TELESCOPING GAUGE - A.C.T.Equipmentactequipment.com/pdf/MTI-Spring2014-ACT.pdf · 2014. 5. 2. ·...
Transcript of TELESCOPING GAUGE - A.C.T.Equipmentactequipment.com/pdf/MTI-Spring2014-ACT.pdf · 2014. 5. 2. ·...
2
TELESCOPING GAUGE
• Spring loaded plunger expands within the bore allowing determination of the internal diameter (or groove width)
DIAL DEPTH GAUGE
Range Stroke Order No. Grad. List Price SPECIAL
0-8” 1” 7218S .001” $307.00 $276.30
0-200mm 10mm 7211 0.01mm $293.00 $263.70
• Wide probing range is available with the supplied extension rods
QUANTUMIKE MICROMETER
SAVERZONE
SUPER
• Range: 1-2”/25.4-50.8mm• Resolution: .00005”/0.001mm• With SPC output• Coolant proof IP65 protection• Faster measurement with 2mm per
revolution instead of standard 0.5mm
ORDER NO. 293-181 SUPER SAVER PRICE $317.90Reg. List $374.00
ID-U DIGIMATIC INDICATOR
SAVE 15%OFF REG. LIST
• Range: 0-1”/0-25.4mm• Resolution: .0005”/0.01mm• ABSOLUTE encoder technology• With SPC output• Slim design with flat back• ANSI/AGD type - steam dia. 3/8”
ORDER NO. 575-123 SUPER SAVER PRICE $185.60Reg. List $232.00 SAVE
20%OFF REG. LIST
SUPER SAVER PRICES FOR THESE ITEMS ARE VALID FOR MAY 2014 ONLY
THICKNESS GAUGES
Range Order No.
Grad. Remarks List Price SPECIAL
0-10mm 7360 0.01mm For tube thickness $160.00 $144.00
0-1” 7322S .001” Deep throat, ceramic spindle/anvil $205.00 $184.50
0-10mm 7301 0.01mm Standard, ceramic spindle/anvil $142.00 $127.80
155-904 set
Range Order No. List Price SPECIAL
.75-1.25” 155-123 $36.00 $32.40
1.25-2.125” 155-124 $39.00 $35.10
3.5-6” 155-126 $51.00 $45.90
.50-6” (Set of 5) 155-904 $197.00 $177.30
.315-2.125” (Set of 4) 155-907 $138.00 $124.20
DIGIMATIC DEPTH MICROMETER
• Interchangeable rod type• Ratchet stop• SPC data output
ORDER NO. 329-350-10SPECIAL $673.20Reg. List $748.00
• Range: 0-6”/0-152.4mm• Resolution: .00005”/0.001mm• 6 rods
7360
MAYMAYONLY
3
LEADING EDGE TECHNOLOGY FROM MITUTOYONOW AVAILABLE AT YOUR MITUTOYO DISTRIBUTOR
New ratchet-thimble improves
operation and repeatability
AOS - New electromagnetic inductive sensor repels dirt, oil and water ensuring 100% reliability
Function Lock system has been added
Anti-slipfinish Extended
battery life
New 293 Series high-performance micrometers achieve world's highest level with advanced functionality and reliability.
Digimatic Coolant-Proof Micrometers
Top-of-the-line Digital Caliper operates battery-free. ABSOLUTE encoder eliminates repetitive zero-setting, with no restriction on operating speed.
ABSOLUTE Solar Digital Calipers
IP67 protection assures waterproof reliability
Display is impact resistant for improved visibility and
protectionMinimum illumination required is 60 lux
(uncharged) or 50 lux (charged)
ABS (absolute) scale requires no origin setting after power-on and has
unlimited response speed
ABSOLUTE Solar Digimatic Indicator
ABS Digimatic Caliper CD-AX/APX This new series of cost-effective digimatic calipers is derived from 30 years of accumulated Mitutoyo technologies. Equipped with electromagnetic induction type absolute encoder and AOS (Advanced Onsite Sensor) used in top-of-the-line ABS coolant-proof calipers.
Eco-friendly operation eliminates the hassle of battery replacement
Operates under minimum light conditions of 40 lux - lower than the level of a warehouse!
