Temporizator Start Stop

K2579

ILLUSTRATED ASSEMBLY MANUAL H2579IP-2

Total solder points: 62 Difficulty level: beginner 1 2 3 4 5 advanced

Small size timer provides up to

60 minutes delay.

UNIVERSAL START/STOP TIMER

Specifications

Relay output with switchover contact. Power supply : 12VDC regulated. Typical active current : 55mA. Relay output : 2A/240V max. Dimensions : 35x70mm / 1.37x2.75"'

H2579IP'1_rev3.pubpage 1

Tuesday, May 22, 2012 15:06

VELLEMAN NV Legen Heirweg 33

9890 Gavere Belgium Europe

www.velleman.be www.velleman-kit.com


Tuesday, May 22, 2012 15:06

3

The K2579 is a basic timer with relay output for time intervals of up to 15 minutes. Set the desired delay with the trimmer. The maximum delay can easily be lengthened and the timer can be stopped and restarted at any time. Features Start / stop push buttons included. LED status indicator. Timing adjustable from a few seconds to 15 minutes, extendable to 60 minutes. Relay output with switchover contact. Specifications : Power supply : 12VDC regulated. Typical idle current : 20mA. Typical active current : 55mA. Relay output : 2A/240V max. Dimensions : 35x70mm / 1.37x2.75"'

Features & Specifications


Tuesday, May 22, 2012 15:06

Assembly hints

1. Assembly (Skipping this can lead to troubles ! ) Ok, so we have your attention. These hints will help you to make this project successful. Read them carefully. 1.1 Make sure you have the right tools:

A good quality soldering iron (25-40W) with a small tip. Wipe it often on a wet sponge or cloth, to keep it clean; then apply solder to the tip, to give it a wet look. This is called ‘thinning’ and will protect the tip,

and enables you to make good connections. When solder rolls off the tip, it needs cleaning. Thin raisin-core solder. Do not use any flux or grease. A diagonal cutter to trim excess wires. To avoid injury when cutting excess leads, hold the lead so they cannot fly towards the eyes. Needle nose pliers, for bending leads, or to hold components in place. Small blade and Phillips screwdrivers. A basic range is fine.

For some projects, a basic multi-meter is required, or might be handy

1.2 Assembly Hints :

Make sure the skill level matches your experience, to avoid disappointments. Follow the instructions carefully. Read and understand the entire step before you perform each operation. Perform the assembly in the correct order as stated in this manual Position all parts on the PCB (Printed Circuit Board) as shown on the drawings. Values on the circuit diagram are subject to changes, the values in this assembly guide are correct* Use the check-boxes to mark your progress. Please read the included information on safety and customer service * Typographical inaccuracies excluded. Always look for possible last minute manual updates, indicated as ‘NOTE’ on a separate leaflet.

0.000

1.3 Soldering Hints :

1- Mount the component against the PCB surface and carefully solder the leads

2- Make sure the solder joints are cone-shaped and shiny 3- Trim excess leads as close as possible to the solder joint


Tuesday, May 22, 2012 15:06

DO NOT BLINDLY FOLLOW THE ORDER OF THE COMPONENTS ONTO THE TAPE. ALWAYS CHECK THEIR VALUE ON THE PARTS LIST!

REMOVE THEM FROM THE TAPE ONE AT A TIME !


Tuesday, May 22, 2012 15:06

6

R1 : 1K (1 - 0 - 2 - B) R2 : 10K (1 - 0 - 3 - B) R3 : 4K7 (4 - 7 - 2 - B) R4 : 1K (1 - 0 - 2 - B) R5 : 10K (1 - 0 - 3 - B) R6 : 4K7 (4 - 7 - 2 - B) R7 : 1K (1 - 0 - 2 - B)

2. Resistor R...

Construction

D1 : 1N4148

1. Diode. Watch the polarity !

D...CATHODE

RV1 : 2M2

5. Trim potentiometer

IC : 8p.

3. IC socket. Check the position of the notch!

C1 : 100nF

4. Capacitor

C...

T1 : BC547B

6. Transistor

C2 : 100µF

7. Electrolytic Capacitor. Watch the polarity !

LD1 : 5mm RED

8. LED. Check the polarity!

LD...

COLOR = 2...5

CATHODE

C...


Tuesday, May 22, 2012 15:06

7

Construction

SW1 : START SW2 : STOP

9. Push buttons

RY : VR15M121C

10. Relay

RY...

IC : NE555

11. IC. Check the position of the notch!


Tuesday, May 22, 2012 15:06

8

12. Connection example

Connection example

220nF/400V

100E/1WA B or C

Snubber network*

*see hook-up and use

NC

NO

AB

CCOM12V DC

300 mA


Tuesday, May 22, 2012 15:06

9

Hook-up and use

Connect the unit with a 12VDC regulated power supply as shown in the example. Turn the trimmer all the way counterclockwise. Push the START button. The relay will be activated momentarily. The position of the trimmer determines the ON-time. Turn it clockwise to increase the ON-time. Increase the value of C2 for an even longer activation duration. The unit can be stopped at any time by pressing the STOP button. The START and STOP buttons can be mounted in a remote location. Make sure to use screened cable,

avoid outside interference and keep the distance between the switches and the PCB as short as possible. The timer is equipped with a relay output that is galvanically separated from the rest of the circuit for extra

safety. The connection example lists the function of the pins of the relay contacts. If the relay is used to switch important inductive loads, such as electric motors or transformers, it may be

necessary to install a snubber network across the relay contacts to avoid excessive contact wear. Ensure that the power supply of the circuit is sufficiently HF decoupled. Noise impulses entring

trough the power supply may start and stop the circuit unnecessarily.

13. Hook-up and use


Tuesday, May 22, 2012 15:06

10

10. PCB layout.

PCB

14. PCB layout.


Tuesday, May 22, 2012 15:06

11

CTL 5

GN

D1

OUT 3RS

T4

THR6 TRIG2

DISC7 VC

C8

IC1

NE555

R64K7

R41K

R34K7

R1

1K

R210K

RV12M2

C2100µ

T1BC547

R5

10K

RYVR15M211C

D11N4148

SW2 SW1

A

B

C

POWER +12V

GND

GND

GND

LD1LED

R71K

C1100n

GND

15. Diagram

Diagram


Tuesday, May 22, 2012 15:06

5 4 1 0 3 2 9 3 1 1 3 8 4Modifications and typographical errors reserved - © Velleman nv. H2579P - 2012 - ED2 (rev.3)

Learn how to connect your computer with the outside world, master the USB communication with tutorial examples. Play with LED indicators and learn how to drive LCDisplays.

This board with different signals will teach you how to use an oscilloscope. Optimized instructions for use of our HPS140 oscilloscope. YouTube demo movies.

Fun solar powered projects. Learn all about solar energy.

EXPERIMENT KIT SOLAR ENERGY EDUKIT SCOPE

TUTOR BOARD USB

Learn how to solder, build different exciting projects. Includes spare components and demo boards.

STARTER BOX SOLDER EDUCATIVE

The EDU01 basic experiment kit is the first step into the world of modern electronics. Build your own circuits in a fun, safe and educative way.

EDUCATIVE STARTERBOX SOLDERLESS

03

02

01

06

05

Enter the world of microcontroller programming, easy step by step instructions. Includes programmer and test board.

TUTOR KIT PICTM 10


Tuesday, May 22, 2012 15:06

Temporizator Start Stop

Documents

Transcript of Temporizator Start Stop