Get commercial locksmith services at mr. locksmith north shore
The 2001 Dodge Stratus - LOCKSMITH...
Transcript of The 2001 Dodge Stratus - LOCKSMITH...
2. The car has cable linkage instead ofmetal rods. The latch mechanism
seems to be almost completely sealedfrom car opening tools. The weather-
stripping is nice and tight and it doesn’tseem like an over and under tool (caddykiller) could even get in there. I openedthe car with one of those “Jack” (JiffyJack, Ultra Jack, Super Jack, etc...)
tools every car opening company seems to have now. I just used an airwedge and the long metal rod that comes with one of those “Jack” tools.
This is a frameless door and take care with the glass. There is a littleledge that is on top of where the door glass sits in when the door is
closed. I had to wiggle the glass out of the ledge to get the air wedge in.It wasn’t a pretty sight but it did work without damage. There may be
others ways to open this car out soon after this article, whatever worksthe best for you.
IssueNo.26
The Official Publication of the
NATIONAL LOCKSMITHAUTOMOBILE ASSOCIATION™
™
08.01
The 2001 Dodge Stratusby Michael Hyde
www.TheNationalLocksmith.comChat, Forums, Editorial,
Online Store, Tech Support
www.Laserkey.comProduct & Technology Sales,
Transponder Information Resources
Here are the two best websites for Automotive Locksmiths:
Opening
1. This time out we are taking apart a 2001 Dodge Stratus R/T, 2-doorhardtop. The 2-door hard top Stratus and the 2-door Chrysler Sebringhardtop both use Mitsubishi locks and electronics. All models have the
transponder system. The keyway is the MIT6/X263 type with a chip. Strattecmakes the locks and keys for this car, use Strattec keying kit # 704605.
2 • Automotive Edge National Locksmith Automobile Association
National LocksmithAutomobile Association™
PublisherMarc Goldberg
DirectorGreg Mango
Printed in the U.S.A.NLAA, a division of the National
Publishing CompanyPublishers of
THE NATIONAL LOCKSMITH
1533 Burgundy ParkwayStreamwood, Illinois 60107
Phone 630-837-2044Fax 630-837-1210
E-mail address:[email protected]
Unsolicited manuscripts areaccepted, but must include SASE.
©2001 National Publishing Co.All rights reserved.
Issue No. 26
3. The ignition lockhas a transpondercoil around it andthe lock cylinder isthe active retainertype.
Ignition
4. To service the lock you will need to remove the 2-piece plastic shroud onthe steering column. There are four screws on the underside and there is 1
screw next to the ignition lock face.
National Locksmith Automobile Association Issue No. 26 • 3
5. The face of the ignitionlock has a transponder coilthat can be unsnapped and
moved to the side.
6. This is an active retainerignition. The retainer is atthe 9 o’clock position. You
must have a working key inthe “On” position. Depress
the retainer and release. Ifyou do not have a working
key you can alwaysimpression the lock or drill
the cylinder and replace.
4 • Automotive Edge National Locksmith Automobile Association
7. The ignition lock cylinderlooks pretty much like otherlate model Mitsubishiignition locks and verysimilar to Toyota ignitionlocks.
8. You will need toremove the tru-arcring on the back ofthe lock cylinder.
9. The lock cylinder plug has one ofthose buzzer detents that can fall outand onto the floor before you evennotice what happened to it.
National Locksmith Automobile Association Issue No. 26 • 5
10. The cylinder plugcontains all 8 tumblers fora complete key. There is
also a tumbler for the“Push-to-Lock” part of thelock; it does not interfere
with picking the lock.
Door
11. The door lock is part of theoutside handle. To service the lockcylinder you must first remove theinside door panel.
6 • Automotive Edge National Locksmith Automobile Association
12. On the rear edge ofthe panel is a screw thatmust be removed.
13. Inside the trim for the locking button is ascrew fastener that has to removed along withthe one on the front of the panel.
National Locksmith Automobile Association Issue No. 26 • 7
13. The door lock andwindow control panel needsto be lifted up anddisconnected.
14. Lift the control panel upfrom the rear section whereit is held with a tension clip.
8 • Automotive Edge National Locksmith Automobile Association
15. The front section of the control panel does notcome out first because of a molded plastic hook. Ihappened to lift it up from the front and broke the
plastic hook as seen in the photo. (There’s 30 bucks I’llnever see again.)
16. The inside handle door pull has a 10mm bolt and ascrew fastener hidden behind it’s trim on the top and
bottom sections.
17. The rest of the panelis held on with thestandard push-in styleplastic fasteners.
18. Once the panel is removed you can seethe plastic liner. Take care in pulling back
the liner as to not rip or stretch it.
