TENDER ENQUIRY DOCUMENT FOR ESIC MEDICAL ...2014/01/13 · Tenderer to download the tender enquiry...
Transcript of TENDER ENQUIRY DOCUMENT FOR ESIC MEDICAL ...2014/01/13 · Tenderer to download the tender enquiry...
Page 1 of 43
TENDER ENQUIRY DOCUMENT FOR
ESIC MEDICAL COLLEGE SANATHNAGAR, HYDERABAD (AP)
FOR PURCHASE OF MEDICAL EQUIPMENTS
EMPLOYEES’ STATE INSURANCE CORPORATION MODEL HOSPITAL
NACHARAM, HYDERABAD-76. [email protected]
Phone no.- 040-27173315
Page 2 of 43
EMPLOYEES’ STATE INSURANCE CORPORATION MODEL HOSPITAL
NACHARAM, HYDERABAD [email protected]
Phone no.- 040-27173315
NOTICE INVITING TENDERS (NIT) Tender Enquiry No.52-U-SS-16-67/ESIC/NR/14
Medical Superintendent, ESIC Model Hospital, Nacharam, Hyderabad, Andhra
Pradesh invites sealed tenders from eligible and qualified tenderers for supply of Medical Equipments (as per attachment) for proposed ESIC Medical college, Sanathnagar, Hyderabad The schedule for different activities are as below:
Sr. No. Description Schedule
1. Human Anatomy Last date and time of submission Upto 02.00p.m. on dt:12-02-2014
Date and time of opening of tender At 03.00 p.m.on dt:12-02-2014
2. Biochemistry Last date and time of submission Upto 02.00p.m. on dt:12-02-2014
Date and time of opening of tender
At 03.00 p.m.on dt:13-02-2014
3. Human Physiology & Clinical Physiology Last date and time of submission Upto 02.00p.m. on dt:12-02-2014
Date and time of opening of tender
At 03.00 p.m.on dt:14-02-2014
Tenderer to download the tender enquiry documents free of cost from the web site
www.esic.nic.in and submit its tender by utilizing the downloaded document. Tenderers shall ensure that their tenders, complete in all respects, are dropped in the
Tender Box located at the office of Medical Superintendent, ESIC Model Hospital, Nacharam, Hyderabad, Andhra Pradesh on or before the closing date and time indicated above, failing which the tenders will be treated as late tender and rejected.The tenders sent by post/Courier must reach the above said address on or before the closing date & time indicated above, failing which the tenders will be treated as late tender and rejected.
In the event of any of the above mentioned dates being declared as a holiday / closed day for the purchase organisation, the tenders will be sold/received/opened on the next working day at the appointed time.The Tender Enquiry Documents are not transferable.
All Tenders must be accompanied by EMD as mentioned against each item. Tenders without EMD shall be rejected.
Dr. R.K.Kataria Medical Superintendent
Page 3 of 43
EMPLOYEES’ STATE INSURANCE CORPORATION MODEL HOSPITAL
NACHARAM, HYDERABAD-76. [email protected]
Phone no.- 040-27173315
Tender Enquiry No.52-U-SS-16-67/ESIC/NR/14
TENDER DOCUMENT
Sealed tenders are invited by Medical Superintendent ESIC Model Hospital Nacharam, Hyderabad for
the supply of following items at ESIC Medical college, Sanathnagar, Hyderabad.
Sl.
No.
Name of the equipment Total
qty.
EMD (Rs.) Bid system
Human Anatomy
1. Electrically operated hand drill 02 No.s Rs:500/- Single
2. Handsaw (S.S) 06 No.s Rs:500/- Single
3. Band saw for sectioning body and limbs 02 No.s Rs:500/- Single
4. Brain knife( S.S)Slicing /Meat knife 06 No.s Rs:500/- Single
5. Specimen jar/Acrylic & Plastic tanks for storing
soft and dissected parts
20 No.s Rs:500/- Single
6. Medical stool revolving with back rest 500 No.s Rs:500/- Single
7. Dissecting instruments set of 17 10 No.s Rs:500/- Single
8. Diamond pencils or glass marking pencils 08 No.s Rs:500/- Single
9. Bones(disarticuted)sets 50 No.s Rs:500/- Single
10. Dissection Table-SS Standard
Size:6”.1”X2”X3”
Full/large
15 no’s Rs: 5000/- Two
11. Dissection Table-SS Standard
Size:6”.1”X2”X3”
a)Half
10no's
Rs.2000/- Single
12. Embalming work station with embalming
,machine or cadever injector
02 No.s Rs.2000/- Single
13. Meat cutting machine for thin body scetions (
trans &vertical) for gross anatomy sectional
study
02 No.s Rs.1000/- Single
14. Mortuary cooler with arrangement to keep 6
bodies
02 No.s Rs.1000/- Single
15. Portable LCD Projector with dedicated
computer system
02 No.s Rs.1500/- Single
16. Simple S.S Stretcher trolley for cadever
transport
06 No.s Rs:500/- Single
17. Research Microscope 02 No.s Rs.2000/- Single
18. Pre Prepared Histology slides 05No.s Rs.1000/- Single
Page 4 of 43
19. Microtome,Sledge,large cutting 02No.s Rs.1000/- Single
20. Cabinet for slides(1000 wooden/plastic) 12 No.s Rs:500/- Single
21. Incubator 02 No.s Rs.1500/- Single
22. Paraffin Embedding bath(6 cup and 8sieves) 02no’s Rs:500/- Single
23. Hot plates for flattering sections (slide
warming table)18 x 12”
02no’s Rs:500/- Single
24. Balance Analytical 02no’s Rs:1000/- Single
25. Colour markers 10 No’s Rs:500/- Single
26. Balance ear hanger 04 no’s Rs:500/- Single
27. Distilled water still with stainless steel,wall
mountable model
04 no’s Rs:500/- Single
28. Laboratory Refrigerator 04 No.s Rs.2000/- Single
29. All Quartz distillation apparatus 5 liter capacity 01No Rs.5000/- Two
30. X-Ray viewing lobby(double or 4 films) 06no’s Rs.5000/- Two
31. Dissection Microscope-Stereo type 10 No.s Rs.5000/- Two
32. Hot air oven for drying slides(45 degree
celsius) 18”X18”X18”
02 No.s Rs.3000/- Two
33. Laminated photographs-Chart of various
hiostology slides
240 No.s Rs.500/- Single
34. Skeletons articulated with stand to hold
Skeleton
10 No.s Rs.3000/- Two
35. Mobile or portable pedestal operating-
Surgical light
12 No.s Rs.24000/
-
Two
36. Monocular Microscope (Compound
Microscope)
120 No.s Rs.12000/
-
Two
37. Semi Automatic Rotary Microtome 02 No.s Rs.16000/
-
Two
38. Racks of anatomy museum specimens-
museum Racks with study table facilities
40 No.s Rs.10,000
/-
Two
39. Museum jars 40 No.s Rs.2000/- Single
40. Chart –Illustrative-laminated photographs 40 No.s Rs.2000/- Single
41. 3D models in organic system and complete
set of Embryology
40 No.s Rs.2000/- Single
Bio -Chemistry
42. Urinometer 100 No.s Rs.500/- Single
43. Ryles tube 08 No.s Rs.500/- Single
44. Thermometer 20 No.s Rs.500/- Single
45. Wet & dry thermometer 04 No.s Rs.500/- Single
Page 5 of 43
46. Cork-Borer set 02 No.s Rs.500/- Single
47. Stop watch digital 08 No.s Rs.500/- Single
48. Bottle dispense Indian 30 No.s Rs.500/- Single
49. Vortex mixer 04 No.s Rs.500/- Single
50. Magnetic stirrer with hot plate 04 No.s Rs.500/- Single
51. Vaccum pump 04 No.s Rs.2000/- Single
52. Chromatographic chamber 04 No.s Rs.500/- Single
53. Distilled water with stainless steel ,wall
mountable model
06 No.s Rs.1500/- Single
54. Laboratory dissector large size 12 No.s Rs.1500/- Single
55. Laboratory dissector small size 12 No.s Rs.1500/- Single
56. UV lamp with fittings 02 No.s Rs.1500/- Single
57. Spirit lamp stainless steel 100 No.s Rs.2000/- Single
58. Fume cupboard 120X60X60 cms 04 No.s Rs.8000/- Two
59. Water bath rectangular(Thermostatic control/
having 8-12 Holes)
12 No.s Rs.8000/- Two
60. Auto clave Vertical model-Elctrically operated 04 No.s Rs.4500/- Two
61. Balance open pan type 12 No.s Rs.4000/- Two
62. Balance Semi Micro 04 No.s Rs.2500/- Two
63. Balance Micro (Electronic) 04 No.s Rs.2500/- Two
64. Constant temperature water bath 08 No.s Rs.4000/- Two
65. Laboratory Incubator Elecrtic with Thermostat 08 No.s Rs.5000/- Two
66. Hot air oven 08 No.s Rs.5000/- Two
67. Colorimeter 12 No.s Rs.4000/- Two
68. Flame Photometer 04 No.s Rs.4500/- Two
69. All glass (quartz)double distillation apparatus 06 No.s Rs.6000/- Two
70. High speed centrifuge 12 No.s Rs.5000/- Two
71. pH meter 06 No.s Rs.3000/- Two
72. Tissue homogeniser complete set 06 No.s Rs.4000/- Two
73. Samplers or auto pipettes 30 No.s Rs.3000/- Two
74. Monocular microscope 12 No.s Rs.3000/- Two
75. Binocular microscope -research microscope 06No.s Rs.5000/- Two
76. Refrigerator 350liters 08 No.s Rs.7500/- Two
77. Paper electrophoresis apparatus 12 No.s Rs.11000/
-
Two
Page 6 of 43
78. Spectro photometer 02 No.s Rs.12000/
-
Two
HUMAN PHYSIOLOGY
79. Haemocytometer inclusive of Neubauer
counting chamer,RBC,WBC pipettes
contained in a box
120 No.s Rs.3000/- Two
80. Sahli (Sahli-Adams) hemoglobinometer 120No.s Rs.2500/- Two
81. All Quartz distillation apparatus 5 liter capacity 01 NO Rs.5000/- Two
82. Monocular microscope 120 No.s Rs.12000/
-
Two
83. Incubator 02 No.s Rs.700/- Single
CLINICAL PHYSIOLOGY
84. Stethography 12 No.s Rs.600/- Single
85. Compact CPR training mannequins 01no Rs.500/- Single
86. Apparatus for continous passive motion 02 No.s Rs.500/- Single
87. Dynamometer 02 No.s Rs.500/- Single
88. Steriliser electric Mediu, Size 06 No.s Rs.500/- Single
89. Water distillation apparatus 04 No.s Rs.500/- Single
90. Wrigght”s peak flow meter 06 No.s Rs.1500/- Single
91. Mosso”s ergography 12 No.s Rs.1500/- Single
92. Audiometry 02 No.s Rs.1000/- Single
93. Clinical examination couches 02 No.s Rs.1000/- Single
94. Bicycle ergometer 02 No.s RS.700/- Single
95. Instrument trolley 06 No.s Rs.600/- Single
96. Centrifuge high speed with telecometer 12 No.s Rs.500/- Single
97. Calorimeter 04 No.s Rs.700/- Single
98. PH meter 04 NO.s Rs.1000/- Single
99. Electronic muscle stimulator 04 No.s Rs.500/- Single
100. Balance analytical 04 No.s Rs.500/- Single
101. Laboratory Refrigerator 04 No.s Rs.2000/- Single
102. Recording spirometer-Benedict”s Roth
Spirometer- Apparatus
06 No.s Rs.4000/- Two
103. ECG single channel 06 No.s Rs.2500/- Two
104. ECG Machine multi channel 06 No.s Rs.10000/
-
Two
105. EEG Machine Recorder portable 02 No.s Rs.7000/- Two
106. Physiopgraph 06 No.s Rs.10000/ Two
Page 7 of 43
-
107. Experimetal physiology 06 No.s Rs.5000/- Two
108. Spirometry system 12 No.s Rs.11000/
-
Two
109. Computerized PFT interpretation facillities 06 No’s Rs.2000/- Single
110. Mechanical Respirators 02 No’s Rs.2000/- Single
111. Electro myogram 02 No’s Rs.2000/- Single
112. Multi channel polygraph computerized 02 No’s Rs.2000/- Single
Page 8 of 43
GENERAL INSTRUCTIONS TO TENDERERS
A. PREAMBLE 1. Definitions and Abbreviations 1.1 The following definitions and abbreviations, which have been used in these documents shall have the meanings as indicated below: 1.2. Definitions: (i) “Purchaser” means the organization purchasing goods and services as incorporated in the Tender Enquiry document. (ii) “Tender” means Bids / Quotation / Tender received from a Firm / Tenderer / Bidder. (iii) “Tenderer” means Bidder/ the Individual or Firm submitting Bids / Quotation / Tender (iii) “Supplier” means the individual or the firm supplying the goods and services as incorporated in the contract. (iv) “Goods” means the articles, material, commodities, livestock, furniture, fixtures, raw material, spares, instruments, machinery, equipment, medical equipment, industrial plant etc. which the supplier is required to supply to the purchaser under the contract. (v) “Services” means services allied and incidental to the supply of goods, such as transportation, installation, commissioning, provision of technical assistance, training, after sales service, maintenance service and other such obligations of the supplier covered under the contract. (vi) “Earnest Money Deposit” (EMD) means Bid Security/ Monetary or financial gaurantee in the form to be furnished by a tenderer along with its tender. (vii) “Contract” means the written agreement entered into between the purchaser and/or consignee and the supplier, together with all the documents mentioned therein and including all attachments, annexure etc. therein. (viii) “Performance Security” means money or in the form of D.D to be furnished by the successful tenderer for due performance of the contract placed on it. Performance Security is also known as Security Deposit. (ix) “Consignee” means the Hospital/Dispensaries/Institute/Medical College/ person to whom the goods are required to be delivered as specified in the Contract. If the goods are required to be delivered to a person as an interim consignee for the purpose of despatch to another person as provided in the Contract then that “another” person is the consignee, also known as ultimate consignee. (x) “Specification” means the document/standard that prescribes the requirement with which goods or service has to conform. (xi) “Inspection” means activities such as measuring, examining, testing, gauging one or more characteristics of the product or service and comparing the same with the specified requirement to determine conformity. (xii) “Day” means calendar day. 2. Language of Tender
The tender submitted by the tenderer and all subsequent correspondence and documents relating to the tender exchanged between the tenderer and the purchaser, shall be written in the English language, unless otherwise specified in the Tender Enquiry. However, the language of any printed literature furnished by the tenderer in connection with its tender may be written in any other language provided the same is accompanied by a notarised English translation and, for purposes of interpretation of the tender, the English translation shall prevail.
