Technical Manual Imac21 Inch Late09
-
Upload
peerapatkaewvirat -
Category
Documents
-
view
213 -
download
0
Transcript of Technical Manual Imac21 Inch Late09
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 1/218
Apple Technician Guide
iMac (21.5-inch, Late 2009) Updated: 2009-11-24
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 2/218
Apple Inc.
© 2009 Apple Inc. All rights reserved.
Under the copyright laws, this document may not be copied, in whole or in part, without thewritten consent of Apple.
Every eort has been made to ensure that the information in this document is accurate. Apple
is not responsible for printing or clerical errors.
Apple
1 Innite Loop
Cupertino, CA 95014-2084
USA
+ 1 408 996 1010
www.apple.com
Apple, the Apple logo, Mac, and Macintosh are trademarks of Apple Inc., registered in the U.S.and other countries.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 3/218
iMac (21.5-inch, Late 2009)
Contents
About This Guide
Updates 9Updated 24 November 2009 9Updated 28 October 2009 9Introduced 20 October 2009 9
Feedback 9
Basics
Overview 11Identifying Features 11Product Congurations 12
Wireless Troubleshooting 12
Safety 12
Serial Number Location 13
TroubleshootingGeneral Troubleshooting 15
Wireless Troubleshooting 15Update System Software & Firmware 15
Troubleshooting Theory 15Hardware vs. Software 15Common Reset Procedures 16
Power On Self Test (POST) 16Resetting the System Management Controller (SMC) 16Resetting Parameter RAM (PRAM) 17
Starting Up in Safe Mode 17Apple Service Diagnostics 18Diagnostic LEDs 19
LED Functions 20
LED Startup Sequence 21
Logic Board Test Points 22
Sensor and Fan Connector Locations 23
Block Diagram 24
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 4/218
Symptom Charts 25Startup and Power 25
No Power, Dead Unit 25Won’t Start Up 27
Intermittent Shutdown 29
Kernel Panic, System Crashes 31No Video 33
Corrupted Video 34
Burnt Smell/Odor 37
Uncategorized Symptoms 38Display 39
Backlight Issue/No Backlight 39
Noise / Unstable Flickering 41
LCD Image Issues 43
Incorrect/Missing Colors 44
Distorted/Blurred Image 45
Pixel Anomalies 47Vertical/Horizontal Lines 48Non-Uniform Brightness 50
Cosmetic Defects 51
Uncategorized Symptoms 51
Mass Storage 52
Hard Drive Not Recognized 52
Hard Drive Read/Write Errors 54
Hard Drive Noisy 55Optical Drive Not Recognized 57
Optical Drive Won’t Accept/Eject Media 58
Optical Drive Read/Write Error 59
Optical Drive Not Performing to Specications 61
Optical Drive Noisy 62
SD Card Will Not Insert Into Slot 63
SD Card Not Recognized 64
Uncategorized Symptoms 65Communications 66
AirPort/Bluetooth Issues 66AirPort Card Kernel Panic 68Ethernet Port/Device Issue 69
Wireless Input Device Doesn’t Pair 70
Wireless Input Device Loses Connection 72
Uncategorized Symptoms 74
Input/Output Devices 75Apple Remote Inoperable 75Audio: Microphone 77
Audio: Built-in Speakers Have Distorted Sound 78Audio: Built-in Speakers Have No Audio 79
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 5/218
Camera Issues 81
FireWire Device Not Recognized 82
USB Device Not Recognized 84
Wired Keyboard Does Not Function Properly 86Keyboard: Specic Keys Do Not Respond 88
Wired Keyboard/Mouse Not Recognized 88Uncategorized Symptoms 90
Mechanical 91
Noise/Hum/Vibration 91
Fan Failures / Thermal Issues 94
Stand/Hinge Issues 95Physical Damage 96Uncategorized Symptoms 96
Take Apart
General Information 98Opening the Unit 98Required Tools 98
Required Special Tools for Glass Panel 99
Cleaning Tools Starter Kit 99
Cleaning Tool Resources 99
Cleaning & Handling the Glass Panel 100
Do’s and Don’ts 100
Handling a Broken Glass Panel 100
How to Remove a Broken Glass Panel 101
Safety 105
Logic Board Handling 106Note About Images in This Guide 106
Access Door 107
Memory 109
Glass Panel 111Removal 112
Reassembly 113
Camera 116
LCD Panel 118
Vertical Sync Cable 122
LCD Temp Sensor Cable 123
LVDS Cable 124
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 6/218
Bluetooth Antenna 125
Bluetooth Board 127
AirPort Antenna 129
AirPort Card 131AirPort Cable 133
AirPort Carrier Board 135
LED Backlight Board 137
Power Supply 139
Backlight Pressure Wall 141
Power Supply Pressure Wall 143
Hard Drive 145
Hard Drive Sensor Cable 148
Bluetooth Cable 150
Camera Cable 153
Optical Drive 156
Optical Drive Sensor Cable 159
Optical Drive Fan 161SD Board 163
SD Cable 165
Audio Cable 167
IR Board & Cable 169
Logic Board 171
Video Card 178
Battery 180
Hard Drive Data Cable 182
Optical Drive Data Cable 184
Cable, AC/DC Power/Backlight/SATA 186
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 7/218
CPU Fan 187
Ambient Temp Sensor 190
Left Speaker 192
Right Speaker 194Hard Drive Fan 196
Mechanism Cover 198
Stand 200
Mechanism 202
Microphone Cable 204
Rear Housing 205
Views
Exploded Views 208iMac (21.5-inch, Late 2009), Part 1 208iMac (21.5-inch, Late 2009), Part 2 209
iMac (21.5-inch, Late 2009), Part 3 210
Screw Chart 211
External Views 213
Front View 213Rear View 214
I/O Ports 215
Internal Views 216Photo of Components below LCD 216Photo of Components below Logic Board 217
Logic Board, Front Side 218Logic Board, Back Side 218
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 8/218
© 2009 Apple Inc. All rights reserved.
Apple Technician Guide
About This GuideiMac (21.5-inch, Late 2009)
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 9/218
iMac (21.5-inch, Late 2009) — Updates 92009-11-24
Updates
Updated 24 November 2009
TroubleshootingGeneral: Updated close-up image of diagnostic LEDs.•Mechanical: Fan noise issues: updated two topics, “Noise/Hum/Vibration” and “Fan Failures/•
Thermal Issues” with the following information:Check: Verify if any tape, gasket, cable label, or cable is touching the fan blades and•causing a ticking noise.Actions: Secure the material so it doesn’t touch fan blades. If tape adhesive has lost its•stickiness, replace that section of tape.
Take ApartGeneral Information: Added images to section “How to Remove a Broken Glass Panel.”•Hard Drive and Hard Drive Sensor Cable: Added information about connecting sensor cables•to Western Digital drives: Orient the drive with its circuit board facing up and connect thesensor cable to the hard drive pins, leaving the 2 left pins unconnected (exposed).Logic Board: Added note that logic board may be easier to remove if RAM is removed rst.•
ViewsExploded Views: Added part numbers for Power Supply Pressure Wall (922-9281), Backlight•Pressure Wall (922-9282), Bluetooth Antenna (922-9283), and AirPort Antenna (922-9284).
Updated 28 October 2009Basics: Added another kBase link to Wireless Troubleshooting section.•
Troubleshooting: General: Added another kBase link to Wireless Troubleshooting section.• Take Apart: General: Added• section “How to Remove a Broken Glass Panel.”
Introduced 20 October 2009
Feedback
We want your feedback to help improve this and future Technician Guides!Please email any comments to: [email protected]
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 10/218
© 2009 Apple Inc. All rights reserved.
Apple Technician Guide
BasicsiMac (21.5-inch, Late 2009)
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 11/218
iMac (21.5-inch, Late 2009) Basics — Overview 112009-11-24
Overview
Identifying Features
The iMac (21.5-inch, Late 2009) has an all-aluminum enclosure with a glass front. It can bedistinguished from the previous model by the glass extending all the way to the top, left andright edges, rather than having an aluminum bezel that borders the glass. Also, the rear of thecomputer is aluminum rather than black plastic.
This model’s other new features include:Larger and LED-backlit 21.5-inch 16:9 display with 1920x1080 native HD resolution•Increased processor speeds: 3.06 GHz or 3.33 GHz Intel Core 2 Duo•Integrated NVIDIA GeForce 9400M or ATI Radeon HD 4670 graphics•
Four RAM memory slots: two slots are lled with at least 2GB each, for a total of 4GB;•maximum RAM is 16GBLarger hard drive options: 500GB, 1TB, 2TB (CTO only)•SD card reader•New Apple Wireless Keyboard and wireless Magic Mouse, standard with all congurations•Ships with and requires at least Mac OS 10.6.1 (Snow Leopard)•
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 12/218
iMac (21.5-inch, Late 2009) Basics — Overview 122009-11-24
Product Congurations
For product congurations, refer to AppleCare Tech Specs: http://support.apple.com/specs/
Wireless Troubleshooting
If you’re having issues with Bluetooth and wireless connectivity issues, refer to the followingApple Knowledge Base articles:
kBase #TS3048: Desktop computers: Troubleshooting wireless mouse and keyboard issues kBase #HT1365: AirPort and Bluetooth: Potential source of interference kBase #HT3903: Apple Wireless Keyboard and Mouse: How to install batteries
Safety
Warning: HIGH VOLTAGE:The AC/DC power supply PCB remains powered up wheneversystem is plugged in, whether or not system has been turned on. Use extreme cautionwhen troubleshooting system with glass panel and LCD panel removed.
Important: If computer is shut down by removing power cord, allow power supply a good 2-3minutes to discharge capacitors before handling it. However, if you select “Shut Down” via theApple menu, the computer will discharge power supply capacitor almost immediately.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 13/218
iMac (21.5-inch, Late 2009) Basics — Overview 132009-11-24
Serial Number Location
The iMac (21.5-inch, Late 2009)’s serial number is located on the bottom of the stand. Whenreplacing a stand, transfer the serial number to the new stand.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 14/218
© 2009 Apple Inc. All rights reserved.
Apple Technician Guide
TroubleshootingiMac (21.5-inch, Late 2009)
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 15/218
iMac (21.5-inch, Late 2009) — General Troubleshooting 152009-11-24
General Troubleshooting
Wireless Troubleshooting
If you’re having issues with Bluetooth and wireless connectivity issues, refer to: kBase #TS3048: Desktop computers: Troubleshooting wireless mouse and keyboard issues kBase #HT1365: AirPort and Bluetooth: Potential source of interference kBase #HT3903: Apple Wireless Keyboard and Mouse: How to install batteries
Update System Software & Firmware
Important: Whenever possible before beginning troubleshooting, ensure the latest softwareand rmware updates have been applied.
Firmware is the name given to software that is written into memory circuits such as ashmemory, that will hold the software code indenitely, even when power is removed fromthe hardware. Firmware on Intel Mac computers is designed to be updated if necessary byrunning the Mac OS X Software Update check (available in the Apple menu) while computer isconnected to the Internet. For more information about rmware updates, refer to: kBase # HT1557: About rmware updates for Intel-based Macs
Troubleshooting Theory
For general information on troubleshooting theory, go to GSX and nd the Service Training
course menu link. From there you can access the Troubleshooting Theory self-paced course.
Hardware vs. Software
For information on how to isolate a hardware issue from a software issue, refer to: kBase #TS1388: Isolating issues in Mac OS X
For information on how to troubleshoot a software issue, refer to:kBase #HT1199: Mac OS X: How to troubleshoot a software issue kBase #TS1394: Mac OS X: Troubleshooting installation and software updates kBase #HT2956: Troubleshooting Mac OS X installation from CD or DVD
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 16/218
iMac (21.5-inch, Late 2009) — General Troubleshooting 162009-11-24
Common Reset Procedures
Power On Self Test (POST)
Intel-based Mac computers such as the iMac rely on a combination of tones to indicate PowerOn Self Test (POST) error codes.
If the computer detects out-of-specication or no SDRAM, the screen will remain black•but the computer will beep. This error condition may be due to physically damaged RAM,installing incorrect type of RAM, or not having RAM installed.Some RAM may appear to pass the Power-On-Self-Test (POST) but still cannot be used by•the operating system. In this case, the computer will display a gray screen, sound threetones and repeat tones until computer is turned o.
The solution to both situations is to rst re-seat memory and test computer again. If•memory fails POST again, remove all installed memory and test by installing one by oneeach memory that has been veried to work correctly on another system (i.e., “known-good”) or order new memory.
For more information, refer to: kBase #HT2538: iMac (Mid 2007) and later models: About new startup tones
Resetting the System Management Controller (SMC)
The System Management Controller (SMC) is a chip on logic board that controls all powerfunctions. If computer is experiencing any power issue, such as not starting up, not displayingvideo, sleep issues, or fan noise issues, resetting SMC may resolve it. To reset SMC on an iMac:
From Apple menu, choose Shut Down (or if the computer is not responding, hold power1.button for approximately ten seconds until it powers o).
Unplug all cables from computer, including power cord.2.
Wait at least 15 seconds. SMC reset occurs automatically once iMac has been unplugged3.from AC power source for several seconds.
Plug power cord back in, making sure power button is not being pressed.4.
Press power button on back to start up computer.5.
For more information, refer to: kBase #HT1543: Intel-based iMac: How to reset the System Management Controller
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 17/218
iMac (21.5-inch, Late 2009) — General Troubleshooting 172009-11-24
Resetting Parameter RAM (PRAM)
PRAM stores certain system and device settings in a location that Mac OS X can access quickly.Exactly which settings are stored in the computer’s PRAM varies depending on the type ofcomputer as well as the types of devices and drives connected. To reset PRAM:
Shut down the computer.1.
Locate the following keys on keyboard: Command, Option, P, and R. You will need to hold2.these keys down simultaneously in Step 4. Note: If the keyboard does not have an Option key, use the Alt key instead.
Press power button.3.
Immediately press and hold Command-Option-P-R keys. 4.Important: You must press this key combination before the gray screen appears.
Hold down keys until the computer restarts, and you hear the startup chime a second time.5.
Release keys.6.
For more information, refer to: kBase #HT1242: Mac OS X: What’s stored in PRAM
kBase #HT1379: Resetting your Mac’s PRAM and NVRAM
Starting Up in Safe Mode
Starting up into Safe Mode does several things that can help resolve software or directoryissues that may exist on the startup volume. To start up in Safe Mode:
Shut down the computer.1.
Press power button.2.Immediately after you hear startup tone, press and hold Shift key. 3.Note: The Shift key should be held as soon as possible after startup tone but not before.
Release Shift key when you see the screen with a gray Apple and progress indicator (looks4.like a spinning gear). Note that booting into Safe Mode will take longer than a normalstartup. During startup, the words ”Safe Boot” will appear on Mac OS X startup screen.
To leave Safe Mode, restart computer normally, without holding down any keys during5.startup.
For more information, refer to:
kBase #HT1564: Mac OS X: What is Safe Boot, Safe Mode? kBase #TS1884: Safe Boot takes longer than normal startup
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 18/218
iMac (21.5-inch, Late 2009) — General Troubleshooting 182009-11-24
Apple Service Diagnostics
Run Apple Service Diagnostic version 3S133 to determine if any thermal sensors or blowers aremalfunctioning. If ASD is not available, run Apple Hardware Test by holding down the D keyduring startup. When a test reports an error, reseat appropriate connections. If issue persists,replace the corresponding part (sensor, fan, logic board, video card, or power supply). See chartbelow for correlation between error code, aected sensor, sensor location (stand-alone, or partof a sub-assembly), and additional checks to perform.
Error Sensor and Location Check
TA0P Ambient temp sensor stand-alone part, located near CPU fan
Check sensor cable connectionto logic board, run CPU fan test,check air ow.
TC0H CPU heatsink sensor part of logic board
Check CPU sensor cableconnection to logic board, runCPU fan test, check air ow.
TG0D MXM GPU die sensor part of MXM video card
Run ODD fan test, check airow.
TG0H MXM GPU heatsink sensor part of MXM video card
Check video card sensor cableconnection to logic board, runODD fan test, check air ow.
TH0O HDD sensor stand-alone part, located on hard drive
Check sensor cable connectionto logic board, run HDD fantest, check air ow.
TL0p LCD temp sensor stand-alone part, located on back of LCD panel
Check sensor cable connectionto logic board, run all fans tests,
check air ow. TN0H MCP79 heatsink
part of logic board, located on heatsink Check sensor cable connectionto logic board, run HDD fantest, check air ow.
TO0p ODD sensor stand-alone part, located on optical drive
Check sensor cable connectionto logic board, run ODD fantest, check air ow.
Tp1P PS1 T1 proximity sensor part of power supply
Check logic board to powersupply cable connections, runCPU fan test, check air ow. Tp2H PS1 T2 secondary heatsink sensor
part of power supply
Tp3H PS1 T1 primary heatsink sensor part of power supply
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 19/218
iMac (21.5-inch, Late 2009) — General Troubleshooting 192009-11-24
Diagnostic LEDs
Depending on iMac model, there are either three or four built-in diagnostic LEDs on the logicboard that can help troubleshoot the computer. LEDs are located on bottom right edge of logicboard (under a piece of black mylar tape) and can only be seen when looking through lowervents of rear housing.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 20/218
iMac (21.5-inch, Late 2009) — General Troubleshooting 202009-11-24
LED Functions
LED #1Indicates that trickle voltage from power supply has been detected by logic board. This LED•will remain ON whenever the iMac is connected to a working AC power source. The LED willremain on even when computer has been shut down or put to sleep. The LED will turn oonly if AC power source is disconnected or power supply is faulty.
LED #2Indicates that logic board has detected power from power supply when computer is•turned on. This LED will be ON when computer is turned on and power supply and voltageregulators are working correctly.
LED #3
Indicates that computer and video card are communicating. This LED will be ON when•computer is communicating properly with video card. If LEDs 1 and 2 are ON and you heardthe startup sound, but LED 3 is OFF, then video card might be installed incorrectly or needreplacement. Note: LED #3 is not present on models with integrated graphics.
LED #4Indicates that computer and LCD panel are communicating. This LED will be ON when•computer is turned on and video signal is being generated. If LED 4 is ON and there isno image on display, then LCD panel, LED backlight board, or cables between might beinstalled incorrectly or need replacement.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 21/218
iMac (21.5-inch, Late 2009) — General Troubleshooting 212009-11-24
LED Startup Sequence
LED #1 = Power available.
If no LED is visible:Verify AC source•
Verify known-good AC cable is connected• Verify cable connection between AC inlet and power supply•Verify cable connection between power supply and logic board•Verify power supply•
LED #1 + LED #2 = Power available, and system is powered on.
If second LED is not visible when power button is pressed:Verify power button connection to logic board•Verify power button functionality•Verify cable connection between power supply and logic board•Verify power supply•
Verify logic board•
LED #1 + LED #2 + LED #3 = Power available, system is powered on, and video card found.
If third LED is not visible after power on:Verify that MXM video card is seated properly•Verify logic board•
LED #1 + LED #2 + LED #3 + LED #4 = Power available, system is powered on, video cardfound, and internal LCD found.
If fourth LED is not visible after power on:
Verify cable connections between LCD panel and logic board•Inspect LCD display cables for cable damage•Verify external video functionality, and according to result check the following items:•-If external display works then verify/replace LED backlight board-If external display works then verify/replace LCD panel-If external display does not work verify/replace logic board
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 22/218
iMac (21.5-inch, Late 2009) — General Troubleshooting 222009-11-24
Logic Board Test Points
Test points, which can be used to verify proper power ow, are accessible on logic board whenLCD panel is removed. All voltages given in Troubleshooting Symptom Charts assume thatcomputer is plugged into a known-good power outlet with a known-good AC cable. Someguidelines for using test points:
Warning: HIGH VOLTAGE:• Use extreme caution when live testing!Do NOT lean over or touch the power supply area during live testing.•Keep your ngers behind nger guards on test probes when measuring.•
Turn dial of voltmeter/multimeter to measure DC (direct current, usually indicated by a solid•horizontal line over dashes). If your voltmeter requires a set voltage range, choose a DCrange that includes the voltage you are measuring.Connect black probe to ground. Connect red probe to test point and verify voltage.•
For more info, see kBase #HT3250: Diagnostics: Using a digital multimeter
Logic Board Test Point Function
Pin 1 Ground
Pin 4 Standby 12V power (permanent power coming from power supplyand present as long as AC cable is connected, even if computer iso); corresponds to LED #1
Pin 6 Backlight Control pulse width modulated signal (from logic boardto LED backlight board, to adjust the backlight level setting
according to user setup)Pin 11 12V Run-Mode power to logic board (coming from power supply,
present as long as system is on or asleep); corresponds to LED #2
Pin 12 Power On Request signal (from logic board to power supply whenpower button is pressed)
Pin 13 Backlight Enable (signal from logic board to Backlight Controllerboard, to enable backlight
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 23/218
iMac (21.5-inch, Late 2009) — General Troubleshooting 232009-11-24
Sensor and Fan Connector Locations
Ambient temp sensors and fans connectors locations are shown below. Ensure cables arecorrectly routed and the sensors and fans are properly connected. If a sensor or fan is faulty ornot connected, Apple Hardware Test and Apple Service Diagnostic will generate an error code.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 24/218
iMac (21.5-inch, Late 2009) — General Troubleshooting 242009-11-24
Block Diagram
Refer to this diagram to see how modules are interrelated.