2001 AutoSmart™Full Version Price: $95.00
2001 AutoSmart™Update Price: $45.00
All the new information on vehicles is here, current up to2001. Don't hesitate and lose car car jobs unnecessarily. Getyour 2001 AutoSmart™ now and you'll be in the driver'sseat for automotive locksmithing!
What's new for the 2001 book?• FREE Mid-Year updates due out in Summer '01.• Updated airbag info grid for EZ reference.• All the latest transponder information.• All new Strattec info: ignitions, door locks, trunk cylinders
and more.• All new ASP lock part info with EZ to read footnotes.• Jet key applications now integrated
throughout the keyblank charts.• Gives you every new spec and
method to make the first key.
The Autosmart™ alsocontains…• Manufacturer divider tabs for EZ reference.• The most accurate keyblank application guide
in the world.• EZ to read and use• Making the first key to almost all cars and trucks, even
high security.• Code locations, spacing and depths, tumbler charts.• Data and specs for almost every car on the road, foreign
and domestic.
OID
: 02/
01
A Must ForEvery
Locksmith!
2001AutoSmart
Is Here!
Copy or clip this coupon and send with payment to:The National Locksmith • P.O. Box 77-97592 • Chicago, IL 60678-7592
CHECK PAYMENT METHOD:r Check rMoney Order
Charge My…r VISA rMasterCardr Discover r American Express
Card # ____________________________________________________________Exp. Date ____________________
Signature (Required)_____________________________________________________________________________
Your Name ______________________________________________________________________________________
Shop Name ______________________________________________________________________________________
Address (No P.O. Boxes) _________________________________________________________________________
City _____________________________________________________________________________________________
State ____________________________________Zip Code_______________________________________________
Phone # ( ________________) ______________________________________________________________________
Buy it in the online store!
TheNationalLocksmith.com
Now with FREEMid-YearUpdates!
Foreign &Canada $20 s/h
Yes!r Send me a new2001AutoSmart™($95) plus $5 s/h.Order total is $100.
Yes!r Send me the2001AutoSmart™ Update($45) plus $5 s/h.Order total is $50.* Updates the 1999-2000 AutoSmart
or the 2000 AutoSmart only.
10 • Automotive Edge National Locksmith Automobile Association
19. Here’s a look at the door lock cylinderlooking up at it. As with most Japanese stylelocks it is held in with a metal ring that fits ina groove in the outside door handle.
20. Disconnect the linkage rod and then move themetal ring enough to slide the lock out. When you getthe lock out of the handle you will have more room toget the switch off the back of the lock cylinder. Makesure you mark it so you can reassemble it correctly.
21. It may be helpful to unsnap part ofthe rubber door weather-stripping toget a better view of the door lock whentrying to remove.
National Locksmith Automobile Association Issue No. 26 • 11
22. The door lock is disassembled pretty easy. There is a “C” clip holding the tailpiece on and the face cap is reusable.
23.The doorlock contains allthe tumblers fora complete key
24. Sometimes it can be a real pain toremove some of these “reusable” facecaps. I removed this one by prying upon a ledge where the cap meets thelock cylinder housing and then workingthe small screwdriver over to one ofthe dinged parts of the cap. Thismethod will sometime tear the cap alittle bit, but is easily fixed with a smallhammer after you put the cap back on.Besides the side of the cap is not seenanyways.
12 • Automotive Edge National Locksmith Automobile Association
Trunk
25. If you havenoticed the rearsection of thisredesigned Stratusnow looks like therear section of anIntrepid also. Thetrunk lock islocated on thepassenger (right)side of the lid.
26. The trunk lockcylinder is held inplace by a metalhorseshoe styleclip. This clip isvery sharp too!
National Locksmith Automobile Association Issue No. 26 • 13
27. On the bottomof the lock cylinderis a large openingfor the drain holewhich you can readthe tumblersthrough.
28. The trunk lock is disassembled pretty easy. There is a “C” clip holding the tailpiece on.The face cap is not reusable and there is currently not a specific Strattec part number for it yet. I
found an ASP Toyota cap that worked great, it is part # P-30-217, a very popular cap.
