (5/8") fuel vent line iscut approx 300mm (12”) fromthe fuel tank
• The ‘Fuel Whistle’ is inserted withthe arrows facing the hull vent.
• The Fuel Whistle is thensecured with 2 x hose clamps(not supplied).
• If required, the device can be heldin place with 2 stainless steelscrews inserted into the mouldedmounting ears.
• The ‘Fuel Whistle’ should beoriented within 45° of the verticalto allow for proper drainage.
Specifications
Overall length 95mm
Installed length 50mm
Width (including lugs) 50mm
How it works...
While the tank is being filled a‘whistling’ sound is producedby the ‘Fuel Whistle’.
The sound is loud enough tobe heard from any point onthe boat. It will be audible ina strong breeze or with anynormal surrounding sounds.
As the tank approaches full,the sound turns to a ‘warble’and when completely full itstops altogether – giving anearly warning to stop fillingBEFORE a fuel spill occurs.
• Eco-friendly
• Simple to fit
• Protects the environment and your deck
• Suitable for sail and power boats
• Fitting instructions included
• Cost-effective.
PartNo.
Barton fuel whistleFuel whistle 60 010
60 010
BullseyesA range of four bullseyes for through-deck or on-deck screw mounting. All featurea strong, moulded plastic eye, reinforced with a stainless steel bar. Two models alsofeature a stainless steel eye insert to limit wear to the line. All accept lines up to16mm Ø.
Pad eyesA wide range of attachment eyes/fairleads manufactured from stainless steel.Featuring a solid stainless steel bar welded for extra security.
Folding pad eye – stainless steel pad eye with anti-vibration rubber pad.Folds flat to deck when not in use.
Double folding pad eye – with anti-vibration rubber pads and two fixingeyes which fold flat when not in use.
Deck eyes (stainless steel)Two stainless steel deck eyes with generous eye capacity.
Fairlead eyesMoulded from glass fibre reinforced nylon with stainless steel reinforcing.Available in 3 sizes and in a choice of grey, green, red or yellow.
Part of our ‘K’ cam range - see pages 48-49 for further details.
53www.bartonmarine.com
sailing
hard
wa
reBullseyes, pad eyes, deck eyes
Part Max line Ø D L1 L2No. Insert? sq ft mm mm mm
BullseyesThrough-deck 60 420 ✔ 16 6 57 18
Through-deck 60 421 ✔ 16 6 77 35
Through-deck 60 422 ✘ 16 6 105 60
Screw-to-deck 60 423 ✘ 16 6 40 –
Part Dia Ø Height Hole centre Width Fastenings ØNo. ‘A’ ‘B’ mm ‘C’ mm ‘D’ mm mm
Pad eyesPad eye – fixed 60 305 4 16 30 40 5
Pad eye – fixed 60 306 6 24 44 60 5
Pad eye – fixed 60 307 8 28 55 80 6
Pad eye – fixed 60 308 10 35 60 95 8
Pad eye – folding 60 309 6 42 36 54 6
Pad eye – dble folding 60 304 6 42 – – 6
Part Height Width Fastenings ØNo. ‘A’ mm ‘B’ mm mm
Deck eyes/fairlead eyesDeck eye – S/S 60 410 14 14 5
Deck eye – S/S 60 411 18 16 6
Deck eye – plastic, grey 70 106 9 15 4
Deck eye – plastic, green 70 116 9 15 4
Deck eye – plastic, red 70 126 9 15 4
Deck eye – plastic, yell 70 136 9 15 4
Deck eye – plastic, grey 70 206 12 20 5
Deck eye – plastic, green 70 216 12 20 5
Deck eye – plastic, red 70 226 12 20 5
Deck eye – plastic, yell 70 236 12 20 5
Deck eye – plastic, grey 70 306 15 25 5
Deck eye – plastic, green 70 316 15 25 5
Deck eye – plastic, red 70 326 15 25 5
Deck eye – plastic, yell 70 336 15 25 5
60 422 60 421
60 423
60 420
60 305
60 30760 306
60 308
60 309 60 304
70 23670 21670 22670 206
60 411
60 410
L1
www.bartonmarine.com
54
Clevis pins, split pins, springs and sheavessh
eave
s
PartNo.