The tender submitted by the tenderer and all subsequent correspondence and documents relating to the tender exchanged between the tenderer and the purchaser, may also be written in the Hindi language, provided that the same are accompanied by notarised English translation, in which case, for purpose of interpretation of the tender etc, the English translations shall prevail. 3. Eligible TenderersThis invitation for tenders is open to all suppliers who fulfil the eligibility criteria specified in this documents. 4. Eligible Goods and Services All goods and related services to be supplied under the contract shall have their origin in India or any other country with which India has not banned trade relations. The term “origin” used in this clause means the place where the goods are mined, grown, produced, or manufactured or from where the related services are arranged and supplied B. PREPARATION OF TENDERS 5. Documents Comprising the Tender for each system are as below. Single bid System
Tenderers are to submit in single sealed bid, super scribing as “Single bid Tender for Equipment
(Name of the equipment) due on --------------. The envelope should have the name of the quoting
Page 9 of 43
company, last date of submission of tender. Each and every page of the quotation should be
separately numbered and duly signed. The tender/s should be put in sealed envelope addressed to
the Medical Superintendent, ESIC Model Hospital , Nacharam.
Rates/Price should be typed both in words as well as in figures, free from erasing, cutting and over-writing
Each and every page of the quotation be separately numbered and duly signed.
Price and S.T./ VAT must be quoted separately. The price should be all inclusive lump sum
including cost of the equipment, freight, insurance, transit insurance, packing forwarding etc. and
including charges for installation and commissioning with all the men and material required for the
same and for the quoted warranty period.
The price should be on F.O.R. ESIC Medical college, Sanath nagar basis. No other charges in
addition will be payable on any account over and above the lump sum price quoted in the price bid
except S.T/VAT. The rates quoted in ambiguous terms such as “Freight on actual basis” or “Taxes
as applicable extra” or “Packing forwarding extra” will render the bid liable to rejection.
The price should be quoted in I.N.R.
The price quoted by the tenderer for indigenous/imported goods shall not be higher than the lowest price charged for the goods of the same nature, class or description to an individual/ firm/ organisation or department of Govt. of India.
5.2 The Two Tender System, i.e. “Techno – Commercial Tender” and “Price Tender” prepared by the tenderer shall comprise the following: A) Techno – Commercial Tender (Un priced Tender) i) Earnest money furnished in accordance with TE document ii) Tender Form iii) Tenderer/Agent who quotes for goods manufactured by other manufacturer shall furnish Manufacturer’s Authorisation in the prescribed format as per Annexure-II iv) Power of Attorney/Authorisation in favour of signatory of TE documents v) Performance Statement along with relevant copies of purchase orders and end users’ satisfaction certificate. vi) Price Schedule(s) filled up with all the details including Qty., Make, Model, Country of origin, etc. of the goods offered with prices blank (without indicating any prices). vii) Checklist as per Annexure - I B) Price Tender: The information given at clause no. 5.1 (vi) above should be reproduced with the prices indicated. 1. All pages of the Tender should be page numbered and indexed. 2. It is the responsibility of tenderer to go through the TE document to ensure furnishing all required documents in addition to above, if any. 5.2 The authorized signatory of the tenderer must sign the tender duly stamped at appropriate places and initial all the remaining pages of the tender. 5.3 A tender, which does not fulfil any of the above requirements and/or gives evasive information/reply against any such requirement, shall be liable to be ignored and rejected. 5.4 Tender sent by fax/telex/cable/electronically shall be ignored. 6. Tender currencies 6.1 The tenderer supplying indigenous goods or already imported goods shall quote only in Indian Rupees. 6.2 For imported goods if supplied directly from abroad, prices shall be quoted in Indian rupees. As regards price(s) for allied services, if any required with the goods, the same shall be quoted in Indian Rupees only if such services are to be performed /undertaken in India. 6.3 Tenders, where prices are quoted in any other way shall be treated as non-responsive and rejected. 7. Tender Prices 7.2 The tenderer has the option to submit its quotation for any one or more item (s) in the List of Requirements. However, separate sealed cover to be used for each item for price bid. 7.3 The quoted prices for goods offered from within India and that for goods offered from abroad are to be indicated separately in the applicable Price Schedules.
Page 10 of 43
The price quoted by the tenderer for indigenous/imported goods shall not be higher than the lowest price charged for the goods of the same nature, class or description to an individual/ firm/ organisation or department of Govt. of India.
If it is found at any stage that the goods as stated have been supplied at a lower price, then that price, with due allowance for elapsed time will be applicable to the present case and the difference in cost would be refunded by the supplier to the purchaser, if the contract has already been concluded. 7.4 While filling up the columns of the Price Schedule, the following aspects should be noted for compliance: 7.4.1 For domestic goods or goods of foreign origin located within India, the prices in the corresponding price schedule shall be entered separately in the following manner: a) the price of the goods, quoted ex-factory/ ex-showroom/ ex-warehouse/ off-the-shelf, as applicable, including all taxes and duties like sales tax, CST VAT, CENVAT, Custom Duty, Excise Duty etc. already paid or payable on the components and raw material used in the manufacture or assembly of the goods quoted ex-factory etc. or on the previously imported goods of foreign origin quoted ex-showroom etc; b) any sales or other taxes and any duties including excise duty, which will be payable on the finished goods in India if the contract is awarded; c) charges towards Packing & Forwarding, Inland Transportation, Insurance, Loading/Unloading and other local costs incidental to delivery of the goods to their final destination as specified in the List of Requirements and Price Schedule; d) the price of Incidental Services, as mentioned in List of Requirements and Price Schedule e) the price of CMC, as mentioned in List of Requirements, Technical Specification and Price Schedule. 8. Indian Agent 8.1 If a foreign tenderer has engaged an agent in India in connection with its tender, the foreign tenderer, in addition to indicating Indian agent’s commission, if any shall also be furnished. a) The complete name and address of the Indian Agent and its permanent income tax account number as allotted by the Indian Income Tax authority. b) The details of the services to be rendered by the agent for the subject requirement. c) Details of Service outlets in India, nearest to the consignee(s), to render services during Warranty and CMC period. 9. Earnest Money Deposit (EMD) The earnest money shall not be accepted in any other form except the following: i. Account Payee Demand Draft or ii. Banker’s cheque
The demand draft or banker’s cheque shall be drawn on any commercial bank in India or country of the tenderer, in favour of the ESIC account no.-I, payable at Hyderabad.
Unsuccessful tenderers’ earnest money will be returned to them without any interest,
after expiry of the tender validity period, but not later than thirty days after conclusion of the resultant contract. Successful tenderer’s earnest money will be returned without any interest, after receipt of performance security from that tenderer.
Earnest Money is required to protect the purchaser against the risk of the Tenderer’s conduct, which would warrant the forfeiture of the EMD. Earnest money of a tenderer will be forfeited, if the tenderer withdraws or amends its tender or impairs or derogates from the tender in any respect within the period of validity of its tender or if it comes to notice that the information/documents furnished in its tender is incorrect, false, misleading or forged without prejudice to other rights of the purchaser. The successful tenderer’s earnest money will be forfeited without prejudice to other rights of Purchaser if it fails to furnish the required performance security within the specified period. 10. Tender Validity The tenders shall remain valid for acceptance for a period of 120 days (One hundred and twenty days) after the date of opening of techno-commercial tenders prescribed in the TE document. Any tender valid for a shorter period shall be treated as unresponsive and rejected. 11. Signing and Sealing of Tender
All the copies of the tender shall be duly signed at the appropriate places as indicated in the TE documents and all other pages of the tender including printed literature, if any, shall be initialled by the same person(s) signing the tender. The tender shall not contain any erasure or
Page 11 of 43
overwriting, except as necessary to correct any error made by the tenderer and, if there is any such correction; the same shall be initialled by the person(s) signing the tender.
TE document seeks quotation following two Bid System, in two parts. First part will be known as ‘Techno - Commercial Tender’, and the second part ‘Price Tender’. Tenderer shall seal ‘Techno - Commercial Tender (along with envelope containing EMD)’ and ‘Price Tender’ separately and covers will be suitably super scribed.
Both these sealed covers shall be put in a bigger cover and sealed. C. SUBMISSION OF TENDERS The tenderers are to deposit the tenders in the tender box kept for this purpose at the office of Medical Superintendent, ESIC Model Hospital, Nacharam, Hyderabad, Andhra Pradesh.
The tenderers must ensure that they deposit their tenders not later than the closing time and date specified for submission of tenders. It is the responsibility of the tenderer to ensure that their Tenders whether sent by post or by courier or by person, are dropped in the Tender Box by the specified clearing date and time. In the event of the specified date for submission of tender falls on / is subsequently declared a holiday or closed day for the purchaser, the tenders will be received up to the appointed time on the next working day. A tender, which is received after the specified date and time for receipt of tenders will be treated as “late” tender and will be ignored. D. TENDER OPENING 12. Opening of Tenders
The purchaser will open the tenders at the specified date and time and at the specified place as indicated in the TED. In case the specified date of tender opening falls on / is subsequently declared a holiday or closed day for the purchaser, the tenders will be opened at the appointed time and place on the next working day.
Authorized representatives of the tenderers, who have submitted tenders on time may attend the tender opening provided they bring with them letters of authority from the corresponding tenderers.
The Techno-Commercial Tenders are to be opened in the first instance, at the prescribed time and date as indicated in TED. These Tenders shall be scrutinized and evaluated by the competent committee/authority with reference to parameters prescribed in the TE document. During the Techno -Commercial Tender opening, the tender opening official(s) will read the salient features of the tenders like brief description of the goods offered, delivery period, Earnest Money Deposit and any other special features of the tenders, as deemed fit by the tender opening official(s).