Large reserve of power allows extended use under minimum light conditions
World's first solar-powered digimatic indicator.
AOS - New electromagnetic inductive sensor repels dirt,
oil and water ensuring 100% reliability
ABS (absolute) scale requires no origin setting after power-on and has
unlimited response speed
Smooth, stable and comfortable slider operation due to the latest machining
technology
Celebrating 80 yearsMitutoyo, a global corporation with a presence in more than 80 countries, started from humble beginnings in 1934 in Japan. The journey was long and hard to reach the point where the company became recognized as the world’s leading manufacturer of dimensional measuring equipment, a position it has held for many years now. Today, many internationally renowned companies depend on Mitutoyo products and services to ensure consistent and high quality in their manufacturing operations, as do many thousands of other firms, both large and small.
Part of the reason for this success is that Mitutoyo seeks to be more than just a supplier of high-quality measuring equipment, but more like a valued partner of its custom-ers in their drive for successful manufacturing operations. Mitutoyo’s service to customers is renowned as being the best among metrology vendors, and with good reason – specialist technical personnel operating from strategically placed sites across the world are always ready to offer advice and assistance, especially in times of stress when the value of excellent support is truly measured and ap-preciated.
One thing we know for sure about our customers, both actual and potential, is that they are all looking for the best value available in measurement products, with first-class backup support services. In short, something that can only be provided by an established vendor with a proven record of commitment to their local market. After all, when the success of your company depends in large part on reliable, traceable measurement to national standards, with the service and supply backup of strong group resources, there really is no other choice.
An important factor is that Mitutoyo is a private company and so is unencumbered by shareholders looking for short-term profits, and therefore the company has always been able to pursue research and development programs that, although time and investment intensive, have offered the best chance of leading to long-term results of lasting benefit to industry, and therefore to society in general.
Mitutoyo Canada has been active in the Canadian market for over 40 years as a vibrant part of the Mitutoyo Group, operating from two M3 solution centers across the coun-try. The newly renovated corporate headquarters is located in Mississauga, Ontario with a state-of-the-art solution center, service base, parts and repair center, training and education classrooms as well as the main sales and admin-istrative support functions.
4
SAVER
OUTSIDE MICROMETERS
Range Order No. Graduation List Price SPECIAL
0-1” 103-260 .0001” $115.00 $103.50
1-2” 103-262 .0001” $133.00 $119.70
6-7” 103-183 .001” $194.00 $174.60
7-8” 103-184 .001” $210.00 $189.00
8-9” 103-223 .0001” $255.00 $229.50
9-10” 103-224 .0001” $275.00 $247.50
• Hammertone, baked enamel finish
• Ratchet stop• With a standard bar (except
0-1” model)
OUTSIDE MICROMETER SET
Range Order No. Graduation StemDia. / Style / Face List Price SPECIAL
0 - 6.5mm 148-201 0.01mm Ultra-small type 6mm / Plain / Flat $60.00 $54.00
0 - .5” 148-811 .001” Small size .375” / Plain / Spherical $68.00 $61.20
0 - 1” 153-207 .001” Non-rotating spindle type .5” / Plain / Flat (carbide tip) $145.00 $130.50
148-201
MICROMETER HEADS
• Range: 0 - 6”• Graduation: .001”• 6 gauge set with
5 micrometer standards
• Supplied in wooden storage box
Order No. List Price SPECIAL
103-904-10 $828.00 $745.20
153-207
BLADE MICROMETERS
• Anvil and spindle have a blade for measuring the groove diameter of shafts, keyways and other hard-to-reach areas
• Ratchet stop for constant force
• With a standard bar (except 0-1” model)
Range Order No. Graduation List Price SPECIAL
0-1” 122-125 .0001” $285.00 $256.50
1-2” 122-126 .0001” $312.00 $280.80
148-811
Range Order No. Graduation List Price SPECIAL
0-1” 115-253 .0001” $134.00 $120.60
SPHERICAL FACE MICROMETER
• For measuring wall thicknesses• Ratchet stop• Spherical anvil and spherical spindle
5
DIAL CALIPER
SAVERZONE
SUPER
• Range: 0-12”• Graduation: .001”• .1” range per revolution• Measures OD, ID, depth and steps
ORDER NO. 505-677SUPER SAVER PRICE $259.50Reg. List $346.00
DIAL INDICATOR
SAVE 25%OFF REG. LIST
• Range: 10mm• Graduation: 0.01mm• Range per rev: 1mm• Dial Reading: 0-100• Stem dia. 8mm (ISO/JIS type)
ORDER NO. 2046S SUPER SAVER PRICE $76.50Reg. List $102.00
SUPER SAVER PRICES FOR THESE ITEMS ARE VALID FOR JUNE 2014 ONLY
OUTSIDE MICROMETER SET
Range Order No. Graduation List Price SPECIAL
0 - 6” 104-137 .001” $448.00 $403.20
12 - 18” 104-201 .001” $843.00 $758.70
• Graduation: .001”• Anvils and Standards included• Ratchet stop• Wide measuring range with
interchangeable anvils
INSIDE MICROMETERS
Range OrderNo.