Split ringsSplit rings – 10mm Ø - pack of 10 60 190
Split rings – 14mm Ø - pack of 10 60 191
Part Dia Ø Width BoreNo. ‘D’ mm ‘W’ mm mm
Sheaves – plain bearingPlain bearing sheave 64 801 30 11 8
Plain bearing sheave 64 802 32 14 8
Plain bearing sheave 64 803 32 17 11
Plain bearing sheave 64 804 35 12 8
Plain bearing sheave 64 805 35 18 13
Plain bearing sheave 64 806 38 17 13
Plain bearing sheave 64 807 44 18 13
Plain bearing sheave 64 808 44 20 13
Plain bearing sheave 64 809 45 11 8
Plain bearing sheave 64 810 45 14 8
Plain bearing sheave 64 811 48 20 13
Plain bearing sheave 64 812 57 14 8
Plain bearing sheave 64 813 58 17 11
Plain bearing sheave 64 814 64 18 13
Plain bearing sheave 64 815 70 18 13
Plain bearing sheave 64 816 70 20 13
Sheaves – ball bearingBall bearing sheave 64 901 30 12 4
Ball bearing sheave 64 902 30 14 4
Ball bearing sheave 64 903 32 17 6
Ball bearing sheave 64 904 35 12 4
Ball bearing sheave 64 906 38 17 6
Ball bearing sheave 64 907 44 17 6
Ball bearing sheave 64 908 44 20 6
Ball bearing sheave 64 909 45 12 4
Ball bearing sheave 64 910 45 14 4
Ball bearing sheave 64 912 57 14 5
Ball bearing sheave 64 913 58 17 6
Ball bearing sheave 64 914 64 18 6
Ball bearing sheave 64 915 70 18 6
Ball bearing sheave 64 916 70 20 6
Part Diameter Ø LengthNo. ‘D’ mm ‘L’ mm
Clevis pinsClevis pins – pack of 2 60 203 5 15
Clevis pins – pack of 2 60 204 5 18
Clevis pins – pack of 2 60 207 5 24
Clevis pins – pack of 2 60 208 5 33
Clevis pins – pack of 2 60 209 5 39
Clevis pins – pack of 2 60 210 6 10
Clevis pins – pack of 2 60 212 6 23
Part Diameter Ø HeightNo. ‘D’ mm ‘H’ mm
Stand-up springsSpring – S/S 60 120 20 35
Spring – S/S 60 121 30 30
Spring – plastic 60 122 40 50
Spring – plastic 60 123 48 55
Clevis pinsA comprehensive selection of clevis pins manufactured from 316 stainlesssteel – as used throughout the Barton range of blocks.
Supplied in packs of two.
Stand-up springsIdeal for mounting blocks on decks to prevent tumbling or causing ropesnags and deck damage. Either in stainless steel or soft plastic.
Available in two sizes.
Split ringsEasy-fit stainless steel split rings for use with our clevis pins.
Supplied in two sizes and in packs of 10.
SheavesA comprehensive range of plain and ball bearing sheaves as used throughoutthe complete Barton block range. Moulded from acetal resin, our unique,super-low friction ball race system features delrin balls running on a largediameter centre boss, which ensures an extremely low friction performance.
64 901
64 801
60 210
60 20960 208
60 203
60 207
60 204
60 123
60 120
60 121
60 122
60 191
60 190
55control the power
shackles
Shackles and ‘S’ hooks
Part Pin Ø Length WidthNo. mm ‘L’ mm ‘W’ mm
Screw pin shackles (strip)Strip shackle 60 310 5 27 10
Strip shackle 60 311 6 38 13
Strip shackle 60 312 8 50 16
Screw pin shackles (bar)Bar shackle 60 320 6 38 13
Bar shackle 60 321 6 44 20
Bar shackle 60 322 8 49 16
Bar shackle 60 323 8 55 20
Rigging linksRigging link 60 343 5 30 14
Rigging link 60 344 6 37 18
Rigging link 60 350 6 50 19
SwivelsSwivel 60 700 5 33 8
Swivel 60 701 5 33 9
Swivel 60 702 5 33 11
Swivel 60 703 6 45 14
ShacklesA range of screw pin strip and forged bar shackles instainless steel – as used throughout the Barton range.