SO-DIMM
Antenna
Antenna
AntennaSO-DIMM
Temperature
Sensor
Temperature
Sensor
Fan
MLB
SO-DIMM
Display
AC/DC
Power
Button
Bluetooth
Speakers
Hard DriveOptical Drive
AC Inlet
Temperature
Sensor
Camera
Microphone
Speakers
Backlight
Controller
Fan
Fan
MXM
802.11n
Ambient
Temperature
Sensor
IR Sensor
SD Card
Reader
SO-DIMM
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 25/218
iMac (21.5-inch, Late 2009) Symptom Charts — Startup and Power 252009-11-24
Symptom Charts
Follow steps in the order indicated below. If an action resolves the issue, retest system to verify.
Note: A compilation of Quick Check tables is available at: http://service.info.apple.com/QRS/en/quickreference.pdf
Startup and Power
No Power, Dead Unit
Unlikely cause: speakers
Quick Check
Symptoms Quick Check
No Power, Dead UnitNo power•No fan spin•No startup chime•No image on external display•No hard drive or optical drive•activity
Verify power source.1.
Verify power cable.2.
Listen closely for signs of activity from system3.including: rotating fans, hard drive or optical driveactivity, startup chime, etc.
Deep Dive
Check Result Action Code
Power ON system. Verify if1.there is any indication that thesystem has powered up (fanrotation, hard drive or opticaldrive noise, backlight turns on).
Yes The symptom is poweringup. Go to Won’t Start Up
symptom ow.
No Go to step 2.
Locate diagnostic LEDs in2.
bottom case vents. Plug ACcord into system. Verify ifdiagnostic LED #1 turns ON.You may alternately check forpresence of a 12V DC signalbetween pin 4 and pin 1 oflogic board.
Yes Standby power voltage being
supplied by power supply. Go to step 3.
No Replace power supply.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 26/218
iMac (21.5-inch, Late 2009) Symptom Charts — Startup and Power 262009-11-24
Press power button while3.monitoring diagnostic LEDs.Verify if LED #2 turns ON andremain ON after pressingthe power button. You mayalternately check for a power
request signal between pin 12and pin 1 of logic board.
Yes Power supply functioning andlogic board detects supplyvoltages. Go to Won’t StartUp symptom ow.
No Go to step 4.
Disconnect AC cable then4.remove power supply andcarefully inspect connectorsbetween AC inlet and powersupply, then DC connectors andcables between power supplyand logic board, for damage orpoor connections.
Yes Replace damaged part. P16
No Go to step 5.
Inspect power button and5.verify if it is properly connectedto the logic board.
Yes Go to step 6.
No Reconnect power button.
Disconnect power button from6.logic board. Inspect cable andconnector for damage. Verifycontinuity between the twopins of power button when it ispressed.
Yes Power button is functioningcorrectly. Reconnect powerbutton to logic board and
go to step 7.
No Power button faulty. Replacerear housing (which includespower button).
X14
Press power button and Verify7.if system turns ON. You may
alternately check for presenceof a 12V DC signal betweenpin 11 and pin 1 of logic boardwhen power button is pressed.
Yes Power supply functioning. Ifsystem still won’t boot, go
to Won’t Start Up symptomow.
No Replace DC power cable. Go to step 8.
X03
Press power button and verify if8.system turns ON.
Yes Issue solved with replaced DCpower cable.
No Replace power supply. Go to step 9.
P01
Press power button and verify if9.system turns ON.
Yes Issue solved with replacedpower supply.
No Reinstall power supply andreplace logic board.
M01
Note: If No Power symptom persists after all steps have been followed use minimumconguration troubleshooting to proceed. Try disconnecting hard drive, optical drive, AirPort,Bluetooth, and SD card modules to determine if one of them is preventing the power supplyfrom functioning.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 27/218
iMac (21.5-inch, Late 2009) Symptom Charts — Startup and Power 272009-11-24
Won’t Start Up
Quick Check
Symptoms Quick Check
Won’t Start UpNo startup chime.•Error tones during startup.•Grey screen with fan noise, or•other noise.Will not progress beyond •Apple logo or spinning gear.
Isolate OS by starting up from original install1. media for this computer, from a same-modelcomputer in Target Disk Mode, or from acompatible known-good OS on an external drive.Both AirPort and Bluetooth services are availablewhen booted from the Install disk.
Reset SMC and PRAM to clear any stored,2.corrupted information.
Start up in Safe Mode by holding shift key down3.during startup to load only required kernelextensions and disable all startup and loginitems. See kBase #HT1564: Mac OS X: What is
Safe Boot, Safe Mode?If system generates error tones there may be an4.issue with the SDRAM. See kBase #HT2341: Intel-based Mac: Power On Self Test RAM error codes
Identifying when in the startup process the5.computer hangs can help isolate the issue. See kBase #HT2674: Intel-based Mac: Startupsequence and error codes, symbols forinformation on the Macintosh startup sequence,and error codes and symbols used.
Deep Dive
Check Result Action Code
Boot computer to Apple1.Hardware Test on the internalhard drive or an inserted InstallDVD by holding down the Dkey at startup. Verify if systemboots up from any of thesevolumes.
Yes Run the extended testsand proceed with results. IfAHT passes or boots with amemory error, go to step 2.
No Go to step 2.
Remove installed SDRAM, and2.test with known-good SDRAM.Verify if computer starts upproperly now.
Yes SDRAM issue. Reinstall oneof user’s SDRAM modulesand retest. Proceed one byone to nd the faulty SDRAMmodule, and replace it.
X02
No Go to step 3.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 28/218
iMac (21.5-inch, Late 2009) Symptom Charts — Startup and Power 282009-11-24
Wait 15 seconds after computer3.was powered down anddisconnect AirPort cable fromlogic board. Verify if computerstarts up properly now.
Yes Go to AirPort Card KernelPanic symptom ow.
No Go to step 4.
Disconnect hard drive SATA4.cable and startup from InstallDVD in the optical drive, orfrom an external bootablevolume. Verify if computerstarts up properly now.
Yes Go to Hard Drive NotRecognized symptom ow.
No Go to step 5.
Reconnect hard drive,5.disconnect optical drive cableand retest. Verify if computerstarts up properly now.
Yes Go to Optical Drive NotRecognized symptom ow.
No Go to step 6.
Remove coin battery on back6.of logic board (you will need to
completely remove logic boardto do this), and leave out forapproximately 1 minute. Thenreinstall battery. This will resetlogic board. Verify if computerstarts up properly now.
Yes Issue resolved by logic boardreset. Measure DC voltage on
battery touching battery withred probe, and groundingwith black probe. If voltage is2.7v or less, replace battery.
For multimeter help, seekBase #HT3250: Diagnostics:Using a digital multimeter.
No Replace logic board. M02
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 29/218
iMac (21.5-inch, Late 2009) Symptom Charts — Startup and Power 292009-11-24
Intermittent Shutdown
Quick Check
Symptoms Quick Check
Intermittent ShutdownPowers o during startup.•Powers o during desktop use.•Computer restarts•spontaneously.Powers o when waking from•sleep.
Make sure that power cord is securely attached1. to the back of computer, and is not hindered by adesk or other furniture.
Plug computer directly into an AC outlet to test if2.a surge protector or UPS is causing issue.
Open System Preferences > Energy Saver >3.Schedule and make sure that a “Shut Down”event is not scheduled.
Isolate OS by starting up from original install4.media for this computer, from a same-modelcomputer in Target Disk Mode, or from acompatible known-good OS on an external drive.Both AirPort and Bluetooth services are availablewhen booted from the Install disk.
Reset SMC and PRAM to clear any stored,5.corrupted information.
Start up in Safe Mode by holding shift key down6.during startup to load only required kernelextensions and disable all startup and loginitems. See kBase #HT1564: Mac OS X: What isSafe Boot, Safe Mode?
Deep DiveCheck Result Action Code
Verify improper shutdown1.by opening the system.loglocated in /var/log. Filter logfor “shutdown cause”. Entriesof value “0” or a negativevalue indicate an impropershutdown. Verify if you ndrecent entries of an impropershutdown in log le.
Yes Determine if user causedimproper shutdown. Useknown-good AC power cordand AC outlet. Go to step 2.
No Revisit Quick Check examplesfor possible software issues.Check if user is runningother automating softwarethat may be shutting down
system. Verify issue and jumpto appropriate symptomow. No repair needed undercurrent symptom ow.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 30/218
iMac (21.5-inch, Late 2009) Symptom Charts — Startup and Power 302009-11-24
With known-good AC power2.cord and AC outlet, Verify ifsystem continues to restart orshutdown
Yes Go to step 3.
No AC power cord / outlet issue.Issue resolved.
X03
Disconnect hard drive power3.cable from hard drive andstartup the computer fromother bootable media (likeInstall DVD, a same modelcomputer in Target Disk Mode,or a compatible known-goodOS on an external drive). Verifyif system continues to restart orshutdown.
Yes Go to step 4.
No Possible bad software or harddrive. Go to Hard Drive NotRecognized symptom ow.
Inspect and reseat AC inlet4.connection to power supply(the smaller of the 2 cablesconnected to power supply),and DC power cable frompower supply to logic board.Verify if damage is observed onthe cables or connectors.
Yes Replace damaged cable.Retest. Return to step 1 ifproblem continues.
X03
No Go to step 5.
Install known-good power5.supply. Verify if systemcontinues to restart orshutdown.
Yes Reinstall original powersupply. Go to step 6.
No Issue resolved with powersupply replacement.
P02
Replace DC power cable,6.which supplies power to
logic board, hard drive, andLED backlight board. Verify ifsystem continues to restart orshutdown.
Yes Go to step 7.
No Issue resolved with DC powercable replacement.
X03
Replace logic board.7. Verify ifsystem continues to restart orshutdown.
Yes Use Minimum Congurationtroubleshooting to isolatefailed module.
No Issue resolved with logicboard replacement.
M08
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 31/218
iMac (21.5-inch, Late 2009) Symptom Charts — Startup and Power 312009-11-24
Kernel Panic, System Crashes
Quick Check
Symptoms Quick Check
Kernel Panic, System CrashesKernel Panic on startup or•desktop use.System freeze during use.•System freeze upon wake from•sleep.
Isolate OS by starting up from original install1. media for this computer, from a same modelcomputer in Target Disk Mode, or from acompatible known-good OS on an external drive.Both AirPort and Bluetooth services are availablewhen booted from the Install disk.
Ensure that all software and rmware updates for2.this model have been installed to take advantageof any available bug xes.
Reset SMC and PRAM to clear any stored,3.corrupted information.
Start up in Safe Mode by holding shift key down4.during startup to load only required kernelextensions and disable all startup and loginitems. See kBase #HT1564: Mac OS X: What isSafe Boot, Safe Mode?
Check the panic.log, located /Library/Logs/5.Panicreporter, for information in the back tracethat may give clues about the kernel panic.
For more information, see6. kBase #HT1392: About “You need to restart your computer”(kernel panic) messages.
Deep Dive
Check Result Action Code
Boot the computer to Apple1.Hardware Test on internal harddrive or an inserted Install DVDby holding down the D key atstartup. Verify if system bootsup from any of these volumes.
Yes Run extended tests andproceed with results. If AHTpasses or boots with a kernelpanic, go to step 2.
No Go to step 2.
Remove all peripheral devices2.
including keyboard and mouse.Verify if system starts withoutkernel panic.
Yes Add peripheral devices one
at a time until kernel panicrepeats. Replace devicecausing issue.
No Go to step 3.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 32/218
iMac (21.5-inch, Late 2009) Symptom Charts — Startup and Power 322009-11-24
Use known-good SDRAM in the3.system. Verify if system startwithout kernel panic now.
Yes Install user’s SDRAM one byone and test. If kernel panicrepeats, replace aectedSDRAM. Verify if correctSDRAM specication is beingused.
X01
No Go to step 4.
Wait for 20 seconds after4.shutdown and disconnectAirPort cable on logic board.Verify if system starts withoutkernel panic now.
Yes Go to AirPort Card KernelPanic symptom ow.
No Go to step 5.
Disconnect SATA cable from5.hard drive and startup to theInstall DVD in the optical driveor from an external volume.Verify if system starts without
kernel panic now.
Yes Go to Hard Drive NotRecognized symptom ow.
No Go to step 6.
Disconnect camera and6.microphone cables from logicboard. Verify if system startswithout kernel panic now.
Yes Go to Camera Issues orAudio: Microphone symptomow as appropriate.
No Go to step 7.
Disconnect Bluetooth cable7.on logic board. Verify if systemstarts without kernel panicnow.
Yes Go to AirPort/BluetoothIssues symptom ow.
X99
No Go to step 8.
Disconnect SD board on logic8.board. Verify if system startswithout kernel panic now.
Yes Go to SD Card NotRecognized symptom ow.
No Go to step 9.
Disconnect optical drive and9.test. Verify if system startswithout kernel panic now.
Yes Go to Optical Drive NotRecognized symptom ow.
No Replace logic board.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 33/218
iMac (21.5-inch, Late 2009) Symptom Charts — Startup and Power 332009-11-24
No Video
Unlikely cause: hard drive, optical drive, speakers, camera, microphone
Quick Check
Symptoms Quick Check No Video
No image.•Backlight failure.•
Check brightness setting.1.
For no-video issues, connect an external display2.to Verify if iMac video circuitry is functioning.If image appears on external display go toBacklight Issue/No Backlight symptom ow.
Reset SMC.3.
Deep Dive
Check Result Action CodeVerify boot chime present and1.fans running when systempowered ON. (Reset SMC andclear PRAM if necessary forproper boot up.)
Yes Power ON self test OK. Bootsequence started. Go to step 2.
No Go to Won’t Start Up
symptom ow.
Verify if image is visible on2.built-in LCD panel.
Yes Video present. Verify systemfunctionality and return touser or jump to appropriatetroubleshooting ow.
No Go to step 3.
Connect supported external3.display. Verify if image appearson external display whensystem is booted.
Yes External display detected bysystem. Video circuitry onlogic board functional. Go toBacklight Issue/No Backlight symptom ow.
No Go to step 4.
Pivot enclosure to access4.lower intake vent, and locatediagnostic LEDs on edge of
logic board. Verify if LED #3turns on shortly after systempowers on.
Yes Logic board communicatingwith video card. Go to step 5.
No If LED #3 does not turn ON-If system has a video card,reseat video card and retest,then replace video card andrepeat step 4. If issue persists,replace logic board.
-For a system without videocard, replace logic board.
M03
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 34/218
iMac (21.5-inch, Late 2009) Symptom Charts — Startup and Power 342009-11-24
Locate5. diagnostic LEDs onlogic board. Verify if LED #4turns on shortly after systempowers on.
Yes Logic board communicatingwith LCD panel. Go toBacklight Issue/No Backlight symptom ow.
No Replace LVDS cable.Go to step 6.
Locate6. diagnostic LEDs onthe logic board. Verify if LED #4turns on shortly after systempowers on.
Yes Video controller functionaland communicating with LCDpanel. Go to Backlight Issue/No Backlight symptom ow.
No Video controller unable tocommunicate with LCD panel.Replace LCD panel. Retest.
M03
Corrupted VideoUnlikely cause: power supply, hard drive, optical drive, fans, speakers, camera, microphone
Quick Check
Symptoms Quick Check
Corrupted Video Text and graphics appear fuzzy•Image corrupted•
Set System Preferences > Displays to native1.resolution of LCD. Non-native resolutions areunable to produce optimal clarity.
Clean outside surface of glass panel.2.
Make sure all relevant software updates have3.been applied. Graphics driver updates may beincluded with software updates.
Boot from install DVD or another known-good4.volume to determine whether a potentialsoftware/driver issue exists.
When issue occurs, take a screenshot of the5.display (Command-Shift-3). View screenshot leon a known-good computer. If image corruptioncan be seen in the screenshot then issue is withthe video drivers, software, or video/logic board. If
issue cannot be seen in the screenshot then LCDpanel and LVDS cable should be tested further.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 35/218
iMac (21.5-inch, Late 2009) Symptom Charts — Startup and Power 352009-11-24
Deep Dive
Check Result Action Code
Boot from Install DVD and1.Verify if issue is still visible.
Yes Go to step 2.
No Issue likely caused bysoftware or driver issue.
Troubleshoot for softwareissues. Make sure all softwareupdates have been installed.
Verify if issue is visible on an2.external display.
Yes Issue is NOT caused byinternal LCD display. Go to step 3.
No Go to step 6.
For systems without a separate3.video card, go to step 4. If avideo card is present, remove
video card, inspect connectorfor damage or corrosion.Reinstall video card and retest.Verify if issue still occurs.
Yes Replace video card. Go to step 4.
M04
No Issue resolved by reseatingvideo card.
Verify if video corruption issue4.is still present.
Yes Replace logic board. If a videocard was replaced, reinstallthe user’s original video card.Go to step 5.
M04
No Issue resolved withreplacement video card.
Verify if video corruption issue5.
is still present with replacementlogic board installed.
Yes Return to step 1 and retest. X04
No Issue resolved withreplacement logic board.
M04
Inspect glass panel. Verify if6.issue is caused by condensationor contaminants on inside/outside surface of glass panel,or on surface of LCD panel.
Yes Clean glass and/or LCD usingprocedures in Glass Paneltake-apart chapter.
Identify possible sourcesof contamination (nearbycigarette/cooking smoke,heavy airborne dust, etc.)to prevent recurrence.
Condensation shoulddissipate after computer hasbeen running a few hours.
No Go to step 7.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 36/218
iMac (21.5-inch, Late 2009) Symptom Charts — Startup and Power 362009-11-24
Disconnect LVDS cable7.between LCD display and logicboard, and verify if there isdamage to cable or connectors.Repeat with vertical sync cableconnected between LCD panel
and LED backlight board.
Yes Replace LVDS cable or anyother damaged part/module.
X03
No Reinstall LVDS cable andvertical sync cable. Go to step 8.
Verify if issue is still visible after8.reinstalling/replacing LVDScable and vertical sync cable.
Yes Replace LVDS cable and LCDpanel. Go to step 9.
L04
No Issue resolved with reseatingcables.
Verify if issue is still present9.with replacement LCD panelinstalled.
Yes Return to step 1 and retest.
No Issue resolved withreplacement of LCD panel.
L04
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 37/218
iMac (21.5-inch, Late 2009) Symptom Charts — Startup and Power 372009-11-24
Burnt Smell/Odor
Unlikely cause: speakers, microphone, rear housing
Quick Check
Symptoms Quick Check Burnt Smell/Odor
Burning smell•Unusual odor•
Verify that computer is the source of the odor.1.
If system is new, see2. kBase #TA22044: NewEquipment: Odors May Be Present Short-Term.
Disconnect all third-party devices and check to3.see if any external device is the source of odor.
Inspect air intake and air outlets for obstructions.4. To prevent overheating make sure thereis sucient clearance to allow air to owunobstructed into and out of the system.
Verify if system is functional.5.
Deep Dive
Check Result Action Code
Verify if source of the odor1.can be identied by visuallyinspecting each moduleand its associated cables forsigns of burned or damagedcomponents, smoke residue,
burned traces, or melted ordamaged wiring,
Yes Replace aected module(s).Go to step 2
P08
No Unable to locate source ofodor. Go to step 3.
Disconnect all third-party2.devices and cables. Power ONsystem and verify if smoke orstrong odor returns.
Yes Power down systemimmediately. Go to step 3.
No System functions correctly.Verify system functionalitywith third-party devices andcables and return systemto user if problem has beenresolved. Consult third-partycompanies as needed for
issues with those products.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 38/218
iMac (21.5-inch, Late 2009) Symptom Charts — Startup and Power 382009-11-24
Verify if source of odor can be3.located using your nose.
Yes Replace aected module(s)and retest system.
P08
No Contact Apple for assistanceif you feel that there is apossible safety issue withcomputer that has not beenresolved in previous steps.
Uncategorized Symptoms
Quick Check
Symptoms Quick Check
Uncategorized Symptoms
Unable to locate appropriate• symptom code.
Make sure system is plugged into a known-good1.
outlet.Listen for boot chime, fan, optical drive, or hard2.drive noise which indicates system is poweringup. If noise is heard, go to Won’t Start Up
symptom ow. If no noise is heard go toNo Power, Dead Unit symptom ow.
Attempt to boot from Install DVD to isolate3.possible software issues.
Deep Dive
Check Result Action CodeVerify if existing symptom code1.applies to issue reported byuser.
Yes Jump to appropriatesymptom code ow.
No Document reported failureand send feedback [email protected]
stating that a suitablesymptom code wasn’t found.Provide as much detail aspossible.
N99
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 39/218
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 40/218
iMac (21.5-inch, Late 2009) Symptom Charts — Display 402009-11-24
Shine bright (low heat)5.ashlight onto front of LCD.With computer powered ONverify if a faint image is visible.