Mic. Head travel List Price SPECIAL
2-8” 141-208(with 3 rods) .5” $187.00 $168.30
25-32mm 141-001 7mm $84.00 $75.60
1-2” 141-102 .25” $173.00 $155.70
INSIDE MICROMETER
• Wide range of ID measurements with interchangeable rods
• Graduation .001”
SAVE 25%OFF REG. LIST
141-208
Range Order No. Graduation List Price SPECIAL
.2-1.2” 145-193 .001” $217.00 $195.30
1-2” 145-194 .001” $247.00 $222.30
• Caliper type jaws• Locking clamp for
positive locking of spindle
ORDER NO. 156-105-10SPECIAL $58.50Reg. List $65.00
• Fixed angle micrometer stand• For micrometer ranges 0-1”
and 1-2”/0-25 and 25-50mm
MICROMETER STAND
JUNEJUNEONLY
6
MICROMETER HEAD
SAVERZONE
SUPER
• Digit counter for easy reading of spindle movement
• Carbide tipped measuring face• Ratchet stop for constant force• Range: 0-25mm• Resolution: 0.01mm• 10mm Stem dia.
ORDER NO. 250-301SUPER SAVER PRICE $141.60Reg. List $177.00
DIGIMATIC HEIGHT GAUGE
SAVE 20%
• Range: 0-18”/0-450mm• Switchable Resolution: .0005”,
.0002”/0.01, 0.005mm• SPC data output• Carbide tipped scriber• Coarse/fine feed swithcing• Two preset reference heights
ORDER NO. 192-631-10SUPER SAVER PRICE $1,405.60Reg. List $1,757.00
SUPER SAVER PRICES FOR THESE ITEMS ARE VALID FOR JULY 2014 ONLY
SAVE 20%OFF REG. LIST
STEEL RULES
THICKNESS GAUGES
• Straight blades, 13mm width
• Blade length 100mm• 13 leaves
Order No. Range List Price SPECIAL
184-305S 0.05-1mm $38.00 $34.20
184-307S 0.03-0.5mm $38.00 $34.20
Full-Flexible Rules (thickness 1/64")
Order No. Size Graduations Width List Price SPECIAL
182-202 6”(16R) 1/32 1/64 1/50 1/100th 1/2” $16.00 $14.40
182-203 6”(5R) 1/32 1/64 1/10 1/100th 1/2” $16.00 $14.40
182-204 6”(3R) 1/32 1/64 1/10 1/50th 1/2” $16.00 $14.40
182-208 6” x 150mm 1/10 1/50 1mm 0.5mm 1/2” $24.00 $21.60
182-222 12”(16R) 1/32 1/64 1/50 1/100th 1/2” $31.00 $27.90
182-224 12”(3R) 1/32 1/64 1/10 1/50th 1/2” $31.00 $27.90
182-226 12” x 300mm 1/50 1/100 1mm 0.5mm 1/2” $43.00 $38.70
182-242 18”(16R) 1/32 1/64 1/50 1/100th 3/4” $49.00 $44.10
182-262 24”(16R) 1/32 1/64 1/50 1/100th 3/4” $93.00 $83.70Wide Rigid Rules (thickness 3/64")
182-101 6”(4R) 1/8 1/16 1/32 1/64th 3/4” $17.00 $15.30
182-103 6”(5R) 1/32 1/64 1/10 1/100th 3/4” $17.00 $15.30
182-111 150mm 1mm 0.5mm 1mm 0.5mm 19mm $17.00 $15.30
182-131 300mm 1mm 0.5mm 1mm 0.5mm 25mm $35.00 $31.50
182-143 18”(5R) 1/32 1/64 1/10 1/100th 13/16” $42.00 $37.80
182-145 18"x450mm 1/32 1/64 1mm 0.5mm 13/16” $42.00 $37.80
RADIUS GAUGE
• Composition of leaves: 16 pairs 17/64 x 1/2” by 1/64ths
• With locking clamp