Pin diameters up to 8mm available.
Rigging linksPressed stainless steel rigging links with clevis pinand ring in pin.
Sizes up to 6mm pin diameter.
SwivelsStainless steel swivels as used throughout our blocks.
Four sizes available.
‘S’ hooksA handy fitting with a multitude of uses. Manufacturedfrom stainless steel. Supplied as either a plain hook orwith spring latch fitted.
Part Bar Ø Length WidthNo. mm ‘L’ mm ‘W’ mm
‘S’ hooks‘S’ hook plain 60 708 6 73 19
‘S’ hook with latch 60 709 6 73 19
60 312
60 310
60 311
60 32360 322
60 32060 321
60 35060 343
60 344
60 703
60 70260 700 60 701
60 708 60 709
www.bartonmarine.com
56
Part number indexin
dex 01090 ............5
01091 ............501110 ............501111 ............501120 ............501121 ............501130 ............501131 ............501150 ............501151 ............501160 ............501170 ............501180 ............501190 ............501210 ............501211 ............501220 ............501221 ............501230 ............501231 ............501250 ............501280 ............501320 ............501321 ............501330 ............501331 ............5
02090 ............702091 ............702110 ............702111 ............702120 ............702121 ............702130 ............702131 ............702140 ............702141 ............702150 ............702151 ............702160 ............702161 ............702170 ............702171 ............702180 ............702190 ............702210 ............702211 ............702220 ............702221 ............702230 ............702231 ............702250 ............702280 ............702290 ............702320 ............702321 ............702330 ............702331 ............702410 ............702411 ............702420 ............702421 ............702430 ............702431 ............702440 ............702441 ............702531 ............702541 ............702571 ............702631 ............702641 ............702731 ............702740 ..........19
03090 ............903091 ............903110 ............903111 ............903120 ............903121 ............903130 ............903131 ............903140 ............903141 ............903150 ............903151 ............903160 ............903161 ............903170 ............903171 ............903180 ............903181 ............903190 ............903210 ............903211 ............903220 ............903221 ............903230 ............903231 ............903250 ............903320 ............903321 ............903330 ............903331 ............903410 ............903411 ............903420 ............903421 ............903430 ............903431 ............903440 ............903441 ............903480 ............903481 ............903511 ............903531 ............903541 ............903571 ............903631 ............903641 ............903681 ............903731 ............9
04090 ..........1104091 ..........1104110 ..........1104111 ..........1104120 ..........1104121 ..........1104130 ..........1104131 ..........1104140 ..........1104141 ..........1104150 ..........1104151 ..........1104160 ..........1104170 ..........1104171 ..........1104180 ..........1104181 ..........1104190 ..........1104210 ..........1104211 ..........1104220 ..........1104221 ..........1104230 ..........1104231 ..........1104250 ..........11
04320 ..........1104321 ..........1104330 ..........1104331 ..........1104410 ..........1104411 ..........1104420 ..........1104421 ..........1104430 ..........1104431 ..........1104440 ..........1104441 ..........1104480 ..........1104481 ..........1104531 ..........1104541 ..........1104571 ..........1104630 ..........1104631 ..........1104641 ..........1104681 ..........1104731 ..........1104930 ..........1104931 ..........11
05110 ..........1305111 ..........1305120 ..........1305121 ..........1305130 ..........1305131 ..........1305140 ..........1305141 ..........1305170 ..........1305171 ..........1305180 ..........1305181 ..........1305220 ..........1305221 ..........1305320 ..........1305321 ..........1305330 ..........1305331 ..........1305420 ..........1305421 ..........1305430 ..........1305431 ..........1305440 ..........1305441 ..........1305480 ..........1305481 ..........1305631 ..........1305641 ..........1305681 ..........1305930 ..........1305931 ..........13