Yes LCD panel functional butbacklight is missing ordim. Remove LCD paneland inspect and reseat thefollowing cable connections:
-Output cable between lower
end of LED backlight boardand lower end of LCD panel.
-Vertical sync cable betweenupper end of LED backlightboard and LCD panel.
-DC power cable betweenupper right of LED backlightboard and power supply.
Replace any damaged cable.Reinstall LCD panel and go tostep 6.
X03
No No image or backlight.Go to step 7.
Power ON system. Verify if6.image is now visible on LCDpanel with correct backlightlevel.
Yes Issue resolved.
No Replace LED backlight board.Retest. If issue persists, go tostep 7.
M04
Inspect and reseat7. LVDS cablebetween LCD panel and logicboard. Power ON system. Verifyif image is visible on built-inLCD display.
Yes Issue resolved.
No Replace LVDS cable.
If issue persists, replace LCDpanel. Retest.
X03
L03
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 41/218
iMac (21.5-inch, Late 2009) Symptom Charts — Display 412009-11-24
Noise / Unstable Flickering
Unlikely cause: camera, microphone
Quick Check
Symptoms Quick Check Noise / Unstable Flickering
Unstable image•Flickering image•Humming noise from display•High frequency noise from•display
Verify that intake vent on bottom of computer is1.not obstructed.
Inspect system for third party software that is2.being used to set fan speeds to a higher thannormal RPM. Some users may install this softwareto monitor and control internal temperatures,potentially causing higher fan speeds to generatehigher than expected noise levels.
Deep DiveCheck Result Action Code
Verify if user issue is due to1.ickering, or to an unstablevideo image on the LCD.
Yes Suspected ickering issue, goto step 2
No For audible noise issues go tostep 8. All other issues go toappropriate symptom ow.
Connect a supported external2.display to the mini DisplayPorton rear of computer. Verify
if issue occurs with externaldisplay.
Yes Suspect issue with videocircuitry. Go to CorruptedVideo symptom ow.
No Video circuitry OK.Go to step 3.
Disconnect and carefully3.inspect all four cables onback of LCD panel for signs ofdamage, corrosion, or pinchedwires.
Yes Replace damaged cable(s)where needed, otherwisereattach connectors. Retest.
X03
No Go to step 4.
Power ON computer and verify4.if issue still occurs.
Yes If connections are secure anddisplay is still ickering, go tostep 5.
No Issue resolved.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 42/218
iMac (21.5-inch, Late 2009) Symptom Charts — Display 422009-11-24
Shine bright (low heat)5.ashlight into front of LCD.Verify if an image is beingdisplayed when ickering issueis occurring.
Yes Image present but backlightis ickering. Replace verticalsync cable (between LCDpanel and upper end of LEDbacklight board) and retest.
If issue persists, replace LED
backlight board.
X03
M04
No Replace LVDS cable betweenLCD panel and logic board,and retest.
X03
Verify if noise varies when6.adjusting brightness level upand down.
Yes Noise seems to be generatedby LCD panel or backlightcircuitry. Go to step 7.
No Noise is from another source.Go to Noise/Hum/Vibration
symptom ow.
Verify if noise can be heard7.when computer is set up withuser seated in normal userposition. Adjusting brightnesslevel up and down may benecessary to recreate issue.
Yes Replace LED backlight board.Go to step 8.
M04
No Noises that are not audiblefrom the normal user positionare considered acceptable.
Verify if noise is still present.8. Yes Replace LCD panel. I f noisestill present, go to Noise/Hum/Vibration symptomow.
L06
No Issue resolved.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 43/218
iMac (21.5-inch, Late 2009) Symptom Charts — Display 432009-11-24
LCD Image Issues
Unlikely cause: power supply, hard drive, optical drive, fans, speakers, camera, microphone
Quick Check
Symptom Quick Check LCD Issues
Incorrect/missing colors•Distorted/blurred image•Pixel anomalies•Vertical/horizontal lines•Non-uniform brightness•
Allow display to reach normal operating1.temperature for about 15 minutes beforeevaluating front-of-screen performance.
Check display preferences for use of custom2.display prole.
Check brightness setting.3.
Clean glass panel while checking for dust/debris.4.
Deep Dive: GeneralCheck Result Action Code
Verify if issue is incorrect/1.missing colors.
Yes Go to incorrect/missingcolors.
No Go to step 2.
Verify if issue is distorted/2.blurred image.
Yes Go to distorted/blurredimage.
No Go to step 3.
Verify if issue is bright or dark3. pixel anomalies. Yes Go to pixel anomalies.No Go to step 4.
Verify if issue is vertical or4.horizontal lines.
Yes Go to vertical/horizontallines.
No Go to step 5.
Verify if issue is non-uniform5.brightness.
Yes Go to non-uniformbrightness.
No LCD functioning OK. Return toappropriate symptom ow if
user issue is still present.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 44/218
iMac (21.5-inch, Late 2009) Symptom Charts — Display 442009-11-24
Incorrect/Missing Colors
Unlikely cause: power supply, hard drive, optical drive, fans, speakers, camera, microphone
Quick Check
Symptoms Quick Check Incorrect/Missing Colors
Wrong color display•Color/contrast issues•
Allow display to reach normal operating1.temperature for about 15 minutes beforeevaluating front-of-screen performance.
Verify if System Preferences > Display settings are2.congured to use default display prole.
Verify System Preferences > Universal Access >3.Display “Enhance contrast”, “Use grayscale”, and“Black on White/White on Black” settings are setto defaults.
Deep Dive
Check Result Action Code
Verify computer has been1.warmed up for about 15minutes to stabilize backlightbefore continuing.
Yes Go to step 2.
No Warm up computer for about15 minutes. Go to step 2.
Verify if all four cables on back2.of LCD panel are secure at bothends.
Yes Go to step 3.
No Reseat connections, replacedamaged cable(s) if needed.Retest.
L14
Go to System Preferences >3.Desktop & Screen Saver >Desktop and set color to SolidGray Light. Verify if incorrect/missing color issue aectsentire display.
Yes Suspect poor videoconnection. Replace LVDScable between LCD panel andlogic board.
L14
No Go to step 4.
Set up computer side-by-side4.with a known-good, same-model computer showingsame image. Verify if issue is
noticeably worse on displaybeing tested.
Yes Replace LCD panel. L02
No Small variations in coloruniformity across display are
normal and do not warrantreplacement of LCD.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 45/218
iMac (21.5-inch, Late 2009) Symptom Charts — Display 452009-11-24
Distorted/Blurred Image
Unlikely cause: power supply, hard drive, optical drive, fans, speakers, camera, microphone
Quick Check
Symptoms Quick Check Distorted/Blurred Image
Text and graphics appear fuzzy•Image corrupted•
Set System Preferences > Displays to native1.resolution of LCD. Non-native resolutions areunable to produce optimal clarity.
Clean outside of glass panel.2.
Boot from install DVD to determine if a potential3.software issue exists.
Deep Dive
Check Result Action CodeBoot from Install DVD and1.verify if issue is still visible.
Yes Go to step 2.
No Issue likely caused bysoftware or driver issue.
Troubleshoot for softwareissues. Make sure all softwareupdates have been installed.
Verify if issue is visible on an2.external display attached tomini DisplayPort.
Yes Issue NOT caused by internalLCD panel. Go to step 3.
No Go to step 6.
For systems without video card,3.go to step 4. If a video card ispresent, remove video card,inspect connector for damageor corrosion then reinstall.Verify if issue still occurs.
Yes Replace video card.Go to step 4.
M24
No Issue likely caused by poorvideo card connection.
Verify if distorted/blurred4.image issue is still present.
Yes Replace logic board. Forsystems with a video card,reinstall the user’s originalvideo card. Go to step 5.
M04
No Issue resolved.
Verify if issue is still present5.with replacement logic boardinstalled.
Yes Return to step 1 and retest.
No Issue resolved.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 46/218
iMac (21.5-inch, Late 2009) Symptom Charts — Display 462009-11-24
Inspect glass panel. Verify if6.issue is caused by condensationor contaminants on insidesurface of glass panel.
Yes Clean glass and/or LCD usingprocedures in Glass Paneltake-apart chapter.
Identify possible sourcesof contamination (nearbycigarette/cooking smoke,
heavy airborne dust, etc.)to prevent recurrence.Condensation shoulddissipate after computer hasbeen running a few hours.
No Go to step 7.
Remove LVDS cable between7.LCD panel and logic board,and verify if there is damage tocable or connectors.
Yes Replace LVDS cable. X03
No Reinstall LVDS cable.Go to step 8.
Verify if issue is still visible after8. reinstalling LVDS cable. Yes Replace LCD panel.Go to step 9. L04
No Issue resolved.
Verify if issue is still present9.with replacement LCD panelinstalled.
Yes Return to step 1 and retest.
No Issue resolved.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 47/218
iMac (21.5-inch, Late 2009) Symptom Charts — Display 472009-11-24
Pixel Anomalies
Unlikely cause: logic board, power supply, hard drive, optical drive, fans, speakers, camera,microphone
Quick Check Symptoms Quick Check
Pixel AnomaliesDark dot anomalies•Bright dot anomalies•Debris on inside surface of•glass panelDebris on surface of LCD panel•
Clean outside surface of glass panel.1.
See2. kBase #HT1721: About LCD display pixelanomalies.
Deep Dive
Check Result Action Code
Determine if “defects” are dust/1.debris on surface of glass panelor LCD.
Yes Clean glass and/or LCD usingprocedures in Glass Paneltake-apart chapter.
No Go to step 2.
Determine if bright pixel2.defects exceed acceptablenumber. See kBase #HT1721:About LCD display pixelanomalies.
Yes Replace LCD panel. L08
No LCD panel meets bright pixeldefect specications.Go to step 3.
Determine if dark pixel defects3.exceed acceptable number. See kBase #HT1721: About LCDdisplay pixel anomalies.
Yes Replace LCD panel. L08
No LCD panel meets dark pixeldefect specications.Go to step 4.
Determine if combination4.of bright/dark pixel defectsexceed acceptable number. SeekBase #HT1721: About LCDdisplay pixel anomalies.
Yes Replace LCD panel. L08
No Explain to user that LCDpanel is operating withinspecications for pixel defects.Do NOT replace LCD panel.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 48/218
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 49/218
iMac (21.5-inch, Late 2009) Symptom Charts — Display 492009-11-24
Isolate with only one memory6.module installed, then with theother one. Test with known-good memory. Verify if issueonly happens with specicRAM module(s).
Yes Replace aected RAM
module.X02
No Go to step 7.
Isolate with one known-good7.memory module installed inone memory slot. Repeat bytesting in other memory slotsVerify if issue only happenswith specic memory slot oflogic board.
Yes Replace logic board andretest.
M07
No Go to step 8.
Remove LVDS cable between8.LCD panel and logic board andverify if there is damage tocable or connectors.
Yes Replace LVDS cable.Go to step 9.
X04
No Reinstall LVDS cable.Go to step 9.
Verify if issue is still present9.after reinstalling LVDS cable.
Yes Replace logic board. If videocard was present, reinstalloriginal video card.Go to step 10.
M04
No Issue resolved.
Verify if issue is still present10.with replacement logic boardinstalled.
Yes Go to step 11.
No Issue resolved.
Reinstall original logic board11.and verify if issue is still presentwith original logic boardreinstalled.
Yes Replace LCD panel. L04
No Issue resolved. If a video cardwas present, reinstall originalvideo card.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 50/218
iMac (21.5-inch, Late 2009) Symptom Charts — Display 502009-11-24
Non-Uniform Brightness
Unlikely cause: power supply, hard drive, optical drive, fans, speakers, camera, microphone
Quick Check
Symptoms Quick Check Non-Uniform Brightness
Brightness not uniform•Color not-uniform•
Verify System Preferences > Displays > Brightness1.slider is set above minimum.
Allow 15 minutes for backlight to reach normal2.operating temperature and output beforeevaluating display.
Visually inspect glass panel for presence of dust,3.cigarette smoke, or other contaminants. Cleanglass panel if needed.
Deep DiveCheck Result Action Code
Determine if brightness1.uniformity issue is visible afterdisplay has warmed up forabout 15 minutes.
Yes Go to step 2.
No Display backlight can takeseveral minutes to stabilize.Retest. If issue still not visiblereturn computer to user.
Look at user-provided2.examples showing brightnessuniformity issue. Determine if
variation in uniformity appearsexcessive when compared toanother same-model computer.
Yes Go to step 3.
No Demonstrate to user that LCDperforms similarly to anothercomputer of the same model.
Remove glass panel and3.loosen screws securing LCDpanel. Determine if brightnessuniformity improves.
Yes Inspect for mechanicalinterference with screwsor cables making contactwith back of LCD. Reseatcomponents & cables, retest.
No Go to step 4.
Remove LCD panel, then4.
inspect and reseat backlightcables. Determine if brightnessuniformity improves.
Yes One or more backlight cables
were loose.No Replace LCD panel. L07
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 51/218
iMac (21.5-inch, Late 2009) Symptom Charts — Display 512009-11-24
Cosmetic Defects
Symptoms Quick Check
Cosmetic Defects to LCDCracked LCD•Scratched LCD polarizer•Scorched or melted LCD•LCD impact damage•Foreign material on LCD or•back side of glass panel.
Determine if damage was caused by user1.environment, accidental damage, or abuse. Ifapplicable, inform user that Apple does notwarrant damage caused by accident, abuse,misuse, ood, re, earthquake, or other externalcauses. For more information, refer to:http://www.apple.com/legal/warranty
For dark and bright pixel anomalies see2.Pixel Anomalies symptom ow.
Uncategorized Symptoms
Quick Check
Symptoms Quick Check
Uncategorized SymptomsUnable to locate appropriate•symptom code.
Make sure brightness level is set above minimum.1.
Clean glass panel to make sure external2.contaminants are removed prior to evaluatingdisplay performance.
Allow LCD display to warm up approximately3.15 minutes before evaluating display color and
brightness uniformity performance.
Deep Dive
Check Result Action Code
Verify if existing symptom code1.applies to issue reported byuser.
Yes Jump to appropriatesymptom code ow.
No Document reported failureand send feedback [email protected]
stating that a suitablesymptom code wasn’t found.Provide as much detail aspossible.
N99
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 52/218
iMac (21.5-inch, Late 2009) Symptom Charts — Mass Storage 522009-11-24
Mass Storage
Hard Drive Not Recognized
Unlikely cause: LCD panel, power supply, fans, speakers, camera, microphone
Quick Check
Symptoms Quick Check
Drive Not RecognizedDrive No Boot
Flashing Question Mark •Boots to Grey Screen•Boots to Blue Screen•Boots to Prohibitory Symbol•
(Review kBase #HT2674: Intel-based Mac: Startup sequenceand error codes, symbols)
Use a known-good mouse. A stuck mouse button1.will not allow boot.
Boot from Install DVD. Use Disk Utility to verify2.S.M.A.R.T. status of hard drive.
Use Disk Utility to repair disk.3.
Verify that user’s data is backed up and that user4. authorizes erasing disk and reinstalling software.
Use Target Disk Mode to mount user’s hard drive5.on a known-good computer. Use Disk Utility onhost computer for Quick Checks 2 through 4.
Deep Dive
Check Result Action Code
Boot from Install DVD and run1.
Disk Utility. Verify if user’s harddrive is available for Disk Utilityto repair.
Yes Go to step 2.
No Go to step 5.
Run Disk Utility’s “Repair2.Disk” function and verify if itcompletes successfully.
Yes Go to step 3.
No Go to step 4.
Reboot computer. Verify if3.system boots successfully andthat Disk Utility “Verify” functionreports no errors.
Yes Data error. Issue resolved. H07
No Go to step 4.
With user’s permission, erase4.
hard drive and reinstall MacOS. Verify if installation processcompletes.
Yes Go to step 8.
No Go to step 5.
Inspect hard drive SATA and5.power cables and connectorsfor bent pins, or other damageto the cable.
Yes Replace damaged SATA cableor DC power cable. Go to step 8.
X03
No Go to step 6.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 53/218
iMac (21.5-inch, Late 2009) Symptom Charts — Mass Storage 532009-11-24
Reseat hard drive SATA cable6.at logic board and hard driveconnections, and verify ifcomputer starts up.
Yes Go to step 8.
No Replace SATA cable. Go to step 8.
X03
Test with known-good7.bootable hard drive. Verify ifsystem boots successfully andthat Disk Utility “Verify” functionreports no errors.
Yes Install user ’s hard drive. Go to step 9.
No SATA cable veried orreplaced and known-goodhard drive installed. Replacelogic board. Go to step 1.
Reboot computer. Verify if8.system boots successfully andthat Disk Utility “Verify” functionreports no errors.
Yes Issue resolved. Return systemto user.
No Go to step 7.
Reboot computer. Verify if9.system boots successfully and
that Disk Utility “Verify” functionreports no errors.
Yes Issue resolved.
No User ’s hard drive appears tobe defective. Go to step 10.
Replace hard drive. Boot from10.system-specic Install DVDand reinstall Mac OS X withdrive format option. Verify ifdrive is formatted correctly(GUID partition table) and thatsoftware restore was successful.
Yes Issue resolved by replacinghard drive.
H01
No SATA cable veried/replacedand new hard drive installed,Check with known-goodrestore DVD. If restore failurestill happens, go to step 11.
If restore is unsuccessful,11.startup a known-good systemin Target Disk Mode andconnect it to the user’s systemwith a FireWire cable. Onceset up, insert the iMac InstallDisc in its optical drive. Startupuser’s system while holdingOption key, select and bootfrom the Install Disc DVDand restore system software.Verify if software restore wassuccessful.
Yes Restore failure seems to bedue to internal optical driveor media issue. Go to OpticalDrive Read/Write Error
symptom ow.
No Restore failure seems to bedue to internal SATA busissue. Replace logic board.
M19
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 54/218
iMac (21.5-inch, Late 2009) Symptom Charts — Mass Storage 542009-11-24
Hard Drive Read/Write Errors
Unlikely cause: LCD panel, power supply, fans, speakers, camera, microphone
Quick Check
Symptoms Quick Check Drive Read/Write ErrorDrive Bad Sector/DefectiveDrive Formatting Issues
Cannot save documents•Read/write error message•Hang when accessing or saving•data
Boot from Install DVD. Use Disk Utility to verify1.S.M.A.R.T. status of hard drive.
Use Disk Utility to repair disk.2.
Verify that user’s data is backed up and that user3.authorizes erasing disk and reinstalling software.
Use Target Disk Mode to mount user’s hard drive4.on a known-good computer. Use Disk Utility onhost computer for Quick Checks 2 through 3.
Deep Dive
Check Result Action Code
Run Disk Utility ‘Repair Disk’1.function and verify if itcompletes successfully.
Yes Go to step 2.
No Go to step 3.
Reboot computer. Verify if2.system boots successfully andthat Disk Utility “Verify” functionreports no errors.
Yes Data error. Issue resolved. H07
No Go to step 3.
With user’s permission, erase3. hard drive and reinstall MacOS. Verify if installation processcompletes.
Yes Go to step 6.
No Go to step 4.
Inspect hard drive SATA, power4.cables and connectors for bentpins, or other damage to thecable.
Yes Replace damaged cable. Go to step 6.
H04
No Go to step 5.
Reseat SATA cable on hard5.drive and logic board. Verify ifcomputer starts up.
Yes Go to step 6.
No Replace hard drive data cable. Go to step 6.
H04
Reboot computer. Verify if6.system boots successfully andDisk Utility “Verify” functionreports no errors.
Yes Issue resolved.
No Go to step 7.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 55/218
iMac (21.5-inch, Late 2009) Symptom Charts — Mass Storage 552009-11-24
Test with known-good hard7.drive. Verify if system bootssuccessfully and Disk Utility“Verify” function reports noerrors.
Yes Reinstall user’s hard drive, goto step 8.
No SATA cable veried orreplaced and known-goodhard drive installed. Replacelogic board.
Reboot computer. Verify if8.system boots successfully andthat Disk Utility “Verify” functionreports no errors.
Yes Issue resolved.
No User ’s hard drive appears tobe defective. Go to step 9.
Replace user’s hard drive. Verify9.if drive formats correctly with aGUID partition map and installsMac OS without errors.
Yes Issue resolved by replacinguser’s hard drive.
H03
No SATA cable veried orreplaced and new hard drivedid not resolve issue. Replacelogic board.
M19
Hard Drive Noisy
Unlikely cause: LCD panel, logic board, power supply, speakers, camera, microphone
Quick Check
Symptoms Quick Check
Hard Drive Noisy
Noise during start up•Noise during operation•Noise when drive is copying or•saving data
Boot from Install DVD. Use Disk Utility to verify1.
S.M.A.R.T. status of hard drive.Use Disk Utility to repair disk.2.
Determine if noise is comparable to another3.machine of the same model.
Deep Dive
Check Result Action Code
Boot from the Install DVD and1.run Disk Utility. Verify if user
hard drive is available for DiskUtility to repair.
Yes Go to step 2.
No Go to Hard Drive NotRecognized symptom ow.
Run Disk Utility ‘Repair Disk’2.function and verify if itcompletes successfully.
Yes Go to step 3.