Thereafter, in the second stage, the Price Tenders of only the Techno-Commercially acceptable offers shall be opened at a later date which will be notified to such tenderers. The prices, special discount if any of the goods offered etc., as deemed fit by tender opening official(s) will be read out. E. AWARD OF CONTRACT Purchaser’s Right to accept any tender and to reject any or all tenders The purchaser reserves the right to accept in part or in full any tender or reject any or more tender(s) without assigning any reason or to cancel the tendering process and reject all tenders at any time prior to award of contract, without incurring any liability, whatsoever to the affected tenderer or tenderers. 13. Notification of Award
Before expiry of the tender validity period, the purchaser will notify the successful tenderer(s) in writing, by registered / speed post or by fax/ telex/cable (to be confirmed by registered / speed post) that its tender for goods & services, which have been selected by the purchaser, has been accepted, also briefly indicating therein the essential details like description, specification and quantity of the goods & services and corresponding prices accepted. The successful tenderer must furnish to the purchaser the required performance security within twenty-one (21) days from the date of dispatch of this notification, failing which the EMD will be forfeited and the award will be cancelled. 14. Return of EMD The earnest money of the successful tenderer and the unsuccessful tenderers will be returned to them without any interest. 15. Publication of Tender Result The name and address of the successful tenderer(s) receiving the contract(s) will be mentioned in the notice board/web site of the purchaser. 15. Corrupt or Fraudulent Practices It is required by all concerned to observe the highest standard of ethics during the procurement and execution of such contracts. The purchaser (b) will reject a proposal for award if it determines that the Tenderer recommended for award has engaged in corrupt or fraudulent practices in competing for the contract in question;
Page 12 of 43
(c) will declare a firm ineligible, either indefinitely or for a stated period of time, to be awarded a contract by the purchaser if it at any time determines that the firm has engaged in corrupt or fraudulent practices in competing for, or in executing the contract. 17. Inspection, Testing and Quality Control
The purchaser and/or its nominated representative(s) will, without any extra cost to the purchaser, inspect and/or test the ordered goods and the related services to confirm their conformity to the contract specifications and other quality control details incorporated in the contract. The purchaser shall inform the supplier in advance, in writing, the purchaser’s programme for such inspection and, also the identity of the officials to be deputed for this purpose. 18. Warranty 18.1 The supplier warrants comprehensively that the goods supplied under the contract is new, unused and incorporate all recent improvements in design and materials unless prescribed otherwise by the purchaser in the contract. The supplier further warrants that the goods supplied under the contract shall have no defect arising from design, materials or workmanship or from any act or omission of the supplier that may develop under normal use of the supplied goods under the conditions prevailing in India. 18.2 This warranty shall remain valid for 2 (Two) years in general, after the goods or any portion thereof as the case may be, have been delivered to the final destination and installed and commissioned at the final destination and accepted by the Purchaser/Consignee in terms of the contract, unless specified in the TED. a. No conditional warranty like mishandling, manufacturing defects etc. will be acceptable. b. Warranty as well as Comprehensive Maintenance contract will be inclusive of all accessories and Turnkey 18.3 In case of any claim arising out of this warranty, the Purchaser/Consignee shall promptly notify the same in writing to the supplier. 18.5 above irrespective of any other period mentioned elsewhere in the bidding documents. 18.6 Upon receipt of such notice, the supplier shall, within 8 hours on a 24(hrs) X 7 (days) X 365 (days) basis respond to take action to repair or replace the defective goods or parts thereof, free of cost, at the ultimate destination. The supplier shall take over the replaced parts/goods after providing their replacements and no claim, whatsoever shall lie on the purchaser for such replaced parts/goods thereafter. The penalty clause for non-rectification will be applicable as per tender conditions 18.7 In the event of any rectification of a defect or replacement of any defective goods during the warranty period, the warranty for the rectified/replaced goods shall be extended to a further period of two years. 18.8 If the supplier, having been notified, fails to respond to take action to repair or replace the defect(s) within 8 hours on a 24(hrs) X 7 (days) X 365 (days) basis, the purchaser may proceed to take such remedial action(s) as deemed fit by the purchaser, at the risk and expense of the supplier and without prejudice to other contractual rights and remedies, which the purchaser may have against the supplier. 19. Taxes and Duties Supplier shall be entirely responsible for all taxes, duties, fees, levies etc. incurred until delivery of the contracted goods to the purchaser. 20. Terms and Mode of Payment Payment Terms Payment shall be made subject to recoveries, if any, by way of liquidated damages or any other charges as per terms & conditions of contract in the following manner. A) Payment for Domestic Goods Or Foreign Origin Located Within India. Payment shall be made in Indian Rupees as specified in the contract in the following manner: a) On delivery: 90 % payment of the contract price shall be paid on receipt of goods in good condition and upon the submission of the following documents: (i) Four copies of supplier’s invoice showing contract number, goods description, quantity, unit price and total amount; (ii) Consignee Receipt Certificate in original issued by the authorized representative of the consignee; (iii) Two copies of packing list identifying contents of each package; (iv) Inspection certificate issued by the nominated Inspection agency, if any; (vi) Certificate of origin. b) On Acceptance: i)Balance 10 % payment would be made against ‘Final Acceptance Certificate’ of goods to be issued by the consignees subject to recoveries, if any, either on account of non-rectification of defects/deficiencies not attended by the Supplier or otherwise. B) Payment for Imported Goods:
Page 13 of 43
Payment for imported goods shall be made in the Indian currency as specified in the contract in the following manner: a) On delivery: Ninety (90) % of the e goods shipped shall be paid through irrevocable, non-transferable Letter of Credit (LC) in Indian currency opened in favour of the supplier in a bank in his country and upon submission of documents specified hereunder: (i) Four copies of supplier’s invoice showing contract number, goods description, quantity, unit price and total amount; (ii) Original and four copies of the negotiable clean, on-board Bill of Lading/ Airway bill, marked freight pre paid and four copies of non-negotiable Bill of Lading/Airway bill; (iii) Four Copies of packing list identifying contents of each package; (iv) Insurance Certificate and documents also to be submitted for payment of LC confirming that dispatch documents has already been sent within 24 hours to all concerned as per the contract; (v) Manufacturer’s/Supplier’s warranty certificate; (vi) Manufacturer’s own factory inspection report and (vii) Certificate of origin by the chamber of commerce of the concerned country; (viii) Inspection Certificate for the despatched equipments issued by recognized/ reputed agency like SGS, Lloyd or equivalent (acceptable to the purchaser) prior to despatch. (ix) Consignee Receipt Certificate as per Section XVII in original issued by the authorized representative of the consignee C) On Acceptance: i)Balance payment of 10 % of net CIP price of goods would be made against ‘Final Acceptance Certificate’ Letter of Credit (LC) in Indian rupees opened in favour of the Foreign Principal in a bank in his country, subject to recoveries, if any. ii) Payment of custom duty amount with Custom Duty Exemption Certificate (CDEC), if applicable, customs clearance and handling charges, loading/ unloading, inland transportation, incidental costs till consignee site & incidental services (including installation & commissioning, supervision, demonstration and training) will be paid by the tenderer.
ii) Payment of Indian Agency Commission: Indian Agency commission will be paid to the manufacturer’s agent in the local currency for an amount in Indian rupees indicated in the relevant Price Schedule (as per prevailing rate of exchange ruling on the date of Contract) and shall not be subject to further escalation /exchange variation. Payment shall be made after 100% payment to the Foreign Principal. D) Payment for Annual Comprehensive Maintenance Contract (CMC) Charges: i)The consignee will enter into CMC with the supplier at the rates as stipulated in the contract. The payment of CMC will be made on six monthly basis after satisfactory completion of said period, duly certified by the consignee. ii)The supplier shall not claim any interest on payments under the contract. iii)Irrevocable & non-transferable LC shall be opened by ESIC/ Purchaser. However, if the supplier requests specifically to open confirmed LC, the extra charges would be borne by the supplier. If LC is required to be extended and/or amended for reasons not attributable to the purchaser/consignee, the charges thereof shall be borne by the supplier. iv) The payment shall be made in the currency / currencies authorised in the contract. v) The supplier shall send its claim for payment in writing, when contractually due, along with relevant documents etc., duly signed with date, to the purchaser. vi)While claiming payment, the supplier is also to certify in the bill that the payment being claimed is strictly in terms of the contract and all the obligations on the part of the supplier for claiming that payment has been fulfilled as required under the contract. vii)While claiming reimbursement of duties, taxes etc. (like sales tax, excise duty, custom duty) from the Purchaser/Consignee, as and if permitted under the contract, the supplier shall also certify that, in case it gets any refund out of such taxes and duties from the concerned authorities at a later date, it (the supplier) shall refund to the Purchaser/Consignee forthwith. viii)In case where the supplier is not in a position to submit its bill for the balance payment for want of receipted copies of Inspection Note from the consignee and the consignee has not complained about the non-receipt, shortage, or defects in the supplies made, balance amount will be paid by the paying authority without consignee’s receipt certificate after three months from the date of the preceding part payment for the goods in question, subject to the following conditions: (a) The supplier will make good any defect or deficiency that the consignee (s) may report within six months from the date of despatch of goods. (b) The contract price where it is subject to variation has been finalized. (c) The supplier furnishes the following undertakings:
Page 14 of 43
“I/We, __________ certify that I/We have not received back the Inspection Note duly receipted by the consignee or any communication from the purchaser or the consignee about non-receipt, shortage or defects in the goods supplied. I/We ______ agree to make good any defect or deficiency that the consignee may report within three months from the date of receipt of this balance payment. 21. Termination for insolvency 25.1 If the supplier becomes bankrupt or otherwise insolvent, the purchaser reserves the right to terminate the contract at any time, by serving written notice to the supplier without any compensation, whatsoever, to the supplier, subject to further condition that such termination will not prejudice or affect the rights and remedies which have accrued and / or will accrue thereafter to the Purchaser/Consignee. 22. Force Majeure 26.1 Notwithstanding the provisions contained in TED the supplier shall not be liable for imposition of any such sanction so long the delay and/or failure of the supplier in fulfilling its obligations under the contract is the result of an event of Force Majeure. 26.2 For purposes of this clause, Force Majeure means an event beyond the control of the supplier and not involving the supplier’s fault or negligence and which is not foreseeable and not brought about at the instance of, the party claiming to be affected by such event and which has caused the non–performance or delay in performance. Such events may include, but are not restricted to, acts of the Purchaser/Consignee either in its sovereign or contractual capacity, wars or revolutions, hostility, acts of public enemy, civil commotion, sabotage, fires, floods, explosions, epidemics, quarantine restrictions, strikes excluding by its employees, lockouts excluding by its management, and freight embargoes. 26.3 If a Force Majeure situation arises, the supplier shall promptly notify the Purchaser/Consignee in writing of such conditions and the cause thereof within twenty-one days of occurrence of such event. Unless otherwise directed by the Purchaser/Consignee in writing, the supplier shall continue to perform its obligations under the contract as far as reasonably practical, and shall seek all reasonable alternative means for performance not prevented by the Force Majeure event. 26.4 If the performance in whole or in part or any obligation under this contract is prevented or delayed by any reason of Force Majeure for a period exceeding sixty days, either party may at its option terminate the contract without any financial repercussion on either side. 26.5 In case due to a Force Majeure event the Purchaser/Consignee is unable to fulfil its contractual commitment and responsibility, the Purchaser/Consignee will notify the supplier accordingly and subsequent actions taken on similar lines described in above sub-paragraphs. 23. Resolution of disputes 23.1 If dispute or difference of any kind shall arise between the Purchaser/Consignee and the supplier in connection with or relating to the contract, the parties shall make every effort to resolve the same amicably by mutual consultations. The jurisdiction for the settlement of disputes will be at the office of Medical Superintendent, ESIC Model Hospital, Nacharam, Hyderabad, Andhra Pradesh. . 23.2 If the parties fail to resolve their dispute or difference by such mutual consultation within twenty one days of its occurrence, then, unless otherwise provided in the SCC, either the Purchaser/Consignee or the supplier may give notice to the other party of its intention to commence arbitration, as hereinafter provided the applicable arbitration procedure will be as per the Arbitration and Conciliation Act, 1996 of India. In the case of a dispute or difference arising between the Purchaser/Consignee and a domestic Supplier relating to any matter arising out of or connected with the contract, such dispute or difference shall be referred to the sole arbitration of an officer, appointed to be the arbitrator by the Medical Superintendent, ESIC Model Hospital, Nacharam, Hyderabad, Andhra Pradesh. The award of the arbitrator shall be final and binding on the parties to the contract subject to the provision that the Arbitrator shall give reasoned award in case the value of claim in reference exceeds Rupees One Lac (Rs. 1,00,000/-) 23.3 Venue of Arbitration: The venue of arbitration shall be New Delhi, India. 24. Applicable Law The contract shall be governed by and interpreted in accordance with the laws of India for thetime being in force. Part II: Required Delivery Schedule: Within 90 days from date of opening of L/C for imported goods. The date of delivery will be the date of delivery at consignee site (Tenderers may quote earliest delivery period). If there are any domestic supplies, those shall be supplied on or before the imported items are delivered. Part III: Scope of Incidental Services: Installation & Commissioning, Supervision, Demonstration, Trial run and Training etc. shall be completed within 15 days of handing over the site of installation, complete in all respect by the
Page 15 of 43
consignee. The date of handing over of the site has to be intimated by the supplier to the purchaser. The delay on the part of the supplier to install and commission the equipment will attract the provisions as contained in the liquidated damage clause. Part IV: Required Terms of Delivery and Destination. a) For Indigenous goods or for imported goods if supplied from India: Delivery required at Consignee Site. Insurance (local transportation and storage) would be borne by the Supplier from warehouse to the consignee site for a period including 3 months beyond date of delivery. b) For Imported goods directly from abroad: The foreign tenderers are required to quote their rates on DDP at consignee’s site basis giving break-up of the price as per the Proforma prescribed in the Price Schedule. Custom clearance, handling, unloading & loading and transportation to the consignee’s site shall be the responsibility of the supplier/ Indian agent. Insurance (local transportation and storage) would be extended and borne by the Supplier from ware house to the consignee site for a period including 3 months beyond date of delivery. Qualification Criteria 01. The Tenderer must be a Manufacturer or its authorized Agent. 02. (a) The Manufacturer should have supplied and installed in last Five years from the date of Tender Opening, at least 100% of the quoted quantity of the similar equipment meeting major specification parameters which is functioning satisfactorily. The foreign Manufacturer satisfying the above criteria should also have supplied and installed in last Five years from the date of Tender Opening, at least 50% (or one No. where the schedule of requirement is one no.) of quoted quantity of similar model which is functioning satisfactorily anywhere outside the country of manufacture. 02. (b) The Tenderers quoting as authorized representative of the manufacturer meeting the above Criteria 02 (a) should have supplied and installed in last Five years from the date of Tender Opening, at least 50% (or one No. where the schedule of requirement is one no. ) of the quoted quantity of similar equipment which is functioning satisfactorily, anywhere in Indiaof the same manufacturer.