06110 ..........1506111 ..........1506120 ..........1506121 ..........1506130 ..........1506131 ..........1506140 ..........1506141 ..........1506170 ..........1506171 ..........1506180 ..........1506181 ..........1506220 ..........1506221 ..........1506320 ..........1506321 ..........1506330 ..........1506331 ..........15
06420 ..........1506421 ..........1506430 ..........1506431 ..........1506440 ..........1506441 ..........1506480 ..........1506481 ..........1506631 ..........1506641 ..........1506681 ..........1506930 ..........1506931 ..........15
07110 ..........1707111 ..........1707120 ..........1707121 ..........1707130 ..........1707131 ..........1707140 ..........1707141 ..........1707170 ..........1707171 ..........1707180 ..........1707181 ..........1707220 ..........1707221 ..........1707320 ..........1707321 ..........1707330 ..........1707331 ..........1707420 ..........1707421 ..........1707430 ..........1707431 ..........1707440 ..........1707441 ..........1707480 ..........1707481 ..........1707631 ..........1707641 ..........1707681 ..........1707930 ..........1707931 ..........17
11090 ............511091 ............511110 ............511111 ............511120 ............511121 ............511130 ............511131 ............511150 ............511151 ............511160 ............511170 ............511180 ............511190 ............511210 ............511211 ............511220 ............511221 ............511230 ............511231 ............511250 ............511280 ............511320 ............511321 ............511330 ............511331 ............5
12090 ............712091 ............7
12110 ............712111 ............712120 ............712121 ............712130 ............712131 ............712140 ............712141 ............712150 ............712151 ............712160 ............712170 ............712171 ............712180 ............712190 ............712210 ............712211 ............712220 ............712221 ............712230 ............712231 ............712250 ............712280 ............712290 ............712320 ............712321 ............712330 ............712331 ............712410 ............712411 ............712420 ............712421 ............712430 ............712431 ............712440 ............712441 ............712531 ............712541 ............712571 ............712631 ............712641 ............712731 ............7
13090 ............913091 ............913110 ............913111 ............913120 ............913121 ............913130 ............913131 ............913140 ............913141 ............913150 ............913151 ............913160 ............913170 ............913171 ............913180 ............913181 ............913190 ............913210 ............913211 ............913220 ............913221 ............913230 ............913231 ............913250 ............913320 ............913321 ............913330 ............913331 ............913410 ............913411 ............913420 ............9
13421 ............913430 ............913431 ............913440 ............913441 ............913480 ............913481 ............913511 ............913531 ............913541 ............913571 ............913631 ............913641 ............913681 ............913731 ............9
14090 ..........1114091 ..........1114110 ..........1114111 ..........1114120 ..........1114121 ..........1114130 ..........1114131 ..........1114140 ..........1114141 ..........1114150 ..........1114151 ..........1114160 ..........1114170 ..........1114171 ..........1114180 ..........1114181 ..........1114190 ..........1114210 ..........1114211 ..........1114220 ..........1114221 ..........1114230 ..........1114231 ..........1114250 ..........1114320 ..........1114321 ..........1114330 ..........1114331 ..........1114410 ..........1114411 ..........1114420 ..........1114421 ..........1114430 ..........1114431 ..........1114440 ..........1114441 ..........1114480 ..........1114481 ..........1114531 ..........1114541 ..........1114571 ..........1114630 ..........1114631 ..........1114641 ..........1114681 ..........1114731 ..........1114930 ..........1114931 ..........11
15110 ..........1315111 ..........1315120 ..........1315121 ..........1315130 ..........1315131 ..........1315140 ..........1315141 ..........1315170 ..........13