No Go to step 4.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 56/218
iMac (21.5-inch, Late 2009) Symptom Charts — Mass Storage 562009-11-24
Restart the computer. Verify if3.the noise is still present.
Yes Go to step 4.
No Issue resolved. Return systemto user.
H06
With user’s permission, erase4.hard drive and reinstall Mac
OS. Verify if installation processcompletes.
Yes Go to step 3.
No Replace hard drive. Go to step 5.
With replacement hard drive5.installed, reboot computer.Verify if noise is still present.
Yes Replacement hard drive didnot resolve issue. Go to step 6.
No Issue resolved by replacinghard drive.
H06
With hard drive removed verify6.if rubber vibration isolationgrommets are properlyinstalled in hard drive bracket
(attached to hard drive) andto mechanism in rear housing(where hard drive pins insert).
Yes Go to step 8.
No If grommets are missing ordamaged, replace hard drive
bracket or mechanism asappropriate. Go to step 7.
Reboot computer. Verify if noise7.is still present.
Yes Go to step 8.
No Issue resolved. Returncomputer to user.
H06
Disconnect hard drive SATA and8.power connections then bootfrom the Install DVD. Verify ifnoise is caused by fans.
Yes Go to Fan Failures/ThermalIssues symptom ow.
No Go to step 9.
Disconnect hard drive and9. optical drive then boot from anexternal volume. Verify if noisedisappears when optical drivehas been disconnected.
Yes Possible optical drive ormedia issue. Go to OpticalDrive Noisy symptom ow.
No Noise issue still present, butdoes not appear to be causedby hard drive. Go to Noise/Hum/Vibration symptomow.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 57/218
iMac (21.5-inch, Late 2009) Symptom Charts — Mass Storage 572009-11-24
Optical Drive Not Recognized
Unlikely cause: LCD panel, power supply, fans, speakers, camera, microphone
Quick Check
Symptoms Quick Check Drive Not Recognized/Mount
Discs inject and eject, but do•not appear in Finder
Use System Proler Serial-ATA section to see if1.optical drive appears.
System Proler Serial-ATA section will show any2.media inserted.
Check Finder Preferences and make sure “CD’s,3.DVD’s and iPods” is checked under “Show theseitems on the desktop” in the General section.
Deep Dive
Check Result Action Code
Verify if optical drive is listed1.in Serial-ATA section of SystemProler.
Yes Go to step 2.
No Go to step 3.
Test both CD and DVD media.2.Verify if optical drive can readboth CD and DVD media.
Yes No issue, or possibleintermittent issue. Gathermore information from user.
No If both types of media fail,check that Finder Preferencesare set to “show CD’s andDVD’s”, then go to step 3.
If only one type of media fails,drive has a laser pickup issue.Replace optical drive.
J03
Connect known-good optical3.drive to SATA cable. Verify ifboth CD and DVD media areread reliably.
Yes SATA cable and port on logicboard good. Go to step 5.
No Go to step 4.
Reseat SATA cable connections4.at optical drive and logic board
(cable connects to back of logicboard). Verify if both CD andDVD media are read reliably.
Yes Go to step 6.
No Replace SATA cable and test.
If issue persists, replace logicboard.
Go to step 6.
X03
M19
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 58/218
iMac (21.5-inch, Late 2009) Symptom Charts — Mass Storage 582009-11-24
Connect original optical drive5.to known-good SATA cable.Verify if both CD and DVDmedia are read reliably.
Yes SATA cable issue. ReplaceSATA cable. Go to step 6.
X03
No Replace optical drive. J03
Test read compatible known-6.good CD and DVD media(Install DVD). Verify if media isrecognized and reads reliably.
Yes Issue resolved.
No Replace optical drive. J03
Optical Drive Won’t Accept/Eject Media
Unlikely cause: LCD panel, power supply, fans, speakers, camera, microphone
Quick Check
Symptoms Quick Check Drive Won’t Accept MediaDrive Won’t Eject Media
Cannot insert a disc into drive•Cannot eject a disc from drive•
Use System Proler Serial-ATA section to see if1.optical drive appears. If not, go to Optical DriveNot Recognized symptom ow.
Restart computer and hold down mouse button2.or keyboard eject key to cycle optical drive.
Inspect optical drive slot for obstructions3.
Deep Dive
Check Result Action CodeVerify if optical drive is listed in1.System Proler device tree forSerial-ATA devices.
Yes Optical drive communicatingwith logic board. Go to step 5.
No Go to step 2.
Verify SATA cable connections2.between optical drive and logicboard. Visually inspect cablesand connectors for any debris,damage or bent pins. Verify ifoptical drive is listed in SystemProler device tree.
Yes Optical drive communicatingwith logic board. Go to step 5.
No Replace damaged cablesand retest. If connections aregood and no visible cabledamage, go to step 3.
X03
Connect known-good optical3.drive to SATA cable. Verify ifknown-good optical drive islisted in the System Prolerdevice tree.
Yes Go to step 4.
No Suspect bad SATA cable. Go to step 7.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 59/218
iMac (21.5-inch, Late 2009) Symptom Charts — Mass Storage 592009-11-24
With known-good optical drive4.installed, test for media inject/eject. Verify if drive accepts andejects known-good media.
Yes Known-good optical driveresolved inject/eject issue.Replace optical drive.
J03
No Go to step 7.
Inspect optical drive slot during5.
disc insert/eject. Verify if discscan be inserted easily.
Yes Go to step 6.
No Verify correct optical drivebezel alignment withenclosure. Reseat optical drivethen retest. If issue persists,replace optical drive.
J03
With known-good optical6.media (Install DVD), test formedia inject/eject. Verifyif drive accepts and ejectsknown-good media.
Yes Media issue. No repairnecessary. Suggest userinvestigate use of dierentmedia.
No Go to step 3.
Replace SATA cable then test7.for media inject/eject. Verify ifdrive injects and ejects known-good media.
Yes SATA cable resolved issue.Return system to user.
X03
No SATA cable veried orreplaced, and optical driveveried or replaced. Replacelogic board and retest.
M19
Optical Drive Read/Write Error
Unlikely cause: LCD panel, power supply, fans, speakers, camera, microphone
Quick Check
Symptoms Quick Check
Drive Read/Write Data ErrorErrors when writing optical•media.Errors when reading optical•media.Hang when accessing or•preparing to write data.
Test optical media in a known-good optical drive1.in the same type of computer to rule out mediaissue.
Check with known-good discs like the Install DVD2.that came with the computer.
For write issues, check with known-good media3.that performs well in a known-good optical drivein the same type of computer.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 60/218
iMac (21.5-inch, Late 2009) Symptom Charts — Mass Storage 602009-11-24
Deep Dive
Check Result Action Code
Verify if media is free to spin1.without optical drive scrapingedge or surface of media.
Yes Go to step 2.
No Replace optical drive. J05
Test both CD and DVD media.2.Verify if drive can read both CDand DVD media.
Yes Go to step 6.
No If both types of media fail,check that Finder Preferencesare set to “show CD’s andDVD’s”, then go to step 3.
If only one type of media fails,drive has a laser pickup issue.Replace optical drive.
J03
Connect known-good optical3.drive to SATA cable. Verify ifboth CD and DVD media areread reliably.
Yes SATA cable and port on logicboard good. Go to step 5.
No Go to step 4.
Reseat SATA cable connections4.at optical drive and logic board(cable connects to back of logicboard). Verify if both CD andDVD media are read reliably.
Yes Go to step 6.
No Replace SATA cable and test.
If issue persists, replace logicboard.
Go to step 6.
X03
M19
Connect original optical drive5.to known-good SATA cable.Verify if both CD and DVD
media are read reliably.
Yes SATA cable issue. ReplaceSATA cable. Go to step 6.
X03
No Replace optical drive. J03
Test write data to compatible6.CD and DVD media. Verify ifburned media is recognizedand read reliably.
Yes Issue resolved.
No Run ODD sensor and ODD fantests in ASD:
If errors found checkODD sensor and ODD fanconnections to logic board(read/write errors may be dueto drive being too hot).
If no errors are found while
running diagnostics, replaceoptical drive.
J03
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 61/218
iMac (21.5-inch, Late 2009) Symptom Charts — Mass Storage 612009-11-24
Optical Drive Not Performing to Specications
Unlikely cause: LCD panel, power supply, fans, speakers, camera, microphone
Quick Check
Symptoms Quick Check Optical Drive Not Performing toSpecications
Read or write speeds slower•than expected
Test optical media in another computer of the1.same type to rule out media issue.
For write issues, check with known-good media2.that performs well in another computer and driveof the same type.
Deep Dive
Check Result Action Code
Test both CD and DVD media.1. Verify if optical drive can readboth CD and DVD media.
Yes Go to step 5.No If both types of media fail,
check that Finder Preferencesare set to “show CD’s andDVD’s”, then go to step 2.
If only one type of media fails,drive has a laser pickup issue.Replace optical drive.
J03
Connect known-good optical2.drive to SATA cable. Verify ifboth CD and DVD media are
read reliably.
Yes SATA cable and port on logicboard good. Go to step 4.
No Go to step 3.
Reseat SATA cable connections3.at optical drive and logic board(cable connects to back of logicboard). Verify if both CD andDVD media are read reliably.
Yes Go to step 5.
No Replace SATA cable and test.
If issue persists, replace logicboard.
Go to step 5.
X03
M19
Connect original optical drive4.to known-good SATA cable.Verify if both CD and DVD
media are read reliably.
Yes SATA cable issue. ReplaceSATA cable. Go to step 5.
X03
No Replace optical drive. J03 Test write data to compatible5.CD and DVD media. Verify ifburned media is recognizedand read reliably.
Yes Issue resolved.
No Go to step 6.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 62/218
iMac (21.5-inch, Late 2009) Symptom Charts — Mass Storage 622009-11-24
Media that is out of balance6.may not perform well at higherspeeds even though higherspeeds may be supportedby the optical drive. Verify ifslowing requested burn speed
allows discs to be writtenreliably.
Yes Media issue. No repairnecessary.
No Go to step 7.
Test write data to compatible7.CD and DVD media. Verifyburned media is recognizedand reads reliably.
Yes Issue resolved.
No Run ODD sensor and ODD fantests in ASD:
If errors found checkODD sensor and ODD fanconnections to logic board(read/write errors may be dueto drive being too hot).
If no errors are found whilerunning diagnostics, replaceoptical drive.
J03
Optical Drive Noisy
Unlikely cause: LCD panel, power supply, fans, speakers, camera, microphone
Quick Check
Symptoms Quick Check
Optical Drive Noisy (J04)Noise during boot•Noise during operation•Noise when drive is copying or•writing data
Test optical media in another computer of the1.same type to rule out media issue.
Check with known-good discs like the Install DVD2.that came with the computer.
Verify if noise occurs without media in optical3.drive. If so, verify if noise made by hard drive orfans.
Deep Dive
Check Result Action Code
Test optical drive with dierent1.source of media. Does the noiseissue remain?
Yes Go to step 2.
No Issue due to unbalancedmedia. Recommend usingdierent media.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 63/218
iMac (21.5-inch, Late 2009) Symptom Charts — Mass Storage 632009-11-24
Reseat optical drive in2.enclosure. Does noise issueremain?
Yes Go to step 3.
No Issue resolved by reseatingdrive in enclosure.
Install known-good optical3.drive in enclosure. Does noise
issue remain?
Yes Go to step 4.
No Replace optical drive. J04
Compare system with similar4.model for optical drive noise inoperation and verify that noiselevel is similar.
Yes Noise level of opticaldrive appears to be withinspecication. Return systemto user.
No Check for other causes ofnoise in the system.
SD Card Will Not Insert Into SlotUnlikely cause: LCD panel, logic board, optical drive, hard drive
Quick Check
Symptom Quick Check
SD Card will not insert into slotSD Memory Card does not fully•seat into slotCard slot does not align with•
enclosure.
The SD card must be a 32 mm by 24 mm by 2.11.mm. You can also use thinner cards, such as MultiMedia Cards (MMC).
Clear any obstruction in SD card slot.2.
Deep Dive
Check Result Action Code
Verify if known-good SD card1.ts in slot.
Yes Ask user to replace defectiveor out-of-spec SD card.
No Loosen the SD board screws,then insert known-good SDcard again. Go to step 2.
Verify if known-good SD card2.now ts in slot.
Yes Tighten SD board screws. Go to step 3.
No Replace SD board and retest. M17
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 64/218
iMac (21.5-inch, Late 2009) Symptom Charts — Mass Storage 642009-11-24
Verify if SD card now ejects3.and inserts without issue.
Yes Issue resolved by SD boardalignment.
No Replace SD board. M17
SD Card Not Recognized
Unlikely cause: LCD panel, logic board, optical drive, hard drive
Quick Check
Symptom Quick Check
SD Card Not RecognizedCard does not show up on•desktop or in System Proler
Insert user’s SD card into a known-good system1.and verify that it functions properly. If cardcannot be read, contact card manufacturer for
support options.Verify SD card slot with known-good SD card.2.
Check correct drivers are installed for user’s SD3.card type. Standard SD cards are supported byMac OS X, but others may require specic driversoftware to be used.
Deep Dive
Check Result Action Code
Verify if SD card inserts1.correctly in SD slot.
Yes Go to step 2.
No Go to SD Card Will Not Insert Into Slot symptom ow.
Unlock and insert user’s SD2.card and verify it shows up ondesktop or in System Proler.
Yes Go to step 6.
No Go to step 3.
Insert a known-good unlocked3.SD card and verify if read/writecapabilities are working.
Yes User’s SD card not functioningproperly. Contact cardmanufacturer for support.
No Go to step 4.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 65/218
iMac (21.5-inch, Late 2009) Symptom Charts — Mass Storage 652009-11-24
Run System Proler and verify4.if SD card reader is now listedin USB devices.
Yes Go to step 5.
No Reseat SD cable at SD boardand logic board
If issue persists, replace
SD cable.
If issue persists, replace
SD board.
If issue persists, replace
logic board.
M17M17M17
Verify if a known-good5.unlocked SD card can now becorrectly read and written.
Yes Go to step 6.
No Replace SD board. M17
Lock the user’s SD card and6.verify if it can’t be written.
Yes Issue resolved.
No Replace SD board. M17
Uncategorized Symptoms
Check Result Action Code
Verify if existing symptom code1.applies to issue reported byuser.
Yes Jump to appropriatesymptom code ow.
No Document reported failureand send feedback to
[email protected] stating that a suitablesymptom code wasn’t found.Provide as much detail aspossible.
N99
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 66/218
iMac (21.5-inch, Late 2009) Symptom Charts — Communications 662009-11-24
Communications
AirPort/Bluetooth Issues
Quick Check
Symptoms Quick Check
AirPort/Bluetooth IssuesUnable to join networks or pair•devicesAirPort card not available•Intermittent device or•connection dropoutsLimited wireless range•
Verify that AirPort or Bluetooth is turned ON, and1.for AirPort issues make sure that a network isselected.
For AirPort, check if the wireless access point2.requires special connection and encryptionprotocols.
Check for nearby sources of interference such3.as microwave ovens or cordless phones. SeekBase #HT1365: AirPort: Potential source ofinterference.
Check the number of users trying to use AirPort4.in the area for possible network congestion(available bandwidth).
Isolate potential OS issues by starting up5.from original Install media for the computer, asame-model computer in Target Disk Mode, orcompatible known-good OS on an external drive.Both AirPort and Bluetooth services are availablewhen booted from Install disc.
Deep Dive
Check Result Action Code
Open System Proler. AirPort1.is listed under Network, whileBluetooth is listed under USB.Verify if both AirPort andBluetooth cards are recognized.
Yes Install all software updatesfor AirPort/Bluetooth andre-test. If issue persists aftersoftware update, go to step 4for AirPort, or go to step 6 forBluetooth.
No Go to step 2 for AirPort.Go to step 6 for Bluetooth. M11
Reseat both AirPort cable2.connection on logic board andon AirPort card carrier ends.Verify if AirPort card is nowlisted in System Proler.
Yes Issue resolved by reaseatingAirPort cable.
No Replace AirPort cable and re-test. Go to step 3.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 67/218
iMac (21.5-inch, Late 2009) Symptom Charts — Communications 672009-11-24
After cable has been replaced,3.verify if AirPort card is nowlisted in System Proler.
Yes Issue resolved by replacingAirPort cable.
X03
No Replace AirPort card carrierboard and re-test. If issuepersists (card not seen onbus), replace AirPort card.
M11
Enable AirPort and verify if4.known local AirPort networksare available, or create acomputer-to-computernetwork with anotherMacintosh computer usingAirPort. See http://docs.info.apple.com/article.html?path=AirPort/5.0/en/ap2110.html. Verify if youconnect successfully.
Yes Issue resolved.
No Go to step 5.
Check and reseat the two5.antennas to the AirPort card.Verify if you can connect toknown AirPort network.
Yes Issue resolved.
No Replace AirPort card. If issuepersists, replace AirPortantenna(s). If damagedantenna is the one embeddedin rear housing behind Applelogo, replace rear housing.
N04
Verify that computer and6.Bluetooth device are both indiscoverable mode. Verify ifyou can now successfully and
reliably pair the device.
Yes Issue resolved.
No Replace Bluetooth antenna.Go to step 7.
M11
Re-test with new Bluetooth7.antenna and verify if Bluetoothissues are resolved.
Yes Issue resolved.
No Replace Bluetooth card. M11
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 68/218
iMac (21.5-inch, Late 2009) Symptom Charts — Communications 682009-11-24
AirPort Card Kernel Panic
Quick Check
Symptoms Quick Check
AirPort Card Kernel PanicKernel Panic on startup•Kernel Panic or freezing while•attempting to connect to WiFinetworksKernel Panic while transferring•data on WiFi networks
Isolate OS by starting up from original Install1. media for this computer, a same-model computerin Target Disk Mode, or compatible known-goodOS on an external drive. AirPort and Bluetoothservices are available when booted from theInstall disk.
Ensure that all software and rmware updates for2.the computer and AirPort been installed.
Deep Dive
Check Result Action CodeDisconnect AirPort card cable1.end from logic board. Verify ifcomputer starts now withoutkernel panic.
Yes Reseat AirPort card cable andretest. If problem continuesreplace cable. Go to step 2.
No Kernel panic not relatedto AirPort. Restart fromInstall DVD or known-goodbootable external drive andcheck Panic.Log le on user’shard drive to nd out whichis the crashing I/O interface.Also troubleshoot installedMac OS X software..
With replacement AirPort2.card cable installed, verify ifcomputer starts now withoutkernel panic.
Yes AirPort cable issue. Issueresolved.
N13
No Replace AirPort card carrierboard and re-test. If issueremains, replace AirPort card.Go to step 3.
With replacement AirPort3.carrier or card installed, verifyif computer starts now without
kernel panic.
Yes AirPort carrier or card issue.Issue resolved.
N13
No Replace logic board. M11
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 69/218
iMac (21.5-inch, Late 2009) Symptom Charts — Communications 692009-11-24
Ethernet Port/Device Issue
Unlikely cause: LCD display, power supply, hard drive, optical drive, fans
Quick Check
Symptoms Quick Check Ethernet Port/Device Issue
No Ethernet device present•Unable to access network•resourcesEthernet device shows no•connectionEthernet device unable to an IP•addressSlow network performance•
Verify if Ethernet cable is inserted into port1.correctly. Check Ethernet cable for damage. Trya known good Ethernet cable – CAT5 or betterrecommended for 100Mbps+ connections.
Check Ethernet ports on the computer and wall/2.switch for dust, debris, damage or bent pins.
Ensure distance from networking infrastructure is3.less than 300 feet/ 105 meters.
Verify port, cable and network hardware with a4.known good system. Isolate rewall, MAC addressltering or hardware access control devices.
Isolate OS by starting up from original Install5.media for this computer, a same-model computerin Target Disk Mode, or compatible known-goodOS on an external drive.
Deep Dive
Check Result Action Code
Visually inspect Ethernet port1.
of computer and ensure that allpins will make physical contactwith the Ethernet cable.
Yes Go to step 2.
No Pins are damaged, bent at ormissing. Replace logic board.
M24
Boot from original Install media.2.Verify Network Link status isactive by using Network Utilityunder the “Info” tab. Verify if theLink Status is “Active”.
Yes Go to step 3.
No If same Ethernet cable givesan “Active” link status on aknown-good, same-modelcomputer, replace logic board.
M10
Connect computer to another3.Mac using CAT5 Ethernetcable. See article http://
docs.info.apple.com/article.html?path=Mac/10.5/en/8429.html. Verify if you connectsuccessfully.
Yes Ethernet communicationgood. Go to step 4.
No If same Ethernet cable andcomputer connects to aknown-good, same-modelcomputer, replace logic board.
M10
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 70/218
iMac (21.5-inch, Late 2009) Symptom Charts — Communications 702009-11-24
Check for speed and duplex4.issues on network. OpenSystem Preference > Network;click the Advanced button,then the Ethernet tab. Verify ifthe speed and duplex reported
are what is expected.
Yes Go to step 5.
No Change speed and duplexsettings. See article http://docs.info.apple.com/article.html?path=Mac/10.5/en/8711.html. Go to step 6.