Order No. Range List Price SPECIAL
186-102 17/64 - 1/2” $46.00 $41.40
SCRIBER
• Tungsten carbide tip• Length 6.75”
ORDER NO. 985-101SPECIAL $29.70Reg. List $33.00
JULYJULYONLY
OPTIONAL ACCESSORIES List SPECIAL 905338 SPC Cable 40” / 1m $46.30 $41.67905409 SPC Cable 80” / 2m $51.00 $45.90
7
BORE GAUGES
Range Order No. Remarks List Price SPECIAL
10-18.5mm 511-201 For small holes $260.00 $234.00
1.4-2.5” 511-732 Standard type $291.00 $261.90
50-150mm 511-404 For blind holes $492.00 $442.80
• Without dial gauge• With interchangeable anvils and spacers
BORE GAUGES WITH DIAL INDICATOR
511-732
Range Order No. Resolution List Price SPECIAL
.5”/12.7mm 543-267B .0001”/0.001mm $563.00 $506.70
• Digimatic indicator exclusively designed for ID measurement
• Minimum value holding function for easy detection of hole diameter
• ABSOLUTE encoder technology• ANSI/AGD type - stem dia 3/8”
OPTIONAL ACCESSORIES List SPECIAL 905338 SPC Cable 40” / 1m $46.30 $41.67905409 SPC Cable 80” / 2m $51.00 $45.90
Range Order No. Remarks Dial Gauge List Price SPECIAL
.24-.4” 511-212 For small holes
2923SB-10 Graduation .0001” $646.00 $581.40
6.5-10” 511-745Standard type
2922SB Graduation .0005” $607.00 $546.30
100-160mm 511-724 2109SB-10
Graduation 0.001mm $586.00 $527.40
• With dial gauge• With Interchangeable anvils and spacers
BOREMATIC - ABSOLUTE DIGIMATIC SNAP GAUGES
• TiN coated measuring contact points• 330o rotatable display• GO/NG judgment• ABSOLUTE encoder technology• SPC data output• Optional extension rods• Resolution: .00005”/0.001mm
Range(in/mm)
Order No.
List Price SPECIAL
1.0-1.225.4-30.48 568-467 $1,943 $1343.70
1.2-1.630.48-40.64 568-468 $1,630 $1467.00
1.6-2.040.64-50.8 568-469 $1,630 $1467.70
2.0-2.550.8-63.5 568-470 $1,747 $1572.30
Range(in/mm) Order No. List Price SPECIAL
.275-.5”6.985-12.7 568-987-10 $5,057 $4551.30
3-4”/76.2-101.6mm 568-991-10 $4,576 $4118.40
• TiN coated measuring contact points
• 330o rotatable display• GO/NG judgment• ABSOLUTE encoder
technology• SPC data output• Optional extension rods• Resolution:
.00005”/0.001mm
BOREMATIC SETS
OPTIONAL ACCESSORIES List SPECIAL 905338 SPC Cable 40” / 1m $46.30 $41.67905409 SPC Cable 80” / 2m $51.00 $45.90
TUBULAR INSIDE MICROMETERS
Range Order No. Graduation Mic Head
Travel List Price SPECIAL
4-52” 139-180 .001” 1” $991.00 $891.90
• Extension pipe type• With 1”, 2”, 4”, 8”,
16” (2 pcs.) extension pipes
ORDER NO. 177-187SALE $245.70Reg. List $273.00
SETTING RING• 2” Steel setting ring• For accurate setting of
bore gauges and inside micrometers LIMITED QUANTITIES!