15171 ..........1315180 ..........1315181 ..........1315220 ..........1315221 ..........1315320 ..........1315321 ..........1315330 ..........1315331 ..........1315420 ..........1315421 ..........1315430 ..........1315431 ..........1315440 ..........1315441 ..........1315480 ..........1315481 ..........1315631 ..........1315641 ..........1315681 ..........1315930 ..........1315931 ..........13
16110 ..........1516111 ..........1516120 ..........1516121 ..........1516130 ..........1516131 ..........1516140 ..........1516141 ..........1516170 ..........1516171 ..........1516180 ..........1516181 ..........1516220 ..........1516221 ..........1516320 ..........1516321 ..........1516330 ..........1516331 ..........1516420 ..........1516421 ..........1516430 ..........1516431 ..........1516440 ..........1516441 ..........1516480 ..........1516481 ..........1516631 ..........1516641 ..........1516681 ..........1516930 ..........1516931 ..........15
17110 ..........1717111 ..........1717120 ..........1717121 ..........1717130 ..........1717131 ..........1717140 ..........1717141 ..........1717170 ..........1717171 ..........1717180 ..........1717181 ..........1717220 ..........1717221 ..........1717320 ..........1717321 ..........1717330 ..........1717331 ..........1717420 ..........1717421 ..........17
17430 ..........1717431 ..........1717440 ..........1717441 ..........1717480 ..........1717481 ..........1717631 ..........1717641 ..........1717681 ..........1717930 ..........1717931 ..........17
19000 ..........3019010 ..........3019020 ..........3019030 ..........3019040 ..........3019050 ..........3019060 ..........3019100 ..........3019101 ..........3019102 ..........3019103 ..........3019105 ..........3019900 ..........3019901 ..........3019902 ..........30
20000 ..........2920001 ..........2920002 ..........2920003 ..........2920010 ..........2920012 ..........2920013 ..........2920020 ..........2920022 ..........2920023 ..........2920030 ..........2920032 ..........2920033 ..........2920040 ..........2920042 ..........2920043 ..........2920050 ..........2920052 ..........2920053 ..........2920060 ..........2920062 ..........2920063 ..........2920100 ..........2920101 ..........2520103 ..........2520105 ..........2520107 ..........2520110 ..........2520112 ..........2520113 ..........2520114 ..........2520117 ..........2520200 ..........2820201 ..........2820202 ..........2720300 ..........2520310 ..........2820900 ..........2420901 ..........2420902 ..........24
21000 ..........4021001 ..........4021002 ..........4021011 ..........4021022 ..........4021033 ..........40
Part No Page Part No Page Part No Page Part No Page Part No Page Part No Page Part No Page Part No Page
www.bartonmarine.com
57
Part number indexind
ex21034 ..........4021050 ..........4021055 ..........4021100 ..........4121101 ..........4121200 ..........4121201 ..........4121202 ..........4121210 ..........4121211 ..........4121212 ..........4121323 ..........4021641 ..........4121642 ..........4121643 ..........4121644 ..........41
22000 ..........3322010 ..........3322020 ..........3322030 ..........3322040 ..........3322050 ..........3322060 ..........3322100 ..........3322200 ..........3322210 ..........3322220 ..........3322221 ..........3322300 ..........3322301 ..........3322310 ..........3322311 ..........3322312 ..........3322900 ..........3322901 ..........33
24000 ..........2924001 ..........2924002 ..........2924003 ..........2924010 ..........2924012 ..........2924013 ..........2924020 ..........2924022 ..........2924023 ..........2924030 ..........2924032 ..........2924033 ..........2924040 ..........2924042 ..........2924043 ..........2924050 ..........2924052 ..........2924053 ..........2924060 ..........2924062 ..........2924063 ..........2924100 ..........2924101 ..........2524103 ..........2524105 ..........2524107 ..........2524110 ..........2524112 ..........2524113 ..........2524114 ..........2524117 ..........2524200 ..........2824201 ..........2824202 ..........2724300 ..........2524310 ..........28
24900 ..........2424901 ..........2424902 ..........24
25000 ..........3525010 ..........3525020 ..........3525030 ..........3525040 ..........3525050 ..........3525060 ..........3525100 ..........3525200 ..........3525210 ..........3525220 ..........3525221 ..........3525300 ..........3525301 ..........3525302 ..........3525303 ..........3525304 ..........3525310 ..........3525311 ..........3525900 ..........3525901 ..........35