Check for MTU (Maximum5. Transmission Unit) issues. SeekBase #HT2532: Mac OS X:How to change the MTU fortroubleshooting purposes.Verify if changing MTU settingson computer resolves issue.
Yes Go to step 6.
No Ethernet controller damaged.Replace logic board.
M10
If changing speed, duplex6.or MTU settings allowsconnectivity, check with aknown-good, same-modelcomputer. Verify if known-goodcomputer produces the sameresults.
Yes Check with ISP or NetworkAdministrator concerningspeed, duplex & MTU settings.
No Verify with known good OS.If issue persists, replace logicboard.
M10
Wireless Input Device Doesn’t Pair
Quick Check
Symptoms Quick Check
Wireless Input Device Doesn’tPair
Can’t get system to recognize•Bluetooth keyboard or mouse
Remove and reinstall batteries for device.1.
Check that device is powering on.2.
Use known-good batteries with device.3.
Ensure that device is being used within 30-foot4.range for Bluetooth devices.
Ensure that the latest Software Updates have5.been applied.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 71/218
iMac (21.5-inch, Late 2009) Symptom Charts — Communications 712009-11-24
Deep Dive
Check Result Action Code
Without any wired input1.devices connected, and with awireless mouse in discoverablemode, startup computer. Verifyif computer shows BluetoothMouse Setup Assistant.
Yes Bluetooth hardware is active.Go to step 6.
No Go to step 2.
Connect a wired mouse and2.run System Proler. Verify ifBluetooth interface is listedunder USB in System Proler.
Yes Bluetooth hardware ispresent. Go to step 6.
No Remove glass and LCD panel,reseat both ends of cablebetween Bluetooth board andlogic board. Go to step 3.
Use an external monitor.3.Run System Proler. Verify if
Bluetooth interface is listedunder USB in System Proler.
Yes Bluetooth hardware is nowpresent. Go to step 6.
No Replace Bluetooth cable.Go to step 4.
X03
Run System Proler. Verify if4.Bluetooth interface is listedunder USB in System Proler.
Yes Bluetooth hardware is nowpresent. Go to step 6.
No Replace Bluetooth board.Go to step 5.
M11
Run System Proler. Verify if5.Bluetooth interface is listedunder USB in System Proler.
Yes Bluetooth hardware is nowpresent. Go to step 6.
No Replace logic board. M11
Run Software Update and6.apply any available Bluetoothupdates. Activate Bluetoothin System Preferences (orApple menu icon) then select“Congure a new Bluetoothdevice” (or run BluetoothMouse Setup Assistant). Verify ifBluetooth mouse is seen.
Yes Bluetooth discovery is nowactive. Go to step 7.
No Replace Bluetooth antenna. X03
With a wireless mouse on, and7.in discoverable mode, verify
if you can successfully pairmouse with the assistant.
Yes Check for stability.Go to step 8.
No Go to Wireless Input DeviceLoses Connection symptomow.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 72/218
iMac (21.5-inch, Late 2009) Symptom Charts — Communications 722009-11-24
With wireless mouse paired,8.verify if mouse stays connected.
Yes Issue resolved.
No Inspect and reseat Bluetoothantenna cable. Replace adamaged antenna cable, orBluetooth board if its antennaconnector is damaged.
Go to step 9.
With wireless mouse paired,9.verify if mouse stays connected.
Yes Antenna issue. Issue resolved.
No Go to Wireless Input DeviceLoses Connection symptomow.
Wireless Input Device Loses Connection
Quick Check Symptoms Quick Check
Wireless Input Device LosesConnection
Wireless keyboard, mouse, or•other wireless input deviceloses connection.
Remove and reinstall batteries for device.1.
Check that device is powering on.2.
Use known-good batteries with device.3.
Ensure other devices pair and keep connection4.without issue. If not, see AirPort/BluetoothIssues symptom ow.
Ensure that device is being used within 30-foot5.
range for Bluetooth devices.Ensure that the latest Software Updates have6.been applied.
Deep Dive
Check Result Action Code
Open System Preferences >1.Bluetooth. Paired items andtheir connection status are
shown. Verify if device is listed.
Yes Device has been paired.Go to step 2.
No Device is not paired. Makedevice discoverable and openBluetooth Setup Assistant.Go to step 3.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 73/218
iMac (21.5-inch, Late 2009) Symptom Charts — Communications 732009-11-24
Make sure device is on.2.In System Preferences >Bluetooth, select device andfrom the Action menu (gear)choose “Connect”. Verify ifdevice connects successfully.
Yes Go to step 7.
No Delete pairing in SystemPreferences. Go to step 3.
With the device on, run3.Bluetooth Setup Assistant.Verify if you can successfullypair the device.
Yes Go to step 7.
No Restart computer.Go to step 4.
With device on, run Bluetooth4.Setup Assistant. Verify if youcan successfully pair device.
Yes Go to step 7.
No Create a new Admin User.Go to step 5.
Log into new Admin User5.account. With device on, runBluetooth Setup Assistant.
Verify if you can successfullypair device with new useraccount.
Yes User account issue. Troubleshoot software onUser account. No hardware
repair needed.No Remove the following le: /
Library/Preferences/com.apple.Bluetooth.plist Go to step 6.
Restart computer, With device6.on, run Bluetooth SetupAssistant. Verify if you cansuccessfully pair device.
Yes Go to step 7.
No Go to AirPort/BluetoothIssues symptom ow.
With device paired and7.connected, verify if deviceconnection is stable if usednormally.
Yes Issue resolved.
No Check wireless device manualto verify if device is beingused in accordance withmanufacturer’s specications(range, OS support, batterytypes). Go to step 8.
Verify if device is performing to8.stated specications.
Yes Educate user. Issue resolved.
No Replace wireless device.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 74/218
iMac (21.5-inch, Late 2009) Symptom Charts — Communications 742009-11-24
Uncategorized Symptoms
Quick Check
Symptoms Quick Check
Uncategorized SymptomsUnable to locate appropriate•symptom code.
Verify System Preferences/Network settings1. are congured appropriately to supportcommunication method.
For Ethernet connection issues verify that cable2.being used functions when used with anotherknown-good system.
For wireless connection issues review user3.environment to determine whether possibleinterference from other 2.4GHz or 5GHzcommunications devices might be contributingto issue. See kBase #HT1365: AirPort: Potentialsources of interference
Deep Dive
Check Result Action Code
Verify if existing symptom code1.applies to issue reported byuser.
Yes Jump to appropriatesymptom code ow.
No Document reported failureand send feedback [email protected]
stating that a suitablesymptom code wasn’t found.Provide as much detail aspossible.
N99
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 75/218
iMac (21.5-inch, Late 2009) Symptom Charts — Input/Output Devices 752009-11-24
Input/Output Devices
Apple Remote Inoperable
Unlikely cause: LCD display, power supply, hard drive, optical drive, fans
Quick Check
Symptoms Quick Check
Apple Remote InoperableApple Remote doesn’t bring up•Front RowApple Remote doesn’t control•iTunesApple Remote doesn’t control•computer volume
Make sure Apple Remote is within 30 ft. of1.computer, and has an unobstructed line-of-sightto computer.
Make sure lens end of Apple Remote is pointing2.directly at front of computer.
Make sure “Disable remote control infrared3.receiver” checkbox in System Preferences >Security is not checked.
Ensure that all software and rmware updates for4.this model have been installed to take advantageof any available bug xes.
Deep Dive
Check Result Action Code
Open Photo Booth or iChat’s1.
video preview window. PointApple Remote at built-incamera and press any buttonon Apple Remote. Verify if awhite, ashing light is visible invideo preview.
Yes Apple Remote is functioning.
Go to step 2.
No Replace Apple Remotebattery. Go to step 3.
Open System Preferences2.> Security. Verify if “Unpair”setting is available in thispreference panel.
Yes Click “Unpair” button todisable possible pairing withanother Apple Remote. Go to step 4.
No Possible IR board issue.
Go to step 5.With replacement battery,3.verify if white ashing lightis visible coming from AppleRemote in video previewwindow.
Yes Battery issue. Issue resolved. X05
No Apple Remote defective.Replace Apple Remote.
X04
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 76/218
iMac (21.5-inch, Late 2009) Symptom Charts — Input/Output Devices 762009-11-24
After clicking “Unpair”, verify if4.the computer now responds tothe Apple Remote.
Yes Pairing issue. Issue resolved.
No Possible IR board issue. Go to step 5.
Open System Proler. Verify if5.“IR Receiver” is listed in USB list
of devices.
Yes IR board reporting on USBbus. Check for lens block.
Go to step 6.
No Inspect and reseat IR cableconnection to logic board. Go to step 7.
Check that IR board is correctly6.tted and aligned with Applewindow and that lens is notblocked by any foreign materialand re-test. Verify if computerresponds to Apple Remote.
Yes Lens blocked or sensor notaligned with window. Issueresolved.
X03
No Lens damaged or inoperable.Replace IR board. Go to step 7.
After reseating or replacing7. IR board, verify if “IR Receiver”is listed under USB in SystemProler, and that computer nowresponds to Apple Remote.
Yes IR module reseated/replaced.Issue resolved. X03
No If IR board was only reseated,replace IR cable. Go to step 8.
After replacing IR cable, verify8.if “IR Receiver” is listed underUSB in System Proler, and thatcomputer now responds toApple Remote.
Yes IR cable replaced. Issueresolved.
X03
No Replace IR board. Go to step 9.
After replacing IR board, verify9.if “IR Receiver” is listed underUSB in System Proler, and thatcomputer now responds toApple Remote.
Yes IR board replaced. Issueresolved.
X03
No Replace logic board. M23
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 77/218
iMac (21.5-inch, Late 2009) Symptom Charts — Input/Output Devices 772009-11-24
Audio: Microphone
Unlikely cause: LCD display, power supply, hard drive, optical drive, fans
Quick Check
Symptoms Quick Check Audio: Microphone
Microphone not working•Microphone audio garbled•No sound•
Verify that no tape, sticky notes, or other objects1.are blocking microphone located on top ofcomputer near camera. Microscopic perforationson top of computer must be free of obstructionsin order for microphone to function.
Go to System Preferences > Sound > Input. 2.Verify that sound input device is set to internalmicrophone.
Go to System Preferences > Sound > Input. 3.Verify that “Input volume” setting is set above
minimum level.Go to System Preferences > Sound > Input. 4.Verify that “Input level” indicator moves whenspeaking into microphone.
Deep Dive
Check Result Action Code
Verify if boot chime is present1.when system is poweredON. Make sure audio outputpreferences are not set to mute.
Yes Go to step 2.
No Reset PRAM and retest.
Make sure no cables are2.connected to external soundinput/output ports. Go toSystem Preferences > Sound >Input and verify that “Internalmicrophone” is an availableoption.
Yes Go to step 3.
No Replace audio cable. M09
Go to System Preferences >3.Sound > Input and verify if“Input volume” is set above
minimum sensitivity.
Yes Go to step 4.
No Set “Input volume” slider to
middle position. Retest.
Go to System Preferences4.> Sound > Input and verifyif “Input level” indicatormoves when speaking intomicrophone.
Yes Microphone and audio inputfunctioning. Go to step 6.
No Suspect bad microphoneconnection. Reseatmicrophone connector onlogic board. Go to step 5.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 78/218
iMac (21.5-inch, Late 2009) Symptom Charts — Input/Output Devices 782009-11-24
Inspect microphone cable5.routing and verify if cable ispinched or damaged.
Yes Replace rear housing(microphone cable notavailable separately).
L14
No Go to step 6.
Record sound sample using6.
GarageBand or iMovie. Verify ifsound quality of sound sampleis normal during playback.
Yes Microphone circuitry OK.
Return system to user.
No Replace logic board. M09
Audio: Built-in Speakers Have Distorted Sound
Unlikely cause: LCD display, power supply, hard drive, optical drive, fans
Quick Check
Symptoms Quick Check
Audio: Built-in Speakers HaveDistorted Sound
No audio from one or both•speakers.Audio from speakers distorted•
Go to System Preferences > Sound > Output.1.Verify that sound output device is set to internalspeakers and that balance control is set to thecenter position.
Obtain known-good high-quality sound le or2.use iTunes Store sound samples to evaluatesound quality. Verify suspect sound les onanother system to determine if distortion iscaused by computer or sound le.
Set volume control to mid-range. Overdriving3. built-in speakers can cause distortion.
Deep Dive
Check Result Action Code
Go to System Preferences >1.Sound > Output. Set speakerbalance 100% to LEFT speakerand play a known-good soundle. Verify if sound is generatedby LEFT speaker and that soundquality is acceptable.
Yes LEFT speaker and ampliercircuitry OK. Go to step 2.
No Distortion detected in LEFTspeaker. Set Balance slider to
middle position. Go to step 3.
Set speaker balance 100%2.to RIGHT speaker and play aknown-good sound le. Verifyif sound is generated by RIGHTspeaker and that sound qualityis acceptable.
Yes RIGHT speaker and ampliercircuitry OK. Set Balance sliderto middle. Go to step 3.
No Distortion detected in RIGHTspeaker. Go to step 4.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 79/218
iMac (21.5-inch, Late 2009) Symptom Charts — Input/Output Devices 792009-11-24
Connect external speakers or3.headphones to audio-out portand play a known-good soundle. Verify if sound quality isacceptable.
Yes Suspect bad speaker. Go to step 4.
No Audio CODEC or amplierissue suspected. Replace logicboard and retest.
M09
Inspect LEFT and RIGHT4.speaker cones and speakerconnection cable for damage.Verify if speakers have visibledamage.
Yes Replace damaged speaker.Retest.
L11
No Go to step 5.
Install known-good speaker5.into location where distortedsound was heard. Verify ifsound quality improves.
Yes Replace speaker. L11
No Speaker amplier issuesuspected. Replace logicboard.
M09
Audio: Built-in Speakers Have No Audio
Unlikely cause: LCD display, power supply, hard drive, optical drive, fans
Quick Check
Symptoms Quick Check
Audio: Built-in Speakers Have NoAudio
No audio from one or both•speakers.Audio from speakers distorted•
Go to System Preferences > Sound > Output.1.Verify that sound output device is set to internal
speakers.Go to System Preferences > Sound > Output.2.Verify that “Output volume” setting is set abovethe minimum level and that “Mute” checkbox isnot selected.
Go to System Preferences > Sound > Output.3.Verify that “Balance” slider is set to middleposition so left and right speakers are both used.
Deep Dive
Check Result Action Code
Verify if boot chime is present1.when system is poweredON. Make sure audio outputpreferences are not set to muteand volume is set to mid-range.
Yes Go to step 2.
No Reset PRAM and retest.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 80/218
iMac (21.5-inch, Late 2009) Symptom Charts — Input/Output Devices 802009-11-24
Make sure no cables are2.connected to external soundinput/output ports. Go toSystem Preferences > Sound >Output and verify that “Internalspeakers” is an available option.
Yes Go to step 3.
No If “Headphones” is the onlyavailable sound outputdevice, replace audio cable.
If “Digital output” is the
only available sound outputdevice, reseat audio cable tologic board. If issue persists,replace audio cable.
If issue persists, replace logicboard.
L11
L11
M09
Go to System Preferences >3.Sound > Output. Set speakerbalance 100% to LEFT speakerand play a known-good soundle. Verify if sound is generated
by LEFT speaker and that soundquality is acceptable.
Yes LEFT speaker and ampliercircuitry OK. Go to step 4.
No No audio in LEFT speaker. Go to step 7.
Set speaker balance 100%4.to RIGHT speaker and play aknown-good sound le. Verifyif sound is generated by RIGHTspeaker and that sound qualityis acceptable.
Yes RIGHT speaker and ampliercircuitry OK. Set Balance sliderto middle. Go to step 5.
No No audio in RIGHT speaker. Go to step 7.
Verify if user-reported audio5.issue has been resolved.
Yes Issue no longer present.Return system to user.
No Go to step 6.
Boot system from Install6.DVD or another known-goodbootable volume. Verify if issuestill occurs.
Yes Go to step 7.
No Known-good boot volumeworks OK. Troubleshoot forsoftware issue. Isolate if issueis application-specic or apossible OS conict.
Connect external speakers or7.headphones to audio-out portand play a known-good soundle. Verify if sound quality isacceptable.
Yes Logic board, internalspeakers, and audio-out portfunctioning correctly. Returnsystem to user.
No Go to step 8.
Disconnect and carefully8.inspect audio cable andconnection to logic board fordamage such as bent pins orpinched/cut wires.
Yes Replace damaged audiocable. If issue persists, verify ifsymptom has changed.
L14
No Replace logic board. M09
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 81/218
iMac (21.5-inch, Late 2009) Symptom Charts — Input/Output Devices 812009-11-24
Camera Issues
Unlikely cause: LCD display, power supply, hard drive, optical drive, fans, speakers, microphone
Quick Check
Symptoms Quick Check Camera Issues
Camera not detected•No green LED for camera•Excessive blooming•Poor White Balance•Poor Focus•Green image•Image distortion•
Launch System Proler and conrm that system’s1.USB hub and built-in camera are visible.
Verify camera lens and glass panel are clean and2.free of contaminants. Clean glass panel if needed.
Launch Photo Booth to verify that green indicator3.LED near camera lens turns on and image qualityis acceptable.
Deep Dive
Check Result Action Code
Launch System Proler and1.verify built-in camera is visiblein USB list of devices.
Yes Camera recognized. Go to step 2
No Inspect and reseat cameracable connection on logicboard. Go to step 2.
Launch Photo Booth. Verify if2.green LED near camera lens
turns ON and image appearsnormal.
Yes Camera functioning. Returnsystem to user.
No Remove glass and clean bothsides. Clean camera lens.
If issue persists, replacecamera cable.
If issue persists, replacecamera.
If issue persists, replace logicboard.
X07
X07
M13
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 82/218
iMac (21.5-inch, Late 2009) Symptom Charts — Input/Output Devices 822009-11-24
FireWire Device Not Recognized
Unlikely cause: LCD display, power supply, hard drive, optical drive, fans
Quick Check
Symptoms Quick Check FireWire Device Not Recognized
FireWire hard drive not•recognizedFireWire optical drive not•recognizedFireWire camera not recognized•FireWire printer not recognized•
For external FireWire drives, make sure any1.external power source is plugged in andoperating to isolate a power issue with thedevice.
Test a known-good FireWire device to isolate a2.failed peripheral issue.
Test a known-good FireWire cable to isolate a3.FireWire cable issue.
Ensure that all software and rmware updates for4.this model have been installed to take advantageof any available bug xes.
Launch System Proler and verify if the aected5.FireWire device is visible on FireWire bus. If yes,then FireWire port and cable are functioningproperly. Contact FireWire device manufacturer toverify that device is supported.
Deep Dive
Check Result Action Code
Unplug all FireWire devices1. from computer. Reset PRAM.Reconnect FireWire devicein question. Verify if FireWiredevice is recognized.
Yes Issue resolved.
No Possible logic board failure. Go to step 2.
Use a known-good FireWire2.cable with a known-goodFireWire device (such asanother Mac in Target DiskMode). Verify if FireWire deviceis recognized.
Yes Try FireWire device in questionwith a known-good computerof same model. Go to step 3.
No FireWire not recognized.Replace logic board.
M12
Verify if FireWire device is3.recognized on a known-goodsame model computer.
Yes Go to step 4.
No Device may need additionalpower. Use a powered FireWirehub. Go to step 5.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 83/218
iMac (21.5-inch, Late 2009) Symptom Charts — Input/Output Devices 832009-11-24
Verify if FireWire device is4.recognized with a known-good FireWire cable on user’scomputer.
Yes FireWire cable issue. Issueresolved.
No FireWire device may needadditional power. Go to step 5.
Using a powered FireWire5.
hub, and having installed anysoftware or rmware updatesfor the device, verify if FireWiredevice is now recognized.
Yes Device recognized. Required
additional power from hub orupdate. Issue resolved.
No Device may require additionalsoftware, or there may be aconict in the Mac OS. Go tostep 6.
Create a new user in System6.Preferences > Accounts andlog out current user. Log inon new user account andverify if FireWire device is now
recognized.
Yes Software Issue. Troubleshootsoftware on User account. Issueresolved.
No Apply all Mac OS and FireWire
specic updates. If issuepersists, contact devicemanufacturer for support.FireWire port and cable havebeen veried.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 84/218
iMac (21.5-inch, Late 2009) Symptom Charts — Input/Output Devices 842009-11-24
USB Device Not Recognized
Unlikely cause: LCD display, power supply, hard drive, optical drive, fans
Quick Check
Symptoms Quick Check USB Device Not Recognized
USB wired keyboard/mouse not•recognizedUSB external drive not•recognizedUSB camera not recognized•USB printer not recognized•
Reset SMC.1.
For printers and external USB drives, make sure2.any external power source is plugged in andoperating to isolate a power issue with device.
The iMac has 4 USB ports on rear of computer. Try3.each port to isolate a particular port malfunction.
Test with a known-good wired keyboard or4.mouse to isolate a failed peripheral issue.
Test with a known-good USB cable when dealing5.
with a printer or external USB drive, to isolate aUSB cable issue.