14 • Automotive Edge National Locksmith Automobile Association
Glovebox
30. The glove boxlock cylinder isalso the latchassembly for theglove box.
31. Remove the 2 screws on the inside of the glove box that holds the lock assembly in place.
National Locksmith Automobile Association Issue No. 26 • 15
32. This is another one of thosefamous Strattec glove box locks.
This one you have to rake thetumblers to pick while applying
counter-clockwise turning torque atthe 12 o’clock position, then depress
the very front tumbler (near thekeyway entrance) and rotate aquarter turn and slide out the
cylinder plug. There is an opening inthe top rear of the cylinder housing
allowing a small access cavity to thecombination tumblers and retainer
16 • Automotive Edge National Locksmith Automobile Association
33. Here is a look at the glove box cylinder plug. Thereare four combination tumblers and a retainer tumbler.
34. The factory key for this car is the Strattec 599450.This key has a transponder chip in it with a MIT6/X263style keyway. A Strattec 598992 may be substituted; ithas the same keyway and transponder chip, but has a
Mitsubishi bow on it.
Keys
Programming
35. There is no on-board programming for this carwithout the use of a MUT2 tester. It doesn’t matter
how many factory original keys they have, there is noon-board programming. The MUT2 tester is available
from National Auto Lock @ 800-954-5454.The MUT2 tester is required for all Mitsubishi vehicleswith a transponder system and the 2001 Dodge Stratus
R/T, 2-door hardtop & the 2001 Chrysler Sebring 2-door hardtop.
36. To program the new keys using the MUT2 tester,you must first connect the cable to the car’s OBD2
connector port and turn On the tester.
AutoSmart™ is the most comprehensive and popularautomotive locksmith manual in history. Acclaimed expert Michael Hyde againmakes history with AutoSmart Advisor™ software! You’ll have instant access to information, and bestof all...it’s amazingly easy to use! You may never need to read the manual.
Contains virtually every car and part known to man up through 2000. Gives all information you needto service the vehicle. Creates instant estimates for all automotive service jobs. Shows available ASPand Strattec part numbers and labor time. Can be user customized with your own service call, laborand tax rates.
Because it’s from the creator of AutoSmart™ you get all methods to make the first key, plus: u Code series u Key machine set up information u Tumbler chart u Information on ignition retainers,progressioning, airbags, code locations, key silhouettes, transponders,valet keys, all parts and model notes u Make your own user notes.u Includes NGS programming instructions
AutoSmart Advisor™ does everythinginstantly and accurately. Now your computeris the best automotive tool you own!
Installation and System requirements: License is grantedto run the software on any two computers you own.Installation on additional computers is available for $50 each.Requires 486 or better PC with Windows 95 or better and CDdrive. 75 megabytes of hard drive space. Installable from 17diskettes which you can create from the CD. 16 megabytes ofram. Not network compatible.
AutoSmarAutoSmar tt
AdvisorAdvisor™™
r YES! Send me the AutoSmart Advisor™ for $395 (installable on two computers) plus $5 for shipping and handling.Orders must be paid in U.S. funds.
r Send me _____ additional licenses for $50 each.
r Send me the 21 day full trial AutoSmart Advisor™ Demo for $10(credited toward full version purchase)
Select payment Method:
r VISA r MasterCard r Discoverr American Express r Money Order r Check
Order Total _________________
Card Number __________________________ Exp. Date ______________
Signature (required) __________________________________________
Name ______________________________________________________
Shop Name __________________________________________________
Address (no P.O. boxes) ________________________________________
City ______________________ State ________ Zip ________________
Phone______________________________________________________
E-Mail (optional)______________________________________________
Copy or clip this coupon and send with payment to:The National Locksmith • P.O. Box 77-97592 • Chicago, Illinois 60678-7592
Buy the it in the online store!
TheNationalLocksmith.comBuy the it in the online store!
TheNationalLocksmith.com
Take a tour online atwww.AutoSmartAdvisor.com
Take a tour online atwww.AutoSmartAdvisor.com
18 • Automotive Edge National Locksmith Automobile Association
37. From the Main Menu, select “System Select” andpress the “Yes” button.
38. Use the up and down arrow keys to select“Immobilizer” and press the “Yes” button.
39. Make sure you have your key in the ignition and turned to the “Run” position.
National Locksmith Automobile Association Issue No. 26 • 19
40. Use the up and down arrow keys to select “Specialfunc.” and press the “Yes” button.
41. Select “Key ID registr” and press the “Yes” button.
42. Use the arrow keys to enter the pin for this car andpress the “Yes” button.
NLAA1533 Burgundy ParkwayStreamwood, Illinois 60107
BULK RATEU.S. POSTAGE
PAIDDAYTONA BEACH, FL
PERMIT NO. 447
MAKING FIRST KEY:
Remove and decode tumblers in trunk lock to makemaster key. Program new keys with MUT2 tester.
43. If you are ready to proceed press the “Yes” button. 44. The key is registered and you can now addadditional keys.