26000 ..........3126010 ..........3126020 ..........3126030 ..........3126040 ..........3126050 ..........3126060 ..........3126101 ..........3126102 ..........3126103 ..........3126104 ..........3126110 ..........3126111 ..........3126900 ..........3126901 ..........3126902 ..........31
28000 ..........3228010 ..........3228020 ..........3228030 ..........3228040 ..........3228050 ..........3228060 ..........3228101 ..........3228102 ..........3228103 ..........3228104 ..........3228105 ..........3228110 ..........3228111 ..........3228112 ..........3228900 ..........3228901 ..........3228902 ..........32
30000 ..........2930001 ..........2930002 ..........2930003 ..........2930010 ..........2930012 ..........2930013 ..........2930020 ..........2930022 ..........2930023 ..........2930030 ..........2930032 ..........29
30033 ..........2930040 ..........2930042 ..........2930043 ..........2930050 ..........2930052 ..........2930053 ..........2930060 ..........2930062 ..........2930063 ..........2930100 ..........2930101 ..........2530103 ..........2530105 ..........2530107 ..........2530110 ..........2530112 ..........2530113 ..........2530114 ..........2530117 ..........2530200 ..........2830201 ..........2830202 ..........2730300 ..........2530310 ..........28
32000 ..........3732010 ..........3732020 ..........3732030 ..........3732040 ..........3732050 ..........3732060 ..........3732100 ..........3732101 ..........3732200 ..........3732201 ..........3732210 ..........3732211 ..........3732220 ..........3732221 ..........3732300 ..........3732301 ..........3732302 ..........3732304 ..........3732310 ..........3732311 ..........3732312 ..........3732900 ..........3732901 ..........37
40040 ..........5040041 ..........5040042 ..........5040050 ..........5040051 ..........5040052 ..........5040060 ..........5040061 ..........5040062 ..........5040080 ..........5040081 ..........5040082 ..........5040220 ..........5040221 ..........5040240 ..........5040241 ..........5040250 ..........5040251 ..........5040320 ..........5040340 ..........50
41130 ..........4341140 ..........42
41143 ..........4241150 ..........4241151 ..........4241152 ..........4241153 ..........4241483 ..........4341484 ..........4341496 ..........4341497 ..........4341517 ..........4341517 ..........43
42102 ..........4642200 ..........4642201 ..........4642300 ..........4942334 ..........4642335 ..........4642336 ..........4642356 ..........4642357 ..........4642358 ..........4642359 ..........4642400 ..........4642419 ..........4642422 ..........4642435 ..........4642450 ..........4642500 ..........4642519 ..........4642522 ..........4642535 ..........4642550 ..........4642600 ..........4642601 ..........4642700 ..........46
43001 ..........4743002 ..........4743003 ..........4743004 ..........4743011 ..........4743012 ..........4743013 ..........4743014 ..........4743101 ..........4743102 ..........4743103 ..........4743104 ..........4743105 ..........4743106 ..........4743201 ..........4743202 ..........4743203 ..........4743204 ..........4743205 ..........4743206 ..........4743600 ..........4743601 ..........47
44010 ............444020 ............444030 ............444035 ............444040 ............4
51250 ..........4451253 ..........4451254 ..........4451320 ..........4451322 ..........4451323 ..........4452000 ..........4452001 ..........44
52100 ..........4452110 ..........4452111 ..........4452120 ..........4552121 ..........4552140 ..........4552141 ..........4552142 ..........4552143 ..........4552144 ..........4552145 ..........45
60001 ..........51
60010 ..........52
60120 ..........5460121 ..........5460122 ..........5460123 ..........5460142 ..........4360142 ..........4460160 ..........4560161 ..........4560190 ..........5460191 ..........5460203 ..........5460204 ..........5460207 ..........5460208 ..........5460209 ..........5460210 ..........5460212 ..........5460304 ..........5360305 ..........5360306 ..........5360307 ..........5360308 ..........5360309 ..........5360310 ..........5560311 ..........5560312 ..........5560320 ..........5560321 ..........5560322 ..........5560323 ..........5560343 ..........5560344 ..........5560350 ..........5560404 ..........4560405 ..........4560406 ..........4560407 ..........4560410 ..........5360411 ..........5360420 ..........5360421 ..........5360422 ..........5360423 ..........5360700 ..........5560701 ..........5560702 ..........5560703 ..........5560708 ..........5560709 ..........5560750 ..........42