Page 16 of 43
TECHNICAL SPECIFICATIONS Human Anatomy
1. Electrically operated hand drill Universal hand drill; comprise saggital saw head piece, mini hand drill, transverse saw, triple drill guide130 angles as well as open gear hand machine drill with S.S. check and key. These are precision designed in line with defined safety standards and for cadaver use.
2. Hand Saw(S.S.)
For HRC, Blade materials reaches 52 degrees and teeth reaches 60 degree (+ or – 3)
Chrome treatement , antirust, smooth resulting in less friction
Eligant handles, ergonomic, Special teeth design, sharp at edges
Versatile assortments.
3. BAND SAW FOR SECTIONING BODY AND LIMBS
Manual Band Sawing Machine Technical Specifications:
- 100
Approx Weight in Kg 400
4. BRAIN KNIFE
Knives are of premium quality in cutting instruments sigment, high quality stainless steel with
heat –treat our blades.
Feauters:
Edge technology creats a blade i.e. sharper out of box, holds it’s edge longer and is easier to
resharpen, handle materials used are selected from variety of man made and natural materials
providing the best appereance and performance.
5. Specimen jar/Acrylic & Plastic tanks for storing soft and dissected parts Small, medium sizes starting from 200x125x125 mm to 250x250x250 mm or 360x150x100 .
6. Medical stool –revolving with back rest
The counter height medical stools with a stool height that can be adjusted for 21” to 31” by using
the hands- released pneumatic mechanism.
The stool with 5 star polished aluminium based and coloumn with 2 ” hooded casters , both the
14” diameter round and 16” square seats for constructed of 3” high density foam and
upholestered in choice of different vinyl colours .
Counter height
Adjustable back rest.
16” diameter square seat 21”-31” adjustable seat height.
325 LBS weight capacity.
Page 17 of 43
Medical stool for dissection hall and all practicable laboratories including anatomy dissection
hall.
7. Dissecting instruments set of 17
Student anatomy dissecting Kit
Ideal kit for variety of specimen dissections carries most widely used instruments
Dissection kit contents
Cartilage knife 2” blade
Scalpel with screw lock blade
Narrow blade scalpel 1.5”blade
Foreceps 4.5” with guide pin, medium points
Foreceps 4.5 ” with guide pin curve, find points
Disecting scissors, iris 4.5”
Probe and hook chrome
Dissecting scissors with 1.5 sharp and one point blent 5.5”
Teasing needle straight
Teasing needle bent
Ruler 6” plastic
Dissecting chain and hook chrome
Disscecting blow pipe 6”
Double fold vilnyl case
Toothed foreceps
8. Diamond pencils or glass marking pencils
9. Bones (disarticulated) sets – real human bones, lose bones;
10. Dissection Table-SS Standard Size:6”.1”X2”X3”
Is entirely made of S.S. (steel grade 1.4301), with a frame made of rugged torsion resistant S.S.
profiles and 4 S.S. swivel locking castors (125mm dia.). the table top has a depth of approx.
15mm sloping towards the drain. Large radii on all inside corners provided for easy cleaning. A
10 L container with bayonet lock, mounted beneat the down spout, is applied to a rack in the
base frame. An air tight compartment mounted beneath the table top serves for an odour free
storage of drapes. It features a stainless steel full extension drawer and a removable S.S. tray
provided with perforated plate and a removable lid.
11. Dissection Table-Half Standard Size: Same as above but of half standard size and
preferabally with wheels.
12. Embalming work station with embalming ,machine or cadever injector
* complete work station containing embalming trolley and embalming machine.
* Suited to equipment embalming machine
* Trolley made of complete SS manufactured with out rivets or bolts on the surface.
* Manual Ratchet system provided for trendelenburg position .
Page 18 of 43
* Embalming machine mounted on the under laying frame for complete system transportation.
*Embalming machine can be dismounted and used separately.
*Provided with heavy castors with easy movement with or without embalming machine.
* Embalming trolley approximate 60” length x28” width x 34” height.
* Embalming machine uses Specialized noise less pump for suction and delivery at preset
optimum pressure..
* Fluid delivery rate 101 ltrs/hr
* SS inner tank with fluid capacity provided.
*Complete SS outer body mounted provide.
* Complete SS outer body mounted on castors.
* Approx size of the EM- 24” length x19” width x 14.5”height
Embalming machine with its specialized noise less pump, provide suction and delivery at
optimum pressure with a fluid delivery rate of 10 litres/hr with salient features such as
*SS Inner tank to storesfluid capacity 10-15litr
Mounted on caators for easy movement and grips provided for lifting
IV stand fixed for mounting cannula tubing and mains cable
Mains on and in use indication provided
Complete stainless steel outer body / and /or
Cadeverous injector
For injecting formaldehyde solution in cadaeverous at much higher speed than normal
gravity process. Unit is fully covered and mounted on a portable trolley having 4 castor
wheels for easy movement. Unit consist of one air compressor fitted with half HP motor
which is connected with a stainless steel tank of 10 litrs capacity meant for storing and
injecting the solution. Tank is fitted with a safety valve, pressure gauze and rubber tubing
having provision for injection and supplied complete with electric cord , plug and suitable to
work on 220KV , 1PH 50HZ , A.C.supply.
13. Meat cutting machine for thin body sections ( trans &vertical) for gross anatomy
sectional study
Bone and meat cutting machine’ useful for specimen of big size in anatomy, fitted with large
moving table and extension table operator on 4 ball bearing rollers.
Specifications:
Size of cutting table 785x585 mm. approximate , total table travel 1245 mm approximate,
extension table 455x765 mm, size of wheel 455 mm approximate , height 1700 mm
approximate , the table is made of thick SS sheet with special heavy axles for easy and firm
movement . Supplier complete with one blade, stater, cord and plug.
Suitable to work on 220v , single page, 50HZ A.C.capacity.
14. Mortuary cooler with arrangement to keep 6 bodies
Mortuary cabinet – to store at least 6 Cadaverous/bodies
Page 19 of 43
Mortuary coolers are designed to be a reliable and durable part of hospital equipment. With
complete knock down construction it can be easily assembled at site
Temperature range: 2 to 8 degree Celsius
Hermetically closed hinged doors for low power consumption and high efficiency
Servo controlled voltage stabilizer (5KVA) with time delay for complete peace of mind in case of
power fluctuation.
Pre engineered poly urethane foam panels sand witched in high quality SS sheets with total
thickness of 60mm for excellent insulation. All stainless steel construction completely rust free;
vapor proof incandescent lamp mounted glows on door opening
Mortuary Carriage
Carriage is made of a three piece assembly which includes a stationary frame carriage and
upper carriage. The lower carriage and upper carriage assemblies ride on wheels and tracks
that allow easy telescopic action. The complete assembly is automatically locked when returned
to closed position.
Mortuary tray
One piece stainless steel tray (to accommodate a cadaver of Max. 7ft. length) with edge (16G)
and handles on both ends (12G)
Refrigeration System:
Heavy duty self contained, compact and unitary type with hermitically sealed compressors with
air cooled refrigeration system and energy efficient machines capable of operation at 230V,
50Hz, 1PH, Ac supply. Thermostat controlled
Security locks to prevent unintentional switch off.
Temperature performance in range 20C to 80C to ambient temperature of up to 400C
Current capacity: 6 – 15 amp; Refrigerant: R22
Refrigeration Capacity: at 400C at room temperature, 5000BTU/Hr
Control system: digital temperature Indicator – cum – controller with PT – 100 Sensors,
continuously monitors and displays the mortuary temperatures
Alarm audio – visual alarm in case of temperature variation beyond limit due to power failure or
any other reason.
Thermometer: dial type capillary thermometer
15. Portable LCD Projector with dedicated computer system
Portable LCD Projector
Computer system
Intel Dual core 2.5Ghz processor with 02 MB cache memory
Intel chipset G 31 motherboard (make will be gigabyte or asus)
1GB DDR2 667 Mhz RAM
250GB sata Seagate hard disk (7200RPM)
18.5” LCD
22X LG Double layer DVD Writer
ATX Cabinet (Black Silver) or (Red and Black)
Multimedia Key Board & Optical mouse.
Sound on board
AGP on Board
LAN on Board 16. Simple S.S Stretcher trolley for cadever transport
Page 20 of 43
Strong steel tubular frame work of trolley mounted on four 150 mm diameter swiveling castors. Removable stretcher top. Made of S.S./ Aluminium seat supported on tubular frame. Pre treated and epoxy powder coated over all approximate size 2030 mm Lx560 mm width x 820 height 17. Research Microscope
Binocular microscopes with PLAN objectives. Anti fungus finite optical systems; halogen or LED
light source options; feather touch co axial focusing mechanism; with digital camera attachment
and image processing software; upgradable to phase contrast, florescence, dark field and digital
microscopy; Advanced with Camera/LCD attachment.
18. Pre Prepared Histology slides Histology of the following Ithelium all types , connective tissue , cartilage –hyaline , elastic, fibrocartiredge etc, bone –CS, LS, Muscles-Skeletol, smooth, cardiac, nervous tissue- neuron nerve fibre, Sciatis and optic nerves , sympathetic spinal ganglia , blood vessel- large and medium size artery, large and medium size vein , Lymphoid tissue –Lymphnode, spllen, thymus, Palitine, tonsil, Skin-thin, thick, mammary gland- active, inactive placenta, umbilical cord, Respiratory system –Trachea , lung tissue, nervous system , excretory system, Retina endocrine system, Reproductive system, Digestive system. 19. Microtome,Sledge,large cutting
Sledge microtome / sliding microtome for cutting large blocks of paraffin and resin embedded
material for life microscopy. The knife holding clamps shall allow the knife to be opset to the
direction of cut, a major advantage when suctioning large, hard blocks. The microtome which is
very heavy for stability and not usually subject to vibration with a feed range of 0-20 microns.
20. Cabinet for slides(1000 wooden/plastic)
Wrap proof, break proof moulded plastic/ wooden boxes for storage of prepared microscopic
slides. Have slots to accomidate 1000 slides with lid /wooden with hinged lid, Slides are held in
number slots and there is a index inside the lid.
21. Incubator
1. Double walled chamber 2. Two doors inner plexi doors 3. Three side heating elements on three side of the equipment 4. Digital temperature controller cum indicator with forced air circulation fan 5. Inner size: 24”X 24” X36” approx. 6. No. of shelves: 03.
22. Paraffin Embedding bath(6 cup and 8sieves)
Double walled S.SS inner ,slide drying chamber at bottom, Copper cups and tubes with lids and
handle, temp. range:ambient +/- 5-65 degree centigrade works on 220V AC.