OPTIONAL ACCESSORIES List SPECIAL 905338 SPC Cable 40” / 1m $46.30 $41.67905409 SPC Cable 80” / 2m $51.00 $45.90
Each set includes complete gauges, display units and measuring heads for each size and extension rod
8
SAVER
2424S-19
1 Shockproof, jeweled bearings2 Flat back
Range Range/Rev Order No. Graduation Dial List Price SPECIAL
.05” .01” 2805S-101 .0001” 0-5-0 $186.00 $167.40
1” .1” 2416S-10 .001” 0-100 $129.00 $116.10
1” .1” 2416SB-102 .001” 0-100 $129.00 $116.10
2” 1” 2424S-191 .001” 0-100 $227.00 $204.30
SERIES 2 DIAL INDICATORS
• With max/min value holding function, the signal ID-C can output the signal of the GO/NG judgment result against the peak values set
• ABSOLUTE encoder technology• Green/red LED and GO/NG output
function• ISO/JIS type - Stem dia. 8mm• Lug back
• Resolution: .0005”/0.01mm• IP66 protection• ABSOLUTE encoder technology• Slim body design 1.38”x2.36”
is advantageous for multi-point measurements
• Waterproof data output connector
• SPC output• Stem dia. 3/8”
ABSOLUTE ID-N INDICATOR
ABSOLUTE ID-C INDICATOR
Range Order No. Resolution List Price SPECIAL
.5”/12.7mm 543-281 .00005”/
0.001mm $765.00 $688.50
Range Order No. List Price SPECIAL
.5”/12.7mm 543-571 $390.00 $351.00
DIAL TEST INDICATORS
2805S-10
2416S-10
• Popular indicators for a wide range of applications
• Lug back• ANSI/AGD Type• Stem Dia. 3/8”
OPTIONAL ACCESSORIES List SPECIAL 21EAA194 SPC Cable 40” / 1m $51.00 $45.9021EAA190 SPC Cable 80” / 2m $60.00 $54.00
SERIES 1 DIAL INDICATOR
ORDER NO. 1411SSPECIAL $98.10Reg. List $109.00
• Range: .25”, Range/rev.: .1”• Graduation: .001”• Dial reading: 0-50-0• ANSI/AGD type - Stem dia. 3/8”
Range Order No. Graduation Dial Type List Price SPECIAL
.008” 513-403T .0001” 0-4-0 1,2,5 $230.00 $207.00
0.2mm 513-405T 0.002mm 0-100-0 1,2,5 $218.00 $196.20
1mm 513-415E 0.01mm 0-50-0 1,2,3,6 $170.00 $153.00
.016” 513-443 .0001” 0-4-0 1,2,4,6 $242.00 $217.80
.03” 513-452 .0005” 0-15-0 1,2,6 $186.00 $167.40
0.8mm 513-517E 0.01mm 0-40-0 2,6 $139.00 $125.10
513-405EHorizontal style 513-443
Horizontal 20o
tilted face style
513-517EPocket style
513-452Vertical style
4 Revolution counter5 Full Accessory Set6 Basic Accessory Set
Type Codes
1 Anti-magnetic2 Jeweled3 Long contact point
MAGNETIC STAND
ORDER NO. 7011S-10SPECIAL $99.00Reg. List $110.00
• Magnetic stand with fine adjustment
• Accepts all dial and test indicators
9
ABSOLUTE DIGIMATIC CALIPER
SAVERZONE
SUPER
• Range: 0-12”• Graduation: .001”• With 12 interchangeable rods• Base size 2.5 x .63”
ORDER NO. 129-149SUPER SAVER PRICE $293.25Reg. List $391.00
DEPTH MICROMETER
SAVE 25%OFF REG. LIST
• Range: 0-12”/0-300mm• Resolution: .0005”/0.01mm• SPC data output• ABSOLUTE encoder technology
ORDER NO. 500-173SUPER SAVER PRICE $404.80Reg. List $506.00
SUPER SAVER PRICES FOR THESE ITEMS ARE VALID FOR AUGUST 2014 ONLY
SAVE 20%OFF REG. LIST
ABSOLUTE DIGIMATIC CALIPERS
DIAL CALIPER
• Ultra smooth sliding and high shock protection• TiN coating is applied to the sliding surface to increase wear
resistance