Ensure that all software and rmware updates for6.this model have been installed to take advantageof any available bug xes.
Launch System Proler and verify if device is7.visible on USB bus. If yes, then the USB port andcable are functioning properly. Contact devicemanufacturer to verify that device is supported.
Deep Dive
Check Result Action Code
Unplug all USB devices from1.the computer except for USBkeyboard and mouse. Startcomputer and reset PRAM.Verify if USB keyboard andmouse are recognized.
Yes Test with all USB ports toensure all USB ports workingas expected. Replace logicboard for any port failures.
No Reset SMC. Go to step 2.
Verify if Bluetooth Mouse Setup2.assistant launches after startup.
Yes Bluetooth detected, butexternal USB devices notrecognized. Go to step 3.
No Disconnect USB keyboard andmouse. Go to step 4.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 85/218
iMac (21.5-inch, Late 2009) Symptom Charts — Input/Output Devices 852009-11-24
Verify if a known-good USB3.keyboard and mouse arerecognized.
Yes Test original USB mouse andkeyboard. Replace if still notrecognized. Go to step 5.
No External USB ports notfunctioning. Replace logicboard.
M15
With no USB devices4.connected, restart computer.Verify if Bluetooth Mouse Setupassistant launches after startup.
Yes Bluetooth detected. Go to step 3.
No Bluetooth not recognized.Internal and external USB notfunctioning. Replace logicboard.
M15
With known-good USB5.keyboard and mouse working,test USB peripheral in question(USB hard drive or printer, etc.)
Verify if device is recognized inSystem Proler under USB.
Yes Device recognized. Test in allUSB ports to ensure all USBports working as expected.Replace logic board for any
port failures.
M15
No Device may require morepower than supplied by USBports. Test with a poweredUSB hub. Go to step 6.
Verify if using a powered USB6.hub resolves the issue.
Yes Test device on same USB portof a same-model computer.If other computer does notrequire a powered USB hubto allow functionality, replacelogic board.
M15
No Ensure all software andrmware updates havebeen applied for computerand device. If issue persists,contact device manufacturerfor support. The computer’sUSB ports and cable havebeen veried.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 86/218
iMac (21.5-inch, Late 2009) Symptom Charts — Input/Output Devices 862009-11-24
Wired Keyboard Does Not Function Properly
Unlikely cause: LCD display, power supply, hard drive, optical drive, fans
Quick Check
Symptoms Quick Check Wired Keyboard Does NotFunction Properly
Some or all keys on the•keyboard don’t work Eject key or Caps Lock key•doesn’t seem to work Some keys don’t work as•expected
Reset SMC1.
Open System Preferences > Universal Access >2.Mouse & Trackpad and verify that Mouse Keysis turned OFF. When enabled, Mouse Keys candisable functionality of some or most keys,depending on keyboard used.
The iMac has 4 USB ports on rear of computer.3.Make sure to try each port to isolate a particularport malfunction.
Test with a known-good wired keyboard to4.isolate a failed peripheral issue.
Test wired keyboard on a known-good, same-5.model computer. If it works on the othercomputer, this may indicate a bad USB port ifkeyboard doesn’t work at all on user ’s computer,or a software issue if keyboard is working but notas expected on user’s computer.
Ensure that all software and rmware updates for6.this model have been installed to take advantageof any available bug xes.
Deep Dive
Check Result Action Code
Verify if all keys on keyboard1.work.
Yes Go to step 2.
No Go to USB Device NotRecognized symptom ow.
Verify if Caps Lock is working as2.expected.
Yes Go to step 3.
No Go to Keyboard: SpecicKeys Do Not Respond
symptom owVerify if media Eject key is3.working as expected. Note thatto prevent accidentally ejectingmedia, Mac OS X adds a slightdelay to the media Eject keybefore it takes eect.
Yes Go to step 4.
No Go to step 5.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 87/218
iMac (21.5-inch, Late 2009) Symptom Charts — Input/Output Devices 872009-11-24
Open System Preferences >4.Speech. Verify if the “Speakselected text when the key ispressed” checkbox is selected.
Yes The key combination to speaktext cannot be used for anyother purpose. Either disable,or change to a more rarekey combination (includingShift, Command, Option and
Control).No Go to step 6. M15
With optical media in the drive,5.hold the media Eject key. Verifyif the eject symbol appears onscreen and that optical mediais ejected if present.
Yes Normal media eject key delay.No repair necessary.
No Go to Optical Drive Won’tAccept/Eject Media
symptom ow.
Open System Preferences >6.Language and Text > InputMenu. Check “Keyboard Viewer”.
From the Input Menu (ag) inthe Menu Bar, choose “ShowKeyboard Viewer”. Verify if keyspressed appear in KeyboardViewer.
Yes Keys recognized. Go to step 9.
No Keys not recognized. Replace keyboard.
K01
Open TextEdit or another text7.application and try typingsomething using the non-responding keys. Verify ifthey are typed in this otherapplication.
Yes Application-specic issue. Troubleshoot application.
No Create a new user accountin System Preferences >Accounts, log out fromcurrent user and log in with
new user to isolate a Useraccount related issue. If issuepersists, reinstall Mac OS Xfrom Install DVD.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 88/218
iMac (21.5-inch, Late 2009) Symptom Charts — Input/Output Devices 882009-11-24
Keyboard: Specic Keys Do Not Respond
Unlikely cause: LCD display, power supply, hard drive, optical drive, fans
Quick Check
Symptoms Quick Check Keyboard: Specic Keys Do NotRespond
One or more keys do not•respond when pressedKey sticks•Keycap missing•
If wireless keyboard is being used verify that it is1.properly paired with computer. Go to WirelessInput Device Doesn’t Pair symptom ow toresolve pairing issues.
The caps lock key has a built-in delay to reduce2.accidental activation and must be held forapproximately ½ second for it to be activated. SeekBase #TS1578: Apple Keyboard (2007): CapsLock modied to reduce accidental activation.
Inspect keyboard for signs of liquid spills or other3.
contamination. Apple’s warranty does not coveraccidental damage.
If keycap is loose attempt to reattach it.4.
For other keyboard issues jump to appropriate5.symptom ow.
Wired Keyboard/Mouse Not Recognized
Unlikely cause: LCD display, power supply, hard drive, optical drive, fans
Quick Check
Symptoms Quick Check
Wired Keyboard/Mouse NotRecognized
USB wired keyboard/mouse not•recognized when plugged in.Mouse scroll ball not working•or not working as expected.Mouse buttons not working or•not working as expected.
Reset SMC.1.
The iMac has 4 USB ports on rear of computer.2.Make sure to try each port to isolate a particularport malfunction.
Test with a known-good wired keyboard or3.mouse to isolate a failed peripheral issue.
Test a mouse when connected directly to ports4.on the back of iMac to isolate a keyboard USBport issue.
Ensure that all software and rmware updates for5.this model have been installed to take advantageof any available bug xes.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 89/218
iMac (21.5-inch, Late 2009) Symptom Charts — Input/Output Devices 892009-11-24
Deep Dive
Check Result Action Code
Verify if computer recognizes1.keyboard or mouse whenplugged into rear USB ports onback of iMac.
Yes Test device in all USB ports toensure all other USB ports areworking as expected.
Replace logic board if anyUSB port on rear fails.
Replace keyboard if any USBport on keyboard fails.
Go to step 2.
M15
K11
No Go to USB Device NotRecognized symptom ow.
Verify if keyboard is working as2.expected.
Yes Go to step 3.
No Go to Wired Keyboard Does
Not Function Properly symptom ow.
Verify if mouse has an issue3.with scroll ball.
Yes See kBase #HT1537: How toclean your Mighty Mouse.
No Go to step 4.
Verify if mouse has an issue4.with buttons.
Yes Go to step 7.
No Go to step 5.
Verify if mouse has an issue5.with tracking.
Yes Go to step 6.
No Go to step 7. Try using mouse on another6.surface. Non-reective, opaquesurfaces without repetitivepatterns work best. The surfaceshould be clean but not shiny.Verify if mouse tracks correctlywhen used on another surface.
Yes Surface issue. Issue resolved.
No Go to step 7
See7. kBase #HT1581:Troubleshooting MightyMouse and determiningexpected behavior. Verify ifthis article resolves issue.
Yes Issue resolved.
No Replace wired mouse. K99
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 90/218
iMac (21.5-inch, Late 2009) Symptom Charts — Input/Output Devices 902009-11-24
Uncategorized Symptoms
Quick Check
Symptoms Quick Check
Uncategorized SymptomsUnable to locate appropriate•symptom code.
Reset SMC.1.Verify that external I/O device (where applicable)2.works on a known-good, same-model computer.
For third party I/O devices, make sure necessary3.software is installed and up-to-date, and thatdevice is supported with user’s system.
Deep Dive
Check Result Action Code
Verify if existing symptom code1. applies to issue reported byuser.
Yes Jump to appropriatesymptom code ow.
No Document reported failureand send feedback [email protected]
stating that a suitablesymptom code wasn’t found.Provide as much detail aspossible.
N99
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 91/218
iMac (21.5-inch, Late 2009) Symptom Charts — Mechanical 912009-11-24
Mechanical
Noise/Hum/Vibration
Unlikely cause: LCD panel, glass panel, enclosure, cables
Quick Check
Symptoms Quick Check
Noise/Hum/VibrationBuzzing noise•Rattling noise•
Ticking noise•Squeaking noise•
Verify that the vents on the bottom and1.back of the system are free of dust and otherobstructions that might inhibit proper airowthrough the system.
Launch Applications/Utilities/Activity Monitor.2.Determine whether an application or process is
consuming a high percentage of CPU bandwidth.CPU-intensive applications can cause the fansto run fast in order to maintain the properinternal system temperatures. If needed, quit theapplication or restart the system to resolve theissue.
Eject optical media from optical drive. Out-of-3.balance optical media can generate audiblenoise. To resolve try a dierent brand of media.For additional information, go to Optical DriveNoisy symptom ow.
Tilt display to hinge limits to determine if4.
mechanical noise is generated by the hingemechanism. For additional information, go toStand/Hinge Issues symptom ow.
Play sound sample at loud and soft volume5.levels to determine if the noise is caused by theleft/right speakers or the amplier circuit. Plugexternal headphones to identify whether thenoise comes from audio out or from other source.For additional information, go to Audio: Built-inSpeakers Have Distorted Sound symptom ow.
Adjust the display brightness to determine6.whether the noise is related to the brightnesslevel. For additional information, go to Noise/Unstable Flickering symptom ow.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 92/218
iMac (21.5-inch, Late 2009) Symptom Charts — Mechanical 922009-11-24
Deep Dive
Check Result Action Code
Verify if any tape, gasket, cable1.label, or cable is touchingthe fan blades and causing a
ticking noise.
Yes Secure the material so itdoesn’t touch fan blades. Iftape adhesive has lost its
stickiness, replace that sectionof tape.
No Go to step 2.
Run Apple System Diagnostic.2.Verify if running ASD generatesone or more errors.
Yes Go to ASD Error Codestable to decode error. Followinstructions in table forresolving error, then retest.
No Go to step 3.
Verify if noise sounds like one3.or more fans are spinning faster
than expected.
Yes Reset SMC by disconnectingpower cord for ~15 seconds
then retest. If issue continuesgo to step 3.
No Go to step 6.
Verify if noise changes when4.optical drive is being accessedor media is inserted or ejected.
Yes Suspect issue with opticaldrive or media used.Go to Optical Drive Noisy
symptom ow.
No Go to step 5.
Mute the system volume. Verify5.if issue still occurs.
Yes Go to step 6.
No Suspect issue with speakersor audio amplier circuitry.Go to Audio: Built-inSpeakers Have DistortedSound symptom ow.
Adjust brightness on display6.between maximum andminimum settings. Verify ifissue changes depending onbrightness level.
Yes Suspect issue with LCDdisplay or backlight controllerboard. Go to Noise/UnstableFlickering symptom ow.
No Go to step 7.
Remove fans and rotate7.
blades. Verify if fan blades spinsmoothly without interferencefrom fan housing.
Yes Go to step 8.
No Replace aected fan. P04
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 93/218
iMac (21.5-inch, Late 2009) Symptom Charts — Mechanical 932009-11-24
Reinstall fans while carefully8.ensuring that there are nocables routed under or nearfan assembly that might causeinterference with fan blades.After reassembling system
verify if noise issue is resolved.
Yes Noise issue resolved. Suspectissue caused by interferencefrom wiring or possibledistortion or fan housingwhen installed in system.
P04
No Go to step 9. Temporarily remove LCD9.display then power ON system.Verify if source of noise can belocated. Caution: The exposedpower supply poses a seriousshock hazard. Take properprecautions when workingaround an energized system.
Yes Identify, inspect, and ifnecessary replace part thatcaused noise issue.
P04
No Go to step 10.
Disconnect these major10.modules/parts (hard drive,optical drive, fans, LCD display)one at a time then power ONthe system. Determine if noiseissue goes away when one ofthe modules is disconnected. Caution: The exposed powersupply poses a serious shockhazard. Take proper precautionswhen working around anenergized system.
Yes Identify, inspect, and ifnecessary replace part thatcaused noise to disappearwhen it was disconnectedfrom the system.
P04
No All parts veried. Verify thatcorrect symptom ow isbeing used.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 94/218
iMac (21.5-inch, Late 2009) Symptom Charts — Mechanical 942009-11-24
Fan Failures / Thermal Issues
Unlikely cause: speakers
Quick Check
Symptoms Quick Check Fan Failures / Thermal Issues
System feels very hot•Fan(s) not operating•Fan(s) running fast•System is noisy•
Verify that vents on bottom and back of system1.are free of dust and other obstructions that mightinhibit proper airow through the system.
Verify that computer is not exposed to direct2.sunlight which may heat up enclosure, making itfeel hot to the touch.
Verify computer is not running hotter than3.expected for normal operation. If possible,compare to a similarly congured system. Note:Power supply is located in upper left corner
where highest temperatures can usually be felt.Launch Applications/Utilities/Activity Monitor.4.Verify if an application or process is consuminga high percentage of CPU bandwidth. CPU-intensive applications can cause fans to runfast in order to maintain proper internal systemtemperatures. If needed, quit the application orrestart the system to resolve issue.
Reset SMC by unplugging power cord for ~155.seconds.
Deep DiveCheck Result Action Code
Run Apple System Diagnostic.1.Verify if ASD generates one ormore errors.
Yes Suspect possible fan or sensorerror. Go to ASD Error Codestable to decode error. Followinstructions in table forresolving error, then retest.
No Go to step 2.
Verify if noise sounds like one2.
or more fans running fasterthan expected.
Yes Fans running fast. Reset SMC
by disconnecting power cordfor ~15 seconds then retest. Ifissue continues go to step 3.
No Go to step 3.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 95/218
iMac (21.5-inch, Late 2009) Symptom Charts — Mechanical 952009-11-24
Verify if any tape, gasket, cable3.label, or cable is touchingthe fan blades and causing aticking noise.
Yes Secure the material so itdoesn’t touch fan blades. Iftape adhesive has lost itsstickiness, replace that sectionof tape.
No Go to step 4.
Remove fans and rotate blades.4.Check for any dust that couldbe clogging the fans. Verifyif fan blades spin smoothlywithout interference from fanhousing and fan blades are allintact.
Yes Go to step 5.
No Replace aected fan(s). P06
Run Apple Service Diagnostics5.stand-alone tests in loopingmode, and verify if all sensor orfans related tests pass.
Yes Noise issue resolved.
No Check for correct sensors/fansconnections on logic board.
Check for pinched cables.Compare with known-goodsimilar system, and checkfor unlisted sensors. Replaceaected sensor/fan.
P06
Stand/Hinge Issues
Symptoms Quick Check
Stand/Hinge IssuesBent stand•Broken hinge•Stripped screw/head•Stripped screw boss•
Determine if damage caused by user /technician1.environment, accidental damage, or abuse. Ifso, inform user/technician the failures are notcovered by Apple warranties. Refer tohttp://www.apple.com/legal/warranty
For hinge noise issues replace hinge mechanism.2.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 96/218
iMac (21.5-inch, Late 2009) Symptom Charts — Mechanical 962009-11-24
Physical Damage
Symptoms Quick Check
Physical DamageBroken glass•Bent stand•Broken hinge•Stripped screw/head•Stripped screw boss•Dent or scratch to chassis•
Verify if damage caused by user environment,1.accidental damage, or abuse. If applicable informthe user that Apple does not warrant damagecaused by accident, abuse, misuse, ood, re,earthquake, or other external causes. Refer to:http://www.apple.com/legal/warranty
Uncategorized Symptoms
Check Result Action Code
Verify if existing symptom code1.applies to issue reported byuser.
Yes Jump to appropriatesymptom code ow.
No Document reported failureand send feedback [email protected]
stating that a suitablesymptom code wasn’t found.Provide as much detail aspossible.
N99
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 97/218
© 2009 Apple Inc. All rights reserved.
Apple Technician Guide
Take ApartiMac (21.5-inch, Late 2009)
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 98/218
iMac (21.5-inch, Late 2009) Take Apart — General Information 982009-11-24
General Information
Opening the Unit
The• iMac (21.5-inch, Late 2009) has a glass panel that attaches to the front, which must beremoved prior to replacing any module on the unit.Important:• The glass panel should only be removed by Apple-authorized technicians.Follow all cleaning and handling instructions to prevent damaging glass panel or LCD panel.Follow ESD precautions when glass panel is removed.•
For more information about ESD, refer to: kBase #HT3451: Electrostatic Discharge Precautions and Myths AppleCare Service Training: ESD Precautions
Required Tools
The following tools are required to service an iMac (21.5-inch, Late 2009):ESD-safe workstation, including an ESD mat and wrist or heel strap•ESD bags (for storing ESD-sensitive parts while removed from unit)•Magnetized Torx T10 screwdriver•Magnetized Torx T8 screwdriver•Magnetized Torx T6 screwdriver•Phillips #2 screwdriver•Black stick (nylon probe, Apple part #922-5065) or other non-conductive nylon or plastic•
at-blade tool Thermal paste (thermal compound syringe, Apple part #922-7144)•Kapton tape•Magnifying glass, for reading serial number etched on bottom of stand•Digital volt meter (for troubleshooting)•Soft, clean towel or cloth (to protect display and removed parts from scratches)•
For more information about tools, refer to: kBase #HT3452: Hand Tools for Desktop and Portable Repairs
In addition, the following software programs are required for troubleshooting:Apple Service Diagnostic (ASD), version 3S133 or later•Apple Hardware Test (AHT), version 3A176 or later•Bluetooth Service Diagnostic•
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 99/218
iMac (21.5-inch, Late 2009) Take Apart — General Information 992009-11-24
Required Special Tools for Glass Panel
Special tools are required to remove, handle and clean glass panel.922-8252 – Suction cups, Pkg of 2•922-8253 – Gloves, lint-free, anti-static, Pkg of 2•922-8258 – ESD bags, 24”x20”, Pkg of 5. To prevent buildup of static charges which may•
attract dust particles, store LCD panel in an ESD bag when it is removed from unit.922-8259 – Microfoam bag to store glass panel, Pkg of 5•922-8261 – Sticky silicone roller (6-inch) to clean glass panel•922-8262 – Sticky sheet pads to clean silicone roller•922-8263 – Polishing cloths, anti-static, optical-grade micro-terry, Pkg of 5•iKlear Apple Polish or Brillianize anti-static spray cleaning solution. If you are unable to•source iKlear or Brillianize, IPA (isopropyl alcohol) can be used to clean glass.
Cleaning Tools Starter Kit
The following tools are oered in the cleaning starter kit (076-1277):Suction cups, 1 pair•Gloves, lint-free, anti-static, 2 pairs•Sticky silicone roller (6-inch) to clean glass panel•Sticky sheets to clean the silicone roller, 2 pads•Polishing cloths, clean, anti-static, optical-grade micro-ber “terry” style, 5 cloths•Microfoam bag to store glass panel, 5 bags•ESD bag for LCD panel storage, 5 bags•
Cleaning Tool Resources
Note: Apple Retail technicians should refer to standard internal resources for tool ordering.MCM Portal •http://www.mcmb2b.com/appleasp
LENSPEN: LapTop Pro or VidiMax are very eective in removing ngerprints on LCD and•inside surface of glass. http://www.lenspen.com/
iKlear Apple Polish •http://www.klearscreen.com/iKlear.aspxl
Brillianize •
http://www.brillianize.com/
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 100/218
iMac (21.5-inch, Late 2009) Take Apart — General Information 1002009-11-24
Cleaning & Handling the Glass Panel
Follow cleaning procedures in this manual to ensure glass panel is free of dust and otherparticles before returning the computer to customer.
The glass panel is not tempered and will break into sharp pieces of mishandled.•A scratched or broken glass panel is not covered under warranty.Removing glass panel requires special tools such as lint-free gloves, rubber suction cups,•microfoam storage bags, and iKlear cleaning solution.