23. Hot Plates for Flattering Sections (Slide warming tablet) 18X12” (Approx.)
Rectangular or round Hot plate Cast Iron top 200mm, with Energy regulator Sizes: 250X400X150mm, digitally controlled (optional); S.S. Top; works on 220V AC
Page 21 of 43
24. Balance analytical
Standard features:
Easy to read Large back light GRAPHICAL LCD display with A.E.P.(Advanced Eye protection)(NEW)
Standard RS 232C Interface Ps/2 output
Hanger for Below Balance weighing
Fully automatic internal Calibration with built in weight
Complies GLP/GMP.
Dye cast aluminium design for long term stability and accurate results.
Various weighing units like, mg,ct.oz,dwt,mon,GN
User selectable Stability and filter level Spacious draft shield interior.
Technical data:
Capacity 220 gm: Readability 0.1mg: REPEATABILITY (+/-) 0.1mg; linearity (+/-)
0.2mg; PAN Size (mm/inch) 90Ǿ; response time: 03 sec, display Back light LCD
graphical display; calibration automatic external units of measure; G,mg, ct, GN,
mo, oz,dwt, T are range full operating; temperature 5deg. C to 40 deg.C.,
housing dimension (342.5mmX212mmX341mm - WDH)
25. COLOUR MARKERS:
Permanent marking pen
Permanent marker pen is an aluminium cigar type rigid tube with hemispherical rubber at one end, when pumped slightly compressed in towards a fine ball point for sharp and fine marking . Basically using a slotted template for marking datum line when testing dimensional stability (shrinkage) to washing and processing on fabrics.
Product
Codes
Yellow Red Orange Black Blue Green White
Plastic
tip
Metal tip
26. Balance ear hanger
Capacity: 6 Kilos, Sensitivity 1/5gram, plastic scale
Hanger Type circular weighing scales – 1
Dial type analog display; light weight aluminium die cast body; un breakable convex lens;
matching body and lens ring; sturdy durable and maintenance free;
Or
Spring Type: In graduated tubular aluminium with zero adjustment, provided with top
suspension loop and hook, with dual scale in metric and newton range. 5000grms with precision
of 100 grms.
27. Distilled water still with stainless steel , wall mountable model
Manesty type water still: made of all stainless steel; output 4Lt./hr approx.; work on 220VAC; the
condenser can be opened easily for periodic cleaning., designed to provide pyrogen free
distilled water easily. Complete unit made of stainless steel. The lid perfectly rest and get sealed
inside the collar on the head of the tank which avoids loss of steam and jumping of lid., easy
wall mounting.
Page 22 of 43
28.Laboratory refrigerator:
Specifically designed and are suitable for research laboratories, blood banks
applications and across other laboratories working with critical elements. The laboratory
refrigerator controls temperature varying from 2deg. C to 8deg. C. the unit shall be
vertical model constructed of double walls high quality powder coated exterior mild
cabinet. The laboratory refrigerator shall be insulated with high density CFC free Poly
urethane foam. The inner chamber is made of S.S. 304 grade. With built in micro
controller based temperature indicator cum controller having audio visual alarms. Door
locking system for improved security with magnetic door gasket. Air cooled hermetically
sealed compressor. Technical data
Capacity Internal (cm) External
265 ltr 58X50X97 70X62X158
29.All Quartz Distillation Apparatus (05 Ltr Capacity)
With 05 Ltr/Hr, Metallic stand and other accessories.
30. X – Ray Viewing lobby
4 panel side by side X – Ray View box illuminator
Standard features: 2 lamps (F15IT8/D) per panel, roller gravity film holding systems, durable
steel construction, thin 3” profile, chip
Resistenat hospital white finish, continuous bottom film ledge, even vue reflective system, UL
and cUL listed, Centralized cluster on/off switching; FAS – film activated switching, MS – Master
Switch, HGP – Hospital Grade Plug Specs: surface wall mount 4 panel side by side 56”X17”
viewing area overall Dimensions: 56” L 21” H3 3/8 D. illumination: 2000cd/m2. Approximate
weight 84lbs.
31. Dissection Microscope – Stereo Type
Stereo dissecting microscope – magnification 20X. objective fixed 2X achromatic
parfocal 80mm working distance. Coated lens eyepieces WF 10X paired field of view 5.5mm.
Fine focus by rack and pinion motion. Adjustable head in height on pole stand. Round glass
(mirror) 82mm stage with black and white matted plate for plate for field contrast. Thermocol
packing with instruction manual, dust cover. Optional: WF 15X eye pieces.
32.Hot air oven
Hot air oven for drying slides (45 degree Celsius) 18”X18”X18” (Approx.)
Lab model with three side heating elements
Construction: with double walled construction. Inner chamber made of Aluminium or stainless
steel sheet. Outer chamber is made of mild steel sheet, finished with powder coated paint. The
gap between the walls is filled up with special grade glass wool for proper insulation to avoid
heat losses. Inner chamber has ribs for placing the shelves at convenient levels. Supplied with 2
or 3 removable shelves. It is fitted with heavy hinges with a ball catcher, spring loaded door
closing device. Door is duly insulated.
Page 23 of 43
Elements: heating elements are made of high quality nickel/chrome plated nichrome wire which
are put inside beads and placed at the bottom and in both the side ribs for uniform temperature
all over the work space.
Temperature Control: temperature is controlled by imported capillary type thermostat from 50°C
to 250°C +/- 1°C. Temperature control knob is graduated in centigrade degrees. Ovens are
supplied without thermometer.
Ventilation: air ventilators are placed near the top of the both sides to remove hot gasses and
fumes if any.
Control Panel: comprising of switch to ON/OFF the power, switch to select high or low rates of
heating, thermostat control knob and indicators for mains and thermostats. Supplied with cord
and plug. Suitable to operate on 220 volts, 1ph, 50Hz, AC Supply.
Optional Accessories: Air circulating pan, digital display temp indicator, digital display temp
controller cum indicator in lieu of thermostat., microprocessor based PID temp. controller cum
indicator in lieu of thermostat., L shaped thermometer (Mercury) or straight type. Timer
Size of inner chamber WXHXD = 455X455X455mm, No. shelves=2.
33.LAMINATED PHOTOGRAPHS-CHART OF VARIOUS HIOSTOLOGY SLIDES
Ithelium all types , connective tissue , cartilage –hyaline , elastic, fibrocartiredge etc, bone –CS, LS, Muscles-Skeletol, smooth, cardiac, nervous tissue- neuron nerve fibre, Sciatis and optic nerves , sympathetic spinal ganglia , blood vessel- large and medium size artery, large and medium size vein , Lymphoid tissue –Lymphnode, spllen, thymus, Palitine, tonsil, Skin-thin, thick, mammary gland- active, inactive placenta, umbilical cord, Respiratory system –Trachea , lung tissue, nervous system , excretory system, Retina endocrine system, Reproductive system, Digestive system.
34. Skeletons articulated – real human bones –
35.Mobile or portable pedestal operating- Surgical light
Mobile surgical light features:
Dome:01 No;700mm(normal0:Dom Diameter 50mm (nominal) 500mm+/-50mm, spring arm
stroke 750 mm +/_50mm, Field size 150-200mm,1600mm(Nominal), action radius
1500mm(nominal),175000 LUX(Max),light output 130000 Lux (Max) ,color temperature;4200+/-
300 degree Kelvin;halogen bulb no,7 no.s.12 V,50 W each/24V 70W 4
no.s.12V,50Weach/24V70W;low voltage unit with CVT 230V AC+/-10%230V AC +/-10%;Input
supply :50Hz+/-2%,Hieght adjustment of Dome:36”
36. Monocular Microscope (Compound Microscope)
a. Stage movement (vertical) by co-axial coarse/fine roller guide (rack and pinion type). Coarse movement stroke: 20mm tension on the right. Fine focusing knob (graduated).
b. Quadruple revolving nose piece (fixed) c. Plane stage 120X132mm. d. With mechanical stage right hand. e. Abbe condenser N.A 1.25 (Oil Immersion), with aperture iris diaphragm.
Vertical adjustment range : 10mm f. Blue filter
Page 24 of 43
g. Built in 6V 20W illuminator base. h. 8cc immersion oil. i. Dust cover j. Mirror unit (Plano concave) k. Monocular observation tube l. Power cord m. Lamp 6V 20W halogen lamp (x2) n. Objectives
i. Achromatic 4x M (anti fungus) ii. Achromatic 10x M (anti fungus) iii. Achromatic 40x M (anti fungus) iv. Achromatic 100x M (anti fungus)
o. Eye piece : two no. 10x, 18mm (anti fungus)
37.Semi Automatic Rotary Microtome
Advanced microtome Modular system with exceptional precision Best suited for research and routine work in biological, medical or histology lab; guaranteed over extension protection and sliding – clutch anti – locking system in the coarse advance. ; Highest precision of sections. The semi automatic unit shall offer Automatic advance for trimming; motorized advance/return of specimen; specimen advance automatic in two speeds. The equipment is supplied complete with Cassette holder; knife holder base; standard knife holder Object orientation unit; section waste tray; microtome knife 15cm Technical data
Ranges of thickness 0.5µm to 99 µm
Increments of minimum 0.5µm
1 µm step from 1 µm to 99 µm electronically adjustable
Horizontal specimen advance 28mm
Vertical stroke 60mm
Specimen size Up to 30mmX30mm
Specimen orientation X and Y Axis 8°, Z Axis 360°
Specimen advance automatic In 2 speeds
Advance for trimming 1 – 99 µm adjustable
Electrical data 230Volts, 50cycles single phase AC
38.Rack of Anatomy Museum Specimens-Museum Racks with study table Facilities-
Special Designs
39.Museum Jars:
Specify various sizes with catalogue assorted.
40.Charts-Illustrative: Laminated photographs etc
41. 3D models in organic system and complete set of Embryology:
General Embryology and developmental anatomy
Page 25 of 43
Production to embryology and human development, oogenesis, Ovarian cycle , Male
reproductive system and spermatogenesis,Fertilisation and Implantation, Bilaminar Germ disc,
Trilaminar Gern disc,Intra embryonic mesoderm,folding of the embryo, formation of placenta,
Circulation of placenta, Fetal membrane, twinning, basic teratology, details blood vessels 4th
and 6th aortic arches derivatives,musculo-skeletal system integument system and nervous
system.Review of special embryology:Gastro intestinal system, Urinary system; Genital
system;Spleen;Diapharagm;Heart;4thand 6th aortic arch derivatives;Respiratory system;Face
;Palate;Tongue;Visual neural tube and their derivatives.
Unbreakable made out of fiber glass
BIO-CHEMISTRY:
42.Urinometer
Glass urinometer The Urinometer is indented to measure the specific gravity of urine
samples.The specific gravity of urine varies with the amount of solids in solution and is also
effected by fluid intake versus fluid;loss through skin,lungs & bowls.Urinometer is a hydrometer
with scale graduations corresponding to the range of specific gravity of urine.A hydrometer is
essentially a weighted float with a graduated stem of small diameter that sinks in the test liquid
to a depth proportional to the specific gravity of the liquid.
43.Ryles tube
44.Thermometer
Digital thermometer ,digital thermometer resolution 0,1degree centigrade range 50-150 degree
centigrade supplied with a temperature probe with cable for digital thermometer support to
150degree centigrade.
45.Wet & dry thermometer
Comprising two - 10 to +50 degree centigrade thermometer fitted on scale .One thermometer
bulb is covered with muslin ,which is kept moist by being connected to a reservoir of water
.Mounted on a painted ,wodden base.With humidity and temperature conversion chart.
46.Cork –borer set
Digital- digital stop watch.Digital stop watch is perfect for any laboratory applications .The large
LED display,high resolution enhances the functionality in several of situation .These are
available in two ranges as per specification.Range 1:99:59:59Hrs :minutes:second.Resolution
:1sec (for range one)minute:sec:milli sec.range 2:99:59:99hrs:minu:sec.Resolution :10millisec
(for range 2).Display :6digit LED display.
47.Stop watch digital
Digital- digital stop watch.Digital stop watch is perfect for any laboratory applications .The large
LED display,high resolution enhances the functionality in several of situation .These are
available in two ranges as per specification.Range 1:99:59:59Hrs :minutes:second.Resolution
:1sec (for range one)minute:sec:milli sec.range 2:99:59:99hrs:minu:sec.Resolution :10millisec
(for range 2).Display :6digit LED display.Alarm :buzzer after set time.