Range Order No. Graduation Range/Rev List Price SPECIAL
0-6” 505-717 .001” .2” $137.00 $123.30
• ABSOLUTE encoder technology
Range Order No. List Price SPECIAL
200mm 500-713-10 $400.00 $360.00
8”/200mm 500-753-10* $316.00 $284.40
8”/200mm 500-763-10 $367.00 $330.30
12”/300mm 500-764-10 $506.00 $455.40
ABSOLUTE COOLANT PROOF CALIPERS VERNIER CALIPERS
Range Order No. List Price SPECIAL
40”/1000mm 500-507-10 $1,895.00 $1,705.50
6”/150mm 500-159-30* $266.00 $239.40
• Resolution: .0005”/0.01mm
• With SPC data output
*Without SPC data output, carbide jaws for OD measurement
• IP65 protection• Resolution: .0005”/0.01mm or 0.01mm• With SPC data output• ABSOLUTE encoder technology
*Without SPC data output
OPTIONAL ACCESSORIES List SPECIAL 05CZA624 SPC Cable 40” / 1m $108.00 $97.2005CZA625 SPC Cable 80” / 2m $115.00 $103.50
Range Order No. Graduation List Price SPECIAL
200mm/8” 530-118 0.02mm/.001” $122.00 $109.80
• High accuracy model• Dual reading scales• Lock screw for holding sliding jaw position
Range Order No. Graduation List Price SPECIAL
150mm/6” 531-122 0.05mm/1/128” $105.00 $94.50
150mm/6” 531-128* 0.02mm/.001” $105.00 $94.50
200mm/8” 531-129* 0.02mm/.001” $119.00 $107.10
• Slider moves only when the spring loaded thumb clamp is depressed
• Metric/Inch dual scale
AUGAUGUSTONLY
*High accuracy model
10
TM-505/510 TOOLMAKER’S MICROSCOPES
FEATURES
• Suited for measuring dimensions and angles of machined metals• Check the shape of screws and gears by attaching an optional reticle• Easy angle measurement• Illumination intensity is adjustable
HR-500 ROCKWELL HARDNESS MACHINEFEATURES
• Multiple test force generation for Rockwell, Rockwelll Superficial and Brinell hardness
• Real time electronic test force control for accurate loading, eliminating load force overshooting
• Auto-stop elevation table and automatic preliminary test force loading to provide stable test force generation
Model TM-505D TM-510D
Order No. 176-808A 176-809A
XY stage travel range 2 x 2" / 50 x 50mm 4 x 2" / 100 x 50mm
Measurement method Digimatic Micrometer Head IN/MM (164-164 2pc)
Digimatic Micrometer Head IN/MM (164-164 2pc)
XY stage table top size 6 x 6" / 152 x 152mm 9.4 x 6" / 240 x 152mm
Effective area of table 3.8 x 3.8" / 96 x 96mm 6 x 3.8" / 154 x 96mm
Max. workpiece height 4.5" / 115mm 4.2" / 107mm
Max. stage loading 11lbs
SPECIAL $5,373.00List Price $5,970.00
$6,561.00$7,290.00
Model HR-521
Order No. 810-202-03A
Preliminary Test Force 29.42N (3kgf), 98.07N (10kgf)
Test Force
Rockwell 588.4N (60kgf), 980.7N (100kgf), 1471N (150kgf)
Rockwell Superficial 147.1N (15kgf), 294.2N (30kgf), 441.3N (45kgf)
Brinell 1839N (187.5kgf) (for use with 2.5mm ball)
Maximum Specimen Height Height: 205mm Depth: 150mm from center of indenter shaft
SPECIAL $15,300.00List Price $17,000.00
Angle reading
TM-505D
Indenter Indenter
Indenter
Various shapes of specimen can be measured.(Nose-type indenter axis mechanism has been adopted)
The nose-type indenter mechanism allows measurement of pipe samples as well as the top surface of a flat sample.