64801 ..........5464802 ..........5464803 ..........5464804 ..........5464805 ..........5464806 ..........5464807 ..........54
64808 ..........5464809 ..........5464810 ..........5464811 ..........5464812 ..........5464813 ..........5464814 ..........5464815 ..........5464816 ..........5464901 ..........5464902 ..........5464903 ..........5464904 ..........5464906 ..........5464907 ..........5464908 ..........5464909 ..........5464910 ..........5464912 ..........5464913 ..........5464914 ..........5464915 ..........5464916 ..........54
70100 ..........4870101 ..........4870104 ..........4870105 ..........4870106 ..........4870115 ..........4870116 ..........4870125 ..........4870126 ..........4870135 ..........4870136 ..........4870140 ..........4870141 ..........4870200 ..........4870201 ..........4870204 ..........4870205 ..........4870206 ..........4870215 ..........4870216 ..........4870225 ..........4870226 ..........4870235 ..........4870236 ..........4870240 ..........4870241 ..........4870300 ..........4870301 ..........4870304 ..........4870305 ..........4870306 ..........4870315 ..........4870316 ..........4870325 ..........4870326 ..........4870335 ..........4870336 ..........4870340 ..........4870341 ..........4870400 ..........4570401 ..........4570500 ..........4570501 ..........4570600 ..........4570601 ..........4570602 ..........45
80500 ..........3880501 ..........3880502 ..........38
81200 ..........2181500 ..........3981501 ..........3981502 ..........3981540 ..........3981541 ..........3981545 ..........3981546 ..........3981547 ..........3981548 ..........3981582 ..........3881583 ..........3881584 ..........3881585 ..........3881586 ..........3881682 ..........3881683 ..........3881684 ..........3881685 ..........3881686 ..........38
82100 ..........2182200 ..........2182300 ..........2182995 ..........2182996 ..........2182997 ..........2182998 ..........2182999 ..........21
90100 ..........2090101 ..........2090200 ..........2090201 ..........2090300 ..........2090301 ..........2090400 ..........2090401 ..........2090402 ..........20
91020 ..........1991040 ..........1991200 ..........1991300 ..........1991301 ..........1991302 ..........1991400 ..........1991500 ..........1991600 ..........1991650 ..........1991700 ..........1991750 ..........19
95100 ..........1895101 ..........1895102 ..........1895103 ..........1895104 ..........1895105 ..........1895120 ..........1895121 ..........1895122 ..........1895123 ..........1895130 ..........1895131 ..........1895132 ..........1895133 ..........1895137 ..........1895138 ..........1895139 ..........1895200 ..........1895201 ..........1895202 ..........1895203 ..........18
95204 ..........1895205 ..........1895220 ..........1895221 ..........1895222 ..........1895223 ..........1895230 ..........1895231 ..........1895232 ..........1895233 ..........1895300 ..........1895301 ..........1895302 ..........1895303 ..........1895304 ..........1895305 ..........1895320 ..........1895321 ..........1895322 ..........1895323 ..........1895330 ..........1895331 ..........1895332 ..........1895333 ..........1895400 ..........1895401 ..........1895402 ..........1895403 ..........1895404 ..........1895405 ..........1895420 ..........1895421 ..........1895422 ..........1895423 ..........1895430 ..........1895431 ..........1895432 ..........1895433 ..........1895437 ..........1895438 ..........1895439 ..........1895500 ..........1895501 ..........1895502 ..........1895503 ..........1895504 ..........1895505 ..........1895520 ..........1895521 ..........1895522 ..........1895523 ..........1895530 ..........1895531 ..........1895532 ..........1895533 ..........1895600 ..........1895601 ..........1895602 ..........1895603 ..........1895604 ..........1895605 ..........1895620 ..........1895621 ..........1895622 ..........1895623 ..........1895630 ..........1895631 ..........1895632 ..........1895633 ..........18
Part No Page Part No Page Part No Page Part No Page Part No Page Part No Page Part No Page Part No Page