Page 26 of 43
48.Bottle dispenser Indian
0.5-5ml,1-10ml,2.5-25ml,5-50ml,10-100ml(5types)high quality. 49. Vortex Mixer Test tube mixer; the unit is meant for quick and thorough mixing of liquids in test tubes, small flasks or bottles. The mixer consists of an enamel finished housing containing the motor with the motor with an eccentric drive to a rubber buffer on the top. The tube is held against the vibrating buffer and the intensity of agitation controlled by varying the position in which the test tube is held. The thyristorized speed controller enables step less adjustment of degree of oscillations. 50. Magnetic stirrer with Hot Plate The magnetic stirrer with hotplate but shall have additional stainless steel hot plate. PMDC motor gives higher torque even at lower speeds and maintains speed stability despite viscosity or volume changes. Accurate step less speed control allows smooth vibration up to 1200rpm. Heating energy is controlled by energy regulator. 51. Vacuum pump
35 lit. capacity; single stage; oil sealed air cooled V – Belt driven and mounted on a base plate
with belt guard etc. with motor 220VAC single phase.
52.Chromatographic chamber
Chromatography – cabinet Rescholar’s chromatography cabinets, which are made of teak
wood with glass on four sides and on top. The internal surface is coated with wax in order to
ensure resistance to solvent and other chemicals.
53. Distilled water with stainless steel ,wall mountable model
Manesty type water still :made of stainless steel ,output 4lit per hour approx,work on
220VAC,the condenser can be opened easily for periodic cleaning designed to provide pyrogen
free distilled water easily,complete unit made of stainless steel.The lid perfectly rest and get
sealed inside the collar on the head of the tank which avoids loss of steam and jumping of
lid,easy wall mounting.
54 . Laboratory dessicator large size
8” dia soda glass ; □ Glass dessicator, Imported make: Sizes, 240 mm, 300mm or □ Plastic
Dessicator: Unbreakable Polycarbonate Lid & Polypropylene bottom with PP sieves
55. Laboratory dessicator small size
6” dia soda glass ; Glass dessicator, Imported make: Sizes, 100 mm, 150mm or Plastic
Dessicator: Unbreakable Polycarbonate Lid & Polypropylene bottom with PP sieves
56. UV lamp with fittings
UV Lamps to meet the requirements of our clients. These lamps are effective in eliminating oxides, micro organisms and other contaminants in water. The lamps are manufactured in advanced production units using quality components. Features: high turbulence; non wetting surface; high reliability low maintenance.
Page 27 of 43
57.Spirit lamp (stainless steel) made of stainless steel die pressed capacity 125ml
58.Fume cupboard
Floor model – with SS table top, side glass panels, back side should be made of acid and
alkali resistant material, transparent front door. It should be complete with blower, gas cock,
sink, DOL starter LT/LK, rain protection cowl, PVC electing, working space – approx.
120X60X60cm.
59.Water bath Rectangular: Thermostatic Control/; Boiling water baths with lids having 8 – 12 holes
Temperature range from ambient to 95°C. Thermostatic control with an accuracy of +/- 1C. Double walled with inner wall of stainless steel and outer of MS powder coated, with Lids of
SS. The unit is provided with immersion type heaters top work on 220VAC. The unit is supplied with indicating lamps, main chord and Plug. Size of Inner chamber – approx. 355X405X100mm; 1 5kw
60.Auto clave Vertical model-Electrically operated
Bioler, lid and flange are all made of thick gauge stainless steel and argon arc welded for high
safety.Electrically heated .A neoprene rubber gasket is provided on the flanges ,which helps the
lid to seat properly there by eliminating steam loss.A pedal lifting arrangement is provided for
easy operation.The unit is provided with water drainage arrangement .The unit is provided with
pressure gauge,steam release cock and safety valve.The unit is tested at 25psi by hydrollic
pressure .The operating pressure is 15psi.The thick MS stand is provided and supplied with
main chord and plug.Size of the inner chamber 550x 350mm
61. Balance Open Pan type
Open pan triple beam 610gms or electronic/digital single pan.
62. Balance semi Micro Single pan mechanical type; new generation semi – micro balance for every day laboratory use. Capacity/ readability: 42g/0.01mg-210g/0.1mg one touch calibration easy access to door system, winct – windows communication tools, automatic adjustable environment setting.
63. Balance Micro (Electronic)
Micro analytical balances 0.0001 to 220g. motorized internal calibration; ISO GLP
compliance (optional); multiple weighing units; standard bidirectional RS 232 interface; poly
function: % weighing, counting, fill mode, GSM back light LCD Display; density determination
kit (optional)
64.Constant temperature Water Bath
(17”X10”X9”); or serological water bath is double walled filled with high grade glass wool
insulation between the two chambers. Outer chamber of serological water bath is made of mild
steel with power coating and inner chamber is made of stainless steel. 7.5 Litres. Cap, Inner
chamber size [WXLXD]- approx. 25X20X15cmc; excluding heater power in [W]1000.
65. Laboratory Incubator Electric with Thermostat
Temperature range above ambient to 65°C, thermostatic control with a sensitivity of +/-1C.
heating elements are provided at the bottom of the chamber. Double walled with inner chamber
of SS. Outer made of MS with powder coating. The gap is filled with glass wool form insulation.
Page 28 of 43
The unit comes with wire mesh shelves, indicating lamp, main chord and plug. Size:
approx.60X60X60cm inner chamber made of SS; Accessories to be provided: compulsory a. fan
for circulation of air inside the chamber, b. digital temperature controller cum indicator.
66. Hot air oven
Bottom heated - temperature range 250°C. Thermostatic controlled with an accuracy of +/- 1 °C. Double walled inside made of SS and outer with MS duly powder coated finish. The gap is filled with glass wool for insulation. Heaters are provided at the bottom. The unit is supplied with wire mesh shelves and it works at 220VAC. The unit is supplied with indicating lamp, main chord and plug; size of the SS inner chamber 605X605X605mm. accessories: (compulsory for higher sizes)a. digital temperature controller cum indicator : 2400.00b. fan for air circulation; 1400.00 67.Calorimeter
Photoelectric calorimeter with 8 filter digital
Digital calorimeter – highly stable and accurate ideal clinical instruments for blood and chemical
analysis. Models available ME 953 C 5 filter ME 954C8 filter ME 944 C 8 filter with battery
option. Range: 400nm to 700nm filters 5 high standard filters, Accuracy: +/-0.02O.D., Out Put
Optional, Density 0 to 1.99, display 2.5 digit LED display, detector selenium photo cell, light
source 6.2V 0.3 Amp. Tungsten filament Lamp, Min. volume 1ml., power 230V+/- 10% 50Hz
Ac., size (LXBXH) 225X230X150mm, weight: 4Kg.(Approx), Accessories Test Tubes 5 Nos,
Light Source Bulb, Dust Cover, Instruction Manual.
68. Flame photometer
a. Up to four elements should be measurable with single aspiration. b. Automatic filter selection (Narrow band interface) c. Automatic settings of electronic systems d. Curve fittings for non linear range(up to minimum 05 standards) e. Calibration should be storable in memory f. Provision for re-standardization g. Record should be storable pertaining to date and time analysis h. Provision for saved set up to minimize operation steps. i. Measurement results should be recalled later on with display and print out (330 Max).
Element Serum Urine Bio – Fluids
Na 100-200meq//1: 100dil 0-250meq//1: 100dil All the four elements up
to 250meq// with 1:
200dil
K 0-10meq//1: 100dil 0-100meq//1: 200dil
LI 0-2meq//1:10dil
Ca 0-10meq//1:2dil
j. Filters (10nm Typical): Na and K (must) Li and Ca (optional) k. Reproducibility: should be atleast +/-2%f.s. l. Aspiration Time: should be (5 sec + Avg. time) per element + 4 sec. m. Air compressor: with built- in air regulator and air filter deliver stable and moisture / oil
free air supply n. Fuel gas: LPG o. Power supply: should be 230VAC+/-10%, 50Hz.
69.All glass (quartz)double distillation apparatus
Apparatus 5litr capacity double stage 5litr per hour with metallic stand and other acc
70. High speed centrifuge
Laboratory equipment centrifuge machine high speed – heavy duty Sturdy MS Body, well painted finish, with maximum speed of 6000RPM at 10/12 tube of 15ml total square body, with lid lock manual type, speed control by analogue know, digital display of timer, timer time 0-60 minutes speed display is digital, speed setting with help of knob, auto off if lid is open, lid breaking system provided, power consumption 500Watt, power requirement 220V and 50 to 60Hz, weight approx. 15Kgs, total noiseless operation, non vibration, complete with head and power lead.
Page 29 of 43
71.pH meter
Digital Electronic (Table/ hand held model); comprehensive range of PH meters which includes digital PH meter, Hand held PH meter, PH testing meter etc. PH meters are made up using best quality parts and equipments. PH Range: 0-14PH. Mill Volt range: 0 to 1999mv. Resolution: 0.01ph, 1mv. Repeatability: +/- 0.01PH +/- 1mV. Accuracy: 0.01 PH+/- 1 digit, 1mV +/- 1 digit. Temperature compensation: 0 to 100deg C. operating temperature: 10 Deg C to 50 Deg C. display: 3.5 digit LED display. Supplied accessories: Electrode, Stand, dust cover and instruction manual.
72.Tissue homogenizer complete set
The tissue – tearor is a rotor /stator type tissue homogenizer which can rapidly homogenize, disperse and emulsify samples in 0.2 – 1000ml of liquid. During operation the suspended material is drawn in to the core of the homogenizer by a rotor turning up to 35000rpm. The material is repeatedly cycled through six narrow slits in the stator where it is rapidly sheared and disintegrated by high frequency mechanical action. Complete homogenization of tissues (muscle, liver, breast tissue etc.) is usually achieved in 10-30seconds. Little if any heat is produced during the process; the tissue - tearer shall come in complete - that is both motor and probe (aka, generator dispersing tool) are included in one price only. Features….. Used for mixing, emulsification, shredding or chopping. Practical answer for small samples. Easy to hold and light weight for one hand operation. Can also be stand mounted. Autoclavable stainless steel probes. Insert to aggressive solutions, Inert to aggressive solutions, all probes are interchangeable probes.and are easily removed for clean up; high speed motor. Speed control from 5000 to 35000rpm.
73. Samplers or auto pipettes Different volume range each 06 nos. the features are as follows: fixed, reduced thumb stress, consistent sample loading, compatible with most types of tips. Soft force tip loading and ejection. One hand tip ejection. Leak free sealing of tip. Manifold can rotate 360° for easy right or left hand operation; Volume: 5µl, 10 µl, 20 µl, 50 µl, 100 µl, 500 µl, 1000 µl. 74. Monocular Microscope With built illumination lamp. Eye piece 10X, objectives 5X, 10X, 45X and 100X oil immersion lens, built in mechanical stage with fine and coarse adjustment.
75.Binocular Microscope-Research microscope
Binocular microscopes with PLAN objectives. Anti fungus finite optical systems; halogen or LED light source options; feather touch co axial focusing mechanism; with digital camera attachment and image processing software; upgradable to phase contrast, florescence, dark field and digital microscopy; Advanced with Camera/LCD attachment.
76. Refrigerator 350 litres with freezer compartment
77.Paper electrophoresis apparatus
Vertical model with small 3 strips vertical large 06 strips mini power pack for the above 02 models . Electrophoresis apparatus paper strip model: electrophoresis apparatus shall consist of a transparent Perspex sheet cabinet 40X23.75X11. 25cm to accommodate 4 strips of 1.5” X 12” with glass cover provided with safety inter look switch. The cabinet is fitted with leveling screws. The apparatus shall be supplied with power supply for supply from 0-400v and 0.100 milli ampere in 1 milli ampere division resp. this unit consists of a millimeter and voltmeter, polarity reversing switch and connection cable to work on 220v, 50cycles ac mains.
78.Spectrophotometer
Page 30 of 43
Digital spectrophotometer: imported U.V. Visible type, wavelength range: 190 – 1100nm Optical system, dual beam wavelength. Accuracy : +/- 0.3nm, baseline flatness: +/-0.002 A detector: Dual silicon photodiode
HUMAN PHYSIOLOGY
79.Haemocytometer inclusive of Neubauer counting chamer,RBC,WBC pipettes
contained in a box
With heavy cover slip, improved neubauer counting chamber specialized microscopic slide.
Inside cell of chamber, and area of 9 Sq.mm(3x3) Sq.mm divided into 9 squares of 01 mm side
by means of triple lines. The central small square is further divided by triple lines 5x5 =25
smaller squares each with side 1/5 of a mm each of the square is further divided into 4x4 =16
smallest squares with side equal to one twentieth of a mm. Thus dimension of a individual cell of
0.05x0.05x0.0025 mm2.