• Touch screen operation with back-lit LCD graphic display
• Remote selection of the test force linked to the hardness scale selection
• Cylindrical and spherical surface compensation
• Data offset• Conversion to other hardness
scales• Powerful statistical processing
with flexible data point editing and 1024 data memory
• Measured data editing• OK/±NG tolerance judgment• Statistical processing, histogram
and x̄-R chart
11
Packages consists of:• X Axis AT715 Linear Scale• Y Axis AT715 Linear Scale• KA Counter (2 axis)• Universal Bracket kit• Screw kit• Arm kit (KA Counter)
DIGITAL READOUT PACKAGES
OR
DRO PACKAGES FOR MILL APPLICATIONS
Size Order No. PKG. PRICE
12” x 30” D950-989 $1,453.50Reg. Pkg. Price $1,530.00
Compare at $1,917.00 if purchased separately
12” x 36” D950-991 $1,477.25Reg. Pkg. Price $1,555.00
Compare at $1,950.00 if purchased separately
16” x 36” D950-992 $1,477.25Reg. Pkg. Price $1,555.00
Compare at $1,961.00 if purchased separately
KA COUNTER• High performance, low cost counter• Features both mill, lathe and standard functions• Compatible with AT715 electromagnetic scales
and AT100 series glass scales
AT715 LINEAR SCALE• IP67 environmental resistance
• ABSOLUTE encoder technology• 2 mounting directions of the scale main
unit allows flexible mounting options
WARRANTYFIVE YEAR
ON ALL AT715 LINEAR SCALES
CMM
Note: All information regarding our products, and in particular the illustrations, drawings, dimensional and performance data contained in this printed matter as well as other technical data are to be regarded as approximate average values. We, therefore, reserve the right to make changes to the corresponding designs. The stated standards, similar technical regulations, descriptions and illustrations of the products were valid at the time of printing. In addition, the products are subject to Canadian Export Administration
Regulations. Re-export or relocation of Mitutoyo products may require prior approval by an appropriate governing authority. We have tried to be as accurate as possible, however, there may be some errors in text, specifications or price. Please confirm with your customer service rep. Some items may not be exactly as shown. Prices are in Canadian dollars, unless otherwise specified. Applicable taxes and shipping charges are extra.© 2014 Mitutoyo Canada Inc., Mississauga ON Canada We reserve the right to change specifications and prices without notice.
www.mitutoyo.ca Toronto (905) 821-1261 Montréal (514) 337-5994Mitutoyo Canada Inc.
12
NEWSMANUAL
Included with each CNC Coordinate Measuring Machine and Vision System, the Gold Care Productivity Pack reduces theoverall cost of ownership by including:
+ TWO YEAR WARRANTY + TWO YEAR CALIBRATION AGREEMENT + MEASURLINK® PRO EDITION QUALITY DATA + MANAGEMENT SOFTWARE + MITUTOYO ECO-FIX® FIXTURE SYSTEM + MITUTOYO STARTER STYLUS KIT + LIFETIME SOFTWARE TECHNICAL PHONE SUPPORT
FIVE YEAR WARRANTY For Manual CMMs
In celebration of the 80th Anniversary of Mitutoyo Corporation headquarters in Japan, we are pleased to offer a FIVE YEAR WARRANTY for manual Coordinate Measuring machines sold in Canada in 2014.
The extended warranty program was initiated after closely listening to the “cost of ownership” and “simplified buying” desires of metrology equipment buyers.
With our FIVE YEAR WARRANTY, factory trained service technicians located across the country, and lifetime telephone software support, there’s no need to look any further for the best value available in measurement products and backup services.
GOLD CARE PACKAGE For CNC CMMs and VISION systems
MCOSMOSVERSION 4.0
UpgradeBringing the next generation of CMM software to your QC lab or shop floor. MCOSMOS Version 4.0 offers full support for the widest range of probe head configurations. This means more options, more speed, more productivity and more convenience for your inspection team.
CMMNEWSCNC
CALL TODAY FOR MORE INFORMATION OR TO REQUEST
A QUOTATION
MEASUREMENT MADE SIMPLE• Offline Programming Option
• Automatic Element Recognition
• Parametric Part Programming
• Gasket Scanning Function
• Programmable Variables
• Multi-circle Function
• Best Fit of Profiles
CONTACT YOUR MITUTOYO SALES REPRESENTATIVEFOR INFO AND PRICING.
On sale for a limited time