To prevent contamination, wear lint-free gloves and handle glass only by edges.•
Do’s and Don’ts
DOHandle glass panel using lint-free gloves.•Use only a sticky silicone roller to clean the inside surface of glass and LCD panel.•Use iKlear ONLY on the outside surface of glass panel.•Place glass panel into a clean protective microfoam bag when removed from unit.•Store glass panel in a safe area where it will not be broken or damaged.•Store LCD panel in an anti-static bag to prevent buildup of static charges which may attract•dust particles to display’s surface.Store silicone roller and sticky paper within a temperature range of 39-104 F (5-40 C).•If silicone roller is no longer tacky, wash it in warm soapy water or wipe with isopropyl•alcohol. If tackiness does not return, replace silicone roller.
DON’T Touch inside of glass with bare hands or dirty gloves. Fingerprints are dicult to remove.•Place glass panel onto a work surface where it may collect dust and other contaminants•unless it has rst been placed into a protective microfoam bag.
Handling a Broken Glass Panel
The glass panel is not tempered and will break into sharp pieces if mishandled. If the glass isbroken it must be carefully removed from the unit to prevent irreparable damage to the frontsurface of the LCD. If the front surface of the LCD is scratched by broken glass, the LCD mayneed to be replaced.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 101/218
iMac (21.5-inch, Late 2009) Take Apart — General Information 1012009-11-24
How to Remove a Broken Glass Panel
A shattered panel can be removed using safety glasses, packing tape, and leather gloves.
Put on the safety glasses and leather gloves.1.
Lay the computer on a smooth, clean work surface.2.
Peel protective covering o the front of the glass. Remove and discard any large pieces of3.broken glass.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 102/218
iMac (21.5-inch, Late 2009) Take Apart — General Information 1022009-11-24
Apply a strip of packing tape horizontally across the top and bottom of the glass panel.4.Next, apply the tape diagonally, across the broken glass panel, forming an “X.”
Continue applying tape horizontally, thoroughly covering the broken glass. Most of the5.glass will still be attached to the steel ring that runs around the perimeter of the glasspanel.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 103/218
iMac (21.5-inch, Late 2009) Take Apart — General Information 1032009-11-24
Use a black stick to pry the glass panel o the magnets on the rear housing.6.
Lift the entire glass panel o the rear housing.7.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 104/218
iMac (21.5-inch, Late 2009) Take Apart — General Information 1042009-11-24
Place the broken glass inside a large box, label the box, and dispose of it properly.8.
Using a whisk broom, clean the work surface of tiny glass particles.9.
Stand the iMac up and use a lint free cloth to carefully brush any of the particles o the10.iMac onto the table. Clean the work surface again.
When the repair is nished the cloth should be disposed of immediately.11.
Use a broom and dustpan to sweep up as much of the broken glass as possible. Glass12.fragments may have traveled several feet from the location of the glass panel, so be sure tothoroughly clean the entire area. Use a vacuum to remove the smaller fragments not pickedup by the broom.
Note: A broken glass panel may leave one or more scratches on the LCD display depending onthe severity of the glass breakage. As long as the LCD itself has not been fractured the LCD doesnot require replacement, but be sure to let the customer know that the scratches are there andwere caused by the broken glass panel.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 105/218
iMac (21.5-inch, Late 2009) Take Apart — General Information 1052009-11-24
Safety
Warning: HIGH VOLTAGE:The AC/DC power supply PCB remains powered up wheneversystem is plugged in, whether or not system has been turned on. Use extreme cautionwhen troubleshooting system with glass panel and LCD panel removed.
Don’t work alone. In the event of electrical shock it is important to have another•individual present who can provide assistance.Keep one hand in your pocket when working on any iMac system that is plugged•in. This will help ensure that your body does not provide a path to ground in theevent that you accidentally make contact with line voltage.Don’t wear jewelry, watches, necklaces, or other metallic articles that could present•a risk if they accidentally make contact with power supply circuitry.
Use extreme caution when working around power supply. The power supply contains ahigh voltage capacitor that may remain charged for several minutes even when computer isunplugged. Never touch leads on top side of power supply, especially capacitor leads locatednear warning sign.
Important: If computer is shut down by removing power cord, allow power supply a good 2-3minutes to discharge capacitors before handling it. However, if you select “Shut Down” via theApple menu, the computer will discharge power supply capacitor almost immediately.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 106/218
iMac (21.5-inch, Late 2009) Take Apart — General Information 1062009-11-24
Logic Board Handling
IMPORTANT: Always use two hands to support logic board and heatsink. Handling boardincorrectly could ex board and damage chips and circuitry. Never handle board by heatsink.
Reassembly StepsWhen no replacement steps are listed, replace parts in exact reverse order of Removalprocedure.
Note About Images in This Guide
Because a pre-production model was used for most images in this manual, you may notice smalldierences in appearance between the image pictured and the computer you are servicing.However, although appearance may dier, steps and sequence are the same unless noted.
Screw SizesAll screw sizes shown are approximate and represent the total length of the screw.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 107/218
iMac (21.5-inch, Late 2009) Take Apart — Access Door 1072009-11-24
First Steps
Shut down computer.•Wait 10 minutes.•Unplug all cables and•the power cord.Put on ESD strap.•Place computer face•down on a clean, atsurface so the bottomis facing you.
Tools
ESD wrist strap•Phillips #2 screwdriver•
Access Door
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 108/218
iMac (21.5-inch, Late 2009) Take Apart — Access Door 1082009-11-24
Removal
Raise the stand and1loosen 3 captivePhillips #2 screws.
Remove access door.2
Important: To ensureproper cooling, iMacshould not be operatedwithout access doorinstalled.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 109/218
iMac (21.5-inch, Late 2009) Take Apart — Memory 1092009-11-24
First Steps
Remove:Access Door•
Note: This computeruses PC3-8500, DDR3,1066 MHz SO-DIMMs.
The maximum amountof memory is 16GB, witha 4GB DIMM installed ineach slot.
Tools
ESD wrist strap•Black stick •
Memory
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 110/218
iMac (21.5-inch, Late 2009) Take Apart — Memory 1102009-11-24
Removal
Untuck tabs1in memorycompartment.
Pull tab to eject2installed memorymodule.
Reassembly
Orient notch on1memory withnotch in memorycompartment.
Press memory rmly2 into slot until youhear a click.
Tuck black plastic3tabs into memorycompartment.
Replace access door4and tighten 3 captive
screws.Important: To ensureproper cooling, iMacshould not be operatedwithout access doorinstalled.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 111/218
iMac (21.5-inch, Late 2009) Take Apart — Glass Panel 1112009-11-24
First Steps
Shut down computer.•Wait 10 minutes.•Unplug all cables and•the power cord.Put on ESD strap.•
Caution: The glass panel
is not tempered and willbreak into sharp pieces ifmishandled. A scratchedor broken glass panel isnot covered by warranty.
Important: This procedure requiresspecial tools, which areoered individually or aspart of a cleaning kit. See
General Take Apart sectionfor more information.
Tools
ESD wrist strap•lint-free gloves•
suction cups•sticky silicone roller•sticky sheets to clean•the silicone rollermicrofoam bag •to store glass panel
Glass Panel
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 112/218
iMac (21.5-inch, Late 2009) Take Apart — Glass Panel 1122009-11-24
Removal
Note: Glass panel is heldin place by magnets.
Caution: Unlike previousmodel iMacs, the glasspanel has tabs alongbottom that align withrear housing. Be carefulnot to damage tabs whenremoving glass panel.
Apple stronglyrecommends wearing
clean, lint-free gloveswhenever handling theglass panel, to reducecleaning required onreassembly.
Lay computer on1its back and pressclean suction cups inopposite corners onglass panel.
Lift panel up and o.2
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 113/218
iMac (21.5-inch, Late 2009) Take Apart — Glass Panel 1132009-11-24
Remove suction cups3and slide glass into
protective microfoambag.
Reassembly
Remove protective1covering from silicone
roller and sticky sheet.
Clean silicone roller2by rolling it back andforth a few times onsticky sheet.
If sticky sheet looksdirty, use a new one. If roller is no longer
tacky, wash it in warmsoapy water.If tackiness does notreturn, replace siliconeroller.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 114/218
iMac (21.5-inch, Late 2009) Take Apart — Glass Panel 1142009-11-24
Set unit in upright3position to minimize
settling of dust.
Roll silicone roller over4LCD panel to removeany particles.
Remove glass panel5from microfoam bag.
Clean INSIDE of glass6panel with the siliconeroller to remove dust.
Note: If ngerprintsor oils are on inside of
glass, clean rst withisopropyl alcohol.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 115/218
iMac (21.5-inch, Late 2009) Take Apart — Glass Panel 1152009-11-24
Wearing clean gloves,7place glass directly
onto unit, aligningtabs along bottomwith notches in rearhousing. Magnets willcatch it and hold it inplace.
Make sure glass is ushwith rear housing afterit is reinstalled.
Clean outside of glass8 panel with a cleanmicrober cloth. Ifnecessary, use a smallamount of iKlearpolish. Wipe glassuntil there is no longerany residue or haze.
Inspect glass for9any remaining dust,ngerprints, or a hazyresidue. If there arecontaminants trappedbetween LCD paneland glass panel, repeatcleaning procedure.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 116/218
iMac (21.5-inch, Late 2009) Take Apart — Camera 1162009-11-24
First Steps
Remove:Glass Panel•
Tools
ESD wrist strap• Torx T10 screwdriver•
Camera
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 117/218
iMac (21.5-inch, Late 2009) Take Apart — Camera 1172009-11-24
Removal
Remove T10 screws: 1(2) 922-xxxx
2 Lift camera bracket outof rear housing.
Disconnect camera3cable from cameraassembly.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 118/218
iMac (21.5-inch, Late 2009) Take Apart — LCD Panel 1182009-11-24
First Steps
Remove:Glass Panel•
Important: To preventbuildup of static charges
which may attract dustparticles to the surfaceof the display, store LCDpanel in an anti-staticbag whenever it has beenremoved from computer.
Tools
ESD wrist strap• Torx T10 screwdriver•ESD bag to store LCD•panel
LCD Panel
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 119/218
iMac (21.5-inch, Late 2009) Take Apart — LCD Panel 1192009-11-24
Removal
Remove T10 screws: 1(8) 922-9246
With computer2standing up and facingyou, pull the LCDforward slightly fromthe top edge.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 120/218
iMac (21.5-inch, Late 2009) Take Apart — LCD Panel 1202009-11-24
Looking down into3computer, disconnect 4cables:
#1: vertical sync•#2: backlight power•#3: display temp sensor•#4: LVDS•
LEFT: Close-up of #1vertical sync cable (922-9142) at top of LEDbacklight board. Pullstraight out of connector.
RIGHT: Close-up of #3display temp sensor cable(922-9141) at top center oflogic board.
LEFT: Close-up of #2backlight power cable atbottom of LED backlightboard. Pinch and pull cablefrom connector.
RIGHT: Close-up of #4LVDS cable (922-9132) at
top center of logic board.Squeeze both sides andpull to release cable fromconnector.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 121/218
iMac (21.5-inch, Late 2009) Take Apart — LCD Panel 1212009-11-24
Replacement Note:If installing a new LCD
panel, disconnect LVDScable and vertical synccable and transfer to newpanel. Secure with blackmylar tape included withnew LCD panel.
A replacement LCD panelincludes:
display temp sensor•cable & retaining clip
backlight power cable• mylar tape•
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 122/218
iMac (21.5-inch, Late 2009) Take Apart — Vertical Sync Cable 1222009-11-24
First Steps
Remove:Glass Panel•LCD Panel•
Removal
Peel back any black1mylar securing cableto LCD panel.
Pull cable straight out2of connector.
Vertical Sync Cable
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 123/218
iMac (21.5-inch, Late 2009) Take Apart — LCD Temp Sensor Cable 1232009-11-24
First Steps
Remove:Glass Panel•LCD Panel•
Removal
Peel back black1insulator to accessentire cable.
Disconnect cable2from bracket.
LCD Temp Sensor Cable
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 124/218
iMac (21.5-inch, Late 2009) Take Apart — LVDS Cable 1242009-11-24
First Steps
Remove:Glass Panel•LCD Panel•
Removal
Peel back any black1mylar securing cableto LCD panel.
Disconnect LVDS2cable by (2) pressingin on side release
clips and then (3)gently pulling down.
LVDS Cable
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 125/218
iMac (21.5-inch, Late 2009) Take Apart — Bluetooth Antenna 1252009-11-24
First Steps
Remove:Glass Panel•LCD Panel•
Tools
ESD wrist strap• Torx T8 screwdriver•
Bluetooth Antenna
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 126/218
iMac (21.5-inch, Late 2009) Take Apart — Bluetooth Antenna 1262009-11-24
Removal
Remove T8 screws: 1(2) 922-4723
Disconnect blue2antenna cable fromBluetooth board.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 127/218
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 128/218
iMac (21.5-inch, Late 2009) Take Apart — Bluetooth Board 1282009-11-24
Removal
Remove T8 screw: 1(1) 922-9247
Disconnect blue2antenna cable.
Disconnect black3cable.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 129/218
iMac (21.5-inch, Late 2009) Take Apart — AirPort Antenna 1292009-11-24
First Steps
Remove:Glass Panel•LCD Panel•
Note: There is a secondAirPort antenna built-into rear housing behindApple logo on back ofiMac, however, it is notremovable and can onlybe repaired via rearhousing replacement.
Tools
ESD wrist strap• Torx T8 screwdriver•
AirPort Antenna
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 130/218
iMac (21.5-inch, Late 2009) Take Apart — AirPort Antenna 1302009-11-24
Removal
Remove T8 screws: 1(2) 922-4723
Disconnect black2antenna cable fromAirPort card.
Peel up clear tape3securing antenna
cable to rear housing.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 131/218
iMac (21.5-inch, Late 2009) Take Apart — AirPort Card 1312009-11-24
First Steps
Remove:Glass Panel•LCD Panel•
Tools
ESD wrist strap• Torx T6 screwdriver•
AirPort Card
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 132/218
iMac (21.5-inch, Late 2009) Take Apart — AirPort Card 1322009-11-24
Removal
Remove T6 screw: 1(1) 922-8579
Disconnect 2 antenna2cables.
Important: Antennacables and connectors aredelicate. If the shorter ofthe two antenna cables is
damaged, you will need toreplace rear housing.
Hold AirPort card by3edges and pull it outof the slot.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 133/218
iMac (21.5-inch, Late 2009) Take Apart — AirPort Cable 1332009-11-24
First Steps
Remove:Glass Panel•LCD Panel•
Tools
ESD wrist strap•
AirPort Cable
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 134/218
iMac (21.5-inch, Late 2009) Take Apart — AirPort Cable 1342009-11-24
Removal
Disconnect cable1from AirPort carrierboard.
Disconnect cable (10)2from top center oflogic board.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 135/218
iMac (21.5-inch, Late 2009) Take Apart — AirPort Carrier Board 1352009-11-24
First Steps
Remove:Glass Panel•LCD Panel•AirPort Card•
Tools
ESD wrist strap• Torx T10 screwdriver•
AirPort Carrier Board
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 136/218
iMac (21.5-inch, Late 2009) Take Apart — AirPort Carrier Board 1362009-11-24
Removal
Remove T10 screws: 1(2) 922-6850
Disconnect at black2ribbon cable.
Observe how DC3power cable routesunderneath AirPort
carrier board,between the twoscrew posts.
Reassembly Note:Although screw holescan line up with postswhen board is rotated180 degrees from correctposition, board shouldbe installed with cableconnector on the right.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 137/218
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 138/218
iMac (21.5-inch, Late 2009) Take Apart — LED Backlight Board 1382009-11-24
Removal
Remove T10 screws: 1(2) 922-6850
Lift up board, ip over,
2 and disconnect powerconnector.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 139/218
iMac (21.5-inch, Late 2009) Take Apart — Power Supply 1392009-11-24
First Steps
Remove:Glass Panel•LCD Panel•
Warning: HIGH VOLTAGE:Use extreme cautionwhen working aroundthe power supply, whichcontains a high-voltagecapacitor that may remaincharged for severalminutes even whencomputer is unplugged.
Never touch leads ontop side of power supply,especially those nearwarning sign.
Tools
ESD wrist strap• Torx T10 screwdriver•
Power Supply
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 140/218
iMac (21.5-inch, Late 2009) Take Apart — Power Supply 1402009-11-24
Removal
Remove T10 screws: 1(1) 922-6850, short (S)
(1) 922-9243, long (L)
(2) 922-9244, machine(M)
Reassembly Note: Installself-tapping screws on leftside (short on top, longon bottom) and machinescrews on right side.
Lift up, ip over and
2 disconnect 2 cables.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 141/218
iMac (21.5-inch, Late 2009) Take Apart — Backlight Pressure Wall 1412009-11-24
First Steps
Remove:Glass Panel•LCD Panel•Power Supply•
Tools
ESD wrist strap•
Backlight Pressure Wall
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 142/218
iMac (21.5-inch, Late 2009) Take Apart — Backlight Pressure Wall 1422009-11-24
Removal
Lift pressure wall o1posts in rear housing.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 143/218
iMac (21.5-inch, Late 2009) Take Apart — Power Supply Pressure Wall 1432009-11-24
First Steps
Remove:Glass Panel•LCD Panel•Power Supply•
Tools
ESD wrist strap•
Power Supply Pressure Wall
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 144/218
iMac (21.5-inch, Late 2009) Take Apart — Power Supply Pressure Wall 1442009-11-24
Removal
Lift pressure wall o1posts in rear housing.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 145/218
iMac (21.5-inch, Late 2009) Take Apart — Hard Drive 1452009-11-24
First Steps
Remove:Glass Panel•LCD Panel•
Tools
ESD wrist strap• Torx T10 screwdriver•
Hard Drive
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 146/218
iMac (21.5-inch, Late 2009) Take Apart — Hard Drive 1462009-11-24
Removal
Remove T10 screws: 1(2) 922-6850
Disconnect 2 cables:2HD power cable•HD data cable •
Leave small HD tempsensor cable attached.
Slide hard drive up3slightly to lift pins outof 2 rubber grommetsin mechanism.
Disconnect HD sensor4cable from top oflogic board.
Important: Do notdisconnect HD sensorcable from harddrive. Each drivemanufacturer hasa dierent type of
sensor cable, whichis provided with areplacement drive.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 147/218
iMac (21.5-inch, Late 2009) Take Apart — Hard Drive 1472009-11-24
Reassembly
Replacement Note:1If installing a newhard drive, transferthe following:hard drive bracket•(2) T10 screws•922-9136
(2) T10 screw pins •922-7001
Note:2 Each hard drivevendor has a uniquesensor cable. Do notmix and match tempsensor cables.
Important:3 Wheninstalling a WesternDigital drive:orient drive with•circuit board facingup (as shown);connect temp sensor•cable to hard drivepins as shown,leaving 2 left pinsunconnected.
If sensor cable isinstalled incorrectly,hard drive fan will runat full speed.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 148/218
iMac (21.5-inch, Late 2009) Take Apart — Hard Drive Sensor Cable 1482009-11-24
First Steps
Remove:Glass Panel•LCD Panel•
Note: Each hard drivemanufacturer has adierent type of sensorcable, which is includedwith a replacement drive.
If replacing sensor cableonly, be sure to ordercorrect cable for drivemanufacturer.
Tools
ESD wrist strap•
Hard Drive Sensor Cable
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 149/218
iMac (21.5-inch, Late 2009) Take Apart — Hard Drive Sensor Cable 1492009-11-24
Removal
Disconnect cable1from hard drive andlogic board.
Note: Do not reusetemp sensor cable. Anew sensor cable isincluded with eachreplacement drive.
Each hard drivemanufacturer has aunique sensor cable.
Reassembly
Important:1 Wheninstalling a WesternDigital drive:orient drive with•circuit board facingup (as shown);connect temp sensor•cable to hard drivepins as shown,leaving 2 left pinsunconnected.
If sensor cable isinstalled incorrectly,hard drive fan will runat full speed.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 150/218
iMac (21.5-inch, Late 2009) Take Apart — Bluetooth Cable 1502009-11-24
First Steps
Remove:Glass Panel•LCD Panel•Power Supply•Power Supply Pressure•
WallHard Drive•
Tools
ESD wrist strap•
Bluetooth Cable
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 151/218
iMac (21.5-inch, Late 2009) Take Apart — Bluetooth Cable 1512009-11-24
Removal
Disconnect cable1from Bluetooth board.
Disconnect cable (#5)2from top center of
logic board.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 152/218
iMac (21.5-inch, Late 2009) Take Apart — Bluetooth Cable 1522009-11-24
Peel up foil tape3securing cable to rear
housing.
Observe cable routing4for reassembly. Referto photograph inInternal Views section.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 153/218
iMac (21.5-inch, Late 2009) Take Apart — Camera Cable 1532009-11-24
First Steps
Remove:Glass Panel•LCD Panel•Power Supply•Power Supply Pressure•
WallHard Drive•Camera•
Tools
ESD wrist strap•
Camera Cable
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 154/218
iMac (21.5-inch, Late 2009) Take Apart — Camera Cable 1542009-11-24
Removal
Disconnect cable1from camera.