Gap between cover ‘0.1 mm, slilp grid area.
Pipettes: RBC and WBC pipettes.
Accessories: Rubber Suckers for RBC&WBC pipettes
Cover slips: 22x25 mm one box
Wodden box: inside dimensions approx. 100x175x30 mm
Accessories: additional two RBC & WBC Pipettes each with every neubauer chamber.
Essential: ISO certified /BIS marked.
80.Sahli (Sahli - Adams) hemoglobinometer or hemometer Consists of comparator, hemoglobin tube, hemoglobin pipette, stirrer, Pasteur pipette etc., Technical specifications: Measuring range – 40 – 360g/litre As a photometer the device measures optical density of a solution with precision not worse than 1%. The total error of definition of concentration of a hemoglobin (In view of an error of a method, and also errors of dosing of a blood and solutions), obtained at comparative medical tests, does not exceed 2% The volume of liquid for photometry must be not less than 1ml. optical length of a cuvette or cylindric test tube – 10+/-0.1mm. dimensions: 178x127x43mm.
81.All glass (quartz)double distillation apparatus
Apparatus 5litr capacity double stage 5litr per hour with metallic stand and other acc
82.Monocular Microscope With built illumination lamp. Eye piece 10X, objectives 5X, 10X, 45X and 100X oil immersion lens, built in mechanical stage with fine and coarse adjustment. 83.Incubator
1. Double walled chamber 2. Two doors inner plexi doors 3. Three side heating elements on three side of the equipment 4. Digital temperature controller cum indicator with forced air circulation fan 5. Inner size: 24”X 24” X36” approx. 6. No. of shelves: 03.
Clinical Physiology 84.Stethography
a. Kymographs b. Mary’s tambour, Corrugated rubber tube c. Connecting rubber tube
Page 31 of 43
85.Compact CPR training mannequins
Economical CPR mannequins constructed of soft realistic vinyl plastic over poly
urethane foam for a human feel. Features include: a longer torsofor realistic abdominal
thrusts, realistic head tilt and chin lift for opening airway, can easily be manipulated to
realistically stimulate airway obstruction or choking situations, and a user friendly lung or
airway design that eliminates cleaning. Includes three mouth/nose pieces and three
disposable lung/airway systems. Dimensions: 28”X18”X10”. Nylon carry bag and kneeling
pads included with warranty.
86.Apparatus for continous passive motion CPM is used to treat joints of the lower limb after an onjury ,disease or following surgery . Based on a concept originated by SALTER IN 1970, this device has varied applications namely treatment of intra articular fractures ,septic arthritis,ligaments tendon healing and also following total replacement to ensure a sufficient range of motion. To prevent stiffening ,the jouint hae to be moved continuosly ahich results in the following. Minimize swelling and pain after operation Ensures faster recovery and shorted hospital stay Prevents extra articular contractures and adhensions. Ext/Flex angle indicator at knee position Compact and elegant construction Electronic controls enable all adjustments of angle to be made on the front panel Smooth and silent movement Digital timer alarm Patient safety for stopping and reversing the motion. Specifications
Treatment time 0-99 minutes
Reset time 1 to 5seconds
Angle Extension 0
Power 230v/A.C./50 HZ, 75 VA
87. Dynamometer Especially suitable for use in rehabilitation centers/physiology labs; Real time mode: immediately shows the patients current strength Peak/Max Mode: shows the maximum strength of a patient’s grip Average Mode: calculates the average strength from two grips Counting mode: counts the numbers of presses which exceed a previously defined strength limit; integrated AUTO – OFF function after 1 minute to preserve the batteries; as part of a rehabilitation program, this permits medical staff to monitor the fitness of the patients hands and carry out controlled training exchangeable springs facilitate fast switching of the capacity (Additional spring sets for 20Kg and 40Kg are included with delivery); safe, comfortable use thanks to non slip rubber grips
Stable case for safe, easy transport and for storage of the additional spring sets as standard,
WXDXH: 350X265X85mm
88. Sterilizer electric (Medium Size)
Construction of stainless steel. For team sterilization/disinfection of surgical materials/instruments. With handles for lid and base. Available in various sizes, custom sizes can be made on request. 300X150X100mm
89. Water distillation apparatus
Manestry type water still: made of s.s.; out put 4 litr per hour approx; work on 220 VAC; the
condenser can be opened easily for periodic cleaning , designed to provide pyrogen free
distilled water easily. Complete unit made of stainless steel. The lid perfectly rest and get sealed
inside the collar on the head of the tank which avoids loss of steam and jumping of lid., easy
wall mounting.
Page 32 of 43
90. Wrigght”s peak flow meter
Lower range mini wright PFM(30-40ppm0 with sterilizable mouth piece. 91.Mosso”s ergography Mosso’s ergographic with metronome and weights. Ergographic contain the advantages of feauters of bubios and moss’s ergographic with weight set. 92. Audiometry
Audiometry & tympanometry in one instrument; special Audiometry window; MPANL (maximum
permissible ambient noise level) specified internationally by standard institutes like OSHA and
ANSI for proper acoustic treatment.
93.Clinical Examination couches Adjustable head end – hydraulic type. Metal 16Gauge with good insulation. Must have 03 drawers and 03 boxes. The bed should have high quality sponge with rexin cover. Must have stand for BP apparatus. 94. Bicycle ergometer
Work Load Range: 10 – 600Watt Independent Rpm: 20 – 130rpm Work Load range Dependent RPM Lap Time: 9h 59min 59sec Load Steps : 1 – 99 Watt Time Steps : 1 – 99 Min Load Programs: Manual 1 Load/Step PWC 170, 150, 130 HR Steady State Safety Protection Automatic Load: Heart rate Reduction: Blood pressure Blood Pressure D Acoustic signal: ECG Alarm Signal Manual : By Stop Button Check: Calibration Dynamic Static Adjustments (Height): 83cm – 110cm Saddle: 68cm – 108mm Handle bars: free rotation Accuracy of load: 2% or 3 Watt Input/output External Control: RS - 232 Inputs: Analogue control Start signal Heart rate Blood pressure s Blood pressure D ECG Alarm Outputs: work load Pedaling Speed Step Marker Power supply: 110 – 240V, 50 – 60Hz Power consumption: 100VA Safety Standard: class 1, CE Dimensions (cm): Base plate 79X48 Weight: approx 46Kg
Page 33 of 43
95. Instrument Trolley SS; frame work of SS tubes mounted on four 50mm dia swiveling castors. There are two stainless steel shelves with three side railings on top shelf only in these instrument trolleys. Pre treated and epoxy powder coated. Overall approximate size : 680mm (L)X450mm (W)X820mm (H). 96. Centrifuge, High speed with telcometer etc. Laboratory equipment centrifuge machine high speed – heavy duty Sturdy MS Body, well painted finish, with maximum speed of 6000RPM at 10/12 tube of 15ml total square body, with lid lock manual type, speed control by analogue know, digital display of timer, timer time 0-60 minutes speed display is digital, speed setting with help of knob, auto off if lid is open, lid breaking system provided, power consumption 500Watt, power requirement 220V and 50 to 60Hz, weight approx. 15Kgs, total noiseless operation, non vibration, complete with head and power lead. 97. Calorimeter
Photoelectric calorimeter with 8 filter digital
Digital calorimeter – highly stable and accurate ideal clinical instruments for blood and chemical
analysis. Models available ME 953 C 5 filter ME 954C8 filter ME 944 C 8 filter with battery
option. Range: 400nm to 700nm filters 5 high standard filters, Accuracy: +/-0.02O.D., Out Put
Optional, Density 0 to 1.99, display 2.5 digit LED display, detector selenium photo cell, light
source 6.2V 0.3 Amp. Tungsten filament Lamp, Min. volume 1ml., power 230V+/- 10% 50Hz
Ac., size (LXBXH) 225X230X150mm, weight: 4Kg.(Approx), Accessories Test Tubes 5 Nos,
Light Source Bulb, Dust Cover, Instruction Manual.
98. pH meter
Digital Electronic (Table/ hand held model); comprehensive range of PH meters which includes digital PH meter, Hand held PH meter, PH testing meter etc. PH meters are made up using best quality parts and equipments. PH Range: 0-14PH. Mill Volt range: 0 to 1999mv. Resolution: 0.01ph, 1mv. Repeatability: +/- 0.01PH +/- 1mV. Accuracy: 0.01 PH+/- 1 digit, 1mV +/- 1 digit. Temperature compensation: 0 to 100deg C. operating temperature: 10 Deg C to 50 Deg C. display: 3.5 digit LED display. Supplied accessories: Electrode, Stand, dust cover and instruction manual.
99. Electronic Muscle stimulator
Research model: Muscle Stimulator
Compact Solid-state Microprocessor Controlled unit, with digital timer and intensity display is useful for functional paralysis resulting from traumatic neurosis, Hysterical of Neuropraxia, Flaccid Paralysis, Spastic Paralysis, Cardio-vascular disorders and Muscle Strain etc. The Therapeutic Muscle Stimulator has Galvanic, Interrupted Galvanic, Faradic and Surge Faradic currents. The unit shall be housed with ABS molded cabinet. Salient Features Microprocessor controlled Pulse durations: 03,1,10,30,100,300ms Pulse Repetitive Freq.:0.3,1,3 seconds Intensity variations: 0 130 Volts Technical details Weight:1.6Kg.Height:139.7mm ,Width:266.7mm Depth:190.5mm Voltage: AC 100 260 Protection Class-I Complies with IEC 601-1 Option for Built-in rechargeable battery.
100. Balance analytical
Standard features:
Easy to read Large back light GRAPHICAL LCD display with A.E.P.(Advanced Eye protection)(NEW)
Standard RS 232C Interface Ps/2 output
Hanger for Below Balance weighing
Fully automatic internal Calibration with built in weight
Complies GLP/GMP.
Dye cast aluminium design for long term stability and accurate results.
Various weighing units like, mg,ct.oz,dwt,mon,GN
User selectable Stability and filter level Spacious draft shield interior.
Page 34 of 43
Technical data:
Capacity 220 gm: Readability 0.1mg: REPEATABILITY (+/-) 0.1mg; linearity (+/-)
0.2mg; PAN Size (mm/inch) 90Ǿ; response time: 03 sec, display Back light LCD
graphical display; calibration automatic external units of measure; G,mg, ct, GN,
mo, oz,dwt, T are range full operating; temperature 5deg. C to 40 deg.C.,
housing dimension (342.5mmX212mmX341mm - WDH)
101.Laboratory refrigerator:
Specifically designed and are suitable for research laboratories, blood banks
applications and across other laboratories working with critical elements. The laboratory
refrigerator controls temperature varying from 2deg. C to 8deg. C. the unit shall be
vertical model constructed of double walls high quality powder coated exterior mild
cabinet. The laboratory refrigerator shall be insulated with high density CFC free Poly
urethane foam. The inner chamber is made of S.S. 304 grade. With built in micro
controller based temperature indicator cum controller having audio visual alarms. Door
locking system for improved security with magnetic door gasket. Air cooled hermetically
sealed compressor.
Technical data
Capacity Internal (cm) External
265 ltr 58X50X97 70X62X158
102. Recording spirometer-Benedict”s Roth Spirometer- Apparatus Spirometer has a 4 speed electrical recording unit with gravity writing in. valves are easily accesable , soda lime chamber with screw collection in the centre chamber drain to all the tubes and container. Sampling cork for connecting the patient to spirometer or atmosphere . The unit is fitted on portable frame , complete with valves, tube, mouth piece, nose clip, ink writing well and 50 charts. 103.ECG Single channel
a) Digital one channel ECG machine b) Simultaneous 12 leads acquisition c) Multiple operation mode (Manual/auto/ref. lead) d) LCD to display operation status and wave – form e) The wave form is displaying synchronously on the LCD with 195X65 dots f) AC/DC power, built in rechargeable Ni-MH battery g) High resolution thermal printing array system h) High frequency response reach to 150Hz i) Capable of printing continuous one channel trace and annotations including lead
marks and such parameters as sensitivity, paper speed, and filter operation status. j) High resolution digital inhibits baseline k) One touch operation able to enhance efficiency and relieve operation strain l) Concept of floating input circuit meets IEC safety standard m) Visual status due to light indicated touch keys n) Rechargeable battery supporting more than 50 patient examinations o) Under the automatic mode, pressing key mode continuously can keep recording
when abnormal lead is found. p) Safety level corresponds to class I, type CF
104. ECG Machine –multi channel
High resolution thermal array printer; 12 channel print out format 5 inch 320X240lcd to display
setting menu and 12 channel ECG wave form automatic measurement and interpretation of
ECG paper size: 210mmX20m (roll type) 210X140mmX20m (z-fold type)
Page 35 of 43
105. EEG Machine Recorder – portable
EEG 100B amplifier module with CAP 100 EEG electrode cap/with electrodes and cardiac jelly;
EEG (Electroencephalograph)
Features: A device being used by neurologists
Light weight and compact amplifier; USB 2.0 interface/Ethernet interface; synchronized high
resolution MPEG-4 video; integrated photic stimulator; integrated impedance check for
electrode connectivity; unlimited nos. of montages; unlimited continuous recording along with
video (optional)
106. Physiograph
Single channel , electric recorder and electrical stimulator with
1. Main console- chart dry , pen recording system; Main amplifier: coupler housing and 2. Couplers – bio potential coupler; electrocardiogram (EKG) and stain gaze coupler ; 3. Stimulator.
107.Experimental physiology Demonstration set including Sherrington starrling kymograph (preferably electrically driven) myograph stand, indecorum, simple key short circulating key, pohl’s commutator, vibrating, interrupter, muscle through, muscle liver, muscle grip of femor clamp, hook and weight set, heart liver, frog board for dissection, enamel tray for above frog board cork line with boss – head – low voltage unit, for tapping 2 and 4 bolts for stimulation., at each seat-as required. Note: time makers can also be made available at each seat along with a low voltage unit. Electronic stimulators, a student type can be used instead of low voltage units. This will also dispense with the need for induction coil interrupter
1. central low voltage unit (low volts 3 – 6 volts) – battery or rectifier unit and a step down transformer. 2. the keys – simple key & short circuiting key 3. induction coil (Du – Bois Raymond indecorum) 4. electric kymograph (“ Drum”)/Sherrington starrling kymograph 5. frog muscle chamber (Luca’s Moist chamber; muscle through) 6. writing lever 7. starrling heart liver 8. isometric lever 9. vibrating reed 10. variable interrupter 11. time marking – tuning fork (100 or 256Hz); spring time marker; electromagnetic time marker. 12. stimulating electrodes 13. student stimulator 14. self ink thermo – paper (like ECG paper) other accessories 1. langedorff’s apparatus 2. dales organ bath.
108. Spirometry System
Simple spirometer/ students spirometer/vitalograph: – spirometer – packed with features for the
expert user; colour touch – screen operation; accurate fleisch pneumatachograph; integral clear,
fast printer,; on screen visualization of volume /time and flow/volume curves.
109 . Computerized PFT with interpretation facililties
Pulmonary function test department is equipped with PC based equipment capable of giving
data in tabular form for 33 parameters (FVC,SVC, and MVV), pre and post medication option
available for comparison
Page 36 of 43
Features: complete digital processing; user friendly alpha numeric LCD display; easy to operate;
soft touch key pad; audio indication with each function; elaborate prediction equations; optional
interpretation facility; fast and noise free printing; well formatted report; 14 measurement
parameters
110. Mechanical Respirator 1. Drinker’s tank respirator (Iron lung) 2. Sahlinjacket model, Brag-Paul pulsator 3. foldable canvas stretcher for Eve’s rocking method. 111.Electromyogram
EMG amplifier module/EL 503 shielded snap electrodes or 3 surface electrode/stimulating and
recording electrode, electronic stimulator, a recording system of cathode ray oscilloscope
(CRO)/ bio potential coupler.
112. Multichannel Polygraph –computerized.
4/8/16 channel data acquisition and analysis system ( MP 100WSP with acq. Knowledge soft ware.) Accessories; STM 100 A; EMG 100 b; STM ISO; EL 300 electrode pairs; Lead 100 electrode leads; LEAD 100 S leads; EL 503 electrode; GSR 100 b electro- Dermal activity amplifier module; TSD 103A electrode- dermal activity electrode gel; Measuring tape.
Page 37 of 43
Annexure-I
CHECKLIST Name of Tenderer: Name of Manufacturer:
Sr.No. Activity Yes/
No/N
A
Page No. In
TED
Remark
s
01 Have you enclosed EMD of required amount for the
quoted schedules?
02 Have you enclosed clause-by-clause technical
compliance statement for the quoted goods visà-vis
the Technical specifications?
03 In case of Technical deviations in the
compliance statement, have you identified and
marked the deviations?
04 Have you kept validity of 120 days from the Techno
Commercial Tender Opening date as per the TE
document?
05 Have you enclosed duly filled Tender Form as per
format in ?
06 Have you enclosed Power of Attorney/
Authorisation in favour of the signatory?
07 Have you submitted manufacturer’s
authorization as per Section?
08 Have you submitted the certificate of
incorporation?
09 In case of Indian Tenderer, have you furnished
Income Tax Account No. as allotted by the Income
Tax Department of Government of India?
10 In case of Foreign Tenderer, have you
furnished Income Tax Account No. of your Indian
Agent as allotted by the Income Tax Department of
Government of India?
11 Have you intimated the name and full address of your
Banker (s) along with your Account Number
12 Have you furnished Annual Report (Balance Sheet
and Profit & Loss Account) for last three years prior to
the date of Tender opening?
13 Have you submitted the Quality Control
Requirements as per Proforma given the TE
document?
14 Have you accepted delivery period as per TE
document?
Page 38 of 43
15 Have you accepted the terms of delivery as per‘ DDP
at consignee site basis’?
16 Have you accepted the warranty/CMC as per TE
document?
17 Have you accepted all terms and conditions of TE
document?
18 Have you fully accepted payment terms as per TE
document?
19 Have you submitted satisfactory end user
performance certificate
20 Have you submitted copy of the order(s)
against the above end user certificate (s)?
1. All pages of the Tender should be page numbered and indexed. 2. The Tenderer may go through the checklist and ensure that all the documents/confirmations listed above are enclosed in the tender and no column is left blank. If any column is not applicable, it may be filled up as NA. 3. It is the responsibility of tendered to go through the TE document to ensure furnishing all required documents in addition to above, if any.
(Signature with date) (Full name, designation & address of the person
duly authorised sign on behalf of theTenderer)
For and on behalf of (Name, address and stamp of the tendering firm)
Page 39 of 43
Annexure-II MANUFACTURER’S AUTHORISATION FORM To, Medical Superintendent ESIC Model Hospital, Nacharam, Hyderabad-500076 Andhra Pradesh Dear Sir, Ref. Your TE document No ____________, dated _____________ We, ___________________________________ who are proven and reputable manufacturers of___________________________(name and description of the goods offered in the tender) having factories at___________________________________________________________, hereby authorise Messrs______________________________(name and address of the agent) to submit a tender, process the same further and enter into a contract with you against your requirement as contained in the above referred TE documents for the above goods manufactured by us. We further confirm that no supplier or firm or individual other than Messrs. ________________________ (name and address of the above agent) is authorised to submit a tender, process the same further and enter into a contract with you against your requirement as contained in the above referred TE documents for the above goods manufactured by us. We also hereby extend our full warranty, CMC as applicable as per clause 15 of the General Conditions of Contract, read with modification, if any, in the Special Conditions of Contract for the goods and services offered for supply by the above firm against this TE document.
Yours faithfully, [Signature with date, name and designation]
for and on behalf of Messrs___________________________ [Name & address of the manufacturers]
Note: 1. This letter of authorisation should be on the letterhead of the manufacturing firm and should be signed by a person competent and having the power of attorney to legally bind the manufacturer. 2. Original letter may be sent.
Page 40 of 43
Annexure-III
TENDER FORM Date__________
To, Medical Superintendent ESIC Model Hospital, Nacharam, Hyderabad-500076 Andhra Pradesh Ref. Your TE document No. _________dated ___________ We, the undersigned have examined the above mentioned TE document, including amendment/corrigendum No. __________, dated ________ (if any), the receipt of which is hereby confirmed. We now offer to supply and deliver___________ (Description of goods and services) in conformity with your above referred document. If our tender is accepted, we undertake to supply the goods and perform the services as mentioned above, in accordance with the delivery schedule specified in the List of Requirements. We further confirm that, if our tender is accepted, we shall provide you with a performance security of required amount in an acceptable form in terms of GCC clause 5, read with modification, if any, in Section - V – “Special Conditions of Contract”, for due performance of the contract. We agree to keep our tender valid for acceptance as required in the GIT clause 20, read with modification, if any in Section - III – “Special Instructions to Tenderers” or for subsequently extended period, if any, agreed to by us. We also accordingly confirm to abide by this tender up to the aforesaid period and this tender may be accepted any time before the expiry of the aforesaid period. We further confirm that, until a formal contract is executed, this tender read with your written acceptance thereof within the aforesaid period shall constitute a binding contract between us. We further understand that you are not bound to accept the lowest or any tender you may receive against your above-referred tender enquiry. We confirm that we do not stand deregistered/banned/blacklisted by any Govt. Authorities. We confirm that we fully agree to the terms and conditions specified in above mentioned TE document, including amendment/ corrigendum if any
(Signature with date) (Name and designation) Duly authorised to sign tender for and on behalf of
Page 41 of 43
ANNEXURE-IV PRICE SCHEDULE A) PRICE SCHEDULE FOR DOMESTIC GOODS OR GOODS OF FOREIGN ORIGIN LOCATED WITHIN INDIAN ORIGIN
Total Tender price in Rupees: _____________________________________________________________________________
In words: _____________________________________________________________________________________
Note: -
1. If there is a discrepancy between the unit price and total price THE UNIT PRICE shall prevail.
The charges for Annual CMC after the warranty shall be quoted separately as per Section-XI – Price Schedule C
1 2 3 4 5
Price per unit (Rs.)
6
Sl.No Brief
Description
of Goods (with
make & model)
Country
of
Origin
Quantity Total price (at
consignee
site) basis
Ex - factory/
Ex-ware house/ Ex-show
room/ Off -the shelf
(a)
Excise duty(if
any )(% age
&value)
(b)
Sales
tax/Vat(if any)
% age &value
(c)
Transportatio
n,
loading/unloa
ding &
incidental
cost till
consignee's
site
(d)
Insurance
charges for
the period
including 3
months
beyond the
date of
delivery
(e)
Incidental
services(inclu
ding
installation
and
Commissioni
ng,
supervision,d
emonstration
and training)
at the
consignee's
site
(f)
Unit price (at
Consignee
site)basis
(g)=a+b+c+d
+e+f
(g)
Page 42 of 43
Name________________________
Business Address________________________
Place: ___________________________ Signature of Tenderer_______________________
Date: _________________________ Seal of the Tenderer________________________
B) PRICE SCHEDULE FOR COMPREHENSIVE MAINTENANCE CONTRACT AFTER WARRANTY PERIOD
1 2 3 4 5
Item SI.No. Brief Description of the goods Quantity(No.s) Comprehensive Maintenance
Contact Cost for each unit year
wise*
Total Comprehensive Maintenance
Contract Cost for 5 (or as specified
) Years[3X(4a+4b+4c+4d+4e)]
1st 2nd 3rd 4th 5th
a b c d e
*After completion of warranty period
NOTE:-
4. In case of discrepancy between unit price and total prices,the unit price shall prevail 5. The cost of comprehensive Maintenance Contract (CMC) which includes preventive maintenance including testing and calibration as per technical/service/operational manual
and labour, after satisfactory completion of warranty period quoted for next 5 (or as specified) years on yearly basis for complete equipment and Turnkey(if any). 6. The cost of CMC may be quoted along with taxes applicable on the date of Tender Opening. The taxes to be paid extra,to be specifically stated. In the absence of any such
stipulation,the price will be taken inclusive of such taxes and no claim for the same will be entertained later. 7. Cost of CMC will be added for Ranking/Evaluation/purpose. 8. The payment of CMC will be made as per clause 21.1(D) 9. The uptime warranty will be 98% on 24 Hours X 7daysX365 days basis or As stated in technical specification of the TE Document. 10. All Software updates should be provided free of cost during CMC period. 11. The stipulations in technical specification will supersede above provisions. 12. The supplier shall keep sufficient stock of spares required during comprehensive Maintenance Contract (CMC). Incase the spares are required to be imported,it would be
responsibility of the supplier to import and get them custom cleared and pay all necessary duties Name________________________
Page 43 of 43
Business Address________________________
Place: ___________________________ Signature of Tenderer_______________________
Date: _________________________ Seal of the Tenderer________________________