Disconnect cable (#6)2from top center oflogic board.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 155/218
iMac (21.5-inch, Late 2009) Take Apart — Camera Cable 1552009-11-24
Peel up foil tape3securing cable to rear
housing.
Observe cable routing4for reassembly. Referto photograph inInternal Views section.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 156/218
iMac (21.5-inch, Late 2009) Take Apart — Optical Drive 1562009-11-24
First Steps
Remove:Glass Panel•LCD Panel•
Important: Whenservicing optical drive,handle it by edges only.Pressing elsewhere ondrive could damageinternal mechanism.
Tools
ESD wrist strap• Torx T10 screwdriver•Black stick •
Optical Drive
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 157/218
iMac (21.5-inch, Late 2009) Take Apart — Optical Drive 1572009-11-24
Removal
Remove T10 screws: 1(4) 922-6850
Disconnect temp
2 sensor cable fromconnector on lowerright side of logicboard.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 158/218
iMac (21.5-inch, Late 2009) Take Apart — Optical Drive 1582009-11-24
Lift optical drive3
slightly and wiggleoptical drive datacable away fromoptical drive. A blackstick may be helpful.
Pull optical drive away4from slot opening inrear housing.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 159/218
iMac (21.5-inch, Late 2009) Take Apart — Optical Drive Sensor Cable 1592009-11-24
First Steps
Remove:Glass Panel•LCD Panel•
Note: A replacementoptical drive will include anew sensor cable.
Tools
ESD wrist strap•
Optical Drive Sensor Cable
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 160/218
iMac (21.5-inch, Late 2009) Take Apart — Optical Drive Sensor Cable 1602009-11-24
Removal
Peel up foam gasket1to release sensor endof cable.
Disconnect cable2from logic board.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 161/218
iMac (21.5-inch, Late 2009) Take Apart — Optical Drive Fan 1612009-11-24
First Steps
Remove:Glass Panel•LCD Panel•Optical Drive•
Tools
ESD wrist strap• Torx T10 screwdriver•
Optical Drive Fan
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 162/218
iMac (21.5-inch, Late 2009) Take Apart — Optical Drive Fan 1622009-11-24
Removal
Remove T10 screw: 1(1) 922-9236
Lift fan up and2disconnect cable from
logic board.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 163/218
iMac (21.5-inch, Late 2009) Take Apart — SD Board 1632009-11-24
First Steps
Remove:Glass Panel•LCD Panel•
Tools
ESD wrist strap• Torx T8 screwdriver•Black stick •
SD Board
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 164/218
iMac (21.5-inch, Late 2009) Take Apart — SD Board 1642009-11-24
Removal
Remove T8 screw: 1(1) 922-9241
Using a black stick,2gently pry SD boardup and out of rearhousing.
Disconnect cable.3
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 165/218
iMac (21.5-inch, Late 2009) Take Apart — SD Cable 1652009-11-24
First Steps
Remove:Glass Panel•LCD Panel•Optical Drive•Optical Drive Fan•
Tools
ESD wrist strap•
SD Cable
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 166/218
iMac (21.5-inch, Late 2009) Take Apart — SD Cable 1662009-11-24
Removal
Disconnect cable1from SD board andlogic board.
Peel up foil holding2cable to rear housing.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 167/218
iMac (21.5-inch, Late 2009) Take Apart — Audio Cable 1672009-11-24
First Steps
Remove:Glass Panel•LCD Panel•
Tools
ESD wrist strap• Torx T10 screwdriver•
Audio Cable
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 168/218
iMac (21.5-inch, Late 2009) Take Apart — Audio Cable 1682009-11-24
Removal
Remove T10 screws: 1(2) 922-9245
Disconnect cable2from logic board.
Reassembly Note:A black stick can behelpful for guidingand aligning audioports with rearhousing.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 169/218
iMac (21.5-inch, Late 2009) Take Apart — IR Board & Cable 1692009-11-24
First Steps
Remove:Glass Panel•LCD Panel•
Note: A new IR boardincludes a new cable. Thecable is not available as aseparate part.
Tools
ESD wrist strap•
IR Board & Cable
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 170/218
iMac (21.5-inch, Late 2009) Take Apart — IR Board & Cable 1702009-11-24
Removal
Disconnect IR cable1from logic board.
With 2 ngers, wiggle2IR mounting bracketup and o mountingpost.
Reassembly Note:Pull the front housing outslightly to make room forIR mounting bracket to
slide onto IR mountingpost.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 171/218
iMac (21.5-inch, Late 2009) Take Apart — Logic Board 1712009-11-24
First Steps
Remove:Glass Panel•LCD Panel•Power Supply•Backlight Pressure Wall•
Power Supply Pressure•WallOptical Drive•Optical Drive Fan•IR Board•
Note: Congurations withintegrated graphics do nothave the silver mountingbracket at upper rightwhich holds the video
card and its heatsink.
Tools
ESD wrist strap• Torx T10 screwdriver•
Logic Board
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 172/218
iMac (21.5-inch, Late 2009) Take Apart — Logic Board 1722009-11-24
Removal
Remove T10 screws: 1(2) 922-6800, short (S) (only 1 if unit has novideo card bracket)
(2) 922-9237, medium20mm (M)
(3) 922-9243, long
24mm (L)
Disconnect cables2from left side of logicboard:power button (1)•CPU fan (2)•
Note: IR cable (3)should have alreadybeen disconnected.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 173/218
iMac (21.5-inch, Late 2009) Take Apart — Logic Board 1732009-11-24
Disconnect cables3from top center of
logic board:ambient temp (4)•Bluetooth (5)•camera (6)•hard drive sensor (7)•hard drive fan (8)•microphone (9)•AirPort (10)•audio cable (13)•right speaker (14)•left speaker (15)•
Note: LCD tempsensor (11) and LVDS(12) cables shouldhave already beendisconnected.
Disconnect SD cable4
(16) from right side oflogic board:
Note: Optical drivetemp (17) and opticaldrive fan (18) cablesshould have alreadybeen disconnected.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 174/218
iMac (21.5-inch, Late 2009) Take Apart — Logic Board 1742009-11-24
Tape cables back5so they do not
get trapped underlogic board duringreassembly.
Peel up foil holding6
copper square to rearhousing.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 175/218
iMac (21.5-inch, Late 2009) Take Apart — Logic Board 1752009-11-24
Lift logic board7up and out of rear
housing.
Careful! There are 3 cablesto disconnect from backside of logic board in nextstep on next page.
Note: Logic board may beeasier to lift out if RAM isremoved rst.
Note: Logic boardshown in this image hasintegrated graphics, andtherefore no video cardbracket.
Important: Always use
2 hands to support logicboard and heatsink.Handling board incorrectlycould ex board anddamage chips and circuits.Never handle board byheatsink or metal frame.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 176/218
iMac (21.5-inch, Late 2009) Take Apart — Logic Board 1762009-11-24
On back side of logic8board, disconnect
hard drive data cable(19), optical drive datacable (20), and DCpower cable (21).
Reassembly Note: Observe how optical drivedata cable routes aroundcopper pipe on logicboard.
If this cable is not correctlyrouted before reinstallinglogic board, it may bedicult to properly seatoptical drive in rearhousing later.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 177/218
iMac (21.5-inch, Late 2009) Take Apart — Logic Board 1772009-11-24
Replacement
If installing a newreplacement logic board,note 4 things:
Verify that tamper1indicator labels onfront and back ofheatsink assembly areintact. If labels havebeen removed ortampered with, logicboard is not eligible
for exchange.
Transfer RAM memory2from old logic boardto new logic board.
Apply new Ethernet3ID label (included inbox with new logicboard) to bottom ofstand.
Use the4 Blank BoardSerializer tool toset computer’s serialnumber on new logicboard.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 178/218
iMac (21.5-inch, Late 2009) Take Apart — Video Card 1782009-11-24
First Steps
Remove:Glass Panel•LCD Panel•Power Supply•Backlight Pressure Wall•
Power Supply Pressure•WallOptical Drive•Optical Drive Fan•IR Board•Logic Board•
Note: Video card attachesto back side of logicboard.
Note: Congurations withintegrated graphics donot have a video card.
Tools
ESD wrist strap• Torx T10 screwdriver• Torx T8 screwdriver•
Video Card
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 179/218
iMac (21.5-inch, Late 2009) Take Apart — Video Card 1792009-11-24
Removal
Remove T8 screws on1video card: (2) 922-4723
Remove T10 screw up2near heatsink: (1) 922-7971
Disconnect cable3from logic board.
(1) Lift up video card4and heatsink and(2) slide card out ofslot on logic board.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 180/218
iMac (21.5-inch, Late 2009) Take Apart — Battery 1802009-11-24
First Steps
Remove:Glass Panel•LCD Panel•Power Supply•Backlight Pressure Wall•
Power Supply Pressure•WallOptical Drive•Optical Drive Fan•IR Board•Logic Board•
Note: Battery is located onback side of logic board.
Tools
ESD wrist strap•Black stick •
Battery
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 181/218
iMac (21.5-inch, Late 2009) Take Apart — Battery 1812009-11-24
Removal
Use a black stick to1pry battery fromsocket on logic board.
Reassembly
Make sure battery1socket is open andfree of dust.
Press battery (922-28802) into socket withengraved markings (+side) facing up.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 182/218
iMac (21.5-inch, Late 2009) Take Apart — Hard Drive Data Cable 1822009-11-24
First Steps
Remove:Glass Panel•LCD Panel•Power Supply•Backlight Pressure Wall•
Power Supply Pressure•WallOptical Drive•Optical Drive Fan•IR Board•Logic Board•
Note: Hard drive datacable attaches to backside of logic board.
Tools
ESD wrist strap•
Hard Drive Data Cable
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 183/218
iMac (21.5-inch, Late 2009) Take Apart — Hard Drive Data Cable 1832009-11-24
Removal
Disconnect data cable1from hard drive.
Disconnect hard drive2data cable (#19) fromback side of logicboard.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 184/218
iMac (21.5-inch, Late 2009) Take Apart — Optical Drive Data Cable 1842009-11-24
First Steps
Remove:Glass Panel•LCD Panel•Power Supply•Backlight Pressure Wall•
Power Supply Pressure•WallOptical Drive•Optical Drive Fan•IR Board•Logic Board•
Note: Optical drive datacable attaches to backside of logic board.
Tools
ESD wrist strap•
Optical Drive Data Cable
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 185/218
iMac (21.5-inch, Late 2009) Take Apart — Optical Drive Data Cable 1852009-11-24
Removal
Disconnect optical1drive data cable (#20)from back side oflogic board.
Reassembly Note: Observe how optical drive
data cable routes aroundcopper pipe on logicboard.
If this cable is not correctlyrouted before reinstallinglogic board, it may bedicult to properly seatoptical drive in rearhousing later.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 186/218
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 187/218
iMac (21.5-inch, Late 2009) Take Apart — CPU Fan 1872009-11-24
First Steps
Remove:Glass Panel•LCD Panel•Power Supply•Backlight Pressure Wall•
Power Supply Pressure•WallOptical Drive•Optical Drive Fan•IR Board•Logic Board•
Tools
ESD wrist strap• Torx T10 screwdriver•
CPU Fan
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 188/218
iMac (21.5-inch, Late 2009) Take Apart — CPU Fan 1882009-11-24
Removal
Remove T10 screws: 1(2) 922-9236
Lift fan up and out of2rear housing.
Note guidepost3on fan that willt into bottom ofrear housing onreassembly.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 189/218
iMac (21.5-inch, Late 2009) Take Apart — CPU Fan 1892009-11-24
Note routing of4ambient temp sensor
cable and left speakercable through clipson CPU fan.
Remove ambient5temp sensor and leftspeaker cables fromCPU fan.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 190/218
iMac (21.5-inch, Late 2009) Take Apart — Ambient Temp Sensor 1902009-11-24
First Steps
Remove:Glass Panel•LCD Panel•Power Supply•Backlight Pressure Wall•
Power Supply Pressure•WallOptical Drive•Optical Drive Fan•IR Board•Logic Board•CPU Fan•
Tools
ESD wrist strap•
Ambient Temp Sensor
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 191/218
iMac (21.5-inch, Late 2009) Take Apart — Ambient Temp Sensor 1912009-11-24
Removal
Note routing of1ambient temp sensorcable through clipson CPU fan.
Remove ambient2temp sensor fromCPU fan.
Note routing of cable3and any tape securing
it to rear housing.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 192/218
iMac (21.5-inch, Late 2009) Take Apart — Left Speaker 1922009-11-24
First Steps
Remove:Glass Panel•LCD Panel•Optical Drive•Optical Drive Fan•
IR Board•Power Supply•Backlight Pressure Wall•Power Supply Pressure•WallLogic Board•CPU Fan•
Tools
ESD wrist strap• Torx T10 screwdriver•
Left Speaker
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 193/218
iMac (21.5-inch, Late 2009) Take Apart — Left Speaker 1932009-11-24
Removal
Remove T10 screw: 1(1) 922-9242
Remove tape securing2cable to rear housing.
Observe cable routing3for reassembly. Referto photograph inInternal Views section.
Rotate speaker to the4right and lift out ofrear housing.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 194/218
iMac (21.5-inch, Late 2009) Take Apart — Right Speaker 1942009-11-24
First Steps
Remove:Glass Panel•LCD Panel•Power Supply•Backlight Pressure Wall•
Power Supply Pressure•WallOptical Drive•Optical Drive Fan•IR Board•Logic Board•Audio Cable•
Tools
ESD wrist strap• Torx T10 screwdriver•
Right Speaker
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 195/218
iMac (21.5-inch, Late 2009) Take Apart — Right Speaker 1952009-11-24
Removal
Remove T10 screw: 1(1) 922-9242
Note cable routing2through guide in rearhousing.
Rotate speaker to the3left and lift out of rear
housing.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 196/218
iMac (21.5-inch, Late 2009) Take Apart — Hard Drive Fan 1962009-11-24
First Steps
Remove:Glass Panel•LCD Panel•Power Supply•Backlight Pressure Wall•
Power Supply Pressure•WallOptical Drive•Optical Drive Fan•IR Board•Logic Board•
Tools
ESD wrist strap• Torx T10 screwdriver•
Hard Drive Fan
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 197/218
iMac (21.5-inch, Late 2009) Take Apart — Hard Drive Fan 1972009-11-24
Removal
Remove T10 screw: 1(1) 922-9236
Lift fan straight up2and o guideposts.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 198/218
iMac (21.5-inch, Late 2009) Take Apart — Mechanism Cover 1982009-11-24
First Steps
Remove:Glass Panel•LCD Panel•Power Supply•Backlight Pressure Wall•Power Supply Pressure•
WallOptical Drive•Optical Drive Fan•IR Board•Logic Board•Hard Drive•Hard Drive Fan•
Tools
ESD wrist strap• Torx T10 screwdriver•
Mechanism Cover
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 199/218
iMac (21.5-inch, Late 2009) Take Apart — Mechanism Cover 1992009-11-24
Removal
Peel up foil tape.1
Remove T10 screws: 2(2) 922-9238 (same
screws used onmechanism)
(2) 922-6800 (smallerscrews closer to rearhousing vent)
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 200/218
iMac (21.5-inch, Late 2009) Take Apart — Stand 2002009-11-24
First Steps
Remove:Glass Panel•LCD Panel•Optical Drive•Optical Drive Fan•IR Board•
Power Supply•Backlight Pressure Wall•Power Supply Pressure•WallLogic Board•Hard Drive•Hard Drive Fan•Mechanism Cover•
Tools
ESD wrist strap• Torx T10 screwdriver•
Stand
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 201/218
iMac (21.5-inch, Late 2009) Take Apart — Stand 2012009-11-24
Removal
Remove T10 screws: 1(7) 922-8209
Replacement Note:Reinstall furthest left andright screws rst and thenreinstall middle 5 screws.
Lift rear housing o2stand.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 202/218
iMac (21.5-inch, Late 2009) Take Apart — Mechanism 2022009-11-24
First Steps
Remove:Glass Panel•LCD Panel•Power Supply•Backlight Pressure Wall•Power Supply Pressure•
WallOptical Drive•Optical Drive Fan•IR Board•Logic Board•Hard Drive•Hard Drive Fan•Mechanism Cover•Stand•
Tools
ESD wrist strap• Torx T10 screwdriver•
Mechanism
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 203/218
iMac (21.5-inch, Late 2009) Take Apart — Mechanism 2032009-11-24
Removal
Remove T10 screws: 1(6) 922-9238
Peel down foil on2mechanism.
Replacement Note: Mechanism upper right
corner tucks under opticaldrive pressure wall.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 204/218
iMac (21.5-inch, Late 2009) Take Apart — Microphone Cable 2042009-11-24
First Steps
Microphone cable is partof rear housing and is notavailable as a separatepart.
If microphone cable needs
to be replaced, follow rearhousing procedure.
Microphone Cable
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 205/218
iMac (21.5-inch, Late 2009) Take Apart — Rear Housing 2052009-11-24
First Steps
Remove:Glass Panel•Camera•LCD Panel•Bluetooth Board•AirPort Cable•
AirPort Carrier Board•LED Backlight Board•Power Supply•Hard Drive•Bluetooth Cable•Camera Cable•Optical Drive•Optical Drive Fan•SD Board•SD Cable•Audio Cable•
IR Board & Cable•Logic Board•DC Power Cable•CPU Fan•Ambient Temp Sensor•Left Speaker•Right Speaker•Hard Drive Fan•Mechanism Cover•Stand•Mechanism•
Rear Housing
With all other modules removed, rear housing is the remaining assembly.
A new rear housing includes the following parts, which are also available separately:Bluetooth & AirPort antennas along top of rear housing•pressure wall between LED Backlight Board and Power Supply•pressure wall between Power Supply and Hard Drive•
A new rear housing also includes the following parts, which are NOT available separately:
AirPort antenna in silver circle behind Apple logo on back of computer•microphone and cable•power button and cable•AC inlet•
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 206/218
iMac (21.5-inch, Late 2009) Take Apart — Rear Housing 2062009-11-24
Important: Handling rearhousing part incorrectly
could ex aluminum andcause alignment issues.
Always handle rearhousing with 2 hands inthe lower left and rightcorners.
Never carry rear housingwith a single hand, or byholding the aluminum“chin” (where Apple logo
appears on front).
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 207/218
© 2009 Apple Inc. All rights reserved.
Apple Technician Guide
ViewsiMac (21.5-inch, Late 2009)
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 208/218
iMac (21.5-inch, Late 2009) Views — Exploded Views 2082009-11-24
Exploded Views
iMac (21.5-inch, Late 2009), Part 1
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 209/218
iMac (21.5-inch, Late 2009) Views — Exploded Views 2092009-11-24
iMac (21.5-inch, Late 2009), Part 2
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 210/218
iMac (21.5-inch, Late 2009) Views — Exploded Views 2102009-11-24
iMac (21.5-inch, Late 2009), Part 3
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 211/218
iMac (21.5-inch, Late 2009) Views — Screw Chart 2112009-11-24
Screw Chart
Note: Screws are not to scale.
922-9246 T10
LCD panel (8)
922-9239 T10
Camera (2)
922-4723 T8
Bluetooth antenna (2), AirPortantenna (2), video card (2)
922-9247 T8
Bluetooth board (1)
922-8579 T6
AirPort card (1)
922-6850 T10
AirPort carrier board (2), LEDbacklight board (2), Powersupply (1), Hard drive (2),Optical drive (4), AC inlet (3)
922-9244 T10
Power supply, machine (2)
922-9243 T10
Power supply, long (1),Logic board, long 24mm (3)
922-9241 T8
SD board (1)
922-9136
T10
Hard drive clip to HDD (2)
922-7001
T10
Hard drive pins (2)
922-9245
T10
Audio cable (2)
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 212/218
iMac (21.5-inch, Late 2009) Views — Screw Chart 2122009-11-24
922-9236 T10
Optical fan (1), CPU fan (2),Hard drive fan (1)
922-6800 T10
Logic board, short (1-2), Mechanism cover, small (2)
922-9237 T10
Logic board, medium 20mm(2)
922-7971 T10
Video card bracket (1)
922-9242 T10
Right speaker (1),Left speaker (1)
922-9238 T10
Mechanism cover (2),Mechanism (6)
922-8209 T10
Stand (7)
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 213/218
iMac (21.5-inch, Late 2009) Views — External Views 2132009-11-24
External Views
Front View
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 214/218
iMac (21.5-inch, Late 2009) Views — External Views 2142009-11-24
Rear View
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 215/218
iMac (21.5-inch, Late 2009) Views — External Views 2152009-11-24
I/O Ports
Headphone-out/optical digital audio-out1.Audio-in/optical digital audio-in2.(4) USB 2.03.FireWire 8004.Mini DisplayPort5.Gigabit Ethernet6.
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 216/218
iMac (21.5-inch, Late 2009) Views — Internal Views 2162009-11-24
Internal Views
Photo of Components below LCD
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 217/218
iMac (21.5-inch, Late 2009) Views — Internal Views 2172009-11-24
Photo of Components below Logic Board
8/20/2019 Technical Manual Imac21 Inch Late09
http://slidepdf.com/reader/full/technical-manual-imac21-inch-late09 218/218
Logic Board, Front Side